Professional Installation Guidelines LVT with Roll-out Loop over LocPlate products. Required Tools
|
|
- Berenice Anthony
- 6 years ago
- Views:
Transcription
1 Professional Installation Guidelines LVT with Roll-out Loop over LocPlate products Required Tools Utility Knife Hook Blade Knife Chalk Line Poly Sheeting Measuring Tape Straight Edge 75 lb Roller TacFast Disc Locker General Conditions and Preparation Use only TacFast-approved surfaces and tools. General conditions for the installation of LVT apply. Store Hook Plates, Discs and LVT for 48 hours in the room to be installed. Keep room above 65 F (18 C) during that time and during the installation. After installation, the temperature of the room/floor should not fall below 65 F (18 C). Floor temperature should not exceed 85 F (29 C). This must be considered when installing over radiant floor heating. Sweep the floor before starting the installation. Pre-plan you installation layout to ensure that roll-out loop seams are NOT in line with the Hook Plate seams. The installation of the roll-out loop should be offset to the Hook Plate seams by a MINIMUM of 4". The LVT pieces should also be offset to the loop seams by 3" to 4". Installation of Hook Plates & Discs 1 Trim the overlaps on the first hook plate. Starting in the corner of the room, Place the cut edges towards the two edges of the installation starting point (walls or installation edge). Remove all Hook Plate overlaps against the installation edge. The overlaps must always face in the same direction as the first Hook Plate that was installed. 2 Lay the Hook Plates against the installation edge. Note: If the installation edge is a wall, a gap between the wall and the hook plates is allowable so long as it does not exceed 1/4". 3 Once 4 Hook Plates have been laid, a circular void is created. The Hook Plates will be locked together using the Disc. 4 The Disc is inserted, by hand, into the circular void, which is the space created when 4 Hook Plates come together. Insert the disc into the corresponding holes and twist clockwise into the pre-locking position. 5 The Discs are then locked into position using the TacFast Disc Locker.
2 6 Trim/cut both Hook Plates and Discs where necessary. To cut: Score the Hook Plate or Disc with the knife, then flex it in the direction of the score to split it. 7 If there is an underlayment attached to the hook plate and/or disc such as foam or fleece, use the knife to cut the through the underlayment after you have cut the hook plate. Notes: If the installation of the Hook Plates and Discs is interrupted for a period of time (e.g. the installation is scheduled during the evening hours and has not been completed prior to business opening the following morning), install the Discs along the last completed row of the Hook Plates. Temporarily cover the exposed Hook Plates with a suitable material (e.g. cardboard that is taped to the concrete floor on one side and to the vinyl surface on the other side). When the installation is resumed, remove both the material covering the exposed Hook Plates and the Discs that were temporarily installed. Continue with the installation. Do not expose Hook Plates and Discs to mechanical abrasion such as but not limited to dragging furniture, cuts and improper protection when using heavy machinery or moving heavy rolling stock as damage or destruction of hooks can occur. Storing the Hook Plates and Discs Storage Requirements It is imperative that TacFast Hook Plates and Discs be stored according to the specifications outlined below in order to avoid damage. General Conditions The Hook Plate boxes must sit on a flat surface that fully supports the under surface of the box. If stacked on a skid or pallet, a plywood board or oriented strand board (OSB) of at least 5/8 thickness and of an appropriate size (ie. protruding on every side of the Hook Plate boxes by at least 1 ), must be placed on the upper surface of the skid and on the top layer of Hook Plate boxes on the skid. Hook Plate boxes must always be stored horizontally (flat). Do not expose to substances which destroy or change the properties and/or form of the LocPlate products such as hydrochloric acid, petrol (gasoline), nitric acid, ethylether, chloroform, carbon disulphide, carbon tetrachloride, methylene (di)chloride, trichloroethylene, etc. Environmental Conditions The maximum storage temperature should not exceed 50 C (120 F) longer than 50 hours and not 35 C (100 F) for periods longer than 3 weeks (500 hrs). The minimum storage temperature should not be lower than 10 C (50 F). Hook Plates and Discs must be acclimatized prior to installation. Do not store outside. Do not expose the packaging to moisture. Do not expose Hook Plates and Discs to direct sunlight for any period longer than necessary, more specifically not longer than 30 minutes. Stacking Height Do not stack higher than 30 boxes stack height. For every 10 boxes, a plywood board or oriented strand board (OSB) of at least 5/8 thickness of appropriate size (fully supporting the boxes on top and protruding on every side of the boxes by 1 ) has to be inserted Disc boxes must be stored so that the Disc boxes are lying down.
3 Helpful Tips Detailed instructions on how to lock a Disc 4 Hook Plates together create a circular void Place the Disc into the circular void Proper position is defined as the mushrooms on the Disc being partially rotated under the white plastic parts of the Hook Plates. Line up the mushrooms on the Disc into the slots in the Hook Plates. This must be done by hand prior to using the Disc Locker. This procedure is considered to be putting the Disc in the pre-locked position. Disc in pre-lock position prior to using the Disc Locker. Note that all 4 mushrooms must be in position and be partially turned. This ensures that when the Disc Locker is used, all 4 of the mushrooms will lock. If they are not all properly placed at this point, they will not lock when the Disc Locker is applied. Disc Locker Pin locations Close-up of the pre-locked Hook Plate and Disc. Once the Disc is in the pre-locked position, the Disc Locker can be placed into the Disc by lining up the pins on the Disc Locker with the slots. Disc Locker is turned to lock the Disc into the Hook Plates. Locked Hook Plates and Disc.
4 Trimming Discs to provide a 1/2 Disc or a 1/4 Disc Some of the Discs will have raised guidelines on the underside of the Disc. These guidelines have taken into account the slight turn that will take place when the Discs have been locked. Align a straight edge to the raised lines. Score and snap as necessary. If the Discs do not have the raised lines on the underside, follow the guidelines below to cut into required size: For half a Disc: Place 2 Hook Plates together (as if to install the Hook Plates) Install a Disc between the 2 Hook Plates and lock it into position. Once Disc is locked, score the Disc using the underlap edge of the 2 Hook Plates as a guide. A straight edge aligned along the underlap edge of the Hook Plates can also be used as a guide. Unlock and remove the scored Disc Bend and snap Disc into 2 pieces. For a quarter Disc: Place 4 Hook Plates together (as if to install the Hook Plates) Install a Disc and lock it into position. Once Disc is locked, score the Disc, in both directions, using the underlap edges of the Hook Plates as a guide. A straight edge aligned along the underlap edges of the Hook Plates can also be used as a guide. Unlock and remove the scored Disc Bend and snap Disc along the score lines so as to break the Discs into 4 pieces. Note: Once a single Disc has been cut, one of the pieces can be used as a template for cutting additional Discs (if required). Notes: It is important that the Discs be aligned to the underlap edges not the overlap edges. If aligned to the overlap edges, the Discs will be too large. It is necessary to twist and lock the Discs into the Hook Plates to ensure that the trims are made in the right place (taking into account the slight turn when locking the Disc occurs). Installation of the Roll-out Loop Description of the Roll-out Loop Roll-out Loop is a loop material comprised of: a stabilized loop material a pressure-sensitive adhesive (PSA) a pressure-sensitive adhesive (PSA) liner The PSA does not extend to the nominal edge of the loop. This results in the loop having an average of 1/2" to 3/4" of loop material uncoated (no adhesive) on each edge along the length of the roll. Loop surface Adhesive (PSA) Adhesive (PSA) Liner Pre-plan the roll-out loop installation layout to ensure that the seams overlap the hook plate seams. There should be a MINIMUM OF 4" overlap. 1 Beginning with the longest and straightest wall, roll out enough poly sheeting to cover the Hook Plates & Discs for the first section of loop to be installed. 2 Roll out the loop material (over the poly sheeting) so that the loop side is down and the PSA side with the liner is face up. Allow the loop to run-up the wall and dry-lay into position. Alternatively, the first section of loop material can be installed a distance from the wall (distance must be less than the width of the loop material). The uncovered area from the loop material to the wall can be backfilled later. Loop material 3 Once the loop is in position, fold back a small section of the loop. 4 Fold back a section of the poly sheeting so that the hooks on the LocPlate substrate are exposed. 5 Fasten the loop material to the hooks by folding the loop back over again. Apply pressure to the loop material ensuring that it is well fastened to the hooks. 6 Carefully remove the remainder of the poly sheeting from between the LocPlate substrate and the loop material, fasting the loop material by engaging the mechanical bond. Ensure that the loop material is lying flat and that there are no bubbles, ripples or creases as these will telegraph through the LVT later.
5 7 Trim the excess loop material along the wall. 8 Layout poly sheeting for next section of the loop material. 9 Dry-lay second section of loop material ensuring that it overlaps the first installed piece by one to two inches. Ensure that the overlapped edges include PSA. 10 Repeat steps 3-6 as above to install second section of loop. 11 Once the second section has been installed, using the hook blade/hook knife, double cut the loop material. This will ensure a clean cut while also removing the loop edge with no PSA. Note: After the installation of the first two sections of loop material, the installers can choose to continue to install the balance of the loop material or they can begin the installation of LVT surface. The loop material can continue to be installed concurrent with the LVT installation. Installation of LVT Surface Only TacFast-approved surfaces may be installed. Pre plan the LVT installation layout to ensure that the LVT seams overlap the Hook Plate seams. There should be a MINIMUM of a 3"- 4" overlap. Use traditional layout patterns for LVT (Tiles and Planks). ie. staggering the planks. The LVT installation starting point will depend on whether the surface will be installed concurrent with the balance of the loop material installation or if the LVT will be installed after all of the loop material has been installed. Starting Point for Concurrent Installation: Remove the PSA Liner (exposing the adhesive) on the 1st section of installed loop material. Following your installation layout to ensure that the seams of the LVT do not align with but overlap the seams on the loop material, snap a chalk line along the length of the loop material. 1 Starting Point for Installation after all Loop Material has been installed: Remove the PSA Liner (exposing the adhesive) from the centre section of the installed loop material. Snap a chalk line across the center of the installation area in both directions to find the centre point of the area. Ensure that the centre point is a minimum of 4" from the loop material seams in each direction. Loop material (PSA side up) Removal of PSA liner 2 Starting along the chalk line or from the intersection point in the center of the floor, install the tiles along the chalk line that runs parallel to the longest, straightest wall by laying the LVT onto the exposed adhesive on the loop material. 3 Continue to install the LVT along the chalk line moving up and down along the line checking periodically to ensure the LVT is properly aligned at the edges.
6 Note: The LVT can be lifted and repositioned onto the adhesive so long as the LVT has not been pressed into the adhesive. The process of rubbing or pressing the LVT into the adhesive will make it difficult to lift and reposition the LVT. 4 Use the utility knife to trim LVT where necessary. 5 Continue to install the LVT removing the PSA Liner on each adjacent section as necessary. 6 When the LVT installation is complete, roll with a roller.
INSTALLATION INSTRUCTIONS FOR BALCO, INC. FLOOR MATS FM2R-(A, C, D) W/O FRAME 4V
2626 South Sheridan PO Box 17249 Wichita, Kansas 67217 Phone: (316) 945-9328 Fax: (316) 945-0789 INSTALLATION INSTRUCTIONS FOR BALCO, INC. FLOOR MATS FM2R-(A, C, D) W/O FRAME 4V 2012, Balco, Inc. INSTALLATION
More informationSolar Power Shade INSTRUCTION MANUAL
INSTRUCTION MANUAL 20 June 2006, Revision Initial Release 26 September 2006, version 2 Powerfilm, Inc. 2337 230th Street Ames, IA 50014 (515) 292-7606 Web Site: www.powerfilmsolar.com Table of Contents
More informationRUPHIS Blade Clamp. Instruction Manual
RUPHIS Blade Clamp P/N 1006800 NSN 1615-01-562-8156 Instruction Manual AH-64D UH-60A/L UH-60M S-70i S-92 REVISION AUTHORIZATION / RECORD These instructions are primarily for inspection of the RUPHIS Blade
More informationPL500A Platform Extension
PL500A Platform Extension Operator Manual Copyright 2009 ServerLift Corporation 821 N 2nd Street Phoenix, AZ 85004 VOICE: 602.254.1557 FAX: 602.412.4479 821 N 2nd Street Phoenix, AZ 85004 VOICE: 602.254.1557
More informationCJ-7 YJ PREPARATION INSTALLING THE WHEEL WELLS. Jeep Wrangler CJ-7/YJ BedRug Interior Installation Instructions
CJ-7 YJ BRCJ76R BRCJ81R REAR KITS: BRYJ87R Jeep Wrangler CJ-7/YJ BedRug Interior Installation Instructions Congratulations on choosing the finest interior flooring kit available for your Jeep. BedRug material
More informationMYRIAD Banner Stand is a trademark of Skyline Exhibits. Patent Pending PN32294-B. MYRIAD Banner Stand
is a trademark of Skyline Exhibits Patent Pending 1.1 1. Banner Stand Setup 1.1 Remove banner stand from standard case or Arrive Portable Display & Workstation and assemble pole. 1.2 Insert pole into base
More informationINSTALLATION INSTRUCTIONS for folding arm awnings
Custom made Awnings and Blinds Item No 0757 INSTALLATION INSTRUCTIONS for folding arm awnings IMPORTANT INFORMATION BEFORE INSTALLING YOUR Updated 08/09/15 AN AWNING INSTALLATION IS A HOME IMPROVEMENT
More informationINSTALL INSTRUCTIONS for VEHICLES
INSTALL INSTRUCTIONS for VEHICLES Issued: 1 st December 2011 These are the recommended steps for installing One Way Vision (OWV) film onto a vehicle rear windscreen or side glass panels. Location: Applicable
More informationTermination Procedure LC 1.6mm & 2.0mm Connectors: 1060XX Series
Connector Piece Parts LC Simplex Connector Boot LC Duplex Connector LC Connector CriMp Tulolng LC Duplex Clip Boot 86001-0110, Rev. B USN30MFO/5/2010 Procedure Chart Procedure Tool Required Tool Part Number
More informationBigStack. Minimum Crossbar spread 24 For factory racks: Check fitlist notes, or Yakima.com for your vehicle s crossbar spread.
BigStack Minimum Crossbar spread 24 For factory racks: Check fitlist notes, or Yakima.com for your vehicle s crossbar spread. HEAVY Duty strap (2x) PAD (4x) ADJUSTMENT KNOB (2x) T-BOLT (2x) BAIL (2x) BigStack
More informationCAPRI PLUS. Instruction Manual. 28' x 38' Including sidewall and connector instructions.
CAPRI PLUS Instruction Manual 28' x 38' Including sidewall and connector instructions STOP Prior to installing any tent, always make sure you check for overhead and underground obstructions! For safe assembly,
More informationOperating Instructions
A) ORIENTATION View capsule filling video online at www.profiller.com Cam Lever 1. Place Caps Tray onto Filler with Position I and II markings in front. Check that Cam Lever is set to 3 o clock. 2. Pour
More information2522 and 2523 Fiber Optic Splice Organizer Tray
2522 and 2523 Fiber Optic Splice Organizer Tray Instructions February 1996 Issue 1, 34-7039-6256-2 1 Table of Contents 1. General... 3 2. Kit Contents... 3 3. Available Kits and Accessories... 4 4. Tray
More informationSuggested Installation Instructions for: , Embroidered Front End Mask
I I 1 Suggested Installation Instructions for: 602-246, 1975-1979 Embroidered Front End Mask 2-Cover Hooks 4-Air Foil Inserts 2-2" "U" Shaped Trim Locks 4-2" ADHESIVE BACKED Hook Strips 2-14" ADHESIVE
More informationBRJK11F2, BTJK11F2, BRJK07F2, BTJK07F2, kit
BRJK11F2, BTJK11F2, BRJK07F2, BTJK07F2, FRONT KITS: BRJK07F4, BTJK07F4 Jeep Wrangler JK BedRug/BedTred Interior Installation Instructions Congratulations on choosing the finest interior flooring kit available
More informationButler Personnel Parachute Systems, LLC
Butler Personnel Parachute Systems, LLC 1820 Loudon Avenue NW PO Box 6098 Roanoke, VA 24017-0098 (540) 342-2501 (540) 342-4037 (FAX) Info@butlerparachutes.com Butler Personnel Parachute Systems Back Pack
More informationPreparation. BEDRUG, INC. n 635 Old Hickory Blvd, Old Hickory, TN n n bedrug.com
BRJK07F4, BRJK07F2, FRONT KITS: BTJK07F4, BTJK07F2 Jeep Wrangler JK BedRug/BedTred Interior Installation Instructions Congratulations on choosing the finest interior flooring kit available for your Jeep.
More informationOPERATOR INSTRUCTION MANUAL INCLUDING REPAIR PARTS FOR MODULAR GENERAL PURPOSE TENT SYSTEM (MGPTS) TYPE I
OPERATOR INSTRUCTION MANUAL INCLUDING REPAIR PARTS FOR MODULAR GENERAL PURPOSE TENT SYSTEM (MGPTS) TYPE I Johnson Outdoors Gear, Inc. Eureka! branded tent products 625 Conklin Road Binghamton, NY 13903
More informationWARNING: IMPROPER INSTALLATION WILL RESULT IN LINER FLYING OUT OF THE TRUCK. FOLLOW INSTRUCTIONS EXACTLY
Preparation Instructions Part Number(s): Multiple Kit Contents Item # Qty Req'd Description 1 1 BedTred Floor Panel 2 1 BedTred Bulkhead Panel 3 2 BedTred Sidewall Panels (L&R) 4 1 BedTred Tailgate Panel
More informationSeries 2050 Garden Window Frequently Asked Questions
1. What is the difference between new construction and retrofit? The difference is in the overall jamb depth and required components: For new construction, the flash flange on the head of the unit is left
More informationGeneral Canopy Folding and Packing Instructions for H-X Series Personnel Parachute Canopies. Manufactured by Butler Parachute Systems, Inc.
General Canopy Folding and Packing Instructions for H-X Series Personnel Parachute Canopies Manufactured by Butler Parachute Systems, Inc. Issued 24 July 1998 This set of instructions is for the routine
More informationOWNER S MANUAL. Version /2011 TEAL CAMPER OWNER S MANUAL. copyright Teal International Corporation
OWNER S MANUAL Version 1.1-11/2011 INDEX Introduction.... 3 Camper Shell Assembly.... 4 STEP 1 - Floor Board... 5 STEP 2 - Panel Assembly...................6 STEP 3 - Door Frame Assembly... 8 Popup Roof...
More information4.2 Assembly Instructions
4.2 Assembly Instructions 4.2.1 Assembly of Reserve Canopy. Assembly of Reserve Canopy using Rapide Links. After inspecting the Parachute and the Wings Harness/Container System, hang or lay the parachute
More informationHow to make an inflatable cube
How to make an inflatable cube Beta instruction manual produced by Tools for Action. First Edition November 2015. Paris. Second Edition March 2016. Materials & Tools Mylar insulation foil (we use Parotec
More informationSYSTIMAX RoloSplice Multiple Splice Organizer Installation
SYSTIMAX RoloSplice Multiple Splice Organizer Installation General This instruction sheet provides procedures for installing the SYSTIMAX RoloSplice, multiple splice organizer management system and is
More informationFISH CAT SCOUT OWNER S MANUAL
FISH CAT SCOUT OWNER S MANUAL ALWAYS WEAR A COAST GUARD APPROVED FLOTATION DEVICE WHEN OPERATING THE FISH CAT SCOUT. Know the limits of your abilities and the limits of your equipment. Changes in air temperature
More informationWritten By: Brittany McCrigler
Installing a Zipper in a Patagonia Fleece Jacket Replace the zipper in your fleece jacket. Written By: Brittany McCrigler ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION [video: https://vimeo.com/48376830]
More informationDURA WHEEL CHAIR LOCKER ASSEMBLY INSTRUCTIONS
DURA WHEEL CHAIR LOCKER ASSEMBLY INSTRUCTIONS 1. Locate a Frame and Door: Start by locating a frame and door. 2. Front Frame: Now stand up the frame and door in the desired assembly area. 3. Exterior Wall:
More informationPR-429BF-600M. Bell 429 Blade Fold Kit Operations Manual
Table of Contents Table of Contents... 1 Record of Revisions... 2 References... 3 Introduction... 4 Contact Information... 4 Prerequisites... 5 First Time Use... 6 Blade Clamp Placement... 6 Blade Clamp
More informationOwner s Manual & Installation Instructions. Model 900XT & 1000XT Awnings
Owner s Manual & Installation Instructions Do Not Discard, Retain for Future Reference Model 900XT & 1000XT Awnings WARNING: Failure to Follow These Instructions Could Result In Personal Injury! For Technical
More informationINSTALLATION INSTRUCTIONS for automatic awnings
Custom made Awnings and Blinds Item No 0756 INSTALLATION INSTRUCTIONS for automatic awnings AUTOMATIC AWNING IMPORTANT INFORMATION BEFORE INSTALLING YOUR AUTOMATIC AWNING Updated 08/09/15 AN AWNING INSTALLATION
More informationJOINING MULLION (DIRECT MULL) ASSEMBLY INSTRUCTIONS FOR 3-WAY OR 4-WAY JOINTS FOR IMPERVIA AWNING, CASEMENT AND LARGE AWNING
2014 Pella Corporation JOINING MULLION (DIRECT MULL) ASSEMBLY INSTRUCTIONS FOR 3-WAY OR 4-WAY JOINTS FOR IMPERVIA AWNING, CASEMENT AND LARGE AWNING For Additional Mullion Assembly Information; Visit www.installpella.com/mullions,
More informationColor Light Streams Lighted Bubbler Spillway Pot (CLSDLP) Installation Manual
Color Light Streams Lighted Bubbler Spillway Pot (CLSDLP) Installation Manual 27.75 23.75 25.50 20.75 Specifications: 8-13 GPM 12-14 VAC only (Class 2 transformer required) 3W max. 100 ft. cord, conduit
More informationPlease read this guide carefully. It tells you how to prepare your cutting plotter for production use in a few easy steps.
OPERATING GUIDE for Secabo mini Cutting Plotter Congratulations on purchasing your Secabo mini cutting plotter! Please read this guide carefully. It tells you how to prepare your cutting plotter for production
More informationCabinet Mount Assist Lift n Lock Instructions
Cabinet Mount Assist Lift n Lock Instructions PART LIST 2 @ Gas Cylinder 1 @ Lock Bar 2 @ Rubber Sleeve (preset) 4 @ Stopper Pin (2pcs preset) 4 @ Saddle Block 8 @ 19mm Black PVC Cap 5 @ 14mm Black PVC
More information* * KR54-F, KR9854 & KR9954 Installation Instructions. Read All Warnings Before Starting Installation! Index:
*941061-00* 941061-00 Keyed Removable Mullion KR54-F, KR9854 & KR9954 Installation Instructions CLASSIFIED CLASSIFIED C Read All Warnings Before Starting Installation! Index: General Information ----------------
More informationZippers, Zippers, and More Zippers with Donna Cash
Zippers, Zippers, and More Zippers with Donna Cash Let s talk about closure, closure with zippers! In this class you will learn all about the different types of zippers and how to insert these in a variety
More informationProduct instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E
Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E The Trimfast Ream Cutters are reliable, high performance cutters that will give you the results you need quickly
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationFEATHER-LITE ROOF TOP TENT SET-UP GUIDE
FEATHER-LITE ROOF TOP TENT SET-UP GUIDE TENT031 INSTALL TIME: 30 minutes 0 GET ORGANIZED you will need: D Your Tent D The Ladder (in a separate box) D A Power Drill w/ Phillips screw bit D A solid, scratch
More information3 Nomad Scraper Matting 9100 (formerly 3M Entrap Recessed Well Matting)
3 Nomad Scraper Matting 9100 (formerly 3M Entrap Recessed Well Matting) Technical Data/ Product Specifications 1.0 Product Description The product is a durable, all-vinyl floor mat having an open, continuously
More informationSTEALTH PRO OWNER S MANUAL
STEALTH PRO OWNER S MANUAL ALWAYS WEAR A COAST GUARD APPROVED FLOTATION DEVICE WHEN OPERATING THE STEALTH PRO. Know the limits of your abilities and the limits of your equipment. Changes in air temperature
More information3 Nomad Scraper Matting 8100
Technical Data/ Product Specifications 3 Nomad Scraper Matting 8100 (Replaces 3M Nomad Heavy Traffic and Extra Duty Unbacked Matting) 1.0 Product Description The product is an unbacked, non-woven, open
More informationFibreGuard Closure with SLIDE-N-LOCK Fiber Management
DECEMBER 2008 FibreGuard Closure with SLIDE-N-LOCK Fiber Management PREPARATION Express Fiber Cable 1. From the expressed cable loop, identify and select the loose buffer tube with the fibers required
More informationCrimp & Cleave Termination Instructions
Your Optical Fiber Solutions Partner Crimp & Cleave Termination Instructions for 200 µm Harsh Environment SMA For Use With: 200 µm HE SMA Termination Kit 200 µm HCS Fiber-Optic Cable HE SMA 200 µm Crimp
More informationHonda Ridgeline Installation Instructions
Honda Ridgeline Installation Instructions READ THIS... If you read these instructions from beginning to end before starting you will probably not need to look at them again during the installation, but
More informationKAWNEER 1786 RIM EXIT DEVICE
FEBRUARY, 2015 1 DOOR STILE Device C L 40" 41-9/32" Cylinder C L Bottom of door RIM EXIT DEVICE LOCATION DOGGING KEY EXIT DEVICE FILLER PLATE CYLINDER & CYLINDER RING HOUSING COVER CYLINDER INSTALLATION
More informationTabletop Kit 01. features and benefits: dimensions: additional information:
Tabletop Kit 01 TK-TTK-01 Make a statement with an easy-to-assemble tension fabric Hopup tabletop display with spotlights. A custom-printed stretch table throw that fits standard 6ft tables & a single-sided,
More informationASSEMBLY & CARE INSTRUCTIONS
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 3 9 Part No. FT3711 - on road FT3923 - off road OPTIONAL SUNROOM Wall and floor kit Part No. FT3723 - on road FT39 - off road OPTIONAL SPARE ROOM Roof,
More informationInstallation Guide Cable
Installation Guide Cable Thank you for selecting a DuctSox System. This guide will be helpful for the installation of a Cable System. Sections of fabric will be labeled, assembled, bagged, and boxed for
More informationBowDown. MiniMuM Crossbar spread 24 (61CM) Steel Hook (2X) Buckle Strap (2X) Plastic Tube (2X) Plain Strap (2X) SHORT BLACK T-BOLT (2x) BOWDOWN (2x)
BowDown MiniMuM Crossbar spread 24 (61CM) Heavy Duty strap (2x) SHORT BLACK T-BOLT (2x) BOWDOWN (2x) Bow Stern Tie Down Buckle Strap (2X) Plastic Tube (2X) Plain Strap (2X) Steel Hook (2X) IMPORTANT WARNING
More informationTuf-Lite and Tuf-Lite II Fans 6000 Series Hub
Tuf-Lite and Tuf-Lite II Fans 6000 Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 32 and 33 Diameter Hudson Tuf-Lite and Tuf-Lite II fan blades Hudson Tuf-Lite (black) fan blades are made
More informationSAFETY GUIDELINES FOR DIY TENTS
SAFETY GUIDELINES FOR DIY TENTS Please read carefully and fully before starting assembly of the tent 1. The installer is solely responsible for evaluating the site and proper securing method determined.
More informationASSEMBLY & CARE INSTRUCTIONS. 7 x4 TRAILER TENT SERIES 4 9. OPTIONAL SUNROOM Wall and floor kit. OPTIONAL SPARE ROOM Roof, wall and floor kit
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 9 Part No. TM709 OPTIONAL SUNROOM Wall and floor kit Part No. TM723 OPTIONAL SPARE ROOM Roof, wall and floor kit Part No. TM76 Please keep these instructions
More informationThe Hot Mess Casserole Carrier Skill Level: Intermediate
The Hot Mess Casserole Carrier Skill Level: Intermediate Designed By Sara Lawson Sewn By Sara Lawson www.sewsweetness.com This casserole carrier is the perfect companion to your on-the-go meal. It conveniently
More informationINSTANT GARAGE MODEL NO: CIG81224 ASSEMBLY INSTRUCTIONS PART NO: ORIGINAL INSTRUCTIONS
INSTANT GARAGE MODEL NO: CIG81224 PART NO: 3503578 ASSEMBLY INSTRUCTIONS ORIGINAL INSTRUCTIONS GC1117 INTRODUCTION Thank you for purchasing this CLARKE Instant Garage. When erected, the CIG81224 garage
More informationSeries SSG and Captured corner mullion. Installation Instructions
Series 5500 SSG and Captured corner mullion Installation Instructions Part NO. Y556 February 2013 SECTION TABLE OF CONTENTS S-5500 SSG and Captured Corner Mullion Installation Instructions PAGE I. General
More informationKontrol Kube Advanced Owners Manual
Mobile Containment. Simplified. TM Kontrol Kube Advanced Owners Manual KONTROL KUBE www.kontrolkube.com 800.343755 1 IMPORTANT SAFETY INFORMATION SAVE THESE INSTRUCTIONS. CAREFULLY READ AND FOLLOW THESE
More informationFyre-Stones Set C Installation Instructions (sku )
Items Required ¼ Crushed Glass (see page 14 for quantities): -- Platinum (94500580) -- Reflective Bronze (94500581) -- Cobalt (94500582) Compatibility 33 DVI DVL GSR NB with Dancing-Fyre Burner 864 HO
More informationfunctionality with the necessary maintenance tools stored in a convenient built in tool box, as well as parallel handles for
GuilloMax User Manual The Guillomax has distinct features such as its unique structure and ease of cutting. It combines symmetry with functionality with the necessary maintenance tools stored in a convenient
More informationBIOMASS STOVE SAFETY PROTOCOL GUIDELINES
BIOMASS STOVE SAFETY PROTOCOL GUIDELINES The process of designing stoves should include evaluation of safety. Seeing that there was no published standardized methodology for evaluating stove safety, Nathan
More information4-foot Economy Sign Post. 4-foot post is rated at 2 pounds per foot. 7-foot Economy Sign Post
Introduction: ComplianceSigns.com offers a variety of sign posts, sign mounting hardware, sign bases, mounting tape and more to mount your safety signs indoors or out. We offer three styles of sign posts,
More informationTOYOTA TUNDRA BEDRUG Preparation
TOYOTA TUNDRA 2007 - BEDRUG Preparation Part Number(s): PTS12-34070 (5.5 bed) PTS12-34071 (6.5 bed) PTS12-34072 (8.1 bed) NOTE: Part number of this accessory may not be the same as the part number shown.
More informationAssembly instructions for Eurotramp trampolines Series: Ultimate, Grand Master Exclusiv, Grand Master, Master
Assembly instructions for Eurotramp trampolines Series: Ultimate, Grand Master Exclusiv, Grand Master, Master 1. Assembly instructions 2. Attaching the plastic coated steel cables on the Ultimate frame
More informationESTES INDUSTRIES 1295 H Street Penrose, CO PRINTED IN CHINA BLACK ENGINE HOOK RETAINER RING (1) (30160) KEY
COUNTDOWN AND LAUNCH #2190 www.estesrockets.com KEY ALWAYS OUT UNTIL FINAL COUNTDOWN! 1... 10" (25.4 cm) 2... 3... ESTES INDUSTRIES 1295 H Street Penrose, CO 81240 PRINTED IN CHINA TIP: Read all instructions
More informationProfessional Mandoline Manual. Model: 90757
Professional Mandoline Manual Model: 90757 Introduction Your MIU France Composite Mandoline features a selection of blades with variable thickness adjustments which make it one of the most versatile kitchen
More informationInstallation Instructions for the Rolltec Adalia X3M Extenda Awning
Installation Instructions for the Rolltec Adalia X3M Extenda Awning Questions? Call Rolltec at 1-800-667-0474 General Tool Requirements Table of Contents Available installation brackets Side dimensions
More informationCrimp & Cleave Termination Instructions for 200 µm Harsh Environment SMA
Your Optical Fiber Solutions Partner Crimp & Cleave Termination Instructions for 200 µm Harsh Environment SMA For Use With: 200 µm HE SMA Termination Kit 200 µm HCS Fiber-Optic Cable HE SMA 200 µm Crimp
More informationSOLHARO ASSEMBLY & INSTALLATION INSTRUCT IONS
A. Introduction: SOLHARO ASSEMBLY & INSTALLATION INSTRUCT IONS Rev. 01/30/2012 The Solharo is an external, retractable, tensioned sun shading system designed to fit over a sunroom or wood pergola. The
More informationInstallation Instructions for the Rolltec Physique XL Awning
Installation Instructions for the Rolltec Physique XL Awning Questions? Call Rolltec at 1-800-667-0474 General Tool Requirements Table of Contents Available installation brackets Side dimensions of various
More informationButler Tactical Parachute Systems, LLC
Butler Tactical Parachute Systems, LLC A division of Butler Parachute Systems Group, Inc. TT-600 TETHERED TANDEM BUNDLE DELIVERY SYSTEM ASSEMBLY MANUAL (Revision A) Page 1 of 40 INTRODUCTION This manual
More informationEmergency Parachute Manual
National Parachute Industries, Inc. PO Box 245 - Palenville, NY 12463 - USA PH 908-782-1646 FAX 908-782-5638 E-mail info@nationalparachute.com Emergency Parachute Manual Seat Supplement National 360-S,
More informationINSTALLATION INSTRUCTIONS for vertical awnings
Custom made Awnings and Blinds Item No 0759 INSTALLATION INSTRUCTIONS for vertical awnings IMPORTANT INFORMATION BEFORE INSTALLING YOUR Updated 08/09/15 AN AWNING INSTALLATION IS A HOME IMPROVEMENT PROJECT
More informationSolera Family and Screen Room. Installation and Owner s Manual (For Aftermarket Applications) Table of Contents
Solera Family and Solera Family and Installation and Owner s Manual (For Aftermarket Applications) Table of Contents Introduction 2 Preparation 2 Resources Required 2 Installation 3 Install Upper Brackets
More informationNotes, Parts List & Drawings
Biomass Chopper/Cutter Notes, Parts List & Drawings Page 1 of 16 The Easy BioChop biomass chopper/cutter was designed to cut both wet and dry biomass and to accomplish a number of goals. The objectives
More informationFLEX KEY ASSEMBLY. ..._ o RAFTER ARM TUBE MAIN ARM TUBE CAP NUT CLAW HINGE
ZIP DEE Inc. 96 Crossen Ave. Elk Grove Village, IL 60007(847)437-0980 (800)338-2378 HEAD CASTING AWNING RAIL FLEX KEY ASSEMBLY..._ o GM1 Installation Instruction GMC Motorhome RAFTER ARM TUBE MAIN ARM
More informationButler Tactical Parachute Systems, LLC TT-600 TETHERED TANDEM BUNDLE DELIVERY SYSTEM. ASSEMBLY MANUAL (Revision D) 18 FEB 2009
Butler Tactical Parachute Systems, LLC A division of Butler Parachute Systems Group, Inc. TT-600 TETHERED TANDEM BUNDLE DELIVERY SYSTEM ASSEMBLY MANUAL (Revision D) 18 FEB 2009 Page 1 of 42 INTRODUCTION
More informationItem #: BTOT Assembly Instructions
Item #: BTOT Assembly Instructions For our most current instructions, to request missing, lost or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com
More informationINSTALLATION & MAINTENANCE MANUAL SERIES 9000 MODELS 9150/9300 SERIES 9000 VALVES WITH V BALL
BRIEF INTRODUCTION Split body (2-piece) valve allows easy replacement of gasket, seal, and seats without special tools. Series 90D ball valves use floating ball design. Induced by the line pressure the
More informationMODEL DCC DOUBLE WALL CHIMNEY CONNECTOR
Installation & Maintenance LISTED Tested to *UL 103HT & ULC-S641 Instructions MODEL DCC DOUBLE WALL CHIMNEY CONNECTOR A MAJOR CAUSE OF CHIMNEY RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR
More informationREAL VALUE SUNDECK THE ELEGANT SOLAR POWER SOLUTION. Product brochure I Sundeck.
REAL VALUE SUNDECK THE ELEGANT SOLAR POWER SOLUTION Product brochure I Sundeck www.solarworld-uk.co.uk A SYSTEM WITH MANY ADVANTAGES AESTHETICS: elegant in-roof solution CAPACITY: high module yields thanks
More informationBR B Bike Rack Instructions
IMPORTANT NOTE: It is common that vehicles with lids and hatches have a single rear wiper. It is important that you make yourself aware that the wiper cannot be used while the rack is attached to the vehicle.
More informationHUNTCO SITE FURNISHINGS. Double Bike Locker Assembly Instructions HUNTCO SITE FURNISHINGS
Double Bike Locker Assembly Instructions Includes instructions for both handle styles. Padlock Handle with U Lock Box and Keyed Pop Out T Handle SITE FURNISHINGS SITE FURNISHINGS and architectural site
More informationUptown Fire Pit Table
Uptown Fire Pit Table Installation Instructions 1 P a g e Contents Contents..2 Required Tools..3 Placing and assembling the Table. 4 Gas Connection..5 Igniter Installation....6 Locating Propane tank 8
More informationPEAK 1 GENERAL INFORMATION 1.1 THE CONCEPT 1.2 SAFETY 1.3 THE SPEED SYSTEM 2 THE EMERGENCY PARACHUTE 2.1 EMERGENCY PARACHUTE ASSEMBLY
PEAK 1 GENERAL INFORMATION 1.1 THE CONCEPT 1.2 SAFETY 1.3 THE SPEED SYSTEM 2 THE EMERGENCY PARACHUTE 2.1 EMERGENCY PARACHUTE ASSEMBLY 3 ADJUSTING YOUR PEAK 3.1 ADJUSTING THE SITTING POSITION 3.2 ADJUSTING
More informationInstruction Manual Remote Swabbing and Microbiological Sampling and Teflon template tools Version , Rev.0
ASSEMBLY AND OPERATIONAL INSTRUCTIONS The remote swabbing and microbiological sampling tool and the Teflon template tool are shipped partially assembled. Complete assembly instructions are provided below:
More informationADDED PROTECTION FOR SLIDE-OUT ROOMS. Installation. Introduction... 2 Product Overview...2 Component Checklist...3
CAREFREE SIDEOUT KOVER II RV Installation ADDED PROTECTION FOR SLIDE-OUT ROOMS TABLE OF CONTENTS SOKII Shown with Full Case Option Introduction... 2 Product Overview...2 Component Checklist...3 Installation...
More informationCOMBI CRATE MODEL NO: 7000/7001/7002/7003
COMBI CRATE MODEL NO: 7000/7001/7002/7003 Owner s Manual READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE KEEP INSTRUCTIONS FOR FUTURE USE. Carlson Pet Products,Inc 14305 Southcross Drive,Suite 105,
More informationTuf-Lite and Tuf-Lite II Fans 6000M Series Hub
Tuf-Lite and Tuf-Lite II Fans 6000M Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 32.8 or 10 Meter Diameter Hudson Tuf-Lite and Tuf-Lite II fan blades Hudson Tuf-Lite (black) fan blades
More informationWv410 window. Installation Instructions
Wv410 window Installation Instructions Part NO. Y007 February 2014 TABLE OF CONTENTS SECTION PAGE I. Product Description and Limitations..........3 II. General Statements and Definitions........3 III.
More informationInstructions. Fibrlok TM 2670 Multi-Fiber Ribbon Construction Tool. November, B
Instructions Fibrlok TM 2670 Multi-Fiber Ribbon Construction Tool November, 1998 34-7032-7181-6-B Contents: 1.0 General... 3 2.0 Ribbon Construction Tool Kit...3 3.0 Preparing the Fibers...3 4.0 Arranging
More informationTAKE EVERY PRECAUTION TO PREVENT CONTACT WITH SKIN OR HAIR!!!
Rev. 1 Rev. Date 5/31/2018 Seat Insert Instructions _ You have purchased the safest and easiest to use seat insert kit available. Please read these instructions and review the images carefully before starting
More information80070 TOP MOUNT CAMPER SHELL and TRANSIT CONNECT RACK TMCS_3:1
ASSEMBLY INSTRUCTIONS for : 80070 TOP MOUNT CAMPER SHELL and TRANSIT CONNECT RACK TMCS_3:1 (916) 638-8703 (800) 343-7486 11261 Trade Center Drive Rancho Cordova, CA 95742 www.kargomaster.com Transit ASSEMBLY
More informationRAFTER VI. Installation and Operation CAREFREE WITH AUTOMATIC AWNING SUPPORT. RV Accessory PRODUCT OVERVIEW
CAREFREE RAFTER VI RV Accessory WITH AUTOMATIC AWNING SUPPORT Installation and Operation PRODUCT OVERVIEW The gives the awning user the ability to easily tighten the center fabric when the awning is extended.
More informationFilm-Tech. The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment.
Film-Tech The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment. These manuals are designed to facilitate the exchange of information related to cinema
More informationModel 205 Fireview Maintenance Kit
Model 205 Fireview Maintenance Kit Please read all of the instructions before you begin the procedure. Confirm that you have all the necessary tools and parts required. Allow about one hour to complete
More informationINSTALLATION INSTRUCTIONS AND OWNER'S MANUAL AWNINGS. For trailers & motor homes with straight sides TOOLS REQUIRED
AWNINGS INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL For trailers & motor homes with straight sides TOOLS REQUIRED 1/4" electric drill Ratchet handle kit 3/8" & 7/16" socket No. 1 and No. 2 screwdriver
More informationHARD DOOR UPGRADE KIT
RV Accessories OWNER'S MANUAL HARD DOOR UPGRADE KIT FOR ADD-A-ROOM & BREEZEWAY SCREEN ROOMS THIS MANUAL SUPPLEMENTS THE ADD-A-ROOM INSTRUCTIONS TABLE OF CONTENTS First Time Assembly... 2 Assembling the
More informationFS-14R Parachute Packing Instructions
United States Department of Agriculture Forest Service Technology & Development Program 5700 Aviation June 2008 0857 2835P MTDC FS-14R Parachute Packing Instructions FS-14R Parachute Packing Instructions
More informationX-SERIES 10x10 SETUP INSTRUCTIONS
SETUP INSTRUCTIONS THANK YOU FOR PURCHASING A 10x10 X-SERIES TENT! If you have questions about installation, maintenance, or take down, please call us at (800)426-9496. Our goal is that you are completely
More information