Visit Crimpsource at your online resource for hose crimp specifications. Equipment

Transcription

1 Visit rimpsource at your online resource for hose crimp specifications.

2 atalog 4400 US Visual Index Karrykrimp -8 Karrykrimp ench Mount -8 Karrykrimp 2-10 Karrykrimp 2 ench Mount -10 Parkrimp 2-12 Portable Pumps -14 rimpsource -15 Parkrimp and Twin-Tough Instructions onversion Kits T-115V and Hose ut-off Machine Hose ut-off Machine Karrykut - Hose ut-off Machine -2 Hose Products ivision

3 atalog 4400 US Visual Index Hose ut-off Machine -21 TH6-10-HL TH6-10-L-7-22 TH3-51 Ultra lean Hose leaning Kit conomy Hose leaning Kit TH Handycut - Hose ut-off Machine Push-Lok ut-off & ssembly Tool Hose Insertion epth locks TH V R and 83-0R -25 Hose ut-off Tool Hozembler ie Storage Racks 80-SR -25 TH Swivel ie Rack Fittings Push-On Stand Mandrel Tool Kit and TH2-7M25-6, TH2-7M Mandrel Tool Kit - 23 Mandrels - 25 ssembly Tools Hose Oil -27 Lubricant -27 Hose Perforator Hose Oil ccrolube - High fficiency -3 Hose Products ivision

4 atalog 4400 US Visual Index Small rimper Hood -27 Large rimper Hood Hose Products ivision

5 atalog 4400 US Notes -5 Hose Products ivision

6 atalog 4400 US Parkrimp System Hose ssemblies re asy With the Parkrimp System. Since its introduction in 1980, the Parkrimp family of crimping machines has led the industry in ease of use and rugged durability. When it comes to hose assemblies, no one puts it all together like Parker. From highvolume productivity to portable on-site assembly, we offer a variety of crimping machines, No-Skive hoses, and No-Skive fittings to meet your needs. With Parkrimp equipment, anyone can make factoryquality hose assemblies quickly, easily, and cost effectively. Parkrimp machines are simple to operate and they re built to provide years of dependable service. Seven Parkrimp models an entire family of crimpers are available to meet your benchmounted or portable needs, crimping straight or bent-stem fittings from 1/4" to 2" in diameter. Just use our No-Skive hoses and fittings to create leak-free hose assemblies whenever and wherever you need them. The complete system from one source: No-Skive hose, No-Skive fittings, and crimping machines with worldwide availability and service. ight segment crimp dies provide a smooth, even, 360-degree crimp. ottom-loading operation makes it easy to handle long hose assemblies. With Parkrimp, you benefit from a full length crimp. Our low profile design makes routing hose assemblies easy. Parker s exclusive Parkalign feature positions the fitting in the dies perfectly every time. No-Skive hoses and fittings combine with the Parkrimp system to create high quality, reliable hydraulic hose assemblies every time. Our linked crimp dies keep die segments together. No loose parts to mismatch or misplace. ies are color-coded by size for easy identification and reduced set-up time. e sure to check for the most up to date information and crimp specifications. -6 Hose Products ivision

7 atalog 4400 US Parkrimp System Selecting the right die. Once the proper Parker Hose and Fitting is selected that meets your application requirements, you will need to select the proper die to assemble them together. ased on the hose size and approved fitting, select the proper color coded die, as called out in the chart below. xample: Hose 451T-4 Fitting 43 ie ody olor Silver ie avity olor (-4) R ased on the Parkrimp machine being used to assemble the hose and fitting, individual die part numbers and tooling selection for your assembly can be found in Section of this catalog. For general hose assembly instructions for all Parkrimp machines, please turn to pages -16 and -17. (n instructional video is a standard part of each Parkrimp machine shipped from the manufacturer.) Parker Hose Products ivision also offers a full line of crimping accessories, including conversion kits, cabinets, cut-off saws, push-on tables, die racks, and mandrel tool kits. Hose ash Size ie avity olor ode 43 ie ody olor 70, 71 & 77 ie ody olor 73, 78, S6 & 79 ie ody olor 76 ie ody olor 25 ie ody olor 26 ie ody olor 81 ie ody olor Hose ash Size ie avity olor ode HY ie ody olor Silver lack Olive rab Silver Silver Silver Silver Silver -4 R N/ N/ N/ N/ N/ -4 ROWN -5 PURPL N/ N/ N/ N/ N/ -5 ROWN -6 YLLOW N/ N/ N/ -6 ROWN -8 LU N/ N/ N/ -8 ROWN -10 ORNG N/ N/ N/ N/ -10 ROWN -12 GRN N/ -12 ROWN -16 LK N/ -16 ROWN -20 WHIT N/ N/ -24 R N/ N/ -32 GRN N/ N/ Reference pages -8 through -14 for specific tool information regarding hose, fitting, and crimper combinations. -7 Hose Products ivision

8 atalog 4400 US Karrykrimp Karrykrimp and Karrykrimp ench Mount Karrykrimp ench Mount The Karrykrimp is now available in a modular design with all the familiar Parkrimp System advantages. The same unit now offers portability and bench mountability. apability Up to 1-1/4 I 2 wire braided hose Up to 5/8 I 4 wire spiral hose Only steel fittings Portable, compact rugged design Numerous portable power unit options available Pivoting pusher design for easy die change out Increased height enables longer bent tube fittings to be crimped For use with 25, 26, 43, 81, and HY fittings imensions: 15 wide, 12 deep, 30 high Weight: 60 lbs (without power unit) Rating: 30 ton 10,000 psi maximum Full ycle Time: 30 seconds 82-0P power unit (1/2 43 ) Reference page -14 for information on available power units Standard Part Number Individual 82-H L 82-KK escription Part Number Ä Ä Ä rimp Head 82-H Ä ench Power Unit ssembly 85-ZPH Ä Ä Ä Silver die ring 82-R01 Ä Ä Ä lack die ring 82-R02 Ä Hose ssembly 85-00L Ä Stand ssembly 85-ST apability Up to 1-1/4 I 2 wire braided hose Up to 5/8 I 4 wire spiral hose Only steel fittings Faster cycle times on bench mounted units Pivoting pusher design for easy die change out ompact bench mount design Increased height enables longer bent tube fittings to be crimped For use with 25, 26, 43, 81, and HY fittings imensions: 17 wide, 23 deep, 27-1/2 high Weight: 146 lbs Rating: 30 ton 10,000 psi maximum Full ycle Time: 11 seconds (1/2 43 ) Hydraulic Fluid: W32 oil This unit is designed to make about 400 crimps per day and is not designed to be a production crimper. xceeding these suggested production amounts will significantly reduce the the expectancy of the crimper components. Note: Motor is dual voltage, 50/60hz suitable for /115v, 1ph, 60hz and /110v, 1ph, 50hz. Motor can be rewired by a qualified electrician to operate at alternate voltage. Note: For crimp instructions, see pages -16 and -17. Hose assemblies must be inspected for cleanliness and free of all foreign particles. Parker Hannifin will not accept responsibility for the operation of, or provide warranty coverage for, a crimper that is operated by a power unit other than equipment supplied by Parker Hannifin for the express purpose of operating the crimper. -8 Hose Products ivision

9 atalog 4400 US Karrykrimp and Karrykrimp ench Mount rimp Information Fitting HY HOS Hose Products ivision Lakeland lvd R PUR -6 YL -8 LU -10 ORG -12 GRN -16 LK -20 WHT ie Part Number ST/T ST/T LT ST/T 451ST/T 387/387ST/T (-4 THRU -16 ONLY) 487/487ST/T (-4 THRU -12 ONLY) 421W LT /722ST/T/LT (-6, -8, -10 ONLY) ie Part Number 80-Y06 80-Y ie Ring SILVR LK SILVR ie Part Number FR SILVR ie Part Number 80-V12 80-V16 80-V ie Part Number 80-H H H H H1120 X ie Part Number 80-H H H H H1170 XX SS25UL HT ie Part Number 80-H H H H H H HT aution: Read the operations and technical manual before attempting to operate this machine. o not operate this machine without guard in place. Keep hands clear of moving parts when operating machine. Karrykrimp/Karrykrimp ench Mount Hose ie Selection hart For a new ecal, contact Parker at: PRKR or print your own at ecal Part Number: 82-RIMPL Note: o not use this machine to assemble , 451T-20, 451ST-20 or any size stainless steel fittings. LK SILVR SILVR LK SILVR RV. -9 Hose Products ivision

10 atalog 4400 US Karrykrimp 2 Karrykrimp 2 and Karrykrimp 2 ench Mount Karrykrimp 2 ench Mount The Karrykrimp 2 is now available in a modular design with all the familiar Parkrimp System advantages. The same unit now offers portability and bench mountability. apability Up to 1-1/4 I 2 wire braided hose Up to 1-1/4 I 4 wire spiral hose Up to 1 I 6 wire spiral hose Portable, compact rugged design Numerous portable power unit options available Pivoting pusher design for easy die change out For use with 25,26, 43, 70, 71, 73, 77, 78, 81, and HY fittngs imensions: 14 wide, 14 deep, 31-1/2 high Weight: 120 lbs (without power unit) Rating: 60 ton 10,000 psi maximum Full ycle Time: 20 seconds with 85-0P power unit (1/2 43 series) Reference page -14 for information on available power units Standard Part Number Individual 85-H L 85-KK escription Part Number Ä Ä Ä rimp Head 85-H Ä ench Power Unit ssembly 85-1PH Ä Ä Ä Silver die ring 85-R01 Ä Ä Ä lack die ring 85-R02 Ä Hose ssembly 85-00L Ä Stand ssembly 85-ST apability Up to 1-1/4 I 2 wire braided hose Up to 1-1/4 I 4 wire spiral hose Up to 1 I 6 wire spiral hose Faster cycle times on bench mounted units Pivoting pusher design for easy die change out ompact bench mount design For use with 25, 26, 43, 70, 71, 73, 77, 78, 81, and HY fittings imensions: 17 wide, 23 deep, 28 high Weight: 208 lbs Rating: 60 ton 10,000 psi maximum Full ycle Time: 17 seconds (1/2 43 series) Hydraulic Fluid: W32 oil This unit is designed to make about 400 crimps per day and is not designed to be a production crimper. xceeding these suggested production amounts will significantly reduce the the expectancy of the crimper components. Note: Motor is dual voltage, 50/60hz suitable for /115v, 1ph, 60hz and /110v, 1ph, 50hz. Motor can be rewired by a qualified electrician to operate at alternate voltage. Optional Tooling ie Kit (85-K) Includes 43 dies in sizes 1/4, 3/8, 1/2, 3/4, 1 and 1-1/4 and 70/71 dies in sizes 3/8, 1/2, 3/4, 1, 1-1/4 ONLY. Note: For crimp instructions, see pages -16 and -17. Hose assemblies must be inspected for cleanliness and free of all foreign particles. Parker Hannifin will not accept responsibility for the operation of, or provide warranty coverage for, a crimper that is operated by a power unit other than equipment supplied by Parker Hannifin for the express purpose of operating the crimper. -10 Hose Products ivision

11 atalog 4400 US Karrykrimp 2 & Karrykrimp 2 ench Mount rimp Information Fitting HY HOS Hose Products ivision Lakeland lvd R PUR -6 YL -8 LU -10 ORG -12 GRN -16 LK -20 WHT ie Part Number ST/T T/LT ST/T ST/T ST/T 387/387ST/T (-4 THRU -16 ONLY) 487/487ST/T (-4 THRU -12 ONLY) 421W LT /722ST/T/LT 387/387ST/T (-20 ONLY) 487/487ST/T (-16 ONLY) T ie Part Number F42 (-8 Only) ie Ring SILVR LK LK ie Part Number ST 772T 772LT O NOT US THIS MHIN TO SSML NY 71 SRIS SIZ -20 STINLSS FITTINGS ie Part Number 80-L12 80-L ie Part Number 80-S08 80-S10 80-S ie Part Number 80-L12 80-L16 ie Part Number 80-Y06 80-Y SILVR SILVR LK SILVR SILVR ie Part Number SILVR ie Part Number 80-V12 80-V16 80-V ie Part Number 80-H H H H H H1365 X ie Part Number 80-H H H H H H H1880 XX 772ST T 782ST FR 787T 797T SS25UL HT ie Part Number 80-H H H H H H HT aution: Read the operations and technical manual before attempting to operate this machine. o not operate this machine without guard in place. Keep hands clear of moving parts when operating machine. Karrykrimp 2/Karrykrimp 2 ench Mount Hose ie Selection hart For a new ecal, contact Parker at: PRKR or print your own at ecal Part Number: 85-RIMPL Note: Stainless steel crimp diameters are greater than table listings with the exception of HY series which are greater than table listings. LK SILVR SILVR LK SILVR RV. -11 Hose Products ivision

12 atalog 4400 US Parkrimp 2 Parkrimp 2 apability Standard Up to 2 I 2 wire braided hose Up to 2 I 4/6 wire spiral hose asy to use vertical design rimps full range of Parker hoses from 1/4 through 2 I.. rimps both steel and stainless steel fittings For use with 25, 26, 43, 70, 71, 73, 76, 77, 78, 79, 81, S6 and HY fittings imensions: 31 wide, 24 deep, 77 high Weight: 842 lbs (Head is 558 lbs and base is 284 lbs) Rating: 125 ton 5,000 psi maximum Full ycle Time: 30 seconds without adapter bowl 20 seconds with adapter bowl Hydraulic oil: nerpac oil Part Number Individual escription Part Number Ä Ä Ä Ä Parkrimp 2 crimper head assembly Ä Ä Parkrimp 2 stand assembly with 230/460 volt, 3 phase, 50/60 83-S40 Hz power unit (wired for 230 volt) Ä Ä Parkrimp 2 stand assemlby with 230 volt, 1 phase, 50/60 83-S20 Hz power unit Ä Ä Ä Ä dapter bowl 83-O Ä Ä Ä Ä Spacer ring 83-R02 Ä Ä Ä Ä Spacer Plate 83-R02H Ä Ä ie Kit Includes 43 dies in sizes 1/4, 3/8, 1/2, 3/4, 1, 1-1/4 dies and 70/71 dies in sizes 3/8, 1/2, 3/4, 1, 1-1/4, 1-1/2, 2 ONLY 83-K Note: For crimp instructions, see pages -16 and -17. Hose assemblies must be inspected for cleanliness and free of all foreign particles. Parker Hannifin will not accept responsibility for the operation of, or provide warranty coverage for, a crimper that is operated by a power unit other than equipment supplied by Parker Hannifin for the express purpose of operating the crimper. -12 Hose Products ivision

13 atalog 4400 US Parkrimp 2 rimp Information Fitting Hose Products ivision Lakeland lvd HOS -4 R -5 PUR -6 YL -8 LU -10 ORG Parkrimp 2 Hose ie Selection hart GRN LK WHT R ie Part Number ST/T ST/T T ST/T 472LT ST/T 387/387ST/T (-4 THRU -16 ONLY) 487/487ST/T (-4 THRU -12 ONLY) -32 GRN H H H H L12 83-L16 83-L20 83-L24 83-L U12 83-U S24 83-S W LT /387ST/T (-20 ONLY) 487/487ST/T (-16 ONLY) 722/722ST/T/LT (-6 THRU -20 ONLY) ie Part Number F42 (-8 Only) 71 ie Part Number ST 772T LT 772ST 721T /722ST/T/LT (-24 N -32 ONLY) ie Part Number ie Part Number ie Part Number 787/787T 797/797T 387/387ST/T (-20, -24, -32 ONLY) 487/487ST/T (-20, -24, -32 ONLY) 80-S08 80-S10 80-S12 83-S16 83-S SIZ -32 IS FOR STL FITTINGS ONLY 78/S6 ie Part Number P T 782ST T F42 83-L16 83-L20 83-L24 83-L L12 83-L16 83-L20 83-L S6 Fittings are used on P35-32 Hose Only ie Part Number 791T 792LT 83-L12 792ST ie Part Number 80-Y06 80-Y ie Part Number V12 80-V16 80-V20 83-V24 83-V FR SS25UL SS23G 81 ie Part Number HT 881 ie Part Number 80-H H H H H H1365 X ie Part Number 80-H H H H H H H1880 XX H H H H H H HY ie Part Number 611HT aution: Read the operations and technical manual before attempting to operate this machine. o not operate this machine without guard in place. Keep hands clear of moving parts when operating machine. 83-R12 Split ie ring is used for all crimping operations 80-xxx/83-xxx small dies and 83-O adapter bowl used on sizes -4 thru -20 Note: Stainless steel crimp diamters are greater than table listings with the exception of HY series which are greater than table listings. o not use lubricant to assemble spiral hose and fittings. 83-R02 Spacer Ring used with adapter bowl when called out above 83-xxx Large dies used on sizes -16 thru -32 For a new ecal, contact Parker at: PRKR or print your own at ecal Part Number: 83-RIMPL R02H Spacer Plate used when called out above RV. Hose Products ivision

14 atalog 4400 US Portable Pumps Hand Pump Part No. 82-0HP Hand Pump Part No. 85-0HP (for use with the Minikrimp, Karrykrimp and Karrykrimp 2) ase of operation hand pump delivers 10,000 psi Length: 23 Width: 4 Height: 5 Port Size: 3/8 NPTF Weight: 9 lbs Hydraulic Fluid: nerpac oil lectric Pump Part No. 82-0P (for use with the Minikrimp, Karrykrimp and Karrykrimp 2) ase of operation electric pump delivers 10,000 psi Length: 13 Width: 13 Height: 15 Port Size: 3/8 NPTF Weight: 31 lbs Hydraulic Fluid: nerpac oil 115 volt, 1 phase, 50/60 Hz, 9 amp ir/hydraulic Pump Part No. 82-0P (for use with the Minikrimp, Karrykrimp and Karrykrimp 2) ase of operation hand pump delivers 10,000 psi Length: 29 Width: 13 Height: 11 Port Size: 3/8 NPTF Weight: 61 lbs Hydraulic Fluid: nerpac oil lectric Pump Part No. 85-0P (for use with the Minikrimp, Karrykrimp and Karrykrimp 2) Heavy duty electric pump delivers 10,000 psi at a faster cycle time Length: 19 Width: 11 Height: 17 Port Size: 3/8 NPTF Weight: 59 lbs Hydraulic Fluid: nerpac oil 115 volt, 1 phase, 50/60 Hz, 20 amp Vehicle attery- Powered Pump Part No V (for use with the Minikrimp, Karrykrimp and Karrykrimp 2) Lightweight pump operates with psi shop air pressure and delivers 10,000 psi Length: 15 Width: 6 Height: 6 Intake Port Size: 1/4 NPTF Output Port Size: 3/8 NPTF Weight: 14 lbs Hydraulic Fluid: nerpac oil (for use with the Minikrimp, Karrykrimp and Karrykrimp 2) Ideal unit for Parker Mobile Hose Replacement Service, elivering 10,000 psi. Length: 12 Width: 8 Height: 19.5 Weight: 67 lbs Hydraulic Fluid: ISO-46 nerpac Warranty Statement nerpac products are warranted to be free of defects in materials and workmanship. ny product that does not conform to specification will be repaired or replaced at nerpac s expense, anywhere in the world; simple as that! This warranty does not cover ordinary wear and tear, abuse, misuse, alterations, or the use of improper fluids. etermination of the authenticity of a warranty claim will be made only by nerpac or its uthorized Service enters. -14 Hose Products ivision

15 atalog 4400 US rimpsource rimpsource is the industry's most complete resource for crimper technical information. It contains all of the crimp specifications approved for Parker's rubber, industrial and thermoplastic hose: rimp specs PFs of technical manuals for easy downloading Parts lists Troubleshooting advice PFs of crimper decals for immediate printing rimpsource provides easy access to all the specifications necessary to correctly fabricate a factory quality hose assembly. rimpsource Spec Page series of dropdown menus enables users to find what they need quickly and easily. hoose your crimper, and then select the hose, fittings and current specifications needed to make hose assemblies. You can also print a simple-to-follow data specification sheet or crimper decal. Print your own crimp decals whenever you need to rimpsource Home Page -15 Hose Products ivision

16 atalog 4400 US Parkrimp ssembly Instructions rimping using Minikrimp, Karrykrimp, Karrykrimp ench Mount, Karrykrimp 2 and Karrykrimp 2 ench Mount Parkrimp Fittings 25, 26, 43, 70, 71, 73, 76, 78, S6, 81, HY 1 Mark insertion depth and push on fitting 2 Insert unitized die train Mark the hose insertion depth and push hose into fitting until the mark on the hose is even with the end of the shell. Lubricate hose if necessary, however, O NOT lubricate if using spiral hose. See Hose Insertion epth table below. For 81 Shells with 88 Fittings Place shell onto end of hose and make sure the end of the shell lines up with the Insertion epth mark. Push hose onto the 88 fitting until the shell bottoms against the fitting s stop ring or hex. Lubricate hose if necessary. olor-oded Unitized ie-train Pull pin at the top of pusher to swing it back. Place unitized die-train into base plate. See decal on crimper for proper die set. Note: Parkrimp 1 does not have a pin at the top of the pusher. Important: Lubricate the crimper s die bowl using a premium quality lithiumbase grease. 3 Position the fitting 4 Place die ring and crimp Parkrimp Position the hose and fitting in dies from below. Rest bottom of coupling on die step using the PRKLIGN feature. 5 Measure crimp diameter Standard Parkrimp rimp iameter 26 Measure crimp diameter on the flat surfaces of the crimped shell, referenced in the illustration to the left. Reference decal on crimper for crimp diameters. Never use hose assemblies with incorrect crimp diameters. Important: Hose assemblies must be inspected for cleanliness and free of all foreign particles. Place correct die ring on top of the dies. See decal on crimper for proper die ring. Position pusher by replacing the pin and operate pump until the die ring bottoms out. Release pressure within the pump remove finished assembly. Note: Minikrimp, Karrykrimp & Karrykrimp 2 have several types of power sources, all of which are separate units from the crimping machine. Hose insertion depths Fitting Fitting Size S HY inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm -4 13/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /16 43 For specific information on crimping, visit rimpsource TM online at Hose Products ivision

17 atalog 4400 US rimping using Superkrimp and Parkrimp 2 Parkrimp Fittings 25, 26, 43, 70, 71, 73, 76, 78, S6, 81, HY 1 2b Mark insertion depth and push on fitting Mark the hose insertion depth and push hose into fitting until the mark on the hose is even with the end of the shell. Lubricate hose if necessary, however, O NOT lubricate if using spiral hose. See Hose Insertion epth table on previous page. If using small unitized dies For 81 Shells with 88 Fittings Place 81 Shell onto end of hose and make sure the end of the shell lines up with the Insertion epth mark. Push hose onto the 88 fitting until the shell bottoms against the fitting s stop ring or hex. Lubricate hose if necessary. 2a Parkrimp ssembly Instructions If using large two-piece dies Insert the proper die set into the die bowl. (The die sets are in two halves of four dies each. Place one half in the back and one half in the front to accommodate bent tube fittings.) Reference decal on crimper for proper tool selection. 3 Place spacer ring Slide Pin 4 With the pusher in the full up position, lift the back half of the split die ring. Lock it in the up position by pushing the slide pin in. (The slide pin is located inside the pusher at the back.) Position the split die ring Lubricate die bowl using a premium quality lithiumbase grease. arefully insert the adapter bowl, 83-O, into the base bowl. The adapter bowl must be tilted toward the back of the crimper during insertion. olor-oded Unitized ie-train Lubricate die bowl using a premium quality lithium-base grease. Place unitized dietrain into the adapter bowl. Select die and die ring by hose size and type. See decal on crimper for proper die set. Note: ie sets have color-coded cavities indicating size and have the fitting series and dash size stamped on the top. 5 Position the fitting If required, place spacer ring on locating step of adapter bowl. Reference decal on crimper for tool selection. Parkrimp Slide Pin 6 Lower the back half of the split die ring onto the dies by pulling the slide pin forward. rimp hose Insert the front half of the split die ring aligning the pins in the back half with the hole in the front half. Turn on the pump by pressing the ON switch. Pull the valve handle forward to bring the pusher down for crimping. When the split die ring contacts the base plate, the crimp is complete. Push the valve handle back to lift the pusher, open the dies, and release the finished assembly. Note: You do not have to remove any tooling to insert or remove straight fittings. The front half of the split die ring and the front die train must be removed to insert and remove bent tube fittings. Position the hose and fitting in dies from below. Rest bottom of coupling on die step using the PRKLIGN feature. 7 Measure crimp diameter Measure crimp diameter on the flat surfaces of the crimped shell, referenced in the illustration to the right. Reference decal on crimper for crimp diameters. Never use hose assemblies with incorrect crimp diameters. Standard Parkrimp rimp iameter 26 Important: Hose assemblies must be inspected for cleanliness and free of all foreign particles. -17 Hose Products ivision

18 atalog 4400 US Twin-Tough Instructions Set-up: Position the bonded rubber hose so that it lies flat on a work surface without tendency to twist or turn. Measure hose tear back length: Measure and mark the length that the hoses are to be separated. minimum of 12 inches is required for crimping the hose ends. 24 inch tear back is recommended for use with hydraulic tools..) Using a sharp blade, pierce the center of the valley (web) formed by the hoses..) To start the cut, place the blade in the center of that valley (web) drawing the knife with constant pressure. -18 Hose Products ivision

19 atalog 4400 US Twin-Tough Instructions Measure Separation: It is suggested that the separation length be at least 12 inches, so the crimping operation can be accomplished without risk of kinking the hoses. Stopping Separation: Parker recommends installing a heat shrink sleeve of at least 2 inches in length at the termination of the separated hose to provide protection against tearing of the valley (web) or hose covers. This heat shrink sleeve should be placed on the hose assembly prior to the crimping of the hose fittings. Once you have your heat shrink sleeve in place, use a heat gun to shrink the sleeve in place. rimping Fittings: ll of your crimping information can be found on rimpsource ( -19 Hose Products ivision

20 atalog 4400 US onversion Kits Hydraulic Press Kit Part No. 8P-001 For use with 26, 43, 81 and HY Fitting ONLY Required Height from Press ase to Press Ram: 10 inches Required Width of owl iameter: 5 inches owl Rating: 30 tons force maximum Minimum Required Press apacity: Hose Size 1/4 to 1/2 needs a 20 ton press Hose size 5/8 to 1-1/4 needs a 30 ton press Standard Part Number Individual 8P-001 escription Part Number Ä owl ssembly 8P-030 Ä Pusher 8P-00P Ä Silver ie Ring 81-R01 Ä lack ie Ring 81-R02 Ä 43 dies in 1/4, 3/8, 1/2, 3/4 and 1 80-xx Weatherhead onversion Kit Part No. 8W-001 For use with 26, 43, 81 and HY Fitting ONLY onvert Weatherhead T-400 crimper to utilize Parker Parkrimp No-Skive fittings. Standard Part Number Individual 8W-001 escription Part Number Ä owl ssembly 8P-030 Ä Pusher 8W-00P Ä Silver ie Ring 81-R01 Ä lack ie Ring 81-R02 Ä 43 ies in 1/4, 3/8, 1/2 and 3/4 80-xx Gates onversion Kit Part No. 8G-002 For use with 26, 43, 81 and HY Fitting ONLY onvert Gates 701, 703 and 707 bottom loading crimpers to utilize Parker Parkrimp No-Skive fittings. Standard Part Number Individual 8G-002 escription Part Number Ä owl ssembly 8P-030 Ä Silver ie Ring 81-R01 Ä lack ie Ring 81-R02 Ä 43 ies in 1/4, 3/8, 1/2, 3/4 and 1 80-xx Notes: For additional information and operating instructions, visit the Parker Hose Products ivision website at. For crimping instructions, see pages -16 and -17. Hose assemblies must be inspected for cleanliness and free of all foreign particles. -20 Hose Products ivision

21 atalog 4400 US ut-off Machines Hose ut-off Machine - Karrykut Part No Hose ut-off Machine Part No. 332T-115V Portable saw for cutting on the job Unique clamp system spreads hose as it cuts to prevent blade binding uts multi-braided wire reinforced hose including 4 spiral construction up to 1-1/4 I.. imensions: 16 wide x 12 long x 19 high Shipping Weight: 58 lbs. Standard Part Number Individual escription Part Number Ä Power saw with 115volt (13 amp) universal motor Ä Universal clamp attachment (can be used with any portable power saw unit having a 5/8 arbor, 7 blade capacity) Ä utting blade (7 with 5/8 arbor size) Hose ut-off Machine Part No. TH3-51 Standard 14 scalloped blade Front plate with useable pins easily holds in place for a straight cut lear face shield uts 1 & 2 wire braid through 2 I.., 4-wire spiral through 2 I.., and 6-wire spiral through 1 I HP/115 volts 20 amp 1PH 50/60 cycle motor (a 20 amp dedicated circuit is recommended) imensions /2 wide x 13 long x 25-1/2 high Shipping weight - 67 lbs. lade size - 14 x x 1 Saw Part Number: TH3-51 Optional : Scalloped utting lade (TH3-50-1) Smooth evel utting lade (TH3-50-2) For quick, easy cutting of spiral reinforced hose up to 1-1/4 I.. Moving parts shielded by guards imensions: 13 wide x 26 long x 22 high Shipping Weight: 71 lbs. Standard Part Number Individual 332T-115V escription Part Number Ä Hose ut-off Machine with 1-1/2 HP, 3450 RPM, 115/230V single phase electric motor wired for 115V Ä Scallop utting lade (8 with 5/8 arbor size) Optional Smooth utting lade (580661) Hose ut-off Machine Part No. 239 and 339 esigned for heavy duty use uts multi-braided wire reinforced hose including 6 spiral construction up to 2 I.. imensions: 22 wide x 42 long x 24 high Shipping Weight: 115 lbs. Standard Part Number Individual escription Part Number Ä Hose ut-off Machine with 230V single phase motor Ä Hose ut-off Machine with 3 HP motor 230V, 3 phase, 60 cycle Ä Ä Scallop utting lade (10 with 3/4 arbor size) Optional Smooth utting lade (15960) -21 Hose Products ivision

22 atalog 4400 US Ultra lean Hose leaning Kit Ultra lean Hose leaning Kit conomy Hose leaning Kit Part No. TH6-10-HL-9-2 Part No. TH6-10-L-7 apable of cleaning 1/4 through 2 hose, tube or pipe The launcher is supplied with a Full-Flow Quick Release oupling and unique 360 Rotary Plug for proper air flow and non-fatigue operator use Unique Safety Release ar that locks the faceplate into a closed position for firing Ultra lean projectiles ir Requirements: 80 PSI (5.5 ar) minimum to 110 PSI (7.5 ar) maximum 1/2 I.. air hose 5 micron filter and regulator with gauge are strongly suggested conomy Kit apable of cleaning 1/4 through 1-1/4 hose, tube or pipe Has a quarter-turn locking ring for easy nozzle change and projectile loading The launcher is constructed of durable brass and aluminum internals, strong plastic handle, and anodized aluminum firing head and locking ring. Ideal for mobile and job site applications because of its size and portability ir Requirements: 80 PSI (5.5 ar) minimum to 110 PSI (7.5 ar) maximum 1/2 I.. air hose 5 micron filter and regulator with gauge are strongly suggested Optional & ccessories: range of projectiles are available enabling the Ultra lean System to be used on different sizes and types of hose, as well as coupling configurations dditional nozzles for JI, ode 61 and ode 62 flanges, and ORFS are also available if required -22 Hose Products ivision

23 atalog 4400 US Ultra lean Hose leaning Kit Ultra lean Hose leaning Kit Sizing hart and Part Numbers HOS ONLY Projectile Hose Size Nozzle Part Number Part Number 3/16 TH6-10-H06 TH6-10-P06 1/4 TH6-10-H06 TH6-10-P10 3/8 TH6-10-H10 TH6-10-P14 1/2 TH6-10-H13 TH6-10-P18 5/8 TH6-10-H16 TH6-10-P22 3/4 TH6-10-H19 TH6-10-P26 1 TH6-10-H25 TH6-10-P33 1-1/4 TH6-10-H32 TH6-10-P40 1-1/2 TH6-10-H38 TH6-10-P50 2 TH6-10-H50 TH6-10-P60 HOS SSY W/FJI Projectile FJI Size Nozzle Part Number Part Number 1/4 TH6-10-J06 TH6-10-P06 3/8 TH6-10-J10 TH6-10-P12 1/2 TH6-10-J13 TH6-10-P16 5/8 TH6-10-J16 TH6-10-P22 3/4 TH6-10-J19 TH6-10-P26 1 TH6-10-J25 TH6-10-P33 1-1/4 TH6-10-J32 TH6-10-P40 1-1/2 TH6-10-J38 TH6-10-P50 2 TH6-10-J50 TH6-10-P60 HOS SSY W/FFORX Projectile FFORX Size Nozzle Part Number Part Number 1/4 TH6-10-4FFORX TH6-10-P06 3/8 TH6-10-H06 TH6-10-P12 1/2 TH6-10-H10 TH6-10-P16 5/8 TH6-10-H13 TH6-10-P22 3/4 TH6-10-H16 TH6-10-P26 1 TH6-10-H19 TH6-10-P33 1-1/4 TH6-10-H25 TH6-10-P40 HOS SSY W/ode 61 & 62 Flanges Projectile Flange Size Nozzle Part Number Part Number 1/2 TH6-10-H10 TH6-10-P16 3/4 TH6-10-H16 TH6-10-P26 1 TH6-10-H19 TH6-10-P33 1-1/4 TH6-10-H25 TH6-10-P40 1-1/2 TH6-10-H32 TH6-10-P50 2 TH6-10-H38 TH6-10-P60 PROJTIL QUNTITIS Parker Part Number escription Qty. TH6-10-P06 PROJTIL 3/ PR G TH6-10-P10 PROJTIL 1/4 100 PR G TH6-10-P12 PROJTIL 1/4 N 5/ PR G TH6-10-P14 PROJTIL 3/8 100 PR G TH6-10-P16 PROJTIL 3/8 100 PR G TH6-10-P18 PROJTIL 1/2 100 PR G TH6-10-P22 PROJTIL 5/8 50 PR G TH6-10-P26 PROJTIL 3/4 50 PR G TH6-10-P33 PROJTIL 1 40 PR G TH6-10-P40 PROJTIL 1-1/4 30 PR G TH6-10-P50 PROJTIL 1-1/2 20 PR G TH6-10-P60 PROJTIL 2 15 PR G -23 Hose Products ivision

24 atalog 4400 US ccessories Hose ut-off Tool - Handykut Part No Push-Lok ut-off & ssembly Tool Part No Portable tool for efficient cutting of hose an be positioned onto a flat surface by clamps or by locking it in a vise, properly align the hose in a radius and cut it with a hacksaw ombined hose cutter and toggle action press that cuts and assembles Parker Push-Lok in sizes 1/4 through 3/4 I.. imensions: 6 wide x 18 long x 6 high Shipping Weight: 10 lbs. imensions: 16 long Shipping Weight: 4 lbs. Hose Insertion epth locks Part No. TH9-1-XXX Hose ut-off Tool Part No. TH11-1 For quick easy marking of hose insertion depth nsures accuracy and increased productivity vailable locks Part Number escription TH through -10 TH through -32 TH through -10 TH through -32 TH through -20 TH through -32 TH through -32 TH through -16 TH through -32 TH through -24 TH9-1-HY HY -4 through -16 esigned for quick, easy cutting of textile reinforced hose. Squarely cuts Push-Lok hose in sizes 1/4 through 3/4 I.. imensions: 8 long Shipping Weight: 0.3 lbs. -24 Hose Products ivision

25 atalog 4400 US ccessories Hozembler Part No V ie Storage Racks Part No. 80-0R and 83-0R Power machine to facilitate the attachment of field attachable fittings Handles all hose and fittings up to 4 spiral wire, in sizes 3/16 through 2 I.., including bent tube elbows omes with vise, all adapters, foot switch and safety guard with 115V, 30 amp, universal motor Modular die rack designed to hold small and large Parkrimp dies an be bolted together to a work bench horizontally or vertically Shipping Weight: 141 lbs. Optional Parts Mounting stand (662451) Standard Part Number 80-0R 83-0R escription Ä Ä Storage of three sets of small dies Storage of two sets of large dies Swivel ie Rack Part No. 80-SR-XXXX Fitting Push-On Stand Part No. TH2-7 Holds up to 30 Parkrimp dies of any size Powder-coated, heavy-duty steel construction onsists of a base unit and up to five circular holders Floor or bench mounted Standard Part Number 80-SR-SM 80-SR-LG 80-SR-S escription Swivel ie Rack and Small ie Holder Swivel ie Rack and Large ie Holder Swivel ie Rack ase Quickly and easily pushes fittings onto hose oosts productivity and quality liminates the need of rubber mallets and oils to get fittings onto the end of the hose for crimping Standard with straight tooling required for sizes 1/4 through 2 for all crimped fittings, 82 Push-Lok and 88 field attachable fittings Requires a minimum of 80 psi Shipping Weight: 200 lbs. Optional Tooling lbow Pusher Set (TH2-7-LS) -25 Hose Products ivision

26 atalog 4400 US ccessories Mandrel Tool Kit - 22 Part No Mandrel Tool Kit - 23 Part No and 2726 For assembly of Parker 22 field attachable fittings One of each part listed below is included in the kit For assembly of Parker 23 field attachable fittings Part No is for JI 37 flared fittings Part No is for S 45 and PTT 30 flared fittings Standard Hose I.. ash Size S (JI) 37 S 45 3/16-4 Ä Ä 1/4-5 Ä Ä 5/16-6 Ä Ä 13/32-8 Ä Ä 1/2-10 Ä Ä 5/8-12 Ä Ä Standard Hose I.. ash Size /16-4 Ä Ä 1/4-5 Ä Ä 5/16-6 Ä Ä 13/32-8 Ä Ä 1/2-10 Ä Ä 5/8-12 Ä Ä 7/8-16 Ä Ä Mandrels - 25 (For 271 Transportation Hose) Part No. TH2-7M25-6 and TH2-7M25-8 ssembly Tools - 22 Part No For assembly of Parker 22 field attachable fittings One of each part listed below is included in the kit Standard Hose I.. ash Size S (JI) 37 S 45 7/8-16 Ä Ä 1-1/8-20 Ä Ä 1-3/8-24 Ä Ä 1-13/16-32 Ä -26 Hose Products ivision

27 atalog 4400 US ccessories Hose Perforator Part No Hose Oil Part No. Hose Oil Small hand tool to prick minute holes in the rubber cover To be used in gaseous applications where the pressure exceeds 250 psi riven into the cover every few inches of length either striking the hose or by a rolling action over the hose cover Not generally necessary to perforate the hose on all sides Shipping Weight: 2 lbs. Reduces torque and eliminates waste lubrication Use hose oil with the recommended hose assembly instructions ccrolube Part No. ccrolube High efficiency lubricant used for stainless steel field attachable fittings ontains PTF to reduce the wear between metal surfaces, protects against corrosion and ultimately eliminates galling Small rimper Hood Part No. 82-VR Large rimper Hood Part No. 83-VR Water repellant UV protected Perfect for indoor and outdoor applications Fits Karrykrimp, Parkrimp Karrykrimp2, Minikrimp Water repellant UV protected Perfect for indoor and outdoor applications Fits PHastkrimp, Superkrimp Parkrimp2-27 Hose Products ivision