Touring Caravan OWNERS HANDBOOK. Issue 1

Transcription

1 Touring Caravan OWNERS HANDBOOK Issue 1

2

3 CONTENTS WELCOME AND INTRODUCTION Model Year Compass Group Technical Approvals GENERAL SAFETY Please read before using your new caravan Ventilation High-Level Ventilation Low-Level Ventilation Ventilation in Separate Bedrooms Gas Dispersal Holes Petrol/Diesel Fumes Fire Safety Fire Extinguishers In Case Of Fire Fire Retardant Foams PREPARING FOR THE ROAD Caravan Towing Vehicle Weight Ratio Nose Weight Indicator Jockey Wheel Loading Internal Loading & Checks External Loading & Checks Pre-Tow Checklist & Hitch-Up Winterhoff Stabiliser - Hitch Head Operation3-2 Activating the stabiliser Checking the stabiliser Uncoupling Use of Your Caravans Breakaway Cable Correct Procedure For Use Where a Designated Attachment Point Is Provided On The Tow Bar Where No Designated Attachment Point Is Provided On The Tow Bar Other Means of Attachment When The Breakaway Cable Is Attached Check To Ensure Before Setting Off Handbrake Cables TOWING AND DRIVING Reversing Speed Limits Setting Off Caravan Handling ARRIVING ON SITE Check Site Regulations Selecting a Pitch Side-To-Side Levelling Leveller Jack Ramp Front & Back Levelling Parking on a Reverse-Sloping Site or Steep Hill GETTING STARTED Electricity Power Supply Charger v Systems: Generator/Charger Electricity Mains Supply Connecting To Mains Supply On Arrival at Site Disconnecting Mains Supply When Leaving Site Overseas Electrical Connection Gas Supply Connection Changing a Gas Cylinder Gas Regulator High Pressure Gas Hoses Water System How to Use Your Aquasource Connection to your water inlet Draining Down Your Water System GAS SAFETY ADVICE Facts about LPG Awning Spaces, LPG and Appliance Exhaust LPG Gas System Gas Barbecue Point ELECTRICAL SYSTEM v Power Supply Battery Installation Battery Maintenance Generators / Charger v Power Supply Mains Unit Resetting the RCD Automatic Charging System Maximum Bulb Ratings for Internal Lights Connecting a Solar Panel and/or Satellite Dish Solar Panel Connection Satellite TC Connection V Fuses - All Models HOW TO USE YOUR CARAVAN S EQUIPMENT Electrical Control Panel Omega Cooking equipment Gas Hob Gas Grill Gas Oven CONTENTS-1

4 CONTENTS Refrigerator Model Thetford N112 LCD Operating instructions Smart Energy Selection (SES) Powering with electricity Selecting electrical power manually Powering with gas Switching off the refrigerator Securing products for driving Door locking mechanism Troubleshooting Maintenance Water heater operation Gas operation V Operation Space Heater Operation Gas Operation V Operation Fan Operation Microwave Battery Charger Smoke Detector Thetford Cassette C-200 CWE Toilet Introduction Features: Preparing for use Emptying the waste holding tank Winterising/Storage Cold weather use High Altitude and hot weather use Cleaning and maintenance Rooflights The Omivent (12v) Rooflight Toilet unit malfunctions The Heki 2 Rooflight Mini Heki Rooflight Windows Polyplastic Window Opening Blinds & Flyscreens Flyscreens Door Flyscreen Taps Exterior Door Retainers Gas Locker Door Internal Doors Magnetic Catches Bed Make-up L-Shape Lounge Double Bed Bunk Beds Removable Drawer Locker TV Aerial VHF Television Reception (Overseas only) Entertainment System Radio/DVD LCD TV BPW Nose Weight Indicator Jockey Wheel Explorer Protect - Autowatch Alarm System 9-23 BPW Intelligent Drive Control (idc) System 9-24 SECURITY Caravan Theft Anti-Wind Corner Steadies CRIS - The Caravan Registration and Identification Scheme - VIN Window Etching & Chassis Marking Electronic Tagging CARE OF YOUR CARAVAN Exterior Cleaning Glass Fibre Reinforced Plastic (GRP) Acrylic Windows Care Instructions for Seitz Windows Care Instructions for Seitz Rooflights Window Blinds & Flyscreens Winterisation/Storage ABS - A Frame Cover, Wheel Spats & Panels 11-2 Interior Walls Furniture Cooking Equipment Carpets, Upholstery and Curtains Shower Trays, Shower Room and Wash Basin Fittings Cleaning of all Taps Water Containers Water Systems - Sterilization Truma Space Heater Thetford Toilet Chassis Mounted Spare Wheel Carrier Tyres Pressures Tyre Wear and Damage Changing a Wheel Jacking Lubrication Maintenance of your BPW Chassis Procurement of Spare Parts STORAGE Long Term & Winter Storage Caravan Covers Power Drain WARRANTY Year Manufacturer s Warranty Parts Covered By This Warranty for Years CONTENTS-2

5 CONTENTS Specific Exclusions for Years 2 & Conditions Attached to the Warranty: CODE OF PRACTICE - WATER INGRESS The Code Conditions Attached To the Code Customer Obligation - Servicing Mains Electrics Spare Parts Remedial Work CARAVAN CONSTRUCTION - MAIN COMPONENTS BPW Chassis Braking System Body Shell Windows Insulation Front Panel and Gas Bottle Locker Lid Awning Channel Additional Fixings to Your Caravan Shell Omega ELECTRICAL DRAWINGS Pin Plug Wiring Diagram Wiring Diagram - Omega Road Lights - Omega TECHNICAL SPECIFICATIONS Compass Omega GENERAL QUESTIONS GLOSSARY SERVICE DOCUMENTS INDEX CONTENTS-3

6 CONTENTS CONTENTS-4

7 INTRODUCTION WELCOME AND INTRODUCTION Congratulations on choosing a Compass Touring Caravan. This Owner s Handbook has been prepared for your guidance to help you derive the greatest amount of pleasure from the use of your caravan and your leisure time. We strongly recommend that you read this guide thoroughly so that you are fully aware of all the caravan s features, equipment and systems. Additional information and detailed appliance instruction manuals are also contained in your Owner s Information Pack. Your new Compass caravan has been designed as a recreational vehicle and is intended for recreational use only. It is not intended for business use or for permanent habitation. Compass accepts no liability if the caravan is used for any purpose other than recreational/holiday use. Your caravan has been designed for towing behind a normal motor car. Additional care should be exercised when towing with a 4x4 because of the off-road nature of the suspension. Owners should not tow their touring caravans with commercial vehicles (including light and heavy goods vehicles). When selecting a towing vehicle it is recommended that you consult the Caravan Towing Code, which is also included in your Owner s Information Pack. By following the instructions provided in this handbook and maintaining your caravan in a first class roadworthy condition, you are sure to have many years of carefree use. To ensure the very best quality and reliability all touring caravan designs and new developments are rigorously tested. Therefore Compass will accept no liability or uphold the warranty if the caravan is altered or modified in such a way that would adversely affect the reliability. Please Note: It is a condition of your warranty that the caravan must have an annual service done by an Approved Retailer or Service Centre, and a record is kept. Pages are provided in the back of this guide, for your assistance. Approved Retailers or Service Centres will be able to supply any replacement parts for your caravan, should the need arise, and in most cases any accessories you may require. Please note: It is not possible to purchase replacement parts direct from Compass. Changing market and supply situations may prevent us from maintaining the exact specification details in this guide and we therefore reserve the right to alter specifications as materials and conditions demand. Enjoy your new caravan Model Year All Touring caravans manufactured by Compass are designated by their model year. The 2009 model year runs from 1st September 2008 to 31st August Compass Group Technical Approvals In order to ensure your new Caravan is safe to use Compass are members of and have been inspected by the following bodies. National Caravan Council (NCC) who operated a certification scheme to ensure compliance with the European safety standards for caravans. National Inspection Council for Electrical Installation and Contracting (NICEIC) who carry out an annual inspection of Compass electrical installations within caravans. Confederation of Gas Installers (CORGI) who carries out annual inspection to ensure that the gas installation installed by Compass fully comply with all relevant regulations and standards. Compass has also obtained ISO9001:2000 accreditation and this is audited by SGS UK Limited 1-1

8 INTRODUCTION 1-2

9 GENERAL SAFETY GENERAL SAFETY Please read before using your new caravan. In order for you to get the most out of your new Compass caravan it is necessary for you to be aware of the following: (i) Do not obstruct ventilators and clean them regularly, it is advisable to clean and check all the ventilators annually for blockages and where necessary rectify any blockages found. (ii) Inspect the high pressure flexible gas hose (available from your retailer) regularly for deterioration and renew as necessary, with approved type, in any case no later than the expiry date stated on the hose. (iii) Turn off all gas appliances and turn off the gas supply before towing your caravan. (iv) Your caravan is fitted with a gas barbecue point which is not designed to allow gas flow into your caravan and should never be used for this purpose. (v) Never use portable cooking or heating equipment inside your caravan. Do not use your fitted cooking equipment as heating at any time. (vi) Never allow modification to your gas or electrical system unless qualified persons carry them out. All modification to the gas system should be carried out by a CORGI registered gas fitter. Any modifications carried out on the electrical system should be carried out by an electrician on the roll of the NICEIC or be a member of the ECA. (vii) In the interest of safety, replacement parts for an appliance shall conform to the appliance manufacturer s specifications and should be fitted by him or his authorised agent. (viii) It is recommended that you provide a dry powder fire extinguisher complying with ISO 7165 of at least 1KG capacity by the exit door and a fire blanket next to the cooker. Ensure you read the advice to occupier label fitted to your caravan usually found on the inside of the wardrobe door. (ix) Never exceed your caravans Maximum Technical Permissible Laden Mass. (see Caravan Towing Vehicle Weight Ratio) (x) The laden nose weight for your caravan should not exceed the lower of the following: Towing vehicles maximum nose weight Tow bar maximum nose weight The caravan s maximum nose weight which is 100kgs (xi) Ensure heavy and large items are secured before towing your new caravan to reduce the risk of damage being caused while the caravan is in motion. (xii) When your caravan is connected to your towing vehicle it should be level or slightly nose down. An excessive nose down attitude or a nose up attitude could lead to instability when towing. (xiii) When your caravan is loaded to its MTPLM and the weight distributed in accordance with the towing code, your caravan is designed to be towed at a maximum speed of 130kmh/80mph. However, your attention is drawn to the fact that in the UK the maximum speed allowed for towing a caravan is 100kmh/ 60mph. (xiv) It is illegal to tow your caravan whilst it is occupied. (xv) If your caravan is fitted with a lift up bunk it is designed for a maximum weight of 11 stone and is not suitable for children under 3 years old without supervision. (xvi) Do not leave children under 14 years of age unattended in your caravan. IMPORTANT Your attention is drawn to the notice affixed in the caravan s wardrobe advising on fire prevention, ventilation and what to do in case of fire. 2-1

10 GENERAL SAFETY VENTILATION All caravans manufactured by Compass are ventilated at both high and low level in accordance with BSEN 721 Safety Ventilation. The fixed ventilation points fitted in your caravan must not be blocked under any circumstances as your safety may depend upon them. It is advisable that the fixed ventilation points are checked and cleaned (where necessary) on a regular basis. High-Level Ventilation This is always provided by fixed ventilation within the fitted roof skylight. All roof skylights fitted by Compass provide fixed free area ventilation. These roof skylights should be cleaned annually by use of a small brush to remove any dust that may have accumulated around the mesh fitted. On some roof skylights the mesh can be easily removed to aid cleaning. On fan-assisted roof skylights it is essential that the fan is switched off prior to cleaning. Low-Level Ventilation Low-level ventilation is provided under the front chest of drawers, except in an L shape layout, where it can be found either in the nearside or offside bed box. The exact position can be identified via the white or black plastic cover used to prevent the ventilation from being obstructed. In order to clean the ventilator, remove the cover by undoing the two screws and clean using a small brush. It is essential that the cover is replaced once cleaning is complete. Ventilation in Separate Bedrooms In caravans with separated sleeping areas, separate ventilation is required and is provided via a roof skylight at high level and a ventilator at low level within a bed box. Gas Dispersal Holes All appliances and gas unions have a gas dispersal hole nearby. It is essential that these are not blocked or made ineffective. Petrol/Diesel Fumes The fitting of a tail pipe to your exhaust will reduce the possibility of fumes entering your caravan through the front fixed ventilation points. FIRE SAFETY Fire Extinguishers It is recommended that a 1 kg minimum capacity dry powder fire extinguisher be carried inside your caravan at all times. A fat pan fire must not have an extinguisher aimed at it, but must be smothered with a fire blanket. In Case Of Fire (i) Get everyone out of the caravan as quickly as possible using whichever exit is quickest including windows. Do not stop to collect any personal items. (ii) Raise the alarm. Call the fire brigade. (iii) Turn off gas container valve if safe to do so. Fire Retardant Foams Under the requirements of the Consumer Protection Act 1987, the manufacturer has a responsibility to ensure that their product is as safe as possible. With this in mind all caravans are equipped with either Combustion Modified High Resilient (C.M.H.R.) foam cushions or sprung mattresses. These foams are very much safer from a fire point of view than those previously used. In addition all upholstery is made of fire retardant fabric. 2-2

11 PREPARING FOR THE ROAD PREPARING FOR THE ROAD Before venturing out on to the road with your touring caravan, it is important that you prepare correctly. CARAVAN TOWING VEHICLE WEIGHT RATIO This ratio has a major influence on stability. It is recommended that: (i) The laden nose weight for your caravan should not exceed the lower of the following: * Towing vehicles maximum nose weight, * Tow bar maximum nose weight * The caravan s maximum nose weight, which is 100kgs (ii) The actual laden weight of the caravan should always be kept as light as possible. The lighter it is whilst being towed on a road, the safer the outfit combination will be. (iii) The Caravan Club recommends a maximum caravan/towing vehicle weight ratio of 85% of the towing vehicle s kerb weight providing both are properly maintained, fully serviceable and the other recommendations in this Handbook are followed. (iv) Whilst you can legally tow at a higher weight ratio than 85% (subject to manufacturers towing limits and driving license restrictions) towing a heavier caravan will increase the risk of instability, especially at higher speeds. (v) The greater the actual laden weight of the caravan in relation to the kerb weight of the towing vehicle the more careful and experienced the driver needs to be and the lower the speed at which instability could occur. WARNING: It is strongly recommended the loaded weight of the caravan does not exceed the kerb weight of the towing vehicle. NOSE WEIGHT INDICATOR JOCKEY WHEEL The Jockey wheel nose weight indicator is fitted to all Compass caravans. This can be used to give guidance on the actual nose weight your caravan is applying to your car s tow ball. Please note that this should only be used as a guide. For information on how to use the nose weight indicator please go to the section on How To Use Your Caravan s Equipment. LOADING Always lower and secure the jockey wheel and the four corner steadies (with the brace provided) before entering the caravan. This will ensure that the caravan does not tip up when you are inside. Please Note: Corner steadies should not be used as a jacking device. Internal Loading & Checks When loading your caravan it is advisable to: (i) Distribute items evenly over the axle and as low as possible to optimize road holding and achieve the best possible braking effect. (ii) Do not overload on one side as this will cause the caravan to lean and affect the road holding and stability. (iii) Do not stow tins, bottles or heavy items in overhead lockers when towing. (iv) Loose articles should be stowed securely to avoid movement and possible damage. (v) Ensure that all lockers and cupboard doors are closed and secured. (vi) Secure all bunks (if appropriate). (vii) Store the main dining table in its transit position. (viii) Set the refrigerator for 12V operation if any fresh food is stored in it and ensure the door is locked. (ix) Fully close and lock all windows and rooflights. Never tow with windows on night setting. (x) Leave all curtains and blinds open to prevent damage in transit. If your caravan has a rear window this may aid visibility. External Loading & Checks (i) Gas cylinders should only be stored, correctly positioned, and secured in the gas bottle locker. The gas should be turned off. (ii) The leisure battery is stored and secured in the battery locker box, set into the tray provided and secured. 3-1

12 PREPARING FOR THE ROAD (iii) Any external connections (battery chargers, connecting cables etc), should be disconnected and stowed. (iv) Check that all exterior locker doors are secure and locked. (v) Secure and lock the main caravan entrance door. PRE-TOW CHECKLIST & HITCH-UP Having loaded the touring caravan and secured the lockers and main entrance door: (i) Check touring caravan wheel bolts are torque tightened to the required level (See Index - Changing a Wheel). (ii) Check tyre pressures (Refer to the Technical Specification section) and tyre condition for roadworthiness. (iii) Ensure the jockey wheel is down, in good contact with the ground, clamp tightly secured, and the caravan handbrake is fully on. (iv) Wind up the corner steadies. (v) Reverse the car close up to the caravan s hitch. It is advisable to seek assistance to guide you so that the car tow ball aligns with the caravan s hitch. (Use of the caravan handbrake is advised. Extreme caution should be taken if manoeuvring the caravan down hill or on wet, slippery surfaces). (vi) Make sure the jockey wheel height is sufficient for the hitch head to clear the towing vehicles tow ball. (v) Manoeuvre the hitch head over the tow ball and lower the jockey wheel using the winding handle, until the hitch head opening sits comfortably over the tow bar ball. WINTERHOFF STABILISER - HITCH HEAD OPERATION Coupling The opened ball coupling is placed over the tow ball of the towing vehicle. As the coupling load is applied to the tow ball the coupling will automatically close, this is indicated when the security lugs become parallel on the side of the housing. (Fig 3.1) Fig 3-1 Activating the stabiliser The operating handle will not operate until the automatic closing function has been engaged. The handle can now be fully pushed down. The hitch will remain coupled with the stabiliser deactivated to facilitate easier manoeuvring. Checking the stabiliser With the caravan coupled to your towing vehicle and the stabiliser activated, the condition of the friction linings can be checked. The wear indicator (as shown in Fig 3.2) is within the top of the operating handle. The bar graph is marked with (+) and (-) symbols with (+) indicating good condition of the pads and (-) indicating that the pads should be checked. Fig 3-2 Disengaging the stabiliser Lift up the operating handle with care to release the sprung loaded stabiliser function. 3-2

13 PREPARING FOR THE ROAD Uncoupling Fig 3-3 Before uncoupling disconnect the electrical connections and breakaway cable. Also check that it is safe to uncouple your caravan taking into account any gradients. With the stabiliser function disengaged, simultaneously pull back and lift the operating handle, this swings the securing lugs out of the locked position allowing the operating handle to be lifted into the fully open position. Before operating the jockey wheel, which will lift the caravan free of the tow ball, check that both caravan and towing vehicle handbrakes are applied! If the caravan is not to be used for any lengthy period of time we recommend the ball coupling is kept in the closed position. This can be done easily by pressing the safety ball into the ball space and slowly closing the operating lever. Please note: The WS3000 ball coupling can be locked in both the coupled and uncoupled condition with the ROBSTOP WS3000 hitch lock, however it is recommended that the Robstop is removed for towing. USE OF YOUR CARAVANS BREAKAWAY CABLE UK LAW requires that all caravans with brakes (e.g. caravans, horse boxes, car transporters etc), built on or after 1st October 1982, are fitted with a safety device to provide protection in the unlikely event of the separation of the main coupling while in motion. It s also a legal requirement to use the breakaway cable whenever it s provided. The purpose of the breakaway cable is to apply the caravan s brakes if it becomes separated from its towing vehicle. The cable assembly is designed to part, allowing the caravan to come to a halt away from the towing vehicle. Construction - Usually a thin steel cable, possibly plastic coated, and fitted with a means of attachment to connect to the towing vehicle. Operation - The cable should be able to pull tight to engage the caravan s brakes without any hindrance to its action, if the main coupling of the caravan separates from the towing vehicle. It should never become taut during normal use. Correct Procedure For Use (i) Check cable assembly for damage. If in doubt contact your Retailer or Service Centre. (ii) Make sure the cable runs as straight as possible, and goes through a cable guide underneath the caravan coupling. (iii) Determine whether or not you have a designated attachment point (a feature of the tow bar which has been identified by the tow bar supplier as being for the attachment of a breakaway cable). Where a Designated Attachment Point Is Provided On The Tow Bar (i) Pass the cable through attachment point and clip it back on itself (Fig 3-4, Step 1); or STEP 1 Fig

14 PREPARING FOR THE ROAD (ii) Attach the clip directly to the attachment point (Fig 3-5, Step 2). Note: this must be specifically permitted by the caravan manufacturer s guidance, as the clip may not be sufficiently strong. Where No Designated Attachment Point Is Provided On The Tow Bar (i) STEP 2 Fig 3-5 Fixed Ball - Loop the cable around the neck of the tow ball. If you fit the cable like this use a single loop only (Fig 3-6, Step 3). STEP 3 accessories e.g. a stabiliser, bumper shield, cycle carrier etc. (ii) That there must be sufficient slack in the cable to allow the towing vehicle and caravan to fully articulate without the cable ever becoming taut and applying the brakes. (iii) That it is not so slack that it can drag on the ground. Leave it too loose, and the cable may scrape along the ground, and be weakened so that it fails before doing its job! BEFORE SETTING OFF (i) Connect the 13 pin plug on the caravan A- frame to the towing vehicle. (ii) Check that all tail-lights, brake lights, road lights and indicators work correctly. (iii) Ensure that the correct vehicle license / registration plate is attached to the rear of the touring caravan. (iv) Using the jockey wheel lift the tow ball slightly to check hitch is locked onto the ball (v) Wind up the jockey wheel until the wheel supports locate into the cut out sections at the base of the winding section. (vi) Raise and secure the jockey wheel using the clamp. The jockey wheel should be parallel to the direction of travel at all times. (vii) Check condition of and secure the breakaway cable to the tow vehicle. Fig 3-6 (ii) Detachable Ball - You must contact the tow bar supplier for advice. Other Means of Attachment Alternatively, it may be possible to attach the cable assembly to a permanent part of the tow bar structure with the approval of the tow bar supplier, or to an accessory sold for the purposes of breakaway cable attachment. When The Breakaway Cable Is Attached Check To Ensure (i) That the cable cannot snag in use on the caravan hitch, jockey wheel or any 3-4

15 PREPARING FOR THE ROAD HANDBRAKE Your caravan is fitted with BPW running gear and handbrake. It is essential that prior to towing you ensure that your handbrake is in the fully off position. This can be confirmed by ensuring that the handbrake arm is resting on the blue stop fitted to the side of the A frame as shown in Fig 3-7 below. Fig 3-7 CABLES For peace of mind, you may wish to check the ability of the cables to be able to cope with towing the vehicle at extreme angles before setting off. To do so position the vehicle at alternate extreme angles and check that the cables do not pull too tight, are liable to stretch or become unplugged. No cables should be allowed to touch the ground as they will wear and become damaged and ineffective. Please Note: If having followed this advice, you feel you cannot achieve a satisfactory cable arrangement, consult your caravan or tow bar supplier or service agent. 3-5

16 PREPARING FOR THE ROAD 3-6

17 TOWING AND DRIVING TOWING AND DRIVING REVERSING It is advisable to have a second person available when reversing the caravan. Start practising by choosing a left-hand bend for ease. Reverse slowly; turning the wheel, initially the opposite way to the direction you want the caravan to go. Now the front of the caravan is nudged out and is moving the rear in the intended direction. Take care not to hit the van with the car! Midways through the manoeuvre, when the caravan is correctly angled, reduce speed to a crawl and gradually apply opposite lock. Make the car follow the caravan round then finally straighten up. Please Note: Proficiency at reversing can only be achieved with practice. SPEED LIMITS Normal road towing: 50mph Motorways (including dual carriageways): 60mph SETTING OFF (i) Let the clutch in smoothly on the towing vehicle. Allow more engine speed to produce the power to move the additional weight of the caravan. (ii) Avoid wear and tear on the clutch and transmission by taking extra care not to ride the clutch. (iii) Change gears smoothly. Try not to jerk the clutch. CARAVAN HANDLING (i) Allow for the caravan being wider than the car. Ensure you have a clear view to the rear. This may require the fitting of extended mirrors for towing your caravan. (ii) Do not bump the kerb with the caravan wheels. (iii) When passing other vehicles, allow more than the normal clearance for driving solo. (iv) Allow longer to obtain a fast enough speed to pass other vehicles. (v) Allow for the vehicle being twice its normal length. Do not suddenly swing out. (vi) Carry out all manoeuvres as smoothly as possible. (vii) Use the nearside wing mirror to check the caravan has clearly passed other road users when overtaking and changing lanes. (viii) Adverse weather conditions may affect the steering and braking characteristics of your caravan. Fig

18 TOWING AND DRIVING 4-2

19 ARRIVING ON SITE ARRIVING ON SITE CHECK SITE REGULATIONS On arrival at a site, you should always check the site regulations. This will help avoid any unnecessary conflict with site management and other site users. WARNING: Care has to be taken to prevent fouling when traversing ramps or other ground obstacles. SELECTING A PITCH Carefully select where you wish to place your caravan. The site should be as level as possible, preferably not under or near trees, well drained and away from possible boggy areas. Consider how you will move the caravan when it is time to leave the site. On sloping ground it is better to pitch facing downhill, especially during wet weather. SIDE-TO-SIDE LEVELLING A quick glance at your pitch should tell you if you are likely to need side to side levelling i.e. levelling across the axle. On uneven ground lateral levelling is accomplished by the use of a leveller jack or ramp and a spirit level placed across the caravan floor (not supplied). Leveller Jack Place the leveller jack, folded flat, in front of the wheel needed to be raised to level the axle. Tow the caravan onto the leveller jack and adjust the height until the spirit level shows that the caravan is laterally level. Ramp (i) Reverse onto your pitch about 30cm (12") further back than you wish to end up. (ii) Then place the levelling ramp in front of the wheel that needs to be raised. (iii) Place a spirit level parallel to the axle on the A-frame or just inside the caravan door. It helps to have two people at this point. One should drive the car very slowly forward moving the caravan wheel up the ramp, and the other should indicate when the spirit level bubble is in the middle. Whichever method you use, and once level: (i) Apply the caravan handbrake and chock the caravan wheel if necessary. (ii) Lower the jockey wheel to ground level before unhitching. (See index uncoupling) You should then park your car, usually next to the caravan furthest away from the door side. Please Note: On upward facing pitches when the hydraulically damped drawbar of the hitch becomes fully extended, it will be necessary to compress the drawbar slightly in order to achieve a clean unhitching. With the caravan brake on, reverse the towing vehicle about 2.54cm (1") to release hitch lock tension and using the jockey wheel adjustment, unhitch the caravan as previously described. FRONT & BACK LEVELLING This should be done only when the lateral levelling is complete. (i) Place the spirit level pointing front to back just inside the caravan door or on the A frame. (ii) Then raise or lower the jockey wheel until the caravan is horizontally level. Please Note: If there is a significant front to back slope, you may need to place a block under the jockey wheel. (iii) Next, wind down the corner steadies onto load spreaders (blocks of wood a minimum of 15.25cm (6") square or Big Foot steady attachments) until they are firmly set against the ground. Please Note: It is possible on very uneven sites that when fully extended blocks may be required under the corner steadies to achieve this. It is important that the caravan is correctly levelled to ensure the correct working of the refrigerator, cooker etc. (iv) Now that your caravan is level, place the caravan step in front of the door ensuring that it is stable and safe to use. PARKING ON A REVERSE-SLOPING SITE OR STEEP HILL For successful parking on a reverse slope or steep hill, the operator need only apply the handbrake with one hand while gently but purposely inching the caravan a small distance backwards with the other. CAUTION Never enter the caravan without first lowering the four corner steadies with the 5-1

20 ARRIVING ON SITE brace provided. Corner steadies should not be used as a jack. Take care not to lift the caravan wheels. 5-2

21 GETTING STARTED GETTING STARTED You have arrived at your destination and now want to start to enjoy your new Compass caravan. The following is a step by step guide to connecting your services and getting everything in your caravan working. ELECTRICITY Power Supply Charger Your caravan is fitted with a power supply/ charger. This will charge the caravan battery when fitted and also power the 12V systems in your caravan. It is recommended that you always carry a leisure battery. The Charger is fully automatic and will not overcharge the leisure battery. 12v Systems: Your caravan is fitted with an automatic system for selection of power. When connected to the 230V site supply the automatic Power Supply/Charger will charge the leisure battery and the 12V systems. When connected to the car (always disconnect 230V supply), the system automatically switches to the car supply. When the ignition is switched on the 12V system in the caravan is automatically switched off, car power is supplied to the refrigerator and battery charging is in operation. AC or DC and whether it is at the correct voltage and frequency. (ii) Your caravan is properly earthed. Never accept a supply from a socket outlet or plug having only two pins, or from a lighting outlet. (iii) Any residual current device (earth leakage circuit breaker) in the mains supply to the caravan has been tested within the last month. In case of doubt, consult the site owner or their agent. (iv) Make sure that the switch at the site supply point is off and that all electrical equipment in the caravan is switched off by ensuring your caravan mains isolating switch on the MCB is in the OFF position. ELECTRICAL WARNING Attention: Always disconnect the electrical connector between the towing vehicle and the caravan before connecting a mains electric supply to the caravan and before charging the caravan battery by any other means. Once the above checks have been made: (v) Remove any cover to the electricity inlet provided on the caravan, and insert the female connector of the flexible orange supply cable as shown. GENERATOR/CHARGER When connecting to a generator, always switch off the RCD, start the generator and allow running for a few minutes to stabilize. When this has happened, switch the RCD to the ON position. ELECTRICITY MAINS SUPPLY Your caravan s main electrical installation is designed to run on 230V at 50 hertz AC supply. CONNECTING TO MAINS SUPPLY ON ARRIVAL AT SITE Before connecting the caravan installation to the mains supply, check that: (i) The mains supply is suitable for your installation and appliances, i.e. whether it is (vi) Locate the site supply and remove any cover from the socket outlet provided at the supply point. Insert the male plug at the other end of the flexible orange supply cable. Switch on the main switch at the site supply point (if appropriate). 6-1

22 GETTING STARTED WIRING OF CONNECTING CABLE AND CARAVAN MAINS INLET WARNING: It is essential that connections are made exactly as shown. If terminal markings are not in accordance with the above diagram they must be ignored. (vii) Place any surplus cable under the caravan. Ensure that the surplus cable is not coiled up as it could overheat. (viii) The MCB main electricity supply switch should be put in the ON position. (ix) Check the RCD is working by pressing the test button. Once pressed all electrical lights and appliances should cease to operate. Reset, and then check the electrical system is operational. (x) Finally in order to get your 12V system operational, ensure the master 12V switch is in the ON position. Refer to index for further details on the control panel fitted. DISCONNECTING MAINS SUPPLY WHEN LEAVING SITE (i) Switch OFF at the caravan mains isolating switch. (ii) Remove the male plug from the site supply. (iii) Disconnect the female plug from the caravan and store the cable in an appropriate locker. OVERSEAS ELECTRICAL CONNECTION Please Note: Connection to a mains voltage supply OVERSEAS requires particular attention. Care must be taken when connecting supplies abroad since the supplies can be of REVERSE POLARITY. The significance of REVERSE POLARITY is that when equipment is switched off, it may not be electrically isolated. The only certain way of making equipment safe is to unplug it. A means of checking the polarity of the mains supply when overseas is recommended. There are available several proprietary makes of equipment for the purpose. If it can be achieved, it is preferable to connect live to live, and neutral to neutral to maintain full electrical protection. CHECK all caravan equipment is set-up to accept the site supply before actually switching on. 6-2

23 GETTING STARTED GAS SUPPLY Your caravan is designed to operate using either propane or butane liquefied petroleum gas at 30M/bar. Gas can be obtained from your caravan dealer. Your caravan is designed to accept a maximum 2 x 6kg Truma gas bottles. Connection Make sure that heating and cooking appliances and gas cylinders are switched off. Each gas appliance is connected to its own gas isolation tap under the cooker. These are identified on the tap via a label. Below is a key to identify each label. To operate the tap the arrow on the tap shows the direction of flow for the gas. The arrow should be pointing towards the appliance for the appliance to operate. There will be a small label next to the bank of taps under the cooker, which is also reproduced below: Water Heater Space Heater Refrigerator Changing a Gas Cylinder Cooking Appliance Hob Gas On/Off Before commencing to change a gas cylinder ensure that the valve on the cylinder is turned fully off. Turn off all gas operated appliances. Remove the gas hose from gas cylinder. Before refitting a gas cylinder, ensure that all gas operated appliances are turned off - particularly after winterisation. Ensure all connections are secure. WARNING: If cylinders other than those recommended are used, ensure that the cylinders are adequately supported, do not block ventilation openings and cannot cause damage to fixtures and fittings located in the compartment. Gas Regulator Your new Compass caravan has been fitted with a fully approved gas regulator designed to operate at a gas pressure of 30Mbar. Your regulator is fitted with a test point, which is accessed via the inlet at the side of the regulator. This access point is only for carrying out gas pressure tests and should not be used for any other purpose. CAUTION It is strongly recommended that only CORGI approved gas fitters carry out any work on your caravan gas installation. High Pressure Gas Hoses You should only connect to this regulator using a length of approved high-pressure hose not exceeding 450mm from the gas cylinder to the regulator. These approved high-pressure hoses are available from your Compass Retailer. These hoses are connected using screw thread fittings, which will make a seal if connected and tightened using a spanner. Once the hose is securely connected turn on the gas tap above the regulator, then turn on the gas bottle to allow gas to flow into the caravan. In order to make all your caravan gas appliances operational it is necessary to open each appliance gas tap as detailed in previous column. All your gas appliances should now be operational. Instructions on how to use each appliance are detailed later in your handbook. WARNING: Aerosols and highly flammable liquids must not be stored in the compartment behind, or adjacent to, any gas appliance. Some industrial LPG appliances operate at high pressure and require a high pressure regulator. This often has an adjusting handle on it. NEVER use such a regulator on a caravan. Ventilation holes must be clear at all times. 6-3

24 GETTING STARTED WATER SYSTEM Your new Compass Caravan is fitted with the Whale Aquasmart water system incorporating the Smartflo pressure pump to provide a reliable, high rate for superior showering. To achieve the best performance from the Smartflo pump please follow the priming instructions below. When the system is first used or if air is sucked into the system when emptying your water container: Insert plug into wall socket and close lid to lock plug in place. Place carbon filter which is fitted to the hose into the water container. Switch on the 12V supply to pump. Open the farthest away hot water tap from the pump. When the water is flowing smoothly close hot tap and open the cold tap to expel the remaining air. Repeat points 4 and 5 for the second farthest away tap from the pump, until the closest tap if finally purged of air. Note: Following these instructions will maximise the performance of your pump. Ensure all your taps are in the off position and the pump is turned off, and then connect your external water container to the water inlet using the connection hose supplied. Switch the pump switch on the control panel to on and the red light should illuminate. The pump will run until the correct pressure has built up in the system. Once the pump switches off your water system is ready to use. Please note, it will take at least 30 minutes for your water heater to heat the water in its holding tank to the expected temperature. When you open a tap the pump light should illuminate and the pump run while the tap is open, the pump may run for a short time after the tap is closed in order to build up the correct working pressure again. How to Use Your Aquasource CAUTION Do not under any circumstances connect your caravan to the mains water supply without the pressure reducer fitted. Damage will occur to the caravan s water system! Max. working inlet pressure: 7 bar. Static pressure: approx bar Connection to your water inlet (i) Uncoil the hose and screw tap adaptor to the drinking water stand pipe and plug in the hose adaptor. (ii) Raise the lid; clean both the water socket and the Aquasource plug. Push the plug into the socket. Turn on the mains water supply and check for leaks. Open one of the taps and purge any air that may be trapped in the water system. To remove, pull the lower trigger and pull out the hose plug. Draining Down Your Water System (i) It is essential that you drain down your caravan water system when it is not in use. This is most important during winter months to protect against frost damage. (ii) Disconnect the water pump and switch off power supply. (iii) Remove the water heater fuse from the switch spur and store in a safe place. (iv) Open the safety drain valve on the water heater located next to the water heater. (v) Open all taps and remove all plugs from sinks and showers. Lever operated taps should have the lever put into the up and central position. (vi) Open the drain outlets on the outside of your caravan. (vii) Adjust the level of the caravan to ensure that the drain outlet is at the lowest point of the caravan. This will aid the flow of water to ensure all water is drained off. (viii) After 30 minutes level the caravan and prepare it for storage if necessary. 6-4

25 GAS SAFETY ADVICE GAS SAFETY ADVICE In the event of a suspected gas leak the gas must be turned off using the isolation valve on the gas bottle. A competent gas fitter should then check the system before it is used/reused. Regularly check flexible gas hose, joints and connections for tightness. Finally, make sure that each gas appliance is working efficiently to the recommendations of the appliance manufacturers. See Index - Ventilation FACTS ABOUT LPG LPG is not poisonous. Bi-products are harmless. LPG is dangerous if all air and oxygen is excluded. LPG has been given a smell by the manufacturers in order to identify leaks. The gas is heavier than air and therefore sinks to the lowest point. AWNING SPACES, LPG AND APPLIANCE EXHAUST There is no danger of pollution of an enclosed awning space from the LPG exhaust from a refrigerator venting into it. Space heaters may produce sufficient exhaust to pollute the awning space, if it is totally enclosed, from a general comfort, smell and hygiene point of view. In extreme cases there could be a build up of carbon dioxide to a dangerous level. Caravan owners are advised to allow some fresh air circulation in the awning space when such appliances are in use. Please Note: Ventilation holes must be clear at all times. LPG GAS SYSTEM Compass does not recommend the use of any external cylinders. All cylinders in use should be within the gas locker provided. If you wish to utilise a larger cylinder and have this outside the gas locker then the connecting hose must not exceed 750mm. It is recommended that no flammable material is stored or placed within 300mm of any open flame. Your attention is also drawn to the fact that the surface of the Space Heater in your caravan will get hot when in use. You are advised not to use any additional gas appliances outside your caravan unless it is a Gas Barbecue connected via the Barbecue point supplied with your caravan. Please ensure that you have read the operating instructions for each gas appliance contained in your Owners Information Pack. Please ensure that any gas hose left unconnected is protected from dirt or other foreign bodies entering the hose. GAS BARBECUE POINT Your caravan is fitted with a gas barbecue point. The gas barbecue point, when fitted, is situated on the nearside towards the front. This point is for use with a gas barbecue only. Simply lift up the flap, unplug the red plastic end cap and connect the appliance in accordance with the gas barbecue manufacturer s instructions. CAUTION: Do not use a gas barbecue inside the awning. ALWAYS use the appliance in the open air. There will be an isolation valve fitted next to the Barbecue point. This is an automatic valve, which cannot be operated unless a connection has been made to the Barbecue point. Do not apply any force to this value. WARNINGS Fresh air circulation should be allowed below the caravan when appliances are in use and when flues terminate below the floor to allow free evacuation of the products of combustion. At least three sides of the underfloor space should always be kept open and unobstructed especially by snow. Do not make any additional openings in the floor. Outlet sockets located within the caravan should only be used with a dedicated appliance and not an independent unit. No appliance shall be used outside when connected to an internal outlet. Maintain adequate spacing of combustible materials from sources of heat. Do not use additional independent gas appliances inside the caravan. 7-1

26 GAS SAFETY ADVICE 7-2

27 ELECTRICAL SYSTEM ELECTRICAL SYSTEM 12v POWER SUPPLY Battery Installation Your caravan will be fitted with a BCA Leisure charging and power distribution unit. If you wish to install a leisure battery please ensure that it is placed on the battery tray supplied with your caravan. Then place the tray in the battery locker fitted to the side of your caravan. Connect the battery to the clamp fittings connected to the connection leads within the battery box. Compass recommends that you use sealed for life leisure batteries of a minimum rating off 40 ampere-hours at 20 hours discharge rate. Battery Maintenance Your leisure battery should be maintained in accordance with the manufacturer s instructions. For information on the automatic charging system in your caravan please refer to Automatic Charging System in the index. Do not charge your leisure battery with any charger other than that supplied. Failure to comply may cause damage to your battery. If you remove your leisure battery, ensure that it is not placed on a cold surface as the battery will deteriorate more rapidly than if stored at a suitable temperature Generators / Charger All electrical equipment fitted in your new caravan can be run from either a controlled generator or charger whose output is maintained between 11volts and 14volts. At least once every 3 years, the caravan electrical installation should be inspected and tested, and a report on its condition obtained, as prescribed in British Standard BS v POWER SUPPLY Mains Unit The Mains Unit replaces the conventional fuse box. Similar, but larger ones are often fitted in new houses. The unit, normally located in the wardrobe, gives overloads and earth leakage protection for the 230V electrical supply in your caravan. For normal operation all switches on the unit need to be in the ON position. The switches on the left of the unit are known as MCB s (miniature circuit breakers). These take the place of the conventional fuse but are more convenient. In the event of a fault the MCB trips i.e. automatically moves to the OFF position. After elimination of the fault the MCB can be re-set by switching to the ON position (against the spring pressure in an upwards direction). If an earth fault develops, or a person was to touch a live piece of equipment, the leakage of current to earth should immediately operate the RCD (residual current device) and trip the main switch, to the OFF position. This switch can only be re-set after elimination of the fault. Please Note: In case of difficulty, consult an approved electrical installation contractor (who may be the local electricity board). It is dangerous to attempt modifications and additions yourself. Lamp holder-plugs (bayonet- cap adaptors) should not be used under any circumstances. Resetting the RCD To re-set, operate the switch as for MCB s. Periodically, the RCD should be checked by operating the test button marked T. The unit should immediately switch to the OFF position. If the unit does not switch off then a qualified electrician should be consulted. If the unit does switch off, the test is complete and the switch can be re-set restoring the supply back to normal. Please Note: Simultaneous operation of all of the 230V mains electrical equipment may not be possible. A typical UK caravan site mains hook-up point provides a maximum output of 10 amps and on some continental sites the available output may be as low as 5 amps. If your loading exceeds the site supply it may trip the site circuit breaker. Please check the available mains output with your site operator. The following items need to be added together if used simultaneously. 230V mains equipment typical consumption figures: Refrigerator amps Charger amps Water heater amps Blown air heaters amps Colour TV amps Microwave amps 8-1

28 ELECTRICAL SYSTEM AUTOMATIC CHARGING SYSTEM The battery charger will operate automatically when the caravan is connected to the mains outlet on a caravan site. The 12V system, with the exception of the 12V refrigerator and battery charging, will not operate when the caravan is connected to the towing vehicle. CHECK all caravan equipment is set-up to accept the site supply before actually switching on. MAXIMUM BULB RATINGS FOR INTERNAL LIGHTS Type of Light Maximum Bulb Rating Compact Fluorescent... 9W Reading Lights... 10W Downlighters... 10W Dinette soffet lights... 20W Bedroom lights... 10W Please Note: Ensure that you only replace a blown bulb with one of the same rating. Never replace a bulb with one with a higher rating. You should ensure that when fitted, no bulb is in contact with the surface of the lamp or shade. Connecting a Solar Panel and/or Satellite Dish If you ordered your caravan with the entertainment pack option fitted then your caravan will have both a solar panel connection point and a satellite TV connection point within the battery box. Solar Panel Connection To connect a solar panel insert the panel connection lead into the connection point within the battery box, please ensure that you have a regulator in line whenever a solar panel is connected. Satellite TC Connection To connect a Satellite TV receiver simply insert the satellite connection into the connection point within the battery box and this will feed the satellite signal to the TV outlets within your caravan. You will need to fit the satellite decoder between the aerial outlet and your TV. 8-2

29 ELECTRICAL SYSTEM 12V FUSES - ALL MODELS 8-3

30 ELECTRICAL SYSTEM MAINS UNIT 8-4

31 HOW TO USE YOUR CARAVAN S EQUIPMENT HOW TO USE YOUR CARAVAN S EQUIPMENT Congratulations on your purchase of a new Compass caravan. Within this section of your caravan s handbook we will give you brief details on how to operate all of the caravan s equipment from the gas cooking equipment to the widow blinds. For further details on the major equipment within your caravan please read the individual appliance instructions contained with your user information pack. Please Note: Before attempting to use any gas equipment please ensure that the gas bottle is connected securely to the caravan s regulator via a high pressure gas hose and the bottle valve is in the on position. Also ensure the appliance isolation valves are in the on position as shown in the gas system section. Please Note: Before attempting to use any electrical appliance ensure that you have connected the mains connection cable to a mains hook up and that the mains isolation switch is in the on position. ELECTRICAL CONTROL PANEL Omega Your new Omega Caravan will be fitted with the control panel shown below Control panel for caravans without a fixed water tank. (i) To operate the 12V systems for your caravan depress the left rocker switch. (ii) To operate the pump for your water system depress switch marked with a tap symbol. (iii) When the pump is running the neon light will illuminate. (iv) When the left hand button is depressed the available battery Voltage will be displayed. (v) The right hand button has no function on this control panel. 9-1

32 HOW TO USE YOUR CARAVAN S EQUIPMENT COOKING EQUIPMENT WARNINGS (i) All pans should be mounted centrally over the burners, even when cooling, to protect adjacent walls. (ii) Do not lower the glass cover until hob has cooled down. (iii) Glass lids may shatter when heated. Turn off all burners and grill before shutting the lid. The glass cover should be raised when operating the grill. (iv) Accessible parts may be hot when the grill and oven are in use. Young children should be kept away. (v) Do not use grill or oven as a space heater. (vi) When you are cooking it is essential to provide additional ventilation, such as opening windows near grill, cooker and oven. Gas Hob (i) Turn the individual control knob for the burner you wish to light. (ii) If the hob is fitted with electronic ignition then depress the ignition button, which can be found on the front of the oven next to the oven control, while depressing the control knob. The depressing of the control knob overrides the flame failure device fitted to the burner. If the burner fails to light within 20 seconds then release the control knob and wait 30 seconds before trying again. (iii) Once the burner lights it will be necessary to keep the control knob depressed for about 5 to 10 seconds to ensure that the flame failure device is heated up enough to operate. Gas Grill (i) Turn the grill control knob to the high flame position and with the knob depressed press the electronic ignitor button. If the grill does not light within 20 seconds then turn off the grill control knob for at least 30 seconds before trying again. (ii) Once the grill lights it will be necessary to keep the grill control knob depressed for 5 to 10 seconds to ensure the flame failure device is heated enough to operate. Grill control knob Burner controls Ignitor button 9-2

33 HOW TO USE YOUR CARAVAN S EQUIPMENT Gas Oven (i) Turn the gas oven control knob to maximum then depress the knob while pressing the electronic ignitor button. If the oven does not light within 20 seconds turn off the control knob and wait for 30 seconds before trying again. (ii) Once the oven is lit it will be necessary to keep the control knob depressed for 5 to 10 seconds to ensure the flame failure device is heated up enough to operate. Oven control knob 9-3

34 HOW TO USE YOUR CARAVAN S EQUIPMENT REFRIGERATOR MODEL THETFORD N112 LCD A = Main switch (on/off) B = Mode selection switch C = Cooling level selection switch D = Function LED E = LCD display OPERATING INSTRUCTIONS When the caravan is on tow, the refrigerator should only be operated electrically, i.e. from the 12V battery in the towing vehicle and not by means of the bottled gas. The refrigerator can be run on 230V or LP gas whilst stationary. CAUTION: Only use one source of energy at a time. WARNING: The refrigerator should not be operated on LP gas whilst being towed or when on a petrol station forecourt. Switching on the refrigerator Clean the inside of the refrigerator before you switch it on. Let the refrigerator run for at least eight hours before you place food in it for the first time. SMART ENERGY SELECTION (SES) When you start up the refrigerator (equipped with Smart Energy Selection (SES)) you should usually select the AUTO mode. The SES system will then automatically select the best of the three available energy sources. The system will apply the following priority: - mains voltage (230V) - direct current (12V) - liquid gas If an energy source becomes available that has a higher priority than the source the refrigerator is currently using (e.g. if your vehicle engine is started), the system will stop using the current energy source and switch to the energy source with the higher priority. If a fault occurs in one or more of the possible energy sources, the system will not generate an error message while an alternative energy source is still available. The SES system switches over automatically. Note: If none of the energy sources are available, the blue LED flashes every second and an error code is shown in the display. Automatic models additionally allow you to select the desired energy source manually. Important: The memory of the SES system saves every change made to the setting. Consequently, the SES system will start up on each subsequent occasion in the last-selected setting. 1. Open the valve of the gas bottle. 2. Open the taps of the gas supply. 3. Press main switch (A). The function LED will turn blue and all symbols on the LCD display will light up. 4. Use the mode selection switch to select the "Auto" function or one of the power supplies that you want. The LCD display will show the option you have selected. 5. Set the desired refrigerating cooling level by 9-4

35 HOW TO USE YOUR CARAVAN S EQUIPMENT means of the cooling level selection switch (C). The LCD display will show the cooling level setting you have selected. A. Use the main switch to switch the refrigerator on and off. The function LED will turn blue. The display LCD shows the most recent settings. After 10 seconds the LCD display's backlight will go out. The function LED remains blue. B. Press the mode selector switch and the LCD display backlight will show the setting for 10 seconds. Pressing the mode selector switch successive times takes you through the menu in the following sequence: AUTO, manual DC (12V), manual gas, manual mains voltage (230V) and back to AUTO. Select either the AUTO option or one of the other power supplies that you want to use. The LCD display shows the option you have selected. If you select the AUTO option, the system will choose the most suitable power supply and the AUTO symbol and the symbol of the power supply chosen by the system will both be shown on the LCD display. Ten seconds after release of the mode selector switch, the system will switch off the LCD backlight. C. Use the cooling level selector switch to control the temperature of the refrigerator. When you press the cooling level selector switch, the LCD backlight will light up and show the currently set temperature. Every time you press the cooling level selector switch again, you set the refrigerator one position cooler. On reaching the coldest temperature, the system will start again at the warmest temperature setting. Ten seconds after release of the cooling level selector switch, the system will switch off the LCD backlight. POWERING WITH ELECTRICITY Powering with electricity can be selected both by the Auto mode (only Automatic fridges) and manually. Auto mode Mains voltage (230V): This energy source will be selected if the mains voltage is greater than 200V. This power supply requires a continuous current of 12V to operate the electronic control system. Direct current (12V): The SES system will select 12V powering only if a mains voltage (230V) is unavailable, the vehicle engine is running and a voltage higher than 11V is available. If a fault occurs during electrical powering (230V or 12V), an error message will not be shown on the display as long as another energy source is available. The system will automatically switch to the available energy source that has the highest priority. Selecting electrical power manually Mains voltage (230V): The LED warns you whenever insufficient voltage is available or if a fault occurs. If this happens, the LED will start flashing once per second and an error code is shown in the LCD display. When sufficient current is available again, or the fault has been resolved, the LED will emit a steady blue light again. Direct current (12V): The LED warns you whenever your vehicle's engine is not running, or if a fault occurs, or if sufficient voltage is available. If this happens, the LED will start flashing once per second and an error code is shown in the LCD display. Once the engine is running, or the fault has been resolved, or sufficient voltage is available again, the LED will again emit a steady blue light. NB: If the refrigerator has been manually set to operate at 12V, it will not automatically switch to another energy source when your vehicle's engine is not running. In this case, the refrigerator will stop cooling. POWERING WITH GAS Powering with gas can be selected both by the Auto mode (only Automatic fridges) and manually. Auto mode The system will select gas operation if mains voltage (230V) is unavailable; or the vehicle's engine is not running. Once mains voltage (230V) is available again or the vehicle's engine is running, the system will switch to the available energy source that has the highest priority if the fridge is in Auto mode. If the refrigerator switches from 12V DC to gas operation when it is in auto mode, the system will wait for about 15 minutes before igniting the 9-5

36 HOW TO USE YOUR CARAVAN S EQUIPMENT gas. During this time, however, the gas indicator lamp will come on. The delay is built in to avoid it switching to gas operation whenever you stop to refuel your vehicle. You can cancel the delay by immediately switching the refrigerator off and then on again. If the system selects gas operation, the ignition will be activated automatically. The gas will flow to the burner and be lit by the electric ignition. If the flame goes out, the gas will immediately be lit again. Selecting gas operation manually If the flame cannot be lit within 30 seconds, the gas supply will stop and gas mode will be switched off. The LED will start flashing every second and an error code is shown in the LCD display. The gas mode can be reset only if the refrigerator is switched off. If you switch the refrigerator on again and the gas mode is still not working, the LED of the manual gas mode will flash to indicate that gas is unavailable and an error code is shown in the LCD display. Switching off the refrigerator Push the main switch (A). The blue LED will go out. The refrigerator is now completely switched off. Use the special storage latch on the door locking mechanism to fixate the open door. This prevents unpleasant odours and mould in the refrigerator. Securing products for driving system consists of a simple click-and-slide plastic strip. To secure products on the rack while driving, push the plastic strip as tightly as you can against the products on the rack. In the storage space on the inside of the refrigerator door, there is the unique Thetford flexible bottle slide. The slide prevents bottles from sliding around during driving. Push the slide against the products in the door or place the products between the bottle slide. Door locking mechanism The refrigerator door has an automatic locking mechanism. The door locks automatically when you press it shut firmly. The lock releases unnoticed when you open the refrigerator with your hand. This automatic locking mechanism also keeps the refrigerator door shut during driving. For some models an additional security device is fitted below the refrigerator. By pushing the locking bar over the pin when the door is closed, you can make doubly sure that the door does not come open during your journey. One of the racks in your refrigerator has a system for securing products during driving. The 9-6

37 HOW TO USE YOUR CARAVAN S EQUIPMENT TROUBLESHOOTING Before calling the authorised Service Department please check whether: The instructions in the section Using the refrigerator have been followed. The refrigerator is not tilted excessively. It is possible to operate the refrigerator with an available power source. Failure: The refrigerator does not work in gas operation mode. a) Gas bottle empty. a) Change gas bottle. b) Is the supply cut-out device open? b) Open the cut-out device. c) Air in the gas pipe? c) Switch device off and on again 3-4 times to remove air from the gas pipe. Failure: The refrigerator does not work on 12V. Possible cause Action you can take a) On-board fuse defective. a) Fit new fuse. b) On-board battery discharged. b) Check battery, charge it. c) Engine not running. c) Start engine. Failure: The refrigerator does not work on 230V. Possible cause Action you can take a) On-board fuse defective. a) Fit new fuse. b) No connection to supply voltage. b) Establish power connection. c) AES: gas operation despite c) Appliance switches to gas connection to the supply voltage? operation due to insufficient supply voltage (automatically switches back to 230V operation). Failure: The refrigerator does not cool sufficiently. Possible cause Action you can take a) Inadequate ventilation to a) Check that the ventilation the unit. grilles are not covered. b) The thermostat setting is b) Turn the thermostat to a too low. higher setting. c) There is too much ice on c) Check that the refrigerator the condenser. door seals when shut. d) Too much warm food put d) Let food cool down first. inside. e) Appliance running for a e) Wait several hours, check short time. again. 9-7

38 HOW TO USE YOUR CARAVAN S EQUIPMENT MAINTENANCE Works on gas components and electrical installation may only be carried out by authorised personnel. We recommend to contact your Dometic Service Centre. EN 1949 stipulates that the appliance s gas equipment and its associated fume system must be inspected after installation and a certificate issued. Afterwards a qualified technician must inspect according to EN 1949 every two years and a certificate issued. It is the user s responsibility to arrange for inspections after purchase. It is recommended that the gas burner be inspected and cleaned as necessary at least once a year. We recommend maintenance following an extended shutdown of the vehicle. 9-8

39 HOW TO USE YOUR CARAVAN S EQUIPMENT WATER HEATER OPERATION Gas operation SPACE HEATER OPERATION Gas Operation Ultrastore Control (i) Ensure that the water heater has been filled with water and that the outside flue cover has been removed. (ii) Using the Ultrastore control knob, turn the dial to the desired temperature setting then turn the outer ring to the flame position. (iii) Once the Ultrastore is switched on a green light is visible within the switch and the unit will now try and ignite. (iv) If within approximately 10 seconds, the Ultrastore fails to ignite then a red failure light will also appear. If this happens wait 30 seconds before trying again. 230V Operation (i) Simply depress the Electrical switch fitted next to the gas control to the 230V position. This will turn on the water heaters electrical element. It is imperative that there is water in the heater whenever the Gas or Electric is switched on. Gas Control (i) Turn the gas control on top of the heater to the desired setting and depress the knob. (ii) Keeping the control knob depressed look into the viewing window and see if the gas ignites. You should be able to hear it ticking until the pilot light ignites. (iii) Once the pilot light is lit keep the control knob depressed for a further 20 seconds to allow the thermocouple to operate. (iv) If the heater fails to ignite please wait 20 seconds before trying again. 230V Operation Ultraheat Control (i) Simply depress the main switch on the Ultraheat control panel to the 230V position. (ii) Then set the power rating you require on the panel at either 500w 1000w or 2000w. 9-9

40 HOW TO USE YOUR CARAVAN S EQUIPMENT Fan Operation The blown air function of the space heater is controlled by the three position switch on top of the heater. MICROWAVE Note: Your microwave is connected to your 230V electricity supply via a non customer useable plug. Fan Control (i) Position 0 is off (ii) Position A operates the fan in automatic mode. In this position the fan will only run when there is sufficient heat to require the air to be circulated. (iii) The third Position will operate the fan at all times. (iv) The speed of the fan is controlled by the number position set with 5 being the fastest speed and 1 being the lowest. WARNING: The space heater surfaces become hot in use and the guard provided does not give full protection to the young or elderly. Controls: Time + Button increases the duration of operation. Time - Button decreases the duration of operation. Power button sets the power level for the microwave. Stop button can be used to stop the microwave before the full time set has elapsed. Start button sets the microwave working for the time set. 9-10

41 HOW TO USE YOUR CARAVAN S EQUIPMENT BATTERY CHARGER The battery charger for the caravan battery will automatically switch on when the caravan is connected to a mains supply. The battery charger will also provide a 12V supply to the caravan when a battery is not connected. Please note that the battery charger fitted is designed to keep your battery charged and is not designed for charging up a flat battery. SMOKE DETECTOR The caravan smoke detector will become active once the 9V battery which should be supplied with the smoke detector is connected. The smoke detector fitted to your caravan has an alarm pause mode which will reduce the sensitivity of the alarm for a short period to allow for cooking within the caravan. The alarm pause mode is activated by pressing the button marked HUSH on the smoke detector. While the detector is in the pause mode the detector will beep once per minute to alert that the alarm pause mode is activated. 9-11

42 HOW TO USE YOUR CARAVAN S EQUIPMENT THETFORD CASSETTE C-200 CWE TOILET Introduction The Thetford Cassette C-200 CWE is functional and incorporates modern styling with home like features. The unit is an integral part of the motorhome bathroom. The Thetford Cassette C-200 CWE is constructed of high quality plastics for durability and has a high gloss finish that is easy to clean and maintain. The unit consists of two sections, a permanently installed toilet system and a slide out waste holding tank - the Cassette. The toilet section includes a rotatable bowl, a removable seat, and a control unit with a flush button and a waste level warning device. The valve blade handle is located under the bowl. The cassette is located underneath the toilet and is removed for emptying from the outside of the vehicle through an access door. A rotating pourout spout, automatic holding tank vent, air release valve, valve blade, carrying handles and hand grips are incorporated into the cassette. A sliding cover guarantees optimum hygiene. Features: Removable seat and cover. Rotatable bowl. Valve blade handle: opens and closes valve blade manually. Flush button: activates flush. Waste level indicator: indicates when cassette requires emptying. Rotating pour-out spout: makes emptying cassette easy and convenient. Automatic cassette vent: vents the cassette when inserted in the toilet. This prevents over pressure in the cassette. Upper-carrying handles: makes carrying and emptying easy. Sliding cover: opens and closes automatically when sliding the cassette in and out. Guarantees optimal hygiene. Valve blade and blade seal. Vent button: vents the cassette to avoid splashing while emptying. Handgrip. Valve blade opener. Access door. Locks from outside the motorhome. Preparing for use Following is a brief illustrated step by step guide. For more detailed information please refer to manufacturers literature. CAUTION (step 4): Warmer weather or longer intervals between emptying the waste tank may require additional toilet fluid. Use only Thetford toilet fluid to achieve the best results. Never add toilet fluid directly into the toilet bowl. CAUTION (step 14): Do not depress air release valve button until pour out spout is facing downwards. Emptying the waste holding tank The cassette capacity is approx. 17 litres and the tank should be emptied when the waste-level warning device comes on. This will occur when the tank contains more than 15 litres of waste. Note: After the warning device comes on, the capacity remaining is equal to approximately 5 uses. CAUTION: Do not allow the waste cassette to become overfilled. See trouble shooting section for emergency emptying procedure. Note: Some vehicles are equipped with water pumps supplying high water pressure, which can result in having an over flushing problem. It is possible to use the flow restrictor supplied with the toilet (packed together with the instruction manual) by installing it in the water tube at the connection level. Rinse the holding tank with clean water. Prepare the cassette for use again by following steps 1 to 6. Replace the holding tank and lock the access door. 9-12

43 HOW TO USE YOUR CARAVAN S EQUIPMENT 1 - Open access door and pull retaining clips upward. 4 - Remove dosage cap and pour-out spout. Add toilet fluid in the dosage cup. Add approx. 2L of water through spout to cover tank bottom. Replace cap, return pour-out spout to original stored position. 2 - Remove cassette by pulling straight out. When cassette hits stop, tilt downwards 5 - Slide the holding tank into position through access door. Never force insertion as this can cause damage to the toilet. 3 - Position tank vertically and swivel pour-out spout upwards. 6 - Make sure the retaining clip secures the holding tank. Close and lock the access door. 9-13

44 HOW TO USE YOUR CARAVAN S EQUIPMENT 7 - Open water fill door and add 50ml. of Aqua Rinse. Then fill the tank with fresh water using a jerry can or hose. Tank capacity is 7 litres After use, open the blade, by pushing the blade handle in an anticlockwise direction and press the flush button After flushing, close the blade by pushing the blade handle clockwise. The toilet may also be used with the valve blade open, which allows the waste to pass directly into the holding tank. 8 - Turn the bowl into the most comfortable position, when necessary. 9 - Before using the toilet, we recommend to add some water to the bowl by pressing the flush button. Release button to stop Open access door and remove holding tank. The holding tank can only be removed when valve blade is closed. 9-14

45 HOW TO USE YOUR CARAVAN S EQUIPMENT 13 - Carry the holding tank to a normal household toilet or authorised disposal point. Place holding tank in vertical position and rotate pour-out spout upwards Remove measuring cap. Grasp unit by upper carrying handle nearest pourout spout. Place other hand on upper rear hand grip so that the vent button can be depressed with thumb while emptying. This ensures a smooth outflow of tank contents Once the pump has been cleared of water place appropriate size container under the drain plug. Empty any remaining water from the fresh water tank by taking out the drain plug. Clean the seals and lubricate them where appropriate after drying. Winterising/Storage The Thetford Cassette C-200 CWE is easily winterised for storage. If the toilet is connected to a separate water tank, drain the tank. When the motorhome water tank is empty, press the flush button until the water stops flowing. Empty the cassette. If the toilet is connected to a central water tank, open the electric valve by pushing the flush button while draining the water supply system of the motorhome. Empty the cassette. Leave the blade of the cassette open. Do not replace cap on spout, this helps to keep the cassette dry. Cold weather use The cassette can be used in cold weather when the motorhome is heated. When the vehicle is not heated for more than a day (or a night), winterise the cassette. High Altitude and hot weather use Changes in altitude during driving, and large temperature variations give no problems as long as the cassette is inserted into the toilet. The automatic cassette vent will depressurise that tank when there is over or under pressure. High temperatures may require additional Thetford toilet fluid. Cleaning and maintenance To clean the seal and blade, the use of Thetford bathroom cleaner and rinse with water is recommended. Alternatively, use a luke warm solution of diluted washing up liquid. Do not use household cleaners as they may damage the seals and other toilet parts. Dry the seal and blade thoroughly and spray economically with silicone spray, alternatively use olive oil. Do not use Vaseline or other vegetable oil products. The toilet bowl, seat, cover and the exterior of the toilet unit and cassette can be cleaned with a mild detergent/water mixture. 9-15

46 HOW TO USE YOUR CARAVAN S EQUIPMENT Toilet unit malfunctions Contact your dealer or a Thetford Service Centre. We advise draining the fresh water tank prior to travelling. Antifreeze should not be required if the motor home is heated. If you do wish to use antifreeze, brands containing the following properties may be used in the fresh water tank: Ethylene glycol Mono-Ethylene glycol Propane-diol Glycerol Ethane-diol Glycol Never use alcohol based antifreeze, i.e. Methanol, Ethanol, and Iso-propanol. ROOFLIGHTS Your caravan is fitted with at least one type of the following roof lights. The Omivent (12v) Rooflight The Omivent is a double-glazed roof light constructed from a synthetic ultra-violet screened material. Its side-operating mechanism allows a completely free central opening with built-in fixed ventilation when closed. It operates as an extractor fan and air intake fan. Please note: Do not change the direction of the fan unless it has been switched off O position and the blades have stopped rotating. The Heki 2 Rooflight To open to the tilted position: (i) Press the knob in the toggle catches on either side of the rooflight and turn through approx. 90. (ii) Grasp the metal bar in the middle, snap it out of its holder, swivel down and press the rooflight upwards. (The rooflight is held by the two gas springs after approx. 150mm). (iii) Swivel the metal bar towards the rooflight and snap into its holder. (iv) To close the rooflight, proceed with steps (iiii) in reverse order. To open in the intermediate position: (i) Open the toggle catches on either side of the rooflight. (ii) Grasp the metal bar in the middle; snap it out of its holder, swivel down and press the rooflight outwards. (Rooflight is opened automatically after approx. 150mm by the two gas springs.) (iii) Open both fasteners and swivel the metal strap toward the intermediate position and pull the rooflight down until the metal strap is stopped by the fasteners. (iv) To close, proceed with steps (i-iii) in reverse order. To open in the ventilation position: (i) Open the toggle catches on either side of the rooflight. (ii) Using both hands on the two toggle catches, press the rooflight up about 2cm and fasten the toggle catches in the corresponding setting. (iii) To close, proceed with steps (i-ii) in reverse order. Closing the blinds: (i) Take hold of the end rod (without rocker) in the recessed grip and engage in the opposite end rod (with rocker). 9-16

47 HOW TO USE YOUR CARAVAN S EQUIPMENT (ii) Select the required position (blackout/ flyscreen) by moving both joined end rods together. CAUTION: In extremely bright sunshine, the blackout blind must only be closed two-thirds, and the rooflight must be set in the continuous airing position. Opening the Blinds: (i) Move blind (end rod with rocker) right to the outside. (ii) Hold the recessed grip with one hand; with the other hand, press the rocker and move the blind back (do not let it recoil). CAUTION Do not stand on the acrylic rooflight. Close HEKI 2 completely before moving off. Do not leave your caravan when HEKI 2 is open. Please consult your supplying dealer if you have any problems or defects. Remove any snow/ice or dirt before opening the roof. Do not open when it rains or when there is a strong wind. Mini Heki Rooflight (i) To open, push the large central button. (ii) Whilst depressed, slide the bar to the desired position and locate into the stops provided. The Mini Heki roof light will generally be fitted in washroom areas. WINDOWS Your caravan will be fitted with either Polyplastic; Seitz framed windows, or a mixture of both. Polyplastic Window Opening (i) In order to open the Polyplastic window it is only necessary to move the catch upwards and release the catch from the backing plate. (ii) The Polyplastic window should remain in the open position once opened, however if it does not then tighten the friction control on the window stays to increase the holding force. (iii) The Polyplastic window is also fitted with a night ventilation position where the catch is set to the centre position on the backing plate; in this position it may be possible for rain to enter the caravan in adverse conditions. 9-17

48 HOW TO USE YOUR CARAVAN S EQUIPMENT BLINDS & FLYSCREENS Blinds (i) Pull blind down by its centre catch. Do not pull down by one side of the blind. This will inevitably lead to problems. (ii) Do not allow blinds to spring back freely. Always control them by hand. Flyscreens (i) To operate the flyscreen, either pull the screen fully down, fully up or across, dependant on type of window fitted, and clip into place on the blind/frame. (ii) To release, unclip from the blind/frame. If a cross bar is fitted, gently pull the crossbar downwards towards you and allow the tension of the spring to roll up the flyscreen. (iii) Where a crossbar is not fitted, disconnect from the blind catch and release gently. (iv) It is recommended that blinds are not in the closed position whilst the caravan is moving. Door Flyscreen The exterior door flyscreen can be opened or closed from inside or outside the caravan and does not restrict door openings. When opening or closing the door flyscreen use the finger grip provided. TAPS All the taps are operated by lifting the lever and turning the lever right for cold and left for hot water. In order for the taps to work, the pump switch on the control panel needs to be in the ON position. For caravans with fixed water tanks the taps need to be in the TAPS position. WARNING: The water temperature could be very high so do not lift the lever with the tap turned to the full left position. Kitchen Tap Bathroom Tap Shower Mixer Tap 9-18

49 HOW TO USE YOUR CARAVAN S EQUIPMENT EXTERIOR DOOR RETAINERS The door retainer fitted to your Compass caravan is operated by simply lightly pushing the door to the side of the caravan. The retainer should automatically engage and hold the door in place. To release the door simply pull the lever located on the side of the retainer towards the door and the retainer will release the door enabling it to be closed. INTERNAL DOORS Toilet/Shower Room Doors Toilet/shower room doors are fitted with a lever lock, which is operated by pushing the lever down. The lever is spring-loaded and will return to the closed position upon release. It is recommend that the lever is always used when closing the door. Toilet/Shower Room Doors GAS LOCKER DOOR All caravan models are fitted with a gas strut supported door which will remain in the open position without the need for a holding bracket. This door will remain open unless locked by the key. Please Note: It is important when raising your gas locker door that you do not push the door past the vertical position as this could damage the hinges. Also care should be taken when leaving the door in the open position to ensure that any wind cannot catch the door and push it open beyond the vertical position. OTHER INTERNAL DOORS Other internal doors such as the wardrobe and table storage locker are fitted with a 2-position button lock. Push the button to lock the door and the button should remain flush with the door. Push the button again to release and the button should then protrude from the door surface. Other Internal Doors 9-19

50 HOW TO USE YOUR CARAVAN S EQUIPMENT MAGNETIC CATCHES Magnetic catches work on contact with the metal plate on the rear of the door. Simply close the door until the magnet engages and holds the metal plate. Pulling the door towards you with a moderate force will be sufficient to disengage the magnetic catch and open the door. SPRUNG HINGES BED MAKE-UP Parallel Lounge Overhead lockers will use sprung hinges. These are suitably strong enough when closed to securely retain the door and prevent it from opening in transit. Pulling the handle towards you with moderate force is sufficient to open the locker door and hold it in the open position. SLIDING DOORS The room divider should be held in place during transit by the use of the strap with the stud fastening. When stationary, the room divider can be held shut by contact between a metal plate and magnet. 4 5 The two single beds can be easily converted into a double bed by pulling out the bed slats, stored beneath the chest of drawers or stored in the bed slat box at the front/end of the caravan. Arrange seat cushions appropriately. 9-20

51 HOW TO USE YOUR CARAVAN S EQUIPMENT L-Shape Lounge Double Bed Bunk Beds On L-shaped layout, the bed frame is pulled out from underneath the rear facing seat. Arrange the seat cushions appropriately. Removal of sofa back rest cushions will provide single beds. 4 All high level beds will take a maximum weight of 75kgs / 11 stone. When in use, the high level beds must have the bunk safety boards in place as shown in the diagram. Touring caravans are manufactured with a lightweight construction and therefore the beds are not designed to be knelt, sat or stood upon without all the bed cushions in place. 9-21

52 HOW TO USE YOUR CARAVAN S EQUIPMENT REMOVABLE DRAWER LOCKER To remove from the caravan, first locate the two retaining straps at the bottom rear of the unit, the straps are released by pulling away and down this releases the thumb catches. The locker can now be removed for storage. To secure the unit into the caravan, first place the locker into position, then feed the straps though the thumb locks, holding the strap taut push the thumb lock so that is closes on the strap. TV AERIAL Status 530 Directional Antenna Your new Compass caravan will be fitted with a 530 Status TV aerial To operate your 530 Directional TV aerial follow the procedure outlined below: (i) Firstly determine the approximate location of the nearest transmitter and whether the signals are horizontally or vertically polarised. For assistance ask your park operator or check other antennas in the vicinity. (ii) Loosen the mast locking collar and wall bracket and raise the antenna. Turn the mast to direct the antenna towards the TV transmitter. The RED SPOT on the bottom of the mast indicates the front of the antenna. (iii) When receiving vertically polarised signals. Rotate the winder anti-clockwise to cant the antenna through 90 degrees. Do not over tighten or use undue force on the winder. DO NOT cant for vertically polarised signals with the TELESCOPICS EXTENDED. (iv) Switch on the power pack and the red LED will illuminate. (v) Check the gain control switch is set to normal NML for use. (vi) Tune your television into the strongest signal. You may need to adjust the direction of the mast to achieve the best picture quality. (vii) Secure by tightning the mast locking collar and wall bracket. VHF Television Reception (Overseas only) (i) Extend the two telescopic antennas. (ii) Tune your television into the strongest signal. You may need to adjust the direction of the mast to achieve the best picture quality. (iii) For fine tuning of VHF you may also need to adjust the length of the telescopic antennas. Please Note: VHF TV transmissions are only horizontally polarised. ENTERTAINMENT SYSTEM Radio/DVD If you ordered the entertainment option with your new caravan then details on how to set up and use the Radio/DVD will be contained in your document wallet. LCD TV If you have ordered an LCD TV with your new caravan then details on how to set up your TV will be supplied with the TV. 9-22

53 HOW TO USE YOUR CARAVAN S EQUIPMENT Please Note: For information on the entertainment equipment provided in your caravan please refer to the instruction manuals provided in your owners information pack. BPW NOSE WEIGHT INDICATOR JOCKEY WHEEL The indicator, which is an integral part of the jockey wheel, will give an estimate of the noseweight of the caravan. The measured value, maximum 125 kg, corresponds approximately to the supporting load of the ball coupling. For a measurement please ensure that: (i) The caravan is standing on horizontal ground. (ii) The caravan is standing horizontally, corresponding to a distance between the lower edge of the ball coupling and the ground of approx mm. (iii) The jockey wheel is only extended up to 70 mm. (iv) The wheel of the jockey wheel is showing to the rear of the caravan. EXPLORER PROTECT - AUTOWATCH ALARM SYSTEM The Explorer Protect system is fitted as standard on the Omega range. Manufactured by Autowatch, The Explorer Protect system is designed to give years of trouble free operation. Made with only the highest quality components and using state of the art technology you can be assured that your caravan has the best electronic protection available. Each caravan alarm is installed with a Passive Infrared Detector (PIR), a wireless sensor that detects movement in the caravan and transmits a radio signal to the alarm module. If the alarm is on the siren will sound. A leg sensor, fully sealed against dust and water, will detect if the corner stabilising leg is being raised or lowered and transmits a coded radio signal to the alarm. Additional sensors can be purchased from your retailer to enhance security. See section below for operation or consult the manufacturers instructions provided in the Owners Information Pack. Basic Operation Arming the System (i) Briefly press (large) arm/disarm button. (ii) Single chirp. (iii) Awning light illuminates for 30 seconds. (iv) Settling time of 15 seconds before responding to triggers. (v) Single intermittent flash of status LED (every 2 seconds). (vi) All sensors triggered will result in siren sounding for 30 seconds, or until reset by pressing the arm/disarm button. Disarming the System (i) Briefly press the (large) arm/disarm button. (ii) Double chirp. (iii) Awning light illuminates briefly on and off and then on again for 30 seconds. (iv) LED off. Panic Alarm (i) Press and hold the small panic button on the transmitter for two seconds. (ii) The siren will sound for thirty seconds, unless reset by pressing any of the transmitter buttons. 9-23

54 HOW TO USE YOUR CARAVAN S EQUIPMENT Emergency Disarm Insert the touch-key briefly into the socket. The alarm will turn off. Silent Arm and Disarm (i) Press the small button briefly followed by a press on the arm/disarm button. (ii) The alarm will arm/disarm without chirps. Sensors Each caravan alarm is installed with a Passive Infrared Detector (PIR) and a leg sensor. Additional sensors can be purchased from your dealer to enhance security. Passive Infra Red Sensor The wireless PIR sensor will detect movement in the caravan and transmit a radio signal to the alarm module, if the alarm is on the siren will sound. Leg Sensor The leg sensor will detect the corner stabilising leg being raised or lowered and transmit a radio signal to the alarm. The leg sensor is fully sealed against dust and water and has a battery life expectancy of three years. When the battery becomes exhausted, the sensor will need to be replaced. Enhanced Features Arming The System In At Home Mode In the at home mode, any sensor that is programmed to be isolated, such as the PIR sensor will not trigger the alarm. Other sensors, such as the leg sensor, will trigger the siren. Arm as normal followed by a second press on the arm/disarm button within 2 seconds. Normal on tone followed by at home tone indicating isolation is active. Settling time of 15 seconds before responding to triggers. Armed in the isolation mode will be indicated by a double flash intermittently of the LED. The at home sensors will be isolated; other sensors will trigger the siren for 30 seconds. Arming the System in Test Or Buzz Mode In the buzz mode the siren will sound a short tone when a sensor is triggered instead of sounding for 30 seconds. It is advisable to test all the sensors. BPW INTELLIGENT DRIVE CONTROL (IDC) SYSTEM If you have ordered your caravan with the safety and security pack it will be fitted with the BPW idc system and here are some simple instructions on how it operates. (i) The sensors of the idc system continually measure the lateral accelerations of the caravans axle(s). (ii) The idc system immediately detects any risk of snaking and automatically and gently applies the caravan brakes. The gentle braking pulls the caravan back on track. (iii) idc makes caravan maintenance easier by detecting slack in the braking system. (iv) In the event of a power failure the idc fails safe so that it automatically returns to the starting position and the service brake is released and remains fully functional. For full operating instructions please read the idc document supplied within your document wallet. 9-24

55 SECURITY SECURITY Theft deterrent, prevention and security of your touring caravan is taken very seriously at Compass. That is why we have provided a combination of standard features and optional extras designed to deter and prevent thieves from stealing your property. And in the unlikely event that they should succeed, aid the identification, speedy recovery of your property and assist in the prosecution of the thief. Caravan Theft The theft of a caravan can occur in the most unlikely circumstances; from a motorway service area, even from an owner s driveway. Secure all windows and doors when your caravan is unoccupied, even if only for a short length of time. ANTI-WIND CORNER STEADIES CRIS - THE CARAVAN REGISTRATION AND IDENTIFICATION SCHEME - VIN CriS is the national register of UK manufactured touring caravans and was established by the National Caravan Council (NCC) in conjunction with HPI Ltd. All Compass caravans are recorded on the CriS database by their unique 17 digit Vehicle Identity Number (VIN). This VIN and the caravan description are recorded on the Touring Caravan Registration Document, which is sent by CriS to the caravan s registered keeper. Make a separate note of the number to keep safe at home. CriS issues Touring Caravan Registration Documents which are the equivalent of the log books issued by the DVLA for cars - the Touring Caravan Registration Document confirms the name of the registered keeper, the VIN and full vehicle description. Shortly after purchasing this caravan you should receive your Touring Caravan Registration Document. It will be sent by post to your home address. The rear corner steadies on all Compass caravans have a special cowling that allows for the precise positioning of a security bolt. Once the corner steadies are down, the bolt is put in place and padlocked. This prevents the potential thief from being able to lift the corner steadies making it extremely difficult to tow the vehicle away. Owners are advised to purchase good quality, extended loop padlocks in order to secure them. 10-1

56 SECURITY WINDOW ETCHING & CHASSIS MARKING The VIN number is stamped onto the chassis of the touring caravan and etched onto all of the windows acting as a further deterrent. Your Touring Caravan Registration Document will include a 17 character VIN (Vehicle Identification Number), shown in the top right -hand corner. This 17 character VIN will be die- stamped into the caravan drawbar and chemically etched on up to a maximum of 10 eye level windows. To protect yourself and your touring caravan, never leave the Registration Document in the caravan. For security reasons keep it in a safe place. If you sell the caravan please follow the instructions on the Touring Caravan Registration Document. Please Note: If you do not receive a Touring Caravan Registration Document, lose it, or any of the details recorded are incorrect, please contact: CRIS - Dolphin House, New Street, Salisbury, Wiltshire, SP1 2TB. Telephone: Spare windows stencils can be found in your owners information pack for use if you ever need to order a replacement window. ELECTRONIC TAGGING ADDITIONAL SECURITY Consider fitting any device which might deter or prevent intrusion by thieves. For example: A wheel lock will prevent towing of the caravan and removal of the wheel. FREE CRIME PREVENTION advice about securing your caravan, protecting your valuables, property marking, either at home or whilst on site, can be obtained from the Crime Prevention Officer through your local Police Station. In conjunction with the CriS registration scheme, all Compass touring caravans are electronically tagged during manufacture for added security and ease vehicle identification. The security tag containing the individual identity of your caravan is concealed within the caravan body and can only be read by using a special decoder. Please Note: Your Local Police Can Obtain The Use Of A Decoder By Contacting C.R.I.S. on Telephone No

57 CARE OF YOUR CARAVAN CARE OF YOUR CARAVAN This section of the guide is devoted to the care, cleaning and general preservation of your caravan in order to retain its showroom condition. EXTERIOR CLEANING Under no circumstances should an abrasive or harsh cleaner be used. Do not use a pressure wash as this can disturb mastic seals. Exterior painted body parts of the caravan (usually the side walls) are acrylic finished aluminium, which is extremely durable and easy to clean. It is recommended you first wash off any heavy dirt and mud with cold water then use a proprietary brand wash and wax shampoo and rinse with plenty of cold water. Caution: The use of a pressure wash on your caravan is not recommended as it can lead to water entering the caravan via any of the external vents and could disturb the seals. GLASS FIBRE REINFORCED PLASTIC (GRP) GRP components need to be washed, waxed and taken care of like a car. Chemicals and dirt can collect during storage, and the gel coat can be stained or marked when chemicals combine with rain or dew. Most stains or marks can be removed with mild dishwashing detergent, but more stubborn marks may require a (fine grit) rubbing compound such as T-cut. To help keep your GRP components looking almost like new, it is wise to wash the parts monthly (or more frequently) using mild dishwashing detergent, but avoid using strong alkaline (e.g. trisodium phosphate) or acidic cleaners or abrasives. Waxing the components once or twice a year with a good grade paste wax will help to maintain the colour and finish. ACRYLIC WINDOWS Your caravan is fitted with shatter resistant acrylic windows. To preserve their clarity and unblemished transparency it is essential that the following cleaning instructions are strictly adhered to: Road grit, dust, sand, flies, lime tree secretions, bird droppings etc., should be washed off using plenty of cold water do not use a sponge to clean off heavy dirt deposits. Any remaining dirt should be washed off using a soft cloth and warm water. Please Note: Under NO circumstances should any abrasive cleaning agents, household detergents or proprietary cleaning fluids be used. Wash the window again using only cold water and dry off with chamois leather. Please Note: Should scratches appear on the acrylic windows these can often be removed with an acrylic polish, i.e. ICI Perspex polish. Gentle polishing with a liquid metal polish, i.e. Brasso may also have the desired effect - consult your retailer BEFORE attempting to remove any but the slightest scratch. CARE INSTRUCTIONS FOR SEITZ WINDOWS Use soap suds and plenty of water or Seitz special cleaning agents to wash the acrylic window. Use talcum powder to care for the rubber seals. Only use water and mild soap suds to clean the blinds. Please Note: Do not keep the blinds closed for long periods of time, as this can result in material fatigue. CARE INSTRUCTIONS FOR SEITZ ROOFLIGHTS Clean the acrylic rooflight with soap suds and plenty of water, or use the Seitz special cleaner. Use talcum to care for the rubber seals. Only use water and mild soap suds to clean the blinds. Please Note: The 12-month guarantee becomes null and void if these instructions are not followed. WINDOW BLINDS & FLYSCREENS To clean the blinds and flyscreens, moisten a soft cloth or sponge with a small amount of water and mild soap suds and gently wipe dirt off. Allow to dry before retracting, failure to due this could result in mildew forming. Winterisation/Storage Please Note: The blind/flyscreen should not be left in the down position when the caravan is not in use or throughout the winter as the memory of the mechanism may be lost. 11-1

58 CARE OF YOUR CARAVAN ABS - A FRAME COVER, WHEEL SPATS & PANELS To preserve the appearance of all ABS panels and fittings road grit, dust, sand, flies, lime tree secretions, bird droppings etc., should be washed off using plenty of cold water. Any remaining dirt should be washed off using a soft cloth and warm water. Under NO circumstances should any abrasive cleaning agents, household detergents or proprietary cleaning fluids be used. Wash the ABS material again using only cold water and dry off INTERIOR WALLS Your caravan interior walls will only require a wipe over with a damp cloth, using a mild detergent, to keep them in a showroom condition. FURNITURE Treat your caravan furniture as you would the furniture in your home. Polish wood surfaces sparingly with a good quality wax or spray polish. Use a damp cloth to clean melanate laminated surfaces. COOKING EQUIPMENT Caustic pastes, abrasive cleaning powders, coarse wire wool and hard implements will damage the surface. CARPETS, UPHOLSTERY AND CURTAINS Vacuum clean carpets and upholstery to ensure a long life, marks on cushions can be removed using a mild upholstery shampoo with the minimum of water. Curtains should be dry cleaned only. WARNING: Under no circumstances should alcohol, spirit or solvent-based liquids be used on GRP or ABS plastic panels as these substances may react with the material and cause visible damage. SHOWER TRAYS, SHOWER ROOM AND WASH BASIN FITTINGS Only clean your shower tray using soap and water. Do not use chemical based cleaning agents as this may attack the material of the tray. CLEANING OF ALL TAPS It is recommended that a non-abrasive damp cloth be used for cleaning the taps and showers. WATER CONTAINERS (i) All water remaining in any water container should be disposed of so that the container is empty. (ii) The outside of external water containers should be thoroughly cleansed and washed down to remove any dirt, dust or other contaminant. Water at a suitably hot temperature containing an appropriate detergent is recommended for this purpose. Water should then be put into the container, swirled round, then emptied out. (iii) All containers should then be totally filled with water containing an appropriate disinfectant / sterilizing solution and allowed to stand for the recommended contact time (e.g. Milton for 15 minutes). (iv) The solution should be emptied from the container. (v) The opening of any container should be cleaned thoroughly with an appropriate preprepared wipe impregnated with a disinfectant / sterilizing solution. (vi) External containers should be inverted whilst stored overnight (if possible). (vii) Containers must be filled with mains water only and mains water only should be used for the above cleaning procedure. (viii) On no account should garden hoses be used to fill water tanks. 11-2

59 CARE OF YOUR CARAVAN WATER SYSTEMS - STERILIZATION Clean the water system at the start and end of the season with sterilizing fluid. When cleaning it is advisable to use a sterilizing fluid e.g. Chempro SDP or similar. Please Note: It is recommended that for this operation the filter is removed as the fluid reduces the effectiveness of a new filter. (i) Drain down the system. (Open all taps to allow air in, enabling the system to drain quickly.) See Index - Water System, Draining. (ii) Remove any water filters fitted, and replace with a short length of hose or empty filter cartridge (this will ensure the filter is not affected by the disinfectant / sterilizing solution). (iii) Fill the system by using the pump with a disinfectant / sterilizing solution. (Check that the solution at full strength appears at all taps/showers). Allow to stand for the recommended period of time. (iv) Drain the system down completely. (v) Thoroughly clean the outside of all taps/ connectors with a cloth soaked in the disinfectant / sterilizing solution. (vi) Flush the system through with clean drinking water until no traces of disinfectant / sterilizing solution can be detected at any tap. (vii) After sterilizing the system at the start of the season it is recommended that a new Ultraflow filter cartridge should be fitted. Please Note: Suitable sterilizing chemicals are available from your Explorer Group Retailer, accessory shop, chemists, or home-brew shops. It is not, however, recommended to use bleach or sodium met bisulphide. TRUMA SPACE HEATER Please note: Your Truma Space Heater front is now attached using 2 screws. These screws must be removed prior to removal of the Space Heater front. These screws can be seen when looking into the fire through the air vents. THETFORD TOILET WARNINGS Cold Weather Use - to prevent freezing during cold weather use, add antifreeze to the toilet system fresh water tank. Use a non-toxic (propylene glycol) type of antifreeze. Refer to chart on container to obtain level of protection. Warmer weather or longer intervals between emptying the waste tank may require additional toilet fluid. Use only Thetford toilet fluid to achieve the best results. CAUTIONS Never add toilet fluid directly into toilet bowl. Do not use strong household detergents or cleaners that contain chlorine, solvents or acid contents. High Altitude and Hot Weather Use - with large temperature differences and changing heights during towing, over pressure can start to build up in the waste holding tank, causing contents to splash upward upon opening the valve blade if opened too fast. 11-3

60 CARE OF YOUR CARAVAN CHASSIS MOUNTED SPARE WHEEL CARRIER Each caravan chassis has a set of punched holes immediately behind the axle to enable fitting of a spare wheel carrier. To gain access to your spare wheel lift the spare wheel carrier up and lift up the locking mechanism. Then move the mechanism to the horizontal position and the spare wheel carrier will be free to move over the mechanism and allow the spare wheel to drop to the floor to be removed. To replace the spare wheel simply reverse the operation making sure that the quick release mechanism has been fully pushed down to create a positive lock. The carrier is of extra strong, lightweight construction and zinc plated for all weather protection. It is easy to fit and accepts all conventional wheel sizes. TYRES Please refer to Section 18 Technical Specifications which is contained within this handbook for information regarding tyre pressures and axle loads. Pressures It is customary for manufacturers to mark tyres with load and inflation data. This information relates to the use of the tyre on cars. It is dangerous to drive with under inflated tyres. The pressures (cold) recommended by the manufacturers should be regarded as a minimum. Pressure checks, including those on the spare tyre, should be made with the tyres cold and using an accurate pressure gauge. The checks should be carried out before each journey and at regular intervals during storage. Tyre Wear and Damage The legal requirements for tread depth on motor vehicle tyres apply also to caravans. Similarly, it is not permitted to mix cross-ply and radial tyres on the same axle. A redundant tyre must be replaced by one of the same size and construction. Wheels should be balanced and changed round occasionally to equal wear and prolong the life of the tyres. A tyre should be renewed if a blister, rupture or cut exposing the casing is detected. If the tyre has suffered a violent impact e.g. against a kerb, it should be examined by a specialist as soon as possible. Please Note: It is customary for tyre manufacturers to mark tyres with load and inflation data. It is important to understand that this information relates only to the use of tyres on cars. CHANGING A WHEEL Whenever road wheels are removed and refitted, they must be tightened using a calibrated Torque Wrench set to 92 Nm for steel wheels and 115Nm for alloy wheels. Only use the wheel bolts supplied with your caravan. If you need to replace these bolts you should obtain bolts from an approved Compass Retailer. The bolt fixings should be tightened in the sequence shown in the diagram below. Do NOT simply tighten clockwise or anti clockwise. Remember to over tighten is just as dangerous as to under-tighten, as this can distort the wheel rims. Avoid the use of power wrenches. Wheel bolts should NEVER be lubricated. 11-4

61 CARE OF YOUR CARAVAN The corner steadies must not be used to jack up the caravan. They can be lowered to touch the ground only as a safety measure to stabilise the caravan. (i) Apply the handbrake fully as for parking. Do not forget to give the caravan a slight rearwards push to stop the reversing lever collapsing. (ii) Slacken off the wheel bolts on the wheel to be changed. (iii) With a suitable jack, jack up the caravan under either the axle tube or the axle mounting plate. Please Note: Do Not Use The Chassis As A Jacking Point. If there is lack of ground clearance because of a flat tyre, gently move the caravan onto some ramping boards. (iv) Support the weight of the caravan with the jack and for added safety lower the front and rear corner steadies on the side of the flat tyre. Then remove the ramping boards. (v) Remove the wheel bolts and remove the wheel. (vi) Before fitting the wheel, examine it for distortion or other damage. Ensure that all mating surfaces are clean and dry, including bolt/nut seats. Please Note: Always Use the Correct Bolts to Secure the Wheel - Check with the dealer if unsure. Please Note: A corner steady brace is not to be used for the next step. (vii) Insert the wheel locating pins (supplied within your Compass kit box) into holes 4 and 5 and then slide the wheel onto the locating pins. (viii) Insert the wheels bolts into holes 1 then 2 and then 3. (ix) Remove the wheel locating pins from holes 4 and 5 and insert the wheel bolts. (x) After the bolts have been screwed in as far as possible by hand, each bolt should be tightened gradually in sequence. Do not over tighten at this point as the final tightening should be done with a calibrated torque wrench. The wheels of the caravan will not rotate during tightening as they are held rigid by the wheel hub brake unit. (xi) Raise the corner steadies. (xii) Lower the caravan to the ground. (xiii) The wheel bolts should be tightened ensuring that the torque is applied evenly around the wheel. Using a suitable torque wrench, sequentially tighten the steel bolts to a torque of 92Nm for steel wheels and 115Nm for alloy wheels following the sequence stated above. IMPORTANT The torque settings should be rechecked after 50 km (20 miles) and every 5000 km (3100 miles) thereafter. Do not loosen the wheel bolts to carry out this operation whilst the road wheel is supporting the weight of the caravan. Wheel bolts should NEVER be lubricated. NB: If you upgrade from steel to alloy wheels you must ensure you use the correct bolts for the new wheel. JACKING Under no circumstances should the corner steadies be used to jack up the caravan. When it is necessary to jack up, use a bottle, screw, trolley or scissor type jack, one with an axle shaped head is recommended. Place the jack plate under the axle tube as near as possible to the main longitudinal member. The maximum mass which the jockey wheel and its clamping mechanism are capable of withstanding is 150kgs. LUBRICATION Lubricate the Jockey Wheel Lightly oil the wheel axle and screw thread. Lubricate the Brake Linkage Lightly oil all moving parts. Lubricate the Corner Steadies Lightly oil the screw and pivot pins. 11-5

62 CARE OF YOUR CARAVAN MAINTENANCE OF YOUR BPW CHASSIS CATEGORY OF EXPOSURE & DURATION OF PROTECTION The BPW chassis is protected by a hot dip galvanising process in accordance to DIN EN ISO The duration of protection is according to a salt spray test to DIN standard. WARNING: Holes must not be made without approval of the chassis manufacturer. The following maintenance instructions relate to the BPW chassis fitted to your Compass caravan. They are a constituent part of the warranty conditions. Adhere to the relevant operating instructions of the vehicle manufacturer or of the other vehicle component manufacturers. Completion of the maintenance work in accordance with the prescribed intervals is essential in order to maintain the operating safety and roadworthiness of the vehicle. The correction of any defects found or the replacement of any worn parts should be carried out by a BPW after sales service workshop, unless the vehicle user has at his disposal appropriately skilled in company workers and the necessary technical facilities. Please Note: When installing spare parts, it is strongly recommended that only original BPW components are used. Parts approved by BPW for caravan axles and suspensions regularly undergo special test procedures and as a result BPW is able to guarantee their quality. However, BPW cannot assess for every single third party product whether it can be used for BPW caravan axles and suspensions without any risk to safety. This applies even if an accredited test authority has already tested such products. Our warranty becomes null and void if spare parts other than original BPW parts are used. Procurement of Spare Parts The code and type numbers of the axle and chassis components enable us to quickly determine your exact spares requirements when ordering from our BPW agencies and service stations. It is therefore recommended that you enter the data shown on the type plate in the following table so that it is readily available when required. The type plate or the imprint is located on the axle tube or on the housing of the towing equipment and couplings. Please Note: For full maintenance details of the BPW chassis, undergear and Winterhoff coupling please refer to the individual manufacturer s handbook supplied within your user information pack. 11-6

63 STORAGE STORAGE LONG TERM & WINTER STORAGE If the caravan is to be stored for any length of time, especially over the winter period, the following operations are recommended: (i) Remove all linens, blankets, cushions, clothes, mattresses, etc, that could be affected by damp conditions. (ii) Clean the caravan inside and out as detailed in the previous section. (iii) Drain the water system (see Water system). (iv) For winter storage and to prevent frost damage all taps must be left in open position. For those caravans with lift up taps please ensure the taps are left in the central position. (v) Ensure all windows, roof lights and doors are correctly fastened. Check fixed ventilation apertures are not obstructed. (vi) Ensure that the refrigerator/freezer compartment doors are secured in the vent position using the door catch. (vii) Check that the site you have chosen to store the caravan is open, fairly high and dry and if possible not exposed to gales etc. If this proves impossible it is recommended that the caravan chassis is anchored to the ground. (viii) Jack up the caravan (use bottle or screw jack, do NOT use the corner steadies) so that the wheels are clear of the ground. (ix) Support the caravan axle with wooden blocks, axle stands or similar so that when the jacks are removed the wheels remain clear of the ground. Lower the corner steadies to just site the caravan. Cover the tyres to prevent deterioration. Release the handbrake. (x) Security: Lowering and locking the corner steadies and removing the wheels will reduce the risk of caravan theft. CARAVAN COVERS Caravan covers may be used to protect your new Compass caravan provided that the cover used is of a breathable type. Ensure that the point of extending aerials or the status aerial (depending on model if fitted) are removed or retracted, and that the cover is well tied down to avoid the cover being punctured. Your caravan must be ventilated every 4 to 6 weeks if it is to be stored with a cover in place. POWER DRAIN In order to reduce any drain on your leisure battery while your caravan is being stored ensure that the main control switch on the refrigerator is set to the 0 position Please Note: Do not work under the caravan unless the corner steadies are down and the axle is supported. Should the caravan be stored for a prolonged period of time it is strongly recommended that the caravan is fully serviced before the commencement of use. Your retailer will ensure that your caravan is safe, secure and ready for your enjoyment. Please Note: Caravans stored for any length of time should not have the handbrake or brakes applied. The wheels should be chocked or wedged and the handbrake released. The hitch head should be checked to see that it is fully extended and that there is no load on the braking system. 12-1

64 STORAGE 12-2

65 WARRANTY WARRANTY 3-YEAR MANUFACTURER S WARRANTY Subject to the following conditions, your caravan is supplied with a manufacturer s warranty for 3 years from the original date of purchase, at no additional cost to you the customer. We sincerely hope you will never have cause to complain about your caravan. However, if you do have a problem then please contact your Retailer so they can report this through our warranty system. We are confident they will do their utmost to resolve any problems to your complete satisfaction. The Retailer from whom the caravan is purchased is liable for warranty repairs. Any other approved Retailer or Service Centre may carry out work at his own convenience and/or discretion, but is not obliged to do so. PARTS COVERED BY THIS WARRANTY FOR YEARS 1-3 Subject to the specific exclusions in years 2 and 3 set out below all original components of the caravan, including permanently fitted equipment, forming part of the manufacturer s original specification. SPECIFIC EXCLUSIONS FOR YEARS 2 & 3 Microwave, tyres, batteries, plastic windows, glass, exterior paint work, bright work and all similar trim and finish, soft furnishings, carpets and floor coverings. Entertainment/communication systems and connected equipment. Adjustment of blinds, hinges, catches, stays and doors. Replacement bulbs, fluorescent tubes, fuses and electrical connections, locks; GRP, ABS and PVC products including A-frame covers, wheel spats and shower trays. Natural movement of internal doors and furniture. Normal wear and tear/ servicing items and other components subject to routine maintenance. CONDITIONS ATTACHED TO THE WARRANTY: Failure to comply with the following conditions may invalidate your Warranty. (i) The duration of the warranty is 36 months from the original date of purchase. (ii) That the original construction of the caravan has not been tampered with or repaired other than by Explorer Group or an approved Retailer or Service Centre. (iii) That an annual service, damp and safety check has been carried out by an approved Retailer or Service Centre. The first and second services are due 60 days either side of the anniversary of the original date of purchase. The interval between services must not exceed 14 months. The third service must be on or before the anniversary date of the original purchase. (iv) That original VAT service invoices are retained as proof that annual service and inspections have been carried out. (v) No work should be commenced under the terms of the warranty unless prior authorization is obtained from The Explorer Group. (vi) Explorer Group reserves the right to inspect the caravan before any work commences. (vii) No liability will be accepted for damage caused by fair wear and tear, wilful damage, negligence, abnormal working conditions, intrusion of foreign or harmful matter, overheating, freezing, failure to follow The Explorer Group instructions, misuse or alteration or repair of the caravan without The Explorer Group prior approval. (viii) Caravans covered by this warranty shall not be put out to hire, reward, or any other commercial use or used in any timed race. (ix) That the caravan shall be used only for its ordinary and intended purpose and shall not be subjected to any condition which could reasonably be foreseen to cause or result in damage or excessive wear and tear. (x) That only private cars or 4x4 type vehicles substituting as private cars, shall have towed the caravan. (xi) That no liability arises from this warranty for transport costs to and from the place of remedial work or consequential cost relating to transportation. No liability arises out of this warranty for any indirect, special or consequential loss or damage (whether for loss of profit, use, contract, goodwill, or 13-1

66 WARRANTY otherwise), costs, expenses or other claims for compensation howsoever arising. (xii) No liability will be accepted for any accidental or fire damage or any loss incurred by accident or fire. (xiii) The unexpired period of the 3-year warranty or the 5 year water ingress is transferable to second and subsequent owners during the warranty period. The new owner should contact Explorer Group within 3 months of their purchase, with proof of ownership, service history and their payment of 30 to have their details recorded in our database. Please Note: This warranty does not affect the purchaser s statutory rights. This warranty shall be governed and construed in accordance with the laws of England and the parties irrevocably submit to the exclusive jurisdiction of the courts of England. 13-2

67 CODE OF PRACTICE - WATER INGRESS CODE OF PRACTICE - WATER INGRESS At Compass we want our customers to be sure that, in buying one of our caravans, you are buying the very best. We would like you to continue to believe this for a long time after you have made your purchase. We are confident that our new caravans, built with innovative manufacturing techniques and tested materials, make water ingress concerns unnecessary. We are so confident of our new caravans that we follow a Code of Practice which gives certain guarantees to our customers, both consumers and Retailers, of financial reimbursement for remedial work costs should problems occur. THE CODE The code applies to all new Compass Group products manufactured after 1st September All owners with documentary proof of annual services by an approved Compass Group Retailer or Service Centre will be paid in full for the costs of remedial work due to water ingress. This is valid for up to 5 years from the original date of purchase of a new product. Unless the caravan has a full service history, the owner will be required to contribute to the costs of remedial work for water ingress damage depending upon the age of the caravan and work required. Each case will be examined on its own merit. Explorer will decide the amount of contribution towards the remedial work costs. Owners exchanging their current Explorer Group model for a new Compass Group model will not have the value of their part exchange reduced due to potential water ingress issues, providing that there is documentary evidence that the caravan has been annually serviced and that it is less than 5 years old. CONDITIONS ATTACHED TO THE CODE (i) Work may only be undertaken after approval by Compass (depending upon individual circumstances). (ii) Compass will pay the costs of remedial work, only after approved work has been carried out. (iii) The Code is not retrospective. Caravans traded-in prior to implementation of the Code are not covered. CUSTOMER OBLIGATION - SERVICING It is a condition of your warranty that your caravan must have an annual service, damp and safety check and this should be carried out by a Compass Group approved Retailer or Service Centre, in accordance with NCC guidelines. Proof of this will be required in the event of a warranty claim. Please Note: Failure to do so will invalidate your warranty. The first service is due 60 days either side of the anniversary of the original date of purchase. The interval from purchase date to the first service and the intervals between services must not exceed 14 months. Years 3 and 5 must be on or before the anniversary date of the original purchase. Your caravan requires servicing for safety, efficiency and to protect the investment you have made. Whether the caravan is used for short trips or continental long range touring, regular servicing is necessary and will ensure continued enjoyment of your caravan. Your Retailer or Service Centre will carry out your service using the latest techniques and equipment (a list of the items to be inspected, tested and adjusted appears on the Service Vouchers in this handbook), and should provide you with the service document as proof of regular maintenance. As with motor vehicle service documents, not only will the proof of regular servicing enhance your caravan resale value, but in the unlikely event of any defect appearing at some later date - a properly serviced and documented caravan history will enable your Retailer to rapidly assess and where appropriate, carry out the necessary remedial work. MAINS ELECTRICS It is recommended that you have your Mains Electrics System inspected by an NICEIC approved contractor every 3 years. SPARE PARTS Should you require any replacement parts for your caravan it is necessary that you contact the Retailer from whom you purchased the caravan or any Compass Group approved Retailer and give the following information, which will help in 14-1

68 CODE OF PRACTICE - WATER INGRESS identifying the required component: (i) Model and make of caravan (ii) VIN number (iii) Description of required part (iv) Photograph, size or diagram of required part Please Note: All parts must be ordered and supplied through an approved retailer. REMEDIAL WORK The Compass Group together with its suppliers is continually undertaking extensive research into testing, remedial work procedures and materials such as sealants, adhesives, gaskets and tapes. Therefore, if for any reason your new caravan is damaged or requires remedial work then only an approved Compass Group Retailer or Service Centre should undertake such work. All such work should be undertaken using only approved Compass Group genuine parts, recommended sealant and following Compass Group procedures. Compass will also undertake to supply certain specialist repairers with the necessary spare parts. In this case, your selected repairer must contact the PARTS DEPARTMENT with all enquiries. 14-2

69 CARAVAN CONSTRUCTION CARAVAN CONSTRUCTION - MAIN COMPONENTS The following is a brief description of the main components used in your caravan. More comprehensive descriptions can be found in the equipment manufacturers literature held in the Owner s Information Pack. BPW CHASSIS BPW are one of the largest producers of caravan chassis in Europe. The chassis is galvanized special steel fitted with neidhart axles and suspension system. Compass utilizes the new BPW V-TEC Chassis System. BRAKING SYSTEM The Braking System comprises a rod operated overrunning device with expander mechanism and adjuster box. An automatic reversing system with a spring loaded reverse lever is attached to the adjuster box. The system also incorporates a link device, which gives added safety to the handbrake operation when parking on a reverse slope or steep hill. Brake adjustment instructions are given in the maintenance section of this guide. BODY SHELL Caravan bodies are constructed from the highest quality materials. The fully insulated floor is constructed from a timber frame with plywood and insulation laminated together for strength. The walls comprise an insulated foam sandwich having pre-coated aluminium exterior surface and vinyl coated plywood interior finish. Wooden framing is positioned within the sandwich to add strength. The very latest state of the art presses are employed to produce the extremely well insulated, robust, yet lightweight sections. FRONT PANEL AND GAS BOTTLE LOCKER LID These are constructed from moulded GRP for strength and lightness. AWNING CHANNEL Each caravan is fitted, as standard, with an awning channel as an integral part of the near- and/or offside aluminium roof and body side moulding. If it is found necessary to fit additional attachments, care must be taken to ensure that any holes which are drilled in the outside of the body are correctly sealed. Awnings which employ rubber sucker attachments rather than screw fixings are recommended. ADDITIONAL FIXINGS TO YOUR CARAVAN SHELL On NO account should screw threads longer than 5/8th inch (15mm) be permitted to enter the shell sandwich (from inside). Ensure that all screws are of the self tapping type. No screw or any other object should be permitted to enter the ceiling of your new caravan. Please Note: Holes must not be drilled into the chassis. When purchasing a stabilizer, consult your retailer who will advise on the correct type to fit. WINDOWS Windows are all of a double glazed acrylic construction and the door frames are extruded aluminium. INSULATION Compass caravans are built to thermal insulation Grade 2. This states that an average temperature difference of at least 20K between inside and outside temperatures should be achieved when the outside temperature is 0ºC. 15-1

70 CARAVAN CONSTRUCTION 15-2

71 EQUIPMENT LIST EQUIPMENT LIST OMEGA REFRIGERATOR HEATER INTERNAL BLOWN AIR WATER HEATER SINK AND DRAINER OVEN MICROWAVE HOB TAPS KITCHEN SHOWER EQUIPMENT TAPS VANITY WATER FILTER / PUMP LIGHTS 12V FLUORESCENT LIGHTS 12V DOWN LIGHTS LIGHTS 230V MAINS LIGHTS 12V HALOGEN CONTROL PANELS ELECTRICAL FITTINGS TOILET DOMETIC RM7651 FRIDGE FREEZER THETFORD N112 LCD TRUMA ULTRAHEAT AUTO TRUMA PUSH FIT RAPID INSTALLATION TRUMA ULTRASTORE ARGENT STAINLESS STEEL SPINFLO MIDI PRIMA WITH ILLUMINATION & 2 SHELFS BCA DIGITAL 700 W CW SURROUND SPINFLO 3 BURNER HOB DIMATEC SINGLE LEVER MIXER DIMATEC MIXER DIMATEC SINGLE LEVER MIXER WHALE COMPLETE SYSTEM LUMO & CROWN ICE ZOE EYEBALL HALOGEN BCA NOVA CBE CBE THETFORD ROTATABLE WITH ELECTRONIC FLUSH CASSETTE BLINDS SEITZ SERIES

72 EQUIPMENT LIST 16-2

73 ELECTRICAL DRAWINGS ELECTRICAL DRAWINGS 13 PIN PLUG WIRING DIAGRAM 17-1