CHANGING YOUR LANDSCAPE SINCE 1945 OWNER S MANUAL. Tow Hitch Replacement Kit For Rough Cut Trailcutters. Starting Serial # L
|
|
- Franklin Watkins
- 5 years ago
- Views:
Transcription
1 CHANGING YOUR LANDSCAPE SINCE 1945 OWNER S MANUAL Tow Hitch Replacement Kit For Rough Cut Trailcutters Starting Serial # L Tools Required: Wrench/Socket Qty. Size (1) 1-1/8 (1) 1-1/16 (2) 15/16 For Questions, Comments, or Parts Please Call: (2) 9/ Or Visit: REV
2 REFER TO OWNER S MANUAL OF MOWER FOR SAFETY PRECAUTIONS INSTALLATION INSTRUCTIONS: (1) Unpack your kit and become familiar with each component. Ensure that the correct quantity of each component noted in the parts list is present. Contact customer service if any components are missing ( ). Read the installation instructions thoroughly before you begin. (2) Begin your installation by removing the previous tow hitch assembly from your current trail mower by removing the fasteners (items 11 & 27 in the parts list) used to secure the Hitch Frame to the Mower Deck. Note: Alternate fasteners may be present on some models. Remove the entire hitch and set aside. None of the parts from this original hitch will be needed to attach your new replacement hitch. Configuration A (Figure 3A) 3) Attach the side arms of the hitch mount frame [item 2] to the side walls of your mower deck. Secure using (4) 3/8-16 bolts and (4) 3/8-16 Nyloc nuts [items 11 & 27]. Securely tighten these fasteners. 4) Slide machine bushing [item 19] onto rod at the base of the pivot assembly [item 1]. Apply lubricating grease and slide large bolt attached to the pivot assembly through the large hole in the hitch mount frame [item 2]. Using (1) 1 flat washer, (1) 1 Belleville washer (concave face up) & (1) 1-8 Lock nut [items 20, 24 & 7], secure pivot assembly to the hitch frame mount plate. Tighten Nyloc nut as tight as possible while still being able to rotate the pivot assembly. If you cannot rotate pivot assembly to achieve different offsets, loosen large nut until movement is achieved. 5) Using (1) 3/4-10 bolt, (2) 3/4 14 GA washers, (1) 3/4 SAE washer, and (1) 3/4-10 Nyloc Nut [items 25, 28, 14, & 13] connect Pivot Bracket Assembly to Hitch Bar Lower Arm. Ensure the thin 3/4 washer goes inbetween the Pivot Bracket Assembly to Hitch Bar Lower Arm on the inside of the Pivot Bracket. Apply lubricating grease inside of Hitch Bar Lower Arm pivot tube before assembly. Tighten until there is no sideways movement of the Hitch Bar inside the Pivot Bracket, but the Hitch Arm should still pivot up and down freely. Do not over tighten! 6) Using (1) 3/4-10 bolt, (2) 3/4 washers and (1) 3/4-10 Nyloc nut [items 12, 14 & 13] connect the fan hitch bar [item 17] to the hitch tube [item 16] and apply lubricating grease. Tighten until nut is snug against hitch plate. Do not over tighten! 7) Insert clevis pin [item 18] into the hole in the hitch bar offset fan and through the hitch bar. Page 6 shows pin locations to achieve offset positions. 8) Slide 2 ball coupler [item 8] over hitch tube [item 17]. Fasten ball coupler to the hitch tube using (2) 3/8-16 bolt, (4) 3/8 washers & (2) 3/8 Nyloc nuts [items 9, 10 & 11]. 9) Attach 2 ball coupler to a 2 tow ball located on your tow vehicle. 10) Installation is complete! Refer to page 5 for offset & height adjustments. Configuration B (Figure 3B) 3) Attach the side arms of the hitch mount frame [item 2] to the side walls of your mower deck. Secure using (4) 3/8-16 bolts and (4) 3/8-16 Nyloc nuts [items 11 & 27]. Securely tighten these fasteners. 4) Slide machine bushing [item 19] onto rod at the base of the pivot assembly [item 1]. Apply lubricating grease and slide large bolt attached to the pivot assembly through the large hole in the hitch mount frame [item 2]. Using (1) 1 flat washer, (1) 1 Belleville washer (concave face up) & (1) 1-8 Nyloc nut [items 20, 24 & 7], secure pivot assembly to the hitch frame mount plate. Tighten Nyloc nut as tight as possible while still being able to rotate the pivot assembly. If you cannot rotate pivot assembly to achieve different offsets, loosen large nut until movement is achieved. 5) Using (1) 3/4-10 bolt, (2) 3/4 14 GA washers, (1) 3/4 SAE washer, and (1) 3/4-10 Nyloc Nut [items 25, 28, 14, & 13] connect Pivot Bracket Assembly to Hitch Bar Lower Arm. Ensure the thin 3/4 washer goes in between the Pivot Bracket Assembly to Hitch Bar Lower Arm on the inside of the Pivot Bracket. Apply lubricating grease inside of Hitch Bar Lower Arm pivot tube before assembly. Tighten until there is no sideways movement of the Hitch Bar inside the Pivot Bracket, but the Hitch Arm should still pivot up and down freely. Do not over tighten! 6) Slide 2 ball coupler [item 8] over hitch tube [item 16]. Fasten ball coupler to the hitch tube using (2) 3/8-16 bolt, (4) 3/8 washers & (2) 3/8 Nyloc nuts [items 9, 10 & 11]. 7) Attach 2 ball coupler to a 2 tow ball located on your tow vehicle. 8) Installation is complete! Refer to page 5 for offset & height adjustments. 2
3 Hitch Configurations Your new hitch is designed to be assembled in one of two configurations. Either configuration (see page 3) will work with any of the hitch positions (see page 6). However, to maximize turn radius and functionality of the mower, Swisher recommends assembly Configuration A for all hitch positions and assembly Configuration B for hitch for POSITION 1 only (Figure 6A). Configuration B will limit tire clearance when the mower is in an offset position. EXPLODED VIEW CONFIGURATION A: (Figure 3A) EXPLODED VIEW CONFIGURATION B: (Figure 3B) 3
4 PARTS LIST: ITEM QTY. PART # DESCRIPTION * Weldment - Pivot Bracket Assembly * Weldment - Hitch Mount; RC Compression Spring 4 1 NB126 1/8" X 1" Cotter Pin Washer - Flat, N1/2"-12Ga Pin - Pivot Latch Nut - 1"-8 Stover Lock " Ball Coupler 9 2 NB150 Bolt - Hex, 3/8-16 X 3" 10 4 NB272 3/8 Sae Washer 11 2 NB182 3/8-16 Nyloc Nut Bolt - Hex, 3/4-10 X 3 3/4" Nut - 3/4-10 Nylon Insert Lock ZP 14 3 NB146 3/4" Sae Flat Washer Nut - 5/8-11 Nylon-Insert Lock ZP * Weldment - Hitch Bar Lower Arm * Weldment - Upper Hitch Arm Assembly Pin - Clevis 3/8 X 3 ZP Bushing - Machine; 1" ID 20 1 NB569 Washer - Uss Flat, Ø1" X Ø2.5" Plug - 1 1/2" X 2", End Cap 22 2 NB667 Bolt - Hex, 5/8-11 X 2 1/2" Top Link - Cat 0 W/ Adjusting Rod 24 1 NB738 Belleville Washer Bolt - Hex, 3/4-10 X 4 1/2" 26 1 NB127 #3 Hair Pin (A155H) 27 4 NB618 Bolt - Hex, 3/8-16 X 1 1/4 GR5 ZP 28 2 NB179 3/4 ID X 1 1/4 OD 18 GA Washer When ordering replacement parts *USE PAINT CODE: TC=RED, TK=BLACK 4
5 DECK LEVELNG INSTRUCTIONS: (1) Refer to your mower s owner manual for mower deck height adjustment information. Once the mower height has been adjusted, it is important to level out the mower s deck. (2) You will use the top link [item 23] to level the deck after the height has been adjusted. The top link has an integrated adjustment rod to assist in turning the body and to make the top link extend or contract. (3) Ensure the jam nut is loosened on the threads at one end of the top link body. To loosen this nut without a tool, simply turn the top link in the direction to thread it away from the nut (Figure 6A). The nut will now be loosened and should be threaded away by hand from the top link body as to not interfere with the adjustment process. (4) To lower the front of the mower deck, simply turn the top link in the direction needed to draw the threads into the top link body. This will lower the front of the mower deck to achieve a level deck. (5) To raise the front of the mower deck turn the top link in the direction needed to push the threads out from the top link body. This will raise the front of the mower deck to achieve a level deck. OFFSET INSTRUCTIONS: (Refer to page 6) (1) It is recommended to offset mower while still attached to the tow vehicle. (2) Locate spring pin [item 6] on the pivot assembly. Pull pin upward and rotate to rest the pin into the notch (Figure 6D). Move Mower and hitch bar in the direction of desired offset. Once the offset position is reached, remove spring pin from notch and allow it to lock into place (Figure 6E). You may need to move the hitch bar slightly to allow the spring pin to find the hole and lock into place. (3) Locate clevis pin [item 18] in the fan pivot on the tow bar. Remove the pin to allow the tow bar to pivot. Replace the clevis pin into the matching hole location as selected in step (1). The short tow bar section should now be parallel with the mower deck. 5
6 RECOMMENDED HITCH CONFIGURATIONS AND POSITIONS (Figure 6A) (Figure 6B) (Figure 6C) (Figure 6D) Unlocked 6 (Figure 6E) Locked
7 Troubleshooting Problem Possible Issue Possible Solution Hitch bar fan pivot [item 17] will not swivel. Spring pin [item 6] will not disengage. Hitch bar will not pivot at frame base. Tow bar hits tow vehicle tire. (1) The center bolt is too tight. (2) Clevis pin is engaged. (3) Debris is lodged in hitch bar. (1) Pin is wedged in the lock position. (1) Nut [item 7] is too tight on pivot rod [item 1]. (1) The tow bar center pivot is not adjusted properly. (2) Hitch is in Configuration B (1) Loosen the nut on the bottom of hitch bar until the the bar swivels freely. (2) Remove clevis pin from pivot fan holes. (3) Remove any debris from hitch bar. (1) Move hitch bar back and forth until pin is freed. (1) Slighty loosen nut on bottom of pivot base until hitch pivots freely. (1) Ensure the hitch bar fan is in the matching offset position as the base pivot offset. (2) Assemble hitch into Configuration A Hitch Bar Maintenance: (1) Apply lubricating grease to all moving parts regularly. (2) Check nut tightness before each use. (3) Refer to your mower s owner manual for mower maintenance schedule. IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE THE CUTTER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT YOU ARE NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER PROBLEMS. 7
8 LIMITED WARRANTY The manufacturer s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions: 1. Limitation This warranty applies only to products which have been properly assembled, adjusted, and operated in accordance with the instructions contained within this manual. This warranty does not apply to any product of Swisher that has been subject to alteration, misuse, abuse, improper assembly or installation, shipping damage, or to normal wear of product. 2. Exclusions Excluded from this warranty are normal wear, normal adjustments, and normal maintenance. In the event you have a claim under this warranty, you must return the product to an authorized service dealer. All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this warranty, please contact us toll-free at The model number, serial number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the product will be needed before any warranty claim can be processed. THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of
UTV SNOW FORCE TM PUSH TUBE KIT OWNER S MANUAL
1701 38TH AVE W PO BOX 257 SPENCER, IA 51301 PHONE: 712-262-4191 FAX: 712-262-0248 SERVICE: 800-841-2222 E-MAIL: ccac@cyclecountry.com www.cyclecountry.com UTV SNOW FORCE TM PUSH TUBE KIT OWNER S MANUAL
More information42" SNOW BLADE. Owner's Manual. Model No Safety Assembly Operation Maintenance Parts
Owner's Manual 42" SNOW BLADE Model No. 486.24443 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Safety Assembly Operation Maintenance Parts
More informationREAD ME! IMPORTANT WARNING! ENG. Quick Release Tent Mount Kit
Quick Release Tent Mount Kit ENG TBMK008 READ ME! Thank you for purchasing a Front Runner Quick Release Tent Mount Kit. Before you start, take a moment to familiarize yourself with the Fitting Instructions
More informationUTV BLADE MOUNT HARDWARE
1701 38TH AVE W PO BOX 257 SPENCER, IA 51301 PHONE: 712-262-4191 FAX: 712-262-0248 SERVICE: 800-841-2222 E-MAIL: ccac@cyclecountry.com UTV BLADE MOUNT HARDWARE For the KUBOTA RTV900 OWNER S MANUAL MODEL
More information* * 4023 KR. Step 1 Prepare the Keyed Removable Unit. Not for use on electric or fire rated removable mullions
condition. *64009-00* 64009-00 Keyed Removable Mullions 403 KR Installation Instructions Not for use on electric or fire rated removable mullions This kit includes the following parts: (Not to scale) 5/6
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS KR54, KR1654, & KR4954 Keyed Removable Mullion NOT FOR USE ON ELECTRIC OR FIRE RATED MULLIONS. This kit includes the following parts: (Not to scale) WARNING Remove key, reinstall,
More informationAssembly TOOLS REQUIRED: 17mm and 14mm or equivalent wrenches.
Instructions for 3 Trimmer Rack, 3TR* *Patents Pending Assembly TOOLS REQUIRED: 17mm and mm or equivalent wrenches. 15 26 26 16 15 16 Attach the lower mounting brackets to the Trimmer Rack poles as shown
More information1000M MANUAL Signature Series Slicer OPERATORS MANUAL
1000M MANUAL Signature Series Slicer OPERATORS MANUAL Persons under age 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. Of Labor Employment Standards Administration
More informationINSTRUCTION SHEET DETHATCHER KIT. STS-422LX LPSTS-42JD Assembly Installation Operation Repair Parts L-1660-D. Visit us on the web!
INSTRUCTION SHEET DETHATCHER KIT MODEL: DK-422LX FOR USE WITH SWEEPER MODEL: STS-422LX LPSTS-42JD Assembly Installation Operation Repair Parts For use with Riders and Lawn/Garden Tractors For the latest
More informationfront runner READ ME! IMPORTANT WARNING! ENG Foxwing Awning Brackets
front runner Foxwing Awning Brackets ENG RRAC0 READ ME! Thank you for purchasing Front Runner Foxwing Awning Brackets. Before you start, take a moment to familiarize yourself with the Fitting Instructions
More informationPARTS BOOK FLAIL HEADS 90 REAR 3PT HITCH MOUNT
PARTS BOOK FLAIL HEADS 90 REAR 3PT HITCH MOUNT 5.0.8 DIAMOND MOWERS, LLC 350 E 60 th St. North Sioux Falls, SD 5704 FOR WARRANTY CALL DIAMOND MOWERS DIRECT: 888-960-0364 OUR TECHNICIANS WILL DIAGNOSE YOUR
More informationaccidents which arise due to non-observance of these instructions and the safety information herein. CAUTION:
AUTO REWIND HOSE REEL Model: 7640 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS. Part # A7006
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS Part # A7006 Parts List Wobble Stopper Body Wobble Stopper Shaft Camper Bracket Lower Bracket Assembly Upper Bracket Upper Bracket Clamp 3/8 SAE Flat
More information* * KR54-F, KR9854 & KR9954 Installation Instructions. Read All Warnings Before Starting Installation! Index:
*941061-00* 941061-00 Keyed Removable Mullion KR54-F, KR9854 & KR9954 Installation Instructions CLASSIFIED CLASSIFIED C Read All Warnings Before Starting Installation! Index: General Information ----------------
More informationFactory Style Bow Kit
Installation Instructions Factory Style Bow Kit Vehicle Application: Jeep Wrangler Unlimited 2004 2006 Part Number: 55003 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question.
More informationREAD AND SAVE THESE INSTRUCTIONS! EasyAwn Spear Awning Installation
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Spear Awning Installation
More informationSolera Classic Awning
Solera Classic Awning OWNER'S MANUAL Page 1 Table of Contents System and Safety Information 2 Operation 3 Extending the Awning 3 Optional Car Port Position 3 Retracting the Awning 3 Fabric Replacement
More information1946 READ AND SAVE THESE INSTRUCTIONS!
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Quarter Round Awning Installation
More informationShut off combine and remove key before installing the hopper extension. Make sure the combine is on a level surface. Engage parking brake.
ASSEMBLY INSTRUCTIONS CASE IH 5088, 6088/7088, 7010/8010 & 7120/8120/9120 Series NEW HOLLAND CR STD Series Combines (Large) big top 26301(service only), 29976 (service only), 53408, 53543 & 54274 The Crary
More informationSTOP BOX SCRAPER/GRADER BLADE. Owner's Manual. Model No Safety Assembly Operation Maintenance Parts
Owner's Manual STOP BOX SCRAPER/GRADER BLADE Model No. 486.242411 DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 CAUTION: Before using this product, read this manual
More informationSPIRAL SLICER Instruction Manual Model #5280 & 5280M. Part No Revised Feb. 2010
SPIRAL SLICER Instruction Manual Model #5280 & 5280M Part No. 82876 Revised Feb. 2010 SAFETY PRECAUTIONS INSTALLATION INSTRUCTIONS Inspection of Shipment: 5280 & 5280M SPIRAL SLICER Unpack all cartons
More informationRAFTER VI. Installation and Operation CAREFREE WITH AUTOMATIC AWNING SUPPORT. RV Accessory PRODUCT OVERVIEW
CAREFREE RAFTER VI RV Accessory WITH AUTOMATIC AWNING SUPPORT Installation and Operation PRODUCT OVERVIEW The gives the awning user the ability to easily tighten the center fabric when the awning is extended.
More informationHARD DOOR UPGRADE KIT
RV Accessories OWNER'S MANUAL HARD DOOR UPGRADE KIT FOR ADD-A-ROOM & BREEZEWAY SCREEN ROOMS THIS MANUAL SUPPLEMENTS THE ADD-A-ROOM INSTRUCTIONS TABLE OF CONTENTS First Time Assembly... 2 Assembling the
More informationCabinet Mount Assist Lift n Lock Instructions
Cabinet Mount Assist Lift n Lock Instructions PART LIST 2 @ Gas Cylinder 1 @ Lock Bar 2 @ Rubber Sleeve (preset) 4 @ Stopper Pin (2pcs preset) 4 @ Saddle Block 8 @ 19mm Black PVC Cap 5 @ 14mm Black PVC
More informationMAX Series 9514 OPERATOR S MANUAL
MAX Series 9514 OPERATOR S MANUAL Persons under age 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. Of Labor Employment Standards Administration Fact Sheet
More informationEEZI - AWN series 1000 / 2000 Awning bracket
EEZI - AWN series 1000 / 2000 Awning bracket RRAC063 INSTALL TIME: 15 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
More informationREAD ME FIRST! IMPORTANT WARNING! ENG. Roof top tent
Roof top tent ENG TENT031 220 min READ ME FIRST! Thank you for purchasing a Front Runner Roof Top Tent. Before you start, take a moment to familiarize yourself with these Fitting Instructions and the components
More informationYAMAHA WINCH MOUNT KIT. Installation Instructions KIT NUMBER:
YAMAHA WINCH MOUNT KIT Installation Instructions KIT NUMBER: 25-5160 CUSTOMER MUST RECEIVE A COPY OF THIS INSTRUCTION MANUAL AT TIME OF SALE 2005 CYCLE COUNTRY ACCESSORIES CORP. Rev. 2 9/22/06 Please Note:
More informationREAD AND SAVE THESE INSTRUCTIONS! EasyAwn Standard Awning Installation
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Standard Awning Installation
More informationModel 698/ and Model in 1 Hose Reel Owner s Manual
Model 698/694 200 and Model 706 100 4 in 1 Hose Reel Owner s Manual 698/694 706 VISIT OUR WEBSITE: WWW.LIBERTYGARDENPRODUCTS.COM OR CALL US TOLL FREE AT 1-866-820-5805 LIBERTY GARDEN PRODUCTS, INC. 500
More informationWenger Corporation 2014 Printed in USA 05/14 Part #049B015-09
Assembly Instructions Tuba Tamer Contents Important User Information...........................2 Replacemant Parts List..............................3 Assembly.........................................4
More informationKAWASAKI MULE 610 WINCH MOUNT KIT. Owner s Manual
1701 38TH AVE W PO BOX 257 SPENCER, IA 51301 PHONE: 712-262-4191 FAX: 712-262-0248 SERVICE: 800-841-2222 E-MAIL: ccac@cyclecountry.com KAWASAKI MULE 610 WINCH MOUNT KIT Owner s Manual MODEL NUMBER: 25-2200
More informationPIONEER LITE PATIO AWNING OWNER'S MANUAL
A Manual Crank Operated Awning RV OWNER'S MANUAL TABLE OF CONTENTS Introduction... 2 Operating the Awning... 3 To Open the Awning:... 3 Adjusting the Pitch... 4 Rain Release Setting... 4 Setting the Arms
More informationNORDIC PLOW TORO Time Cutter Plow PLOW KIT for TORO Time Cutter SW developed by Nordic Plow
NORDIC PLOW TORO Time Cutter Plow PLOW KIT for TORO Time Cutter SW4200 49 developed by Nordic Plow TIME CUTTER ATTACHMENT ASSEMBLY TIPS... DANSK...1 ENGLISH... 3 NORSK... 19 FRANCAIS...12 SVENSKA...20
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS D3109. REVISED vers10 BY: DSK 1/9/2015 TECH SUPPORT (800)
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS D3109 REVISED vers10 BY: DSK 1/9/2015 TECH SUPPORT (800) 246-8132 AFTER INSTALL, PLEASE GIVE THIS BOOKLET TO YOUR CUSTOMER 1 Warnings Truck Bed and Camper
More information300 ft. 5/8 Hose wagon
300 ft. 5/8 Hose wagon Model 95956 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. (Garden hose is not included).
More informationRESIDENTIAL PATIO AWNING
INSTALLATION & OWNER'S MANUAL RESIDENTIAL PATIO AWNING Residential A MANUAL CRANK PATIO AWNING FOR RESIDENTIAL HOMES 052592-001r1 Printed in USA April, 2013 TABLE OF CONTENTS Product Overview... 1 Component
More informationNORDIC PLOW TORO Time Cutter Plow PLOW KIT for TORO Time Cutter SW developed by Nordic Plow
NORDIC PLOW TORO Time Cutter Plow PLOW KIT for TORO Time Cutter SW4200 49 developed by Nordic Plow... DANSK...18 ENGLISH... 3 NORSK... 19 FRANCAIS...12 SVENSKA...20 ITALINO... 13 NEDERLANDS... 14 ESPANOL...
More informationW & A PARTS MANUAL LEVEE PLOW STANDARD. Model No Blade Model No Blade (Parts Only)
W & A PARTS MANUAL LEVEE PLOW STANDARD Model No. 824 -- 8 Blade Model No. 836 -- 10 Blade (Parts Only) SPECIALIZED FARM EQUIPMENT Quality Products from W & A MANUFACTURING COMPANY P.O. Box 5238, Pine Bluff,
More informationC2211/FMTPJ07CHLDCC5.5
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C2211/FMTPJ07CHLDCC5.5 FRONT TIEDOWNS CHAIN AND CLEVIS REMOVED 07.06.2011 Minor movement (or settling) can occur in some incidental harsh driving conditions
More informationInstallation Instructions for Wall Mount, Deck Mount and Pre-rinse Faucets
Installation Instructions for Wall Mount, Deck Mount and Pre-rinse Faucets SAVE FOR END USER ELKAY 2222 CAMDEN COURT OAK BROOK, IL 60523 USA WALL MOUNT ASSEMBLY General Instructions Turn off the water
More informationSolera Classic Awning OEM INSTALLATION MANUAL
Solera Classic Awning OEM INSTALLATION MANUAL TABLE OF CONTENTS System and Safety Information 2 Preparation 3 Resources Required 3 Installation 3 Installing the Awning Rail (If Necessary) 3 Assembling
More informationROCKING HAMMOCK GD-600. Model GD-600. Retain This Manual for Reference OWNER'S MANUAL
NOTE: Please read all instructions carefully before using this product ROCKING HAMMOCK Table of Contents Safety Notice GD-600 Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model
More informationOtter Pro XT Cabin Installation and Set-Up Instructions
Otter Pro XT Cabin Installation and Set-Up Instructions Otter Pro XT Cabin Fits Medium Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro XT Thermal Cabin
More information300 Model 870 Four Wheel Hose Cart Owner s Manual
300 Model 870 Four Wheel Hose Cart Owner s Manual IMPORTANT: READ THE OWNER S MANUAL BEFORE ASSEMBLING TOOLS REQUIRED: TWO ADJUSTABLE WRENCHES; HAND PUMP Estimated assembly time: 30 minutes PARTS LIST
More informationOtter Pro X-Over Lodge Installation and Set-Up Instructions
Otter Pro X-Over Lodge Installation and Set-Up Instructions Otter Pro X-Over Lodge Fits Magnum Otter II & Pro Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro X-Over Lodge
More informationINSTALLATION INSTRUCTIONS AND OWNER'S MANUAL AWNINGS. For trailers & motor homes with straight sides TOOLS REQUIRED
AWNINGS INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL For trailers & motor homes with straight sides TOOLS REQUIRED 1/4" electric drill Ratchet handle kit 3/8" & 7/16" socket No. 1 and No. 2 screwdriver
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS D4101. REVISED vers6 BY: JL 8/6/2015 TECH SUPPORT (800)
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS D4101 REVISED vers6 BY: JL 8/6/2015 TECH SUPPORT (800) 246-8132 AFTER INSTALL, PLEASE GIVE THIS BOOKLET TO YOUR CUSTOMER 1 Warnings Truck Bed and Camper
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C4201. REVISED Version7 BY: JL 8/6/2015 TECH SUPPORT (800)
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C4201 REVISED Version7 BY: JL 8/6/2015 TECH SUPPORT (800) 246-8132 AFTER INSTALL, PLEASE GIVE THIS BOOKLET TO YOUR CUSTOMER 1 Warnings Truck Bed and Camper
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C2204A
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C2204A Warnings Truck Bed and Camper Protection Torklift does not recommend installing your camper on top of a plastic bed liner (or other compressible
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS. Part # C3206. REVISED Version 6 BY: JL 8/5/2015 TECH SUPPORT (800)
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS Part # C3206 REVISED Version 6 BY: JL 8/5/2015 TECH SUPPORT (800) 246-8132 Warnings Truck Bed and Camper Protection Torklift does not recommend installing
More informationInstallation Instructions Part # 2784 Awning
Please read instructions entirely before installing this product. Parts Included Qty Parts Included Qty 1 Flat Washer (U-Bolt) 4 L Bracket 2 Nylock Nut ( U-Bolt) 4 Stake with Cord 2 6mm x 1 Bolt/Nut 10
More informationPARTS INCLUDED IN YOUR KIT. You may want to lay them out in this manner for accessibility. Foam has NO adhesive to touch truck finish.
-'07 Ford Sport Trac Tarp Assembly with Cab Rail, Tail Rail and Support Bows attached. Left and Right Side Rail Assemblies Sport Trac Brackets (x4) Clamp Bolts Allen Wrench PARTS INCLUDED IN YOUR KIT.
More informationNordic Plow. Lawn Tractor Plow w / Handle (PLOW) 771 W. North Avenue, West Chicago, IL Copyright 1/1/16
Lawn Tractor Plow w / Handle by Nordic Plow LAWN TRACTOR ATTACHMENT ASSEMBLY TIPS... DANSK...15 ENGLISH... 3 NORSK... 16 FRANCAIS... 9 ITALINO... 10 NEDERLANDS... 11 ESPANOL... 1 SVENSKA...17 POLSKI...
More informationSafety instructions and warnings Package contents and parts Tool requirements Product features... 5
Door Awning : PA Series Owner s Manual For safety reasons, please carefully read and understand all written instructions and warnings in this manual prior to assembling or installing this product. Table
More informationPARTS BOOK CATALOG SIDE HD FLAIL HEADS TRACTOR MID-MOUNT
PARTS BOOK CATALOG SIDE HD FLAIL HEADS TRACTOR MID-MOUNT DIAMOND MOWERS, Inc. 350 E 60 th St. North Sioux Falls, SD 57104 FOR WARRANTY CALL DIAMOND MOWERS DIRECT: 888-960-0364 OUR TECHNICIANS WILL DIAGNOSE
More informationVISIT OUR WEBSITE: OR CALL US TOLL FREE AT
Model #710 WATH THE VIEO Owner s Manual VISIT OUR WEBSITE: WWW.LIBERTYGARENPROUTS.OM OR ALL US TOLL FREE AT 1-866-820-5805 LIBERTY GAREN PROUTS, IN. 1161 SOUTH PARK RIVE, KERNERSVILLE N 27284 IMPORTANT:
More informationOwner's Manual. Safety Instructions. This Product is Produced Exclusively by
Product May Vary Slightly From Pictured. Owner's Manual Safety Instructions! WARNING This equipment is for home use only. Do not use in institutional or commercial applications. Failure to follow this
More informationOPERATION MANUAL 14 Rigging Sheave Manufactured by Wireline Technologies, Inc. Serial Number
OPERATION MANUAL 14 Rigging Sheave Manufactured by Wireline Technologies, Inc. Serial Number Introduction This manual explains the use and care of 14 rigging sheaves manufactured by Wireline Technologies,
More informationPARTS INCLUDED IN YOUR KIT. You may want to lay them out in this manner for accessibility. Foam has NO adhesive to touch truck finish.
INSTALL ATION SHEET Tarp Assembly with Cab Rail, Tail Rail and Support Bows attached. Left and Right Side Rail Assemblies U Clamps (x 6) NOTICE: If your truck has a bedliner that wraps over any top edges,
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C3215/C3215A
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C3215/C3215A Minor movement (or settling) can occur in some incidental harsh driving conditions (On or off road). A rubber bed mat is not a requirement
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS D2126, D2127. REVISED version 8 BY: TD 1/30/2015 TECH SUPPORT (800)
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS D2126, D2127 REVISED version 8 BY: TD 1/30/2015 TECH SUPPORT (800) 246-8132 Warnings Truck Bed and Camper Protection Torklift does not recommend installing
More informationUrea/Adblue Hose Reel
www.scintex.com.au sales@scintex.com.au Model: SHR3408 Urea/Adblue Hose Reel Product Manual Specifications Spring driven drum: for automatic rewind. Locking ratchet: to maintain the desired length of hose
More informationGas Go Anywhere /23/01
Gas Go Anywhere 55014 02/23/01 FOR OUTDOOR USE ONLY This grill does not include an LP fuel tank. Check Package Contents You should have received the parts listed below. While we give much attention to
More informationINSTALLATION INSTRUCTIONS for automatic awnings
Custom made Awnings and Blinds Item No 0756 INSTALLATION INSTRUCTIONS for automatic awnings AUTOMATIC AWNING IMPORTANT INFORMATION BEFORE INSTALLING YOUR AUTOMATIC AWNING Updated 08/09/15 AN AWNING INSTALLATION
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS FRONT TIEDOWNS CHAIN AND CLEVIS REMOVED
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C2205/FMTPJ01NDCHSB FRONT TIEDOWNS CHAIN AND CLEVIS REMOVED 07.06.2011 Minor movement (or settling) can occur in some incidental harsh driving conditions
More informationBowDown. MiniMuM Crossbar spread 24 (61CM) Steel Hook (2X) Buckle Strap (2X) Plastic Tube (2X) Plain Strap (2X) SHORT BLACK T-BOLT (2x) BOWDOWN (2x)
BowDown MiniMuM Crossbar spread 24 (61CM) Heavy Duty strap (2x) SHORT BLACK T-BOLT (2x) BOWDOWN (2x) Bow Stern Tie Down Buckle Strap (2X) Plastic Tube (2X) Plain Strap (2X) Steel Hook (2X) IMPORTANT WARNING
More informationASSEMBLY INSTRUCTIONS SHOWER CADDY
ASSEMBLY INSTRUCTIONS SHOWER CADDY 08 H X 0.5 W X 8.5 D IN (274.32 H X 26.67 W X 2.59 D CM ) 2 USA 877 282 695 B A T H R O O M MODEL: 4387 YEAR WARRANTY Parts List D B A E G H C F I C PART DESCRIPTION
More informationAND LOAD CANOPY RACK SPECIFICATIONS
8MAY15 INSTRUCTIONS for the LOCK AND LOAD CANOPY RACK SPECIFICATIONS and SAFE LOADING REQUIREMENTS The Lock and Load ladder carrier for Truck Caps is a rack designed to mount to the top of a pickup truck
More informationLM601 Landmark Permanent Blind
LM601 Landmark Permanent Blind Get parts online at www.huntriversedge.com P/N: 26742 REV1: 01/13/17 2017 RETI All Rights Reserved INTRODUCTION Landmark Permanent Blinds are engineered with you the hunter
More informationInstallation Instructions
Installation Instructions For: Jeep Wrangler TJ Strapless Bikini Part Number 52521 To be used with or without Soundbar To be used with or without Door Side Rails Congratulations on your purchasing decision.
More informationInstallation and User s Manual 12 x 10 MOTORIZED AWNING
12 x 10 MOTORIZED AWNING Installation and User s Manual 12 x 10 MOTORIZED AWNING 088-1763-0 Stop Please read and understand this manual before any assembly or use of this product. Before beginning assembly
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS F4006. REVISED vers5 BY: DSK 8/21/15 TECH SUPPORT (800)
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS F4006 REVISED vers5 BY: DSK 8/21/15 TECH SUPPORT (800) 246-8132 AFTER INSTALL, PLEASE GIVE THIS BOOKLET TO YOUR CUSTOMER 1 Warnings Truck Bed and Camper
More informationAssembly. Step 3. Attach the safety bracket (7) to the Pivot ARM (6).
Assembly Step 1. A. Stand the base of the machine by separating the U-frames (1,2). Pull the Front and Rear U-Frames (1,2) as far apart from each other as possible. Then push down on the middle of the
More informationKontrol Kube Advanced Owners Manual
Mobile Containment. Simplified. TM Kontrol Kube Advanced Owners Manual KONTROL KUBE www.kontrolkube.com 800.343755 1 IMPORTANT SAFETY INFORMATION SAVE THESE INSTRUCTIONS. CAREFULLY READ AND FOLLOW THESE
More informationAssembly and Installation Instructions
U.S. patent number 8,708,369 part number 4750 for Blue Ox tow bars with Blue Ox brackets, Demco tow bars with Demco brackets, and all motorhome-mounted ROADMASTER tow bars Assembly and Installation Instructions
More informationMOTORIZED FOLDING CAMPER WINCH
OWNER'S MANUAL MOTORIZED FOLDING CAMPER WINCH The 12 Volt Motorized Folding Camper Winch is used to raise and lower the top of folding campers with the touch of the switch, eliminating tiresome hand cranking.
More informationWIDESPREAD LAVATORY MODELS WITH HI-ARC SPOUT
5951, 5961, 5981, 5983, 5993 SERIES MT122B INSTALLATION INSTRUCTIONS THESE INSTRUCTIONS MUST BE LEFT WITH HOMEOWNER WIDESPREAD LAVATORY MODELS WITH HI-ARC TRADITIONAL CROSS NOTE: Handle Inserts are not
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS FRONT TIE DOWNS F2017. REVISED vers7 BY: JL 8/7/15 TECH SUPPORT (800)
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS FRONT TIE DOWNS F2017 REVISED vers7 BY: JL 8/7/15 TECH SUPPORT (800) 246-8132 AFTER INSTALL, PLEASE GIVE THIS BOOKLET TO YOUR CUSTOMER 1 Warnings Truck
More informationCRD120SC TUBING CUTTER
CRD120SC TUBING CUTTER OPERATIONS MANUAL 1 VERSION 2.1 LAST EDITED 05.01.2018 cleanroomdevices.com Table of Contents Table of Contents....2 1.0 General Product & Safety Information... 3 1.1 Product Information
More informationRCCK. Pivot Plug 2x. Sharp Screw 2x TAKE TIME - READ AND UNDERSTAND INSTRUCTIONS COMPLETELY!
RCCK Revolution Cargo Conversion Kit Congratulations on your purchase of the BOB Revolution Cargo Conversion Kit (RCCK). It s designed to easily convert your existing BOB Revolution stroller frame into
More informationD3107/ FMT09DGRO6.5 REAR TIEDOWNS W/ FACTORY INSTALLED RECEIVER APPLICATION FITS
D3107/ FMT09DGRO6.5 REAR TIEDOWNS W/ FACTORY INSTALLED RECEIVER APPLICATION FITS Minor movement (or settling) can occur in some incidental harsh driving conditions (on or off road). A rubber bed mat is
More informationLegacy Basic Acoustical Shell
Owner s Manual Legacy Basic Acoustical Shell CONTENTS Safety Precautions.................................. 2 General....................................... 2 Set Up and Usage..............................
More informationRETRACTABLE AWNING w/ OPTIONAL HOOD ASSEMBLY INSTRUCTIONS
Contact us @ (800)851-0865 RETRACTABLE AWNING w/ OPTIONAL HOOD ASSEMBLY INSTRUCTIONS Congratulations on your purchase of a new retractable awning. With proper installation this awning will provide years
More information80070 TOP MOUNT CAMPER SHELL and TRANSIT CONNECT RACK TMCS_3:1
ASSEMBLY INSTRUCTIONS for : 80070 TOP MOUNT CAMPER SHELL and TRANSIT CONNECT RACK TMCS_3:1 (916) 638-8703 (800) 343-7486 11261 Trade Center Drive Rancho Cordova, CA 95742 www.kargomaster.com Transit ASSEMBLY
More informationThermal King Blankets and Storage Reels 7100 Spectrum Lane Missoula MT EverActive Brands
Thermal King Blankets and Storage Reels 7100 Spectrum Lane Missoula MT 59808 800.791.8056 www.spectrumproducts.com 2012 EverActive Brands Rev 3/18/16 Contents Blanket Specifications. 1 Pool Blanket Cleaning
More informationDIAMOND TECH INTERNATIONAL Innovations For Creativity DIAMOND LASER BAND SAW OPERATIONS MANUAL
SPEEDSTER-XL INSTRUCTION MANUAL DIAMOND TECH INTERNATIONAL Innovations For Creativity SPEEDSTER-XL DIAMOND LASER BAND SAW OPERATIONS MANUAL SPEEDSTER-XL INSTRUCTION MANUAL - PAGE 1 Before You Begin Read
More informationREAD AND SAVE THESE INSTRUCTIONS! EasyAwn Dome Awning Installation
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC 3575 Trotters Drive, Bldg A Alpharetta, GA 30004 Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE
More informationAssembly and Installation Instructions
U.S. patent number 8,708,369 part number 4750 for Blue Ox tow bars with Blue Ox brackets, Demco tow bars with Demco brackets, and all motorhome-mounted ROADMASTER tow bars Assembly and Installation Instructions
More informationVPH-20 Owner s manual. Video Tripod Head
VPH-20 Owner s manual Video Tripod Head thank you for choosing magnus. Congratulations on your purchase of the VPH-20 Video Pan Head by Magnus. All Magnus Video Heads are designed to balance features professionals
More informationREAD AND SAVE THESE INSTRUCTIONS! EasyAwn Dome Awning Installation
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Dome Awning Installation
More informationOWNER S MANUAL. Gravity Model 5201
OWNER S MANUAL Gravity 1000 Model 5201 The specifications of this product may vary from this photo and are subject to change without notice. IRONMAN, IRONMAN TRIATHLON and M-DOT are registeved trademarks
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C4203. REVISED vers5 BY: JL 8/6/15 TECH SUPPORT (800)
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C4203 REVISED vers5 BY: JL 8/6/15 TECH SUPPORT (800) 246-8132 AFTER INSTALL, PLEASE GIVE THIS BOOKLET TO YOUR CUSTOMER 1 Warnings Truck Bed and Camper
More informationPR-429BF-600M. Bell 429 Blade Fold Kit Operations Manual
Table of Contents Table of Contents... 1 Record of Revisions... 2 References... 3 Introduction... 4 Contact Information... 4 Prerequisites... 5 First Time Use... 6 Blade Clamp Placement... 6 Blade Clamp
More informationBostonian style (DOME) Awning ASSEMBLY AND INSTALLATION INSTRUCTIONS
Bostonian style (DOME) Awning ASSEMBLY AND INSTALLATION INSTRUCTIONS CAUTION: When you are opening the box keep children away. This awning frame contains sharp metal and small hardware parts. Choking hazard:
More informationOperating Instructions
Operating Instructions Medium and High Pressure Model Numbers: RT602- RT635- RT602- RT635- RT603- RT650- RT603- RT650- RT605- RT825- RT605- RT650-SM RT802- RT835- RT425- RT803- RT402- RT435- RT625- RT403-
More informationINSTALLATION GUIDELINES
IMPORTANT: To ensure this product is installed properly, you must read and follow these guidelines. The owner/user of this product must keep this information for future reference. This product must be
More informationDO NOT USE WITH CROSSBAR SPREAD LESS THAN 24.
TM Please read all instructions carefully before assembly, installation and/or use of this product. DO NOT USE WITH CROSSBAR SPREAD LESS THAN 24. WARNING: Do not exceed the weight limit of your vehicle
More informationMOTORIZED FOLDING CAMPER WINCH
OWNER'S MANUAL MOTORIZED FOLDING CAMPER WINCH With 1200lb Lift Capacity The 12 Volt Motorized Folding Camper Winch is used to raise and lower folding campers with the touch of the switch, eliminating hand
More informationStainless Clip FP3011-1S Qty 4
Plastic Storage 16'-FP3013 20'-FP3012 Groundsleeve 16'-FP033-1 20'-FP025-1 Stainless Clip FP3011-1S Qty 4 Universal Wheelstand FP9040 Locking Collar 16'-FP034-1 20'-FP026-1 Stop Nut & Bolt FP3000-1 5/64"
More information