Here in the UK there are two readily available gas types that will do the job. Both are available in the smallish 1 4 kg size (2.2 8.
|
|
- Dinah Lloyd
- 5 years ago
- Views:
Transcription
1 And now we come to the heating arrangement for your model traction engine First off, let s take a look at the gas fuel we can use... Here in the UK there are two readily available gas types that will do the job. Both are available in the smallish 1 4 kg size ( lbs) Propane Butane Both are readily available in gas bottles of varying dimensions that may suit a trailer, although the propane bottles tend to have a large handle sat on top for carrying purposes which takes up far too much of the trailer height and would make the trailer look totally disproportionate to PYRTE. Propane, being at a higher pressure in the bottle needs a regulator to reduce the pressure for burning purposes, again usually sat on top of the bottle more often than not sat within the confines of the handle for safety s sake, and produces a far fiercer flame at the burner end and for that reason generates more heat than Butane... Wait for it... There s a BUT... It also uses up the gas far quicker than Butane and is harder to light as it needs a flame for combustion to take place. Butane on the other hand has a flatter profiled bottle which suits the trailer size better and does not need such a great reduction in pressure = a smaller regulator = less height involved and merely needs a spark for ignition to take place. For the same amount of gas being used, apparently Butane is supposed to burn hotter than Propane. Now here s the BUT... And believe me, it s a GREAT BIG BUT! Here in the UK, and all over Europe too (I ve not explored the US yet, so I m afraid that will be up to someone else to tell you on that score), our Butane bottles have regulators with a pressure level set to suit camping gas stoves, barbeques and the likes, and this barely gives enough pressure to light PYRTE s burners, especially when it is trying to supply four, so that is pointless. It can be seen that with the awkward size of the Propane bottles and the reduced pressure with the Butane regulators, a compromise is needed. On the practical side, for economies sake, larger bottles would be used; but for our convenience we need to turn to the disposable gas cartridges that are readily available. They contain, generally speaking, 70% Butane (for ease of lighting) and 30% Propane. These give off a slightly higher pressure of gas and burns far more fiercely than neat Butane without the need for a large regulator.
2 There are generally three sizes of canister to choose from, but as we are to be using four burners, then the largest, around 450/500 gm (almost 1 lb) is the most suitable for our purposes. Do be careful though... These canisters tend to have a variety if fittings for the top for the gas outlet some with internal screw threads, others with external, some are a push-on fittings, and all with a confusing array of different thread sizes just to make it more awkward. And the worst part of it is, when you go to a supermarket or wherever for you gas purchase, the threads are protected by a plastic stopper so you can t see what you need to see to get the right match for your own fittings unless you actually buy the can. What I suggest you do is first of all get hold of your gas can valve from (one of our most highly recommended suppliers especially for the heating side of things any problems, Gerry s the man to ask) so you have something to start with. The thread on the gas bottles is a very odd-ball one, and making your own fittings for the bottle connections is really a non-starter + you need to consider the safety aspect of this also. It s just a matter of taking the fitting with you and asking for help in your local shop to find the matching gas bottles. You can go down the single gas can valve route if you wish, but the single narrow pipe connected to this valve limits the amount of gas flow to your burners, which tends to give a weaker flame. I tried one for a time when running four burners until I realised the rear two burners were well fed with gas, but the front two only half did what they were supposed to. It appears one can and its regulator is fine for 3 burners with number 5 gas jets, but not 4 burners. The simple answer was to be running on two bottles of gas with two gas can valves feeding into one pipe connection which fed the burners. Fine, light her up on one gas bottle, then add the other to get the steam pressure up before regulating the gas flow by reducing the gas from one bottle or both. Et voila... Perfect flames all the time. Sorry... I m telling porky s here. The two gases in these containers tend to be released at different stages, unless they are being shaken (mixed like when you are trundling along under steam). The Butane comes off first with easy combustion and a hot flame, and when you are down to the last 30+% you get the propane being introduced and the flame becomes less heated, less productive, often referred to as a lazy flame. With the four burners in place and two cans in use this is not a problem, but when I tried PYRTE with three burners and a single can, she had just enough heat produced to get up steam when the can was almost empty, but it seemed to take forever, and when a load was added (like pulling me around) she failed miserably.
3 So if you are going to be using PYRTE for a good steaming session, I recommend having two cans on the go, with a further two in your trailer for replacement purposes. Right... Next we come to the burners... In my early trials I was struggling to get enough heat under PYRTE s belly to get her to move at all. Recently, however, in the last few years, there has been an explosion (perhaps the wrong word in this case) of interest and demand for ceramic burners and I must admit I tried first one, then two together under PYRTE s belly, being ¾ x 5½ inches long. One barely did anything, not even managing to lift the needle from zero on the gauge any heat being passed into the boiler and water was simply radiating away as fast as it was introduced. What was needed was more heat, so a second burner was bought and installed. Please note: The supplier I used for the second burner you should avoid at all costs. I am speaking from personal experience here. The ceramic burner was ordered from Forest Classics whose web site I shall not show, and the burner took two months to arrive, despite regular contact with them. Car salesman springs to mind here - all flannel and promise, flashy site but very poor service. In the end I had to threaten court action to get the burner delivered. They are most certainly NOT recommended by me. With this extra burner the pressure reached up to 25 lbs/sq inch, just about... It may have got up to 30 the odd time when there was no wind, but as soon as the engine was run under steam, sat on my bench at the time, so under no load, the pressure dropped off and was not replaced, so PYRTE soon stopped turning over. I was getting more and more frustrated with this, until I saw one of Gerry s ads on Ebay (He was using Ebay as his main selling point, this was before he had set up a web site) and I thought I d try two of his burners to see how it went. They are obviously designed to fit Cheddar Models boilers as that s where he started off his steam career, and as Cheddars have gone belly-up, he decided to continue making parts for fellow Cheddar enthusiasts, along with others now. To be honest, I was a bit sceptical about this pair of burners, but when they arrived, my eyes were opened. After all the hype about ceramic burners being so wonderful and being sizzled into my brain over the last few years, and the advertisers jumping on the bandwagon and raising the prices no end, it was refreshing to find a burner that was better than the ceramic ones, around half the price and also less than half the space was needed. Gerry makes these burners himself, and also supplies many other fittings associated with burners and boilers, so you are assured of a good product.
4 I initially tried fitting one alongside the two ceramic burners and the pressure went up to the 35 mark whilst under no load again and I could plainly see that Gerry s was the better burner owing to the fierce blue flame, so this led me onto installing the two with one ceramic burner it was all trial and error at that time. With the three burners in place PYRTE got up to pressure in around 12 minutes on the bench, but with the motor running she was down on pressure to the 20 mark very quickly. This called for more heat, so I ordered a further two of Gerry s burners and installed them with the disappointing ceramic ones quickly dispatched to the bin. With the four burners in place I found that with the extra heat being produced, I had to open the vent in the top plate a little to accommodate the extra gas flow, that way not creating improper combustion, and this was easily achieved by opening the gap up to ¾ inch wide from its original ⅝ inch. I now use four of Gerry s burners, sitting half an inch under the boiler barrel and run from two gas bottles with the taps connected to a rubber gas hose between the trailer and the manifold, and this gets up steam and ready for the off in around 8 minutes from cold, and then once the steam s up, it s a case of turning off one bottle completely and using a single one, or turning the two down to suit the demand. Like this a single bottle will give almost an hour in running time. One word of caution here though... These fittings, the gas tap outlet thread and the piping nuts all have ¼ x 32tpi threads and for this reason you can either purchase the thread converter (adapter) from Gerry to bring these fittings to match the ¼ x 40tpi you are generally using, or you can source your own taps and dies (I suggest MaccModels) at ¼ x 32tpi to make up the manifold. Right... Enough of the waffle... Take your firebox base at 6 x 6 inches x ¹/₁₆ inch mild steel sheet and mark along two opposite sides a line at ³/₁₆ in from the edges. Along this line from each end make a mark at 1¼ inches in and drill through with a 3.5mm at these four points and sit the two ⅜ square brass rods you already have from your tender sides to sit flush with the ends and across the top of these and using the base as a guide, mark the brass rods for drilling purposes and drill right through. Now you need two 6 inch lengths of 1 inch x ⅛ section steel and drill a 3.5mm hole through the ends centrally, but at ³/₁₆ from the end and thread a 1 inch 4ba bolt through each hole from the bottom of the base plate, up through the brass rod and through the 1 inch x ⅛ support plates. This will leave you with ¾ inch of brass rod showing at either end, but do not worry about the middle bolts showing along the brass rods for now. (The above picture does not show this clearly or to scale as in these early trials with the gas heating, the brass rods here were simply butted together rather
5 than overlapped at the corners, but make a point of getting the rods the right way round as these need to be bolted to the inside of the firebox base). So you now have a base plate that can be mounted underneath the firebox and can be held in place with 6 x 4ba bolts. To make the all brass manifold, take 2 x 2 inch lengths of ¼ o/d brass rod and drill them through with a ⅛ drill. (You may need to drill in from both ends to complete this operation, although you can reduce the length of the rod, but it will mean the feed pipes for the burners being pulled into tighter bends to achieve this). The ends are threaded ¼ x 32 to accept the burner fittings (or alternatively ¼ x 40 with the adaptors from Clevedon Steam). Next you want 2 x 1¾ inch pieces of brass at ⅜ diameter with a ³/₁₆ hole bored to 1 inch deep. In the undrilled end a hole needs boring across the ⅜ rod to allow the ¼ tube to be inserted and silver soldered into place. Once this soldering is done, then a ³/₁₆ drill is used to continue the hole already started and to go through the side of the ¼ tube and marry up to the ⅛ holes in that tube, that way allowing gas to enter the larger diameter and escape at the two smaller ends and on to the burners. The hex rod is ¾ inch across the flats (I used hex as it was available and is easier to drill through sideways than round bar) and is 2 inches long with around ¾ inch turned to ¾ diameter (this is not really needed). A hole needs boring through across the flats at ½ an inch from the end for the ⅜ tubes to be soldered in place and from the round end of the hex rod a ¼ hole is needed to marry up to the ⅜ tubes. Open this ¼ hole out to ⅜ for a depth of ¼ inch to take a ⅜ brass tube which is soldered to it and held in place by the brass brackets supporting the burner stems. The supporting tube is again soldered to a length of 9 inch length (variable) ¼ inch o/d copper piping to allow easy access for coupling up the rubber gas hose from the trailer. This was achieved through a brass ferule being soldered on the end and a jubilee clip clamping the rubber tube to the ferule.
6 The burners themselves were purchased from Clevedon Steam and were simply clamped in place by the ⅜ inch square brass rods (remnants of the reinforcing rods in the fire box build). These rods were bolted to the raised 6 inch length of 1 inch x ⅛ section steel at the rear. block off the air inlet holes. You ll notice that lumps have had to be cut out to allow nuts to be placed on the bolts in the picture, plus some drilling will need to be done to get the burner necks to fit, but do make sure you do not In the above picture you can see an upper hole level with the two burner gas inlet points. This was the original mounting for the manifold and the flame sat far too low below the boiler, so the extra packing was installed to get the burners sat at around ½ an inch below the boiler bottom. You will also see that the ⅜ support tube for the gas supply is hex and has a threaded adapter for the copper tube - this was purely for my convenience and is not really needed. The piping for the gas is the same as supplied by caravan retailers, being re-inforced rubber hose with an internal diameter of just under ¼ inch (6mm I think). Because of this the end of the pipe sitting underneath the traction engine needs to be made to fit this and I made a simple brass ⅜ end soldered onto the ¼ inch pipe, with a reduction down to ¼ for the hose and bored through with a ³/₁₆ drill. On the bottle side of the equation, if you want to try a single gas bottle, then you need to make an adaptor with a ³/₁₆ diameter hole through it to go from the ¼ x 32 fitting on the end of the gas delivery tube from the bottle, onto a ¼ insert for the end of the rubber tube. This will not be too successful as you will see the gas delivery tube is ⅛ copper tubing with an internal diameter of ¹/₃₂ or there abouts, and as the pressure is not too high in these bottles, then this piping will restrict the amount of gas being fed to your burners. This size just about copes with 3 burners, but struggles with the 4 we are using for PYRTE. A simple T adaptor sitting in your trailer is all that s needed with a ¼ leg for the rubber tube end and two gas bottles individually feed the top arms of the T so that double the gas volume is available when needed. The arms are ¼ o/d with a bore of ⅛ and the leg is ¼ o/d with a bore of ³₁₆. At start-up both bottle are needed for the initial heat surge, but when she s warmed up a bottle can be turned down or off on the can and a single one provides enough heat for steady running. With the burners pointing towards the central axis of your boiler, all that s needed now is to connect your gas supply and light the burners so that you can adjust the flames properly. This is done by undoing the screw on the side of the gas inlet and sliding the jet holder either forwards or backwards to produce a large and neat blue flame what this does is to allow the correct amount of
7 air in the air hole by partly blocking it off (and causing some turbulence for better mixing at the same time). We next move on to the insulation and painting of your model.
TCWS54 SEE THRU DIAMOND BURNER INSTALLATION KIT INSTRUCTIONS
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationTCWS.38NG03.C BLACK DIAMOND BURNER KIT INSTRUCTIONS
IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER These instructions are supplementary to the Installation and Operating Instructions supplied with the fireplace and should be kept together.
More informationINSTALLATION INSTRUCTIONS TOWNSEND
INSTALLATION INSTRUCTIONS TOWNSEND.00 DECK MOUNT BATH FILLER.0 Thank you for selecting American Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-please
More informationGas Conversion Kits and Instructions
Gas Conversion Kits and Instructions INSTALLATION FORM RGM 432/433-GC (Version D.1) Obsoletes Form RGM 432/433-GC (Version D) APPLIES TO: Model FT and Model SFT All gas conversion must be done by a qualified
More informationManufactured in New Zealand Metal Fab Industries Ltd PO Box Greenmount Auckland
Manufactured in New Zealand Metal Fab Industries Ltd PO Box 58-473 Greenmount Auckland Www.metalfab.co.nz LOGAIRE STAINLESS STEEL BBQ 2,3 & 4 Burner Models IMPORTANT Please read all instructions before
More informationGas Go Anywhere /23/01
Gas Go Anywhere 55014 02/23/01 FOR OUTDOOR USE ONLY This grill does not include an LP fuel tank. Check Package Contents You should have received the parts listed below. While we give much attention to
More informationAuxiliary 63.5l Fuel Tank Ford/Mazda Pick-up Truck 2012-Current READ ME! IMPORTANT WARNING!
Auxiliary 63.5l Fuel Tank Ford/Mazda Pick-up Truck 2012-Current ENG FTFM006 90 min READ ME! Thank you for purchasing a Front Runner Ford/Mazda Pick-Up Truck 2012 - Current Fuel Tank. Before you start,
More informationInstructions for Converting Range to Operate on Liquefied Petroleum Gas
INSTALLATION AND SERVICES MUST BE PERFORMED BY A QUALIFIED INSTALLER IMPORTANT: SAVE INSTRUCTION MANUAL FOR THE LOCAL INSPECTOR S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE This conversion
More informationInstallation Instructions
THE COLLECTION by Installation Instructions 0 BIDET FITTING Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please
More informationCabinet Mount Assist Lift n Lock Instructions
Cabinet Mount Assist Lift n Lock Instructions PART LIST 2 @ Gas Cylinder 1 @ Lock Bar 2 @ Rubber Sleeve (preset) 4 @ Stopper Pin (2pcs preset) 4 @ Saddle Block 8 @ 19mm Black PVC Cap 5 @ 14mm Black PVC
More informationAdvantage Plus TIM-3600 Series Reel
Read the following precautions and instructions before you begin assembly or using. Failure to comply with these instructions could result in personal injury or property damage. Keep these instructions
More informationFORCE 10 MARINE BARBEQUES
FORCE 10 MARINE BARBEQUES PROPANE MODELS Model 3500 % Large Propane Model 3550 % Small Propane OWNER S MANUAL AND WARRANTY FORCE 10 MARINE LTD. 23080 Hamilton Road, Richmond, B.C. Canada V6V 1C9 Telephone
More informationGenesis. Side Burner Accessory Installation. Step 3. Step 1. Step 2. For use with Genesis Gas Barbecues Only
Genesis Side Burner Accessory Installation For use with Genesis Gas Barbecues Only Step 1 WARNING: All gas controls and supply valves should be in the OFF position. You will need: Side burner assembly
More informationπ H-3505 GARAGE CANOPY PARTS SAFETY uline.com TOOLS NEEDED 10' X 20' X 8'
π H-3505 GARAGE CANOPY 10' X 20' X 8' 1-800-295-5510 uline.com TOOLS NEEDED Safety Glasses Wrench or Socket 9/16" or 14mm Tape Measure Phillips Screwdriver Rubber Mallet PARTS Cables x 5 2-way Corner Foot
More informationAssembly Instructions
Assembly Instructions Thank You for your purchase of this conversion kit, we hope it makes your Media Blasting experience much more enjoyable. This kit was designed primarily to convert the Harbor Freight
More informationSERVICE MANUAL V-SERIES HEAVY DUTY BROILERS, DOUBLE DECK AND RANGE MATCH MODELS - NOTICE - For a complete listing of models, see the MODELS section.
SERVICE MANUAL V-SERIES HEAVY DUTY BROILERS, DOUBLE DECK AND RANGE MATCH MODELS For a complete listing of models, see the MODELS section. - NOTICE - This Manual is prepared for the use of trained Vulcan
More informationHow to Set up Your Configurable (Home and Camping) Stir Fry Stove
How to Set up Your Configurable (Home and Camping) Stir Fry Stove Setting up the outdoor stir fry stove is quick and easy. However, EXERCISE EXTREME CAUTION and apply common sense -- you are dealing with
More informationTC42 TRANQUILITY BURNER KIT INSTRUCTIONS
IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER These instructions are supplementary to the Installation and Operating Instructions supplied with the fi replace and should be kept together.
More informationTherme storage water heater. Table of contents. Symbols used. Symbols used Symbol indicates a possible hazard. Installation instructions
Therme storage water heater Table of contents Symbols used... 8 Installation instructions Water supply... 9 Choice of location... 9 Installation of the Therme... 9 Fitting the draining and venting valve...
More informationInstructions for Converting Range to Operate on Liquefied Petroleum Gas
INSTALLATION AND SERVICES MUST BE PERFORMED BY A QUALIFIED INSTALLER IMPORTANT: SAVE INSTRUCTION MANUAL FOR THE LOCAL INSPECTOR S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE This conversion
More information3/8 BORE MOUNTING BRACKETS
3/8 BORE MOUNTING BRACKETS 11767 Ceramic Insulator Use with cylinder having #8-32 threaded shaft to insulate cylinder from heat or electricity #8-32 thd. - thru dia. Male Clevis 11996 Mounts in rear of
More informationTC36 CHALET BURNER KIT INSTALLATION INSTRUCTIONS
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationPROPANE LANTERNS LIMITED WARRANTY. All propane lanterns carry a
PROPANE LANTERNS 14201 14201 Single Mantle Propane Lantern Adjusts to 300 candlepower illumination Valve adapter Burns 8 hours at maximum setting 14202 14202 Double Mantle Propane Lantern Adjusts to 600
More informationTCWS54 SEE THRU LONG BEACH LOG INSTALLATION INSTRUCTIONS
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationStainless Steel Combined Drinking Fountain With Bottle Filler
Stainless Steel Combined Drinking Fountain With Bottle Filler Product Code WH-DFBF-WRAS Stainless steel wall mounted drinking fountain with bottle filler spout. WRAS approved drinking water bubbler (tap)
More informationSuggested tools: Flat head screw driver, power drill, ¼ drill bit, 24 level, and a tape measure. HARDWARE LIST (2) FUEL CANISTER HOLDER
SOUTHERN ENTERPRISES INC. This product has been engineered for easy installation and is constructed for durability. Please take the time to read through and follow these assembly instructions. YOU CAN
More information300 ft. 5/8 Hose wagon
300 ft. 5/8 Hose wagon Model 95956 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. (Garden hose is not included).
More informationLOUISIANA BURNER / The Millers and the staff of Louisiana Burner
Louisiana Burner 634 Main Street Pineville, LA 71360 318 318--473 473--2868 Fax 318 318--473 473--2807 www.louisianaburners.com catalog2016 LOUISIANA BURNER Dear Customers, Last year, the Miller Family
More informationAssembly TOOLS REQUIRED: 17mm and 14mm or equivalent wrenches.
Instructions for 3 Trimmer Rack, 3TR* *Patents Pending Assembly TOOLS REQUIRED: 17mm and mm or equivalent wrenches. 15 26 26 16 15 16 Attach the lower mounting brackets to the Trimmer Rack poles as shown
More informationUrea/Adblue Hose Reel
www.scintex.com.au sales@scintex.com.au Model: SHR3408 Urea/Adblue Hose Reel Product Manual Specifications Spring driven drum: for automatic rewind. Locking ratchet: to maintain the desired length of hose
More informationPropane Accessories. Call or Houston, Texas:
14210 Lantern Mantles For single or double mantle propane lanterns Two mantles per poly bag and 50 bags per counter display box Propane Accessories 14208 Glass Lantern Globe Heat resistant replacement
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationAssembly/Installation/Use Instructions:
IMPORTANT We highly recommend that our products be installed and serviced by professionals who are certified in the U.S. by NFI (National Fireplace Institute) or in Canada by WETT (Wood Energy Technical
More informationNew Intercooler O-Rings fitted Viton CDT/CDTI... By Arctic
New Intercooler O-Rings fitted Viton CDT/CDTI... By Arctic The intercooler is located at the bottom of the main radiator, and this is how it is possible to replace the O-rings with out taking the bumper
More informationInstallation and Maintenance Manual
Freestanding Gas Stove MODEL: PGS2005 GPEBB20R GPEBW20R Installation and Maintenance Manual Warning Maintenance products should be carried out by professional and technical personnel with relevant qualification,
More informationTC30 BLACK DIAMOND BURNER KIT INSTRUCTIONS
IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER These instructions are supplementary to the Installation and Operating Instructions supplied with the fi replace and should be kept together.
More informationInstructions for Building the MIDGE (Modified Inverted Downdraft Gasifier Experiment)
Instructions for Building the MIDGE (Modified Inverted Downdraft Gasifier Experiment) Materials: - 55 oz Bush Beans can, or similar. - 16 oz tomato can, or similar. - Large tuna can (12oz), or other can,
More informationFor converting 72 PKN for use with (LP) propane gas.
IMPORTANT READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING These instructions must be used as a supplement to the instructions supplied with your gas log set. Follow the Gas Log Set instructions
More informationAuto Rewind Hose Reel 10M / 20M / 30M Models
Auto Rewind Hose Reel 10M / 20M / 30M Models Instruction Manual 10M / 20M / 30M Auto Rewind Hose Reel Installation, Hose Replacement and Troubleshooting Guide Product Codes: 1110H / 1120H / 1130H Models
More informationTCWS54 BLACK DIAMOND BURNER KIT INSTRUCTIONS
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationINSTALLATION AND OPERATION GUIDE FOR
INSTALLATION AND OPERATION GUIDE FOR Featuring Aquatic Glassel Tempered, Formulated Glass, 2005-2007 NATURAL GAS INSTRUCTIONS Adequate Fireplace Ventilation is Required NOTE: READ INSTRUCTIONS FULLY BEFORE
More informationOtter XT 650 Cabin Installation and Set-Up Instructions
Otter XT 650 Cabin Installation and Set-Up Instructions Otter XT 650 Cabin Fits Medium Otter Wild Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Otter XT 650 Cabin 200891 2 1
More informationSPK3E - Manual EASY Control
SPK3E - Manual EASY Control General Assembly, Installation, and Operation Instructions for use with Natural Gas Burners; F, FX, CS, CXF, TNA or Propane Gas Burners: FA, FAX, CA, CXFA, TNA/LP LISTED BY
More informationLP Grill and Gas Hose
Tales from the Fox s Den Volume 1 7/2011 LP Grill and Gas Hose This seems to be a reoccurring theme on the forum and Internet about propane grills, quick disconnects, hoses, and what to do. First of all
More informationTUBULAR BURNER CONVERSION KIT AGCK-TBXX / AECK-UBXX
TUBULAR BURNER CONVERSION KIT AGCK-TBXX / AECK-UBXX IMPORTANT - READ ALL INSTRUCTIONS BEFORE YOU BEGIN THE INSTRUCTIONS HEREIN SHOULD BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. THE GRILL MUST BE COMPLETELY
More informationINFRARED BURNER KIT INSTRUCTIONS
6 4 3 2 INFRARED BURNER KIT INSTRUCTIONS 1 Model # 3049 (A790, A660, & A530) Model # 3051 (A540, & A430) Included parts 5 NOTE: This unit has been retrofi tted with an infrared burner. PARTS INCLUDED 1.
More informationInstallation Guide: Round Trampoline
Trampolines & trampoline parts designed to survive in the harsh Oz climate. www.oztrampolines.com.au Installation Guide: Round Trampoline Safety Tips Here at Oz Trampolines we are passionate about your
More informationCapacity kw. Thermal turndown from specified maximum capacity 8:1 8:1
3-18.3-5 Specifications of OXY-THERM TITAN burners Typical burner data Fuel: natural gas at 15 C with 10.9 kwh/nm 3 HHV - sg = 0.6 Oxygen: 90-100% purity Stated pressures are indicative. Actual pressures
More informationINSTALLATION INSTRUCTIONS AND OWNER'S MANUAL AWNINGS. For trailers & motor homes with straight sides TOOLS REQUIRED
AWNINGS INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL For trailers & motor homes with straight sides TOOLS REQUIRED 1/4" electric drill Ratchet handle kit 3/8" & 7/16" socket No. 1 and No. 2 screwdriver
More informationREPLACEMENT PROCEDURE: ROTISSERIE ORIFICE: TOOLS REQUIRED TO INSTALL THIS KIT: ITEM DESCRIPTION: E C
TOOLS REQUIRED TO INSTALL THIS KIT: ITEM DESCRIPTION: A SCREWDRIVER - PHILIPS SIZE # 2 B SCREWDRIVER - FLAT 1/8 WIDE TIP C 1/2 WRENCH - OPEN TYPE D 7/16 WRENCH - OPEN TYPE E RATCHETING SOCKET WRENCH -
More informationINSTALLATION GUIDELINES
IMPORTANT: To ensure this product is installed properly, you must read and follow these guidelines. The owner/user of this product must keep this information for future reference. This product must be
More informationRMC1E - Variable Flame Height EASY Control
Owner s Manual RMC1E - Variable Flame Height EASY Control General Assembly, Installation, and Operation Instructions for use with Natural Gas Burners; F, FX, CS, CXF, TNA or Propane Gas Burners: FA, FAX,
More informationCONVERSION INSTRUCTIONS
CONVERSION INSTRUCTIONS Natural Gas to Propane Gas Conversion Kit For Thermador Professional Cooktops and Ranges Model STARLPKIT Part No. 35-00-682 Contains 7mm Hex Main Orifices This kit is used to convert
More informationREAD ME FIRST! IMPORTANT WARNING! ENG. Roof top tent
Roof top tent ENG TENT031 220 min READ ME FIRST! Thank you for purchasing a Front Runner Roof Top Tent. Before you start, take a moment to familiarize yourself with these Fitting Instructions and the components
More informationThe safe & affordable install
QSLG1000 Quick-Sling SPECS QSLG1000 Each arm attaches to wood using 2 zip screws for stability & a 4 through bolt & wing nut for security. Installs to steel using steel beam adapters. 28 points of anti-vibration
More informationr e - p a r t s. c o m
Owner s Manual SPK3E - Manual EASY Control General Assembly, Installation, and Operation Instructions for use with Natural Gas Burners; F, FX, CS, CXF, TNA or Propane Gas Burners: FA, FAX, CA, CXFA, TNA/LP
More informationTC36 COUNTRY HOME BURNER KIT INSTRUCTIONS (NATURAL GAS ONLY)
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationContents. Company Background FLOWSTOPPER Plugging Device Kit and Replacement Parts Key Features & Benefits... 4
Contents Company Background... 2 FLOWSTOPPER Plugging Device Kit and Replacement Parts... 3 Key Features & Benefits... 4 Frequently Asked Questions... 5 Step by Step Instructions... 6 FLOWSTOPPER Warranty...
More informationBROEN UNIFLEX FITTINGS FOR WATER BROEN UNIFLEX TM FITTINGS FOR WATER
BROEN UNIFLEX FITTINGS FOR WATER TABLE OF CONTENTS Content Page Table of Contents 2 BROEN UniFlex TM BASIC 4 Product Overview 5 Water Fittings Bench Mounted Fitting with Swivel Spout... 6 Single Handle
More informationINSTRUCTIONS FOR MVK-NQM PILOT KIT
MVK-NQM IMPORTANT READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING These instructions must be used as a supplement to the instructions supplied with your gas log set. Follow the Gas Log Set instructions
More informationSwagelok Thermoplastic Hose Hand Swager User s Manual
Swagelok Thermoplastic Hose Hand Swager User s Manual Thermoplastic Hose Hand Swager User s Manual Contents Hand Swager Components....................... 2 Setup Swager.......................................
More informationInstructional Booklet
Instructional Booklet 936-894-3292 Thank you for choosing The Bathmaster! You are on your way to creating an unmatched bathing experience both for you and the lucky animal. The Bathmaster is designed to
More informationTC42 CHALET BURNER KIT INSTALLATION INSTRUCTIONS
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationSteadiCam Parts List*
SteadiCam Parts List* A. 1 Bogen 3232 Monopod Swivel Tilt Head B. 1 1/2 internal to 1/2 external brass bushing flare adapter (part 9402249 at osh.com¹) C. 2 3/8 internal to 1/2 external brass bushing flare
More information* * 4023 KR. Step 1 Prepare the Keyed Removable Unit. Not for use on electric or fire rated removable mullions
condition. *64009-00* 64009-00 Keyed Removable Mullions 403 KR Installation Instructions Not for use on electric or fire rated removable mullions This kit includes the following parts: (Not to scale) 5/6
More informationReverse Osmosis system 50 GPD Instruction manual EN
Reverse Osmosis system 50 GPD Instruction manual EN Contents 1. Unpacking 2. Scope of supply 3. Insertion of the membranes 4. Connecting the lines 5. Installation 6. First commissioning 7. Consumables
More informationECLIPSE AIR HEAT BURNERS Series AH-O & TAH-O
ECLIPSE AIR HEAT BURNERS Series AH-O & TAH-O U.S. Reissue Pat. No. 26,244 Canadian Pat. No. 743,782 Spec 144 11/4/03 AH-O, Front View Data 144-1 AH-O, Back View Data 144-1 TAH-O, Front View Data 144-2
More informationWIDESPREAD LAVATORY MODELS WITH HI-ARC SPOUT
5951, 5961, 5981, 5983, 5993 SERIES MT122B INSTALLATION INSTRUCTIONS THESE INSTRUCTIONS MUST BE LEFT WITH HOMEOWNER WIDESPREAD LAVATORY MODELS WITH HI-ARC TRADITIONAL CROSS NOTE: Handle Inserts are not
More informationPro 88/86. The classic torch system. All components are carefully chosen to guarantee long service life. Ergonomic designed handles
The classic torch system All components are carefully chosen to guarantee long service life Ergonomic designed handles Works in all weather conditions Wide range of burners for all applications Pro 88
More informationVALORE SEVEN. Serial Number. Pacific) Version No.:V
VALORE SEVEN Version No.:V.206222 Serial Number Pacific) 7 9 8 " 5 8 " " 7 2 8 " 26 2 " 7 8 " 9" 2 8 " 2 8 " (H) 26.9" x (W) 8.26" x (D) 8.85" Hand shower hose: 59.05" Weight: Net: 0 lbs /Gross: 2 lbs
More informationASSEMBLY GUIDE. Customer Service: INCH² 2-BURNER & 864 INCH² 2-BURNER
ASSEMBLY GUIDE 688 INCH² 2-BURNER & 864 INCH² 2-BURNER DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open lid. 4. If odor continues, keep away from the appliance
More informationINSTRUCTION MANUAL ALEKO RETRACTABLE AWNING
INSTRUCTION MANUAL for ALEKO RETRACTABLE AWNING www.alekoproducts.com FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY! 1 Important Safety Precautions WARNING NOTE: FOR PERSONAL SAFETY,
More informationFor draining expansion tanks, other liquid storage vessels.
Plumbing Specialties 26-100 & 26-300 SERIES COMPRESSION GAUGE COCKS For draining expansion tanks, other liquid storage vessels. 26-100: rated up to 125 psig 26-300: soft metal seat/stuffing box rated up
More informationOtter Pro XT 1200 Cottage Installation and Set-Up Instructions
Otter Pro XT 1200 Cottage Installation and Set-Up Instructions Otter Pro XT 1200 Cottage Fits Small Ultra-Wide Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete
More information280 Propane Barbecue Assembly Manual
280 Propane Barbecue Assembly Manual 85-3001-8 (G20718) Propane 1 Year limited Warranty Read and save manual for future reference. Assemble your grill immediately. Missing or damaged parts claims must
More informationAutomated Tiki Torch Installation Instructions
Automated Tiki Torch Installation Instructions Automated Tiki Torch with Poles (Exploded View) 14 Automated Tiki Head 6 8 Tiki Pole (Powder Coated Aluminum or Faux Bamboo Pole) 18 Base Pole (Powder Coated
More informationAssembling A Pennine Awning: A Pictorial Guide Below is a step by step pictorial guide to setting up a Pennine awning. This guide is based on the older, heavy duty awning poles, and the smaller awning
More informationStrut Clamp Pipe & Conduit
PRODUCT SPECIFICATIONS 0F Strut Clamp Pipe & Conduit Size: Steel pipe sizes 2" through 0" Finish: Electro-Galvanized Pipe clamps are designed to fit into the opening of 5 /8" wide channel profiles Pre-Assembled
More informationInstallation instruction
Installation instruction Ci51 116 FACTS Technical specifications Model i51 Log box (option) Output 6-11 kw Nominal output 8 kw Efficiency 80 % Weight (kg) 215 50 Powerstone (option): + 100 kg Width (mm)
More informationORIGO 1500, 3000 ORIGO 6000, 6100, Alcohol stoves Operating manual Spirituskocher Bedienungsanleitung... 24
C C _Origo_5 6.book Seite Freitag,. Dezember 8 : 5 EN Alcohol stoves Operating manual............... 8 DE Spirituskocher Bedienungsanleitung............ ORIGO FR ES Cuisinières à alcool Notice d utilisation..............
More informationUNODOS + / FLOCDOS +
Operation manual UNODOS+ / FLOCDOS+ (01-09) page 1 of 7 UNODOS + / FLOCDOS + Table of contents page 1. Technical description... 2 1.1 The function... 2 1.2 Technical details... 2 1.3 The dosing performance...
More informationVoice Mail: (815) Fax: (815) OWNERS MANUAL
www.countryhomescampers.com Email: info@countryhomescampers.com Voice Mail: (815) 346 3337 Fax: (815) 346 3337 OWNERS MANUAL Introduction: Your Country Homes Camper has been engineered and built with a
More informationASSEMBLY GUIDE. Customer Service: INCH² 3-BURNER & 545 INCH² 3-BURNER
ASSEMBLY GUIDE 455 INCH² 3-BURNER & 545 INCH² 3-BURNER DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open lid. 4. If odor continues, keep away from the appliance
More informationLITE Spear Awning Instructions
LITE Spear Awning Instructions IMPORTANT NOTE: Please take a few minutes to become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and
More informationTCWS.54NG03C2 BLACK DIAMOND BURNER KIT INSTRUCTIONS
IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER These instructions are supplementary to the Installation and Operating Instructions supplied with the fi replace and should be kept together.
More informationDevelopment and performance of the common Keren Stove Yogyakarta, November 2012 March C Pemberton Pigott
Development and performance of the common Keren Stove Yogyakarta, November 2012 March 2013 C Pemberton Pigott 1. Overview: 1.1. The Keren stove is the most common single pot cooking device in Central Java.
More informationStandard Awning Installation Instructions
Standard Awning Installation Instructions Important Note: Please become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and will make
More informationGoBidet Bidet Attachment
GoBidet Bidet Attachment 151 Ruths Place #5 Sequim, WA 98382 Tel 1-800-681-0753 Fax +1 360-681-4029 www.go-bidet.com MODEL #2003C In this box: 1 User Manual 1 GoBidet Unit w/ mounting bracket, nut, rubber
More informationEEZI - AWN series 1000 / 2000 Awning bracket
EEZI - AWN series 1000 / 2000 Awning bracket RRAC063 INSTALL TIME: 15 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
More informationPARTS LIST EXTRACTOR ACCESSORIES
PARTS LIST EXTRACTOR ACCESSORIES 3 - JET WAND - 4097101 101 4097961 HANDLE ASSEMBLY - INCLUDES: 1 102 9121210 1/4-20 X 5/8 HEX BOLT 2 103 ---------- HANDLE CLAMP 1 104 9120920 1/4-20 HEX NUT 2 105 9120777
More informationThermostatic Griddle Field Service Kit Instructions
Thermostatic Griddle Field Service Kit Instructions The following document provides instructions on how to install a Garland Thermostatic Griddle Field Kit and is applicable to each 2 section of a Garland
More informationTC36 CHALET II BURNER KIT INSTALLATION INSTRUCTIONS
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationTools. For safety and easy faucet replacement, San-Ei recommends the use of the following helpful tools:
BW-0BH INSTALLATION INSTRUCTIONS SINGLE HANDLE Kitchen Faucet Tools For safety and easy faucet replacement, San-Ei recommends the use of the following helpful tools: SAFETY GLASSES PIPE WRENCH PLIERS CHANNEL
More informationDeep Cleaning a Passap is a three step process: Tear down, Clean, and Reassemble.
kni!sings Deep Clean A Passap Duomatic Deep Cleaning a Passap is a three step process: Tear down, Clean, and Reassemble. I won t mislead you. Your nerves will be on edge while you take apart your precious
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS KR54, KR1654, & KR4954 Keyed Removable Mullion NOT FOR USE ON ELECTRIC OR FIRE RATED MULLIONS. This kit includes the following parts: (Not to scale) WARNING Remove key, reinstall,
More informationVirto - the flexibility of a natural shape.
- the flexibility of a natural shape. 118 Wash basin Model no.: 252560 Dimensions: 600 x 480 mm Weight: 13,6 kg model no. 291700, model no. 291800, or wash basin boxette, model-no. 876411, of the bathroom
More information14' x 32' x 12' Round Top Round Style Shelter Assembly Instructions
14' x 32' x 12' Round Top Round Style Shelter Assembly Instructions Description Model # 14' x 32' x 12' RoundTop Garage - Gray 62669 Recommended Tools Please read instructions COMPLETELY before assembly.
More informationmade by made by NEW UK 17/18
NEW made by A true Viking Raw strength and strong family ties are classic symbols of the Scandinavian Vikings. These symbols also provide the foundation for our WIKING stoves, which radiate high quality
More informationGetting Started Guide
Getting Started Guide Assembly Instructions User Guide Table Top Maintenance Warranty Information (800) 445-4559 www.designingfire.com Fax: 651-305-6347 @designingfire.com #253915-2528907 Installers: Please
More informationTC36 SEE-THRU CHALET BURNER KIT INSTRUCTIONS
IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER These instructions are supplementary to the Installation and Operating Instructions supplied with the fi replace and should be kept together.
More information