USER S MANUAL MANUAL DE USUARIO 3 DMX CHANNELS MODES CONTINUOUS BLINDER EFFECT PREPROGRAMED SPECIAL EFFECTS
|
|
- Gervase Moore
- 5 years ago
- Views:
Transcription
1 USER S MANUAL MANUAL DE USUARIO 3 DMX CHANNELS MODES CONTINUOUS BLINDER EFFECT PREPROGRAMED SPECIAL EFFECTS
2 SAFETY INFORMATION To guard against electric shock Disconnect the fixture from AC power and allow the flash capacitor to discharge for 1 minute before changing the lamp or fuse, and when not in use. Do not remove the rear cover: there are no user-serviceable parts inside. Always ground (earth) the fixture electrically. Do not expose the fixture to rain or moisture. Replace the lamp only as described or have it replaced by a Strobe service technician. To guard against UV radiation, burns, and fire Never operate the fixture with the front glass open, missing or damaged. Do not stare directly into the light. Never look at an exposed lamp while it is lit. Replace the lamp when it becomes defective or worn out. When replacing the lamp, allow the fixture to cool for at least 10 minutes before opening the fixture or removing the lamp. Never attempt to bypass the fuse. Always replace defective fuses with ones of the specified type and rating. Keep all combustible materials (for example fabric, wood, paper) at least 0.5 meters (20 inches) away from the fixture. Keep flammable materials well away from the fixture. Do not illuminate surfaces within 1 meter (39 inches) of the fixture. Provide a minimum clearance of 0.1 meters (4 inches) around air vents. Never place filters or other materials over the front glass cover. The exterior of the fixture can reach temperatures up to 120 C (248 F). Allow the fixture to cool for at least 15 minutes before handling. Do not operate the fixture if the ambient air temperature (Ta) exceeds 40 C (104 F). Note: Avoid extended periods of continuous flashing, particularly at frequencies of 10 to 20 flashes per second EN 1
3 TO INSTALL THE MOUNTING BRACKET 1.- Place the fixture face down on a table 2.- Place a plastic washer on each mounting bracket stud 3.- Place one end of the bracket on one of the mounting studs. Bend the other end of the mounting bracket open slightly and work it onto the opposite stud 4.- Place a hand knob on each stud. Tighten both hand knobs to lock the mounting bracket in place DMX OPERATION DMX connection The FS-3000D provides both 3-pin and 5-pin XLR sockets for data connection. The pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5. The sockets are wired in parallel: both inputs connect to both outputs. For reliable data transmission use one input and one output! DMX link 1. Connect the DMX data input from the controller to the FS-3000D s 3-pin or 5-pin input (male) socket. 2. You can connect up to 31 additional fixtures output-to-input. 3. Insert a termination plug in the output of the last fixture on the link. EN 2
4 DATA CONNECTION TIPS Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit control data reliably over long runs. 24 AWG cable is suitable for runs up to 300 meters (1000 ft.). Use heavier gauge cable and/or an amplifier for longer runs. Never use both outputs to split the link. To split the serial link into branches use a signal splitter. Do not overload the link. Up to 32 devices may be connected on a serial link. Terminate the link by installing a termination plug in the output socket of the last fixture. The termination plug, which is a male XLR plug with a 120 ohm, 0.25 watt resistor soldered between pins 2 and 3, soaks up the control signal so it does not reflect and cause interference. DMX CONTROL MODES The DMX control options are selected on the Mode DIP switch 1 Channel DMX mode allows you to strobe from 0 flashes per second to the maximum flash rate and trigger the blinder effect from the controller. To select 1ch DMX operation, set pin 5 of the mode DIP switch to ON; set pins 1 to 4 to OFF 3 Channel DMX mode provides control of flash intensity, flash duration and flash rate for more advanced control than 1 channel mode. To select 3 channel DMX operation, set pins 1 to 5 of the mode DIP switch to OFF. 4 Channel DMX mode provides six special effects in addition to flash intensity, duration and rate control. To select this 4 ch DMX operation, set pins 1,2,3 and 5 to OFF,set pin 4 to ON CONTROL ADDRESS The control address, also known as the start channel, is the first channel used to receive instructions from the controller. The adress may be any channel from to 1 to 511 and is set on the address DIP switch. The FS-3000D uses 1,3 or 4 channels depending on the control mode. For independent control, each fixture must be assigned its own address and nonoverlapping control channels. Two or more FS-3000D may share the same address if individual control is not required. EN 3
5 To set the DMX address 1.- Select an address for the fixture on your controller. Look up the DIP switch setting for the address in the table below 2.- Set pins 1 through 9 ON (1) or OFF (0) as listed in the table. Set pin 10 to OFF Find the address in the table. Read the settings for pins 1-5 to the left and read the settings for pins 6-9 above the address. 0 means OFF and 1 means ON. Pin 10 is always OFF for DMX operation. EN 4
6 Channel 2 Channel 14 Channel 46 Channel 100 DMX CONTROL SUMMARY INTENSITY Flash intensity can be set from minimum (blackout) to maximum on channel 1 in the 3- and 4-channel DMX modes. Intensity is maximum in 1-channel DMX mode. DURATION Flash duration can be set from 0 to 650 ms on 50 Hz power supplies, or 0 to 530ms on 60 Hz power supplies, on channel 2 in the 3- and 4-channel DMX modes. Flash duration is fixed in 1-channel DMX mode. RATE Flash rate can be set from 0 flashes per second to 25 flashes per second Hz on 50Hz power supplies, or from 0 to 30 flashes per second on 60 Hz power supplies, on channel 3 in the 3-and 4-channel DMX modes. Flash rate is also controllable in 1-channel DMX mode. PROGRAMMED EFFECTS Six programmed effects are available on channel 4 in the 4-channel DMX mode only. The effects may be altered using the intensity, duration, and rate controls. Ramp up: Light gradually increases in intensity, then blacks out. Ramp down: Light flashes to full intensity, then gradually fades. Ramp up-down: Light gradually increases and decreases. Random flash: Light flashes randomly with variable rate and intensity. Multiple units flash independently of each other. Lightning: The flashes simulate lightning. Duration is not adjustable. Spikes: The lamp remains dimly illuminated between flashes. Set flash intensity, duration, and rate as normal. BLINDER EFFECT The blinder effect, in which the light remains on for an extended period, is available in all DMX modes. In the 3- and 4-channel modes, the effect is achieved whenever the combination of flash duration and rate prevents pauses between flashes. For example, the blinder effect can be achieved with a flash duration of 0.25 seconds (250 ms) and a flash rate of 4 flashes per second, or a flash duration of 0.05 seconds (50 ms) and a flash rate of 20 flashes per second. In 3- and 4-channel DMX mode, the intensity of the blinder effect is controllable on channel 1. Lamp power is electronically regulated to prevent the lamp from overheating. The intensity falls as power is reduced. EN 5
7 SINGLE FLASH To trigger single flashes, start with the intensity and flash rate at 0 and then set an intensity on channel 1. When the value of channel 1 changes, the light will flash once with the programmed intensity, duration, and effect. STAND ALONE OPERATION STAND ALONE FLASH RATE To program stand alone execution 1.- Apply power to the fixture 2.- Set pin1 of the mode DIP switch to ON. Set pins 2-5 to OFF. Set pin 6 to ON for low power operation or to OFF for high power operation. 3.- Select either a flash rate or the blinder effect. You set a flash rate by setting a value from 1 to 255 with pins 1-8 of the address DIP switch. The value required to achieve a desired flash rate can be calculated as follows. DIP value = x AC frequency Flash rate To achieve a flash rate of 10 flashes per second on a 50 Hz AC power supply, for example, the DIP value is 251. To select the blinder effect instead, set pin 9 to ON. 4. Set DIP switch pin 10 to OFF for normally off operation, or to ON for normally on operation. EN 6
8 DMX PROTOCOLS 1 CHANNEL DMX MODE Channel Value Percent Function Blackout Flash rate,slow or fast Continuous Blinder effect 3 AND 4 CHANNEL DMX MODES Value Percent Function Channel Flash intensity Blackout Minimum to maximum Channel Flash Duration 0-650ms 50Hz AC 0-530ms 60Hz AC Channel Flash Rate No flash (single flash with ch.1) Hz 50Hz AC Hz 60Hz AC Note: Enable channel 4 with mode DIP switch no. 4 on Channel 4 Special Effects No effect Ramp up Ramp down Ramp up-down Random Lightning Spikes EN 7
9 INFORMACIÓN SOBRE SEGURIDAD Para protegerse de las descargas eléctricas Desconecte el aparato de la red eléctrica y permita que el condensador de destellos descargue durante 1 minuto antes de cambiar la lámpara o fusible. No quite la cubierta posterior: no hay piezas que el usuario pueda reparar. Siempre conecte a tierra (masa) el aparato eléctrico. No exponer el aparato a la lluvia ni a la humedad. Cambie la lámpara sólo como se describe o solicite su remplazo a un técnico. Para protegerse contra la radiación UV, quemaduras y fuego Nunca haga funcionar el aparato con el cristal frontal abierto o dañado. No mire directamente a la luz. Nunca mire una lámpara mientras esté encendida. Cambie la lámpara cuando esté defectuosa o desgastada. Al cambiar la lámpara, deje enfriar el aparato durante al menos 10 minutos antes de abrirlo. Nunca intente anular el fusible. Sustituya siempre los fusibles defectuosos por otros del mismo tipo y características. Mantener todos los materiales combustibles ( p.ej. tejidos, madera, papel) al menos 0,5 metros de distancia del aparato. Mantenga los materiales inflamables lejos del aparato. No iluminar superficies de menos de 1 metro del dispositivo. Dejar una distancia mínima de 0,1 metros de las salidas de ventilación del aparato. No colocar nunca filtros u otros materiales sobre la cubierta frontal de vidrio. El exterior del aparato puede alcanzar temperaturas de hasta 120 C ( 248 F). Dejar que el aparato se enfrie al menos 15 minutos antes de su manipulación. No utilice el aparato si la temperatura ambiente excede los 40 C Nota: Evitar largos períodos de parpadeo continuo, sobre todo en frecuencias de 10 a 20 destellos por segundo ES 8
10 PARA INSTALAR EL SOPORTE DE MONTAJE 1.- Coloque el dispositivo sobre una mesa 2.- Coloque una arandela de plástico en cada perno 3.- Coloque un extremo de la abrazadera en uno de los pernos de montaje 4.- Coloque las perillas de ajuste en cada perno Apriete las dos perillas de ajuste para bloquear el soporte de montaje FUNCIONAMIENTO DMX Conexión DMX El FS-3000D tiene conectores XLR de 3 pines y 5 pines para la conexión DMX. Los enchufes están conectados en paralelo: ambas entradas están conectadas a ambas salidas. Enlace DMX 1. Conecte la entrada DMX desde el controlador hasta la entrada de 3 pines o 5 pines del FS-3000D (macho). 2. Conecte hasta 31 dispositivos adicionales 3. Inserte un terminal en la salida del último dispositivo de la línea. ES 9
11 CONSEJOS PARA LA CONEXIÓN DMX El cable estándar de micrófono no puede transmitir datos de control correctos a demasiada distancia. No utilice nunca las dos salidas para dividir la línea. Para dividir la línea en serie de varias ramas utilice un Divisor de señal. No sobrecargue el enlace. Hasta 32 dispositivos pueden ser conectados en serie. Cerrar el circuito serie instalando un terminal XLR en la toma de salida del último dispositivo. MODOS DE CONTROL DMX Las opciones de control DMX se seleccionan en el Modo DIP switch Modo 1 canal DMX permite desde 0 destellos por segundo hasta la máxima velocidad de destello y activar el efecto Blinder desde el controlador. Para seleccionar la operación 1 canal DMX, fijar el interruptor de modo DIP pin 5 en ON ; establecer los pins del 1 al 4 en OFF Modo 3 canales DMX proporciona un control de la intensidad del flash, duración del flash y velocidad de destello para un mayor control que el modo de 1 canal DMX. Para seleccionar modo 3 canales DMX, pins del 1 al 5 en OFF. Modo 4 canales DMX proporciona seis efectos especiales, además de la intensidad del flash, la duración y control de la frecuencia. Para seleccionarlo, fijar los pines 1,2,3 y 5 en OFF, y el pin 4 en ON. DIRECCIÓN DMX La dirección de control, conocido también como canal de inicio, es el primer canal utilizado para recibir instrucciones desde el controlador. La dirección puede ser cualquier canal del 1 al 511. El FS- 3000D utiliza 1,3 o 4 canales dependiendo del modo de control. Para un control independiente, a cada aparato se le debe asignar una dirección propia y canales de control que no se superpongan. Dos o más FS- 3000D pueden compartir la misma dirección si no se requiere un control individual. ES 10
12 CONFIGURAR DIRECCIÓN DMX 1.- Seleccione una dirección para el dispositivo en el controlador. Busque la posición del DIP switch para la dirección en la tabla de abajo 2.- Fijar los pines del 1 al 9 en ON (1) u OFF (0) como se indica en la tabla. Pin Set 10 en OFF Busque la dirección en la tabla. "0" significa OFF y "1" significa ON. Pin 10 debe estar siempre en OFF para funcionamiento DMX. ES 11
13 Channel 2 Channel 14 Channel 46 Channel 100 CONTROL DMX INTENSIDAD La intensidad del flash puede ajustarse desde el mínimo ( blackout ) al máximo en los modos de 1, 3 y 4 canales DMX. La intensidad es máxima en el modo de 1 canal DMX. DURACIÓN La duración del flash puede ajustarse desde 0 hasta 650 ms en 50 Hz o de 0 a 530ms en 60 Hz, en los modos de 2,3 y 4 canales DMX. La duración del flash se fija en modo 1 canal DMX. FRECUENCIA la frecuencia del flash se puede ajustar de 0 destellos por segundo a 25 destellos por segundo en 50 Hz, o de 0 a 30 destellos por segundo en 60 Hz, en el canal 3,en los modos de 3 y 4 canales DMX. La frecuencia del Flash también se puede controlar en modo 1 canal DMX. EFECTOS PREPROGRAMADOS Seis efectos preprogramados están disponibles en el canal 4, sólo en el modo de 4 canales DMX. Los efectos pueden ser modificados en intensidad, duración y frecuencia. Ramp up : Aumenta gradualmente en intensidad, y luego cae. Ramp down : Destellos de luz a plena intensidad, y luego se desvanece poco a poco. Ramp up down : Aumenta gradualmente y disminuye. Random flash: La luz parpadea de forma aleatoria con velocidad e intensidad variable. Múltiples unidades parpadean de forma independiente uno de otro. Lightining: Los flashes simulan relámpagos. La duración no es ajustable. Spikes: Permanete iluminada tenuemente entre destellos. Ajuste la intensidad del flash, la duración y tipo. EFECTO BLINDER El efecto cegadora, en el que la luz permanece encendida durante un período prolongado, se encuentra disponible en todos los modos de DMX. En los modos de 3 y 4 canales, siempre que la combinación de la duración del flash y la velocidad eviten pausas entre destellos. Por ejemplo, el efecto cegador se puede lograr con una duración de flash de 0,25 segundos ( 250 ms) y una velocidad de destello de 4 destellos por segundo, o una duración del destello de 0,05 segundos ( 50 ms) y una velocidad de 20 destellos por segundo. En el modo de 3 y 4 canales DMX la intensidad del efecto cegador es controlable en el canal 1, la lámpara es regulada electrónicamente para evitar que se sobrecaliente.. La intensidad disminuye a medida que la energía se reduce. ES 12
14 FLASH Para lanzar un destello, comience con la intensidad y la velocidad de destello a 0 y luego establezca una intensidad en el canal 1. AUTÓNOMO Para su ejecución 1.- Encienda el aparato 2.- Configure el Pin 1 del DIP switch en ON. Establezca los pins 2-5 en OFF. Sitúe el pin 6 en ON para el funcionamiento a baja potencia o en OFF para alta potencia. 3.- Seleccione una velocidad de destello o el efecto cegadora. Establezca una velocidad de destello indicando un valor de 1 a 255 con los pines del 1 al 8 del DIP switch. El valor requerido para lograr una tasa de flash deseado se puede calcular de la siguiente manera. DIP value = x AC frequency Flash rate 4.- Ajuste el Pin10 del DIP switch en OFF para desactivar el modo autónomo, o en ON para un funcionamiento normal. ES 13
15 DMX PROTOCOLS MODO 1 CANAL DMX Canal Valor Porcentaje Función Blackout Velocidad flash,lenta o rápida Continuous Blinder effect MODO 3 y 4 CANALES DMX Valor Porcentaje Función Canal Intensidad del flash Blackout Mínimo a máximo Canal Duración del flash 0-650ms 50Hz AC 0-530ms 60Hz AC Canal Velocidad del flash Sin Flash Hz 50Hz AC Hz 60Hz AC Note: Habilitar el canal 4 con el interruptor de modo DIP nº4 en ON Canal 4 Valor Porcentaje Efectos Sin efecto Ramp up Ramp down Ramp up-down Random Lightning Spikes ES 14
16
Apliques A BL
Apliques A06 23 30 BL 45 Apliques A06 23 30 BL Apliques A06 14 30 Ne, A06 23 30 BL 48 LUMIK. IP40 Rectangular y estilizada. Gracias a su delicada luz esta luminaria de diseño sobrio envuelve los espacios
More informationProyectores P NE
Proyectores P05 01 36 NE 91 Proyectores P05 01 36 NE 92 LUMIK. IP20 Base circular y cuerpo tubular. Este proyector montado en superficie es compacto y potente, a la vez que discreto y de líneas limpias.
More informationTR21, TR22, TR23, and TR24 Wall Modules
TR21, TR22, TR23, and TR24 Wall Modules FEATURES SPECIFICATION DATA The TR21, TR22, TR23, and TR24 family of wall modules include: Models with setpoint adjustment. Models with occupied/unoccupied override
More informationXENO WET CEILING FAN MODEL #FP6729** Español p. 16 ATTACH YOUR RECEIPT HERE READ AND SAVE THESE INSTRUCTIONS. Purchase Date
XENO WET CEILING FAN MODEL #FP6729** Español p. 16 ATTACH YOUR RECEIPT HERE READ AND SAVE THESE INSTRUCTIONS Purchase Date Net Weight 23.81. lbs (10.8 kgs) Questions, problems, missing parts? Before returning
More informationProfessional Fog machine with RGBA effect USER MANUAL / MANUAL DE USUARIO
STEAM RGBA Professional Fog machine with RGBA effect 700 USER MANUAL / MANUAL DE USUARIO PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR P. 1 - Neo Steam
More informationALP-XP850 XPEDITION 850
ALP-XP850 XPEDITION 850 USER MANUAL Introduction Thank you for purchasing our ALP-XP850 Xpedition. We are confident that the Altec Lansing family of products will make your life easier by using the latest
More informationAWNING CONTROL KIT 98GCK-33B
AWNING CONTROL KIT 98GCK-33B REV.07282015 RV AWNING PRODUCTS 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500 www.girardrv.com AC MOTOR CONTROL MODULE GC274B INSTALLATION and
More informationQK-CE220RL V02 230V. CONTROL BOARD FOR A 230V ac SINGLE-PHASE MOTOR PLUG & PLAY. 433,92 MHz
user manual QK-CE220RL V02 CONTROL BOARD FOR A 230V ac SINGLE-PHASE MOTOR 230V 433,92 MHz PLUG & PLAY CONTENTS INTRODUCTION MAIN FEATURES OF THE CONTROL BOARD TECHNICAL DATA INSTALLATION LAYOUT AND CONNECTIONS
More informationENGLISH. Lighting Controls
PAGE REFERENCE GUIDE Lighting Controls This manual applies to the following products: Wireless Transmitters (Indoor / Outdoor) 180 Motion Sensor 240 Motion Sensor Entry Switch Receivers Wall Switch Receiver
More informationCurso sobre el Programa de intercambio de datos de inspecciones de seguridad en rampa (IDISR)
Curso sobre el Programa de intercambio de datos de inspecciones de seguridad en rampa (IDISR) Módulo 5 Descripción de los ítems que son evaluados en las inspecciones en rampa (Parte II) 12 al 16 de septiembre
More informationMiddle Panel Panneau du milieu Panel medio 1
A Desktop Dessus de bureau Tapa del escritorio B Left Panel Panneau gauche Costado izquierdo C Middle Panel Panneau du milieu Panel medio D Right Panel Panneau droit Costado derecho E Back Panel Panneau
More information500 Watt Quartz Flood Light on Telescoping Tripod - Extends 3.5' to 10'
500 Watt Quartz Flood Light on Telescoping Tripod - Extends 3.5' to 10' Part #: WALTP-Q500 The WALTP-Q500 500 Watt Quartz light tower extends from 3.5' to 10' and provides high intensity output and telescoping
More informationOwner s Manual. Tripp Lite DC-to-AC Inverters. Models: PINV2000, PINV2000HS, PINV3000 (AG-87A0) (AG-87A1) (AG-87A2) Español 25 Français 49
Owner s Manual Tripp Lite DC-to-AC Inverters Models: PINV2000, PINV2000HS, PINV3000 (AG-87A0) (AG-87A1) (AG-87A2) Español 25 Français 49 PROTECT YOUR INVESTMENT! Register your product for quicker service
More informationAbsorbentes solo aceites
Absorbentes solo aceites SOLO ACEITES e hidrocarburos, rechaza el agua, por lo que está especialmente indicado para aplicaciones en acuíferos, puertos y lugares donde, en presencia de agua, se requiera
More informationInstallation Instructions Free-Standing and Front Control Electric Ranges
Installation Instructions Free-Standing and Front Control Electric Ranges BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT Save these instructions for local inspector s use.
More informationPARTE COMÚN LENGUA EXTRANJERA INGLÉS
DIRECCIÓN GENERAL DE POLÍTICAS EDUCATIVAS Y ORDENCIÓN ACADÉMICA PRUEBA DE ACCESO A CICLOS FORMATIVOS DE GRADO SUPERIOR DE LA FORMACIÓN PROFESIONAL ESPECÍFICA 18 de junio de 2009 Centro donde se realiza
More informationOperator's Manual. Model: RY10MK-PRO MPN: RA-MLT Gallon Direct Fire Melter Kettle Burner Model with Adjustable Flame-Out Valve
Operator's Manual Model: RY10MK-PRO MPN: RA-MLT-0009 10 Gallon Direct Fire Melter Kettle Burner Model with Adjustable Flame-Out Valve U.S. Patent No. 9,739,021 For Technical Support Please Visit www.rynoworx.com
More informationUser Guide English (2 13) Guía del usuario Español (14 25) Guide d utilisation Français (26 37) Guida per l uso Italiano (38 49)
User Guide English (2 13) Guía del usuario Español (14 25) Guide d utilisation Français (26 37) Guida per l uso Italiano (38 49) Benutzerhandbuch Deutsch (50 61) Appendix English (62) User Guide (English)
More informationGavita Pro 1650 e LED ML
Pro line Gavita Pro 1650 e LED ML 1 Introduction Thank you for purchasing the Gavita Pro 1650 e LED ML. This manual describes the mounting and installing of the product and also describes how to use the
More informationEXPLOSIONADO DE PARTES
EXPLOSIONADO DE PARTES REFRIGERADOR DUPLEX Modelo: CABINET PARTS Mexico S.A de C.V. 1/25 CCR R e f Descripción CABINET PARTS C a n t Numero de Parte 2 Front Roller (2) 1 4386774 3 Screw (2) 1 3400517 4
More informationBlue Series Hot Melt Hose with RediFlext II Hanger System
Instruction Sheet P/N 1124594_01 Blue Series Hot Melt Hose with RediFlext II Hanger System Safety WARNING! Allow only personnel with appropriate training and experience to operate or service the equipment.
More informationCOMMUNITY CONVERSATION: POLICE SERVICES AND LEADERSHIP
COMMUNITY CONVERSATION: POLICE SERVICES AND LEADERSHIP BACKGROUND The City of Burien is searching for a permanent Police Chief to lead the Department. This change in leadership provides an opportunity
More informationMODEL MULTI-BRAND REMOTE CONTROL
MODEL 57999 MULTI-BRAND REMOTE CONTROL This remote control can be programmed to activate up to two products, such as a garage door opener, gate operator, or commercial door operator. Each button on the
More informationITEM # KEYPORT HUGGER CEILING FAN MODEL #40141
ITEM #0403520 KEYPORT HUGGER CEILING FAN MODEL #40141 Harbor Breeze is a registered trademark of LF, LLC. All Rights Reserved. Español p. 21 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions,
More information36-INCH FREE- STANDING GAS RANGE. Model No. PLGF659E F50S2
" Product No. 30857636F50S2 Series 36" f/s gas Color stainless Market North America Wiring Diagram 318045813 Owner's Guide 318200763 Installation Instructions 318201760 Service Data Sheet 318127026 Timer
More informationLogistic information for CeDInt visitors: How to get to CeDInt.
Logistic information for CeDInt visitors: How to get to CeDInt. CeDInt is located in Campus de Montegancedo, 14 Km from the center of Madrid, in a specially protected natural environment. If you drive
More informationCompact Stainless Spit Roast
Compact Stainless Spit Roast Instructions As soon as you get the machine to your destination please start it up and make sure it works following the Instructions below. This is just in case something has
More informationREAD AND SAVE THESE INSTRUCTIONS
MODEL 114 KICKSPACE HEATER Factory Wired 240/208 V.A.C. Page 1 READ AND SAVE THESE INSTRUCTIONS WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
More informationVitAir Turbo SMART VitAir Turbo S. US (Wifi) US US US
VitAir Turbo SMART VitAir Turbo S US-10032732 (Wifi) US-10032746 US-10032747 US-10032748 Ich bin ein Berliner* * John F. Kennedy on June 26, 1963 in his speech in Berlin, on the occasion of the 15th anniversary
More informationharborbreezeoutlet.com
Harbor Breeze is a registered trademark of LF, LLC. All Rights Reserved. ITEM #0096879 0096950 0096982 0205233 SOS ITEM #0018035 BELLEVUE CEILING FAN Federal regulations require ceiling fans with light
More informationFAMILY INDEPENDENCE ADMINISTRATION Seth W. Diamond, Executive Deputy Commissioner
FAMILY INDEPENDENCE ADMINISTRATION Seth W. Diamond, Executive Deputy Commissioner ` James K. Whelan, Deputy Commissioner Policy, Procedures and Training Lisa C. Fitzpatrick, Assistant Deputy Commissioner
More informationInstallation Instructions Electric Slide-In Ranges
Installation Instructions Electric Slide-In Ranges 2 PREPARE THE OPENING (FOR INDOOR USE ONLY) See illustrations for all rough-in and spacing dimensions. The range may be placed with 0 clearance (flush)
More informationOWNER S MANUAL READ BEFORE USE!
OWNER S MANUAL READ BEFORE USE! Model No.: HYFP50095-92 Item No.: BH1609209919 WARNING: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
More informationGlammbox Crea7ion.E. GlammFire. Crea7ion by GlammFire. GlammFire
Crea7ion by Wall Mounted Fireplaces// Glammbox 420 Glammbox 420 DF Glammbox 450 Glammbox 450 DF Glammbox 770 Glammbox 770 DF Glammbox 1150 Glammbox 1150 DF Glammbox 1600 Glammbox 1600 DF Glammbox 2150
More informationCineMate 15/10. home theater system. Owner's Guide Guía del usuario Notice d utilisation Guia dos propriet rios
CineMate 15/10 home theater system Owner's Guide Guía del usuario Notice d utilisation Guia dos propriet rios Important Safety Information Please read this owner s guide carefully and save it for future
More information2 PREPARE THE OPENING (FOR INDOOR USE ONLY)
Installation Instructions Free-Standing and Front Control Electric Ranges Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.geappliances.com In Canada, call 1.800.561.3344 or visit www.geappliances.ca
More informationAMPLIFICADOR PARA MÁSTIL AMPLIFIER FOR MAST AMPLIFICATEUR POUR MÂT CÓDIGOCODECODE MODELOMODELMODELE 900 AM AM AM07 Número de entradas
AMPLIFICADORES PARA MÁSTIL Y ALIMENTADORES AMPLIFIERS FOR MAST AND POWER SUPPLIES AMPLIFICATEURS POUR MÂT ET ALIMENTATIONS SERIE 903 SERIES AMPLIFICADOR PARA MÁSTIL AMPLIFIER FOR MAST AMPLIFICATEUR POUR
More informationUltramodern remote control technology for your patio comfort. Comfortable WeiTronic remote control.
Comfortable WeiTronic remote control Ultramodern remote control technology for your patio comfort The WeiTronic operating comfort allows you to control your weinor accessories with ease through practical
More informationINS #Shaper IL525013N WARNING WARNING WARNING WARNING WARNING
IL525013N INS #Shaper Make Certain Power is OFF before starting installation or attempting any maintenance. Risk of Fire/Electric Shock. If not qualified, consult an electrician. Risk of Electric Shock
More informationUSER MANUAL / MANUAL DE USUARIO
STEAM Faze machine F1400 USER MANUAL / MANUAL DE USUARIO PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR P. 1 - Neo Steam F1400 1. OVERVIEW Steam F1400 Professional
More informationINSERT HOODS INSTALLATION INSTRUCTIONS..9. Write the model and serial numbers here: Model # Serial #
Custom INSERT HOODS SAFETY INFORMATION...3 USING THE HOOD Controls....5 Chef Connect....6 CARE AND CLEANING Filters....7 Surfaces....8 Lights....8 INSTALLATION INSTRUCTIONS..9 TROUBLESHOOTING TIPS....
More informationUSER MANUAL. Tavor 8-T Active Ceiling Speaker MODEL: P/N: Rev 4
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: Tavor 8-T Active Ceiling Speaker P/N: 2900-300343 Rev 4 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions
More informationITEM # , , ARMORY CEILING FAN MODEL #40087, 40088, 40090
ITEM #0451801, 0451802, 0451803 ARMORY CEILING FAN MODEL #40087, 40088, 40090 Harbor Breeze is a registered trademark of LF, LLC. All Rights Reserved. Español p. 23 ATTACH YOUR RECEIPT HERE Serial Number
More informationWE5910S01. 30" Acero Inoxidable. Capacidad Color. Especificaciónes. Whirlpool Mexico S.A de C.V. 1/13 JAS
Especificaciónes Whirlpool Mexico S.A de C.V. 1/13 JAS Cubierta, Quemadores, Parrillas, Panel s Whirlpool Mexico S.A de C.V. 2/13 JAS Descripción Cubierta, Quemadores, Parrillas, Panel s C a Numero de
More informationThe Ventana Ceiling Fan
The Ventana Ceiling Fan Net Weight 11.1 kg. (24.48 lbs.) Model No. FP8032DZ OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS Important Safety Instructions WARNING: To avoid fire, shock and serious personal
More informationharborbreezeoutlet.com
Harbor Breeze is a registered trademark of LF, LLC. All Rights Reserved. Federal regulations require ceiling fans with light kits manufactured or imported after January 1, 2009, to limit total wattage
More informationBELLHAVEN II CEILING FAN
ITEM #18039 BELLHAVEN II CEILING FAN MODEL #E-BLHII52VPW5C4S Harbor Breeze is a registered trademark of LF, LLC. All Rights Reserved. español p. 20 Federal regulations require ceiling fans with light kits
More information212iLM Mullion (ILLUMINATED WEATHER RESISTANT) Keypad
International Electronics, Inc. 427 Turnpike Street Canton, Massachusetts 02021 212iLM Mullion (ILLUMINATED WEATHER RESISTANT) Keypad Stand Alone Keypad-Installation Manual Features: 120 User Capability
More informationC VOLT LITHIUM-ION BATTERY CHARGER
Operator s Manual C3 19.2 VOLT LITHIUM-ION BATTERY CHARGER Model No. 5335 No. 5336 ѥ ѥwarning: To reduce the risk of injury, the user must read and understand the Operator s Manual before using this product.
More informationINSTALLER AND OWNER GUIDE
5118237/01 Model 0581901 Chester Log Effect Electric Stove This guide is intended to help you install and care for your Baxi Fires Division electric stove. Please read carefully before installing and using
More informationProduct Guide LED OBSTRUCTION LIGHTS
Product Guide LED OBSTRUCTION LIGHTS Certified to: FAA AC NO: 150/5345-43F FAA Engineering Brief No. 67 Compliant to: ICAO Annex 14, 4th Edition, July 2004 ICAO Aerodromes Design Manual, Chapter 18 Canadian
More informationRMC1E - Variable Flame Height EASY Control
Owner s Manual RMC1E - Variable Flame Height EASY Control General Assembly, Installation, and Operation Instructions for use with Natural Gas Burners; F, FX, CS, CXF, TNA or Propane Gas Burners: FA, FAX,
More informationr e - p a r t s. c o m
Owner s Manual SPK3E - Manual EASY Control General Assembly, Installation, and Operation Instructions for use with Natural Gas Burners; F, FX, CS, CXF, TNA or Propane Gas Burners: FA, FAX, CA, CXFA, TNA/LP
More informationMotorized Cassette Awning E6100. Instruction ROHS
Motorized Cassette Awning E6100 Instruction ROHS 1 Installation Instruction for E6100 Cassette Awning I. Installation Steps of E6100 Cassette Awning.2 II. Installation Guide of DLC-B Controlling board
More informationSPK3E - Manual EASY Control
SPK3E - Manual EASY Control General Assembly, Installation, and Operation Instructions for use with Natural Gas Burners; F, FX, CS, CXF, TNA or Propane Gas Burners: FA, FAX, CA, CXFA, TNA/LP LISTED BY
More informationMinibar User Manual MBA 4000 W
Minibar User Manual MBA 4000 W Read this manual prior to initial operation of the product! Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through
More informationThe Torto. Ceiling Fan. Model No. FP7902BN READ AND SAVE THESE INSTRUCTIONS. Net Weight kg (27.4 lbs)
The Torto Ceiling Fan Net Weight 12.46 kg (27.4 lbs) Model No. FP7902BN OWNER S MANUAL READ AND SAVE THESE INSTRUCTIONS Important Safety Instructions WARNING: To avoid fire, shock and serious personal
More informationL-864 L-865 / L-864 L-810 L-810. Vigilant Series LED Based Obstruction Lights
L-864 L-865 / L-864 L-810 L-810 Vigilant Series LED Based Obstruction Lights Certified to: FAA AC NO: 150/5345-43F FAA Engineering Brief No. 67 Compliant to: ICAO Annex 14, 4th Edition, July 2004 ICAO
More informationREAD AND SAVE THESE INSTRUCTIONS
DECORATIVE SERIES CEILING VENTILATOR MODELS 754RB 754SN Page 1 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OB- SERVE THE FOLLOWING: 1. Use
More informationquick and easy installation guide
www.directdriveopener.com quick and easy installation guide Back 2 Front. Motor Carriage 2. C-rail. Chain. Limit stops. Slide in part (tensioner) Rail assembly Insert C-rail parts () into the connecting
More informationharborbreezeoutlet.com
ITEM #18037 18038 Harbor Breeze is a registered trademark of LF, LLC. All Rights Reserved. CHESHIRE II CEILING FAN MODEL #CSD52FBZ5C4S CSD52BNK5C4S español p. 17 E124404 Questions, problems, missing parts?
More informationQUICK START GUIDE: FIERY PROSERVER FOR EFI CRETAPRINT PRINTERS
QUICK START GUIDE: FIERY PROSERVER FOR EFI CRETAPRINT PRINTERS This document is a step-by-step guide on how to set up and use the Fiery proserver with your Cretaprint printer. Table of Contents Connecting
More informationINSTALLATION INSTRUCTIONS INSTRUCCIONES DE INSTALACIÓN. SMART-LIFT Electric Ceiling Lift Elevador eléctrico de techo SMART-LIFT
INSTALLATION INSTRUCTIONS INSTRUCCIONES DE INSTALACIÓN SMART-LIFT Electric Ceiling Lift Elevador eléctrico de techo SMART-LIFT This device complies with part 15 of the FCC rules. Operation is subject to
More informationPower Relay RCE. Ordering Information. A High-capacity, High-dielectric-strength Relay Compatible with Momentary Voltage Drops
Power Relay A High-capacity, High-dielectric-strength Relay Compatible with Momentary Voltage Drops No contact chattering for momentary voltage drops up to 0% of rated voltage. Wide-range AC-activated
More information12V MOTION SENSOR 98GC779G INSTALLATION & PROGRAMMING GUIDE REV RV AWNING PRODUCTS
12V MOTION SENSOR 98GC779G INSTALLATION & PROGRAMMING GUIDE REV.07242015 RV AWNING PRODUCTS 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500 www.girardrv.com Girard Systems
More informationTCWS54 SEE THRU DIAMOND BURNER INSTALLATION KIT INSTRUCTIONS
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationGLM300 Semi-auto Slicer
Frequency: Before each days use Division: Location: User: Supervisor: Preceda Code: Article Number:
More information1/2 INCH BRUSHLESS HAMMER DRILL MODEL #KHD 524B-03 ITEM # / / Español p. 19 ATTACH YOUR RECEIPT HERE
ITEM #0790020/ 0790021/0790022 1/2 INCH BRUSHLESS HAMMER DRILL MODEL #KHD 524B-03 KOBALT and the K Design are registered trademarks of LF, LLC. All Rights Reserved. Español p. 19 ATTACH YOUR RECEIPT HERE
More informationRANGE HOOD READ AND SAVE THESE INSTRUCTIONS
ALLURE QS SERIES ALLURE QS SERIES READ AND SAVE THESE INSTRUCTIONS! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner
More informationINSTRUCTIONS INSTALLATION UNIVERSAL SERIES PATIO AWNING HARDWARE , , ,
RECORD THIS INFORMATION FOR FUTURE REFERENCE: Model Number Serial Number Hardware Model Number Hardware Serial Number Date Purchased Retailer / Qualified Installer INSTALLATION INSTRUCTIONS UNIVERSAL SERIES
More informationFAN / LIGHT / NIGHT LIGHT COMBINATION VENTILATOR READ AND SAVE THESE INSTRUCTIONS WARNING CAUTION PLANNING DUCTWORK AND WIRING FOR BEST RESULTS
MODEL 750 FAN / LIGHT / NIGHT LIGHT COMBINATION VENTILATOR Page 1 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN- JURY TO PERSONS, OBSERVE THE FOLLOWING: 1.
More informationEnigma. Ceiling Fan. Net Weight 38 lbs. or 17.3 kg. Model No. FP2120** Series OWNER S MANUAL READ AND SAVE THESE INSTRUCTIONS
Enigma Ceiling Fan Suitable for use with Solid State Speed Controls WARNING: Support Directly From Building Structure Net Weight 38 lbs. or 17.3 kg. Model No. FP2120** Series OWNER S MANUAL READ AND SAVE
More informationModel 750X. Model 500X 500X & 750X. User s Guide Guía del Usuario Mode d emploi
Model 750X Model 500X 500X & 750X User s Guide Guía del Usuario Mode d emploi Thank you...for purchasing a Drill Doctor. It is sure to become a valuable tool because you will always have sharp drill bits
More informationINSTRUCTION MANUAL ALEKO RETRACTABLE AWNING
INSTRUCTION MANUAL for ALEKO RETRACTABLE AWNING www.alekoproducts.com FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY! 1 Important Safety Precautions WARNING NOTE: FOR PERSONAL SAFETY,
More informationEXPLOSIONADO DE PARTES
EXPLOSIONADO DE PARTES LAVADORA FRONTAL Modelo: Marca TOP AND CABINET PARTS Mexico S.A de C.V. 1/12 CJG R e f Marca Descripción TOP AND CABINET PARTS C a n t Numero de Parte 2 Top 1 8540716 3 Cabinet 1
More informationCordless Impact Driver Atornillador de Impacto Inalámbrico
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Impact Driver Atornillador de Impacto Inalámbrico XDT IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar. ENGLISH (Original instructions) SPECIFICATIONS
More informationGeneral-Use Auto-Tuning HPX-T Series
General-Use Auto-Tuning HPX-T Series Built-in Hyper-tuning automatically adjusts scanning characteristics. Adjustment steps, results and scanning conditions are digitally displayed by LED. Digital display
More informationPARTS CATALOG LISTA DE PIEZAS
Fits the following models: Se adapta a los siguientes modelos: SRM-ALL Models PARTS CATALOG LISTA DE PIEZAS 20mm Blade Conversion Kit 20mm Kit Conversión a Cuchilla 15 m 50 ft ECHO, INCORPORATED 400 Oakwood
More informationZONIX WET CUSTOM CEILING FAN
ZONIX WET CUSTOM CEILING FAN MODEL #MA4660** MODEL #MA4660SSBNW Español p. 25 ATTACH YOUR RECEIPT HERE AND REGISTER YOUR FAN AT FANIMATION.COM READ AND SAVE THESE INSTRUCTIONS Serial Number Purchase Date
More informationRegister your product and get support at CEM1000. User manual. Manual del usuario. Manual do Usuário ZH-TW ZH-CN
Register your product and get support at www.philips.com/welcome CEM1000 EN PT-BR User manual Manual del usuario Manual do Usuário ZH-TW ZH-CN Contenido Reproducción de la introducción 19 Conexión de una
More informationOwner s Manual. Tripp Lite DC-to-AC Inverter. Model: PINV1500 (Series Number: AG-879F) Español 22 Français 43
Owner s Manual Tripp Lite DC-to-AC Inverter Model: PINV1500 (Series Number: AG-879F) Español 22 Français 43 PROTECT YOUR INVESTMENT! Register your product for quicker service and ultimate peace of mind.
More informationOWNER S MANUAL Swash CL950 Advanced Bidet Toilet Seats
OWNER S MANUAL Swash CL950 Advanced Bidet Toilet Seats CL950-EW CL950-RW CL950-EW ITM./ART. 1244669 CL950-RW ITM./ART. 1244670 Attach Proof of Purchase to This Page Adjunte prueba de compra a esta Página
More informationNatural Himalayan Salt Lamp
Model: Elora Natural Himalayan Salt Lamp Questions or Concerns? Please contact us Monday - Friday 9:00am - 5:00pm PST at (888) 726-8520 or email support@levoit.com Thank You. Thank you for purchasing your
More informationDEWALT
If you have questions or comments, contact us. Pour toute question ou tout commentaire, nous contacter. Si tiene dudas o comentarios, contáctenos. 1-800-4-DEWALT www.dewalt.com INSTRUCTION MANUAL GUIDE
More informationFire's Edge Fire Pit/Fire Pit Inserts For (Automated) Model 100-A
Fire's Edge Fire Pit/Fire Pit Inserts For (Automated) Model 100-A OWNER S MANUAL / OPERATING AND MAINTENANCE INSTRUCTIONS For your safety: If you smell gas: 1. Shut off gas to the appliance 2. Extinguish
More informationIntroduction 2. Other Applicable Documents 2. Scope of Delivery 3. Attaching the Snap-on Ferrite Suppressor 4
H-206.F2 6-Axis Precision Alignment System Contents Introduction 2 Other Applicable Documents 2 Scope of Delivery 3 Attaching the Snap-on Ferrite Suppressor 4 Connecting the Hexapod to the C-887 with the
More informationPRBP675i. EN Operator's manual 2-13
PRBP675i EN Operator's manual 2-13 ES-MX FR-CA Manual del usuario Manuel d utilisation 14-26 27-39 BBP58VPR Contents INTRODUCTION... 2 SAFETY...4 ASSEMBLY... 8 MAINTENANCE...11 TROUBLESHOOTING...11 TECHNICAL
More informationAFC-50 Automatic French Fry Cutter Instruction Manual
AFC-50 Automatic French Fry Cutter Instruction Manual Fry Factory Inc. 67 Watts Ave, Charlottetown, PEI, C1E 2B7, Canada Phone: 902-368-2900 Fax: 902-368-8645 Email: info@fryfactoryinc.com Website: www.fryfactoryinc.com
More informationURBANIA CEILING FAN ITEM # MODEL #E-AR54BNK5C1. Español p. 21 ATTACH YOUR RECEIPT HERE. Serial Number. Purchase Date
ITEM #0151279 URBANIA CEILING FAN Harbor Breeze is a registered trademark of LF, LLC. All Rights Reserved. MODEL #E-AR54BNK5C1 Español p. 21 Federal regulations require ceiling fans with light kits manufactured
More informationUSERS MANUAL RS6110 RS6220 RS Features
RS6110 RS6220 RS6 3 20 352-00057-001 Rev B USERS MANUAL Thank you for purchasing a Robertshaw RS6000 programmable thermostat. This user s manual will guide you through the setup of the RS6110 single stage,
More informationEngineering Design Assurance Test Report ( S )
TEST EQUIPMENT LIST: AC Source : Chroma programmable AC source Model 61504 Power Analyzer : Chroma Power Analyzer Model 6630 Load : Chroma Electronic DC Load 63103 Oscilloscope : Lecroy wave surfer 424
More informationProduct instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E
Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E The Trimfast Ream Cutters are reliable, high performance cutters that will give you the results you need quickly
More informationOREON GROW LIGHT 2.2
OREON GROW LIGHT 2.2 (GL 600 2.2 XXX) INSTALLATION MANUAL Version: 20180830US/CA IMPORTANT: READ CAREFULLY BEFORE STARTING INSTALLING THE FIXTURE. KEEP FOR FUTURE REFERENCE. MANUAL FOR INSTALLER Thank
More informationPARTS LIST CHARGER 2022 ABLT
PARTS LIST CHARGER 2022 ABLT HEAD ASSEMBLY ITEM PART NO. DESCRIPTION QTY 101 5990731 SPRING CLIP PAD HOLDER SET INCLUDES: 1 101A 9120205 #8 X 1/2 PAN HEAD PHILLIPS SHEET METAL SCREW PACK OF 3 3 102 9121490
More informationPYRAMID CEILING FAN MODEL #LP8406** Español p. 21 ATTACH YOUR RECEIPT HERE READ AND SAVE THESE INSTRUCTIONS
PYRAMID CEILING FAN MODEL #LP8406** Español p. 21 ATTACH YOUR RECEIPT HERE READ AND SAVE THESE INSTRUCTIONS Serial Number Purchase Date Net Weight 17.40 lbs (7.89 kg) Questions, problems, missing parts?
More informationToyostove Error Code EE 2 (EE 6)
Toyostove Error Code EE 2 (EE 6) WARNING Rural Energy Enterprises, Inc. does not accept liability for the improper use of this information. Installation, service, and maintenance of heating equipment should
More informationMX Series MX40-7XXX Series MX40-6XXX Series. Selection Guide. Applications. DuraDrive Series Actuator (Includes Accessories)
MX40-6043 Series MX40-7XXX Series MX40-6XXX Series Selection Guide Applications DuraDrive Direct Coupled Actuators are designed to accept two-position, floating, or proportional control from a DDC system
More informationModel Crosspoint Matrix
Model 3000 4380 256 Crosspoint Matrix 90401270 Page 1 All technical data and specifications in this publication are subject to change without prior notice and do not represent a commitment on the part
More informationUser Manual. 1000W Stackable 1.2 Cu. Ft. Commercial Microwave. Model: 180MW112T 05/2017. Please read and keep these instructions. Indoor use only.
1000W Stackable 1.2 Cu. Ft. Commercial Microwave Model: 180MW112T 05/2017 Please read and keep these instructions. Indoor use only. IMPORTANT SAFETY INSTRUCTIONS When using electrical equipment, basic
More informationINSTRUCTIONS MANUAL CAST IRON STOVE
INSTRUCTIONS MANUAL CAST IRON STOVE CA-SGB06 Warning: Use outdoors only Read the instructions before using the appliance and retain for future reference. 1 These instructions give some important information
More information