SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 AL AMJAAD TIRE TESTING LABORATORY W. HOUSE NO. 145, PHASE-I, MADINATAL MUSTAUDAT AL-KHUMRA P.O. Box 2302, Jeddah KINGDOM OF SAUDI ARABIA Israel Mendoza Phone: 00966(2) LOC 24 MECHANICAL Valid To: May 31, 2018 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on tires, alloy rims, and tire tubes: Test Light Alloy Wheels Impact 13º ISO 7141; GSO/ISO 7141; SASO/ISO 7141 Light Truck and Bus Tires Visual Inspection (Markings and Labels) Breaking Energy Test/Strength Test (10 to 8000) kgf Load Rolling Resistance Test (10 to 150) kph SASO No. 1134, GSO 645, SASO No. 1136, GS 647, SASO No ISO 10454; SASO No GSO 645, SASO No. 1136, GS 647; SASO/ISO ISO 10454; SASO No. 1134, GSO 645, SASO No. 1136, GS 647; SASO/ISO ECE 117 Torque Method; SASO/GSO/ISO 28580, (Torque Method); SASO 2857 (A2LA Cert. No ) 05/31/2016 Page 1 of 4

2 Test Visual Inspection ECE 75 Strength Test High Speed Test (100 to 300) kph Speed ECE 75; Visual Inspection GSO 51, 52 & 53 ; ; SASO No Bead Unseating Test (6800 to 11350) N Breaking Energy Test Tread Elongation Test (300 % minimum) Tread Tensile Strength Test (1.2 kg/mm 2 minimum) Aging Test (70 ºC Oven Temperature at 80% Strength) High Speed Test (100 to 300) kph Speed SASO/ SASO/ SASO 445,447 & 448 SASO 445,447 & 448 SASO/ (A2LA Cert. No ) 05/31/2016 Page 2 of 4

3 Test Temperature Resistance Test (10 to 200) kph Rolling Resistance Test (10 to 150) kph Re-Treaded Light Truck and Bus Tires Visual Inspection (Markings and Labels) Performance Test (10 to 8000) kgf Load SASO/ GSO 1784; SASO 2253 ECE 117 Torque Method; SASO/GSO/ISO 28580, (Torque Method); SASO 2857 GSO 962; SASO 1275 GSO 962; SASO 1275 Tire Inner Tubes Tensile Strength JIS D 4231 Elongation JIS D 4231 Aging JIS D 4231 Permanent Elongation JIS D 4231 (A2LA Cert. No ) 05/31/2016 Page 3 of 4

4 I. Dimensional Testing 1 Parameter Range CMC 2 (±) Technique / Method Width 3 Light Truck & Bus Tires Re-Treaded Light Truck & Bus Tires 0.3 mm Caliper / Caliper / SASO No GSO 645, SASO No. 1136, GS 647 Caliper / GSO 962; SASO 1275 Caliper / ECE 75 Diameter 3 Light Truck & Bus Tires Re-Treaded Light Truck & Bus Tires Up to mm Up to mm Up to mm Up to 1000 mm 1 mm Measuring Tape / Measuring Tape / SASO No GSO 645; SASO No. 1136, GS 647 Measuring Tape / GSO 962; SASO 1275 Measuring Tape / ECE 75 1 This laboratory offers commercial dimensional testing service only. 2 Calibration and Measurement Capability (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine measurements of nearly ideal measurement standards or nearly ideal measuring equipment. Calibration and Measurement Capabilities represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific measurement performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific measurement. 3 This test is not equivalent to that of a calibration. (A2LA Cert. No ) 05/31/2016 Page 4 of 4

5 Accredited Laboratory A2LA has accredited AL AMJAAD TIRE TESTING LABORATORY KINGDOM OF SAUDI ARABIA for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 31 st day of May Senior Director of Quality and Communications For the Accreditation Council Certificate Number Valid to May 31, 2018 For the tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.