IOM South Sudan WASH Pipeline Catalogue 2018

Transcription

1 2018

2 ii Table of Contents A. Hygiene Supplies 1 1. Multi -Purpose Soap 1 2. Hygiene Kit 1 3. Menstrual Hygiene Management Kit (MHM Kit) 2 B. Household Water Storage and Treatment 3 4. Bucket 20 litre with tap and lid Bucket 20 litres with lid 4 6. Collapsible Water Container 10L or 20L Water Treatment Flocculant and Disinfectant/ Purifier of Water (PuR) Water Purification Tablet, NaDCC, Aquatabs, 67 mg/tablet, box of 16,000 tablets 6 9. Filter Cloth in Pieces (Vestergaard) and in Rolls 6 C. Bulk Water Treatment, Storage and Distribution Aluminum Sulfate Powder 17-18% Calcium Hypochlorite / Chlorine High Test Hypochlorite (HTH) OXFAM Collapsible Water Tank 5 m 3, 10 m 3, 20 m 3 and Onion tank 30 m OXFAM Rigid Water Tank T45 and T OXFAM Tapstand with six taps. OXFAM equipment catalogue reference code: DS/7 12 D. Hand Pump Spare Parts and Tool Kits Standard Tool Kit for India Mark Handpump Special Tool Kit for India Mark Handpump Hand Pump Spare Part Fast Moving Kit India MK II Water Tank India MK II Pedestal Stand India MK II Head Assembly India MK II Cylinder Assembly India MK II Connecting Rod India MK Riser Pipe India MK II 18 E. Latrines Construction Materials Latrine Slab Tarpaulins / Plastic Sheet, 5 x 4 metres, min 220gr/m 2, reinforced. Specification used as per ICRC/IFRC standard Latrine Digging Kit 20 F. Water Testing Supply Pool Tester, 250 Tests kit, OXFAM Chlorine test DPD No 1, tablet, PAC -250 tabs/box Phenol Red, Ph , 250 tabs/box Delagua, Water Testing Kit, Bacteriological with power adapter, OXFAM 22

3 1 A. Hygiene Supplies 1. Multi -Purpose Soap A. Specification as per ICRC/IFRC standard: Multi-purpose soap, suitable for bathing, hand washing and laundry, fit for human use, marketable quality, of standard colour and odours. Contains minimum of 65% of fatty acid, which indicates the cleaning efficiency. Contains maximum of 0.5% NaOH which indicates the level of purity of the soap. The ingredients is not harmful to the skin The moisture content should not be higher than 20% at the time of packing. Weight per bar: minimum 800 gr when packed. B. Packaging: Bar individually packed. 25 bars in strong corrugated, export quality, carton boxes. Box dimension: 45 x 30 x 20 cm. The packaging has to provide crush resistance, moisture resistance and adequate strength for stacking in warehouses and during supplies transportation. Weight per box: minimum 20 kgs when packed. The packing must guaranty that bars are not damaged during the transportation. Required marking on the boxes: Product name Multi-Purpose Soap IOM and Donor s logos Manufacture dates Expiry dates Weight and Volume Ingredients details PO number Note Not for sale. All markings have to be clearly printed. Handwritten or sticker markings are not acceptable. Other requirements as per contract C. Procurement: Recommended local purchase where available 2. Hygiene Kit A. Specification: Basic hygiene items packed in a kit suitable for a household with five family members. B. Component per kit (subject to change based on revised needs) consisting of: 4 bars of 800 gr each multi-purpose soap, with date of expiry minimum 2 years after the date of delivery to IOM South Sudan.

4 2 -- Suitable for bathing, hand washing and laundry, fit for human use, marketable quality, of standard colour and odours. -- Contains minimum of 65% of fatty acid, which indicates the cleaning efficiency. -- Contains maximum of 0.3% NaOH which indicates the level of purity of the soap. The ingredients is not harmful to the skin -- The moisture content should not be higher than 20% at the time of packing. -- Weight per bar: 800 gr when packed. Good quality cotton towel, 50 x 100 cm, 2 pieces. Tooth paste, 3 tubes of 75 gr each, with date of expiry minimum 3 years after the date of delivery to IOM South Sudan, preferable Colgate brand Tooth brush, medium softness, 5 pcs, preferable Colgate brand Metal Nail cutter, 1 pc Hair Comb, 2 pc Nylon rope, for drying laundry clothes, 1 roll of 10 m Pack of razor blades, 1 box Safety pins, 1 set of 12 pcs All items have to be packed individually, in good quality and condition. C. Packaging: Dimension of bag: minimum 40 x 40 x 5 cm. Durable blue color bag with zip, made of cotton material, with product s name, IOM s logo and donor s logo clearly printed on every kit (different requirement as per contract. 20 kits are packed in in strong corrugated, export quality, carton boxes. The packaging has to provide crush resistance, moisture resistance and adequate strength for stacking in warehouses and transportation D. Procurement: recommended local purchase where available. 3. Menstrual Hygiene Management Kit (MHM Kit) A. Item specification: A kit which design to provide basic hygiene items to meet the specific needs of women and girls of menstrual age, with the purpose of facilitating their mobility and helping restore their dignity during time of crisis. B. Component per kit ((subject to change based on revised needs) consisting of: Reusable sanitary pads, color blue / pink color, AFRIPADS, 12 pcs, maxi size Women underwear, good quality cotton, color dark blue, M size 3 pieces, S size 3 pieces Multi-purpose soap, 1 bar of 800gr -- Suitable for bathing, hand washing and laundry, fit for human use, marketable quality, of standard colour and odours. -- Contains minimum of 65% of fatty acid, which indicates the cleaning efficiency. -- Contains maximum of 0.3% NaOH which indicates the level of purity of the soap. The ingredients is not harmful to the skin -- The moisture content should not be higher than 20% at the time of packing. -- Weight per bar: 800 gr when packed Instruction card in English and Arabic (as for distribution in South Sudan), printed in high quality paper, minimum 271 gsm, matte/gloss coating, laminated.

5 3 C. Packaging: Durable blue cotton bag with IOM logo, Donor s Logo (as per contract) and Menstrual Hygiene Kit printed on every kit. Every bag is equipped with black zip. 30 kits are packed in in strong corrugated, export quality, carton boxes. The packaging has to provide crush resistance, moisture resistance and adequate strength for stacking in warehouses and transportation. The packing must guaranty that kits are not damaged during the transportation. Required marking on the boxes: Product s name, IOM and donor s logos, weight and volume of each box, PO number, and note Not for sale. All markings have to be clearly printed Handwritten or sticker markings are not acceptable. D. Procurement: Recommended local procurement where available. B. Household Water Storage and Treatment 4. Bucket 20 litre with tap and lid. Strong flat plastic or anti rust metal handle without sharp edges and a roller grip strongly fixed to the bucket. Curved inside base to wall join for easy cleaning. Stackable for easy transport and storage. White color (bucket) with IOM logo and Donor s logo if required on the contract, on outside wall. Cover, handle and tap preferably red Weight per bucket: Minimum 860 gr (+/- 5%) IOM has the right to conduct quality test on buckets received. Tests will be as per ICRC standard. B. Packaging: 15 buckets are packed in in strong corrugated, export quality, carton boxes. The packaging has to provide crush resistance, moisture resistance and adequate strength for stacking in warehouses and transportation. Lids should be placed inside the box. The packing must guaranty that the buckets will not be presses one in other to avoid blocking the buckets together. Marking on the boxes: Product name, quantity, weight and volume, IOM and donor s logo, Note Not for sale, PO number, and other requirement as per contract. All markings have to be printed, sticker or hand written markings are not acceptable. C. Procurement: Recommended local procurement where available. A. Specification as per ICRC/IFRC standard Heavy duty plastic bucket/ water container, 20 litres capacity with built-in pressure tap, handle and removable tight-fit lid. Attached clip-on cap on the lid. The bucket is designed for transport and storage of clean, safe drinking water for domestic use Buckets made of virgin grade HDPE (High Density Poly Ethylene) and virgin LDPE (low density polyethylene), tough durable UV resistant and safe for food and drinking water storage (food grade material) Should not contain toxic elements. Brim full capacity: minimum 20 liters of water The top is reinforced to prevent ovaling, bottom part is reinforced to prevent scraping of the base Lid should be able to close tight, but easy to open and close

6 4 5. Bucket 20 litres with lid A. Item specification as per ICRC/IFRC standard: Heavy duty plastic bucket/ water container, 20 litres capacity with handle and removable tight-fit lid. Attached clipon cap on the lid. The bucket is designed for transport and storage of clean, safe drinking water for domestic use Buckets made of virgin grade HDPE (High Density Poly Ethylene) and virgin LDPE (low density polyethylene), tough durable UV resistant and safe for food and drinking water storage (food grade material) Should not contain toxic elements. Brim full capacity: minimum 20 litersthe top is reinforced to prevent ovaling, bottom part is reinforced to prevent scraping of the base Lid should be able to close tight, but easy to open and close. Strong flat plastic or anti rust metal handle without sharp edges and a roller grip strongly fixed to the bucket. Curved inside base to wall join for easy cleaning. Stackable for easy transport and storage. White color (bucket) with IOM logo and Donor s logo if required on the contract, on outside wall. Cover and handle preferably red Weight per bucket: Minimum 860 gr (+/- 5%) IOM has the right to conduct quality test on buckets received. Tests will be as per ICRC standard. B. Packaging: 15 buckets are packed in in strong corrugated, export quality, carton boxes. The packaging has to provide crush resistance, moisture resistance and adequate strength for stacking in warehouses and transportation. Lids should be placed inside the box. The packing must guaranty that the buckets will not be pressed one in other to avoid blocking the buckets together. Marking on the boxes: Product name, quantity, weight and volume, IOM and donor s logo, Note Not for sale, PO number, and other requirement as per contract. All markings have to be printed. Sticker or hand written markings are not acceptable. C. Procurement: Recommended local procurement where available.

7 5 6. Collapsible Water Container 10L or 20L. Every item must stand by itself, even when filled with less than ¼ of its maximum volume. Item could be collapsed/folded when not in use for easy transport and storage A built in carrying handle with minimum 9 cm length and 3 cm height, no sharp edges. Colour: translucent /ultraviolet (UV) stabilized, with/without IOM logo as per contract s requirement. If it is required, the logo must be engraved on each container. Weight per item: minimum 400 gr for 10L (+/- 5%) and minimum 500 gram for 20L (+/- 5%) Dimension per item: 30 cm x 20 cm x 25 cm for 10L, 40 x 30 x 25 for 20L Packaging: 25 pieces are packed in in strong corrugated, export quality, carton boxes. The packaging has to provide crush resistance, moisture resistance and adequate strength for stacking in warehouses and transportation. B. Procurement: Recommended local procurement where available. A. Item specification as per ICRC/IFRC standard: Description: square or rectangular shape foldable/collapsible jerry cans / water container, with a capacity of 10L or 20L according to the contract specification, with removable tight fit cap. Cap is attached to the container by polyamide string with diameter of minimum 1 mm and approximately 120 mm length. It is designed to transport and storage of safe drinking water for domestic use in emergency situation. Made of PVC coated polyester fabric, polyethylene, or equivalent material and should not contain toxic elements, UV resistant, suitable for drinking water storage. Design life: minimum 2 years of use under tropical conditions. 7. Water Treatment Flocculant and Disinfectant/ Purifier of Water (PuR). A. Item specification: Chemicals that promote flocculation in water treatment processes to improve the sedimentation or filterability of small particles found in the treated water. It also contains disinfectant. It comes in small sachet containing powdered ferric iron (a flocculant) % and calcium hypochlorite (a disinfectant) 0.546%. Suitable for water treatment at the household level. Brand: P&G Purifier, manufactured by P&G Each sachet contains iron sulphate and chlorine 1 box contains of 240 sachets, 4 gr/sachets 1 sachet to purify 10 liters / 2.5 gallons of water. Weight per box : 1.3 kg Box dimension: 25 x 18 x 11 cm Packaging : cardboard carton Expiry date: minimum 2 years from date of delivery B. Procurement: International for South Sudan mission, recommended local procurement for other missions.

8 6 8. Water Purification Tablet, NaDCC, Aquatabs, 67 mg/tablet, box of 16,000 tablets A. Item specification: as per ICRC/IFRC standard: Drinking water purification tablet contains 67 mg NaDCC, to enable water disinfection in emergency situation. Each tablet contains 67 mg NaDCC Sodium Dichloroisocyanurate Each table will treat 10 liters of water. Each tablet to give 0.6 mg/l residual chlorine after 30 minutes Product must be suitable for treatment of water for human consumption. Packaging: box of 16,000 tablets, in strips of 10 tablets each strip. B. Procurement: Recommended local procurement where available. 9. Filter Cloth in Pieces (Vestergaard) and in Rolls A. Item specification: A piece of cloth made of high quality nylon to filter drinking water contaminated by guinea worm and other carrying diseases microorganisms It comes in roll or piece, depending on the contract requirement. Cloth made of nylon mesh with pore size of approximately 150 μm. Size per roll: 1 m x 18 m. Size per piece: 1 X 1 m, with filter diameter 18 inch, Vestergaard. Color: white or light neutral. B. Packaging: For rolls: 50 rolls are packed n strong corrugated, export quality, carton boxes. The packaging has to provide crush resistance, moisture resistance and adequate strength for stacking in warehouses and transportation. Every rolls have to be neatly packed in clear plastic wrap. For Piece: 500 pieces are packed in strong corrugated, export quality, carton boxes. The packaging has to provide crush resistance, moisture resistance and adequate strength for stacking in warehouses and transportation. Marking on the boxes: Product name, quantity, weight and volume, IOM and donor s logo, Note Not for sale, PO number, and other requirement as per contract. All markings have to be printed. Sticker or hand written markings are not acceptable. Specification of the filter cloth has to be printed on every box or place inside every box C. Procurement: Recommended local procurement if available.

9 7 C. Bulk Water Treatment, Storage and Distribution 10. Aluminum Sulfate Powder 17-18% A. Item Specification as per ICRC/IFRC standard Chemical compound used as a flocculating agent in the purification of drinking water and waste water treatment plant. Comes in a bag of 50 kg powder Content: AL % minimum, iron free Weight per bag: 50 kg Bag dimension: 76 x 58 x 7 cm Packaging: Export grade bag, tear resistant polypropylene double bagged, 50 kgs each. Expiry date: minimum three years from date of delivery. All details including manufacture dates, expiry dates, weight and volume, and safety information should be clearly printed on each bag. Handwritten details is not acceptable. B. Procurement: Recommended local procurement where available. 11. Calcium Hypochlorite / Chlorine High Test Hypochlorite (HTH) A. Item Specification as per ICRC/IFRC standard Chemical used for disinfection of drinking water supplies, slime and odour control. It comes in form of granules (recommended), supplied in 45 kg drum. Granulated, contains 65 70% calcium hypochlorite, Ca(OCL)2. Packaging: polyethylene drums of export quality, with a lid and closure device to form an air tight seal to the drum. Packaging should follow ICRC standard packaging guidelines ICRC standard item, reference code: DASDCHLA7G45 (ICRC Emergency Relief Items Catalogue). Weight : 45 kg of Ca(OCL)2 per drum Drum dimension: 58 x 38 x 37 cm The chlorine content, expressed as a percentage of available chlorine, must be labelled on the packaging.

10 8 The chlorine content of the diluted solution must be expressed in a percentage, in parts per million (ppm) or in mg/ litre of available chlorine, for example: % of available chlorine, 1ppm or 1mg/litre. Free available chlorine (or residual chlorine) can be measured with a pool tester. Usage instruction, precaution, handling storage, toxicology information, first aid measures and all important items details have to be provided on every drum. Expire date, minimum 3 years from date of delivery B. Procurement: Recommended local procurement where available. 12. OXFAM Collapsible Water Tank 5 m 3, 10 m 3, 20 m 3 and Onion tank 30 m 3. A. Collapsible water tank 5 m3, OXFAM Equipment Catalogue reference code: TBT5 Item specification: 5m3 bladder tank, manufactured from UV resistant, food grade PVC coated polyester fabric (minimum 1100 g/m2). All materials used should be suitable for chlorinated drinking water. All seams to be either heat or high frequency welded. Tank fitted with the following items: 2 BSP(M) stub fitting with anti-chafe patch and flap 1 each Groundsheet 1 each Repair kit no glue supplied 1 each Holdall bag 1 each G234 Valve, Gate, 2 1 each Bush, Reducing, 2 BSP(M) to 1 BSP(F), GI 1 each G107 Adapter, Compression, 32mm - 1 BSP(M) 1 each G103 Tee, Compression, 32mm 2 each G220 Nipple, 2 BSP(M), GI 2 roll(s) GPT Tape, PTFE Resources included: Repair instruction, handling instruction, water storage equipment manual. Packaging: wooden crate Gross weight: 90 kg Volume: 0.48 m3 Dimension: 120 x 100 x 40 cm Procurement, International for South Sudan mission, recommended local procurement if available. B. Collapsible water tank 10 m3, OXFAM Equipment Catalogue reference code: TBT10/5 Item specification: 20m3 bladder tank, manufactured from UV resistant, food grade PVC coated polyester fabric (minimum 1100 g/m2). All materials used should be suitable for chlorinated drinking water. All seams to be either heat or high frequency welded. Tank fitted with the following items: 2 BSP(M) stub fitting with anti-chafe patch and flap 4 (internal measurement) screwed filler cap with captive cord 1 each Groundsheet 1 each Repair kit no glue supplied 1 each Holdall bag 2 each G234 Valve, Gate, 2 2 each Bush, Reducing, 2 BSP(M) to 1 BSP(F), GI 2 each G107 Adapter, Compression, 32mm - 1 BSP(M), PE

11 9 2 each G103 Tee, Compression, 32mm 2 each G220 Nipple, 2 BSP(M), GI 2 roll(s) GPT Tape, PTFE Resources included: Repair instruction, Handling Instruction and Water Storage Equipment Manual Packaging: wooden crate Gross weight: 140 kg Dimensions: 120 x 100 x 60 cm Procurement, International for South Sudan mission, recommended local procurement if available C. Onion Tank 30 m3, OXFAM Equipment Catalogue reference code: TRR30/5 Item specification: 30m3 self-supporting onion tank measuring 5.5m base diameter. Manufactured from UV resistant, food grade PVC coated polyester fabric (minimum 1100 g/m2). All materials used should be suitable for chlorinated drinking water. All seams to be either heat or high frequency welded. Tank to be fitted with the following: 2x 3 BSP(M) external stubs (fitted opposite each other) manufactured from LM25 (or equivalent) aluminium. Anti-chafe patches and flaps (PVC). 2x 3 BSP(F) internal stubs (fitted back to back with external stubs) manufactured from LM25 (or equivalent) aluminium 2 each G334 Valve, Gate, 3 2 extra welded patches for additional stubs 1 each Cover, PVC with fixings 1 each Groundsheet 1 each Holdall bag 2 each Bush, Reducing, 3 BSP(M) x 2 BSP(F) Reducing bush, GI 2 each Bush, Reducing, 3 BSP(M) x 1 BSP(F) Reducing bush, GI 2 each G220 Nipple, Hex, 2 BSP(M), GI 2 each G107 Adapter, Compression, 32mm 12 each G103 Tee, Compression, 32mm 2 roll(s) GTP Tape, PTFE 1 each Repair kit without glue Resource s included: Repair instruction, Handling instruction and water storage equipment manual Packaging: wooden crate Gross weight: 194 kg Volume: 0.48 m3 Dimensions: 100 x 120 x 40 cm Procurement, International for South Sudan mission, recommended local procurement if available.

12 OXFAM Rigid Water Tank T45 and T70 A. Rigid Water Tank T45, complete set of structure, liner, accessories and roof PVC. OXFAM Equipment Catalogue reference code: T45S/2, T45L/4, TUR Item specification: Complete set of rigid water tank, with capacity of 45 m3, made of corrugated galvanized steel sheets with liner, accessories and PVC roof, used for bulk water storage and treatment, preferably in emergency camp setting. Complete set (structure, liner accessories and roof) to be fitted with the following component: 11 pieces 6.4m Ø x 0.8mm corrugated galvanised steel sheets measuring 3.0m long x 0.8m high, drilled with 14mm holes on all sides (plain). Minimum tensile strength of all panels 90kN including a safety margin of 25% over maximum required design strength this permits the sheets to be interchangeable and used in tanks up to 95m³. 2 pieces of corrugated galvanised steel sheet with one hole drilled 95mm Ø for receiving a Flange Assembly, 3 (Oxfam code: G330), at midpoint of long side of sheet 175mm from edge to centre of hole. 1 piece corrugated galvanised steel sheet with bolt holes, one hole for flange drilled at the centre of the sheet. Hole blanked off with 225mm square plate made from same material and fixed in place with 4x M10 x 20mm round head bolts and nuts. 1 each EPDM synthetic rubber tank liner - suitable for potable water use 1 kit(s) Repair kit for Item 1 comprising: 1m² EPDM material, 10m roll of 50mm wide patching tape 21 metre(s) Split plastic primary wall capping, 12mm Ø 21 metre(s) Split plastic secondary wall capping, 25mm Ø 60 each Spring clip, 25mm steel - for capping 1 bag(s) Fixings: (x300) M10 20mm round head bolt, nut, washer, GI 2 each G334 Valve, Gate, 3 BSP(F), brass 3 each G330 Flange Assembly, 3 - comprising: threaded flange, flange with threaded 3 Ø pipe, synthetic rubber gaskets (x2), M16 steel studs (x4), M16 nuts and washers (x8) 1 roll(s) Tape, self-adhesive, 50mm wide, cloth-based (Gaffer), 55m 2 roll(s) GPT Tape, PTFE 1 roll(s) Rope, polypropylene, ultra-violet stabilized, 6mm x 50m 2 each Spanner, 17mm, open ended. 1 each upvc Cover with hem, 7.5m diameter, reinforced, conically shaped to suit roof pitch 210 metre(s) Rope, polypropylene, 6mm. Cut into m lengths (fitted to ridge plate) 1 roll(s) Rope, polypropylene, 6mm, 40m 2 each Pipe, 4, upvc, 1.31m length 2 each Pipe, 4, upvc, 0.75m length 3 each Connector, 4, upvc 28 each Eye nut, M10 1 kit(s) Repair kit for upvc cover, comprising: 1m² upvc material, 1 roll of twine and 3 needles 1 each Base stand, 600mm Ø with 4 upvc socket attached 1 each Ridge plate, 450mm Ø with 4 upvc socket attached and drilled with 28 holes - to accept polypropylene ropes Packaging: Structure: strapped together onto a pallet Liner and Accessories: wooden crate Roof: wooden crate

13 11 Gross weight: Structure: 253 kg Liner and accessories: 215 kg Roof: 83 kg Volume: Structure: 1.54 m 3 Liner and accessories: 0.8 m 3 Roof: 0.42 m 3 Dimension: Structure: 298 X 88 X 56 cm Liner and accessories: 147 x 79 x 71 cm Roof: 134 x 62 x 50 cm B. Rigid Water Tank T70, complete set of structure, liner, accessories and roof PVC. OXFAM Equipment Catalogue reference code: T70S/2, T70L/4, TUR Item specification: Complete set of rigid water tank, with capacity of 70 m3, made of corrugated galvanized steel sheets with liner, accessories and PVC roof, used for bulk water storage and treatment, preferably in emergency camp setting. Complete set (structure, liner accessories and roof) to be fitted with the following component: 18 pieces 6.4m Ø x 0.8mm corrugated galvanised steel sheets measuring 3.0m long x 0.8m high, drilled with 14mm holes on all sides (plain). Minimum tensile strength of all panels 90kN including a safety margin of 25% over maximum required design strength this permits the sheets to be interchangeable and used in tanks up to 95m³. 2 pieces of corrugated galvanised steel sheet with one hole drilled 95mm Ø for receiving a Flange Assembly, 3 (Oxfam code: G330), at midpoint of long side of sheet 175mm from edge to centre of hole. 1 piece corrugated galvanised steel sheet with bolt holes, one hole for flange drilled at the centre of the sheet. Hole blanked off with 225mm square plate made from same material and fixed in place with 4x M10 x 20mm round head bolts and nuts. 1 each EPDM synthetic rubber tank liner - suitable for potable water use 1 kit(s) Repair kit for Item 1 comprising: 1m² EPDM material, 10m roll of 50mm wide patching tape 21 metre(s) Split plastic primary wall capping, 12mm Ø 21 metre(s) Split plastic secondary wall capping, 25mm Ø 60 each Spring clip, 25mm steel - for capping 1 bag(s) Fixings: (x300) M10 20mm round head bolt, nut, washer, GI 2 each G334 Valve, Gate, 3 BSP(F), brass 3 each G330 Flange Assembly, 3 - comprising: threaded flange, flange with threaded 3 Ø pipe, synthetic rubber gaskets (x2), M16 steel studs (x4), M16 nuts and washers (x8) 2 roll(s) Tape, self-adhesive, 50mm wide, cloth-based (Gaffer), 55m 3 roll(s) GPT Tape, PTFE 1 roll(s) Rope, polypropylene, ultra-violet stabilized, 6mm x 50m 2 each Spanner, 17mm, open ended. 1 each upvc Cover with hem, 7.5m diameter, reinforced, conically shaped to suit roof pitch 210 metre(s) Rope, polypropylene, 6mm. Cut into m lengths (fitted to ridge plate) 1 roll(s) Rope, polypropylene, 6mm, 40m 2 each Pipe, 4, upvc, 1.31m length 2 each Pipe, 4, upvc, 0.75m length 3 each Connector, 4, upvc

14 12 28 each Eye nut, M10 1 kit(s) Repair kit for upvc cover, comprising: 1m² upvc material, 1 roll of twine and 3 needles 1 each Base stand, 600mm Ø with 4 upvc socket attached 1 each Ridge plate, 450mm Ø with 4 upvc socket attached and drilled with 28 holes - to accept polypropylene ropes Packaging: Structure: strapped together onto a pallet Liner and Accessories: wooden crate Roof: wooden crate Gross weight: Structure: 363 kg Liner and accessories: 249 kg Roof: 83 kg Volume: Structure: 1.5 m 3 Liner and accessories: 0.8 m 3 Roof: 0.42 m 3 Dimension: Structure: 297 X 8 X 56 cm Liner and accessories: 147 x 71 x 82 cm Roof: 134 x 62 x 50 cm Procurement, International for South Sudan mission, recommended local procurement if available. 14. OXFAM Tapstand with six taps. OXFAM equipment catalogue reference code: DS/7 A. Rigid Water Tank T45, complete set of structure, liner, accessories and roof PVC. OXFAM Equipment Catalogue reference code: T45S/2, T45L/4, TUR Item specification: stand of 6 pressure taps connected to water supply, for bulk water distribution. Suitable for water distribution in camp setting. Complete set include: 1 each Hollow section frame, 40mm x 40mm section, fitted with: Inlet in centre of one side to connect 1½ BSP(M) pipe, (x4) 1 BSP (F) sockets angled to receive the leg pieces, (x6) ¾ threaded outlets 6 each Nipple, Barrel, ¾ BSP(M) x 300 mm, GS - for taps 4 each Frame legs, 1 Ø x 1m long, GS - one end threaded to fit frame and other with foot plate 1 each Nipple, Barrel, 1½ BSP(M) x 600mm, GS - for inlet 4 each Coach bolt and nut, M10 100mm long with nut 4 each Coach screw, ⅜ 3 long - for mounting on timber frame 2 roll(s) PTFE tape 6 each DV/2 Valve (Tap), Evenflow type, ¾ BSP(F), Aluminium 2 each End cap, ¾ BSP(F), GI 1 each G107 Adapter, 32mm Compression x 1 BSP(M), PE 1 each Tee, Reduced branch, 2-1½ BSP(F), GI 1 each End Plug, 2 BSP(M), GI 1 each Bush, Reducing, 2 x 1 BSP(M-F), GI

15 13 1 each Adapter, 50mm Compression x 2 BSP(M), PE 1 each Guillemin half coupling x 2 BSP(M), without locking ring, aluminium D. Hand Pump Spare Parts and Tool Kits 15. Standard Tool Kit for India Mark Handpump A. Item specification: Description: Set of standard tools for India Mark II for Installation and Maintenance of Standard Deep Well Hand Pumps (SDWP) and Extra Deep Well Hand Pumps (EDWP), also called IM II, India Mark II, and Mark II hand pumps Content per kit as per table below (kit may be customized): Ref# Item Quantity 1 Mild steel galvanized tool box with locking arrangement 1 2 Hammer, Approx. 1kg, drop forged with a varnished wooden handle 1 3 Nylon Rope 3mm Thick 75 m 4 Pressure type oil can and mobile oil ½ kg 1 each 5 Wire Brush With Wooden Handle 1 6 Box Of Multipurpose Grease 1 7 Spirit Level 1 8 Adjustable Spanner 250mm Drop Forged With Heat Treated Injection Hardened Polished Jaws. 1 9,10 Die Set For Threads Of 32mm NB GI Riser Pipe 1 Set 11 Pipe Wrench,450mm Drop Forged Carbon Steel 2 12, 18 Button Die Set For 12mm Threads 1 set 13 Pipe Wrench,600mm Drop Forged Carbon Steel 1 14 Six Spare Blades 6 15 Hack Saw With 300mm Blade 1 16 Double Ended CV Open Jaw Spanner M17 X M Flat File 250mm With A Wooden Handle 2 18 Screw Driver 250mm X 8mm Engineering Type 2 Weight per kit: minimum20 kgs Dimension per kit: 56 x 22 x 12 cm List of item is required, printed in a good quality of paper, laminated, and to be placed inside every kit. B. Procurement: Recommended local purchase where available

16 Special Tool Kit for India Mark Handpump A. Item specification: Description: Set of special tools for India Mark II for Installation and Maintenance of Standard Deep Well Hand Pumps (SDWP) and Extra Deep Well Hand Pumps (EDWP), also called IM II, India Mark II, and Mark II hand pumps. Content per kit as per table below (kit might be customized): Ref# Item Quantity 1 Mild Steel Galvanized Tool Box with Locking Arrangement (to accommodate all items except 3 and Connecting Rod Vice 1 3 Self-locking Clam or Heavy Duty Clam for 32 mm NB GI Pipe 1 4 Water tank lifter 1 5 Bearing pressing /Mounting tool 1 6 Rod coupling spanner 1 7 Connecting rod lifter 1 8 Handle Axle Punch 1 9 Chain Coupler Supporting Tool 1 10 Crank Spanner M17 x M Pipe Lifting Spanner 3 Weight per kit: minimum 28 kgs Dimension per kit: 28 x 28 x 12 cm List of item is required, printed in a good quality of paper, laminated, and to be placed inside every kit. C. Procurement: Recommended local purchase where available

17 Hand Pump Spare Part Fast Moving Kit India MK II A. Item specification: Description: set of fast moving Spare parts for maintenance of EDWP (India Mark II) hand pumps, per kit as per table below (kit might be customized): Ref# Item Quantity 1 Nitrile Rubber Sealing Ring 6 2 Nitrile Rubber Cup Washer 4 3 Nitrile Seating (big) 1 4 Nitrile Seating (small) 1 5 GI pipe coupling 2 6 Handle axle 1 7 Bearing 6204-Z SKF 2 8 Chain with coupler 1 9 Spacer 1 10 Hex coupler 12 x 1.75 x High tensile hex bolt M10 x 1.5 x Washer 4 mm thick for axle 1 13 Bolt for front cover 12 x 1.75 x Hex nuts M12 x Hex bolt M12 x 1.75 x Nyloc nut M10 1 Weight per kit: minimum 2.5 kgs Dimension per kit: 27 x 14 x 8 cm List of item is required, printed in a good quality of paper, laminated, and to be placed inside every kit. B. Procurement: Recommended local purchase where available

18 Water Tank India MK II A. Item specification: Description: Part of India MK II pump, in which water from the pipes collected before it goes out through the tap; it is where the rising main is connected using thread in the riser pipe. Item is welded and hot dip galvanized Ref# Item Quantity 1 Mild Steel Galvanized Tool Box with Locking Arrangement (to accommodate all items except 3 and Connecting Rod Vice 1 3 Self-locking Clam or Heavy Duty Clam for 32 mm NB GI Pipe 1 Weight per tank: 7.8 kgs Dimension per kit: 47 x 19 x 26 cm B. Procurement: Recommended local purchase where available 19. Pedestal Stand India MK II A. Item specification: No Description: The outside main body of the borehole, for protection of the parts inside Item 1 Stand assembly (welded and hot dip galvanized) 2 Anchor assembly (welded with Stainless Steel bolts M16) 3 Hexagonal bolt M16 x 150,(for Anchor/Pump stand) 4 Washer for M16 (Brass) Weight per piece: 18.5 kgs Dimension per kit: 90 x 17 x 20 cm B. Procurement: Recommended local purchase where available

19 Head Assembly India MK II A. Item specification: Description: Part of India MK II pump, in which water from the pipes collected before it goes out through the tap; it is where the rising main is connected using thread in the riser pipe. Item is welded and hot dip galvanized No Item 1 Head assembly (welded and hot dip galvanized) 2 Front cover assembly (welded and hot dip galvanized) 3 Hexagonal bolt M12 x 40,(for Pump head/water tank) 4 Hexagonal nut M12 (for Pump head/water tank) 5 Handle arrangement (Handle assy , Chain assembly A2525 and all handle axle parts, complete) 6 Handle assembly (welded and hot dip galvanized) 7 Chain assembly Weight per piece: 24 kgs Dimension per kit: 126 x 22 x 28 cm B. Procurement: Recommended local purchase where available

20 Cylinder Assembly India MK II A. Item specification: Main part of India MKII Hand pump, main pump which is set in the aquifer deep underground. This item include: the plunger rod, upper and lower valves, rubber seating and sealing rubbers, brass liner, reducer caps and cylinder body. The depth that a pump is set is based on the desired yield rates. A minimum yield of 1-2 cubic meters per hour is usually targeted. Description: The outside main body of the borehole, for protection of the parts inside Cast Iron Body painted outside and lined from inside with seamless Brass liner at 63.5mm I.D., Gun-metal valve components and Nitrile rubber components. Discharge capacity is strokes per min. Weight per piece: 6.8 kgs Dimension per kit: 61 x 9 x 8 cm B. Procurement: Recommended local purchase where available 22. Connecting Rod India MK A. Item specification: Description: 12mm diameter mild steel electro galvanized, in three meter lengths with hexagonal coupling of both the ends for use with India Mark II / IM III hand pump. Connecting rods are attached to the pump cylinder. This drives the pistons which draws water from the well. Weight per piece: 2.7 kgs Dimension per piece : 300 x 1.2 cm B. Procurement: Recommended local purchase where available 23. Riser Pipe India MK II A. Item specification: Description: 32mm N.B., G.I. Medium pipe in three meters length with a socket at one end. It carries water up to the tap. Weight per piece: 8.3 kgs Dimension per kit: 300 x 3.2 cm, B. Procurement: Recommended local purchase where available Thin one is 22, thick is 23

21 19 E. Latrines Construction Materials 24. Latrine Slab A. Item specification: Description: Moulded polypropylene squatting plates for human excrement management in emergency situation. Manufactured in vermin and termite proof polypropylene. Lightweight and strong with rigid, smooth surface for easy cleaning. Feet placement areas designed to prevent slipping. Weight: 11.5 kg Plate dimension: 120 x 80 x 5.5 cm Colour: maroon or neutral colour. Brand: NagMagic (recommended) This slab can be used as a direct drop selfsupporting slab or a pour-flush slab. Slab can be used on shallow or deep trench or pit without any additional support to provide a hygienic surface with a well fitted lid. Shipping: 35 or 40 slabs are stacked on a standard Euro pallet. B. Procurement: Recommended local purchase where available 25. Tarpaulins / Plastic Sheet, 5 x 4 metres, min 220gr/m 2, reinforced. Specification used as per ICRC/IFRC standard. 1m 4m 1m 5m

22 20 A. Item Specification: Reinforced and waterproof tarpaulins for emergency sanitation facilities purpose, designed for long outdoor use in all climates Finished size of each sheet is 4 x 5 metres (+/- 5%); m2 Material: made of woven high-density black polyethylene (HDPE) fibers, warp x weft, laminated on both sides with low-density polyethylene (LDPE) coating, with reinforced rims by heat sealing on all sides (or 2 sides heat sealing and 2 sides double stitching), and nylon ropes in hem denier minimum. Material weight: minimum 220gr/m2 (+/-5%) Tensile strength: minimum 600 N both directions of warp and weft (BS2576, 50mm grab test, or equivalent) Tear strength: minimum 100 N both directions (BS 4303 wing tear or equivalent) UV Resistance: stabilized against ultraviolet rays and excess heat for long outdoor exposure. Maximum 5% loss on original tensile strength under ISO 1421 after 1500 hours UV under ASTM G53/94 (UVB 313 nm peak) Flammability: flash point above 200 degrees C (CPAI , section 6) Colour: White on both side with IOM logo and Donor s logo as per contract. Width: 4 m minimum Length: 5 m minimum Weight per piece: min 4.5 kg (+/- 1%) Weight per bale: min 22.5kg/bale (+/- 1%) Dimension per bale: 57 cm x 42 cm x 18 cm. Packaging: There must be 5 pieces of tarpaulins packed in a bale. The bale must be wrapped with a piece of similar materials as one of the tarpaulins. The warping must be properly folded, closely tight to the bale content, making a well-shaped cubic bale. The bale must be strapped with 2 heatsealed plastic straps for the length and 2 for the cross, and well-sealed with large adhesive tape. Lifespan expectancy: 1 year under the strongest weather conditions, could be re-used and re-cycled. All specification and technical control to follow ICRC/IFRC standard. B. Procurement: Recommended local purchase where available 26. Latrine Digging Kit A. Items specification: a kit of high quality, durable hand tools designed for general ground preparation works such as latrine digging, trench and pit digging.

23 21 Component details: No Items 1 1 piece of shovel, round mouth blade, with wooden handle 2 1 piece of pickaxe head, chisel and point 3 1 piece pickaxe handle, hardwood 4 Bucket, 16 liters, galvanised steel 5 Digging bar with pointed and blunt ends, 3 cm diameter, 1,5 m length, iron 6 1 roll of 5 m length and 8 mm thickness rope, polypropylene Packaging: loose Gross weight: 9.5 kg/kit Gross volume: 0.26 m 3 /kit B. Procurement: Recommended local purchase where available F. Water Testing Supply 27. Pool Tester, 250 Tests kit, OXFAM. A. Item Specification: Description: Tool for measuring free available chlorine, acid demand, Ph (acidity) of water samples and total alkalinity. OXFAM standard item, reference code: FPO/2 Chlorine range mg/l ph range in increments of 0.2 Components as per OXFAM Equipment Catalogue: Ref# Item Quantity Description 1 1 each Colour comparator unit 2 20 tab Rapid Test DPD1 (20 Cl residual tests) 3 20 tab Rapid Test Phenol Red (20 ph tests) Additional required tablets should be ordered separately Weight per kit: 0.2 kg Dimension: 20 x 10 x 12 cm B. Procurement: Recommended local purchase where available

24 Chlorine test DPD No 1, tablet, PAC -250 tabs/box A. Item specification: Description: Chlorine DPD No 1 tablets for testing free chlorine in drinking water using colorimeter, photometer or disc comparator. Brand: Lovibond Water Testing Weight per box: 10 gr Box dimension: 10 x 9 x 4 cm 1 box contains 25 strips, 10 tablets each strips. B. Procurement: Local purchase where available. 29. Phenol Red, Ph , 250 tabs/box. A. Item specification: Description: Phenol Red are used for testing the ph level in drinking water using a digital photometer or visual disc comparator Brand: Lovibond Water Testing Weight per box: 10 mg Dimension: 10 x 9 x 4 cm 1 box contains 25 strips, 10 tablets each strip. B. Procurement: Local purchase where available. 30. Delagua, Water Testing Kit, Bacteriological with power adapter, OXFAM A. Item specification: Portable water quality, bacteriological testing kit to measure for total coliforms and faecal coliforms. OXFAM standard item, reference code: FKA/1 Components included (as per OXFAM Equipment Catalogue 2014)

25 23 Ref# Item Quantity Description 1 Delagua test kit body and carrying case Ancillaries 1 each 2 Turbidity Tube 1 each 3 Pooltester for Chlorine/pH Testing 1 each 4 Thermometer, 10/+50 C 1 each 5 Incubator lid 1 each 6 Incubator lid with hole - for recalibration 1 each 7 Petri dishes, 16pc, with carrier 3 each 8 Methanol dispenser/dropper bottle 1 each 9 Culture medium bottle, 60 ml 10 each 10 Tweezers/forcep 1 each 11 Screwdriver, Small, for temperature calibration 1 each 12 Adapter, Power, 110/240V AC input, 12V DC output 1 each 13 DC Battery connection cable with crocodile clips 1 each 14 Hand lens 1 each 15 Stopwatch/timer, digital Filtration apparatus (Part 10703, complete) 1 each 16 Aluminium base - for filter 1 each 17 Filter funnel with collar, plastic 1 each 18 Sample cup with hole for cable, stainless steel 1 each 19 Vacuum cup, stainless steel 1 each 20 Pump, Vacuum 1 each 21 Lanyard/cable for sample cup 1 each 22 Bronze disc, membrane support 1 each 23 Silicon sealing gasket - for bronze disc 1 pair 24 Black rubber O-ring 1 each 25 Sealing grease, 2g 1 each 26 Silicone sealing gasket 1 pair 27 Bronze disc 1 each 28 Black rubber O-ring 2 each 29 Absorbent Pads - Gelman 2 tube 30 Pad dispenser tool 1 each 31 Filter, Membrane - for Water Testing 1 pack 32 Broth - Lauryl Sulphate 2 tub 33 Tablets, Rapid Test, DPD1 1 pack 34 Tablets, Rapid Test, DPD3 1 pack 35 Tablets, Rapid Test, Phenol Red 1 pack Resources included Unit Description 1 manual(s) Instructions English 1 cd(s) Instructions English Other items included in the kit as per OFAM catalogue Gross weight: 11 kg Volume: m3 Dimension: 50 x 42 x 21 cm B. Procurement: Local purchase where available.

26 INTERNATIONAL ORGANIZATION FOR MIGRATION SOUTH SUDAN