RP-series slicer M251CE/M301CE/M351CE

Transcription

1 RP-series slicer M251CE/M301CE/M351CE Service Instructions ENGLISH issue

2 2.1 Safety

3 Contents Table of Contents: 1 Introduction 2 Safety 3 Operation 4 Installation 5 Electrical Drawings 6 Technical Information 7 Appendices Service Instructions RP-M251CE/RP-M301CE/RP-M351CE i

4 2.1 Safety ii Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

5 Section 1 Introduction Table of Contents: page no 1.1 General 1-3 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 1-1

6 1 Introduction 1-2 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

7 1 Introduction 1.1 General The Avery Berkel slicing machine and its accessories are manufactured in accordance with the EEC 89/392 Machinery Directive and further modifications. They meet all legislative requirements valid at the date of manufacture. Its principle characteristics are easy cleaning, robust manufacture, safe and reliable operation. The materials utilised, anodised aluminium, stainless steel and plastics have been selected with due regard to hygiene regulations, and ensure that the machine has a long life. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 1-3

8 1 Introduction 1-4 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

9 Section 2 Safety Table of Contents: page no 2.1 Electrical safety devices Mechanical safety devices 2-4 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 2-1

10 2 Safety 2-2 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

11 2 Safety 2.1 Electrical safety devices The electrical safety devices in accordance with the EN standards are: Note: Start and stop pushbuttons. Control circuit provided with electric servo-control; in the case of blade clamping the machine must be restarted manually. Device to stop the rotation of the blade if the clamping handle of the blade guard is released. When the machine is not used: Make sure that it is off. Re-position the slice thickness control to zero. Do not remove the labels placed on the machine. Only replace them if damaged. V 230 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 2-3

12 2 Safety 2.2 Mechanical safety devices The slicer is manufactured according to EEC 89/392 Machinery Directive and further modifications. The mechanical safety devices are: Product holder removable only with the slice thickness control on 0 (slice thickness plate positioned to protect the blade). After removing the product holder the slice thickness plate is mechanically clamped. Protection devices mounted on the product holder to prevent the operator from any accidental contact with the blade. Blade guard. This fixed ring protects that part of the blade which is not used for the cutting operation. A special mechanical safety device which permits sharpening of the blade, keeping the fingers of the operator away from the cutting edge of the blade. 2-4 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

13 Section 3 Operation Table of Contents: page no 3.1 RP-M251CE/M301CE Definitions Technical specification Slicer operation and use Cleaning and operator removable parts Sharpening Lubrication RP-M351CE Definitions Technical specification Slicer functioning and use Cleaning and operator removable parts Sharpening Lubrication 3-30 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-1

14 3 Operation 3-2 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

15 3 Operation 3.1 RP-M251CE/M301CE Definitions 1. Control pushbuttons 2. Slice thickness control Carriage 4. Product holder clamping handle 5. Product holder Product holder pushing handle 6 7. Last slice device 8. Pusher 9. Carriage bar oiler Blade 11. Blade cover 12. Blade guard Slice thickness plate 14. Slice deflector 15. Slice receiving tray 16. Blade cover fastener handle Blade sharpener cover Integrated blade sharpener Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-3

16 3 Operation Technical specification 1. Blade Ø mm 2. Slicing capacity 3. Dimensions mm 4. Weight Kg a. without packaging b. with packaging 5. Range temperature +5C - +40C 6. Slice thickness control 0-14 mm 7. Blade 300 rev/min 8. Acoustic <70 db 9. Protection of the electrical system and switches grade IP Cutting zone RP-M251CE RP-301CE A B C D E 460 F 330 G 580 H 420 I a. 24 b. 29 Motors: electrical data Nominal W Max. Connection Phase N o. Cos ϕ n min V Hz A CL A VL F IP Service Degree of Protection ~ 0,8 0, B S Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

17 3 Operation Slicer operation and use The following products can be sliced: sausages, ham, cheese, bread. If large quantities of bread or cheese are usually cut, a teflon coating is recommended. (Optional accessory 97). Note: The following must not be sliced: non-edible products. foodstuffs with bones. frozen products. How to load the product to be cut 1. Check that the slicer is switched off and set the slice thickness control to zero. 2. Pull the product holder towards the operator. 3. Lift and rotate the last slice device outwards Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-5

18 3 Operation 4. Place the product to be cut against the wall of the product holder and the slice thickness plate. 5. Place the last slice device on the product to be cut in a position away from the slice thickness plate. The product is fed by gravity to the slice thickness plate making cutting easier. 6. Set the slice thickness control to the thickness desired. 7. Press switch to switch on the machine. 8. Push the product holder at a steady speed towards the blade end then pull it back towards the operator, and repeat the operation. 9. After cutting the product, leave the product holder in position back towards the operator end. 10. Press pushbutton to stop; re-set the slice thickness control to zero, and remove the product. 3-6 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

19 3 Operation How to load short goods for cutting (last slice) WARNING: DO NOT USE YOUR HANDS TO PUSH THE GOODS TOWARDS THE BLADE. FOLLOW THESE INSTRUCTIONS WITH GREAT CARE. 1. Check that the slice thickness control is set on zero and the slicer is switched off. 2. Pull the product holder towards the operator. 3. Lift and rotate the last slice device outwards. 4. Place the product to be cut against the wall of the product holder and the slice thickness plate. 5. Push the goods against the slice thickness plate using the last slice device. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-7

20 3 Operation 6. Set the slice thickness control to the required thickness. 7. Press pushbutton to start the machine. 8. Hold the handle of the last slice device. Apply a light pressure on the goods towards the slice thickness plate and push the product holder to the end of the blade stroke; then pull it back to the operator and repeat the operation. 9. After cutting the product, move the product holder back towards the operator. 10. Press pushbutton to stop. Reset the slice thickness control to zero, and remove the product. Sharpening If the product is not cut frequently, the blade must be sharpened following the instructions indicated in Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

21 3 Operation Cleaning The machine must be cleaned once a day or more frequently if necessary. Clean all the parts using a cloth moistened with water and washing up liquid, and a brush (do not use strong detergents). WARNING: DO NOT USE A WATER JET. DANGER: PERFORM THE CLEANING OPERATIONS WITH GREAT CARE: DANGER OF INJURY. Component removal Product holder 1. Rotate the product holder clamping handle counterclockwise. 2. Set the slice thickness control to zero. 3. Pull the carriage to the operator end of its travel. A click will inform the operator that the product holder is clamped. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-9

22 3 Operation 4. Remove the last slice device from the guide bar. 5. Lift the product holder from the carriage. The slice thickness control remains clamped on zero. Note: The slicer thickness control is clamped on zero. Slice deflector 1. Loosen the fixing screw and remove the slice deflector. Blade cover 1. Loosen the blade cover fastening handle by rotating it counterclockwise. 2. Lift the blade cover from the blade by pushing on the handle in the direction indicated by the arrow. Note: Once removed from the blade cover, an interlocking device stops the rotation of the blade Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

23 3 Operation Blade cleaning 1. Lift the blade cover. DANGER: TAKE CARE TO AVOID ANY ACCIDENTAL CONTACT WITH THE BLADE WHILE CLEANING IT. 2. Press a damp cloth on the front side of the blade and move slowly from the centre towards the edge in the direction of the arrow. 3. Follow these instructions to clean the other side of the blade. 4. Dry both sides of the blade with a cloth in the same way. 5. Insert a damp cloth between the blade and the protection ring. Pull it outwards and move it to and fro to clean the inside of the protection ring. 6. After cleaning re-place the blade cover; insert the fastener and screw it clockwise to clamp the blade cover. Lower the sharpener protective cover. IMPORTANT: Leave all the parts to soak in warm water and washing-up liquid (do not use strong detergents) and clean them by using a brush or a cloth. Rinse them in warm water and dry them. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-11

24 3 Operation To assemble the machine follow the reverse of the procedure for disassembly Blade sharpening If the cut is unsatisfactory, the blade must be sharpened. The intervals between the sharpening operations depend on the use of the slicer and the kind of products being cut. This operation must be carried out by qualified personnel. The blade must be replaced when its diameter is 10 mm less than that of a new one. WARNING: THE REPLACEMENT OF THE BLADE IS A DANGEROUS OPERATION. IF THE SHARPENING QUALITY IS NOT SATISFACTORY, REPLACE THE STONES. CONTACT CUSTOMER SERVICE AT AVERY-BERKEL. WARNING: SLICERS FITTED WITH A TOOTHED KNIFE (OPTION) ARE ONLY SUITABLE FOR CUTTING BREAD. THE KNIFE SHARPENING MUST BE DONE ONLY BY A TECHNICAL ASSISTANCE CENTRE Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

25 3 Operation The sharpening operation Wear protective gloves Follow the instructions below for correct blade sharpening: 1. Clean the blade and remove any greasy residue. 2. Make sure that the machine is switched off. 3. Set the slice thickness control at zero to make sure that the blade is covered by the slice thickness plate. WARNING: DURING THE FOLLOWING OPERATIONS THE BLADE MUST ALWAYS BE COVERED BY THE REMOVABLE PROTECTION. 4. Lift the sharpener cover. 5. Pull the sharpener release lever and rotate it towards the blade. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-13

26 3 Operation 6. Release the lever; the blade sharpener will be correctly located. 7. Push pushbutton to start the machine. Note: The sharpening operation will take seconds. STOP 8. Sharpening: rotate the handle to bring the two grinding wheels on to the blade. The blade will be sharpened and burred simultaneously. 9. After sharpening press the stop pushbutton Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

27 3 Operation 10. Pull the lever to restore the sharpener to its initial position. 11. Lower the sharpener cover. Cleaning the grinding wheels For satisfactory sharpening the grinding wheel must always be clean. Remove dirt and grease with alcohol and the special brush supplied. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-15

28 3 Operation Guides lubrication This operation must be carried out after cleaning the slicer or whenever the sliding action is difficult. Use Berkel slicer oil. Lubrication of the guide bar for the last slice device 1. Drop some oil on the bar. 2. Slide the last slice device along the guide bar. Lubrication of the guide bar for the product holder carriage 1. Push the product holder towards the operator. 2. Pour lubricating oil into the special carriage bar lubricator. 3. Push the product holder to and fro and repeat the operation. Leave it in a position at the end nearest to the operator Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

29 3 Operation 3.2 RP-M351CE Definitions 1. Control pushbuttons 2. Slice thickness control 3. Carriage 4. Product holder clamping handle Product holder 6. Product holder pushing handle 6 7. Last slice device 8. Pusher 9. Carriage bar oiler 10. Blade 11. Blade cover Blade guard 13. Slice thickness plate 14. Slice deflector 15. Slice receiving tray 16. Blade cover fastener handle Blade sharpener cover 18. Self-contained blade sharpener Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-17

30 3 Operation Technical data 1. Blade Ø mm 2. Slicing capacity 3. Dimensions mm 4. Weight Kg a. without packaging b. with packaging 5. Range temperature +5C - +40C 6. Slice thickness control 0-14 mm 7. Blade 200 rev/min 8. Acoustic <70 db 9. Protection of the electrical system and switches grade IP Cutting zone RP-M351CE A 190 B 260 C 280 D E 540 F 420 G 650 H 540 I 740 L a. 39 b. 48 Motors: electrical data Nominal W Max. Connection Phase N o. Cos ϕ n min V Hz A CL A VL F IP Service Degree of Protection ~ 0, B S Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

31 3 Operation Slicer operation and use The following products can be sliced: sausages, ham, cheese, bread. If large quantities of bread or cheese are usually cut a teflon coating is recommended (Optional accessory 97). Note: The following cannot be sliced: non-edible products. foodstuffs with bones. frozen products. How to load the product to be cut 1. Check that the slicer is switched off and set the slice thickness control to zero. 2. Push the product holder towards the operator. 3. Lift and rotate the last slice device. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-19

32 3 Operation 4. Place the product to be cut against the wall of the product holder and the slice thickness plate. 5. Place the last slice device on to the product to be cut in a position away from the slice thickness plate. The product is fed to the slice thickness plate by gravity to make the cut easier. 6. Set the slice thickness control to the required thickness. 7. Press switch to switch on the machine. 8. Push the product holder at a steady speed to the end of the blade, then pull it back towards the operator and repeat the operation. 9. After cutting the product, pull the product holder back towards the operator. 10. Press pushbutton to stop; reset the slice thickness control to zero, and remove the product Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

33 3 Operation How to load short goods for cutting (last slice) WARNING: DO NOT USE YOUR HANDS TO PUSH THE GOODS TOWARDS THE BLADE. FOLLOW THESE INSTRUCTIONS WITH GREAT CARE. 1. Check that the slice thickness control is set on zero and the slicer is switched off. 2. Pull the product holder towards the operator. 3. Lift and rotate the last slice device outwards. 4. Place the product to be cut against the wall of the product holder and the slice thickness plate. 5. Push the goods against the slice thickness plate using the last slice device. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-21

34 3 Operation 6. Set the slice thickness control to the required thickness. 7. Press pushbutton to start the machine. 8. Hold the handle of the last slice device. Apply a light pressure on the goods towards the slice thickness plate and push the product holder to the end of the blade; then pull it back towards the operator and repeat the operation. 9. After cutting the product, pull the product holder back towards the operator. 10. Press pushbutton to stop; reset the slice thickness control to zero and remove the product. Sharpening If product is not cut frequently the blade must be sharpened. Follow the instructions indicated in Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

35 3 Operation Cleaning The machine must be cleaned once a day or more frequently if necessary. Clean all the parts using a cloth moistened with water and washing up liquid, and a brush (do not use strong detergents). WARNING: DO NOT USE A WATER JET. DANGER: CARRY OUT THE CLEANING OPERATIONS WITH GREAT CARE: DANGER OF INJURY Component removal Product holder 1. Loosen the product holder by rotating the product holder clamping handle counterclockwise. 2. Set the slice thickness control to zero. 3. Pull the product holder towards the operator until it clicks. The click will inform the operator that the product holder is clamped. 4. Lift the last slice device from the guide bar. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-23

36 3 Operation 5. Lift the product holder from the carriage. Note: The slice thickness control remains clamped on zero. Slice deflector 1. Rotate the slice deflector and keep it away from the blade. Blade cover 1. Loosen the blade cover fastening handle by rotating it counterclockwise. 2. Push on the handle in the direction indicated by the arrow to lift the blade cover from the blade. Blade cleaning 1. Lift the blade cover. Note: When the blade cover is removed an interlocking device prevents blade rotation. DANGER: DURING BLADE CLEANING OPERATIONS, TAKE CARE TO AVOID ACCIDENTAL CONTACT WITH IT. 2. Press a damp cloth on the front side of the blade and move slowly from the center towards the edge in the direction of the arrow. 3. Follow these instructions to clean the other side of the blade. 4. Dry both sides of the blade with a cloth in the same way Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

37 3 Operation 5. Insert a damp cloth between the blade and the protection ring. Pull it outwards and move it to and fro to clean the inside of the protection ring. 6. After cleaning replace the blade cover, insert the fastener and screw it clockwise to clamp the blade cover. 7. Lower the sharpener protective cover. IMPORTANT: Leave all the parts to soak in warm water and washing-up liquid (do not use strong detergents) and clean them by using a brush or a cloth. Rinse them in warm water and dry them. To assemble the machine follow the reverse of the disassembly procedure. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-25

38 3 Operation Blade sharpening If the cut is not satisfactory, the blade must be sharpened. The intervals between the sharpening operations depend on the use of the slicer and the kind of products cut. This operation must be carried out only by qualified personnel. The blade must be replaced when its diameter is 10 mm less than that of a new one. WARNING: CONTACT CUSTOMER SERVICES AT AVERY BERKEL FOR BLADE REPLACEMENT. WARNING: THE SLICERS FITTED WITH A TOOTHED KNIFE (OPTION) ARE SUITABLE ONLY FOR CUTTING BREAD. KNIFE SHARPENING MUST BE DONE AT A TECHNICAL ASSISTANCE CENTRE. WARNING: IF THE SHARPNESS IS NOT SATISFACTORY BOTH GRINDING WHEELS IN THE BLADE SHARPENER MUST BE REPLACED. ONLY QUALIFIED PERSONNEL SHOULD REPLACE THEM Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

39 3 Operation Sharpening operation Wear protective gloves For a correct blade sharpening, follow the instructions below: 1. Clean the blade and remove any greasy residue, as in Make sure that the machine is switched off. 3. Set the slice thickness control to zero to ensure that the blade is shielded by the slice thickness plate. WARNING: DURING THE FOLLOWING OPERATIONS THE BLADE MUST ALWAYS BE SHIELDED BY THE REMOVABLE PROTECTION. 4. Lift the sharpener cover. 5. Pull the sharpener release handle. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-27

40 3 Operation 6. Rotate the sharpener assembly to stand over the blade. 7. The blade sharpener is now correctly fixed. 8. Push pushbutton to start the machine. Note: The sharpening operation will take seconds. STOP 9. Sharpening: rotate the lever and bring the two grinding wheels on to the blade. The blades are simultaneously sharpened and burred. 10. After sharpening press the stop pushbutton Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

41 3 Operation 11. Pull the handle to return the sharpener to its original position. 12. Lower the sharpener cover. Cleaning the grinding wheels The grinding wheel and its pin can be removed from the sharpener by taking it off in the direction of the arrow. For the sharpest blades the grinding wheel must always be clean. Remove dirt and grease with alcohol and the special brush supplied. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 3-29

42 3 Operation Guides lubrication This operation must be performed after cleaning the slicer or whenever the sliding action is difficult. Use Berkel slicer oil. Lubrication of the guide bar for the last slice device 1. Drop some oil on the bar. 2. Slide the last slice device along the guide bar. Lubrication of the guide bar for the product holder carriage 1. Pull the product holder towards the operator. 2. Pour lubricating oil into the special carriage bar lubricator. 3. Push the product holder to and fro and repeat the operation. Leave it at the operator end Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

43 Section 4 Installation Table of Contents: page no 4.1 RP-M251CE/M301CE/M351CE Positioning of slicer Electrical supply Preliminary cleaning 4-3 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 4-1

44 4 Installation 4-2 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

45 4 Installation 4.1 RP-M251CE/M301CE/M351CE Installation The slicer must be mounted horizontally on a stable, robust and antiskid base capable of supporting its weight (3.1.2 and 3.2.2). The recommended height of the working table is 800 mm. Check that the product holder is not clamped and the product to be cut can be easily loaded (3.1.2 and 3.2.2) Electrical supply The machine must be installed near a mains socket. Check that the power supply voltage corresponds to that on the information label and that it is correctly connected to earth. 1. Insert the plug into the mains socket. 2. Check that the blade cover fastening handle is screwed up tightly. 3. Check that the blade sharpener is lowered and that the protective cover is closed. 4. Press pushbutton to switch on the machine (the mains supply light will illuminate) Preliminary cleaning Before connecting the plug clean off the protective oil from the machine. Follow the instructions indicated in and Note: The working table must always be cleaned. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 4-3

46 4 Installation 4-4 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

47 Section 5 Electrical Drawings Table of Contents: page no 5.1 Wiring diagram RP-M251CE/M301CE Wiring diagram RP-M351CE Circuit diagram RP-M251CE/M301CE Circuit diagram RP-M351CE Circuit diagram RP-M351CE (Three Phase) 5-7 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 5-1

48 5 Operation 5-2 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

49 5 Electrical Drawings 5.1 Wiring diagram RP-M251CE/M301CE Blue Grey No. Colour 1 Red 2 Green 3 Grey 4 Brown 5 Blue 6 Black Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 5-3

50 Grey 5 Operation 5.2 Wiring diagram RP-M351CE M1 M2 T2 T2 Red Grey Blue Black No. Colour 1 Red 2 Green 3 Grey 4 Brown 5 Blue 6 Black 5-4 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

51 5 Electrical Drawings 5.3 Circuit diagram RP-M251CE/M301CE Red Brown Blue Green Grey Black POS DESCRIZIONE POS DESCRIZIONE X1 SPINA C3 CONDENSATORE 5F VS25E T1 TRASFORMATORE 0-230/0-24V 2,2VA C3 CONDENSATORE 8F GL25E-30E H-L-M25-30E F1 FUSIBILE 160mA R1/R2 RESISTENZA 2k2 1/4W D1 RADDRIZZATORE 1A R3 RESISTENZA 10k D2 DIODO DI PROTEZIONE G001 R4 RESISTENZA 47 Hom L1 LED LINEA ARANCIONE K1/K2 RELE DI COMANDO 12Vcc OMRON L2 LED MARCIA VERDE K3/K4 RELE DI COMANDO C1 CONDENSATORE ELETTROLITICO 220F 50V S1 PULSANTE STOP C2 CONDENSATORE ELETTROLITICO 220F 50V S2 PULSANTE START S3 PROTEZIONE DISCO COPRILAMA N o DISEGNO DATA MACCHINA S RP-M251CE/RP-M301CE TENSIONE: 230V-50Hz RP-M254CE/RP-M304CE Ci riserviarno la proprieta a termini di legge di questo disegno con divieto di riprodurlo anche in parte o di renderlo noto a terzi. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 5-5

52 5 Operation 5.4 Circuit diagram RP-M351CE Red Brown Blue Green Grey Black POS DESCRIZIONE POS DESCRIZIONE X1 SPINA R1/R2 RESISTENZA 2,2k 1/2W T1 TRASFORMATORE V/0-24V 5,5VA R3 RESISTENZA 47 OHM 1/4W F1 FUSIBILE 500mA R4 RESISTENZA 10k 1/4W D1 RADDRIZZATORE 1A K1 RELE DI COMANDO 24Vcc OMRON D2 DIODO K2 MINICONTATTORE 24Vcc ABB L1 LED LINEA VERDE K3 RELE DI AVVIAMENTO L2 LED MARCIA BIANCO S1 PULSANTE STOP C1 CONDENSATORE ELETTROLITICO 200F 35V S2 PULSANTE START C2 CONDENSATORE ELETTROLITICO 200F 35V S3 CONTATTO DI PROTEZIONE DISCO COPRILAMA C3 CONDENSATORE 35F 250V N o DISEGNO DATA MACCHINA S RP-M351CE TENSIONE: 230V-50Hz Ci riserviarno la proprieta a termini di legge di questo disegno con divieto di riprodurlo anche in parte o di renderlo noto a terzi. 5-6 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

53 5 Electrical Drawings 5.5 Circuit diagram RP-M351CE Red Brown Blue Green Grey Black POS DESCRIZIONE POS DESCRIZIONE X1 SPINA R1/R2 RESISTENZA 2,2k 1/2W T1 TRASFORMATORE V/0-24V 5,5VA R3 RESISTENZA 47 OHM 1/4W F1 FUSIBILE 500mA R4 RESISTENZA 10k 1/4W D1 RADDRIZZATORE 1A K1 RELE DI COMANDO 24Vcc OMRON D2 DIODO K2 MINICONTATTORE 24Vcc ABB L1 LED LINEA VERDE S1 PULSANTE STOP L2 LED MARCIA BIANCO S2 PULSANTE START C1 CONDENSATORE ELETTROLITICO 220F 35V S3 PROTEZIONE DISCO COPRILAMA C2 CONDENSATORE ELETTROLITICO 220F 35V N o DISEGNO DATA MACCHINA S TENSIONE: 230V-50Hz RP-M351CE RP-M254CE/RP-M304CE RP-M354CE/RP-M374CE RP-M353CE/RP-M373CE Ci riserviarno la proprieta a termini di legge di questo disegno con divieto di riprodurlo anche in parte o di renderlo noto a terzi. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 5-7

54 5 Operation 5-8 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

55 Section 6 Technical Information Table of Contents: page no 6.1 Adjustment of thickness plate Sharpener settings/adjustments RP-M251CE/RP-M301CE Sharpener settings/adjustments RP-M351CE Transmission belt - replacement/tensioning Product holder replacement 6-11 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 6-1

56 6 Technical Information 6-2 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

57 6 Technical Information 6.1 Adjustment of thickness plate Figure 6-1 Adjustment of thickness plate 1. Loosen the two screws (4) and move the thickness plate to within mm of the knife (2), as shown in Figure Fasten the thickness plate in position by firmly tightening the two screws (4). Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 6-3

58 6 Technical Information Figure 6-2 Adjustment of thickness plate As a result of shocks during transport, the thickness plate may sometimes come into contact with the knife; to re-set the thickness plate proceed as follows: 1. Lift the machine and loosen the screw (4) on the bracket (3). 2. Slowly rotate the thickness plate until the center of curvature of the edge next to the blade coincides with the centre of the knife, with an even opening of mm between the knife and the thickness plate, as shown above. 3. Fasten the thickness plate by tightening the screw (4) firmly. 6-4 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

59 6 Technical Information 6.2 Sharpener settings/adjustments RP-M251CE/RP-M301CE The knife must be replaced when its diameter falls to 10 mm less than its nominal value. The reduction of the knife diameter could mean that a corrective adjustment of the sharpener is needed. It should be positioned as follows: 1. Lift up the protection cover (pos 1 fig 6.3) and rotate the sharpener into its sharpening position (fig 6.3). 2. Loosen the two screws (pos 1 fig 6.3); loosen the bolt (spanner 22) (pos 3) and remove the sharpener assembly (pos 4). 3. Rotate the bolt (pos 5 fig 6.4) clockwise as far as is necessary, and assemble the sharpener assembly by checking that both stones are positioned as in fig 6.5, with the finishing stone parallel to the knife (fig 6.3); check that there is no interference with the movable protection (pos 6 fig 6.3). Put the sharpener into its non-operational position and check that there is no interference between the finishing stone and the knife. Fix the sharpener assembly by fastening the bolt (pos 3 fig 6.3). 4. Reset the knob (pos 2 fig 6.3) and fasten the two screws (pos 1 fig 6.3). Figure 6-3 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 6-5

60 6 Technical Information Figure 6-4 Figure Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

61 6 Technical Information 6.3 Sharpener settings/adjustments RP-M351CE The knife must be replaced when its diameter falls to 10 mm less than its nominal value. The reduction of the knife diameter could mean that a corrective adjustment of the sharpener is needed. It should be positioned as follows: 1. Lift up the protection cover (pos 1 fig 6.6) and rotate the sharpener into its sharpening position (pos 2). 2. Remove the caps (pos 2 and 3 fig 6.6); loosen the grain (pos 4 fig 6.7) and lower the sharpener until both stones are positioned in relation to the knife as shown in figs 2 and 2, and then fasten the grain (pos 4). 3. Loosen the grain (pos 5 fig 6.7); put the sharpener into its non-operational position (fig 6.6), and rotate the cam (pos 6 fig 6.7) anti-clockwise as far as possible. Loosen the grain (pos 8) and rotate the eccentric cam clockwise or anticlockwise (pos 9 fig 2) and check that the movable protection (pos 7 fig 6.6) projects beyond the knife edge, as shown in fig 6.6a, and then fasten the grain (pos 8 fig 6.7). 4. Return the sharpener to its sharpening position (fig 6.7) and rotate the cam clockwise (pos 6 fig 6.7), checking that there is no interference between the trimming stone and the movable protection (pos 7 fig 6.7) during the rotation, and then fasten the grain (pos 5). Figure 6-6a Figure 6-6 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 6-7

62 6 Technical Information Figure 6-7 Figure Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

63 6 Technical Information 6.4 Transmission belt - replacement/tensioning Before starting any operations disconnect the plug. Remove the blade with the blade removal tool. Operations 1. Disassembly and removal of the transmission and motor. 2. Replacement and adjustment of the belt. Figure Disassembly and removal of the transmission and the motor. a. Unscrew knob (A) and remove the blade cover. b. Remove the outer bushing (B) by loosening the screw which holds it to the bushing (C). c. Unscrew and remove the bushing (C) from the pin (D). d. Remove the blade. e. Remove the bottom cover. e. Disconnect the electrical wiring. f. Unscrew the 3 screws (P) fixing the motor/transmission to the casting and remove the motor. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 6-9

64 6 Technical Information Figure Replacement and adjustment of the belt. a. Mark the eccentric cam (E), in relation to its seat and notice the dimension(s). b. Remove the screw (G), which holds the eccentric cam in its seat by using a key, as shown above. c. Rotate the eccentric cam in its seat in order to draw the motor nearer to the transmission axis. d. Replace the transmission belt (H). e. Restore the eccentric cam in its original position (refer to the reference mark made earlier) and set the dimension(s) to the value noted earlier, and tighten the screw (G). Reassemble by following the reverse of the disassembly procedure Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

65 6 Technical Information 6.5 Product holder replacement 1 Product holder clamping handle 6 Stop nut 2 Product holder support 7 Threaded locking ring 3 Carriage 8 Alignment pin 4 Bed plate 9 Bush 5 Upper fixing screw 10 Support Figure Stop the carriage (3) at the end near the operator. 2. Place the product holder on the carraige (3) so that the upper fixing screw (5) sits on the support (10). 3. Loosen the threaded locking ring (7). 4. Turn the product holder clamping handle to the right to release the carriage. 5. Tighten the threaded locking ring (7). Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 6-11

66 6 Technical Information 6-12 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

67 Section 7 Appendices Table of Contents: page no 7.1 Slicer model coding system Routine maintenance Cleaning Knife control Knife sharpening Lubrication Sliding of the food holding carriage Endgrip sliding Supply cord Service checklist Options Option 8 Digital portioner Options 12, 22 Vegetable chute 135/180 mm dia Option 78 Carriage with dual fixing grippers (350) Option 91 Vegetable arm Option 93 Carriage with dual fixing grippers (250/300) Options 81, 100 Product fence 55/20 mm high Recommended parts RP-M251CE/M301CE RP-M351CE Exploded views with part numbers RP-M251CE/M301CE RP-M351CE Knife remover assemblies Knife part numbers 7-40 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-1

68 7 Appendices 7-2 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

69 7 Appendices 7.1 Slicer model coding system Product hierarchy Knife size Approvals RP - M 25 4 CE Combi Operation Configuration Weighing Product hierarchy RT = Range Top RP = Range Professional RM = Range Mid RE = Range Economy Operation M = Manual A = Semi automatic S = Stacker F = Fully automatic Knife size 22 = = = = = = 370 Configuration Table 1 = Gravity feed with standard table 2 = Straight feed with standard table (with standard pusher) 3 = Straight feed with articulating arm clamp 4 = Straight feed with sliding inner table 5 = Straight feed with top clamp P = Premier gravity feed with standard table E = Economy gravity feed with standard table Approvals CE = CE approvals ETL = USA approvals CSA = Canadian approvals Std. = Standard non CE product Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-3

70 7 Appendices 7.2 Routine maintenance Cleaning The slicer should be cleaned often; at least once a day. To clean all accessible parts, use a cloth moistened with water and detergent (a non aggressive one): do not use water jets! For effective cleaning follow the instructions given in the Instruction Manual Knife control Check the knife diameter and replace the knife when its diameter is 10mm less than its nominal diameter; for the replacement of the knife look at the specific technical sheet Knife sharpening When the slicing is not satisfactory, it is necessary to sharpen the knife. Before sharpening the knife clean the sharpening stone. If the sharpening is not satisfactory replace both stones Lubrication This operation should be made after the cleaning of the slicer, or each time when the carriage does not slide smoothly; use Berkel slicer oil Sliding of the food holding carriage If the carriage does not slide smoothly, lubricate its sliding bar as indicated in the Instruction Manual Endgrip sliding If the endgrip does not slide smoothly, lubricate its sliding bar as indicated in the Instruction Manual Supply cord Check periodically for wear of the supply cord: if you see that there are evident cuts, replace immediately. 7-4 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

71 7 Appendices Service checklist Machine: Slicer 1 Check for noise and faults, liaise with operators. 2 Check meat table assembly/carriage/pusher plate, ensure safety guards studs and screw function properly, lubricate assembly as necessary. 3 Remove knife plate checking screws and handles, check and adjust distance between centre plate and knife and the inner rim of knife to outside edge of centre of plate. 4 Clean back of knife adjust sharpener/sharpen knife. 5 Remove slice deflector, check tightness of adjustment plate, check and adjust distance between deflector and back of knife. 6 Remove knife with correct tool, lubricate knife shaft. 7 Check drive belts for tension and replace as necessary. 8 Lubricate slider bar and wheel rail, replace buffers as necessary. 9 Check electrical safety of machine. 10 Rebuild machine and realign gauge plates. 11 Ensure machine functions correctly after complete service. Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-5

72 7 Appendices 7.3 Options Option 8 Digital portioner 7-6 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

73 7 Appendices Option 12, 22 Vegetable chute 135/180 mm dia Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-7

74 7 Appendices Option 78 Carriage with dual fixing grippers (350) 7-8 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

75 7 Appendices Option 91 Vegetable arm Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-9

76 7 Appendices Option 93 Carriage with dual fixing grippers (250/300) 7-10 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

77 7 Appendices Option 81, 100 Product fence 55/20 mm high Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-11

78 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-12 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

79 7 Appendices 7.4 Recommended parts RP-M251CE/M301CE Part No. Description M251CE M301CE A1027 Sharpener assembly 1 1 C4813 Belt 1 1 E1420 Cam 1 1 I1682 On/off switch - membrane type 1 1 I1990A/Red Index knob assembly 1 1 I2040/Red End grip handle 1 1 I2095/Red Knob assembly - carriage support 1 1 L Knife 250mm 1 - L Knife 300mm - 1 M6601 Grinding stone 2 2 M6622 De-burr stone 2 2 M8356 Motor 220/240V 50Hz 1 1 P1019 Washer (pusher slide bar) 6 6 P1034 Plastic stop (pusher) 1 1 P1124 Slice deflector 1 - P1134 Slice deflector - 1 P5008 Foot 4 4 S3290 Circuit board 1 1 S3802 Index arm 1 1 T5119/Red Centre plate knob assembly 1 1 T8044 Knife shaft assembly 1 1 V7014X Knife screw 4 4 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-13

80 7 Appendices RP-M351CE Part No. Description M351CE A1026 Sharpener assembly 1 E1420 Cam 1 I1680 On/off switch - membrane type 1 I1990A/Red Index knob assembly 1 I2040/Red End grip handle 1 I2095/Red Knob assembly - carriage support 1 L Knife 350mm 1 M6602 Grinding stone 2 M6621 De-burr stone 2 M8469 Motor 1 P1019 Washer (pusher slide bar) 6 P1034 Plastic stop (pusher) 1 P3381 Grinding stone/spindle assembly 1 P3458 De-burr stone/spindle assembly 1 P5008 Foot 4 R2001 Motor start block 1 S3227 Circuit board 1 S3815 Index arm 1 T5006/Red Centre plate knob assembly 1 T8027 Knife shaft - bronze gear 1 V7014X Knife screw Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

81 7 Appendices 7.5 Exploded views with part numbers RP-M251CE/M301CE Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-15

82 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-16 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

83 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-17

84 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-18 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

85 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-19

86 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-20 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

87 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-21

88 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-22 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

89 7 Appendices RP-M351CE Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-23

90 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-24 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

91 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-25

92 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-26 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

93 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-27

94 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-28 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

95 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-29

96 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-30 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

97 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-31

98 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-32 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

99 7 Appendices Sharpener To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-33

100 7 Appendices Sharpener To order a part in RED suffix the part number with /RED i.e. I2040/RED Valid from to Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

101 7 Appendices Sharpener To order a part in RED suffix the part number with /RED i.e. I2040/RED Valid from Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-35

102 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-36 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

103 7 Appendices Motor To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-37

104 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED 7-38 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

105 7 Appendices To order a part in RED suffix the part number with /RED i.e. I2040/RED Service Instructions RP-M251CE/RP-M301CE/RP-M351CE 7-39

106 7 Appendices 7.6 Knife remover assemblies for CE models only Knife Diameter Part Number 220 mm SER/BER/ mm A mm A mm SER/BER/ Part numbers for knives Knife Diameter Standard knife Stainless steel Standard knife with remover holes Stainless steel knife with remover holes 220mm L mm L0602 L L mm* L0606 L L L L mm L0612 L mm L0623 L L L mm L0610 L *For model RP-M304CE only 7-40 Service Instructions RP-M251CE/RP-M301CE/RP-M351CE

107

108 You local service agent is: