Transcription

1 Northern Leisure Group Ltd wwwkiddyridesukcom OPERATORS HANDBOOK Manufactured in the UK by Northern Leisure Group Ltd 2016 Spin Master All Rights Reserved Serial No Born On: Northern Leisure Group Ltd/Kiddy Rides Tel: +44 (0)

2 CONTENTS Introduction 1 Fault Finding 19 Safety Matters Initial Inspection Initial Operation Siting Your Ride Daily Checks Taking Care Of Your Ride Standard Operation & Adjustments Control Box / Timer Ride Time Volume Settings Price Of Play Switch Settings Contact Procedures Orders Spares Repairs Hours of Business Ride History / Log Your Notes Declaration Of Conformity Composite Data Sheet 20 21, ,27 Inspection Hatches Inspection & maintenance of components 9 Coin Mechanism Cleaning Installation and Removal 10 Wiring Schematics 11 Wiring Loom Reference 12,13 Plugs & Connections 14 Base Mechanism Components 15 Parts List 16,17 Removal Of Bodyshell 18

3 INTRODUCTION Thank you for purchasing your new children s coin operated ride from Northern Leisure Group Ltd / Kiddy Rides! We trust it will give you many years of profitable service! Established in 1986, the Northern Leisure Group of companies is the UK s leading independent operator, dealer, manufacturer, and distributor of children s coin operated rides Our extensive experience in a wide range of electronic entertainment products has allowed us to offer the ultimate in choice, safety and quality Complete customer satisfaction is what motivates us Being independent allows us to nurture this goal ultimately giving thousands of children and parents world-wide, the assurance that they are in a safe, clean, and fun environment Kiddy Rides supplies a wide range of children s rides for sale, income share, or on a fixed rental basis As well as supplying the rides, it is responsible for unbeatable after-sales support and service for all Kiddy Rides customers as well as other operators Our equipment has been manufactured to the highest standard of construction and safety in order to conform to the HSE Fairground and Amusement Parks, A Code of Safe Practice and the UK Health and Safety at Work Act 1974 All our rides have undergone thorough examinations, and come with a 12 months ADIPS certification of conformity The guidance in this manual is relevant to the safe operation of children s rides wherever they may be operated NORTHERN LEISURE GROUP LTD UNIT 4 KINGSMARK COURT INTERCITY WAY SWINNOW LEEDS LS13 4PN UNITED KINGDOM TEL: +44 (0) FAX: +44 (0) info@kiddyridesukcom wwwkiddyridescouk 1

4 Safety Matters Northern Leisure/Kiddy Rides is a registered Inspection Body of ADIPS (the Amusement Device Inspection Procedure Scheme), conducting independent examinations and certification of children s coin operated rides in accordance with guidance published by the Health and Safety Executive (HSE) By independent, we mean we are not linked to any particular manufacturer and will apply the guidance with equal diligence, regardless of the type of ride, or it s manufacturer Remember, our aim is to help you comply with the HSE guidelines Because of the young age of those who enjoy coin operated children s rides (kiddie rides), safety should be of paramount importance to operators There is surely a moral duty to safeguard the children that use our industry s products Safety doesn t just happen however, it requires commitment from manufacturers, operators and inspectors to ensure high standards As an operator it is your duty to make yourself aware of safety requirements, especially as failure to comply can lead to injury to children, and furthermore, prosecution By adopting a few simple procedures and having annual safety checks performed on your rides, you can show yourself to be conforming with HSE and Local Authority guidelines Also you will gain peace of mind knowing that you have taken active steps to minimize the risks to young children who use your rides It is not always easy to find out exactly what is required of an operator However there are strict guidelines laid down by BACTA (British Amusement and Catering Trade Association) entitled Kiddie Rides; A Safety Guide It is produced by a committee of BACTA members, some of whom represent manufacturers of kiddie rides themselves The guide is fully endorsed by the HSE In an attempt to highlight the importance of safety within the industry, ADIPS has been integrated into the BACTA guidelines This initiative sets out procedures which must be observed by registered Inspection Bodies Furthermore, ADIPS is unified with the HSE Fairground and Amusement Parks Code of Safe Practice To comply with this, a ride must undergo a thorough examination, and documentation must be issued, be retained, and be available for inspection by the Health and Safety Inspectorate and/or an officer of the Environmental Health Department of the local authority Thorough examinations must be carried out at least every fourteen months (annual examinations are recommended) Certification of rides by approved inspectors will give responsible operators within our industry the credibility they deserve An ADIPS certificate is a badge of excellence, ensuring you have taken all the necessary steps to ensure danger risks are kept to a minimum In the past, inspections of children s rides by the HSE appeared to be taking place in response to safety related incidents However, this is changing rapidly, and it would appear random tests are under way Inspectors requesting ADIPS documentation after a safety related incident is likely to become standard practice So, safety first Don t wait for an accident to happen before you consider the safety of your rides, get them ADIPS tested now Call +44 (0) enquiries@kiddyridesukcom Amusement Device Inspection Procedures Scheme 2

5 INITIAL INSPECTION Upon arrival of the machine, it is important to check the following items: a Damage to external packing b Physical damage to the ride c Correct documentation is present d Ride Serial Number e Correct main s voltage rating f Coin mechanism currency and credits Any damage or discrepancies should be reported to your supplier immediately INITIAL OPERATION a Read the operators manual fully prior to operating the ride b Prior to connecting the machine to the mains supply, ensure that it corresponds to the supply rating, which should be stated on a sticker or plate on the rear of the base close to the mains cable outlet c Upon power up, the lights on the buttons and outer body should illuminate, and begin to flash An audible message may also be heard stating the ride model and version d Insert the correct coinage for the operation of the ride, after which the start button will flash, and / or an audible prompt will be heard for you to press the start button e Press the start button and the ride will begin to operate All lights will flash or illuminate and music will begin to play Check the volume is set to a desired level Press the feature buttons in turn, and the appropriate sound effect or interaction will take place ( please note, each feature must have completed its cycle before another feature can be activated) f Whilst the ride is in operation, check that everything is working correctly, and that there are no unusual noises or vibrations When the ride has operated for the pre set duration (usually around 90 seconds) the ride will automatically stop A farewell voice message may be heard, and the ride is once again ready to accept coins g Make a note of the rides serial number This is located on the silver manufacturers plate at the rear of the ride The serial number gives access to essential details of your machine, including your machines parts and history 3

6 SITING THE RIDE The following conditions must be observed when siting the machine: a The machine must be placed on level ground which is firm and free from any holes etc Where possible, a non-slip surface would be recommended b The ride is designed for protected locations The ride should not be sited in any area where it would be subjected to water splash The ride, in some circumstances, may be sited outdoors under a canopy, which will protect it from rain, although this is not recommended c The machine should be connected to a Residual Current Device (RCD socket) d The ride should be sited clear from any obstruction The manufacturer recommends that the machine is sited with a minimum of 2ft (610mm) clearance all around and away from any other obstruction or item of equipment e The ride should be situated as close as possible to the power source, and the mains cable must be safely secured and protected, to eliminate any risk of tripping or damage f The ride should not be sited in an area where it may cause an obstruction g Always ensure that the mains plug is accessible, so that the mains power may be isolated in an emergency 4

7 DAILY CHECKS A check of each coin-operated Kiddy Ride should, whenever reasonably practical, be carried out each day before it is made available for public use The following checks are recommended: a Check that the mains plug is undamaged and securely attached to the mains cable, with no visible wires b Check the mains cable itself has no damage c Make sure there are no broken, damaged or sharp parts of the ride which may cause injury d Check that all covers and guards are in place thus preventing any access to the rides mechanism e Ensure there is no unusual excess wobble or play from the ride f Make sure all advisory literature is in place g Ensure the area around the ride is free from obstruction and that persons passing by are not in any danger h The ride should be kept clean and free from any customised additions unless approved by the manufacturer i Insert coins and run the ride to ensure everything is operating correctly If as a result of the above visual checks any doubt arises, then the company, supplier, or person responsible for the ride should be notified immediately 5

8 TAKING CARE OF YOUR RIDE All Northern Leisure Group Ltd rides are manufactured in the UK using a high quality Lead Free self coloured GRP This material can be maintained easily, and kept to a very high standard by taking day to day care of your ride CLEANING To ensure you get the maximum life span from your machine, a day to day clean is recommended Clean the main areas of the ride with a damp cloth rinsed out in soapy water Ensure the cloth is not drenched in water and avoid any electrical components such as coin-mech, lights, buttons etc Do not hose down or flood the machine! Alternatively, a household furniture polish can also be used, or in cases of an extremely dirty ride, Kiddy Rides recommend using a good automotive cleaning compound This material is available through Northern Leisure / Kiddy Rides Do not use any solvent based materials when cleaning your ride COIN MECHANISM The Coin Mechanism, or Coin Mech is located on the rides dashboard in the cockpit area Access for the coin mech is gained by opening the lock on the metal face plate, and simply lifting it out towards yourself The mech and connection can now be easily inspected or cleaned at this point See page 10 6

9 Standard Operation And Adjustments Control Box / Timer - The control system in this ride is a Kermit Navigator box This is located behind the rear door on the ride, it is accessed by removing the 2 bolts using a 4mm hex/allen key Once the door is removed, it leaves the Kermit Box, and its connections easily accessible If required, the box can be removed from the ride by removing the two small allen bolts which hold the mounting tags using a 25mm hex key Once the bolts are removed, simply pull the box upwards disengaging the lower mounting tag *Ensure all connections to the Kermit Box are disconnected before removal Ride Time - The length of time that each ride lasts is pre-programmed, and can not be changed The standard length for each ride is approximately 90 seconds Volume Settings - (The power must remain on, and the ride should be running to adjust the volume settings on this control system) The volume control buttons are located on the right hand side of the control box as indicated by the diagram on the box lid There are 2 small buttons (Fig1), the top one increases the volume (+), and the one beneath it decreases the volume (-)These are used to adjust the level of the soundtrack or theme music They also adjust the volume level for the pushbutton sound effects To adjust the level of these, the volume buttons must be pressed when a pushbutton has been activated and the sound effect can be heard Please note: The pushbutton must be pressed and the sound effect must be playing in order to adjust the volume Fig 1 General & Pushbutton Volume controls 7

10 Standard Operation And Adjustments PRICE OF PLAY - The price of play is the cost of each turn on the ride, eg 1 ride for 50p The cost per ride and currency is set at manufacture, and the operator s preference must be stated at the time of purchase However, if you find it absolutely necessary to have these settings changed at a later date, then it is possible Simply set the switch bank to the desired configuration Please refer to the table below The switch bank is located next to the volume controls (see fig2) Contact the manufacturer for any support or advice *Please note that the rides power must be off when changing any switch settings The power should then be switched back on, once completed, for any changes to take effect PRICE OF PLAY SW1 SW2 SW3 SW4 PRICE/CREDITS 20/1, 50/3, 100/7 PRICE/CREDITS 30/1, 50/2, 100/5 PRICE/CREDITS 50/1, 100/3, 200/7 PRICE/CREDITS 200/1, 500/3 PRICE/CREDITS 80/1, 200/3, 300/7 PRICE/CREDITS 100/1, 200/3, 400/7 PRICE/CREDITS 150/1, 300/3, 400/5 PRICE/CREDITS 200/1, 300/2, 400/4 PRICE/CREDITS 20/1, No Bonuses PRICE/CREDITS 30/1, No Bonuses PRICE/CREDITS 50/1, No Bonuses PRICE/CREDITS 60/1, No Bonuses PRICE/CREDITS 80/1, No Bonuses PRICE/CREDITS 100/1, No Bonuses PRICE/CREDITS 150/1, No Bonuses PRICE/CREDITS 200/1, No Bonuses OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON OFF ON OFF OFF OFF ON ON OFF OFF OFF ON ON OFF ON OFF ON OFF ON ON ON ON OFF OFF OFF ON ON OFF OFF ON OFF OFF ON ON ON OFF OFF ON ON ON OFF ON ON ON OFF ON ON OFF ON ON ON ON ON Fig 2 Switch Bank 8

11 Inspection of Features & Components Front Red Lamps - Continuously flash when power is on Emergency Lamps - Flash alternately only when ride is in motion Front Hatch - Remove to gain access for inspection of components Rear Hatch - Remove to gain access Rear LED s - Continuously flash when power is on FRONT HATCH The front inspection hatch gives you access to inspect or replace many of the rides features To remove the hatch simply remove the 2 fixing bolts using a 4mm Hex/Allen key The components & features accessed through this hatch include the following: Front Red Lamps - fixings, connections, bulbs Emergency Response Lamps - connections (Bullet Crimps) Light Sequencer - connections, pcb Pushbuttons - fixings, connections, switches, bulbs Speaker - connections, mountings Coinmech Surround - mountings Steering Wheel - fixings, mountings, bearing Meter - connection, mounting (meter can also be inspected by removing coin mech face plate) Wiring Loom/Harness - the front section of the loom, all plugs and connections REAR HATCH The rear inspection hatch gives you access to inspect the electrical connections and the rear body - base fixings (see pg18 for removal of body) To remove the hatch simply remove the 2 fixing bolts using a 4mm Hex/Allen key The components & features accessed through this hatch include the following: Kermit Control Box - connections, volume, fittings Connections - all plugs & loom connections Rear Lights - connections, fixing Rear Fixing Bolts - body-base mountings Character Fixings - fixings for character/marshall Wiring Loom/Harness - back section of loom, plugs & connectors 9

12 ON ECE THE COIN MECH In order to ensure maximum efficiency from your coin mech it is essential to pay regular attention to the cleaning of the coin pathway Before attempting to clean or remove the mech, the machine should be switched off Any cleaning should be carried out by using a soft damp cloth The surface should always be left clean and dry after such cleaning If any drops of water enter the product, leave the machine switched off for sufficient time to dry out before switching the power back on again Never use solvents to clean the mech This will damage the surfaces Note: Failure to switch the machine off before cleaning could result in inconsistent coin acceptance The coin mechanism used is an RM5 Evolution ON ECE RM5 LOAD DIP Switches to be set to OFF position Switches are inactive as settings are determined by the Kermit Control System Power Connection via Ribbon Cable with 10-way plug from Kermit Control Box output REJECT 10 ACCEPT

13 WIRING SCHEMATICS Pushbutton 3 Engine P P5 P Start Lamp Start Button P V Pushbutton 1 Siren 2 TX Pushbutton 2 Horn 3 RX 4 GND P2 Speaker Kermit Navigator P4 1 P10 4 Lamps 3 2 IEC CE22 Mains Inlet M P9 P3 Motor Light Sequencer Filter LED Lamps MAINS IN Meter

14 Top Loom Reference - refer to diagram Colour Ref: Button / Destination: Plug / Pin No: White / Red Horn (switch common) P6 / 2 Purple Horn P6 / 6 Black / Brown Start, Siren, Ignition (switch common) P4 / 6 Pink Start P4 / 19 Green White Siren Ignition P4 / 20 P4 / 21 Colour Ref: Use / Destination: Plug / Pin No: Red Start Lamp + P4 / 18 Brown Start Lamp - P4 / 5 Yellow /Brown Lamps - Buttons, Headlights, Tail Lights P10 / 3 Yellow / Black Lamps - Buttons, Headlights, Tail Lights P10 / 4 Black/White (2-core) Black (2-core) Speaker Speaker P4 / 12 P4 / 13 Blue Meter P4 / 4 White / Orange Meter (+12V) P4 / 17 Colour Ref: Light Sequencer: Yellow Light Sequencer (in) P4 / 22 (SSR+) White / Blue Light Sequencer (in) P4 / 23 (SSR-) White / Black Light Sequencer (in) P4 / 10 Red Light Sequencer (out) Light Sequencer Black Light Sequencer (out) Light Sequencer 12

15 Base Loom Reference - refer to diagram MAINS SUPPLY Colour Ref: Use / Destination: Plug / Pin No: Brown +240V Mains In, Mains Filter Inlet, IEC(Female) Blue -240V Mains In, Mains Filter Inlet, IEC(Female) Yellow / Green Earth Inlet, Ground MOTOR SUPPLY Brown Blue Yellow / Green +240V Supply, Kermit Output -240V Supply, Kermit Output Earth, Kermit Output IEC(Male) IEC(Male) IEC(Male) Mains Supply / Input Out To Kermit Power Input (FemaleIEC) Filter In From Mains Supply (3-Pin 13A Plug) 13

16 Engine Siren Horn Start 4-WAY CONNECTOR - P10 To Lamps PUSHBUTTON CONNECTIONS LED s LIGHT SEQUENCER 13 Black & White Speaker 12 Black Speaker White & Black 23 White / Blue Light Sequencer (Play-) Yellow Light Sequencer (+12V) 8 21 White Pushbutton 2 (Ignition) 7 20 Green Pushbutton 1 (Siren) 6 Black Start Switch 19 Pink Start Button 5 Brown Start Lamp - 18 Red Start Lamp + (+12V) 4 Blue Meter 17 Red & Blue Meter (+12V) PIN No WIRE COLOURS USE PIN No WIRE COLOURS USE 25-WAY CONNECTOR - P4 PAW PATROL - PLUGS & CONNECTIONS P4 - Pin23 P4 - Pin22 P4 - Pin Purple Pushbutton 3 (Horn) White & Red Pushbutton 3 (Common) 1 PIN No WIRE COLOURS USE 15-WAY CONNECTOR - P6

17 Base Components Ref Motor Gearbox Crank Bearing Alloy Crank Block Crank Spacer Description Earth Point Mains Inlet Clamp Mains Lead Protector Gearbox Pulley Motor Pulley Drive Belt Motor Cable Mains Filter Mains Lead Kermit / Control Box Kermit / Control Box Mounting Bolts Kermit / Control Box Mains In (Male IEC) Motor Supply Inlet Base Castors Rocker Cradle Rear Body Mounting Bolts Front Body Mounting Bolts Motor Inspection Cover Motor Output (Female IEC) ,14 15

18 Parts List - Upper Body DESCRIPTION OF PARTS QUANTITY ITEM REF Coin Mech 1 RM5-V00 Coin Mech Mini Face Plate 1 RM5 Mini Face Plate Coin Mech Metal Surround 1 Security Mech Surround Lock 1 Sale Lock Meter / Counter 1 Base Meter Speaker 2 Speaker Speaker Cover 2 KR Speaker Cover Button Round 3 Medium Round Button Button Rectangle 1 Rectangle Lumi Button Button Legends 4 Button Legends Button Wedge Bulb 4 12V 01A Wedge Bulb Emergency Response Lights 2 LED Marker Light Red Front Light 2 Low Profile Button Rear Tail Lights 2 Red LED Steering Wheel 1 Steering Wheel Steering Bearing Block 1 Steering Bearing Block Steering Wheel Spacer 1 20mm Oilite Bush Steering Wheel Fixing 1 M12 Bolt & Nylock Floor Tape 1 Paw Patrol Floor Tape Aluminium Edging/Step Plate 1 Paw Patrol Edging Plate Wiring Loom 1 Paw Patrol Loom KR-005 Character / Dog 1 Marshall 16

19 Parts List - Base Components DESCRIPTION OF PARTS QUANTITY ITEM REF Motor 1 Single Phase Motor Motor Pulley 1 Tec Single Phase Motor Pulley Gearbox 1 RV40 Gearbox Gearbox Pully 1 Paw Patrol Gearbox Pulley Drive Belt 1 Paw Patrol Drive Belt Base Wheels / Towing Wheels 2 MK2 Base Castor Mains Lead Inlet Clamp 1 Mains Conn Clamp Mains Lead (To Plug) 1 Mains Lead Mains Lead Protector 1 Clear Hose Mains Inlet Filter 1 Mains Filter Crank Bearing 1 Crank Bearing Crank Block 1 Crank Block Crank Spacer 1 Crank Spacer Rubber Feet 4 Base Feet Kermit Control Box 1 Kermit Navigator Kermit Power Lead (from filter) 1 Female IEC Lead Motor Lead (from Kermit) 1 Male IEC Lead H Frame Bearing 4 MK2 H Frame Bearing Cash Box 1 MK2 Cash Box Cash Box Lock 1 Sale Lock For replacement Nuts, Bolts, or Fixings, please state the use and location at the time of enquiry 17

20 Ensure the power is turned off before carrying out any of the following procedures! Removal Of Body Shell (2 persons required) To remove the Body Shell from its base you must gain access to the four Body Mounting Bolts The front two are located towards the front of the footwell Remove the dome headed Allen bolts using a 5mm Hex-Allen Key The back mounting bolts are accessed through the rear door on the ride Remove the two Allen Bolts from the hatch using a 4mm hex key and lift the door towards yourself Directly in front of you through the opening is the Kermit Control Box and all it s connections Behind this is the wooden floor of the ride where you will find the two rear bolts Remove the nuts using a 13mm socket or spanner Once all four mountings are removed ensure you disconnect all connections to the Kermit Box Making sure that all wires & connections are unplugged and free from snagging, the body shell can now be removed from the base mechanism by lifting the body upwards *Please note that it is recommended that two or more people should be used to lift off the shell The shell needs to be lifted until the base of the shell is clear of all base components manual handling and lifting guidelines should be followed, as set out by the HSE This can be found by visiting wwwhsegovuk Once the ride is separated, a full inspection of the Base Mechanism can be carried out This level of maintenance should only be carried out by a competent person If care is not taken when inspecting or servicing the ride, there may be risk of damaging components or personal injury 18

21 FAULT FINDING To be carried out by a competent person SYMPTOM CHECK No lights / self test message Coins do not accept Mains voltage supply Mains supply to control box Green 4-way plug on control box 2x yellow wires into 4-way plug Break in connection to yellow wires to lamps Check mains power is on Voltage to coin mech Ribbon Cable disconnected / broken Faulty mech Coins accept but meter / counter does not turn Check connections to meter / counter Check wires on D plug to control box Faulty meter Ride will not start Meter turns when coins are inserted but will not operate the start button prompt when the credit is reached When start button is pressed, sound operates but no movement occurs Emergency Response Lights at front do not flash when ride is going No sound Start Button Connection Faulty Start Switch Control box / D plug Faulty Control Box Motor connection to Kermit Box Broken Drive Belt Loose motor pulley Faulty Motor or Start Capacitor Faulty Kermit Connections are plugged in and secure to the back of the lights Connections to Light Sequencer Faulty Light Sequencer Blown LED s D-Plug connections Check speaker connections Check volume settings D-Plug connections Faulty Speaker For advice and support on any problem, please call our Technical Dpt on +44 (0) or technical@kiddyridesukcom 19

22 Orders, Spares, and Repairs TELEPHONE Call us on +44 (0) Confirm your order by 200pm and we will ship the same day If goods aren t in stock, you will be given an expected shipping date before confirming your order FAX Fax us on +44 (0) Confirm your order by 200pm, and we will ship stock items the same day POST- Northern Leisure Group Ltd Unit 4 Kingsmark Court, Intercity Way, Leeds LS13 4PN, West Yorkshire, United Kingdom Send us an order by post If you don t have an account with us, please include payment for the full amount including delivery and VAT your order directly to orders@kiddyridescouk or browse our web pages at wwwkiddyridescouk and us directly from there METHODS OF PAYMENT Subject to approval, we offer thirty day Credit Accounts Please call for more information If you are not an account holder, you can post a cheque along with your order We would also welcome receiving your payment by BACS direct credit Please contact us for more details Northern Leisure Group also accept payment from all major debit and credit cards Please note that a fee of 3% will be added for credit card payments only If you have any queries regarding an account, then please contact us You can also get information by ing our accounts dept at accounts@kiddyridescouk NO MINIMUM ORDER VALUE We want you to order what you want, when you want it So you can order whatever quantities you like from Kiddy Rides, and you won t be penalized with a minimum order value ON-SITE REPAIRS If you are unable to return parts for repair, or fit spares yourself, we can arrange for one of our regional engineers to make a site visit Just call for details HOURS OF BUSINESS Our office and sales lines are open Mon Fri: 900am to 530pm You can still call our number ( +44 (0) ) outside these hours, and leave a message with our pager service Alternatively, you can contact us by fax or All goods are supplied on the conditions that Northern Leisure shall not be liable for any direct or consequential damage arising from delay in delivery or from defective material, other than is covered by our usual form of guarantee Whilst every effort is made to ensure the accuracy of the particulars contained in this book, modifications and specification changes to kiddie rides are on going These may affect the information specified 20

23 REPAIR, SERVICE, AND HEALTH & SAFETY RECORD To be filled in by Engineer at time of work being carried out DATE PROCEDURE Service / H&S / Repair ENGINEER COMPANY COMMENTS 21

24 CE DECLARATION OF CONFORMITY Manufacturer: Northern Leisure Group Ltd, Unit 4 Kingsmark Court, Intercity Way, Leeds, LS13 4PN, UK Details Of Electrical Equipment Type No: Description: Directives This Equipment Complies With: Harmonised standards applied in order to verify compliance with Directives: 2 Coin Operated Childrens Ride Electrical Equipment (Safety) Regulations 1994, SI No3260 (Regulation 5 (1)) Electromagnetic Compatability Directive 89/336/EEC Low Voltage Directive 72/23/EEC (article 2) as amended by 93/68/EEC EN :1992 EN :1992 EN :1994 inc AMDS A11, A1, A12, A13, A14, A2, A15 and A16 - Safety Of Household and Similar Electrical Appliance EN : 1993 EN : A1: A2: 1998EN : 1995 EN : 1997 Category 2 EN : Particular Requirements for Service Machines and Amusement Machines RoHS SUPPLIER DECLARATION As of July 1st 2006 unless otherwise stated on order confirmations, all products manufactured by Northern Leisure Group Ltd are manufactured in accordance with RoHS directive 2002/95/EC Authorised Signatory: Manufacturer Name: Richard Pike Date Of Issue: June 2016 Position: Technical Manager Place Of Issue: Leeds, England

25 NORD COMPOSITES TECHNICAL DATA SHEET NORESTER 976 Fire retardant resin NTR 252 A - 12/11/12 Page : 1/2 1 CHARACTERISTICS The resin Norester 976 is a fire retardant resin fomulated from polyester orthophtalic resin It is thixotropic, filled, halogen free and antimony oxide free Application hand lay-up and spray-up Polymerise at room temperature with addtion of MEKP Good wetting out of reinforcements Low styrene emission in application Norester 976 is an opaque resin and gives laminates, which answer to this following classification: Class 2 according to the norm BS476 part 7 (Certificate N dated on 02/10/12) 2 PROPERTIES OF THE LIQUID RESIN Aspect Brookfield viscosity (ISO C sp3) Specific gravity (ICON 012) Gel time Not pre-accelerated version (NPA) (ICON 002) (20 C - 01% CO6%, 2% MEKP on 100 g) Gel time Pre-accelerated version (PA) (ICON 002) (20 C - 2% MEKP on 100 g) Non volatile content (ICON 003) White liquid 50 rpm : cps g/cm minutes minutes 65-69% 3 MECHANICAL PROPERTIES OF THE CURED RESIN ON LAMINATE Flexural strength * (ISO 178) Flexural modulus * (ISO 178) Tensile strength * (ISO 527) Module de traction * (ISO 527) 1872 MPa 8025 GPa 1137 MPa 2127 GPa Glass content 3388% Barcol hardness * 50 (ASTM 2583) * Mechanical tests realised on a laminate made with 4 layers 450 g/m², pre accelerated resin with 01% Co6% and catalyzed at 2% of MEKP Post cure: >24h at room temperature and 3 hours at 80 C Flexural strength * (ISO 178) Flexural modulus * (ISO 178) 4 MECHANICALS PROPERTIES OF CURED CAST RESIN 4954 MPa 4835 Gpa IMPORTANT All of the results obtained according to trials in our laboratory However, we don t be responsible of manufactured parts with the resin NORESTER 976, if the application conditions specified are not respected The user must also ensure that his application is appropriate for this product to be used We hereby the conformity of our products with the above specifiations We cannot be responsible for any damage caused by misuse of this product ZA route d Amiens Condé-Folie FRANCE Tél : Fax :

26 NORD COMPOSITES TECHNICAL DATA SHEET NORESTER 976 Fire retardant resin NTR 252 A - 12/11/12 Page : 2/2 Tensile strength * (ISO 527) 2706 MPa Tensile Modulus* (ISO 527) 3024 GPa Elongation at break * (ISO 527) 150% Temperature of deflection under load * (HDT) (ISO 75-3) 574 C Barcol hardness * (ASTM 2583) *mechanicals tests realized on cast resin pre accelerated with 01% Co6% and catalyzed at 2% of MEKP Post-cure : >24H at room temperature and 3H at 80 C 5 VERSIONS Available in white version reference Norester 976 PA White with a gel time of min (20 C - 2% MEKP on 100 g) 6 RECOMMENDATIONS BEFORE USE During storage, a settling low of the charge may appear Mix the product thoroughly before use so as to have a homogeneous mixture Before use, check that the temperature of the product, the mould and the room is between 18 C and 25 C For NPA version, t ake care not to mix the accelerator and the peroxide together but add them seperatly in the resin Mix the peroxide well, never put under 1% or over 2% We recommend to add 2% of MEKP peroxide in the resin We retain the attention on the fact that the Norester 976 is classified according to the certificates named above and tested on applications produced in our laboratory It is the responsibility of the customer to assure that the parts he produces are well classified 7 POST CURING To obtain optimum resistance properties, the laminate with the Norester 976 must be post-curing In order to accelerate the hardening, the laminate stays at ambient temperature (16 à 20 C) during 24 hours followed a postcuring of 16 hours at 40 C We advise to do a post-curing immediately after ripening period to obtain optimums results 8 PACKAGING Available in cans of 25 Kg and drums of 250 Kg 9 STORAGE CONDITIONS AND HANDLING Storage life: NORESTER 976 resin is stable for 3 months from date of production The product must be stored in original closed packaging at a temperature between 15 C and 25 C, away from direct sunlight It is the responsibility of the customer to assure that the product is used in good conditions overall before the date limitation mentioned on the keg This resin is subject to the Highly Flammable Liquids Regulations IMPORTANT All of the results obtained according to trials in our laboratory However, we don t be responsible of manufactured parts with the resin NORESTER 976, if the application conditions specified are not respected The user must also ensure that his application is appropriate for this product to be used We hereby the conformity of our products with the above specifiations We cannot be responsible for any damage caused by misuse of this product ZA route d Amiens Condé-Folie FRANCE Tél : Fax :