STIH) Technical Information Cut-off machine STIHL Cutquik TS 410, 420 Series Guard with defined adjustment range
|
|
- Raymond Matthews
- 6 years ago
- Views:
Transcription
1 STIH) Technical Information Cut-off machine STIHL Cutquik TS 40, 40 Series 48 Contents. Guard with defined adjustment range. Belt guard, screw. Set of instruction labels 4. Summary. Guard with defined adjustment range. Adjustment range In STIHL Cutquik TS 40, 40 cut-off machines, the adjustment range (A and B respectively) of the guard will be determined by the stop pin () installed into the cast arm and by the lugs (arrows) molded onto the guard (). B A 70TI06 KN Adjustment range (A), Guard mounted on the inboard side Adjustment range (B), Guard mounted on the outboard side TI_5_009_0_0_0.fm englisch / English
2 Page Technical Information Cast arm. Guard 70TI07 KN 70TI08 KN The previous versions of the cast arm (TS 40) and cast arm (TS 40) are being replaced by the new versions of the cast arm (TS 40) and cast arm (TS 40). The new versions differ by a threaded hole () for installing in the stop pin (see b.4) and additional holes () for fastening the limit stop (see b.5). Spare parts The previous versions of cast arm (TS 40) and cast arm (TS 40) without a threaded hole and without additional holes are no longer available. The new versions of cast arm (TS 40) and cast arm (TS 40) can also be used for older machines. Previous versions of the guard New versions of the guard The previous versions of the guard dia. 00 mm (") ( ) and the guard dia. 50 mm (4") ( ) are being replaced by the new versions of the guard dia. 00 mm (") ( ) and the guard dia. 50 mm (4") ( ). The new versions differ from the previous versions by casted lugs (arrows), together with the stop pins (see b.4) installed into the cast arm (see b.) to determine the adjustment range (see b.) of the guard. Spare parts The previous versions of the guard dia. 00 mm (") ( ) and the guard dia. 50 mm (4") ( ) remain available for older machines. Service notes The previous versions of the guard dia. 00 mm (") ( ) and the guard dia. 50 mm (4") ( ) may only be installed in machines with the previous guards. The new versions of the guard dia. 00 mm (") ( ) and the guard dia. 50 mm (4") ( ) may only be installed in machines with the new guards. TI_5_009_0_0_0.fm
3 Technical Information Page.4 Stop pin.6 Rubber buffer 70TI09 KN 70TI07 KN With the introduction of the new guards (see b.), the stop pin () and the limit stop (see b.5) are introduced. The stop pin () installed into the cast arm (), together with the lugs molded onto the guard (see b.) determine the adjustment range (see b.). Tightening torques Stop pin / cast arm 5 Nm Previous versions of the cast arm, rubber buffer and screw New versions of the cast arm with guard and the stop pin The stop pin (, see b.4) and lugs cast onto the guard (see b.) determine the adjustment range (see b.), the rubber buffer () and the screw IS-M5x6-0.9 () ( ) have been eliminated. Spare parts.5 Limit stop The previous versions of the rubber buffer and the screw IS-M5x6-0.9 ( ) remain available for machines with the previous guards. 70TI00 KN With the introduction of the new guards (see b.), the limit stop () and the stop pin (see b.4) are introduced. The limit stop () is fastened to the cast arm with the pan head self-tapping screw IS-P4x6 () ( ). Tightening torques Limit stop / cast arm.8 Nm TI_5_009_0_0_0.fm
4 Page 4 Technical Information Reconfiguring the "cast arm with guard" from guard on the inboard side to guard on the outboard side The "cast arm with guard" is mounted on the inboard side by the manufacturer. The "cast arm with guard" can also be mounted on the outboard side depending on requirements. Assembly on the inboard side is recommended for better balance.. Remove the abrasive wheel Remove water attachment Remove the adjusting lever. Loosen the banjo bolt () with the combination wrench and remove it together with the seal in the process, remove the square nut from the guide on the inside of the guard. Remove bolt (). Turn the adjusting lever () upwards and remove 70TI0 KN 70TI0 KN Slacken the V-belt. Loosen the banjo bolt () with the combination wrench in the process, remove the square nut from the guide on the inside of the guard 0. Remove the water hose () with connector from the adjusting lever (). Remove the water hose () from the guide (arrows) in the V-belt guard 70TI0 KN. Loosen the nuts () do not remove them. Turn the tensioning nut () counterclockwise with the combination wrench approx. /4 turn, max. to stop = 0 TI_5_009_0_0_0.fm
5 Technical Information Page 5 Remove the V-belt guard Remove the "cast arm with guard" 70TI04 KN. Loosen screw () in machines with the new belt guard (see b ), the screw is secured on the belt guard to prevent loss. Raise the V-belt guard () slightly and pull off towards front 70TI06 KN. Remove the nuts (). Remove the "starter cover with rewind starter" () 4 70TI05 KN. Remove the "cast arm with guard" () from the studs Preparing the "cast arm with guard" for outboard mounting. Remove the V-belt () from the front pulley (4) 70TI07 KN. Remove stop pin () TI_5_009_0_0_0.fm
6 Page 6 Technical Information Mount "cast arm with guard" guard on the outboard side A 4 5. Turn the guard so that it is in the position shown (see picture). Install and tighten the stop pin (). Move the adjusting lever () to position (A). Install the bolt () and tighten. Loosen the bolt (4) of the limit stop (5). Remove the limit stop (5) 6 70TI08 KN 4. Position the oblong holes () in the "cast arm and guard" onto to the studs (), install the ribbed V-belt over the front pulley. Check that the belt adjustment moves easily. The belt tensioner () must nest against the lug (4) 70TI00 KN TI09 KN. Turn the "cast arm with guard" so that the guard is on the outboard side. Insert limit stop (5) align the hole in the limit stop with the hole in the cast arm. Install the screw (4) and tighten. Insert the square nut into the guide of the guard and hold in place. Install the shorter banjo bolt (6) and washer at the adjusting lever and tighten with the combination wrench Fit the "starter cover with rewind starter" (5) over the studs (). Tighten the nuts (6) by hand 70TI0 KN TI_5_009_0_0_0.fm
7 Technical Information Page 7 Check the adjustment range of the guard TI0 KN. Push the V-belt guard (7) into place. Install and tighten screw (8) in machines with the new belt guard (see b ), the screw is secured on the belt guard to prevent loss A Connect water connection 70TI04 KN. Rotate the guard forwards and backwards as far as possible adjustment range (A) must be limited by the stop pin 70TI0 KN. Insert the longer banjo bolt () through the connector () of the water attachment observe the position of the connector. Insert the square nut into the guide of the guard and hold in place. Install the support with the longer banjo bolt onto the adjusting lever () install the banjo bolt and tighten with the combination wrench. Insert the water hose into the guide in the V-belt guard (arrow) from the shut-off cock towards the guard avoid tight radiuses. Tension the ribbed V-belt TI_5_009_0_0_0.fm
8 Page 8 Technical Information Reconfiguring the "cast arm with guard" from guard on the outboard side to guard on the inboard side. Remove the abrasive wheel. Remove water attachment. Remove the adjusting lever. Slacken the V-belt. Remove the V-belt guard. Remove the V-belt. Remove the "cast arm with guard" Preparing the "cast arm with guard" for inboard mounting. Turn the guard so that it is in the position shown (see picture). Install and tighten the stop pin (). Install the adjusting lever. Mount "cast arm with guard" guard on the inboard side. Install the V-belt. Install the V-belt guard. Connect water connection. Tension the ribbed V-belt 70TI07 KN. Loosen the bolt () of the limit stop (). Remove the limit stop () 70TI05 KN Check the adjustment range of the guard 70TI06 KN A. Turn the "cast arm with guard" so that the guard is on the inboard side. Insert limit stop () align the hole in the limit stop with the hole in the cast arm. Install the screw () and tighten. Remove stop pin () Rotate the guard forwards and backwards as far as possible adjustment range (A) must be limited by the stop pin 70TI08 KN TI_5_009_0_0_0.fm
9 Technical Information Page 9. Belt guard, screw 7,, TI07 KN Spare parts The previous versions of the belt guard (TS 40) and the belt guard (TS 40) are no longer available. The new versions of belt guard (TS 40) and belt guard (TS 40) can also be used for older machines. The previous versions of spline screw IS-M5x0x-0.9 ( ) and hollow rivet DIN79-7.5xx6.8 ( ) remain available for older machines. Previous versions of the belt guard and the screw New versions of the belt guard and the screw The previous versions of the belt guard () (TS 40) and the belt guard () (TS 40) are being replaced by the new versions of the belt guard () (TS 40) and the belt guard (4) (TS 40). The new versions of the belt guard (, 4) are fastened to the cast arm with the new screw IS-M5x (5) ( ). In the versions of the belt guard (, 4), the new screw IS-M5x (5) ( ) is secured against loss. The previous versions of the spline screw IS-M5x0x-0.9 (6) ( ) and the hollow rivet DIN79-7.5xx6.8 (7) ( ) are no longer needed. Tightening torques Belt guard / cast arm 6 Nm TI_5_009_0_0_0.fm
10 Page 0 Technical Information Set of instruction labels. Set of instruction labels (only for TS 40). Set of instruction labels (only for TS 40) 70TI07 KN 70TI07 KN Previous versions of the instruction labels New versions of the instruction labels Previous versions of the instruction labels New versions of the instruction labels TS 40 only, the previous versions of instruction label () and instruction label () are being replaced by the new "set of instruction labels" () Spare parts/service notes The previous versions of instruction label () and instruction label () are no longer available. The new "set of instruction labels" () can also be used with older STIHL Cutquik TS 40 cutoff machines. TS 40 only, the previous versions of instruction label () and instruction label () are being replaced by the new "set of instruction labels" () Spare parts/service notes The previous versions of instruction label () and instruction label () are no longer available. The new "set of instruction labels" () can also be used with older STIHL Cutquik TS 40 cutoff machines. Always attach both instruction labels in the new "set of instruction labels" () Always attach both instruction labels in the new "set of instruction labels" () TI_5_009_0_0_0.fm
11 Technical Information Page 4. Summary Item Part Name Previous New Rem. Cast arm (TS 40) ) ) Cast arm (TS 40) ) ) Guard dia. 00 mm (") (TS 40) ) 4) 4 Guard dia. 50 mm (4") (TS 40) ) 4) 5 Stop pin Limit stop Pan head self-tapping screw IS-P4x Rubber buffer ) 9 Spline screw IS-M5x ) 0 Belt guard (TS 40); ) including Item 4 Belt guard (TS 40); ) including Item 6 Belt guard (TS 40); ) including Item 4 Belt guard (TS 40); ) including Item 6 4 Hollow rivet DIN79-7.5xx ) 5 Spline screw IS-M5x0x ) 6 Screw IS-M5x Instruction label (TS 40) ) 4) 5) 8 Set of instruction labels (TS 40) ) 4) 9 Instruction label (TS 40) ) 4) 6) 0 Set of instruction labels (TS 40) ) 4) Instruction label (TS 40, TS 40) ) 4) 7) Modification to be introduced : continuously Remarks ) Previous version of part no longer available from factory ) New version of part can also be used for older machines ) Previous version of part remains available for older machines 4) See "Service notes" 5) Previous version of part is replaced by Item 8 6) Previous version of part is replaced by Item 0 7) Previous version of part is replaced by Item 8 in the TS 40 and by Item 0 in the TS 40 ANDREAS STIHL AG & Co. KG, 009 Technical Documentation D/MTK-fr TI_5_009_0_0_0.fm
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS KR54, KR1654, & KR4954 Keyed Removable Mullion NOT FOR USE ON ELECTRIC OR FIRE RATED MULLIONS. This kit includes the following parts: (Not to scale) WARNING Remove key, reinstall,
More information* * 4023 KR. Step 1 Prepare the Keyed Removable Unit. Not for use on electric or fire rated removable mullions
condition. *64009-00* 64009-00 Keyed Removable Mullions 403 KR Installation Instructions Not for use on electric or fire rated removable mullions This kit includes the following parts: (Not to scale) 5/6
More information* * KR54-F, KR9854 & KR9954 Installation Instructions. Read All Warnings Before Starting Installation! Index:
*941061-00* 941061-00 Keyed Removable Mullion KR54-F, KR9854 & KR9954 Installation Instructions CLASSIFIED CLASSIFIED C Read All Warnings Before Starting Installation! Index: General Information ----------------
More informationFLEX KEY ASSEMBLY. ..._ o RAFTER ARM TUBE MAIN ARM TUBE CAP NUT CLAW HINGE
ZIP DEE Inc. 96 Crossen Ave. Elk Grove Village, IL 60007(847)437-0980 (800)338-2378 HEAD CASTING AWNING RAIL FLEX KEY ASSEMBLY..._ o GM1 Installation Instruction GMC Motorhome RAFTER ARM TUBE MAIN ARM
More informationInstallation Guide. Single-Control Kitchen Sink Faucets
Installation Guide Single-Control Kitchen Sink Faucets K-6352 K-6353 M product numbers are for Mexico (i.e. K-12345M) Los números de productos seguidos de M corresponden a México (Ej. K-12345M) Français,
More informationCOOPER FREESTANDING TUB FAUCET INSTALLATION
SKU(s): 940972 COOPER FREESTANDING TUB FAUCET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no
More informationUrea/Adblue Hose Reel
www.scintex.com.au sales@scintex.com.au Model: SHR3408 Urea/Adblue Hose Reel Product Manual Specifications Spring driven drum: for automatic rewind. Locking ratchet: to maintain the desired length of hose
More informationCONVEX Awning Instructions
CONVEX Awning Instructions IMPORTANT NOTE: Please take a few minutes to become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and will
More informationHose Reel Series L701/G701
Hose Reel Series L70/G70.0 WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal
More informationquick and easy installation guide
www.directdriveopener.com quick and easy installation guide Back 2 Front. Motor Carriage 2. C-rail. Chain. Limit stops. Slide in part (tensioner) Rail assembly Insert C-rail parts () into the connecting
More informationProduct instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E
Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E The Trimfast Ream Cutters are reliable, high performance cutters that will give you the results you need quickly
More informationStandard Awning Installation Instructions
Standard Awning Installation Instructions Important Note: Please become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and will make
More informationOWNER S TECHNICAL MANUAL
OWNER S TECHNICAL MANUAL Heavy Duty Oil Hose Reel 504200 Description Open hose reel for air, water (high or low pressure), oil or grease, depending on model. Uncoil the hose to the desired length. It can
More informationABS Model Background Stand
ABS Model Background Stand Product Overview: The completely redesigned Ravelli ABS model background stand is 10' tall by 12.3' wide. It is comprised of two tripod stands and four 3 cross bar sections and
More informationCabinet Mount Assist Lift n Lock Instructions
Cabinet Mount Assist Lift n Lock Instructions PART LIST 2 @ Gas Cylinder 1 @ Lock Bar 2 @ Rubber Sleeve (preset) 4 @ Stopper Pin (2pcs preset) 4 @ Saddle Block 8 @ 19mm Black PVC Cap 5 @ 14mm Black PVC
More informationAuxiliary 63.5l Fuel Tank Ford/Mazda Pick-up Truck 2012-Current READ ME! IMPORTANT WARNING!
Auxiliary 63.5l Fuel Tank Ford/Mazda Pick-up Truck 2012-Current ENG FTFM006 90 min READ ME! Thank you for purchasing a Front Runner Ford/Mazda Pick-Up Truck 2012 - Current Fuel Tank. Before you start,
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationSection 11 Workstation Components
1 Section Quick and easy access to parts is made possible by the wide variety of trays, bins, and framing components available from Bosch. Individual workstation grab trays, containers, and ledges place
More informationAND LOAD CANOPY RACK SPECIFICATIONS
8MAY15 INSTRUCTIONS for the LOCK AND LOAD CANOPY RACK SPECIFICATIONS and SAFE LOADING REQUIREMENTS The Lock and Load ladder carrier for Truck Caps is a rack designed to mount to the top of a pickup truck
More informationAdvantage Plus TIM-3600 Series Reel
Read the following precautions and instructions before you begin assembly or using. Failure to comply with these instructions could result in personal injury or property damage. Keep these instructions
More informationExploded views meat slicer: 800S. DEKO Holland bv B Arnhem The Netherlands
Exploded views meat slicer: 800S DEKO Holland bv. 6827 B Arnhem The Netherlands DEKO Holland bv. Recommended spare parts list Part no. Description 260-07/ 260-08/ 260-5 Switch 230 Volt / Switch 400 Volt
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS. Part # A7006
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS Part # A7006 Parts List Wobble Stopper Body Wobble Stopper Shaft Camper Bracket Lower Bracket Assembly Upper Bracket Upper Bracket Clamp 3/8 SAE Flat
More informationRETRACTABLE AWNING w/ OPTIONAL HOOD ASSEMBLY INSTRUCTIONS
Contact us @ (800)851-0865 RETRACTABLE AWNING w/ OPTIONAL HOOD ASSEMBLY INSTRUCTIONS Congratulations on your purchase of a new retractable awning. With proper installation this awning will provide years
More information31 Series. Serie 31 Série 31. Two Handle Kitchen Faucet Grifo Con Dos Manijas Para Cocina Robinet De Cuisine À Avec Deux Poignées COMPANY
31 Series Serie 31 Série 31 Two Handle Kitchen Faucet Grifo Con Dos Manijas Para Cocina Robinet De Cuisine À Avec Deux Poignées 05-06-08 EO7284A 32947-0100 Copyright 2008, Price Pfister, Inc. A COMPANY
More informationfunctionality with the necessary maintenance tools stored in a convenient built in tool box, as well as parallel handles for
GuilloMax User Manual The Guillomax has distinct features such as its unique structure and ease of cutting. It combines symmetry with functionality with the necessary maintenance tools stored in a convenient
More informationLITE Spear Awning Instructions
LITE Spear Awning Instructions IMPORTANT NOTE: Please take a few minutes to become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and
More informationAssembly TOOLS REQUIRED: 17mm and 14mm or equivalent wrenches.
Instructions for 3 Trimmer Rack, 3TR* *Patents Pending Assembly TOOLS REQUIRED: 17mm and mm or equivalent wrenches. 15 26 26 16 15 16 Attach the lower mounting brackets to the Trimmer Rack poles as shown
More informationInstallation instruction
903-CIS013-D Installation instruction 0.m Antenna LEAX Arkivator Telecom disclaims any liability for the results of improper or unsafe installation, inspection, maintenance, or removal practices. Torsgatan
More information300 ft. 5/8 Hose wagon
300 ft. 5/8 Hose wagon Model 95956 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. (Garden hose is not included).
More informationINSTALLATION GUIDELINES
IMPORTANT: To ensure this product is installed properly, you must read and follow these guidelines. The owner/user of this product must keep this information for future reference. This product must be
More informationTools. For safety and easy faucet replacement, San-Ei recommends the use of the following helpful tools:
BW-0BH INSTALLATION INSTRUCTIONS SINGLE HANDLE Kitchen Faucet Tools For safety and easy faucet replacement, San-Ei recommends the use of the following helpful tools: SAFETY GLASSES PIPE WRENCH PLIERS CHANNEL
More informationFLAIR TWO-HANDLE BATH & SHOWER FAUCET
INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN NOTES CAUTION: Risk of product damage. Remove plaster guards, valve units, and aspirator before you apply heat to yoke. Shut off the main water supply. Observe
More informationOperating Instructions
Operating Instructions Medium and High Pressure Model Numbers: RT602- RT635- RT602- RT635- RT603- RT650- RT603- RT650- RT605- RT825- RT605- RT650-SM RT802- RT835- RT425- RT803- RT402- RT435- RT625- RT403-
More informationREAD ME FIRST! IMPORTANT WARNING! ENG. Roof top tent
Roof top tent ENG TENT031 220 min READ ME FIRST! Thank you for purchasing a Front Runner Roof Top Tent. Before you start, take a moment to familiarize yourself with these Fitting Instructions and the components
More informationCassette-folding arm-awning markilux 990
Cassette-folding arm-awning markilux 990 Mounting instructions 1. Overview 1 Projection profile 2 Folding arm 3 Fabric 4 Console 5 Cassette 6 Covering cap 7 Wall bracket 2. Mounting brackets 2.1 Overview
More informationDeZURIK AM-SERIES MANUAL GEAR ACTUATOR USED ON BUTTERFLY VALVES
AM-SERIES MANUAL GEAR ACTUATOR USED ON BUTTERFLY VALVES Instruction D10501 January 2015 Instructions These instructions provide information about AM-Series Manual Actuators used on Butterfly Valves. They
More informationGT371 HEDGETRIMMER TYPE
GT371 HEDGETRIMMER TYPE 1 Introduction Exploded Drawing Bill Of Material Repair Instructions E13791 GT371-----A New Parts Wiring Diagram Main Menu 3 18 02-04 SEAN HOLDEN GT371 MANUFACTURING PLANT USTI
More informationINSTALLATION INSTRUCTIONS AND OWNER'S MANUAL AWNINGS. For trailers & motor homes with straight sides TOOLS REQUIRED
AWNINGS INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL For trailers & motor homes with straight sides TOOLS REQUIRED 1/4" electric drill Ratchet handle kit 3/8" & 7/16" socket No. 1 and No. 2 screwdriver
More informationRhino-Rack FOXWING ECO Awning 31117
Rhino-Rack FOXWING ECO Awning 31117 Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the
More informationTank. Part B, Section 1. This section covers the following unit configurations. Pump Piston Pump (E or G)
Part B, ection Model Voltage This section covers the following unit configurations. 3400V All Pump Piston Pump (E or G) Manifold Control 4-Port (A) Vista tandard (V) Vista Pattern (PC) Vista Temperature
More informationOperating Instructions
Operating Instructions Series RT Spring Driven Hose Reels Low Pressure Model Numbers: RT402-OLP RT605-OLP RT450-OLP RT835-OLP RT403-OLP RT802-OLP RT465-OLP RT850-OLP RT405-OLP RT803-OLP RT625-OLP RT450-OLPSM
More informationFactory Style Bow Kit
Installation Instructions Factory Style Bow Kit Vehicle Application: Jeep Wrangler Unlimited 2004 2006 Part Number: 55003 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question.
More informationGoBidet Bidet Attachment
GoBidet Bidet Attachment 151 Ruths Place #5 Sequim, WA 98382 Tel 1-800-681-0753 Fax +1 360-681-4029 www.go-bidet.com MODEL #2003C In this box: 1 User Manual 1 GoBidet Unit w/ mounting bracket, nut, rubber
More informationFREEDOM BUTTON KIT INSTALLATION GUIDE STEP 1
FREEDOM BUTTON KIT INSTALLATION GUIDE Installation of the Freedom Button kit is very simple and similar to the installation of a standard rear takedown pin and bolt catch latch. Before installing your
More informationGT370 HEDGETRIMMER TYPE
GT370 HEDGETRIMMER TYPE 1 Introduction Exploded Drawing Bill Of Material Repair Instructions E13791 GT370-----A New Parts Wiring Diagram Main Menu 44 18 02-04 SEAN HOLDEN GT370 MANUFACTURING PLANT USTI
More informationVEPR Round Drum Disassembly and Assembly
VEPR 12 25 Round Drum Disassembly and Assembly Required Tools ¼ Allen Wrench Flat Head Screwdriver Drum Parts List Drum Body Carousel Center Bolt Dummy Rounds Carousel Lock Spring Clear Drum Cover Step
More informationPR-429BF-600M. Bell 429 Blade Fold Kit Operations Manual
Table of Contents Table of Contents... 1 Record of Revisions... 2 References... 3 Introduction... 4 Contact Information... 4 Prerequisites... 5 First Time Use... 6 Blade Clamp Placement... 6 Blade Clamp
More informationHANDLE AND WHEEL KIT INSTALLATION
HANDLE AND WHEEL KIT INSTALLATION Select EB and EM Series Generators Honda Power Equipment Your generator is equipped with a wheel kit and folding handle kit for easy transport and convenient storage.
More informationVISIT OUR WEBSITE: OR CALL US TOLL FREE AT
Model #710 WATH THE VIEO Owner s Manual VISIT OUR WEBSITE: WWW.LIBERTYGARENPROUTS.OM OR ALL US TOLL FREE AT 1-866-820-5805 LIBERTY GAREN PROUTS, IN. 1161 SOUTH PARK RIVE, KERNERSVILLE N 27284 IMPORTANT:
More informationRetractable Hose Reel
Retractable Hose Reel installation and Operation Please read before use We recommend keeping these instructions for future reference Hose Reel must be mounted before use Keep the hose retracted when not
More information300 Model 870 Four Wheel Hose Cart Owner s Manual
300 Model 870 Four Wheel Hose Cart Owner s Manual IMPORTANT: READ THE OWNER S MANUAL BEFORE ASSEMBLING TOOLS REQUIRED: TWO ADJUSTABLE WRENCHES; HAND PUMP Estimated assembly time: 30 minutes PARTS LIST
More informationINSTALLATION INSTRUCTIONS TOWNSEND
INSTALLATION INSTRUCTIONS TOWNSEND.00 DECK MOUNT BATH FILLER.0 Thank you for selecting American Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-please
More informationRAFTER VI. Installation and Operation CAREFREE WITH AUTOMATIC AWNING SUPPORT. RV Accessory PRODUCT OVERVIEW
CAREFREE RAFTER VI RV Accessory WITH AUTOMATIC AWNING SUPPORT Installation and Operation PRODUCT OVERVIEW The gives the awning user the ability to easily tighten the center fabric when the awning is extended.
More informationItem #: BTOT Assembly Instructions
Item #: BTOT Assembly Instructions For our most current instructions, to request missing, lost or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com
More informationINSTRUCTIONS INSTALLATION UNIVERSAL SERIES PATIO AWNING HARDWARE , , ,
RECORD THIS INFORMATION FOR FUTURE REFERENCE: Model Number Serial Number Hardware Model Number Hardware Serial Number Date Purchased Retailer / Qualified Installer INSTALLATION INSTRUCTIONS UNIVERSAL SERIES
More information--- BIG LEAGUE BATTING CAGE ---
--- BIG LEAGUE BATTING CAGE --- BGLC-7500 Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev-B Page 1 of 22 IMPORTANT NOTICE: 1. BEFORE
More informationAssembling & Fitting Instruction August 2015
Assembling & Fitting Instruction August 2015 Wave Curtain Heading System Silent Gliss 6010, 6020, 6100, 6103, 6290, 6380, 6465 Silent Gliss 3840, 6120 Silent Gliss 5090, 5200, 5400 Silent Gliss 5100, 5600
More informationWIDESPREAD LAVATORY MODELS WITH HI-ARC SPOUT
5951, 5961, 5981, 5983, 5993 SERIES MT122B INSTALLATION INSTRUCTIONS THESE INSTRUCTIONS MUST BE LEFT WITH HOMEOWNER WIDESPREAD LAVATORY MODELS WITH HI-ARC TRADITIONAL CROSS NOTE: Handle Inserts are not
More informationInstallation Instructions for Wall Mount, Deck Mount and Pre-rinse Faucets
Installation Instructions for Wall Mount, Deck Mount and Pre-rinse Faucets SAVE FOR END USER ELKAY 2222 CAMDEN COURT OAK BROOK, IL 60523 USA WALL MOUNT ASSEMBLY General Instructions Turn off the water
More information1946 READ AND SAVE THESE INSTRUCTIONS!
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Quarter Round Awning Installation
More informationFORCE 10 MARINE BARBEQUES
FORCE 10 MARINE BARBEQUES PROPANE MODELS Model 3500 % Large Propane Model 3550 % Small Propane OWNER S MANUAL AND WARRANTY FORCE 10 MARINE LTD. 23080 Hamilton Road, Richmond, B.C. Canada V6V 1C9 Telephone
More informationJARVIS. Model 70 Airsnip Air Powered Scissors
Air Powered Scissors EQUIPMENT SELECTION... Ordering No. Airsnip Model 70... 4019009 Air Filter/Regulator/Lubricator.. 3022003 Balancer... 1350084 Power--Pak (250 PSI)... 4026016 TABLE OF CONTENTS... Page
More informationOletto Single Lever Commercial Style Kitchen Faucet
INSTALLATION MANUAL Oletto Single Lever Commercial Style Kitchen Faucet KPF-2630 www.kraususa.com I toll free: 1.800.775.0703 I 2014-2015 Kraus USA Inc. I RV. March 30, 2017 Thank you for your purchase
More information7. Do not dispose of the packaging immediately.the package insert contains a template for mounting the slide bar A/Rev01 G1/2" G1/2" G1/2"
INSTALLATION INSTRUCTIONS Magnetic Slide Shower 550 552 BEFORE YOU BEGIN MAGNETIC SLIDE SHOWER All information is based on the latest product information available at the time of publication. Kohler Co.
More informationSolera Classic Awning OEM INSTALLATION MANUAL
Solera Classic Awning OEM INSTALLATION MANUAL TABLE OF CONTENTS System and Safety Information 2 Preparation 3 Resources Required 3 Installation 3 Installing the Awning Rail (If Necessary) 3 Assembling
More information, & Series Nested Hardware
RECORD THIS INFORMATION FOR FUTURE REFERENCE BEFORE INSTALLING THE UNIT: Model Number Serial Number Date Purchased Place of Purchase USA SERVICE OFFICE Dometic Corp. 509 So. Poplar St. LaGrange, IN 46761
More informationThomas Scientific Swedesboro, NJ U.S.A.
Thomas Scientific Swedesboro, NJ 08085-0099 U.S.A. Wiley Laboratory Mill, Model 4 3375-E10 (115 V, 50/60 HZ) USE AND CARE OF CATALOG NUMBER: 3375-E10 Wiley Laboratory Mill, Model 4 (115 V, 50/60 HZ) UNPACKING
More informationCHANGING YOUR LANDSCAPE SINCE 1945 OWNER S MANUAL. Tow Hitch Replacement Kit For Rough Cut Trailcutters. Starting Serial # L
CHANGING YOUR LANDSCAPE SINCE 1945 OWNER S MANUAL Tow Hitch Replacement Kit For Rough Cut Trailcutters 21100 Starting Serial # L118-023001 Tools Required: Wrench/Socket Qty. Size (1) 1-1/8 (1) 1-1/16 (2)
More informationASSEMBLY & CARE INSTRUCTIONS
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 3 9 Part No. FT3711 - on road FT3923 - off road OPTIONAL SUNROOM Wall and floor kit Part No. FT3723 - on road FT39 - off road OPTIONAL SPARE ROOM Roof,
More informationVanagon Ladder Kit Assembly & Installation Instructions
Rocky Mountain Westy Vanagon Ladder Kit Assembly & Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Vanagon Ladder Kit. We pride ourselves in the products we develop
More informationNEWMAR SERVICE SCHOOL
NEWMAR SERVICE SCHOOL TRAINING INFORMATION GUIDELINE FOR FEBRUARY 2013 OUR PRODUCTS: NOVA DUAL PITCH AWNING G-2000/ G-1500 2 P a g e G-2085 G-5000 3 P a g e G-LINKS 4 P a g e NOVA/ G-2000/ G-1500 BASIC
More informationImportant Information
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the crossbars are installed in the correct locations. Check the contents
More informationNM-11 INSTRUCTION MANUAL WARNING!! TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND THIS INSTRUCTION MANUAL. ORIGINAL INSTRUCTIONS
NM-11 INSTRUCTION MANUAL WARNING!! TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND THIS INSTRUCTION MANUAL. ORIGINAL INSTRUCTIONS Date of purchase:... NM-11 manual.en 05/2017 - SSM Produkt
More informationTC42 TRANQUILITY BURNER KIT INSTRUCTIONS
IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER These instructions are supplementary to the Installation and Operating Instructions supplied with the fi replace and should be kept together.
More informationTCWS.38NG03.C BLACK DIAMOND BURNER KIT INSTRUCTIONS
IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER These instructions are supplementary to the Installation and Operating Instructions supplied with the fireplace and should be kept together.
More informationOtter Pro X-Over Lodge Installation and Set-Up Instructions
Otter Pro X-Over Lodge Installation and Set-Up Instructions Otter Pro X-Over Lodge Fits Magnum Otter II & Pro Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro X-Over Lodge
More informationImportant! Read all of these instructions before assembling or riding the glider. For questions or help please call Glide Bikes at
Go Glider Manual Congratulations on your purchase of the Go Glider! Your glider is designed for years of nearly carefree use by your child. These instructions include how to set up your glider and maintenance
More informationASSEMBLY & CARE INSTRUCTIONS. 7 x4 TRAILER TENT SERIES 4 9. OPTIONAL SUNROOM Wall and floor kit. OPTIONAL SPARE ROOM Roof, wall and floor kit
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 9 Part No. TM709 OPTIONAL SUNROOM Wall and floor kit Part No. TM723 OPTIONAL SPARE ROOM Roof, wall and floor kit Part No. TM76 Please keep these instructions
More informationS E L E C T I O N. Abdominal Crunch. User manual
and S E L E C T I O N T H E S T R E N G T H E V O L U T I O N User manual and and The identification plate of the and manufacturer, affixed along side the seat on the frame of the weight stack, gives the
More informationInstallation and User s Manual 12 x 10 MOTORIZED AWNING
12 x 10 MOTORIZED AWNING Installation and User s Manual 12 x 10 MOTORIZED AWNING 088-1763-0 Stop Please read and understand this manual before any assembly or use of this product. Before beginning assembly
More informationRETRACTABLE PATIO SHADE AWNING Patio Awning Guide-10ft. x12ft.(proj. X Width) Model: APR ***/APR (version: GEN2-V1)
Page 1 of 14 RETRACTABLE PATIO SHADE AWNING Patio Awning Guide-10ft. x12ft.(proj. X Width) Model: APR-101012***/APR-60021012 (version: GEN2-V1) WARNING: DO NOT CUT THE PLASTIC ZIP TIES ON THE AWNING EXTENSION
More informationMANDATORY BULLETIN No. EV a (ZBEV a) SPORTSTAR 004 a (ZBSPORTSTAR-004a)
Issues MANDATORY BULLETIN No. EV-97 009 a (ZBEV-97-009a) SPORTSTAR 004 a (ZBSPORTSTAR-004a) 1. CONCERNING TO : Lock of the wide tilting canopy installed on the SPORTSTAR airplanes and on some of the EV-97
More informationEaton ET Hydraulic Hose Saw INSTRUCTION MANUAL
Eaton ET9100-07-110 Hydraulic Saw INSTRUCTION MANUAL INSTRUCTION MANUAL Eaton ET9100-07-110 Hydraulic Saw Table of Contents Introduction... 3 Old Method... 3 New Eaton Method... 3 Operation... 4 Operation
More informationINSTRUCTION MANUAL ALEKO RETRACTABLE AWNING
INSTRUCTION MANUAL for ALEKO RETRACTABLE AWNING www.alekoproducts.com FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY! 1 Important Safety Precautions WARNING NOTE: FOR PERSONAL SAFETY,
More informationaccidents which arise due to non-observance of these instructions and the safety information herein. CAUTION:
AUTO REWIND HOSE REEL Model: 7640 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This
More informationInstallation Instructions Traditional Awnings in a box Classic Awnings in a Box
Installation Instructions Traditional Awnings in a box Classic Awnings in a Box Basic Tools Required (not included) Tape Measure & Pencil Level Phillips Screwdriver Drill with ¼ bit (Cement or Masonry
More information33100 LH - Batwing Awning RH - Batwing Awning
33100 LH - Batwing Awning 33200 RH - Batwing Awning 1. Check Part No./Kit is correct 3. Fit roof rack accessory 2. Read through instruction before installing 4. Check and recheck all fasteners are secure
More informationSOLHARO ASSEMBLY & INSTALLATION INSTRUCT IONS
A. Introduction: SOLHARO ASSEMBLY & INSTALLATION INSTRUCT IONS Rev. 01/30/2012 The Solharo is an external, retractable, tensioned sun shading system designed to fit over a sunroom or wood pergola. The
More informationSHOWER CONVERSION KIT WITH HAND SHOWER
SHOWER CONVERSION KIT WITH HAND SHOWER BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage
More informationInsruction manual Dukki
Insruction manual Dukki Introduction Pg. 1 Product description Pg. 2 3 Assembly and disassembly Pg. 4 Installation and adjustment Pg. 5 12 Maintenance Pg. 13 Parts Pg. 14-17 INDEX 1. Introduction 1 2.
More informationREAD ME! IMPORTANT WARNING! ENG. Quick Release Tent Mount Kit
Quick Release Tent Mount Kit ENG TBMK008 READ ME! Thank you for purchasing a Front Runner Quick Release Tent Mount Kit. Before you start, take a moment to familiarize yourself with the Fitting Instructions
More informationOtter Pro XT Cabin Installation and Set-Up Instructions
Otter Pro XT Cabin Installation and Set-Up Instructions Otter Pro XT Cabin Fits Medium Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro XT Thermal Cabin
More informationALEKO Victoria Series Retractable Awning Instructions for Installation and Operation
www.alekoproducts.com ALEKO Victoria Series Retractable Awning Instructions for Installation and Operation PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE! The owner s manual includes assembly and operating
More informationReverse Osmosis system 50 GPD Instruction manual EN
Reverse Osmosis system 50 GPD Instruction manual EN Contents 1. Unpacking 2. Scope of supply 3. Insertion of the membranes 4. Connecting the lines 5. Installation 6. First commissioning 7. Consumables
More informationSwagelok Thermoplastic Hose Hand Swager User s Manual
Swagelok Thermoplastic Hose Hand Swager User s Manual Thermoplastic Hose Hand Swager User s Manual Contents Hand Swager Components....................... 2 Setup Swager.......................................
More informationAuto Rewind Hose Reel 10M / 20M / 30M Models
Auto Rewind Hose Reel 10M / 20M / 30M Models Instruction Manual 10M / 20M / 30M Auto Rewind Hose Reel Installation, Hose Replacement and Troubleshooting Guide Product Codes: 1110H / 1120H / 1130H Models
More informationSH, MP, HP, EZ-SH, EZ-MP, EZ-HP Series Design Features & Benefits COXREELS. SH, MP, HP, EZ-SH, EZ-MP, & EZ-HP Series Design Features
COXREELS SH, MP, HP, EZ-SH, EZ-MP, & EZ-HP Series Design Features The following are features and benefits of our Standard Heavy Duty and EZ Coil TM Series Reel 1. GUIDE ARM: The Coxreels guide arm is stamped
More informationRoller Bar End Cap (w/round Drive Shaft) Replacement Instructions for Vista and Motorized Awnings * Helpers needed *
RETRACTABLE AWNINGS For Technical Support visit us at www.sunsetter.com/ownerscorner or Call Toll Free 800-670-7071 Fax 877-224-4944 Roller Bar End Cap (w/round Drive Shaft) Replacement Instructions for
More informationRH BABY&CHILD AVALON TWIN OVER TWIN BUNK BED INSTRUCTIONS
RH BABY&CHILD AVALON TWIN OVER TWIN BUNK BED INSTRUCTIONS Made in Vietnam Distributed in the U.S.A. by: Restoration Hardware Baby & Child 11640 Harrel St. Suite B Mira Loma, CA 91752 www.rhbabyandchild.com
More informationModel 698/ and Model in 1 Hose Reel Owner s Manual
Model 698/694 200 and Model 706 100 4 in 1 Hose Reel Owner s Manual 698/694 706 VISIT OUR WEBSITE: WWW.LIBERTYGARDENPRODUCTS.COM OR CALL US TOLL FREE AT 1-866-820-5805 LIBERTY GARDEN PRODUCTS, INC. 500
More information