NATURAL GAS CONVERSION KIT

Transcription

1 Model #: / G NATURAL GAS CONVERSION KIT ONLY Compatible with barbecues that bear this SYMBOL:

2 FOR YOUR SAFETY CAUTION: Read and follow all safety statements, assembly instructions, and use and care directions before attempting to assemble and cook. WARNING: The information in these instructions must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death. INSTALLER/ASSEMBLER: Leave this manual with consumer. INSTALLATION SAFETY PRECAUTIONS Not for use with LP gas. This kit converts your grill for natural gas use at 7 inch water column supply pressure. Verify supply pressure with your local gas company. If supply pressure is different than 7 inch, contact a certified gas fitter for assistance. Grill installation must conform with local codes, or in their absence with National Fuel Gas Code, NFPA 54 / ANSI Z National Electrical Code, ANSI / NFPA 70. Grill is not for use in or on recreational vehicles and/or boats. 2

3 TABLE OF CONTENTS For Your Safety...2 Installation Safety Precautions...2 Parts List... 4 Before You Begin...5 Assembly Instructions Notes If you have questions or need assistance during conversion, visit us online at 3

4 PARTS LIST A B C D ITEM # QUANTITY DESCRIPTION PART NO. A 1 5/8 quick connect socket G B 1 10 ft. natural gas hose G C 1 Orifice removal tool G T-9000 D 1 Valve screwdriver G U-9000 Additional tools required (not included in kit): Adjustable wrench or #17 wrench and #19 wrench 4

5 BEFORE YOU BEGIN 1. All control knobs must be in the OFF position. 2. Ensure that the propane tank is closed. 3. Disconnect the BBQ regulator from the propane tank. OFF Estimated time to convert to NG: minutes ATTENTION: FOR COLEMAN REVOLUTION Dual Fuel (G53701 / ) Models The charcoal ignition burner valve works with both LP and NG gas. It is only necessary to convert GAS SIDE of the barbecue. 5

6 1 MAIN BURNER CONVERSION Open lid, remove and set aside the warming rack, all cooking grates, and all heat plates. Warming Rack Cooking Grates Heat Plates 6

7 2 A Remove the hitch pins from the burners and carryover tubes. Hitch pins Hitch pins Carryover Burners NOTE: Depending on your BBQ configuration your burners and carryovers may be slightly different. 7

8 2 B Remove burners. If one or more burners has an electrode attached, remove this burner from valve and lay in burner box. NOTE: Depending on your BBQ configuration your burners and carryovers may be slightly different. 8

9 2 ATTENTION: FOR COLEMAN REVOLUTION Dual Fuel (G53701 / ) Models The charcoal ignition burner valve works with both LP and NG gas. It is only necessary to convert GAS SIDE of the barbecue. 9

10 3 Insert the orifice removal tool into the burner box opening to locate the valve orifice. Once the tool is positioned correctly on the orifice, turn the orifice removal tool counter clockwise to remove the LP orifice. Repeat this step for all main burners. Orifice Orifice Removal Tool Orifice Removal Tool 10

11 4 Remove all control knobs to access the valve switch plate. A 11

12 4 B Locate the switch screw circled in the diagram. Using the screwdriver supplied with this kit, turn the screw counter clockwise 3-5 full turns OR until it stops. WARNING: Do Not Use Power Tools. C 3-5X Switch screw Valve screwdriver 12

13 5 Re-assemble the control knobs. 13

14 6 Assemble main burners, one at a time, making sure the burner engages the valve. Main burners 14

15 7 Re-attach burners using hitch pins. Re-attach carryovers using hitch pins. Hitch pins Hitch pins Carryover Burners 15

16 8 Re-position heat plates, cooking grates and warming rack. Warming Rack Cooking Grates Heat Plates 16

17 9 SIDE BURNER CONVERSION If your barbecue does not have a side burner proceed to step 14. Lift the side burner lid. Remove the side burner cooking grate. 17

18 10 Detach the side burner eletrode. Remove the side burner, and side burner support clip (if applicable). Side burner 18

19 11 Using the orifice removal tool, remove the side burner valve orifice, as shown. Orifice Removal Tool Orifice Orifice Removal Tool 19

20 12 Remove the side burner knob to access the valve switch plate. A 20

21 12 B Locate the switch screw circled in the diagram. Using the screw driver supplied with this kit, turn the screw counter clockwise 3-5 full turns OR until it stops. Re-assemble the side burner knob. WARNING: Do Not Use Power Tools. C 3-5X Switch screw Valve screwdriver 21

22 13 Re-attach the side burner eletrode. Re-assemble the side burner, side burner support clip, and side burner grate. Side burner 22

23 14 FINAL STEP IN CONVERSION Use adjustable wrench to remove regulator. Propane regulator 23

24 15 Attach the natural gas hose, and wrench tighten. 2-Burner Barbecue Natural gas hose Coleman Dual Fuel 24

25 16 IMPORTANT! BEFORE USING GRILL READ SAFE USE & CARE MANUAL that came with your barbecue for important safety instructions. Please read Connecting Your Grill to the Natural Gas Source (p.6), Leak Test (p.5), and Burner Flame Check (p. 9 Coleman /p. 13 Master Chef ). ATTENTION! PERFORM LEAK TEST on all connections as specified on p. 5 of your barbecue s Safe Use and Care Manual. Leak checks should be performed on all new BBQs even if assembled by an assembler or gas technician. Leak checks should be performed frequently thereafter. 2-Burner Barbecue Coleman Dual Fuel 25

26 NOTES 26

27 NOTES 27

28 NATURAL GAS CONVERSION KIT 2017 Winners Products Engineering