OWNERS MANUAL RV2400A/RV2600B

Transcription

1 SP6636 1/10/07 9:52 AM Page 1 OWNERS MANUAL RV2400A/RV2600B LARGE CAPACITY - 2-STAGE COMMERCIAL & HOUSEHOLD WET/DRY VACS For Your Safety: Read all instructions carefully before using. Save this manual for future reference FOR QUESTIONS OR INFORMATION CONTACT US AT RIDGID ( ) OR Part No. SP6636 Printed in Canada

2 SP6636 1/10/07 9:52 AM Page 2 Table of Contents Section Page Table of Contents Important Safety Instructions Safety Signal Words Grounding Instructions Introduction Unpacking and Checking Carton Contents Tools Required Carton Contents List Replacement Filter Assembly Drum/Caddy Assembly Installing Handle Removing Handle Installing Tool Holder Wet/Dry Vac Assembly Insert Hose and Accessory Assembly Operation Vacuuming Dry Materials Vacuuming Liquids IMPORTANT SAFETY INSTRUCTIONS Safety is a combination of common sense, staying alert, and knowing how your Wet/Dry Vac works. Read and understand this manual and all labels on the Vac before operating. Use only as described in this manual. Never operate unattended. Safety Signal Words DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. When using your Wet/Dry Vac ( Vac ), always follow basic safety precautions including the following: WARNING - To reduce the risk of fire, electric shock, or injury: Read and understand this owner's manual and all labels on the Wet/Dry Vac before operating. Use only as described in this manual. Section Page Filter Performance Sensor Emptying the Drum Moving the Wet/Dry Vac Blowing Feature Accessory and Hose Storage Cord Wrap Maintenance Filter Removal Dry Filter Wet Filter Installation Clean & Disinfecting the Wet/Dry Vac Storage Casters & Wheels Frame & Handles Filter Replacement Repair Parts Warranty To reduce the risk of personal injury or damage to Vac, use only Ridgid recommended accessories. Do not leave Vac running while unattended. Sparks inside the motor can ignite flammable vapors or dust. To reduce the risk of fire or explosion: - Do not vacuum or use near flammable or combustible liquids, gases, or explosive dusts, such as gasoline or other fuels, lighter fluid, cleaners, oil based paints, natural gas, hydrogen, coal dust, magnesium dust, aluminum dust, grain dust, or gun powder. - Do not use as a sprayer. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes. Do not vacuum fireplace soot or ash with standard filter. This is a very fine dust which may be exhausted back into the air. Use a fine dust filter instead. To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials. 2

3 SP6636 1/10/07 9:52 AM Page 3 Do not use or store near hazardous materials. To reduce the risk of electric shock, do not expose to rain or allow liquid to enter motor chamber inside lid. Store indoors. Do not allow Vac to be used as a toy. Close attention is necessary when used by or near children. Do not use this Vac with a torn filter or without the filter installed except when vacuuming liquids as described in the operation section of this manual. Dry debris ingested by the impeller may damage the motor or be exhausted back into the air. Do not leave Vac when plugged in. Unplug from outlet when not in use and before servicing. Turn off Vac before unplugging. To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Do not use with damaged cord, plug or other parts. If your Vac is not working as it should, has missing parts, has been dropped, damaged, left outdoors, or dropped into water, return it to an Authorized Service Center. Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. Do not run Vac over cord. Keep cord away from heated surfaces. Do not handle plug or the Vac switch with wet hands. Do not put any object into ventilation openings. Do not vacuum with any ventilation openings blocked; keep free of dust, lint, hair or anything that may reduce air flow. Connect to a properly grounded outlet only. See Grounding Instructions in this manual. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. To reduce the risk of falls, use extra care when cleaning on stairs. To reduce the risk of back injury or falls, do not lift a Vac that is heavy with liquid or debris. Partially empty the Vac by scooping debris or draining liquid from the drum to make it comfortable to lift. When using as a blower: - Direct air discharge only at work area. - Do not direct air at bystanders. - Keep children away when blowing. - Do not use blower for any job except blowing dirt and debris. - Do not use as a sprayer. - Wear safety eyewear. - Use extra care on uneven surfaces that let the Vac tip or rock. WARNING: To reduce the risk of eye injury, wear safety eyewear. The operation of any utility vac or blower can result in foreign objects being blown into the eyes, which can result in severe eye damage. Always wear safety eyewear complying with ANSI Z87.1 (or in Canada CSA Z94.3) before starting operation. Everyday eyeglasses are not safety glasses and could seriously hurt you when they break. CAUTION: To reduce the risk of hearing damage, wear ear protectors when using the Vac for extended hours or when using it in a noisy area. CAUTION: For dusty operations, wear dust mask. NOTE: Static shocks are common in dry areas or when the relative humidity of the air is low. Vacuuming fine debris with your vac can deposit static charge on the hose or on the Vac. The best remedy to reduce the frequency of static shocks in your home or when using this Vac is to add moisture to the air with a humidifier. 3

4 SP6636 1/10/07 9:52 AM Page 4 WARNING: Use only extension cords that are rated for outdoor use. Extension cords in poor condition or that are too small in wire size can pose fire and shock hazards. When using an extension cord, be sure it is in good condition. Using any extension cord will cause some loss of power. To keep the loss to a minimum, use the following table to choose the minimum wire size extension cord. Extension Cord Length Gauge A.W.G Ft Ft. 12 Grounding Instructions Observe the following warnings that appear on the motor housing of your Wet/Dry Vac. WARNING: To reduce the risk of electric shock - do not expose to rain - store indoors. WARNING: For your own safety, read and understand owner s manual. Do not run unattended. Do not pick up hot ashes, coals, toxic, flammable or other hazardous materials. Do not use around explosive liquids or vapors. SAVE THIS MANUAL FOR FUTURE REFERENCE This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING - Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Grounding Prong Properly Grounded Outlet 3-Prong Plug This vac is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug shown. A temporary adapter that looks like the adapter shown may be used to connect this plug to a 2-pole receptacle, as shown. If a properly grounded outlet is not available, the temporary adapter should only be used until a properly grounded outlet can be installed by a qualified electrician. 4

5 SP6636 1/10/07 9:52 AM Page 5 The green-colored rigid ear, lug, or the like, extending from the adapter, must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. NOTE: In Canada, the use of a temporary adaptor is not permitted by the Canadian Electrical Code. 2-Prong Outlet Green Grounding Lug 3-Prong Plug Adapter Make sure this is a metal screw connected to a known ground Introduction This Vac is rated for commercial and household use. This Wet/Dry Vac is supplied with a three-layer fine dust filter. It can be used not only to pick up material like sawdust and gravel but also ultra fine material like drywall dust and cold fireplace ash. These types of materials are so small they would pass through traditional filters. Unpacking and Checking Carton Contents Tools Required Phillips Screwdriver Hammer Mallet Refer to the assembly sketch for positioning of parts. Remove contents of carton. Check each item against the Carton Contents List. Call RIDGID ( ) or us at info@ridgid.com if any parts are damaged or missing. 5

6 SP6636 1/10/07 9:52 AM Page 6 Unpacking and Checking Carton Contents (cont.) Carton Contents List Key Description Qty A Wet/Dry Vac Assembly...1 B* Filter Nut...1 C* Fine Dust Filter...1 D* Filter Cage...1 E* Float...1 F Tug-A-Long Hose...1 G Muffler/Diffuser...1 H Owner s Manual...1 A B D C * These items may come preassembled. If they are not present in the carton check the vac power head to see if they are preassembled. E F G H Key Description Qty Carton containing the following parts: J Storage Bag...1 K 8 Wheel...2 L Metal Handle...1 M Axle...1 N* Caddy, Right...1 P* Caddy, Left...1 * These items may come preassembled. If they are not present in the carton check the Wet/Dry Vac assembly to see if they are preassembled. J P N L K M 6

7 SP6636 1/10/07 9:52 AM Page 7 Unpacking and Checking Carton Contents (cont.) Key Description Qty Bag of Loose Parts - Containing the following: R 2 Caster...2 S 1/2 Cap Nut...2 T Wheel Caps...2 U Screw, Type AB #10 x 1-3/4...4 S U T R 2-1/2 Accessories For Stock Number RV2400A Carton Contents List Key Description Qty A 14 Floor Brush...1 B Wet Nozzle...1 C Crevice Tool...1 D Utility Nozzle...1 E Extension Wands...2 A C D B E 1-7/8 Accessories For Stock Number RV2600B A Carton Contents List Key Description Qty A Multi-Nozzle Body...1 B Floor Brush Insert...1 C Squeegee Insert...1 D Carpet Insert...1 E Extension Wands...2 F Claw Nozzle...1 G Crevice Tool...1 H Dusting Brush...1 F B C D E G H 7

8 SP6636 1/10/07 9:52 AM Page 8 Replacement Filter Assembly 1. Carefully slide the filter over the filter cage, sliding it over the center ring covering the 3 slots until the filter stops against the lid. 2. Place filter nut onto threaded stud and tighten it down. Finger tighten only. NOTE: Lever of filter nut should be away from plate as shown. IMPORTANT: Do not overtighten as this may deform or crack the filter cage, or filter. Filter Nut Lever Lid Filter Nut Filter Plate Filter Threaded Stud Filter Cage Slots (3) Filter Cage Assembly NOTE: If filter cage needs to be removed, because the float is placed in the wrong way, use a flat blade screwdriver and insert the blade near one of the tabs between the filter cage and the center ring of the lid. Pry the tab out of the slot. Tilt the cage and lift away from the lid. To replace, follow the assembly instructions below: WARNING: For your own safety, never connect plug to power source outlet until all assembly steps are complete and you have read and understood the safety and operation instructions. Do not operate vac with any parts damaged or missing. 1. Place the float over the opening in the center of the lid with the words "This Side Towards Lid" laying face down over the hole. Filter Cage THIS SIDE TOWARD LID Tabs (3) Float Solid End Power Head Assembly Lid WARNING: To avoid personal injury or damage to vac, be sure to keep hands, fingers, or any other foreign objects out of the center opening when assembling the float. Filter Cage Tabs (3) Slots (3) Slots (3) 2. Line up filter cage tabs with slots in the center ring of the lid. 3. Push on the filter cage until the tabs snap into slots for a secure fit. 8

9 SP6636 1/10/07 9:52 AM Page 9 Drum/Caddy Assembly If any parts are missing or damaged contact Customer Service. Do not assemble until you have all the parts. NOTE: Smooth side of the wheel to the outside. Cap Nut 1. Remove left and right caddies from drum. 2. Install cap nut on one side of shaft rod. Tap gently with rubber mallet or hammer until fully seated. Slide open end of shaft through the wheel (smooth side of wheel facing outward). 3. Place wheel/shaft assembly through caddy left and on through the caddy right, as shown. 4. Then place the remaining wheel onto the caddy assembly (smooth side of wheel facing outward), and install second cap nut. 5. Invert drum to install caddy. Place the caddy assembly onto the drum, as shown. Be sure that wheels spin freely, and do not contact the caddies. 6. Once the caddies are aligned on the drum, gently tap each end of each caddy until firmly seated. It is recommended to tap the center portion of the front caddies, as shown. 7. Using a rubber mallet or hammer, gently tap the wheel caps onto each wheel until the wheel caps are firmly seated onto each wheel. This is required on both sides. Shaft Rod Caddy Right CADDY ASSEMBLY 1/16" Clearance TAP Caddy Left TAP Wheel Cap Nut Caddy Wheel Wheel Cap Mallet 9

10 SP6636 1/10/07 9:52 AM Page 10 Drum/Caddy Assembly (cont.) 8. Insert the caster stem into the socket of the caster foot as shown. (Front casters only). 9. Push on the caster until the ball on the caster stem is inserted all the way into the socket. You will be able to hear the ball snap into the socket and the caster will swivel easily when positioning is correct. 10. Install (4) #10 x 1-3/4 screws into matching holes on both right and left side of caddy, securing the caddies to the bottom of the drum. Tighten screws until just snug. Do not over tighten the screws, as this may deform the caddies. Caster (2) Socket Caster Stem Caster Ball #10 x 1-3/4" Screw (4) Installing Handle Press and hold release buttons while installing handle into handle receptacles in drum (See illustration). NOTE: An audible snap of release buttons indicates successful engagement of handle. Removing Handle Press and hold release buttons as shown. While firmly pushing in release buttons, pull handle upwards to remove (see illustration). 10

11 SP6636 1/10/07 9:52 AM Page 11 Installing Tool Holder 1. Install tool holder as shown with extension wand holders facing unit. Tote Snaps Tote Straps (4) Handle 2. As an alternative storage solution, the tool holder may hang on a wall. Two wall mounting hooks (not provided) must be secured to the wall as shown (sold separately). Grommet Extension Wand Storage Locations Wall Mount Hook Wall Wet/Dry Vac Assembly 1. Position the powerhead assembly on the drum/caddy assembly as shown (assembled earlier). 2. Rotate both latches down and press until you hear them snap over the flanges on the drum. Drum Latch Drum Latch Drum Flange Insert Hose Insert the push button end of the Tug-A- Long hose into the inlet of the vac. The hose should snap into place. To remove the hose from the vac, press the release button in the hose assembly and pull the hose out of the vac inlet, as shown. On the RV2600B, press the curved metal extension wand into the coupling ring of the hose end. Join the two metal extension wands, aligning the button and hole so they snap together. Attach the accessories, aligning the button and hole so they snap together. Coupling Ring Press and Pull Release Button Powerhead Assembly Latch Drum Metal Extension Wand (Curved) Metal Extension Wand (Straight) Accessory Wet/Dry Vac & Hose Assembly 11

12 SP6636 1/10/07 9:52 AM Page 12 Operation WARNING To reduce the risk of fire or explosion, do not operate this vac in areas with flammable gases, vapors or explosive dust in the air. Flammable gases or vapors include but are not limited to: lighter fluid, solvent type cleaners, oilbase paints, gasoline, alcohol or aerosol sprays. Explosive dusts include but are not limited to: coal, magnesium, aluminum, grain or gun powder. Do not vacuum explosive dust, flammable or combustible liquids or hot ashes. Do not use this vac as a sprayer. To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials. WARNING: The operation of any utility vac can result in foreign objects being blown into the eyes, which can result in severe eye damage. Always wear safety eyewear complying with ANSI Z87.1 (or in Canada, CSA Z94.3) before starting operation. Safety eyewear is available at many local retail stores. CAUTION: To reduce risk of hearing damage, wear ear protectors when using the vac for extended hours or when using it in a noisy area. After you plug the power cord into the outlet, turn the unit on by pushing the switch from position "O" to position "l". The symbols used on the switch actuator are international "On & Off" symbols. "O" is the symbol for "OFF" and "l" is the symbol for "ON". = OFF = ON Familiarize yourself with the accessories included with the vac. Each accessory may be used in various ways for vacuuming and blowing debris. Here is a list of possible accessories and their uses. 1-7/8 Multi-Nozzle Body - Holds floor inserts for specialized cleaning applications: Floor Brush, Squeegee, and Carpet Inserts. To change inserts, slide red tabs to the open position and pull insert from the center. Install new insert flush with nozzle body and slide tabs to the lock position. 1-7/8 Floor Brush Insert - Used for large area clean-ups on smooth surfaces. 1-7/8 Squeegee Insert - Used for wet pickup on smooth surfaces to pick up liquid and dry the surface in one stroke. 1-7/8 Carpet Insert - Dry and wet pickup nozzle for most upholstery and carpet cleaning. 1-7/8 Claw Nozzle - Use to pick up debris in hard to reach locations. 1-7/8 Dusting Brush - Used for detailed cleaning in small spaces. Crevice Tool - Use to pick up debris in hard to reach locations. Muffler/Diffuser - Use to disperse the exhaust air stream while reducing noise. Insert into the blowing port. Extension Wands - These wands can be connected together and provides additional length for more reach. Hose - Provides transfer of vacuum or blowing capability to work site. Provides the means of attaching extension wands and nozzles. 2-1/2 Utility Nozzle - General purpose nozzle for most vacuuming applications. 2-1/2 Wet Nozzle - Used for wet pickup on smooth surfaces to pick up liquid and dry the surface in one stroke. 2-1/2 Floor Brush - Used for large area clean-ups on smooth surfaces. 12

13 SP6636 1/10/07 9:52 AM Page 13 Vacuuming Dry Materials 1. The filter must always be in correct position to reduce the risk of leaks and possible damage to vac. 2. Your Wet/Dry Vac comes with the VF5000 Filter installed. When using your vac to pick up very fine dust, it will be necessary for you to empty the drum and clean the filter at more frequent intervals to maintain peak vac performance. NOTE: A dry filter is necessary to pick up dry material. If you use your vac to pick up dust when the filter is wet, the filter will clog quickly and be very difficult to clean. 3. If your filter is wet but you need to use the vac to pick up dry material, you can quickly dry the filter by running the vac without hose attached for about 10 minutes. The clean air rushing through the vac will help dry the filter. Vacuuming Liquids IMPORTANT: 1. When picking up small amounts of liquid the filter may be left in place. 2. When picking up large amounts of liquid the filter should be removed. With the filter removed, the float mechanism activates to prevent water from entering the motor blower housing. If the filter is not removed, water could enter the motor blower housing which could overload and damage the motor. IMPORTANT: If water mist appears in the exhaust, run unit 10 minutes to dryout acoustical foam inside air passageways. 3. After using the vac to pick up liquids, the filter must be dried to reduce the risk of possible mildew and damage to the filter. 4. When the liquid in the drum reaches a predetermined level, the float mechanism will rise automatically to cut off air-flow. When this happens, turn off the vac, unplug the power cord, and empty the drum. You will know that the float has risen because vac airflow ceases and the motor noise will become higher in pitch, due to increased motor speed. IMPORTANT: To reduce the risk of damage to the vac do not run motor with float in raised position. Emptying the Drum WARNING: To reduce the risk of injury from accidental starting, unplug power cord before emptying the drum. WARNING: To reduce the risk of back injury or falls, do not lift a vac heavy with liquid or debris. Scoop or drain enough contents out to make the vac light enough to lift comfortably. 1. The vac comes equipped with a drain for easy emptying of liquids. Simply unscrew the drain cap and lift the opposite side slightly to empty the drum. 2. Another option is to remove the powerhead assembly. 3. Lay powerhead assembly aside on a clean area while emptying drum. 4. Dump the drum contents into the proper waste disposal container. Moving the Wet/Dry Vac Should it become necessary to pick the vac up to move it, the handle on the sides of the dust drum are used to lift. To maneuver the vac, the push/pull handle in the rear of the unit should be used. 13

14 SP6636 1/10/07 9:52 AM Page 14 Operation (cont.) Blowing Feature Your vac features a blowing port. It can blow sawdust and other debris. Follow the steps below to use your vac as a blower. WARNING: Always wear safety eyewear complying with ANSI Z87.1 (or in Canada, CSA Z94.3) before using as a blower. WARNING: To reduce the risk of injury to bystanders, keep them clear of blowing debris. 1. Locate blowing port of your vac. 2. Insert the locking end of the tug-along hose into the blowing port of the vac. The hose should snap into place. To remove the hose from the vac, press the release button in the hose assembly and pull the hose out of the vac inlet. 3. (Optional) Attach extension wand to opposite end of hose. 4. Turn vac on and you are ready to use your vac as a blower. WEAR YOUR FORESIGHT IS BETTER THAN NO SIGHT Blowing Port Tug-A-Long Hose 14

15 SP6636 1/10/07 9:52 AM Page 15 Accessory and Storage Your accessories may be stored in the removable tote, or in the two locations on the caddy right/left. The hose may be stored by wrapping it around the unit and placing each end into the two areas marked Hose Storage. NOTE: Insert male end of extension wand into the holder sleeve as shown. The hose may be stored by wrapping it around the unit and plugging the open end into one of the storage locations on the caddy assembly. HOSE STORAGE HOSE STORAGE Maintenance Filter Hose Storage Area WARNING: To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter. RV2400A/RV2600B Wet/Dry Vacs are supplied with RIDGID s Three Layer Fine Dust Filter. Replacement Three Layer Fine Dust Filters are available where you purchased your vac. Ask for the RIDGID Three Layer Fine Dust Filter VF5000. NOTE: The filter is made of high quality paper designed to stop very small particles of dust. The filter can be used for wet or dry pick up. Handle the filter carefully when removing to clean or installing it. Creases in the filter pleats may occur from installation but not affect the performance of the filter. Accessory Storage Compartment Extension Wand Extension Wand Storage Cord Wrap When vacuuming is complete, unplug the cord and wrap it around the power assembly as shown. The cord should wrap under the pull handle (above the inlet) and around and under the cord wrap of the motor cover. Push/Pull Handle Cord Wrap Power Cord WARNING: Do not operate the Wet/Dry Vac with the filter cage and float removed. The float prevents water from entering the impeller and damaging the motor. The cage prevents fingers from touching the moving impeller. Removal To remove the filter for cleaning or replacement, unscrew the filter nut from the filter cage, remove filter plate and lift off filter. IMPORTANT: To avoid damage to the blower wheel and motor, always reinstall the filter before using the vac for dry material pick-up. Dry Filter NOTE: For best cleaning results due to accumulated dust, clean the filter in an open area. Cleaning SHOULD be done outdoors and not in the living quarters. 15

16 SP6636 1/10/07 9:52 AM Page 16 Maintenance (cont.) 1. Remove filter from vac. Gently tap filter against the inside wall of your dust drum. The debris will loosen and fall. 2. For thorough cleaning of dry filter with fine dust (no debris), run water through it as described under "Wet Filter". Wet Filter After filter is removed, run water through the filter from a hose or spigot. Take care that water pressure from the hose is not strong enough to damage filter. Remember: To dry a filter quickly, reinstall the filter on the vac and allow the unit to run for approximately 10 minutes. The clean air rushing through the filter will dry it. IMPORTANT: After cleaning, check the filter for tears or small holes. Do not use a filter with holes or tears in it. Even a small hole can cause a lot of dust to come out of your vac. IMPORTANT: If Damaged, Replace Filter Immediately. Installation Refer to "Replacement Filter Assembly" Section of this manual. Allow the filter to dry before reinstalling and storing the vac. Cleaning and Disinfecting the Wet/Dry Vac To keep your Wet/Dry Vac looking its best, clean the outside with a cloth dampened with warm water and mild soap. To clean the drum: 1. Dump debris out. 2. Wash drum thoroughly with warm water and mild soap. 3. Wipe out with dry cloth. Before prolonged storage or as needed (i.e., waste water pick up) the drum should be disinfected. To disinfect the drum: 1. Pour 1 gallon of water and 1 teaspoon chlorine bleach into the drum. 2. Let solution stand for 20 minutes, carefully swishing every few minutes, making sure to wet all inside surfaces of the drum. 3. Empty drum after 20 minutes. Rinse with water until bleach smell is gone. Allow drum to dry completely before sealing the motor on the drum. Storage Before storing your vac, the drum should be emptied and cleaned. The cord should be wrapped around the unit and the hose should be stored as described in this manual. Accessories should be kept in the same area as the vac so they can be readily available. The vac should be stored indoors. Casters and Wheels Should your cart squeak or become hard to roll, you should place two or three drops of general purpose oil on each wheel at the axle. If your casters are noisy, you may put a drop of oil on the roller shaft to make them quieter. Frame and Handles Your metal handle is painted to prevent rust, however, liquids and corrosive debris should be wiped off with a soft cloth should they come in contact with the handle. WARNING: To assure product SAFETY and RELIABILITY, repairs and adjustments should be performed by Authorized Service Centers, always using RIDGID replacement parts. 16

17 SP6636 1/10/07 9:52 AM Page 17 Filter Replacement Which RIDGID Filter is Best Suited for Your Particular Cleaning Application: Sawdust Wood Chips Jobsite Debris Car/Truck Dirt Drywall Dust Concrete Dust Cold* Fireplace/ Grill Ashes Pollen Allergens Pleated Filters: Standard Pleated Filter Day-to-Day Dirt 4000 VF4000 Fine Dust Filter Microban antimicrobial product protection * VF3500/VF5000 *Use VF3500 (short filter) for Wet/Dry Vacs smaller than five-gallons. VF6000 Allergen Filter Microban antimicrobial product protection High Efficiency Filter Bags: VF3501 VF3502 Filter Bag Fits RIDGID 4 Gallon Portable Vacs Disposable Filter Bag Fits RIDGID Gallon 1 or 2-Stage Vacs Disposable 17

18 SP6636 1/10/07 9:52 AM Page 18 Repair Parts 14 & 16 Gallon Wet/Dry Vac Stock Numbers RV2400A or RV2600B RIDGID parts are available on-line at Always order by Part Number - Not by Key Number Key RV2400A RV2600B No. Part No. Part No. Description Actuator, Switch Switch, Toggle Motor Brush Motor Assembly Cord Assembly 6 VT2525 VT2525 Muffler/Diffuser Drum Latch A A Float Filter Cage 10 VF5000 VF5000 Filter - 3-Layer Filter Nut Motor Gaskets (2) 13 VT1785 Dusting Brush Multi-Nozzle Body Floor Brush Insert Replacement Floor Brush Inserts (set of long & short brushes) Carpet Insert Squeegee Insert Replacement Squeegee Inserts (set of long & short rubber squeegees) Claw Nozzle Tug-A-Long Hose Extension Wand Upper (metal) Extension Wand Lower (metal) 24 VT2514 Floor Brush 25 VT2510 Wet Nozzle 26 VT2502 VT1786 Crevice Tool 27 VT2509 Utility Nozzle 28 VT2508 Extension Wands 29 SP6636 SP6636 Owner s Manual 18

19 SP6636 1/10/07 9:52 AM Page 19 RIDGID parts are available on-line at

20 SP6636 1/10/07 9:52 AM Page 20 Repair Parts 14 & 16 Gallon Wet/Dry Vac Stock Numbers RV2400A or RV2600B RIDGID parts are available on-line at Always order by Part Number - Not by Key Number Key RV2400A RV2600B No. Part No. Part No. Description Handle Dust Drum Assembly Drain Cap Wheel Cap Cap Nut 1/ Wheel Assembly (Includes Key No. 4 and 5) Shaft Caddy, Right Caddy, Left Caster Tote Screw Type AB #10 x 1-3/ Bag of Loose Parts (Not Illustrated) (Includes Key No. 4, 5, 10 and 12) 20

21 SP6636 1/10/07 9:52 AM Page 21 RIDGID parts are available on-line at

22 SP6636 1/10/07 9:52 AM Page 22 What is covered RIDGID tools are warranted to be free of defects in workmanship and material. How long coverage lasts This warranty lasts for the lifetime of the RIDGID tool. Warranty coverage ends when the product becomes unusable for reasons other than defects in workmanship or material. How can you get service To obtain the benefit of this warranty, deliver via prepaid transportation the complete product to RIDGE TOOL COMPANY, Elyria, Ohio, or any authorized RIDGID INDEPENDENT SERVICE CENTER. Pipe wrenches and other hand tools should be returned to the place of purchase. What we will do to correct problems Warranted products will be repaired or replaced, at RIDGE TOOL S option, and returned at no charge; or, if after three attempts to repair or replace during the warranty period the product is still defective, you can elect to receive a full refund of your purchase price. What is not covered Failures due to misuse, abuse or normal wear and tear are not covered by this warranty. RIDGE TOOL shall not be responsible for any incidental or consequential damages. How local law relates to the warranty Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific rights, and you may also have other rights, which vary, from state to state, province to province, or country to country. No other express warranty applies This FULL LIFETIME WARRANTY is the sole and exclusive warranty for RIDGID products. No employee, agent, dealer, or other person is authorized to alter this warranty or make any other warranty on behalf of the RIDGE TOOL COMPANY. Stock No. RV2400A or RV2600B Model No. RV24000 or RV26000 Model and serial number may be found on the handle. You should record both model and serial numbers in a safe place for future use. QUESTIONS OR COMMENTS? CALL RIDGID ( ) Please have your Model Number and Serial Number on hand when calling. c 2007 Emerson Professional Tools Emerson Tool Company A Division Of Emerson Electric Co. Part No. SP6636 Form No. SP6636 Printed in Canada 01/07

23 SP6636 1/10/07 9:52 AM Page 23 MANUAL DEL USUARIO Para su seguridad: Lea detenidamente todas las instrucciones antes de usar. Guarde este manual para referencia futura. SI TIENE PREGUNTAS O DESEA INFORMACIÓN, CONTÁCTENOS LLAMANDO AL RIDGID ( ) O No. de pieza SP6636 RV2400A/RV2600B ASPIRADORAS PARA MOJADO/SECO DE 2 ETAPAS DE GRAN CAPACIDAD PARA USO COMERCIAL Y DOMÉSTICO Impreso en Canada

24 SP6636 1/10/07 9:52 AM Page 24 Indice Sección Página Indice Instrucciones de seguridad importantes Palabras de señal de seguridad Instrucciones de conexión a tierra Introducción Desempaquetado y comprobación del contenido de la caja de cartón Herramientas necesarias Lista del contenido de la caja de cartón Ensamblaje de un filtro de reemplazo Ensamblaje del tambor/base de soporte Instalación del asa Remoción del asa Instalación del portaherramientas Ensamblaje de la aspiradora para mojado/seco.. 33 Introduzca la manguera Funcionamiento Recogida de materiales secos con la aspiradora Recogida de líquidos con la aspiradora INSTRUCCIONES DE SEGURIDAD IMPORTANTES La seguridad es una combinación de sentido común, permanecer alerta y saber cómo funciona la aspiradora para mojado/seco. Lea y entienda este manual y todas las etiquetas colocadas en la aspiradora antes de utilizarla. Utilícela solamente de la manera que se describe en este manual. No la deje desatendida nunca mientras esté en marcha. Palabras de señal de seguridad PELIGRO: indica una situación inminentemente peligrosa que, si no se evita, causará la muerte o lesiones graves. ADVERTENCIA: indica una situación potencialmente peligrosa que, si no se evita, podría causar la muerte o lesiones graves. PRECAUCIÓN: indica una situación potencialmente peligrosa que, si no se evita, pudiera causar lesiones leves o moderadas. Cuando utilice la aspiradora para mojado/seco ( la aspiradora ), siga siempre las precauciones básicas de seguridad, incluyendo las siguientes. ADVERTENCIA Para reducir el riesgo de incendio, sacudidas eléctricas o lesiones: Lea y entienda este manual del usuario y todas las etiquetas que están colocadas en la aspiradora para mojado/seco antes de utilizarla Utilice la aspiradora únicamente de la manera que se describe en este manual. 24 Section Page Vaciado del tambor Traslado de la aspiradora para mojado/seco.. 35 Dispositivo de soplado Accesorios y almacenamiento Enrollado del cordón Mantenimiento Filtro Remoción del filtro Limpieza de un filtro seco Limpieza de un filtro mojado Instalación Limpieza y desinfección de la aspiradora para mojado/seco Almacenamiento Ruedecillas y ruedas Armazón y mangos Reemplazo del filtro Piezas de repuesto Garantía Para reducir el riesgo de lesiones corporales o daños a la aspiradora, utilice únicamente accesorios recomendados por Ridgid. No deje la aspiradora en marcha mientras esté desatendida. Las chispas que se producen en el interior del motor pueden incendiar los vapores inflamables o el polvo. Para reducir el riesgo de incendio o explosión: - No recoja con la aspiradora líquidos o gases inflamables o combustibles, o polvos explosivos como gasolina u otros combustibles, líquido encendedor, limpiadores, pinturas a base de aceite, gas natural, hidrógeno, polvo de carbón, polvo de magnesio, polvo de aluminio, polvo de granos de cereal o pólvora, ni use la aspiradora cerca de estos materiales. - No utilice la aspiradora como rociador. No recoja con la aspiradora nada que esté ardiendo o humeando, como cigarrillos, fósforos o cenizas calientes. No recoja con la aspiradora hollín ni cenizas de chimenea, ya que se trata de un polvo muy fino que no puede ser atrapado por el filtro estándar y puede ser expulsado de vuelta al aire. En lugar del filtro estándar, use un filtro para polvo fino. Para reducir el riesgo de que se produzcan peligros para la salud causados por vapores o polvo, no recoja con la aspiradora materiales tóxicos.

25 SP6636 1/10/07 9:52 AM Page 25 No use ni almacene la aspiradora cerca de materiales peligrosos. Para reducir el riesgo de descargas eléctricas, no exponga la aspiradora a la lluvia ni deje que entre líquido en la cámara del motor dentro de la tapa. Guarde la aspiradora en un lugar interior. No permita que la aspiradora se utilice como un juguete. Se necesita prestar máxima atención cuando sea utilizada por niños o cerca de éstos. No use esta aspiradora con un filtro desgarrado o si no tiene el filtro instalado, excepto cuando recoja líquidos de la manera que se describe en la sección Funcionamiento de este manual. Los residuos secos absorbidos por el impulsor podrían dañar el motor o ser expulsados de vuelta al aire. No abandone la aspiradora cuando esté enchufada. Desenchúfela del tomacorriente cuando no la esté utilizando y antes de realizar servicio de revisión. Apague la aspiradora antes de desenchufarla. Para reducir el riesgo de lesiones debidas a un arranque accidental, desenchufe el cordón de energía antes de cambiar o limpiar el filtro. No desenchufe la aspiradora tirando del cordón. Para desenchufarla, agarre el enchufe y no el cordón. No use la aspiradora con el cordón dañado, el enchufe dañado u otras piezas dañadas. Si la aspiradora no funciona como debe, le faltan piezas, se ha caído, ha sido dañada, se ha dejado a la intemperie o se ha caído al agua, devuélvala a un Centro de Servicio autorizado. No tire de la aspiradora usando el cordón ni la lleve por el cordón, ni use el cordón como asa, ni cierre una puerta sobre el cordón, ni tire del cordón alrededor de bordes o esquinas afilados. No pase la aspiradora en marcha sobre el cordón. Mantenga el cordón alejado de las superficies calientes. No maneje el enchufe o la aspiradora con las manos mojadas. No ponga ningún objeto en las aberturas de ventilación. No recoja nada con la aspiradora cuando cualquiera de las aberturas de ventilación esté bloqueada; mantenga dichas aberturas libres de polvo, pelusa, pelo o cualquier cosa que pueda reducir el flujo de aire. Conecte la aspiradora solamente a un tomacorriente conectado a tierra adecuadamente. Consulte las instrucciones de conexión a tierra. Mantenga el pelo, la ropa holgada, los dedos y todas las partes del cuerpo alejados de las aberturas y de las piezas móviles. Para reducir el riesgo de caídas, tenga cuidado adicional al limpiar en escaleras. Para reducir el riesgo de lesiones de espalda o caídas, no levante una aspiradora que pese mucho debido a que contiene líquido o residuos. Saque parte del contenido de la aspiradora o drénela parcialmente para hacer que sea lo suficientemente liviana como para poder levantarla cómodamente. Cuando utilice la aspiradora como soplador : - Dirija la descarga de aire solamente hacia el área de trabajo. - No dirija el aire hacia las personas que estén presentes. - Mantenga alejados a los niños durante la operación de soplado. - No utilice el soplador para trabajos que no sean soplar suciedad y residuos. - No use la aspiradora como rociador. - Use protección ocular de seguridad. - Tenga cuidado adicional en las superficies desiguales que pueden dejar que la aspiradora se incline u oscile. PRECAUCIÓN: Para reducir el riesgo de lesiones en los ojos, use protección ocular de seguridad. La utilización de cualquier aspiradora utilitaria o soplador utilitario puede hacer que se soplen objetos extraños hacia los ojos, lo cual puede causar daños graves en los ojos. Use siempre anteojos de seguridad que cumplan con la norma ANSI Z87.1 (o en Canadá, con la norma CSA Z94.3) antes de comenzar la operación. Las gafas corrientes no son anteojos de seguridad y podrían causarle lesiones graves al romperse. PRECAUCIÓN: Para reducir el riesgo de daños a la audición, use protectores de oídos cuando utilice la aspiradora durante muchas horas seguidas o cuando la emplee en un área ruidosa. PRECAUCIÓN: Para operaciones que generan polvo, use una máscara antipolvo. NOTA: Las descargas de estática son comunes en áreas secas o cuando la humedad relativa del aire es baja. Si recoge residuos finos con la aspiradora, se puede depositar carga estática en la manguera o en la aspiradora. El mejor remedio para reducir la frecuencia de las descargas de estática en su casa o cuando use esta aspiradora es añadir humedad al aire con un humidificador. 25

26 SP6636 1/10/07 9:52 AM Page 26 ADVERTENCIA: Utilice únicamente cordones de extensión que tengan capacidad nominal para uso a la intemperie. Los cordones de extensión que estén en malas condiciones o cuyo tamaño de alambre sea demasiado pequeño pueden conllevar peligros de incendio y sacudidas eléctricas. Cuando utilice un cordón de extensión, asegúrese de que esté en buenas condiciones. La utilización de cualquier cordón de extensión causará algo de pérdida de potencia. Para mantener la pérdida al mínimo, utilice la tabla que aparece a continuación para seleccionar el cordón de extensión con el tamaño de cable mínimo. Longitud del cordón Calibre del cable de extensión (A.W.G.) 0-50 pies pies 12 Siga las siguientes advertencias que aparecen en la caja del motor de la aspiradora para mojado/seco. ADVERTENCIA: Para reducir el riesgo de sacudidas eléctricas, no exponga la aspiradora a la lluvia y almacénela en interiores. ADVERTENCIA: Para su propia seguridad, lea y entienda el manual del usuario. No tenga en marcha la aspiradora desatendida. No recoja cenizas calientes, carbón caliente, materiales tóxicos ni inflamables ni otros materiales peligrosos. No use la aspiradora alrededor de líquidos o vapores explosivos. GUARDE ESTE MANUAL PARA REFERENCIA FUTURA Instrucciones de conexión a tierra Este electrodoméstico se debe conectar a tierra. En caso de mal funcionamiento o avería, la conexión a tierra proporciona una ruta de resistencia mínima para la corriente eléctrica con el fin de reducir el riesgo de sacudidas eléctricas. Este electrodoméstico está equipado con un cordón que tiene un conductor de conexión a tierra del equipo y un enchufe de conexión a tierra. El enchufe debe introducirse en un tomacorriente apropiado que esté instalado correctamente y conectado a tierra adecuadamente, de acuerdo con todos los códigos y ordenanzas locales. Terminal de conexión Grounding a tierra Prong Tomacorriente Properly conectado Grounded a tierra apropiadamente Outlet Enchufe de 33-Prong terminalesplug ADVERTENCIA: La conexión incorrecta del conductor de conexión a tierra del equipo puede causar un riesgo de sacudidas eléctricas. Consulte a un electricista calificado o a una persona de servicio competente si tiene dudas sobre si el tomacorriente está conectado a tierra apropiadamente. No modifique el enchufe suministrado con el electrodoméstico. Si el enchufe no cabe en el tomacorriente, haga que un electricista calificado instale un tomacorriente apropiado. Este electrodoméstico está diseñado para utilizarse en un circuito de 120 V nominales y tiene un enchufe conectado a tierra que tiene un aspecto como el del enchufe que se muestra en la ilustración. Se puede utilizar un adaptador temporal, que tenga un aspecto como el del adaptador que se muestra en la ilustración, para conectar este enchufe a un receptáculo de dos polos, de la manera que se muestra en la ilustración, si no se dispone de un tomacorriente conectado a tierra apropiadamente. El adaptador temporal debe utilizarse únicamente hasta que un electricista calificado pueda instalar un tomacorriente conectado a tierra apropiadamente. 26

27 SP6636 1/10/07 9:52 AM Page 27 La orejeta, lengüeta o pieza similar rígida de color verde que sobresale del adaptador se debe conectar a una toma de tierra permanente, como por ejemplo una tapa de caja tomacorriente conectada a tierra apropiadamente. Siempre que se utilice el adaptador, se debe sujetar en la posición correcta con un tornillo metálico. NOTA: En Canadá, el uso de un adaptador temporal no está permitido por el Código Eléctrico Canadiense. Tomacorriente para 2-Prong 2 terminales Outlet Green Orejeta verde de Grounding conexión a tierra Lug Enchufe de 3-Prong 3 terminales Plug Adapter Adaptador Asegúrese de que esto sea Make un tornillo sure this metálico is a metal conectado a screw una toma connected de tierra to conocida a known ground Introducción Esta aspiradora para mojado/seco tiene capacidad para uso comercial y doméstico. Esta aspiradora para mojado/seco se suministra con un filtro de tres capas para polvo fino. La aspiradora se puede utilizar no sólo para recoger material como aserrín y grava, sino también material ultrafino como polvo de panel de yeso y cenizas de chimenea frías. Estos tipos de materiales son tan pequeños que pasarían a través de los filtros tradicionales. Desempaquetado y comprobación del contenido de la caja de cartón Herramientas necesarias Destornillador Phillips largo Martillo Mazo Consulte el dibujo de ensamblaje para averiguar el posicionamiento de las piezas. Saque todo el contenido de la caja de cartón. Asegúrese de que no falte ningún artículo utilizando la lista del contenido de la caja. Llame al RIDGID ( ) o comuníquese con nosotros por correo electrónico a info@ridgid.com si alguna pieza está dañada o falta. 27

28 SP6636 1/10/07 9:52 AM Page 28 Desempaquetado y comprobación del contenido de la caja de cartón (cont.) Lista del contenido de la caja de cartón Clave Descripción Cant. A Ensamblaje de la aspiradora para mojado/seco...1 B* Tuerca del filtro...1 C* Filtro para polvo fino...1 D* Jaula del filtro...1 E* Flotador...1 F Maguera arrastrable...1 G Silenciador/Difusor...1 H Manual del usuario...1 A B D C * Estos artículos pueden venir preensamblados. Si no están presentes en la caja de cartón, compruebe el cabezal del motor de la aspiradora para ver si están preensamblados. E F G H Clave Descripción Cant. Caja de cartón que contiene las piezas siguientes: J Bolsa de almacenamiento...1 K Rueda de 8 pulgadas...2 L Mango metálico...1 M Eje...1 N* Base de soporte derecha...1 P* Base de soporte izquierda...1 * Estos artículos pueden venir preensamblados. Si no están presentes en la caja de cartón, compruebe el ensamblaje de la aspiradora para mojado/seco con el fin de verificar si están preensamblados. J P N L M K 28

29 SP6636 1/10/07 9:52 AM Page 29 Desempaquetado y comprobación del contenido de la caja de cartón (cont.) Clave Descripción Cant. Bolsa de piezas sueltas que contiene lo siguiente: R Ruedecilla de 2 pulgadas...2 S Tuerca de tapa de 1/2 pulgada...2 T Tapas de rueda...2 U Tornillo de tipo AB No. 10 x 1-3/4...4 S U T R Accesorios de 2-1/2" para el número de existencias RV2400A Lista del contenido de la caja de cartón Clave Descripción Cant. A Cepillo para pisos de 14 pulg...1 B Boquilla para mojado...1 C Boquilla rinconera...1 D Boquilla de uso general...1 E Tubos de extensión...2 A C D B E Accesorios de 1-7/8" para el número de existencias RV2600B Lista del contenido de la caja de cartón Clave Descripción Cant. A Cuerpo multiboquilla...1 B Inserto de cepillo para pisos...1 C Inserto de barredora de goma...1 D Inserto para alfombra...1 E Tubos de extensión...2 F Boquilla angulada...1 G Boquilla rinconera...1 H Cepillo para polvo...1 F A B C D E G H 29

30 SP6636 1/10/07 9:52 AM Page 30 Ensamblaje de un filtro de reemplazo 1. Deslice cuidadosamente el filtro sobre la jaula del filtro, deslizándolo sobre el anillo central que cubre las 3 ranuras hasta que el filtro se detenga contra la tapa. 2. Coloque la tuerca del filtro en el espárrago roscado y apriétela hacia abajo. Apriétela solamente con los dedos. NOTA: La palanca de la tuerca del filtro debe estar alejada de la placa, de la manera que se muestra en la ilustración. IMPORTANTE: No apriete excesivamente la tuerca, ya que esto puede deformar o agrietar la jaula del filtro o el filtro. Ensamblaje de la jaula del filtro NOTA: En caso de que sea necesario quitar la jaula del filtro debido a que el flotador esté colocado de manera incorrecta, utilice un destornillador de hoja plana e introduzca la hoja cerca de una de las lengüetas entre la jaula del filtro y el anillo central de la tapa. Haga palanca hacia afuera en la lengüeta hasta sacarla de la ranura. Incline la jaula y levántela para separarla de la tapa. Para colocar de nuevo la jaula, siga las instrucciones de ensamblaje que aparecen más adelante. ADVERTENCIA: Para su propia seguridad, nunca conecte el enchufe al tomacorriente de la fuente de energía hasta que haya completado todos los pasos de ensamblaje y haya leído y entendido las instrucciones de seguridad y utilización. No utilice la aspiradora si alguna de sus piezas está dañada o falta. Palanca de Filter la tuerca Nut Lever del filtro Tapa Lid Filter Jaula del Cage filtro Lengüetas Tabs (3) (3) Flotador Float Extremo Solid macizo End THIS SIDE TOWARD LID Tuerca Filter del Nut filtro Placa Filter del Plate filtro Filtro Filter Espárrago Threaded roscado Stud Filter Jaula del Cage filtro Slots Ranuras (3) (3) Power Ensamblaje Head del Assembly cabezal del motor Tapa Lid 1. Coloque el flotador sobre la abertura ubicada en el centro de la tapa con las palabras This Side Towards Lid (Este lado hacia la tapa) orientadas hacia abajo sobre el agujero (vea la ilustración). ADVERTENCIA: Para evitar lesiones personales o daños a la aspiradora, asegúrese de mantener las manos, los dedos o cualquier otro objeto extraño fuera de la abertura central cuando ensamble el flotador. 2. Alinee las lengüetas de la jaula del filtro con las ranuras del anillo central de la tapa. 3. Empuje sobre la jaula del filtro hasta que las lengüetas se acoplen a presión en las ranuras para lograr un encaje seguro. Filter Jaula del Cage filtro Lengüetas (3) Tabs (3) Ranuras (3) Slots (3) Ranuras Slots (3) (3) 30