15 AND 25 GALLON SPRAYERS INSTRUCTION MANUAL

Transcription

1 1 481 Panet Road Winnipeg, MB R2C 2Z1 15 AND 25 GALLON SPRAYERS INSTRUCTION MANUAL GENERAL INFORMATION The purpose of this manual is to assist you in operating and maintaining your lawn and garden sprayer. Please read it carefully as it furnishes information which will help you achieve years of dependable trouble free operation. WARRANTY-PARTS-SERVICE To obtain prompt, efficient service, always remember to give the item number and your model number. Whenever you need parts or repair service, contact Princess Auto Ltd. at: Telephone # Fax # The sprayer is shipped in a carton and requires assembly before it can be used. Refer to parts list and drawing, and then follow this procedure when assembling: IA) ASSEMBLY INSTRUCTION FOR 25 GAL. PULL TYPE, ITEM # (P ) 1) Install tow frame (19) on frame (17) using bolts (18) and lock nuts (13). 2) Install boom frame (10) on frame (17) using bolts (9) and lock nuts (13). 3) Install lid and outlet plug on tank (69) with tether straps. 4) Install tank (69) on frame (17) using bolts, lock washers, and plain washers (14), (15), (16). 5) Slide wheels (12) on to axle followed by washer (11) and install cotter pin (71). 6) Insert boom slide frame (55) into bottom boom frame (10) and lock in position using pin (67) and thumb screw (66). 7) Install boom arm left inside (1), right inside (50) on frame boom slide (55) using carriage bolt, plain washer, lock washer, and wing nut (54), (4), (56), (57). 8) Install boom arm left outside (5), right outside (43) on inside boom arms (1),(50) using bolt, plain washer, lock washer, and nut (2), (4), (56), (3). 9) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings 10) Mount pump (27) and switch holder (28) to tank using screws (34). NOTE: There is an extra 6 feet of red wire so that the switch can be mounted near the operator. If mounted on the tank, wrap the extra 6 feet of wire REV. 05 NOV. 03 2

2 11) Install grommet (47) on tank (69). 12) Insert hose (48) through grommet (47). Lubricate grommet for ease of installation. 13) Slide hose clamp (46) on hose (48). Insert hose to elbow (26) on pump and tighten clamp. From inside tank install barb (45) and strainer (44) to hose (48). Note: Place hose in bottom of tank, so that it does not curl upward. 14) Slide hose clamp (38) on hose (64), insert hose on barb hose flat (35), slide hose clamp on opposite end of hose, and connect the hose into tee (52) and tighten clamps. Important: Ensure direction of the tee is as per drawing. 15) Install barb (25) and vinyl washer (62) to tank (69). 16) Slide hose clamp (38) on hose (33), connect hose to barb (25), slide hose clamp on opposite end of hose. Connect hose on barb hose flat (35) and tighten clamps. 17) Install clips (32) to tank (69) using screws (60). 18) Slide hose clamp (38) on hose (58), connect hose to barb hose flat (35). Connect opposite end to wand (59). Hose can be wrapped around tank and wand inserted in clips. 19) Install nut (6) on elbow (37) and tee (51), turn the nut up to the end of the thread on elbow and tee. 20) Pass elbow (37) and tee (51) through hole on boom arms (43), (50), (1), (5). 21) Install O-ring (40) on filter (39). Insert filter (39) in elbow (37) and tee (51) and install O-ring (40), nozzle tip (41) and nut (42) on elbow and tee. 22) Tighten nut (6) toward boom. Do not over tighten. Adjust the nozzle spray direction directly towards the ground. 23) Repeat 19, 20, 21 and 22 for all nozzles. 24) Tie hoses (49), (8) using cable tie (68) on boom arm holes (1), (5), (43), (50). 25) Make sure all fittings are tight. Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying. NOTE: YOUR SPRAYER IS READY TO USE. Read instruction manual and understand fully before operating the unit. 3 IB) ASSEMBLY INSTRUCTION FOR 25 GAL. PULL TYPE DELUXE,

3 ITEM # (P.20-22) 1) Install tow frame (33) on frame (36) using bolt (35) and lock nut (37). 2) Install boom frame (27) on frame (36) using bolt (67) and lock nut (37). 3) Install tank (38) on frame (36) using bolt, lock washer, and plain washer (30), (31), (32). 4) Install lid and outlet plug on tank (38) with tether straps. 5) Slide tires (29) on to axle and install washer (28) and cotter pin (66). 6) Insert boom slide frame (14) on boom frame (27) and lock in position using pin (25) and thumb screw (17). 7) Install middle boom (18) and spacers (15) on frame boom slide (14) with bolt (13) and lock nut (37). 8) Install left boom (21) and right boom (4) on middle boom (18) with bolt (67) and lock nut (37). 9) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings. 10) Mount pump (44) and switch holder (41) to tank using screws (45). NOTE: There is an extra 6 feet of red wire so that the switch can be mounted near the operator. If mounted on the tank, wrap the extra 6 feet of wire. 11) Install grommet (11) on tank (38). 12) Install barb (39) and vinyl washer (6) to tank (38). 13) Insert hose (57) through grommet (11). Lubricate grommet for ease of installation. Note: Place hose in bottom of tank, so that it does not curl upward. 14) Slide hose clamp (9) on hose (57). Insert hose to elbow (42) on pump and tighten clamp. From inside tank install barb (58) and strainer (59) to hose (57). 15) Install clips (63) to tank (38) using screws (64). 16) Slide hose clamp (49) on hose (26), insert hose on barb hose flat (48), and connect the other end of hose into barb on wand (20) and tighten clamp. Hose can be wrapped around tank and wand inserted in clips. 17) Slide hose clamp (49) on hose (50), insert hose on barb hose flat (48), slide hose clamp on opposite end of hose, and connect hose to barb (39) and tighten clamps 18) Slide hose clamp (49) on hose (10), insert hose on barb hose flat (48), slide hose clamp on opposite end of hose, and connect hose to cross (16) and tighten clamps. 19) Slide hose clamp (49) on hose (2), connect hose to elbow (1), slide hose clamp on opposite end of hose. Connect hose to tee (19) and tighten clamps. 4

4 20) Slide hose clamp (49) on hose (8), connect hose to tee (19). Slide hose clamp on opposite end of hose, connect hose to cross (16) and tighten clamps. 21) Repeat 19 and 20 for the opposite side. 22) Install nozzle bodies (1), (16), (19) to boom with clamps (22). The nozzle bodies should be at 30 spacing. The inside hoses (8) are longer so that the outside booms can pivot. 23) Insert nozzle (51) into cap (23) followed by rubber gasket (52). Insert filter (53) in nozzle bodies (1), (16), (19). Install cap (23) on nozzle bodies (1), (16), (19) by turning half a turn. 24) Rotate outside booms (4) and (21) so they are folded in. Install springs (7) on booms.tighten or loosen locknut (37) until the outside arms can rotate on their own with the spring installed. NOTE: If locknut is too loose, movement of boom arm can be dangerous. 25) Make sure all fittings are tight. Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying. YOUR SPRAYER IS READY TO USE. NOTE: Read instruction manual and understand fully before operating the unit. IC) ASSEMBLY INSTRUCTION FOR 25 GAL. THREE POINT HITCH, ITEM # (P ) 1) Install boom frame (48) on frame (40) using bolt (49) and lock nut (44). 2) Install lid and outlet plug on tank (39) with tether straps. 3) Install tank (39) on frame (40) using bolt, lock washer, and plain washer (45), (46), (47). 4) Insert boom slide frame (11) on boom frame (48) and lock in position using pin (50) and thumb screw (7). 5) Install boom arm left inside (19), right inside (4) on frame boom slide (11) using carriage bolt, plain washer, lock washer, and wing nut (14), (10), (9), (8). 6) Install boom arm left outside (28), right outside (1) on inside boom arms (19), (4) using bolt, plain washer, lock washer, and nut (27),(10),(9),(2). 7) Install barb (33) and vinyl washer (21) to tank (39). 8) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings. 9) Mount pump (34) and switch holder (32) to tank using screws (26). NOTE: There is an extra 6 feet of red wire so that the switch can be mounted near the operator. If mounted on the tank, wrap the extra 6 feet of wire. 5 10) Install grommet (54) on tank (39). 11) Insert hose (53) through grommet (54). Lubricate grommet for ease of installation.

5 Note: Place hose in bottom of tank, so that it does not curl upward. 12) Slide hose clamp (63) on hose (53), insert hose to elbow (31) on pump and tighten clamp. 13) Slide hose clamp (5) on hose (13), insert hose on barb hose flat (17), slide hose clamp on opposite end of hose, and connect hose into tee (12) and tighten clamps. 14) Slide hose clamp (5) on hose (18), connect hose to tee (12), slide hose clamp on opposite end of hose. Connect hose into tee (6) and tighten clamps. 15) Slide hose clamp (5) on hose (55), connect hose to tee (6). Slide hose clamp (5) on opposite end of hose, insert elbow (56) into hose and tighten clamp. 16) Repeat 15 and 16 for the opposite side. 17) Install nut (57) on elbow (56) and tee (6), turn the nut up to the end of the thread on elbow and tee. 18) Pass elbow (56) and tee (6) through hole on boom arms (1),(6),(19),(28). 19) Install O-ring (58) on filter (59). Insert filter (59) in elbow (56) and tee (6) and install O-ring (58), nozzle tip (60) and nut (61) on elbow and tee. Hand tighten nut (61). 20) Tighten nut (57) toward boom. Do not over tighten. Adjust the nozzle spray direction directly towards the ground. 21) Repeats for the other nozzles. 22) Tie hoses (55),(18) using cable tie (68) on boom arm holes (1),(4),(19),(28). 23) Install clips (38) to tank (39) using screws (37). 24) Slide hose clamp (5) on hose (3), insert hose on barb hose flat (17), and connect the other end of hose into barb on wand (30) and tighten clamp. Hose can be wrapped around tank and wand inserted in clips. 25) Slide hose clamp (5) on hose (25), insert hose on barb hose flat (17), slide hose clamp on opposite end of hose, and connect hose to barb (33) and tighten clamps. 26) Make sure all fittings are tight. Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying. NOTE: YOUR SPRAYER IS READY TO USE. Read instruction manual and understand fully before operating the unit. ID) ASSEMBLY INSTRUCTION FOR 25 GAL. PULL TYPE BOOMINATOR, ITEM # (P. 26 & 27) 1) Install tow frame (37) on frame (35) using bolt (38) and lock nut (3). 6 2) Install boom frame (1) on frame (35) using bolt (2) and lock nut (3).

6 3) Install tank (34) on frame (35) using bolt, lock washer, and plain washer (41), (40), (39). 4) Install lid and outlet plug on tank (34) with tether straps. 5) Slide tires (43) on to axle followed by washer (42) and install cotter pin (44). 6) Insert nozzle holder (5) on boom frame (1) and lock in position using thumb screw (4). 7) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings. 8) Mount pump (18) and switch holder (24) to tank using screws (46). NOTE: There is an extra 6 feet of red wire so that the switch can be mounted near the operator. If mounted on the tank, wrap the extra 6 feet of wire. 9) Install grommet (26) on tank (34). 10) Install barb (28) and vinyl washer (12) to tank (34). 11) See bottom left hand view for hose assembly. Insert hose (21) through grommet (26). Lubricate grommet for ease of installation. Note: Place hose in bottom of tank, so that it does not curl upward. 12) Slide hose clamp (22) on hose (21). Insert hose to elbow (29) on pump and tighten clamp. From inside tank install barb (47) and strainer (27) to hose (21). 13) Install clips (33) to tank (34) using screws (32). 14) Slide hose clamp (9) on hose (49), insert hose on barb hose flat (11), and connect the other end of hose into barb on wand (16) and tighten clamp. Hose can be wrapped around tank and wand inserted in clips. 15) Slide hose clamp (9) on hose (25), insert hose on barb hose flat (11), slide hose clamp on opposite end of hose, and connect hose to barb (28) and tighten clamps 16) Slide hose clamp (9) on hose (50), insert hose on barb hose flat (11), slide hose clamp on opposite end of hose, and connect hose to brass barb (15) and tighten clamps. 17) Insert brass barb (15) into hole on nozzle holder (5) and install check valve (5) (Make sure arrows on check valve are pointing in the direction of flow.) to brass barb followed by nozzle (7). Make sure teflon tape is used on threads. Tighten nozzle enough to prevent leaking and make sure nozzle is pointing downwards. When sprayer is first tested with water, rotate nozzle for even spray distribution. Do not overtighten. 18) Make sure all fittings are tight. Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying. 7 YOUR SPRAYER IS READY TO USE. NOTE: Read instruction manual and understand fully before operating the unit.

7 IE) ASSEMBLY INSTRUCTION FOR 15 GAL. SPOT, ITEM # (P. 28 & 29) 1) Install lid and outlet plug on tank (12) with tether straps. 2) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings. 3) Mount pump (17) to tank using screws (18). 4) Install grommet (29) on tank (12). 5) Install barb (13) and vinyl washer (5) to tank (12). 6) Insert hose (20) through grommet (29). Lubricate grommet for ease of installation. Note: Place hose in bottom of tank, so that it does not curl upward. 7) Slide hose clamp (15) on hose (20) insert the hose to elbow (14) on pump and tighten clamp. From inside tank install barb (19) and strainer (21) to hose (20). 8) Slide hose clamp (23) on hose (16) insert the hose on barb hose flat (4). Slide hose clamp on opposite end of hose and connect to barb (13). 9) Plug wire (30) to wire from pump. 10) Install clips (24) to tank (12) using screws (25). 11) Slide hose clamp (23) on hose (2), insert the hose on barb hose flat (4). Slide hose clamp on opposite end of hose, and connect the hose into wand (1) and tighten clamp. Hose can be wrapped around tank and wand inserted in clips. 12) Make sure all fittings are tight. Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying. NOTE: YOUR SPRAYER IS READY TO USE. Read instruction manual and understand fully before operating the unit. 8 IF) ASSEMBLY INSTRUCTION FOR 15 GAL. ATV BOOMINATOR, ITEM # (P. 30 & 31) 1) Install lid and outlet plug on tank (8) with tether straps. 2) Install frames (4) to tank (8) using bolt, lock washer and plain washer (1),(2),(3). 3) Install right bracket (6) and left bracket (38) to frame (4) using bolt, plain washer, and lock nut (5),(3),(36). The holes that you use on the brackets are dependant on your ATV.

8 4) Install boom support (39) to brackets (6) and (38) using bolt, 2 washers, and lock nut (5),(3),(3),(36). 5) Insert nozzle holder (43) into boom support (39) and lock in position using thumb screw (41). Install bolt (46) to nozzle holder with lock nut (42). 6) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings. 7) Mount pump (29) to tank using screws (28). 8) Install grommet (33) on tank (8). 9) Insert hose (34) through grommet (33). Lubricate grommet for ease of installation. Note: Place hose in bottom of tank, so that it does not curl upward. 10) Slide hose clamp (16) on hose (34). Insert hose to elbow (30) on pump and tighten clamp. From inside tank install barb (10) and strainer (7) to hose (34). 11) Install barb (15) and vinyl washer (24) to tank (8). 12) Slide hose clamp (26) on hose (13), insert hose on barb hose flat (23) and tighten clamps. 13) Install clips (11) to tank (8) using screws (12). 14) Slide hose clamp (26) on hose (40), insert hose on barb hose flat (23). Slide hose clamp on opposite end of hose and connect the hose into barb on wand (14). Hose can be wrapped around tank and wand inserted in clips. 15) Slide hose clamp (26) on hose (27), insert hose on barb hose flat (23), slide hose clamp on opposite end of hose, and connect hose to barb (15) and tighten clamps. 16) Insert brass barb (47) into hole on nozzle holder (43) and install check valve (44) (Make sure arrows on check valve are pointing in the direction of flow.) to brass barb followed by nozzle (45). Make sure teflon tape is used on threads. Tighten nozzle enough to prevent leaking and make sure nozzle is pointing downwards. When sprayer is first tested with water, rotate nozzle for even spray distribution. Do not overtighten. 17) Make sure all fittings are tight. Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying. 9 NOTE: YOUR SPRAYER IS READY TO USE. Read instruction manual and understand fully before operating the unit. IG) ASSEMBLY INSTRUCTION FOR 15 GAL. PULL TYPE, ITEM # (P ) 1) Install tow frame (20) on frame (21) using bolt (19) and lock nut (46). 2) Install lid and outlet plug on tank (18) with tether straps. 3) Install tank (18) on frame (21) using bolt, lock washer, and washer plain (22), (23), (24).

9 4) Install boom frame (37) on frame (21) using bolt, lock washer, and weld nut (22), (23), (26). 5) Slide wheels (27) on to axle followed by washer (28) and install cotter pin (59). 6) Install boom pipe (36) to the required hole location using U bolt (38) and lock nut (57). 7) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings. 8) Mount pump (11) and switch holder (13) to tank using screws (8). NOTE: There is an extra 6 feet of red wire so that the switch can be mounted ear the operator. If mounted on the tank, wrap the extra 6 feet of wire. 9) Install grommet (16) on tank (18). 10) Insert hose (15) through grommet (16). Lubricate grommet for ease of installation. Note: Place hose in bottom of tank, so that it does not curl upward. 11) Slide hose clamp (42) on hose (15) insert hose to elbow (43) on pump and tighten clamp. From inside tank install barb (44) and strainer (45) to hose (15). 12) Slide hose clamp (2) on hose (29), insert hose on barb hose flat (4), slide hose clamp on opposite end of hose, and connect the hose into tee (39) and tighten clamps. Important: Ensure direction of the Tee is as per drawing. 13) Install clips (51) to tank (18) using screws (52). 14) Slide hose clamp (2) on hose (55), insert hose on barb hose flat (4), slide hose clamp on opposite end of hose, and connect the hose into barb on wand (56) and tighten clamps. Hose can be wrapped around tank and wand inserted in clips. 15) Install barb (17) and vinyl washer (25) to tank (18). 16) Slide hose clamp (2) on hose (1), insert hose on barb hose flat (4) and tighten clamps. 17) Slide hose clamp (2) on hose (1), connect hose to tee (39),and tighten clamp. 18) Slide hose clamp (2) on hose (1), insert elbow (30) into hose and tighten clamp. 19) Repeat 17 and 18 for the opposite side ) Install steel clamp (35) on the end of boom pipe (36). 21) Install nut (31) on elbow (30), turn the nut up to the end of the thread on elbow nozzle. 22) Pass elbow (30) through hole of steel clamp (35). 23) Install o'ring (33) on filter (32). Insert filter (32) in elbow (30) and install o'ring (33), nozzle tip (5) and nut (34) on elbow. Hand tighten nut (34). 24) Turn nut (31) toward steel clamp (35). Do not over tighten. Adjust the nozzle spray direction directly towards the ground.

10 25) Repeat 20, 21, 22, 23 and 24 for the opposite side. 26) Make sure all fittings are tight. Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying. NOTE: YOUR SPRAYER IS READY TO USE. Read instruction manual and understand fully before operating the unit. II) ASSEMBLY INSTRUCTION FOR 15 GAL. SPOT, ITEM # (P. 35 & 36) 1) Install lid and outlet plug on tank (14) with tether straps. Use Teflon tape on all pipe thread fittings. 2) Mount pump (3) to tank using screws (5) and washers (4). 3) Install grommet (8) on tank (14). 4) Insert hose (7) through grommet (8). Note: Place hose in bottom of tank, so that it does not curl upward. 5) Slide hose clamp (6) on hose (7) insert the hose to hose barb on pump and tighten clamp. From inside tank install barb (9) and strainer (10) to hose (7). 6) Install clips (16) to tank (14) using screws (15). 7) Slide hose clamps (6) on hose (1) insert the hose on barb on the pump and tighten the clamp. Slide hose clamp on opposite end of hose and connect to barb on the wand (2). 8) Plug wire (18) to wire from pump. 9) Make sure all fittings are tight. Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying. NOTE: YOUR SPRAYER IS READY TO USE. Read instruction manual and understand fully before operating the unit. 11 II OPERATION Read operation instruction manual and run the sprayer using water only for test. 1) This sprayer is designed to be used with a garden tractor or ATV. 2) The pumping system draws solution from the tank to the pump. The pump forces the solution under pressure to the boom or wand. 3) Make sure the toggle switch is in the off position.

11 4) Install the red wire to a "hot" connection on the vehicle with a 12 volt DC power source or the positive 12 volt battery post. The black wire should be grounded or connected to the negative battery post. 5) Add clean water into tank so that the unit can be tested. Turn the toggle switch to the on position and open the valve for either the boom or wand. Adjust the desired pressure by slowly opening or closing valve, which has the hose that returns to the tank. 6) The wand or boom may be shut off at anytime when the pump system is running, as the system is protected by an internal relief in the pump. It is best to turn off the pump when it is not in use, to conserve energy from the battery. 7) The height of the boom needs to be adjusted so that there is 50% overlap on the spraying surface (see diagram). NOZZLES HEIGHT SPRAYING SURFACE 50 % OVERLAP If you need to reduce the width to fewer nozzles, remove the nozzle tip and install the plug that is provided. Not applicable to the boominator nozzle. The spray width is adjusted by lowering or raising the boominator nozzle. 8) If it becomes necessary to clean the filters or nozzles, remove the filter from the nozzle body. The filter sceen may now be tapped or flushed with clear water for cleaning. Nozzles can be cleaned by soaking in water and cleaning with a brush and airline. Never blow through by mouth or poke with wire or pins. Not applicable to the boominator nozzle. The boominator nozzle should never need cleaning. 9) WARNING: Some chemicals will damage the valves if allowed to soak untreated for a length of time. Always flush the pump with water after use. Do not allow chemicals to sit in pump for extended times of idleness. Flushing may be done by adding water to the tank and opening the sprayer valve (the hose that flows into the boom and wand) and run your motor for seconds. Follow chemical manufacturers instructions on disposal of all waste water from the sprayer. 12

12 III CALIBRATION 1) Chemical labels may show application rates in gallons per acre, gallons per 1000 square feet, gallons per 100 square feet, or litres per hectare. The TIP CHART on the next page shows gallons per acre and litres per hectare ratings. If your chemical labels use 1000 or 100 square feet use the gallons per acre with the following conversion: - For 1000 square feet: divide by For 100 square feet: divide by ) Once you know how much you are going to spray then determine (from the TIP CHART) the spray pressure (PSI), spraying speed (MPH), and spray width (INCHES) [1 foot = 12 inches]. The weather condition must be considered when setting the sprayer. 3) Determining the proper speed of the tractor can be done by marking off 100, 200, and 300 feet. The speed chart indicates the number of seconds it takes to travel the distances. Set the throttle, and with a running start travel the distances. Adjust the throttle until you travel the distances in the number of seconds indicated by the speed chart. Once you have reached the throttle setting needed, mark the throttle location so you can stop and go again (returning to the same speed). SPEED CHART Speed in M.P.H. Time Required in Seconds to Travel a Distance of: (Miles per Hour) 100 ft. 200 ft. 300 ft ) Add water and proper amount of chemical to tank and drive to the starting place for spraying. Adjust pressure with pressure adjusting valve to the pressure required. This must be determined from the nozzle tip chart and application rate recommended by the chemical manufacturer. 13 WARNING: Read your chemical supplier warning labels. CAUTION: - Do not spray on windy days. - Protective clothing must be worn when spraying hazardous chemicals. - Be sure to read and understand this manual before spraying.

13 TIP CHART FOR RED DEFLECTIP NOZZLE FLOW RATE PER NOZZLE Liquid Capacity 3 MPH 4 MPH 5 MPH 6 MPH 7 MPH 8 MPH 9 MPH Pressure GPM per Gal/ Gal/ Gal/ Gal/ Gal/ Gal/ Gal/ L/Ha L/Ha L/Ha L/Ha L/Ha L/Ha PSI Nozzle Acre Acre Acre Acre Acre Acre Acre L/Ha TIP CHART FOR BLUE FAN TIP NOZZLE FLOW RATE PER NOZZLE Liquid Capacity 5 MPH 6 MPH 7 MPH 8 MPH 10 MPH 12 MPH 14 MPH Pressure GPM per Gal/ Acre L/Ha Gal/ Acre L/Ha Gal/ Acre L/Ha Gal/ Acre L/Ha Gal/ Acre L/Ha Gal/ Acre L/Ha Gal/ PSI Nozzle Acre L/Ha TIP CHART FOR THE GREY DEFLECTIP NOZZLE 14 FLOW RATE PER NOZZLE Liquid Capacity 3 MPH 4 MPH 5 MPH 6 MPH 7 MPH 8 MPH 9 MPH Pressure GPM per Gal/ Gal/ Gal/ Gal/ Gal/ Gal/ Gal/ L/Ha L/Ha L/Ha L/Ha L/Ha L/Ha PSI Nozzle Acre Acre Acre Acre Acre Acre Acre L/Ha

14 TIP CHART FOR THE BOOMINATOR NOZZLE TESTED HEIGHT 36, SPRAY WIDTH 16 FEET Liquid 1 MPH 2 MPH 3 MPH 4 MPH 5 MPH 6 MPH 7 MPH Pressure GPM Gal/ Gal/ Gal/ Gal/ Gal/ Gal/ Gal/ L/Ha L/Ha L/Ha L/Ha L/Ha L/Ha PSI Acre Acre Acre Acre Acre Acre Acre L/Ha V AFTER SPRAYING AND WINTER STORAGE 1) Fill half the tank with water and run the pump until clear water comes out at the nozzle end. 2) Flush the system with a chemical neutralizing agent. NOTE: Follow the chemical manufacturers disposal instructions on washing or rinsing water and chemicals. 3) If you are not using it for a long period of time remove nozzle tips and filter. - wash nozzle tips with water or cleaning solution. - blow out orifice. - clean and dry. NOTE: If orifice remains clogged, clean it with a fine bristle brush. Never blow through by mouth or poke with wire or pins or you will damage the orifice. - water rinse and dry tips before storing. 4) The sprayer should be winterized before storage by pumping a solution of water and anti-freeze through the entire plumbing. Proper care and maintenance will prolong the life of the sprayer. 5) The sprayer should not be stored outside, the pump could get damaged from rain. 15 VI TECHNICAL SPECIFICATIONS

15 Item # Tank Tires Pump Boom Type Nozzle Type US Gal. Polyethylene 15 US Gal. Polyethylene 15 US Gal. Polyethylene 25 US Gal. Polyethylene N/A 4.10/ Pnuematic N/A 4.10/ Pnuematic 1.4 gpm Open Flow, Viton Valves, Santoprene Diaphragm, 60 psi Internal By-pass, Built in on/off Switch, 12 vdc, 1.4 gpm Open Flow, Viton Valves, Santoprene Diaphragm, 45 psi Internal By-pass, 12 vdc 1.4 gpm Open Flow, Viton Valves, Santoprene Diaphragm, 60 psi Internal By-pass, Built in on/off Switch, 12 vdc 1.4 gpm Open Flow, Viton Valves, Santoprene Diaphragm, 45 psi Internal By-pass, 12 vdc Approx. Spray Width N/A N/A N/A 40" Boom N/A 10' Fold-up Ball Check Strainer, #3 Orifice, 110 Degree Flooding Tip Brass/Plastic Boominator nozzle, model 1200BPS Ball Check Strainer, #2 Orifice, 105 Degree Flooding Tip 120" 192" 200" US Gal. Polyethylene N/A 1.4 gpm Open Flow, Viton Valves, Santoprene Diaphragm, 45 psi Internal By-pass, 12 vdc 10' Fold-up Ball Check Strainer, #2 Orifice, 105 Degree Flooding Tip 200" gpm Open Flow, Viton 25 US Gal. Polyethylene 13.00/ Valves, Santoprene Diaphragm, 45 psi Internal By-pass, 12 vdc 10' Spring Loaded Quick Change With Ball Check Strainers, #3 Orifice, 110 Degree Fan Tip 180" gpm Open Flow, Viton 25 US Gal. Polyethylene 13.00/ Valves, Santoprene Diaphragm, 45 psi Demand Switch, 12 vdc N/A Brass/Plastic Boominator nozzle, model 1200BPS 192" US Gal. Polyethylene N/A 1 gpm Open Flow, Viton Valves, Santoprene Diaphragm, 40 psi demand Switch, 12 vdc N/A N/A N/A

16 16 PUMP ASSEMBLY USED ON SPRAYER , , , AND PLUG #12 REPLACES THESE PARTS FOR SPRAYER VALVE PLST.75 FGHT X.75 MGHT 1 10 GAUGE PRESSURE PSI.25 NPTM 1 9 ADAPTOR NYLON.75 MGHT X.50 NPTM 2 8 VALVE PLAST.75 FGHT X.75 MGHT DOUBLE 1 7 TEE NYLON.50 NPTF X.25 NPTF 1 6 WASHER VINYL.62 ID X 1.0 OD X.13 THK 3 5 NIPPLE REDUCER NYLON.50 X BARB NYLON.375 FLAT SEAT 3 3 NUT SWIVEL NYLON KNURLED ELBOW NYLON.375 NPT X PUMP SHURFLO 1 No. Description Qty PUMP ASSEMBLY USED ON SPRAYER AND VALVE PLST.75 FGHT X.75 MGHT 1 11 ADAPTOR NYLON.75 MGHT X.50 NPTM 2 10 VALVE PLAST.75 FGHT X.75 MGHT 1 DOUBLE 9 TEE NYLON.50 NPTF X.25 NPTF 1 8 WASHER VINYL.62 ID X 1.0 OD X.13 THK 3 7 GAUGE PRESSURE PSI.25 NPTM 1 6 NIPPLE REDUCER NYLON.50 X ELBOW NYLON.25 NPT STREET 1 4 BARB NYLON.375 FLAT SEAT 3 3 NUT SWIVEL NYLON KNURLED PUMP SHURFLO 1 1 ELBOW NYLON.375 NPT X.50 1 No. Description Qty

17 PUMP RED BLACK BLACK RED SPRAYER 25 GAL PULL TYPE ITEM # ASSY DETAIL 38

18 PARTS LIST SPRAYER 25 GAL PULL TYPE ITEM # No. Item No. Description Qty BOOM LEFT ARM INSIDE BOLT HEX UNC X.75 LG NUT HEX UNC GR 5 PTD WASHER PTD.281 ID X.625 OD BOOM ARM LEFT OUTSIDE NUT LOCK NOZZLE BODY NYLON.688 FPS FUSE BOX INLINE 14 GA C/W 10A HOSE CLEAR BRAIDED.375 ID X.59 OD X 39" LG BOLT HEX UNC X 1.75 LG GR 5 PTD FRAME BOOM WASHER PTD.687 ID X 1.75 OD WHEEL 4.10/ X.625 AXLE NUT LOCK UNITORQ UNC BOLT HEX UNC X.625 LG GR 5 PTD WASHER LOCK SPLIT REG.312 PTD WASHER PTD.344 ID X.688 OD FRAME 25 GAL SPRAYER BOLT HEX UNC X 1.00 LG GR 5 PTD FRAME TOW S/ASSY DECAL SPRAYER CAUTION GAUGE PRESSURE PSI.25 NPTM WIRE ELEC. RED 14 GA X 6 FT TEE NYLON.50 NPTF X.25 NPTF SWITCH TOGGLE 15 AMP 125DCV BARB.375 X.688 THREAD ELBOW NYLON.375 NPT X PUMP SHURFLO HOLDER SWITCH ON/OFF PLATE ADAPTOR NYLON.75 MGHT X.50 NPTM VALVE PLAST.75 FGHT X.75 MGHT DOUBLE CLIP GRIPPER RANGE HOSE CLEAR BRAIDED.375 ID X.59 OD X 19.5" LG SCR MACH RD HD #10-24 UNC X 1.00 LG BARB NYLON.375 FLAT SEAT NUT SWIVEL NYLON KNURLED ELBOW NYLON.687 MPS X.50 BARB CLAMP HOSE NYLON 19/ FILTER BALL CHECK NOZZLE 100 MESH O RING BN.625 X NOZZLE DEFLECTIP RED NUT NOZZLE SEAT CAP NYLON.688 MPS BOOM ARM RIGHT OUTSIDE STRAINER 50 MESH.330 ID BARB NYLON.375 X CLAMP HOSE NYLON GROMMET RUBBER.75 ID X 1.38 OD HOSE CLEAR BRAIDED.50 ID X.75 OD X 30" LG HOSE CLEAR BRAIDED.375 ID X.59 OD X 19.5" LG BOOM RIGHT ARM INSIDE 1

19 TEE NYLON NOZZLE SEAT BARB NYLON.375 TEE INSERT SQ RIBBED 1.00 X BOLT CARR UNC X 1.00 LG GR 5 PTD FRAME SLIDE BOOM WASHER LOCK SPLIT REG.25 PTD NUT WING UNC PTD NON STAMP TYPE HOSE CLEAR BRAIDED.375 ID X.59 OD X 210" LG WAND SPRAYER C/W ADJ. TIP SCR MACH RD HD #10-24 UNC X.31 LG VALVE PLST.75 FGHT X.75 MGHT WASHER VINYL.62 ID X 1.0 OD X.13 THK NIPPLE REDUCER NYLON.50 X HOSE CLEAR BRAIDED.375 ID X.59 OD X 27" LG WIRE ELEC. BLACK 14 GA X 6 FT SCREW THUMB BLACK PIN.375 X 2.5 USEABLE LENGTH CABLE TIE NYLON TANK 25 GAL BLOW MOLDED DECAL PAL SERIAL # COTTER PIN.187 X 1.50 PLAIN DECAL SPRAYER 25 GAL POWERFIST 1 19

20 SPRAYER 25 GAL DELUXE ITEM # PUMP RED BLACK BLACK RED

21 PARTS LIST SPRAYER 25 GAL PULL TYPE DELUXE ITEM # No. Item No. Description Qty ELBOW NYLON NOZZLE BODY HOSE CLEAR BRAIDED.375 ID X.59 OD X 29" LG VALVE PLAST.75 FGHT X.75 MGHT DOUBLE ARM OUTSIDE BOOM RIGHT 10 FT NUT SWIVEL NYLON KNURLED WASHER VINYL.62 ID X 1.0 OD X.13 THK SPRING TENSION 1.00 OD X 5.0 LG HOSE CLEAR BRAIDED.375 ID X.59 OD X 31" LG CLAMP HOSE NYLON HOSE CLEAR BRAIDED.375 ID X.59 OD X 29 " LG GROMMET RUBBER.75 ID X 1.38 OD INSERT SQ RIBBED 1.00 X BOLT HEX UNC X 2.75 LG GR 5 PTD FRAME SLIDE BOOM SPACER BOOM CROSS NYLON NOZZLE BODY SCREW THUMB BLACK FRAME MIDDLE BOOM 10 FT TEE NYLON NOZZLE BODY WAND SPRAYER C/W ADJ. TIP ARM OUTSIDE BOOM LEFT 10 FT CLAMP STEEL 1" SQ TUBE NOZZLE CAP NOZZLE QUICK DETACH INSERT SQ RIBBED 1.00 X PIN.375 X 2.5 USEABLE LENGTH HOSE CLEAR BRAIDED.375 ID X.59 OD X 210" LG FRAME BOOM WASHER PTD.812 ID X OD X.134 THK TIRE 13/5.00X6 TURF BOLT HEX UNC X.625 LG GR 5 PTD WASHER LOCK SPLIT REG.312 PTD WASHER PTD.344 ID X.688 OD FRAME TOW S/ASSY DECAL PAL SERIAL # BOLT HEX UNC X 1.00 LG GR 5 PTD FRAME 25 GAL DELUXE NUT LOCK UNITORQ UNC TANK 25 GAL BLOW MOLDED BARB.375 X.688 THREAD SWITCH TOGGLE 15 AMP 125DCV HOLDER SWITCH ELBOW NYLON.375 NPT X ON/OFF PLATE PUMP SHURFLO SCR MACH RD HD #10-24 UNC X 1.00 LG NIPPLE REDUCER NYLON.50 X TEE NYLON.50 NPTF X.25 NPTF BARB NYLON.375 FLAT SEAT CLAMP HOSE NYLON 19/ HOSE CLEAR BRAIDED.375 ID X.59 OD X 19.5" LG 1

22 NOZZLE FAN TIP BLUE GASKET RUBBER.750 OD X.344 ID X.150 THK FILTER BALL CHECK NOZZLE 100 MESH VALVE PLST.75 FGHT X.75 MGHT ADAPTOR NYLON.75 MGHT X.50 NPTM GAUGE PRESSURE PSI.25 NPTM HOSE CLEAR BRAIDED.50 ID X.75 OD X 30" LG BARB NYLON.375 X STRAINER 50 MESH.330 ID FUSE BOX INLINE 14 GA C/W 10A WIRE ELEC. BLACK 14 GA X 6 FT WIRE ELEC. RED 14 GA X 6 FT CLIP GRIPPER RANGE SCR MACH RD HD #10-24 UNC X.31 LG DECAL SPRAYER CAUTION COTTER PIN.187 X 1.50 PLAIN BOLT HEX UNC X 1.75 LG GR 5 PTD DECAL SPRAYER 25 GAL POWERFIST 1 22

23 23 SPRAYER 25 GAL 3 PT HITCH ITEM # ASSY DETAIL RED RED + PUMP BLACK 65 BLACK

24 PARTS LIST SPRAYER 25 GAL 3 PT HITCH ITEM # No. Item No. Description Qty BOOM ARM RIGHT OUTSIDE NUT HEX UNC GR 5 PTD HOSE CLEAR BRAIDED.375 ID X.59 OD X 210" LG BOOM RIGHT ARM INSIDE CLAMP HOSE NYLON 19/ TEE NYLON NOZZLE SEAT SCREW THUMB BLACK NUT WING UNC PTD NON STAMP TYPE WASHER LOCK SPLIT REG.25 PTD WASHER PTD.281 ID X.625 OD FRAME SLIDE BOOM BARB NYLON.375 TEE HOSE CLEAR BRAIDED.375 ID X.59 OD X 17"LG BOLT CARR UNC X 1.00 LG GR 5 PTD VALVE PLST.75 FGHT X.75 MGHT ADAPTOR NYLON.75 MGHT X.50 NPTM BARB NYLON.375 FLAT SEAT HOSE CLEAR BRAIDED.375 ID X.59 OD X 19.5" LG BOOM LEFT ARM INSIDE VALVE PLAST.75 FGHT X.75 MGHT DOUBLE WASHER VINYL.62 ID X 1.0 OD X.13 THK NUT SWIVEL NYLON KNURLED TEE NYLON.50 NPTF X.25 NPTF NIPPLE REDUCER NYLON.50 X HOSE CLEAR BRAIDED.375 ID X.59 OD X 19.5 " LG SCR MACH RD HD #10-24 UNC X 1.00 LG BOLT HEX UNC X.75 LG BOOM ARM LEFT OUTSIDE ON/OFF PLATE WAND SPRAYER C/W ADJ. TIP ELBOW NYLON.375 NPT X HOLDER SWITCH BARB.375 X.688 THREAD PUMP SHURFLO SWITCH TOGGLE 15 AMP 125DCV ELBOW NYLON.25 NPT STREET SCR MACH RD HD #10-24 UNC X.31 LG CLIP GRIPPER RANGE TANK 25 GAL BLOW MOLDED FRAME S/ASSY 3 PT HITCH PIN TOP LINK PIN LINCH.438 DIA PIN LIFT ARM.875 DIA X 1.75 LG TYPE A NUT LOCK UNITORQ UNC BOLT HEX UNC X.625 LG GR 5 PTD WASHER LOCK SPLIT REG.312 PTD WASHER PTD.344 ID X.688 OD FRAME BOOM BOLT HEX UNC X 1.75 LG GR 5 PTD 2

25 PIN.375 X 2.5 USEABLE LENGTH STRAINER 50 MESH.330 ID BARB NYLON.375 X HOSE CLEAR BRAIDED.50 ID X.75 OD X 30" LG GROMMET RUBBER.75 ID X 1.38 OD HOSE CLEAR BRAIDED.375 ID X.59 OD X 39" LG ELBOW NYLON.687 MPS X.50 BARB NUT LOCK NOZZLE BODY NYLON.688 FPS O RING BN.625 X FILTER BALL CHECK NOZZLE 100 MESH NOZZLE DEFLECTIP RED NUT NOZZLE SEAT CAP NYLON.688 MPS GAUGE PRESSURE PSI.25 NPTM CLAMP HOSE NYLON FUSE BOX INLINE 14 GA C/W 10A WIRE ELEC. BLACK 14 GA X 6 FT WIRE ELEC. RED 14 GA X 6 FT DECAL PAL SERIAL # CABLE TIE NYLON DECAL SPRAYER CAUTION INSERT SQ RIBBED 1.00 X DECAL SPRAYER 25 GAL POWERFIST 1 25

26 SPRAYER 25 GAL PULL TYPE BOOMINATOR ITEM # PUMP RED BLACK BLACK RED

27 PARTS LIST SPRAYER 25 GAL PULL TYPE BOOMINATOR ITEM # No. Item No. Description Qty FRAME BOOM BOLT HEX UNC X 1.75 LG GR 5 PTD NUT LOCK UNITORQ UNC SCREW THUMB BLACK HOLDER BOOMINATOR NOZZLE CHECK VALVE BRASS.25 NPTF NOZZLE BRASS BOOMINATOR DECAL SPRAYER 25 GAL POWERFIST CLAMP HOSE NYLON 19/ NUT SWIVEL NYLON KNURLED BARB NYLON.375 FLAT SEAT WASHER VINYL.62 ID X 1.0 OD X.13 THK VALVE PLST.75 FGHT X.75 MGHT ADAPTOR NYLON.75 MGHT X.50 NPTM 2 15 BARB B.375 X.25 NPTM WAND SPRAYER C/W ADJ. TIP GAUGE PRESSURE PSI.25 NPTM PUMP SHURFLO 3.0 GPM TEE NYLON.50 NPTF X.25 NPTF VALVE PLAST.75 FGHT X.75 MGHT DOUBLE HOSE CLEAR BRAIDED.50 ID X.75 OD X 30" LG CLAMP HOSE NYLON ON/OFF PLATE HOLDER SWITCH HOSE CLEAR BRAIDED.375 ID X.59 OD X 29" LG GROMMET RUBBER.75 ID X 1.38 OD STRAINER 50 MESH.330 ID BARB.375 X.688 THREAD ELBOW NYLON.50 NPTF X.50 BARB SWITCH TOGGLE 15 AMP 125DCV DECAL SPRAYER CAUTION SCR MACH RD HD #10-24 UNC X.31 LG CLIP GRIPPER RANGE TANK 25 GAL BLOW MOLDED FRAME 25 GAL DELUXE DECAL PAL SERIAL # FRAME TOW S/ASSY BOLT HEX UNC X 1.00 LG GR 5 PTD WASHER PTD.344 ID X.688 OD WASHER LOCK SPLIT REG.312 PTD BOLT HEX UNC X.625 LG GR 5 PTD WASHER PTD.812 ID X OD X.134 THK TIRE 13/5.00X6 TURF COTTER PIN.187 X 1.50 PLAIN WIRE ELEC. RED 14 GA X 6 FT SCR MACH RD HD #10-24 UNC X 1.00 LG BARB NYLON.375 X WIRE ELEC. BLACK 14 GA X 6 FT HOSE CLEAR BRAIDED.375 ID X.59 OD X 210" LG HOSE CLEAR BRAIDED.375 ID X.59 OD X 29" LG FUSE BOX INLINE 14 GA C/W 15A 1 27

28 28 SPRAYER 15 GAL SPOT ITEM # FUSE SWITCH BROWN WIRING DIAGRAM 30 QUICK COUPLER RED BATTERY BLACK - +

29 PARTS LIST SPRAYER 15 GAL SPOT ITEM # No. Item No. Description Qty WAND SPRAYER C/W ADJ. TIP HOSE CLEAR BRAIDED.375 ID X.59 OD X 200" LG NUT SWIVEL NYLON KNURLED BARB NYLON.375 FLAT SEAT WASHER VINYL.62 ID X 1.0 OD X.13 THK VALVE PLAST.75 FGHT X.75 MGHT DOUBLE ADAPTOR NYLON.75 MGHT X.50 NPTM PLUG HEX NYLON.50 NPTM TEE NYLON.50 NPTF X.25 NPTF GAUGE PRESSURE PSI.25 NPTM WEB 1" NYLON STRAPS 5 FT LG TANK 15 GAL BLOW MOLDED BARB.375 X.688 THREAD ELBOW NYLON.375 NPT X CLAMP HOSE NYLON HOSE CLEAR BRAIDED.375 ID X.59 OD X 18.38"LG PUMP W/SWITCH SHURFLO SCR MACH RD HD #10-24 UNC X 1.00 LG BARB NYLON.375 X HOSE CLEAR BRAIDED.50 ID X.75 OD X 24" LG STRAINER 50 MESH.330 ID NIPPLE REDUCER NYLON.50 X CLAMP HOSE NYLON 19/ CLIP GRIPPER RANGE SCR MACH RD HD #10-24 UNC X.31 LG DECAL PAL SERIAL # DECAL SPRAYER 15 GAL POWERFIST DECAL SPRAYER CAUTION GROMMET RUBBER.75 ID X 1.38 OD WIRE ELEC. DOUBLE 14 GA X 6 FT 1

30 30 SPRAYER 15 GAL ATV BOOMINATOR ITEM # FUSE SWITCH BROWN 31 QUICK COUPLER BATTERY BLACK WIRING DIAGRAM RED

31 PARTS LIST SPRAYER 15 GAL ATV BOOMINATOR ITEM # No. Item No. Description Qty BOLT HEX UNC X.625 LG GR 5 PTD WASHER LOCK SPLIT REG.312 PTD WASHER PTD.344 ID X.688 OD FRAME TANK ATV BOLT HEX UNC X.750 LG GR 5 PTD BRACKET EXTENDING BOOM RIGHT STRAINER 50 MESH.330 ID TANK 15 GAL BLOW MOLDED DECAL PAL SERIAL # BARB NYLON.375 X CLIP GRIPPER RANGE SCR MACH RD HD #10-24 UNC X.31 LG HOSE CLEAR BRAIDED.375 ID X.59 OD X 50" LG WAND SPRAYER C/W ADJ. TIP BARB.375 X.688 THREAD CLAMP HOSE NYLON VALVE PLST.75 FGHT X.75 MGHT ADAPTOR NYLON.75 MGHT X.50 NPTM GAUGE PRESSURE PSI.25 NPTM ELBOW NYLON.25 NPT STREET TEE NYLON.50 NPTF X.25 NPTF NUT SWIVEL NYLON KNURLED BARB NYLON.375 FLAT SEAT WASHER VINYL.62 ID X 1.0 OD X.13 THK VALVE PLAST.75 FGHT X.75 MGHT DOUBLE CLAMP HOSE NYLON 19/ HOSE CLEAR BRAIDED.375 ID X.59 OD X 18.38" LG SCR MACH RD HD #10-24 UNC X 1.00 LG PUMP W/SWITCH SHURFLO ELBOW NYLON.375 NPT X WIRE ELEC. DOUBLE 14 GA X 6 FT NIPPLE REDUCER NYLON.50 X GROMMET RUBBER.75 ID X 1.38 OD HOSE CLEAR BRAIDED.50 ID X.75 OD X 24" LG WEB 1" NYLON STRAPS 5 FT LG NUT LOCK UNITORQ UNC DECAL SPRAYER CAUTION BRACKET EXTENDING BOOM LEFT SUPPORT S/ASSY BOOM HOSE CLEAR BRAIDED.375 ID X.59 OD X 200" LG SCREW THUMB BLACK NUT LOCK UNITORQ UNC HOLDER BOOMINATOR NOZZLE CHECK VALVE BRASS.25 NPTF NOZZLE BRASS BOOMINATOR BOLT HEX UNC X 1.50 LG GR 5 PTD BARB B.375 X.25 NPTM DECAL SPRAYER 15 GAL POWERFIST 1

32 SPRAYER 15 GAL PULL TYPE ITEM # RED PUMP RED BLACK 48 - BLACK

33 PARTS LIST SPRAYER 15 GAL PULL TYPE ITEM # No. Item No. Description Qty HOSE CLEAR BRAIDED.375 ID X.59 OD X 18.38"LG CLAMP HOSE NYLON 19/ NUT SWIVEL NYLON KNURLED BARB NYLON.375 FLAT SEAT NOZZLE DEFLECTIP GRAY VALVE PLAST.75 FGHT X.75 MGHT DOUBLE ADAPTOR NYLON.75 MGHT X.50 NPTM SCR MACH RD HD #10-24 UNC X 1.00 LG GAUGE PRESSURE PSI.25 NPTM NIPPLE REDUCER NYLON.50 X PUMP SHURFLO ON/OFF PLATE HOLDER SWITCH SWITCH TOGGLE 15 AMP 125DCV HOSE CLEAR BRAIDED.50 ID X.75 OD X 24" LG GROMMET RUBBER.75 ID X 1.38 OD BARB.375 X.688 THREAD TANK 15 GAL BLOW MOLDED BOLT HEX UNC X 1.00 LG GR 5 PTD FRAME TOW S/ASSY FRAME S/ASSY BOLT HEX UNC X.750 LG GR 5 PTD WASHER LOCK SPLIT REG.312 PTD WASHER PTD.344 ID X.688 OD WASHER VINYL.62 ID X 1.0 OD X.13 THK NUT WELD SINGLE TAB.312 UNC WHEEL 4.10/ X.625 AXLE WASHER PTD.812 ID X OD X.134 THK HOSE CLEAR BRAIDED.375 ID X.59 OD X 27" LG ELBOW NYLON.687 MPS X.50 BARB NUT LOCK NOZZLE BODY NYLON.688 FPS FILTER BALL CHECK NOZZLE 100 MESH O RING BN.625 X NUT NOZZLE SEAT CAP NYLON.688 MPS CLAMP STEEL FOR.75 PIPE BOOM PIPE FRAME BOOM U BOLT 1.00 X UNC BARB NYLON.375 TEE CABLE TIE NYLON TEE NYLON.50 NPTF X.25 NPTF CLAMP HOSE NYLON ELBOW NYLON.375 NPT X BARB NYLON.375 X STRAINER 50 MESH.330 ID 1

34 NUT LOCK UNITORQ UNC FUSE BOX INLINE 14 GA C/W 10A WIRE ELEC. BLACK 14 GA X 6 FT WIRE ELEC. RED 14 GA X 6 FT DECAL PAL SERIAL # CLIP GRIPPER RANGE SCR MACH RD HD #10-24 UNC X.31 LG DECAL SPRAYER CAUTION VALVE PLST.75 FGHT X.75 MGHT HOSE CLEAR BRAIDED.375 ID X.59 OD X 200" LG WAND SPRAYER C/W ADJ. TIP NUT LOCK NYLON UNC DECAL SPRAYER 15 GAL POWERFIST COTTER PIN.187 X 1.50 PLAIN 2 34

35 35 SPRAYER 15 GAL SPOT ITEM # SWITCH BROWN 18 QUICK COUPLER BATTERY BLACK - + WIRING DIAGRAM RED

36 PARTS LIST SPRAYER 15 GAL SPOT ITEM # No. Item No. Description Qty 1 HOSE.375 ID X 200" LG WAND SPRAYER C/W ADJ. TIP PUMP SHURFLO AUTO DEMAND WASHER PTD.219 ID X.500 OD X.049 THK SCR MACH RD HD #10-24 UNC X.625 LG COMBINATION DRIVE CLAMP SCR SS.312 TO HOSE.375 ID X 20" LG GROMMET RUBB.688 ID X OD BARB NYLON.375 X STRAINER 50 MESH.330 ID DECAL PAL SERIAL # DECAL SPRAYER CAUTION DECAL SPRAYER 15 GAL POWERFIST TANK 15 GAL BLOW MOLDED SCR MACH RD HD #10-24 UNC X.31 LG CLIP GRIPPER RANGE PLUG PLASTIC # WIRE ELEC. DOUBLE 14 GA X 6 FT 1