VALORE SEVEN. Serial Number. Pacific) Version No.:V

Transcription

1 VALORE SEVEN Version No.:V Serial Number Pacific)

2 7 9 8 " 5 8 " " " 26 2 " 7 8 " 9" 2 8 " 2 8 " (H) 26.9" x (W) 8.26" x (D) 8.85" Hand shower hose: 59.05" Weight: Net: 0 lbs /Gross: 2 lbs BEFORE USAGE Optional drill-less design and installs in under one hour Sleek, slim contemporary design Large embedded body jet 50-silicone nozzle"rainfall" shower head German engineered diverter with 6 distinct spray modes Full brass hand shower and cradle Compatibe with most shower stalls and tub/shower enclosures High quality metal components Read this Installation and User Guide before installing and operating. Always take extra care when installing to prevent injury. Wear appropriate safety equipment. Do not allow children unsupervised use of the shower panel. Do not use the shower panel if you are physically impaired or under the influence of alcohol or any substance which may prevent you from properly operating the shower panel. Keep enough distance between yourself and the shower panel. Do not allow sensitive parts of the body such as eyes to come too close to the shower jets. Proper pressure balance needs to be maintained between hot and cold water inputs to prevent scalding or injury

3 BEFORE INSTALLATION Before and during installation, read and familiarize yourself with all installation instructions for this product. Keep all components, parts and accessories of this product away from small children and minors. During installation, all screws, tools and small parts should be supervised so that they do not fall into the hands of children. Use caution at all times when installing this product. Ensure that you are physically able to perform all parts of the installation and that you have the correct tools and equipment needed. Before beginning,remove all wrappers and packinging materials including staples and packing straps. Check to ensure that all components and parts are complete. The Filter Gasket (#0) must be installed to protect against incoming dirt by pipework. Incoming dirt can impair the function and/or lead to damages on functional parts of the fixture. Manufacturer will not be held liable for resulting damages. The O Ring Gasket (# 2) must be installed to prevent water leakage. Manufacturer will not be responsible or liable from any damage which results directly or indirectly from failure to installation of the O Ring Gasket. Sealing Tape Silicone Pencil Shear - -

4 Description Bottom Shower Panel Casing Top Shower Panel Casing Shower Head Ring Clamp White Top Hose Screws Top Cover Shower Head Outlet Connector Cover Elbow Connector Filter Gasket Brass Extender Joint (-7/8"&2-/"x/2") Flow Regulator Base Plate Cover with Tape ( for Shower Head Outlet Connector Cover) Gray Main PVC Supply Line Screws Nut Brass Nut Rubber Washer( -/2") Screws Screw Anchor Positioning and Support Brackets Full Brass Handshower Handshower Hose O Ring Gasket Handshower Cradle Assembly Jet Diverter Knob Diverter Valve Qty Set Set Pc 2 Pcs Pc 6 Psc Pc Pc Pc 2 Pcs 2 Pcs Pc Pc Pc Pcs Pcs 2 Pcs 2 Pcs 2 Pcs 2 Pcs Pc Pc Set 2 Pcs Pc Pc Pc Pc - -

5

6 HAND SHOWER AND CRADLE ASSEMBLY a b

7 e TOP COVER ASSEMBLY f PH + 2 PH Note: The hose connecting the shower head is in white color. g h PH I - 7 -

8 INSTALLATION INSTRUCTIONS Before Installation, ensure there is sufficient clearance to accommodate the shower panel. A minimum of 2.5" is required between the shower outlet and top of your existing valve. Ensure that the water line to the overhead shower pipe is completely shut off prior to performing any work. Min 2.5Inch Remove your existing shower head.then remove your existing shower arm ½" diameter is needed to accommodate the shower panel's Brass Extender Joint (Part #) Two brass extender joints (Part #) are included with this shower panel. Test both extender joints to see which joint will provide you a minimum of 5/8'' from the wall. Use the plumbing tape and wrap the threaded part of the brass extender joint (Part #) on both ends. MAX 5/8" Place the flow regulator (Part #2) into the appropriate extender joint (Part #), ensure the flow regulator's direction is right as diagram indicating, ensure the longer end of threading on the extender joint is facing outward. Note: The flow regulator (Part #2) is required to be installed as some states in the U.S. require a flow rate of 2.0GPM. You can choose to install the flow regulator based on the requirements of state or local plumbing codes Flow Regulator - 8 -

9 Bracket installation options: INSTALLATION INSTRUCTIONS When the overhead shower outlet is located outside shower surface, use the Method (Drilled installation). When the overhead shower outlet is located inside the shower surface, use the Method 2 (Drill-less installation). Method : Drilled installation instructions. Place shower panel against the wall in its desird permanent location. 2. Mark Line ane Line 2: - Mark the bottom of the panel with a pencil or erasable marker.(line ) - Mark a second line (Line 2) which 9.86 inch is above and parallel to Line. - Place the bottom of the mounting bracket flush against Line 2 and hold flat against the shower surface.. To ensure the bracket will be in a straight abd level position, use a level tool against the side of the bracket to make fine adjustments to the bracket position until fully level.. Using a pencil or erassable market, mark drill holes A and B. 2 Shower outlet Shower outlet Recommended 0" Bracket Level H M 2 H M 2 L Line 2 L 9.86" B Line H 2 M L A - 9 -

10 INSTALLATION INSTRUCTIONS Method Note: Before drilling make sure you have the correct drill bit for your shower surface. 5. Drill the 2 screw holes with a 6mm bit suitable for the wall surface. Warning: Ensure your shower water line is not directly behind the drilling points A and B. Drilling into the water supply line may cause extensive damage. 6. Install the anchors(part #20), Seal the wall around the nipple and the anchors with waterproof. silicone. 7. After anchor screws have been installed, affix the Positioning & Support Brackets (Part #2) using supplied Screws (Part #9). B B Silicone 9 x2pcs PH + 2 A 20 x2pcs A 8. Hose shearing instructions a. Grasping the PVC supply line, extend the PVC supply line straight over the shower head outlet. b. Mark the PVC supply line where it intersects the bottom of the shower head outlet. c. Shear the excess PVC supply line at the mark. a b c Shear Line - 0 -

11 INSTALLATION INSTRUCTIONS 9.Connecting the Supply Line Elbow (Part #9) to the main PVC Supply Line (Part #): a a. Insert the Ring Clamp (Part #) onto the end of Gray PVC Supply Line (Part #). b. Fully insert the grooved end of the Elbow Connector (Part #9) into the Gray PVC Supply Line (Part #). 9 c. With a Phillips head screwdriver, tighten the bolt and nut on the Hose Clamp (Part #) until the Gray PVC Supply Line is secured to Elbow Connector (Part #9). 9 b d. The Elbow Connector (Part #9) will be secured to the Brass Extender Joint (Part #) in a later step. 9 c PH + 0. Install the PVC cover. a. Peel off the paper backing to the adhesive ring for the Base Plate cover (Part #). (Note: Clear all residues to ensure the cover will bond properly) a b b. Place the adhesive side to the wall and apply pressure to secure the Base Plate Cover (Part #). c. Add a Filter Gasket (Part #0) into Elbow Joint (Part #9) first.then attach the Elbow Joint (Part #9) to the Brass Extender Joint (Part #), turn clock wise to tighten. c d d. Place the Showerhead Cover (Part #8) to conceal plumbing fixture

12 INSTALLATION INSTRUCTIONS. Install the shower panel: After all connections have been completed inside the shower panel, it is ready to be hung on the shower wall for installation. a. Place the shower panel on the desired bracket position you previously selected. b. Raise the shower panel and rest it againg the bracket until the support strut is resting sungly in the desired bracket position. c.once a snug and secure fit is achieved and all parts of the PVC Supply Line are secured to the back of the shower panel, verify that water is flowing normally prior to sealing the panel. Sealant may be applied to seal the gap between the shower panel boby and the wall to prevent water from entering behind the shower panel. 2 Silicone Method 2: Drill-less Installation Instruction. Place the Bracket (Part #2) Insert the Bracket (Part #2) onto the Brass Extender Joint (Part #) 2 To ensure the bracket will be in straight and level position, use a level tool against the side of the bracket make fine adjustments to the bracket position until fully level. Once fully level, this will be the final position of the bracket guide. 2 Take a pencil/marker and lightly mark the vertical position of the Bracket (Part #2)

13 INSTALLATION INSTRUCTIONS Note: Prior to applying bracket clean all residues from the wall bond properly. Recommend to use, cider vinegar, alcohol, or mineral dissolve. Peel off the paper backing to the adhesive on the back side of the Bracket (Part #2). a b c Place the adhesive side to the wall and apply pressure to secure the Bracket(Part #2). 8 7 Place the Rubber Washer (Part #8) and nut (Part #7) over the Brass Extender Joint (Part #), and tighten the nut to secure the bracket (Part #2) to the extender joint Shear the Gray PVC Supply Line (Part #) Installation position will vary, depending on your shower space clearance. If you install(h,m,l): H - shear 8.58" length of the Gray PVC Supply Line. M - shear 5.2" length of the Gray PVC Supply Line. L - shear.8" length of the Gray PVC Supply Line. There are positions in the bracket: High, Medium, Low. Depending on which position you choose; you will need the Shear excess gray PVC Supply Line. Recommended 0" H 8.58" M 5.2" L.8" H Shear M L - -

14 INSTALLATION INSTRUCTIONS.Connecting the Supply Line Elbow (Part #9) to the main PVC Supply Line (Part #): a 5 a. Insert the Ring Clamp (Part #) onto the end of Gray PVC Supply Line (Part #). b. Fully insert the grooved end of the Elbow Connector (Part #9) into the Gray PVC Supply Line (Part #). c. With a Phillips head screwdriver, tighten the bolt and nut on the Hose Clamp (Part #) until the Gray PVC Supply Line is secured to Elbow Connector (Part #9). 9 b 9 d. The Elbow Connector (Part #9) will be secured to the Brass Extender Joint (Part #) in a later step. 9 c PH +. Install the shower panel. 6 a. Add a Filter Gasket (Part #0) into Elbow Joint (Part #9) first.then attach the Elbow Joint (Part #9) to the Brass Extender Joint (Part #), turn clock wise to tighten. After all connections have been completed inside the shower panel, it is ready to be hung on the shower wall for installation. b. Place the shower panel on the desired bracket position you previously selected. c. Raise the shower panel and rest it against the bracket until the support strut is resting snugly in the desired bracket position d. Once a snug and secure fit is achieved and all parts of the PVC Supply Line are secured to the back of the shower panel, verify that water is flowing normally prior to sealing the panel. Silicone Sealant may be applied to seal the gap between the shower panel boby and the wall to prevent water from entering behind the shower panel. - -

15 psi 80 0 a b Dual Spray Modes Jet Spray Position When the selector knob is placed in between two operating, this will result in a to simultaneous operation of both adjustment spray modes. A slight reduction in water pressure may occur due to the shared water flow between the two spray modes. When the position knob is placed in d, the handshower and the top hydro jets will work simultaneously. c d - 5 -

16 Diverter Valve Structure 5 Diverter valve 2 How to Remove the Diverter Valve 2 (2.5 mm) 2 Remove the cover (Part #) to open the set screw access hole. Loosen the set screw (Part #) from the valve stem and pull the knob (Part #2) straight out. 5 Diverter valve Loosen and remove the gland nut (Part #) Remove the Diverter valve (Part #5) by pulling it straight out.

17 How to Install the Diverter Valve 22 5 Diverter valve Place the Diverter valve (Part #5) into the valve body. Note the one pillar on the bottom of the Diverter valve (Part#5) must be aligned with the hole in the rear of the body. Adjust the knob with right position Tighten the gland nut (Part #). Take precaution to avoid scratching the trim plate. Do not force the nut too tightly. Shower Head Mode Place the knob (Part #2) on the valve stem. Before securing the knob, turn on the water to know which way the handle is to be pointed. 2 (2.5 mm) 5 2 Once the correct position of the knob has been determined, place the knob on the valve stem and tighten the set screw (Part #). Do not overtighten. Place the cover (Part #) and finish the install

18 How to Replace the Check Valve 2 0 Loosen the nut securing the Gary PVC Hose (Part #) to the brass valve body. Disconnect the Gary PVC Hose (Part #) from the valve body and remove the Filter Gasket (Part #0). 2 2 Check Valve Check Valve Using needle nose pliers, grip the edge of the check valve and pull straight out.. Place the new check valve into the valve body. Observe the direction of the valve is correct Level 0 Ensure the check valve is flush with the top of the valve body inlet. Place the filter gasket (Part #0) back in place and secure the Gary PVC Hose (Part #) to the valve body to complete the install

19 - 9 -

20 Ten (0) years guaranteed from manufacture defects. Lifetime limited parts warranty on the diverter valve. Recycling: Most of the materials used to manufacture this shower fixture are recyclable. Please dispose of those materials properly in accordance to your local state laws. Improper disposing of this shower fixture can be harmful to the environment