TOOLS for Liquid Plastics Glas-Fibre Reinforced Liquid Plastic Coating

Transcription

1 PPW-POLYPL AN-WERK ZEUGE GMBH CATALOGUE 2004 TOOLS for Liquid Plastics Glas-Fibre Reinforced Liquid Plastic Coating TOOL EQU IPMENT

2 PPW-POLYPL AN-WERK ZEUGE GMBH The articles in this catalogue are manufactured in german measurements. The mentioned inch + ft are just a special information for our customers. Subject to technical alterations 2

3 PPW-POLYPLAN-WERKZEUGE GMBH P.O. Box D Hamburg Phone: Fax: Internet: Home address: Riekbornweg 20 D Hamburg-Schnelsen 3

4 PPW-POLYPL AN-WERK ZEUGE GMBH (3107 N 3130 N) Roller hard-wearing design, solvent-resistant, rigid PE body, with internal tube, approx. 50 mm ~2 internal diameter, sleeve-like fur cover. Width 7 cm 12 cm 18 cm 25 cm 30 cm ~2 3 /4 4 3 /4 7 1 / Nylon fur 14 mm ~ 5 /8 pile tightly curled, superior material absorption, thus substantial high coating (3107 N) (3112 N) (3118 N) (3125 N) (3130 N) E 2.80 E 3.40 E 4.15 E 5.35 E 8.70 (3107 P 3125 P) Perlon fur 18 mm ~ 3 /4 pile, twisted, ends roughened, superior material absorption, appropriate high coating (3107 P) (3112 P) (3118 P) (3125 P) E 3.70 E 4.90 E 6.10 E 7.90 solvent-resistant,, rigid body of extra hard synthetic material, with internal tube approx. 50 mm ~2 internal diameter, spirally glued fur Width 25 cm ~10 Perlon fur 12 mm ~ 1 /2 pile woven, black stripes for non-fuzzy coatings (3125 PK) E 7.90 (3125 PK) Perlon fur 8 mm ~ 5 /16 pile woven, black and yellow stripes for thin coating, absolutely non-fuzzy (3125 PG) E 7.90 (3125 PG) Mohair plush 4 mm ~ 3 /16 pile woven, goat hair (no plastics) for very thin coatings, to remove air bubbles Width 7 cm 12 cm 18 cm 25 cm ~2 3 /4 4 3 /4 7 1 /8 10 (3607 MH 3625 MH) (3607 MH) (3612 MH) (3618 MH) (3625 MH) E 6.10 E 9.60 E E (3125 PW) For water diluted acryl varnishes: Glattflor 5 mm ~ 15 /64 pile highly compacted plush for exceptional superior varnish absorption, for varnishing on even surfaces, the surfaces are extremely homogeneous without any blemishes (3125 PW) E 8.60 All rollers pictured here are fitting on our roller bows, refer to page 6. 4

5 Structure Roller structure rollers for plastic effects are only suitable for solventfree plastics. The cover is made of a seamless foam sleeve on the liquidtight roller body. These rollers are provided with a seal accepting only bow handles of series 32--S/SK. Moltopren Roller (8018 F F) Width 18 cm 25 cm ~7 1 /8 10 Structure: fine (8018 F) (8025 F) E 6.80 E 8.50 (8018 M M) Stucture: medium (8018 M) (8025 M) E 6.80 E 8.50 Structure: coarse (8018 G) (8025 G) E 6.80 E 8.50 Porosen Roller for particulary strong plastic effects. Covered with seamless Moltopren foam sleeve. (8018 G G) Width 18 cm 25 cm ~7 1 /8 10 (8018 P) (8025 P) E E (8018 P P) Bitumen Roller (3125 BL) robust design using full-length brass shaft and metal sides, heat-resistant, supplied with genuine lambskin, approx. 20 mm ~ 3 /4 pile, width 25 cm ~10. Fitting roller bow (3225 S/SK) E (3125 BL) Equalizing Roller (3625 E) mohair, for making structures on viscous coatings solvent-resistant, 25 cm ~10 width E (3625 E) Loop Roller (3725 S) 25 cm ~10 width solvent-resistant, only fitting on roller bow 3225 S/SK E (3725 S) 5

6 PPW-POLYPL AN-WERK ZEUGE GMBH (3207 D 3225 D) Roller Handle fitting on all rollers described before, galvanized steel bow handle 8 mm ~ 5 /16 diameter, M8 thread at end of handle, waxed removable square wooden grip or hollow plastic grip, two attachment models (3207 S 3230 S) Width 7 cm 12 cm 18 cm 25 cm 30 cm ~2 3 /4 4 3 /4 7 1 / Slide-on attachment + square wooden handle (3207 D) (3212 D) (3218 D) (3225 D) E 2.50 E 2.70 E 2.95 E 3.10 Screw-in attachment + square wooden handle (3207 S) (3212 S) (3218 S) (3225 S) (3230 S) E 2.60 E 2.90 E 3.10 E 3.25 E 4.35 Slide-on attachment + hollow plastic handle (3207 DK) (3212 DK) (3218 DK) (3225 DK) (3230 DK) E 2.50 E 2.70 E 2.95 E 3.10 E 3.95 (3207 DK 3230 DK) (3207 SK 3230 SK) (3201) Screw-in attachment + hollow plastic handle (3207 SK) (3212 SK) (3218 SK) (3225 SK) (3230 SK) E 2.50 E 2.80 E 2.95 E 3.10 E 4.25 (3200) Brass Screw (3200) for handles with screw E 0.60 Metal Hollow Handle (3201) 30 mm ~1 3 /16 diameter (3201) for all bow handles of series 32 with M8 internal screw, fitting broomsticks. E 5.80 (150 V) Extension Sticks (150 V) fitting all bow handles of series 32 with M8 internal screw thread and clamp, made of wood 150 cm ~60 long; 28 mm ~1 1 /8 diam. E Telescopic Elongator of light metal, extensible, with internal screw thread and bayonet fastener fitting on hollow plastic handle from 75 cm to 150 cm extensible (150 LM) E ~30 to ~60 from 150 cm to 300 cm extensible (300 LM) E ~60 to ~120 from 200 cm to 400 cm extensible (400 LM) E ~80 to ~160 (150 LM) 6

7 Large Area Roller < hard-wearing design, approx. 50 mm ~2 internal diameter The core is made of solvent-resistant, plastic impregnated hard paper. The advantage to a plastic tube is, that the roller will remain stiff. The roller won t wield, won t be deformed and the liquid coatings won t be moved. Width of roller 40 cm 60 cm 100 cm ~16 ~24 ~40 Perlon fur 18 mm ~ 3 /4 pile, twisted, ends roughened, superior material absorption, appropriate high coating (3140 P) (3160 P) (3199 P) (3160 P) (3160 PK) (3160 PG) E E E Perlon fur 12 mm ~ 1 /2 pile woven, black stripes for non-fuzzy coatings (3140PK) (3160PK) E E Perlon fur 8 mm ~ 5 /16 pile woven, black and yellow stripes for thin coating, absolutely non-fuzzy (3140 PG) (3160 PG) E E Mohair plush 4 mm ~ 3 /16 pile woven, goat hair (no plastics) for very thin coatings, to remove air bubbles (3660 MH) E (3660 MH) to fit above roller: (3260 U) U-Shaped Bow < adjustable with wing-screws, metal hollow handle for the extension by means of a stick. The U-Roller-Bows are fitting on roller bearings 8 mm ~ 5 /16. The bows are made of stainless steel, for that reason there will be hardly abrasion and the material won t hardly be dyed at the roller bearings. Moreover the roller bows won t get rusty after cleaning and long storing and can be used for a long time. Width 40 cm 60 cm 100 cm ~16 ~24 ~40 (3240 U) (3260 U) (3299 U) E E E

8 PPW-POLYPL AN-WERK ZEUGE GMBH (6060 P) (6100 P) Mini-Roller easy to exchange, 15 mm ~ 5 /8 internal diameter, mm ~1-1 3 /8 external diameter depending on the fur coat, solvent-resistant. (6150 P) Width 80 mm 100 mm 150 mm ~3 1 /8- ~4 ~6 Perlon fur 13 mm ~ 1 /2 (6060 P) (6100 P) (6150 P) E 1.65 E 1.75 E 2.75 (6100 MH) Mohair plush 4 mm ~ 5 /32 (6060 MH) (6100 MH) (6150 MH) E 2.85 E 3.45 E 4.70 (6100 N) Nylon fur 13 mm ~ 1 /2 (6060 N) (6100 N) (6150 N) E 1.65 E 2.05 E 2.85 (6150 PG) (6100 PG) Perlon fur 7 mm ~ 9 /32 (6100 PG) (6150 PG) E 1.80 E 2.75 (6150 PW) Glattflor 5 mm ~ 13 /64 (6100 PW) (6150 PW) E 1.80 E 2.75 (6100 PW) Handles for Mini-Roller galvanized steel bow 6 mm ~ 1 /4 diameter, fitting to all radiator rollers, excepting 6050P and 6320P round waxed wooden handle length: short approx. 30 cm ~12 (6220) E 1.30 medium approx. 45 cm ~18 (6260) E 1.30 long approx. 80 cm ~32 (6280) E 3.00 hollow plastic handle medium approx. 45 cm ~18 (6260 K) E 1.20 (6220) (6260 K) (6260) (6280) 8

9 Mini-Roller double thick (6320 P) Easy to exchange, 30 mm ~1 3 /16 internal diameter, 50 mm ~2 external diameter, 120 mm ~4 3 /4 width, perlon fur E 3.30 (6320 P) Handle for Mini-Roller double thick (6321) galvanized steel bow 6 mm ~ 1 /4 diameter with hollow plastic handle, approx. 42 cm ~16 3 /4 length E 1.20 (6321) Mini Roller Perlon fur, 15 mm ~ 5 /8 internal diameter, 60 mm ~2 3 /8 width Roller (6050 P) E 1.55 Handle (6250 K) E 0.90 (6050 P) 9

10 PPW-POLYPL AN-WERK ZEUGE GMBH Foam Roller of Moltopren, approx. 35 mm ~1 3 /8 diameter in total, suitable for varnishing and single-component plastics, not resistant to solvents. (6260) Width 60 mm 100 mm ~2 1 /2 ~4 Roller (6050 M) (6100 M) E 0.85 E 1.65 (6100 M) (6100 G) structure coarse (6100 G) E 1.65 Handle (6250 K) (6260) E 0.90 E 1.30 (6250 K) (6050 M) (6000 D) (6200 D) Corner Roller flat small roller, suitable for grooves, corners, etc., approx. 100 mm ~4 diameter in total, 35 mm ~1 3 /8 wide, nylon fur, with handle approx. 35 cm ~14 long Roller (6000 D) E 9.55 Handle (6200 D) E 1.55 Roller for Corrugated Plates < special roller for corrugated plates, width 13 cm ~5 1 /8, supplied with knitting-plush fur, approx. 22 mm ~ 7 /8 pile. Complete with roller bow handle and hollow plastic grip for extension. (3113 W) complete with handle (3113 W) E spare roller (3113 WE) E Scraper Grating with handle, galvanized corrugated wire. 30 x 22 cm ~12 x 8 5 /8 for rollers up to 18 cm ~7 1 /8 (3318) E x 26 cm ~12 x 10 1 /4 for rollers up to 25 cm ~10 (3318) (3325) E

11 Ring Brush (927) round brush with plastic band, pure bristles, vulcanized No dia. mm ~ 3 / / /8-1 1 /2-1 3 /4-2 E (927) Dabbing Brush (205) round special brush, 28 mm ~1 1 /8 long bristles, 40 mm ~1 5 /8 dia., light-coloured bristles, metal ferrule, rough handle E 7.65 (205) Joint Brush (600) light-coloured bristles, flat ferrule, short white handle. No Width mm bottom at ~ 7 /16 1 /2 5 /8 3 /4 7 /8 metal ferrule E Hollow-Stick-Brush (933) with nylon-bristles. Passing through the stick for cleaning liquids possible, conical plastic stick, resistant against oil and petrol. E 7.20 Dabbing Brush (632) brush in a wood body, 60 mm ~2 1 /2 width, 25 mm ~1 thick with grey stiff bristles. The stiff bristles air those places which cannot be reached by a roller E Barrier Skin Brush Moltopren foam material, leaves no brush marks, no bristles will fall out, not solvent-resistant Width 45 mm 60 mm ~1 3 /4 ~2 1 /2 (986) (987) E 2.40 E 2.70 Gel-Coat Brush (622 S)< black elastic China bristles, vulcanized, approx. 7 mm ~ 9 /32 thick, suitable for applying fine coats Width / /2 3 4 E (622) < light-coloured elastic bristles, otherwise as described above Width / /2 3 4 E Surface Brush (875) < plastic body with round plastic handle, pure bristles Width 70 mm 100 mm 120 mm ~2 3 /4 ~4 ~4 3 /4 Thickn. 30 mm 30 mm 30 mm ~1 3 /16 ~1 3 /16 ~1 3 /16 E Flat Brush (6406) < pure light-coloured bristles, flat unlacquered handles, wide metal collars, solvent-resistant Width mm ~ 1 /2 3 /4 1 3 / / /2-2 3 /4-3 1 /8-4 Thickn mm ~ 3 /8 7 /16 1 /2 9 /16 5 /8 11 /16 23 /32 3 /4 13 /16 E (600) (933) (632) (987) (622 S) (875) (6406) 11

12 PPW-POLYPL AN-WERK ZEUGE GMBH Priming Brush (400) with fibre bristles, 400 mm ~16 wide, with slanting stick holes, E 5.35 (400) Floor Brush (6400) 22 cm ~8 3 /4 wide, 2.5 cm ~1 thick, vulcanized, bristle length 55 mm ~2 3 /16, with stick holder E (6400 L) as above, but width 30 cm ~12 E (6400 K) as above, but bristle length 35 mm ~1 3 /8 E (6400) (6361) Façade Brush (6361) oval light-coloured full bristles, vulcanized, bristle length 65 mm ~2 1 /2, size 140 x 70 mm ~5 1 /2 x 2 3 /4 E (6932) Corner Brush (6932) round with angular handle, with plastic band, with screw, light-coloured bristles No dia. mm ~1 3 /8 1 1 /2 1 3 / /16 E Sparestick (6932 ST) E 1.00 (615) Corner Brush, metal-free (615) flat angular plastic handle, PA-ferrule, solvent-resistant, do not rust, light-coloured bristles Width / /2 3 Width 25 mm 40 mm 50 mm 60 mm 75 mm E (614) Corner Brush (614) flat < flat angular handle, approx. 40 cm ~15 3 /4 long, vulcanized, light-coloured bristles, solvent-resistant Width / /2 3 Width 25 mm 40 mm 50 mm 60 mm 75 mm E (6719) Diagonal Line Drawer (6719) with long handle, diagonal bristles, suitable for offsetting Width 15 mm 25 mm ~ 5 /8 1 E 2.65 E

13 Round Industrial Brush (9302) pure light-coloured bristles, plastic supporting band No dia.mm ~ 3 / / /8 1 1 /2 1 3 /4 2 E Round Brush (900S) pure black and special elastic China bristles, yellow supporting string No dia.mm ~ 3 / / /8 1 1 /2 1 3 /4 2 E Oval Shaped Brush (905S) pure light-coloured China bristles No. = mm ~1 3 / / /8 E Flat Brush (6406S) wide nickel band, pure black China bristles Width / /2 3 Width 25 mm 40 mm 50 mm 60 mm 75 mm E Flat Brush (6810 S) angular handle, pure black China bristles, copper-enamel ferrule Width 10 mm 15 mm 20 mm 25 mm 30 mm ~ 3 /8 5 /8 3 / /16 E (681 S) pure black China bristles, copper-enamel ferrule Width 10 mm 15 mm 20 mm 25 mm 30 mm ~ 3 /8 5 /8 3 / /16 E (9302) (900 S) (905 S) (6406 S) (6810 S) (681 S) Corner Brush (617 S) flat special type, extra strong, approx. 20 mm ~ 3 /4, pure black China bristles Width 70 mm 100 mm ~2 3 /4 4 E (612 S) flat angular handle, pure black China bristles, reinforced metal Width / /2 3 Width 25 mm 40 mm 50 mm 60 mm 75 mm E (617 S) (612 S) (611) flat angular handle, pure light-coloured bristles of superior quality Width / /2 3 Width 25 mm 40 mm 50 mm 60 mm 75 mm E (611) 13

14 PPW-POLYPL AN-WERK ZEUGE GMBH POLYPLAN Spiked Roller this spiked roller is to prevent uneveness when coating with solventresistant containing liquid plastics. It is to remove trapped air bubbles after coatings. The spiked roller is made of solvent-resistant plastic. The types E, L + R are pulled up on a plastic impregnated core of hard paper and so the roller will remain stiff. The roller won t wing, won t be deformed, the liquid coating won t be moved. The widths 50 cm ~20, 75 cm ~30 and 100 cm ~40 will be supplied with a V2A-U-shaped-bow. The U-bow has a bar with 8 mm diameter, so the bow can t be bended through transmission of the power. The bow is made of stainless steel, which has the advantage to galvanized steel, that there s almost no abrasion, the material will hardly be dyed at the roller bearings. Moreover the roller bow won t get rusty after cleaning a long storing and can be used for a long time. POLYPLAN Spiked Roller < roller diameter 68 mm ~2 11 /16, length of the spikes 11 mm ~ 7 /16 Width 7 cm 12 cm 18 cm 25 cm ~2 3 /4 ~4 3 /4 ~7 1 /8 ~10 (3807 E) (3812 E) (3818 E) (3825 E) E (3807 E 3899 E) Width 50 cm* 75 cm* 100 cm* ~20 ~30 ~40 (3850 E) (3875 E) (3899 E) E * these widths will be supplied with a U-shaped metal bow element made of stainless steel POLYPLAN Spiked Roller < roller diameter 88 mm ~3 1 /2, length of the spikes 21 mm ~ 13 /16 Width 7 cm 12 cm 18 cm 25 cm ~2 3 /4 ~4 3 /4 ~7 1 /8 ~10 (3807 L) (3812 L) (3818 L) (3825 L) E (3807 L 3899 L) Width 50 cm* 75 cm* 100 cm* ~20 ~30 ~40 (3850 L) (3875 L) (3899 L) E * these widths will be supplied with a U-shaped metal bow element made of stainless steel 14

15 POLYPLAN Spiked Roller < roller diameter 108 mm ~4 1 /4, length of spikes 31 mm ~1 7 /32 Width 7 cm 12 cm 18 cm 25 cm 50 cm* 75 cm* 100 cm* ~2 3 /4 4 3 /4 7 1 / (3807 R) (3812 R) (3818 R) (3825 R) (3850 R) (3875 R) (3899 R) E * these widths will be supplied with a U-shaped metal bow element made of stainless steel ( R) POLYPLAN Spiked Roller < loose discs: disc diameter 108 mm ~4 1 /4, length of spikes 31 mm ~1 7 /32 Width 7 cm 12 cm 18 cm 25 cm 50 cm* 75 cm* 100 cm* ~2 3 /4 4 3 /4 7 1 / (3807 S) (3812 S) (3818 S) (3825 S) (3850 S) (3875 S) (3899 S) E * these widths will be supplied with a U-shaped metal bow element made of stainless steel (3807 S 3899 S) POLYPLAN Spiked Roller < roller diameter 135 mm ~5 5 /16, length of spikes 60 mm ~2 3 /8, available only with a U-shaped metal bow element made of stainless steel Width 25 cm 50 cm 75 cm 100 cm ~ (3825 T) (3850 T) (3875 T) (3899 T) E (3825 T 3899 T) 15

16 PPW-POLYPL AN-WERK ZEUGE GMBH POLYPLAN Metal Spikeroller this type of spikeroller has very thin metal spikes, dia. 0.4 mm ~ 1 /64. (3625 KB) (3625 KB) < roller diameter 68 mm ~2 11 /16, length of the spikes 10 mm ~ 3 /8, 25 cm width ~10, complete with roller bow and metal hollow handle E (3625 LB) < roller diameter 84 mm ~3 5 /16', length of the spikes 20 mm ~ 3 /4', 25 cm width 10', complete with roller bow and metal hollow handle E (3650 KB) < roller diameter 68 mm ~2 11 /16, length of the spikes 10 mm ~ 3 /8, 50 cm width ~20, complete with U-shaped metal bow element made of stainless steel E (3650 KB) (3650 LB) < roller diameter 84 mm ~3 5 /16', length of the spikes 20 mm ~ 3 /4', 50 cm width 20', complete with U-shaped metal bow element made of stainless steel E Roller Cleaning Box (32B) < made of plastic, solvent-resistant, useful for fur roller and spiked roller type E, L, R and S to 25 cm ~10 width. Inner diameter 110 mm ~4 5 /16, inner height 330 mm ~13 3 /16 E (32 B) 16

17 Splash Guard for Roller for spiked roller and fur roller width 25 cm ~10, which can be used with an oneside guided bow, we can supply: Splash Guard (3825 C) < for clamping on a steel bow 8 mm ~ 5 /16 diameter, max. roller-diameter 110 mm ~4 11 /32, made of PP, solvent-resistant E 5.00 (3825 C) Splash Guard for U-shaped bow < for clamping on the rectangular part of the bow secured through the screw of handle made of PP, solvent-resistant (3850 C C) Width 50 cm 75 cm 100 cm ~20 ~30 ~40 (3850 C) (3875 C) (3899 C) E

18 PPW-POLYPL AN-WERK ZEUGE GMBH (3907 KK 3918 KK) (3907 M 3918 M) (3907 G 3918 G) (3907 A 3918 A) (3907 TL 3918 TL) (3907 K 3918 K) (3907 KG 3918 KG) (3907 L 3918 L) Laminating Rollers for airing Metal Disc Roller < loose metal discs of 40 mm ~1 5 /8 diameter, with flanged outer disc to cover up the nut, complete with screw-on bow handle of series 32* Width 7 cm 12 cm 18 cm ~2 3 /4 4 3 /4 7 1 /8 (3907 M) (3912 M) (3918 M) E all-metal roller of 22 mm ~ 7 /8 diameter, secured by means of an M8 countersunk brass nut, complete with handle of series 32* Width 7 cm 12 cm 18 cm ~2 3 /4 4 3 /4 7 1 /8 (3907 G) (3912 G) (3918 G) E all-polyamide roller of 25 mm ~1 diameter, countersunk nut, complete with handle of series 32* Width 7 cm 12 cm 18 cm ~2 3 /4 4 3 /4 7 1 /8 (3907 K) (3912 K) (3918 K) E all-teflon roller of 25 mm ~1 diameter, countersunk nut, complete with handle of series 32* Width 7 cm 12 cm 18 cm ~2 3 /4 4 3 /4 7 1 /8 (3907 TL) (3912 TL) (3918 TL) E Laminating Roller < Grooved Roller < Disc Roller < loose discs made of Hostalen, 34 mm ~1 3 /8 diameter, complete with screw handle of series 32* Width 7 cm 12 cm 18 cm ~2 3 /4 4 3 /4 7 1 /8 (3907 KK) (3912 KK) (3918 KK) E loose discs made of Hostalen, 48 mm ~1 7 /8 diameter, complete with screw handle of series 32* Width 7 cm 12 cm 18 cm ~2 3 /4 4 3 /4 7 1 /8 (3907 KG) (3912 KG) (3918 KG) E of tubular aluminium, longitudinally grooved, 50 mm ~2 diameter, secured with M8 countersunk nut, complete with screw handle of series 32* for extension Width 7 cm 12 cm 18 cm ~2 3 /4 4 3 /4 7 1 /8 (3907 A) (3912 A) (3918 A) E Laminating Roller with perlon bristles, polypropylene body, approx. 50 mm ~2 diameter in total, complete with screw handle of series 32* Width 7 cm 12 cm 18 cm ~2 3 /4 4 3 /4 7 1 /8 (3907 L) (3912 L) (3918 L) E * for extension pieces refer to page 6. On demand, grooved, disc and airing roller can be made within a short time to fit your model 18

19 Mini-grooved Roller < all-metal roller 14 mm ~ 9 /16 diameter, on nickel-plated one-side bow handle, 5 mm ~ 13 /64 diameter, secured by a countersunk nut M5, round wooden grip Width 60 mm 100 mm ~2 3 /8 4 (5060 G) (5100 G) E (5060 G G) Grooved Roller < of tubular aluminium longitudinally grooved, 21 mm ~ 13 /16 diameter, complete with 6 mm ~ 1 /4 diameter bow handle, secured by a nut M6 Width 100 mm 150 mm 180 mm ~ /8 (5100 A) (5150 A) (5180 A) E (5100 A 5180 A) Mini-disc Roller < small indented metal discs, 18 mm ~ 23 /32 diameter, on a nickel-plated one-side bow handle, 5 mm ~ 13 /64 diameter, flanged disc, secured by a nut M5, round wooden grip Width 60 mm 100 mm ~2 3 /8 4 (5060 RZ) (5100 RZ) E (5060 RZ RZ) Flexible Airing roller < with the flexible steel coil, slightly curved surfaces can be aired Width 95 mm ~3 3 /4-28 mm dia. ~1 1 /8 (3909 FL) E (3909 FL) Mini-disc Roller < small smooth metal discs, 15 mm ~ 5 /8 diameter, on nickel-plated one-side bow handle, 5 mm ~ 13 /64 diameter, flanged disc, secured by a nut M5, round wooden grip Width 60 mm 100 mm ~2 3 /8 4 (5060 R) (5100 R) E Laminating Roller 30 mm ~1 3 /16 dia., with black nylon bristles, spirally wound up, with nickel-plated, one-sided handle 5 mm ~ 13 /64 dia., round wooden grip Width 100 mm 150 mm ~4 6 (5100 L) (5150 L) E as above, with 21 mm ~ 13 /16 diameter Width 50 mm 75 mm 100 mm ~2 3 4 (5050 LK) (5075 LK) (5100 LK) E (5060 R R) (5100 L LK) 19

20 PPW-POLYPL AN-WERK ZEUGE GMBH (4408 TL 4808 TL) (5030 TL 5060 TL) Grooved Roller (5100 K) < all-polyamide roller, 14 mm ~ 5 /8 diameter, 100 mm ~4 wide, on nickel-plated bow handle, 5 mm ~ 13 /64 diameter, secured by a nut M5 E 7.95 Mini-grooved Roller < all-teflon roller fitted to one-side nickel-plated bow 4 mm ~ 5 /32- diameter, secured by a slotted cap nut Rollerwidth 40 mm 8 mm dia. (4408 TL) E ~1 5 /8 ~ 5 /16 80 mm 8 mm dia. (4808 TL) E ~3 1 /8 ~ 5 /16 same as above, but with a bow handle of 5 mm ~ 13 /64 diameter and secured by a nut M5 Rollerwidth 40 mm 10 mm dia. (5041 TL) E ~1 5 /8 ~ 3 /8 60 mm 10 mm dia. (5061 TL) E ~2 3 /8 ~ 3 /8 (5080 TL 5100 TL) 100 mm 10 mm dia. (5101 TL) E ~4 ~ 3 /8 (6090) Rollerwidth 30 mm 15 mm dia. (5030 TL) E ~1 3 /16 ~ 5 /8 40 mm 15 mm dia. (5040 TL) E ~1 5 /8 ~ 5 /8 60 mm 15 mm dia. (5060 TL) E ~2 3 /8 ~ 5 /8 80 mm 15 mm dia. (5080 TL) E ~3 1 /8 ~ 5 /8 100 mm 15 mm dia. (5100 TL) E ~4 ~ 5 /8 Corner Airing Roller < Polyamide body, 60 mm ~2 3 /8 dia., 50 mm ~2 wide, 90 degrees, with bow handle 6 mm ~ 1 /4 thick and 40 cm ~16 long, 9 grooves (6090) E (5090 M) with 4 metal discs, 50 mm ~2 dia., with bow handle 6 mm ~ 1 /4 dia., total length 35 cm ~14 (5090 M) E 7.90 TEFLON body 50 mm ~2 dia., 15 mm ~ 5 /8 wide, 90 degrees, with bow handle 6 mm ~ 1 /4 dia., total length 35 cm ~14, 3 grooves (1590 TL) E (1590) Polyamide body 50 mm ~2 dia., 15 mm ~ 5 /8 wide, 90 degrees, with bow handle 6 mm ~ 1 /4 dia., total length 35 cm ~14, 3 grooves (1590) E (5014 TL) Grooved Roller < TEFLON body 48 mm dia., 10 mm ~ 3 /8 width, with 5 mm ~ 13 /64 dia. bow handle, total length 35 cm ~14, 3 grooves (5014 TL) E

21 TO WALK OVER FRESH COATINGS POLYPLAN Spike Slipper this slippers are for walking over higher layers and are suitable for uneven floors. Because of recessed set screws the nails get a better stability compared to other spiked shoes. A better support is ensured because of the boundary of sides. The straps can be fixed easily and they don t pass below the sole. POLYPLAN Spike Slipper (3700 K) < complete with pointed hardened steel spikes and straps with velcro fastener E (3700 K) POLYPLAN Spike Slipper (3700) < complete with pointed hardened steel spikes 30 mm long and straps with buckles and tongues E pairs of replacement spikes per Slipper-pair are required to equip the slippers again (3700) Replacement spike (3800 N) < pointed, 30 mm ~1 3 /16 length, each E 0.25 Replacement spike (3800 NG)< pointed, 18 mm ~ 3 /4 length, each E 0.25 Replacement spike (3800 NL)< pointed, 40 mm ~1 5 /8 length, each E 0.25 Replacement spike (3800 SS)< blunt, 24 mm ~ 15 /16 length each E 0.35 POLYPLAN Spike Slipper (3700 S) < complete with blunt hardened steel spikes and straps with velcro fastener E (3700 S) 21

22 PPW-POLYPL AN-WERK ZEUGE GMBH Squarepointed shoes (3803) smooth < flat, made of plastic material, 200 x 400 mm ~7 7 /8 x 16 bearing area, complete with rubber straps, fit above every size of shoes 1 pair E Rubber straps (3803 G)< for squarepointed shoes each E 3.00 (3803) POLYPLAN Spiked Shoes (3800 S) < to walk over fresh coated roofs. The shoes have a polypropylene body and blunt spikes. Straps with buckles and tongues can readily be fastened under any shoe 1 pair E (3800 S) Replacement Spike (3800 SS) < for POLYPLAN Spiked Shoes, 1 blunt spike 22 pieces for 1 pair each E

23 POLYPLAN Spiked Shoes (3800) < to walk over fresh layers without leaving any marks. The shoes have a polypropylene body and pointed hardened steel spikes. Straps with buckles and tongues can readily be fastened under any shoe per pair E Replacement Straps straps with buckles and tongues, short (3800 EK) < each E 3.75 Straps with buckles and tongues, long (3800 EL)< each E 4.25 POLYPLAN Spiked Shoes (3800K) < as above, but fitted out with straps with velcro fasteners per pair E (3800) Replacement Straps straps with velcro fasteners, short (3800 KK)< each E 3.50 Straps with velcro fasteners, long (3800 KL) < each E 3.90 Replacement Spike (3800 N) < for POLYPLAN Spiked Shoes, 1 pointed hardened steel spike, length 30 mm ~1 3 /16 22 pieces for 1 pair each E 0.25 (3800 K) Replacement Spike (3800 NL) < for POLYPLAN Spiked Shoes, 1 pointed hardened steel spike, length 40 mm ~1 5 /8 22 pieces for 1 pair each E

24 PPW-POLYPL AN-WERK ZEUGE GMBH For the application of adhesives and coatings, mainly with fillers, toothed blades are particularly suited. Varying types of toothed blades are, of course, required for different coating heights. We supply types of toothed blades as shown on the next page (scale 1:1). Width of the toothed blades is 280 mm ~11. Trowel (999) < fitted with clamps to hold the exchangeable toothed blades. The trowel is made of fine polished steel, light metal support with handy, unvarnished wooden grip. Blade size 280 x 100 mm ~11 x 4 E (999) (999 L) < as above but lefthanded E Adhesive Spreader (777) fitted with clamps to hold the exchangeable toothed blades. The adhesive spreader is made of aluminium to make it light and yet stable. Width of blade 280 mm ~11 E (777) Large-Surface Scraper (656) < fitted with clamps of stainless steel to hold two toothed blades. The large-surface scraper will be delivered complete with stick holder, it is also suitable for manual coatings. Blade length 560 mm ~22 E39.00 (656) 24

25 Toothed blades< The exchangeable toothed blades (777 E), width 280 mm ~11, are available in the following shapes: H 2,0 H 2,6 H 1,2 L 2,3 L 2,9 L 1,4 S 2,7 S 2,1 S 0,7 A 2,75 C 2,75 F 3,65 G 3,65 H 2,6 L 1,6 S 1,4 H 2,4 H 1,5 H 2,2 L 1,6 L 1,8 L 1,8 S 1,6 S 1,2 S 0,2 -K 3,65 3 3,65 5 4,30 7 4,30 H 4,4 L 2,8 S 0,2 H 2,0 H 3,2 L 2,2 L 3,6 S 3,0 S 3,4 13 3, , ,75 H 4,1 L 4,2 S 7,5 H 2,7 H 1,0 H 1,5 L 3,0 L 1,4 L 1,5 S 5,0 S 0,6 S 0,5 21 4, , , ,65 H 2,7 L 2,3 S 3,3 H 4,2 H 6,0 H 4,5 L 5,7 L 6,0 L 4,5 S 0,6 S 6,0 S 4,5 25 2,75 26* 4, ,30 30* 4,30 H 4,8 L 4,5 S 6,5 H 2,0 H 2,6 H 3,0 L 3,0 L 2,2 L 3,2 S 1,6 S 2,0 S 3,0 32 2, , , ,30 H 4,0 L 4,0 S 4,0 H 4,8 H 0,7 H 2,0 L 5,0 L 1,0 L 1,5 S 5,0 S 0,5 S 1,5 37* 4, , , ,30 H 3,0 L 4,0 S 1,6 H 5,5 H 7,0 H 5,0 L 6,5 L 7,5 L 4,0 S 0,5 S 8,5 S 2,0 48* 4,30 49* 4, , ,65 H 0,7 L 1,7 S 0,3 H 5,1 L 10,3 S 0,2 H 5,8 L 4,2 S 2,8 H 8,0 L 6,5 S 3,3 67* 4,30 70* 4,30 71* 4,30 78* 4,30 H 7,7 L 8,2 S 0,5 H 9,2 L 10,0 S 0,2 H 3,4 L 4,2 S 0,2 92* 4, ,30 95* 4,30 H 5,2 L 6,2 S 0,2 * supplied only with one toothed edge. All serrations shown in actual size (1:1). The mentioned measurements depend on manufacture of material and can depart insignificant. H Height of teeth in mm L Gap between teeth in mm S Width from top of teeth in mm 25

26 PPW-POLYPL AN-WERK ZEUGE GMBH (199-**) Layer-Thickness-Trowel (199-**) < (DGBM) made of stainless steel. This Layer-Thickness Trowel doesn t determine the height of coatings through metal teeth/toothed blades, but through 4 discs, which are welded to the trowel. Because of the round form of the discs, it doesn t matter in which angle the trowel will be held to the ground. The distance between the edge of the trowel and the ground will always be exact the diameter of the discs and there couldn t result differences in the heigth because of wrong handling. The discs are made of thicker material as usual toothed blades, so there won t be so much abrasion. The Layer-Thickness-Trowel is available for the below mentioned height of coatings from stock. Each other size certainly can be produced according to your inquiry. for height of coatings 2.5 mm ~ 3 /32 ( ) for height of coatings 3.0 mm ~ 1 /8 ( ) for height of coatings 4.0 mm ~ 5 /32 ( ) for height of coatings 5.0 mm ~ 13 /64 ( ) E / each (299-**) Layer Thickness-Batten (299-**) < corresponding to the principle of the Layer-Thickness-Trowel. This batten is made of stainless steel to which the 4 discs are welded. The Layer-Thickness-Batten can be used like usual toothed blades and put into the adhesive spreader (777) or trowel (999). for height of coatings 2.5 mm ~ 3 /32 ( ) for height of coatings 3.0 mm ~ 1 /8 ( ) for height of coatings 4.0 mm ~ 5 /32 ( ) for height of coatings 5.0 mm ~ 13 /64 ( ) E / each Sale + Delivery for german customers of the articles (199-**) and (299-**) will be directly through the company: IK Vertrieb & Dienstleistung Ilona Kaupper, Wickenreuth 8a, Kulmbach, Phone: Fax: Service@ik-vertrieb.de 26

27 Floor Finish Scraper of cast aluminium, for applying and spreading of liquid synthetic finishing compounds, with the adjustable levelling screeder the coating height can be easily adjusted from 0 to 10 mm ~0 to ~ 13 /32. (680 K) 58 cm ~22 7 /8 width with 6 gliding spikes E (680) 80 cm ~31 1 /2 width with 8 gliding spikes E (680K) (680) Floor Finish Scraper (690 K) of cast aluminium. Corresponding to floor finish scraper (680 K), but the screwed, curved V2A screeder is especially useful for thinner liquid coatings. E (690 K) 27

28 PPW-POLYPL AN-WERK ZEUGE GMBH Large-Surface Jaggy-Scraper 650 mm ~26 wide, consisting of: (76) + (76 E ) Holding Device for Large-Surface Jaggy Scraper (76) < with stick holder, of angular steel, without blade E (76 E ) picking up : Large-Surface Jaggy-Blades 645 mm ~25 3 /8 wide, 100 mm ~4 high, made of hardened spring band steel, 0.6 mm ~ 1 /32 thick: available in serrations shown in actual size (1:1) refer to page 25 Serration Shape 05 Shape 37 Shape 07 Shape 48 Shape 23 Shape 49 Shape 25 Shape 55 Shape 26 Shape 78 Shape 34 Shape 92 Shape 35 Shape 93 Shape 36 Shape 95 order no. (76E ) each E 8.90 Floor Finish Scraper for Large Surfaces (677) width 80 cm ~32, with attachment for handle. The scraper has two adjustable runners permitting a passing height from 6 to 30 mm, ~ 15 /64 to ~1 3 /16. E Spare blade (677 E) E 7.40 Spare runners (677 F) 1 pair E (677) 28

29 NEU Layer-Thickness-Blades made of stainless steel. The Layer-Thickness-Blades (79-**) are fitting on the Holding Device (76) for Large-Surface Jaggy Scraper as pictured. The Layer-Thickness-Scraper can be held in each position without changing the height of he coating the flowing-through under the edge of the blade. (76) + (79-**) (76) + (79-**) Layer-Thickness-Blades (79-**) < for height of coating 2.5 mm ~ 3 /32 (79-025) for height of coating 3.0 mm ~ 1 /8 (79-030) for height of coating 4.0 mm ~ 5 /32 (79-040) for height of coating 5.0 mm ~ 13 /64 (79-050) E / each (79-**) 29

30 PPW-POLYPL AN-WERK ZEUGE GMBH Tooth Squeegee Aluminium Support (59) < of cast aluminium. width 58 cm ~22 7 /8, without rubber blade complete with wingscrew and and clamping screeder E (59) + (59 E ) Rubber Blade (59 E 00)< lightcoloured, smooth E (59 E ) Rubber Blade < lightcoloured Neopren-blades 8 mm ~ 5 /16 thick, for tooth squeegee as above, pointed teeth: Height: 1 mm 2 mm 3 mm 4 mm 5 mm 6 mm 7 mm ~ 3 /64 5 /64 1 /8 5 /32 13 /64 15 /64 9 /32 (59 E 01) (59 E 02) (59 E 03) (59 E 04) (59 E 05) (59 E 06) (59 E 07) 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm ~ 5 /16 23 /64 13 /32 7 /16 15 /32 33 /64 9 /16 (59 E 08) (59 E 09) (59 E 10) (59 E 11) (59 E 12) (59 E 13) (59 E 14) E Hand Tooth Squeegee with stick (57) < width 26 cm ~10 1 /4, with extension elongator 60 cm ~24 long, without rubber blade E (57) + (57 E ) Rubber Blade < indented lightcoloured Neoprene-blades 8 mm ~ 5 /16 thick for hand tooth squeegee (57) as above or with wooden handle (56): Height: 1 mm 2 mm 3 mm 4 mm 5 mm 6 mm 7 mm ~ 3 /64 5 /64 1 /8 5 /32 13 /64 15 /64 9 /32 (57E01) (57 E02) (57 E03) (57 E04) (57 E05) (57 E06) (57 E07) 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm ~ 5 /16 23 /64 13 /32 7 /16 15 /32 33 /64 9 /16 (57 E08) (57 E09) (57 E10) (57 E11) (57 E12) (57 E13) (57 E14) E (57 E ) Rubber Blade (57E00) < for hand tooth squeegee (57) or (56), lightcoloured, smooth E

31 Hand Tooth Squeegee with wooden handle (56) < width 26 cm ~10 1 /4, without rubber blade, with light-metal support and wooden grip complete with wingscrew and and clamping screeder E Spread Scraper (1727)< aluminium support, width 40 cm ~15 3 /4 Because of the adjustable levelling pins it is possible to fix and control the height of the floor covering, also you can use it for spreading the mortar constantly on the surface. E (56) + (57 E ) (1727) POLYPLAN Spiked Prop (3802) < with unlaquered wooden handle, made of aluminium, 100 x 200 mm ~4 x 8, 8 mm ~ 5 /16 thick, with 4 spikes E (3802) 31

32 PPW-POLYPL AN-WERK ZEUGE GMBH (1714) Rubber Wiper aluminium support with 45 mm ~1 3 /4 rubber blade, replaceable Width 40 cm 60 cm ~16 ~24 (1714) (1716) E Spare Rubber Blade for rubber wiper, 4 cm ~1 1 /2 high 40 cm 60 cm like (1717 B) but 2 cm ~ 3 /4 ~16 ~24 higher black (1717 A) (1717 B) (1717 BH) E (4645) oil- 40 cm 60 cm resistant ~16 ~24 light- (1717 AO) (1717 BO) coloured E (1734) Foam Rubber Water Sweeper metal support, double sponge rubber 35 mm ~1 3 /8 thick Width 45 cm 60 cm ~18 ~24 (4645) (4660) E (655) stable wooden mounting, stick holder, double sponge rubber 35 mm ~1 3 /8 thick Width 40 cm 60 cm ~16 ~24 (1734) (1736) E (657) Surface-Scraper (655) width of blade 600 mm ~24, height 45 mm ~1 3 /4, made of stainless hardened spring band steel 0.4 mm thick ~ 1 /64, curved plywood handle, with holes to fit the stick holder E (211) (657 Y) (280) Stick Holder (657) made of light metal, complete with screws and wing nut, fit above scraper 655 and 656 Y-Stick Holder (657 Y) strong type, made of galvanized steel, to squeeze and screw down on scraper 655 and 656. fit above stick with 28 mm ~1 1 /8 diameter Scatter Tub (211) with trough of plastic, maximum filling amount 18 l, complete with 2 carrying straps Scoop (280) < of aluminium, available in the following sizes: E 6.90 E E Total length 290 mm 350 mm 400 mm 11 3 /8 ~14 ~16 E

33 Concave tapered trowels with 50 mm radius Concave tapered trowel for floors (94 R)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 80 mm ~3 5 /32 height of skirting board, corner radius 50 mm ~2, 10 mm ~ 13 /32 thickness of skirting board, 140 x 200 mm ~5 1 /2 x ~7 7 /8 contact width- E mm 200 mm r = 50 mm 10 mm 80 mm (94 R) (94 N)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 50 mm ~2 height of skirting board, corner radius 50 mm ~2, 10 mm thickness of ~ 13 /32 skirting board, 140 x 200 mm ~5 1 /2 x ~7 7 /8 contact width- 140 mm 200 mm r = 50 mm 10 mm 50 mm (94 N) E (94 F)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 80 mm ~3 5 /32 height of skirting board, corner radius 50 mm ~2, without skirting board, 140 x 200 ~5 1 /2 x ~7 7 /8 mm contact width E mm 190 mm r = 50 mm 80 mm (94 F) Concave tapered corner trowel for floors (94 ER)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 45 degree, 80 mm height ~3 5 /32 of skirting board, corner radius 50 mm ~2, 10 mm ~ 13 /32 thickness of skirting board, 110 x 350 mm ~4 5 /16 x ~13 3 /4 contact width E mm 170 mm r = 50 mm 10 mm 80 mm (94 ER) (94 EF)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 45 degree, 80 mm ~3 5 /32 height of skirting board, corner radius 50 mm ~2, without skirting board, 110 x 350 ~4 5 /16 x ~13 3 /4 mm contact width E mm 160 mm r = 50 mm 80 mm (94 EF) Round Trowel (94 K)< with stainless steel blade approx. 1.0 mm ~ 3 /64, radius 50 mm ~2, 170 mm length ~4 3 /4 E r = 50 mm (94 K) Profile Trowel (94 P)< with curved blade of stainless steel, radius 50 mm ~2, 250 mm ~10 length, 65 mm ~2 9 /16 blade width E r = 50 mm (94 P) (94 PS)< with curved blade of stainless steel, ends bevelled on both sides, radius 50 mm ~2, 250 mm ~10 length, 65 mm ~2 9 /16 blade width E r = 50 mm (94 PS) 33

34 PPW-POLYPL AN-WERK ZEUGE GMBH 10 mm Concave tapered trowels with 30 mm corner radius (91 R) 120 mm 160 mm r = 30 mm 80 mm Concave tapered trowel for floors (91 R)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 80 mm ~3 5 /32 height of skirting board, corner radius 30 mm ~1 3 /16, 10 mm ~ 13 /32 thickness of skirting board, 120 x 200 mm ~4 3 /4 x ~7 7 /8 contact width E (91 N) 120 mm 160 mm r = 30 mm r = 30 mm 10 mm 50 mm 80 mm (91 N)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 50 mm ~2 height of skirting board, corner radius 30 mm ~1 3 /16, 10 mm ~ 13 /32 thickness of skirting board, 120 x 200 ~4 3 /4 x ~7 7 /8 mm contact width E (91 F)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 80 mm ~3 5 /32 height of skirting board, corner radius 30 mm ~1 3 /16, without skirting board, 120 x 200 mm ~4 3 /4 x ~7 7 /8 contact width E mm 150 mm (91 F) (91 ER) 120 mm 160 mm r = 30 mm 10 mm 80 mm Concave tapered corner trowel for floors (91 ER)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 45 degree, 80 mm ~3 5 /32 height of skirting board, corner radius 30 mm ~1 3 /16, 10 mm ~ 13 /32 thickness of skirting board, 120 x 350 mm ~4 3 /4 x ~13 3 /4 contact width E r = 30 mm 80 mm (91 EF)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 45 degree, 80 mm ~3 5 /32 height of skirting board, corner radius 30 mm ~1 3 /16, without skirting board, 120 x 350 mm ~4 3 /4 x ~13 3 /4 contact width E (91 EF) 120 mm 150 mm Round Trowel (91 K)< with stainless steel blade approx. 1.0 mm ~ 3 /64, radius 30 mm ~1 3 /16, 170 mm length ~6 3 /4 E r = 30 mm (91 K) Profile Trowel (91 P)< with curved blade of stainless steel, radius 30 mm ~1 3 /16, 250 mm length ~10, 65 mm ~2 9 /16 blade width E r = 30 mm (91 P) (91 PS)< with curved blade of stainless steel, ends bevelled on both sides, radius 30 mm ~1 3 /16, 250 mm length ~10, 65 mm ~2 9 /16 blade width E r = 30 mm (91 PS) 34

35 Concave tapered trowels with 15 mm corner radius 10 mm Concave tapered trowel for floors (95 R)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 80 mm ~3 5 /32 height of skirting board, corner radius 15 mm ~ 19 /32, 10 mm ~ 13 /32 thickness of skirting board, 120 x 200 ~4 3 /4 x ~7 7 /8 mm contact width (95N) < with stainless steel blade approx. 1.0 mm ~ 3 /64, 50 mm height of skirting board, corner radius 15 mm ~ 19 /32, 10 mm ~ 13 /32 thickness of skirting board, 130 x 200 mm ~5 1 /8 x ~7 7 /8 contact width (95 F)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 80 mm ~3 5 /32 height of skirting board, corner radius 15 mm ~ 19 /32, without skirting board, 120 x 200 mm ~4 3 /4 x ~7 7 /8 contact width E E E r = 15 mm 120 mm 145 mm r = 15 mm 130 mm 145 mm r = 15 mm 120 mm 135 mm 80 mm 10 mm 50 mm 80 mm (95 R) (95 N) (95 F) Concave tapered corner trowel for floors (95ER) < with stainless steel blade approx. 1.0 mm ~ 3 /64, 45 degree, 80 mm ~3 5 /32 height of skirting board, corner radius 15 mm ~ 19 /32, 10 mm ~ 13 /32 thickness of skirting board, 120 x 350 mm ~4 3 /4 x ~13 3 /4 contact width (95 EF)< with stainless steel blade approx. 1.0 mm ~ 3 /64, 45 degree, 80 mm ~3 5 /32 height of skirting board, corner radius 15 mm ~ 19 /32, without skirting board, 120 x 350 mm ~4 3 /4 x ~13 3 /4 contact width E E r = 15 mm 120 mm 145 mm r = 15 mm 120 mm 135 mm 10 mm 80 mm 80 mm (95 ER) Joint trowels < with stainless steel blade Width 8 mm 10 mm 12 mm 14 mm 5 /16 13 /32 1 /2 9 /16 (66 R 08) (66 R 10) (66 R 12) (66 R 14) E (66 R 10) (95 EF) Corner trowel for outer corners (402 A)< for sharp corners, blade approx. 1.0 mm ~ 3 /64 thick, stainless steel size: 60 x 80 mm ~2 3 /8 x 3 5 /32 E 6.70 Corner trowel for inner corners (402 B)< for sharp corners, blade approx. 1.0 mm ~ 3 /64 thick, stainless steel size: 60 x 80 mm ~2 3 /8 x 3 5 /32 E 6.70 (402 A) (402 B) 35

36 PPW-POLYPL AN-WERK ZEUGE GMBH Plaster Spatula (404 R) < blade of stainless steel Width 40 mm 60 mm 80 mm ~1 5 /8 2 3 /8 3 1 /8 E (404 R) (411 R) (409 R) (190) (408 R) (181) Trowel, French Type (411 R)< so called Cat s Tongue. Blade of stainless steel Blade length 140 mm ~5 1 /2 (411)< forged of one piece, non stainless Blade length 140 mm ~5 1 /2 Trowel, Bern Type (409 R)< blade of stainless steel Blade length 120 mm 140 mm ~4 3 /4 5 1 /2 E (409) < forged of one piece, non stainless Blade length 120 mm 140 mm ~4 3 /4 5 1 /2 E Tile Layer s Trowel Hamburg Type (190) < forged of one piece, bright-polished, wooden grip Blade length 160-mm ~6 1 /4 Plaster Trowel (408 R)< blade of stainless steel Blade length 160 mm 180 mm ~6 1 /4 7 1 /8 E (408) < forged of one piece of steel, non-stainless Blade length 160 mm 180 mm ~6 1 /4 7 1 /8 E E 5.70 E 5.40 E (180) (98) (194) Tongue Trowel (181) < forged of one piece steel, bright-polished, Blade length 170 mm ~6 3 /4 E 6.00 Pointed Trowel (180) < forged of one piece of steel, bright-polished, wooden grip Blade length 140 mm ~5 1 /2 E 5.85 Mason s Trowel (98) < forged of one piece of steel, polished, riveted polished wooden handle with taper ferrule Blade length 220 mm ~8 5 /8 E Roofer s Trowel (194) < bright-polished with wooden grip Blade width 30 mm ~1 3 /16 Blade length 260 mm ~10 1 /4 E

37 Circular Trowel (425) < hardened and polished blade of stainless steel, with a round and conical shape, thickness of blade 0.7 mm ~ 1 /32, with light-metal support and wooden grip, Size 80/100 x 280 mm ~3 1 /8 / 4 x 11 E (425) Pointed Trowel (423) < hardened and polished blade of stainless steel, with a pointed and conical shape, thickness of blade 0.7 mm ~ 1 /32, with light-metal support and wooden grip, Size 90/100 x 280 mm ~3 35 /64 / 4 x 11 E (423) Flooring Trowel (426) < with rounded blade on both sides, made of stainless steel, Size 425 x 125 mm ~17 x 5 blade thickness 1.0 mm ~ 3 /64 with wooden grooved handle and continuos screwed pivot E (426) Smoothing Trowel for Large Surfaces (420) < hardened and polished steel blade, compact wooden grip, blade thickness 1.1 mm ~ 3 /64 Size 480 x 130 mm ~19 1 /8 x 5 1 /8 - E (420) (420 R)< stainless hardened steel blade, compact wooden grip, blade thickness 1.0 mm ~ 3 /64 Size 480 x 130 mm ~19 1 /8 x 5 1 /8 - E (420R) Ixel Trowel (195) < with a rounded and arched blade of stainless steel, thickness 1.2 mm ~ 3 /64, blade length 260 mm ~10 1 /4, width 60 mm ~2 3 /8 E (195) 37

38 PPW-POLYPL AN-WERK ZEUGE GMBH (422) Smoothing Trowel, Sword Type (422)< hardened and polished steel blade 80 x 100 mm ~3 1 /8 x 4, thickness 1.2 mm ~ 3 /64, blade length 500 mm ~20, light-metal support and wooden grip E (422 B)< hardened and polished steel blade 80 x 100 mm ~3 1 /8 x 4, thickness 0.7 mm ~ 1 /32, blade length 500 mm ~20, light-metal support and wooden grip E (422 R)< stainless hardened steel blade 80/115 x 500 mm ~3 1 /8 / 4 1 /2 x 20, thickness 1.0 mm ~ 3 /64, light-metal support and waxed wooden grip E (422 R) (422 RB)< stainless hardened steel blade 80/115 x 500 mm ~3 1 /8 / 4 1 /2 x 20, thickness 0.7 mm ~ 1 /32, light-metal support and waxed wooden grip E Swedish Trowel (421) < hardened steel blade 60 x 120 mm ~2 3 /8 x 4 3 /4, blade length 500 mm ~20, thickness 0.7 mm ~ 1 /32, with wooden grooved handle and continuos screwed pivot E (421) 38

39 Smoothing Trowel (92) < with fine-polished steel blade 0.7 mm ~ 1 /32 thick, blade size 280 x 130 mm ~11 x 5 1 /8, light-metal support and wooden grip E 6.60 (92 R)< of stainless hardened steel, thickness of blade 0.7 mm ~ 1 /32, blade size 280 x 130 mm ~11 x 5 1 /8, light-metal support and wooden grip E 8.00 (92 R) Smoothing Trowel small (92 Rk) < of stainless hardened steel, thickness of blade 0.7 mm ~ 1 /32, blade size 250 x 100 mm ~10 x 4, light-metal support and wooden grip E 7.00 (92 Rk) Smoothing Trowel (92 K) < of impact-resistant PVC, thickness of blade 3 mm ~ 1 /8, blade size 280 x 130 mm ~11 x 5 1 /8, light-metal support and wooden grip, non-resistant to solvent E (92 K) 39

40 PPW-POLYPL AN-WERK ZEUGE GMBH Wood Float (444)< base approx. 14 mm thick ~ 9 /16, with plastic grip.. Blade size 14 x 28 cm ~5 1 /2 x 11 E 5.70 (444) Float Plates for glueing to wood float (444), intended for elutriation work. Blade size 14 x 28 cm ~5 1 /2 x 11 Cellular caoutchouc plate black (445 Z) E 3.60 sponge rubber plate red (445 S) E 3.60 felt plate brown (445 F) E 4.70 (445 Z) (445 S) (445 F) 40

41 Epoxide Joint Board (447)< with special-rubber-support 250 x 110 mm ~9 7 /8 x 4 11 /32 and plastic handle E Epoxide Cleaning Trowel (193) trowel plate made of synthetic material, with hook and loop fastening, size 230 x 110 mm ~9 1 /16 x 4 11 /32, complete with one grinding and cleaning fleece each E (447) Grinding Fleece (193 A) hard type, size 250 x 120 mm ~9 7 /8 x 4 3 /4 E 3.95 (193) (193 B) (193 A) Cleaning Fleece (193 B) soft type, size 250 x 120 mm ~9 7 /8 x 4 3 /4 E 7.10 Rubber Smoothing Surfacer < the rubber sheet is 4 mm ~ 5 /32 thick and inserted into wooden back of 40 mm ~1 5 /8. Width 180 mm 280 mm 7 1 /8 11 (4150) (4151) E (4150) Surface Filler < made of 5 mm ~ 13 /64 thick PERBUNAN, thus oil-resistant, otherwise same as rubber smoothing surfacer Width 180 mm 280 mm 7 1 /8 11 (4160) (4161) E (4160) All-Purpose Sponge (4340) made of synthetic material, angular, size approx. 200 x 110 x 65 mm ~7 7 /8 x 4 5 /16 x 2 9 /16 E 1.20 (4340) Rust Scraper (128) heavy design, blade forged of one piece, perfect junction with beech wood handle by means of two rivets Width of blade 85 mm ~3 3 /8 Total length 950 mm ~37 3 /8 E Floor Scraper Support (850) handle of tubular steel, varnished grey. Overall length 150 cm ~60, without blade E (128) Spare blade (850 E) width 300 mm ~12, height 115 mm ~4 1 /2, made of steel E 7.50 ( E) 41

42 PPW-POLYPL AN-WERK ZEUGE GMBH Solar Balance For exact weighing out portions of resin up to 10 kg respectively 50 kg. Very good suitable for utilization on building grounds with its dust-proof protected and closed form. The solar balance is always ready for use and easy to transport, because you don t need any adapter or battery. Excessly contained energy will be stored and used by bad lightning. The adjustments will be simply implement with one function key. Hold-function for storing the display, as well as automatically turn-off and zeroizing are available. The supporting plate is about 30 x 30 cm (~11 3 /4 x 11 3 /4 ) big and made of break-proof plastic. Availabe in two types: up to 10 kg weight - 10 gr display partition: (2310) E up to 50 kg weight - 50 gr display partition: (2350) E Prices subject to be changed without notice! 42

43 Mortar-Mixing-Cart (2200) < The mortar-mixing-cart 2200 is configured to mix approx. 50 kg synthetic- or mineralbounded mortar homogeneously in 2 or 3 minutes. You can evacuate the mortar because of the height of the mortar-mixing-cart directly into a barrel or barrow. To this you open the evacuation shutter in the mixing drum while rotation of the mixing apparatus and the mortar falls from the mixing drum into the barrel. You can use a barrel with a maximal height of 65 cm ~25 5 /8. The mortar-mixing-cart can easily be cleaned. You can simply take out the square axel drive shaft from the gearing out of the mixing drum. Transportation of the mortar-mixing-cart in a passenger car is possible, because you can unscrew the legs of the cart. Technical data supply voltage: 230 V / 50 Hz nominal capacity: 1.1 kw nominal current: 9.0 A protective system: IP 54 speed of mixing apparatus: 35 U / min measurements: height 105 cm ~42 width 70 cm ~28 length 110 cm ~44 43

44 PPW-POLYPL AN-WERK ZEUGE GMBH Spiked wheel for Push cart (35) < Thereby your push cart don t leave marks on fresh layers, we supply you with the spiked wheel (35) made of stainless steel, complete with 180 spikes. The spiked wheel has an axle of 100 mm ~4 width for standard push carts. If your push cart has another width of the axle on the front wheel, we are able to produce you every size. Both spiked feet for the steady legs (35 F) of the push cart are included in the price. E

45 Applying of floor covering Floorsliding-Case (DGBM) It is possible to bring up even synthetic- or mineralbounded mortar, quartzstones or sand on concrete-, floor-pavement with the floorsliding-case. The mortar will be charged into the fillingshaft of the floorsliding-case and slides onto the concrete pavement. By pulling onto the bow of the floorsliding-case you can reach a homogeneous height and width of the coating. The coating height corresponds with the difference between floor and pulling ledge and can easily be changed. The floorsliding-case is made of sheet steel and has exchangeable skids. Width 45 cm 80 cm exchangeable ~18 ~32 skids order-no. (2245)< (2280)< (2245K)< weight 15.6 kg 22.5 kg 0.23 kg E E E

46 PPW-POLYPL AN-WERK ZEUGE GMBH FOR ECONOMICAL FILLING OF EXPANSION JOINTS IN FLOORS Joint filling machine (F 27)< with the joint filling machine (F27), sealing compounds (even two-component ones) can be quickly applied to floor joints. A metal nozzle guides the machine along the joint, and the machine must be pulled along at a steady speed. Filling the joint with sealing compound from the bottom to the top is possible. The tank (approx. 17 litres capacity) holds 10 litres sealing compound to which air is applied at 4 bars. If the viscosity of the sealing compound to be used is 14 Pa.s., the minimal efflux time for 10 litres at + 12 degrees C is around 20 minutes. 10 litres are sufficient for approx. 40 meters ~45 yards and a joint of 20 mm ~ 3 /4. Height of the mobile joint filling machine 110 cm ~43 5 /16, length 190 cm ~74 3 /4, weight 32 kg when empty. For cleaning, pipe scrapers (FE-41) and rubber scrapers (FE-39) are supplied with the machine. E (F 27) Sealing cord applicator for joints (1822) < with plastic hollow handle for extension With the sealing cord applicator the sealing material (round cord of PE or PU) is applied, thus precluding the risk of damage. The highadjustable guide wheel enables application of the round cord to DIN in the depths as required. (1822) E For wide joints a second wheel which is also supplied is fitted next to the first wheel (see photo). 46

47 Wooden Smoothing Tool < for filling compounds, with one straight and one rounded edge, of hard wood, total length 28 cm ~11 Thickn. 5 mm 10 mm 15 mm 20 mm 25 mm ~ 13 /64 13 /32 5 /8 3 /4 1 (1810) (1811) (1812) (1813) (1814) E Thickn. 30 mm 35 mm 40 mm 45 mm 50 mm ~1 3 / /8 1 5 /8 1 3 /4 2 (1815) (1816) (1817) (1818) (1819) E set (10 pieces) in a box (1820) E Primer Brush (1805) < with bottle for fluid single-component joint primers, bottle of PE, capacity 1 /8 ltr., brush exchangeable E 8.70 Primer Brush (1805 M)< as above but capacity of the bottle 1 /4 ltr. E (1805) Primer Brush (1805 T)< as above but capacity of the bottle 1 /2 ltr. E Spare Brush (1806) < E 4.50 Window Wiper of light metal Width 30 cm 40 cm ~ /4 (1723) (1724) E Spare Rubber for window wiper 30 cm 40 cm ~ /4 (1727 A) (1727 B) E (1724) 47

48 PPW-POLYPL AN-WERK ZEUGE GMBH Measuring Cylinder (PP) with Base < of polypropylene, slim shape, with mouth, transparent, unbreakable (101A) (101B) (101C) (101D) 10 ccm 25 ccm 50 ccm 100 ccm E (101E) (101F) (101G) 250 ccm 500 ccm 1000 ccm E (101) Measuring Cup (PP) with Handle < of polypropylene, with mouth, transparent raised scale, blue coloured (102A) (102B) (102C) (102D) 50 ccm 100 ccm 250 ccm 500 ccm E (102E) (102F) (102G) (102H) 1000 ccm 2000 ccm 3000 ccm 5000 ccm E (102) Polythene Funnel < (103D) (103E) (103F) (103G) top dia. 75 mm 100 mm 120 mm 150 mm ~ /4 6 bottom dia. 10 mm 13 mm 14 mm 16 mm ~ 13 /32 33 /64 9 /16 5 /8 E (103) (103H) (103I) (103K) (103L) top dia. 200 mm * 250 mm * 350 mm * 400 mm ~7 7 /8 9 7 / / /4 bottom dia. 21 mm 29 mm 31 mm 42 mm ~ 13 / / / /32 E Sieve Inserts (103 S) < for funnels marked *, 50 mm ~2 dia. E 3.80 (105) (103 S) Spraybottle < made of nonrigid PE, round, transparent complete with sprayplug capacity: 250 ml 500 ml 1000 ml 2000 ml (105 D) (105 E) (105 F) (105 G) E

49 Instant filter < made of paper, with glued-in fine filter gauze. Upper diameter approx. 160 mm ~6 5 /6. Smallest package sold = 250 filters- (1500 F) 280 µ } (1500 M) 400 µ (1500 G) 1000 µ je E Stück for ,50 filters Funnel Jug < made of durable plastic material with flexible spout Capacity 0.5-ltr. (330) E 9,90 Capacity 1.0-ltr. (331) E Capacity 2.0-ltr. (332) E (1500 F) Funnel Jug < made of tin-plate, leak-proof Capacity 1.0-ltr. (321) E Capacity 2.0-ltr. (322) E POLYPLAN-Dispenser unbreakable and stable polythene (PE) material This dispenser is suitable for quick and exact filling of hardeners and accelerators. Good application for mass fillings in particular because of its constant quantities. By shifting the marking (A) the quantity (B) to be filled can be adjusted easily. The measuring tube (C) is filling by pressing the bottle (F). On release the excess quantity flows back into the bottle so that the desired quantity of fluid remains in the measuring tube (C). This can then be poured out. (331) (321) A B C D F POLYPLAN-Dispenser (100) < including a 2.5 ltr. PE-bottle for filling up to 100 ccm POLYPLAN-Dispenser (25) < including a 1 ltr. PE-bottle for filling up to 25 ccm E E

50 PPW-POLYPL AN-WERK ZEUGE GMBH Volume-Mixing-Cup < Perfectly made for mixing and storing of lacquers. The Volume-Mixing-Cup consists of an outer receptacle with cover, in which a transparent inner receptacle will be clicked. There are volume-scales (1:1, 2:1, 3:1, 4:1, 5:1 and 10:1) and each time 10% and 20% addition of accelerator solvent-resistant imprinted on the outer receptacle. The inner receptacle can be easily changed after mixing the lacquers, so you don t need to clean the outer receptacle and can use it several times. For a short time of storing the lacquers the outer receptacle can be locked with the cover, so that the laquers don t desiccate. Available in 2 sizes: Outer receptacle + Cover 920 ml (208 M) E 9.70 / set 10 Inner receptacles for (208 M) (208 ME) E 4.80 / 10 pieces Outer receptacle + Cover 1850 ml (208 G) E / set 10 Inner receptacles for (208 G) (208 GE) E 7.70 / 10 pieces Wetcoating-Thickness-Gauge (2300) made of aluminium By putting the Wetcoating-Thickness-Gauge on a ground you can exactly measure the height of wet coatings. Measuring accuracy µm. The scales are solvent-resistant eloxed. E / piece Prices subject to be changed without notice! 50

51 Barrel Winged Mixer (3720) fits any large plug hole of 55 mm ~2 3 /16 diameter. The wings open automatically by centrifugal force Total diameter: 220 mm ~8 5 /8 Total length: approx mm ~41 3 /8 Shaft diameter 10 mm ~ 13 /32 E Can Stirrer (1804) < to stir two-component putties and resins in cans. To be clamped into a slowspeed drilling machine Total length: 580 mm ~22 7 /8 E (3720) Cartridge Stirrer (1803) < to stir two-component putties in cartridges. To be clamped into a slow-speed drilling machine Total length: approx. 500 mm ~20 E (1804) Mixer Propeller < particularly suitable to mix two-component plastics and foams, etc. suitable for any drilling machine. Total length approx. 350 mm Diameter approx. 45 mm 70 mm 85 mm ~1 3 /4 2 3 /4 3 3 /8 Shaft diameter 6 mm 6 mm 8 mm ~ 1 /4 1 /4 5 /16 (3861) (3862) (3863) E E E Helical Stirrer < the helical stirrer is suitable for mixing and stirring of filling material, bonding agents, plasters adhesives, fine and coarse plastics Type Compound Dia. Length Shaft dia. quantity mm / mm / mm / (3770) up to 5 kg 70 / ~2 3 /4 400 / ~15 3 /4 8 / ~ 5 /16 E (3771) up to 10 kg 90 / ~3 35 / / ~15 3 /4 8 / ~ 5 /16 E (3775) up to 25 kg 135 / ~5 5 / / ~24 10 / ~ 13 /32 E (3776) up to 50 kg 165 / ~6 1 /2 650 / ~25 5 /8 12 / ~ 1 /2 E (1803) ( ) ( ) Circular Stirrer < the circular stirrer is suitable for mixing and stirring of epoxy resins, two-component materials, plastics, filling materials, bonding agents, adhesives, pastes Type Compound Dia. Length Shaft dia. quantity mm / mm / mm / (3780) up to 15 kg 85 / ~3 3 /8 400 / ~15 3 /4 8 / ~ 5 /16 E (3781) up to 25 kg 115 / ~4 1 /2 600 / ~24 10 / ~ 13 /32 E (3783) up to 50 kg 165 / ~6 1 /2 650 / ~25 5 /8 12 / ~ 1 /2 E Force Stirrer (3763) especially for mixing and stirring of two-component resins such as epoxy, polyester and acrylic resins Type Compound Dia. Length Shaft dia. quantity mm / mm / mm / (3763) up to 10 kg 85 / ~3 3 /8 430 / ~17 10 / ~ 13 /32 E Paddle Mixer (3791) < 80 mm ~3 1 /8 diameter, for liquid plastics. Because of the double blades the inclusion of air will be reduced. Up to 10 kg compound quantity appropriate, with hexagon-shaft dia. 8 mm ~ 5 /16, length overall 400 mm ~15 3 /4, galvanized E ( ) (3763) (3791) 51

52 PPW-POLYPL AN-WERK ZEUGE GMBH Evacuation Cock < to evacuate viscid liquids out of barrels, containers etc., with different pipe-g-thread-sizes : of grey cast iron 3 /4 1 1 / (118 A) (118 D) (118 E) (118 G) (118 H) E of red bronze for aggressive media, applicable for food. 3 /4 1 1 / (218 A) (218 D) (218 E) (218 G) (218 H) E Rotguß Grauguß Stop-Cock (119 N) < utterly tight seal, strong cock housing Thread end 3 /4 G pipe thread E (119 N) One-way Barrel Cock (117) < of solvent-resistant plastics, particularly suitable for fluid resins Thread end 3 /4 G pipe thread E 2.60 (117) Barrel Tip-Support (3711) for lifting, transportation, storing and filling of 200 ltr. barrels, with 2 guide and 2 load rollers. The barrel resting on 4 rollers can be turned into pour-position easily, without lever bar. Width x Length: 680 x 800 mm ~27 1 /8 x 32, weight 14 kg E Lever Bar (3712) fitting the barrel tip-support, with plastic handle and hook Length: 1480 mm, ~58 1 /4 Weight: 3 kg E (3712) (3711) 52

53 Barrel Plug Key (389) forged steel, approx. 550 mm long ~22, with squares of 14, 22, 24 and 28 mm ( 5 /8, 7 /8, 15 /16 and 11 /8 ), with flats for slit plugs and American plugs Tri-Sure E (389) Barrel Pump of Sheet Steel (271) pump length 100 cm ~40, inside width approx. 30 mm ~1 3 /16, overhang of discharge pipe approx. 30 cm ~12, box containing 2 pieces price per piece E Extra charge when ordering only 1 off E 3.00 (271) Barrel Cart (3713) with supporting wheel The barrel is held in place by a hook which can be moved freely. Solid rubber wheels with roller bearings. Width x height: 660 x 1600 mm, ~26 x 63 E (3713) 53

54 PPW-POLYPL AN-WERK ZEUGE GMBH (74) Scissor of Cast Steel (74) forged, with bent-up eyes, varnished black, fine-polished blades, high screw Width E Scissor of Stainless Steel (73) the moulded-on solvent-resistant plastic eyes are adapted to the workers hands and prevent marks from their fingers. Heavy design Total length 260 mm ~10 1 /4 E (73) Pocket Knife first quality, hardened steel, blade ground by hand, wooden handle Bent blade (38) E Straight blade (39) E (39) (38) Universal Knife (52) with replaceable blades in the metal handle E 3.90 (52) (52 E) Spare Blades (52 E) trapezoidal, straight blade 10 blades = 1 package package E 2.60 Mat Knife (48) stainless steel with beech wood handle, blade 7 long, total length 31 cm ~12 E (48) Tool Knife (49) cast steel with beech wood handle, blade 5 long, total length 26 cm ~10 1 /4 E (49) (852) Window Scraper (852) with hollow plastic handle and holder for 100 mm ~4 wide special scraper blades. These blades are blunt on one side for crude scraping off and ground on the other side for fine cleaning E Spare blades (853 E) 10 blades = 1 package package E

55 Painters Spatula (2) machine-ground, white wooden handle with blade, perfect junction by rivets Width 2 cm 3 cm 4 cm 5 cm 6 cm 8 cm 10 cm 12 cm ~ 3 /4 1 3 / / /8 3 1 / /4 E (2) Scaling Spatula (7) short, stiff, one-side ground blade, flat, oval white wooden handle, riveted Width of blade 5 cm 7 cm 10 cm ~2 2 3 /4 4 E Surface Spatula (64) 100 mm ~4 steel blade, 50 mm ~2 wooden back- Width 14 cm 16 cm 20 cm 25 cm 30 cm 40 cm 50 cm ~5 1 /2 6 5 / /8 9 7 / / / /4 E (7) Japan Smoothing Spatula (65) with aluminium back, absolutely solvent-resistant, no rivets, 1 set = 1 piece of each width Width 5 cm 8 cm 10.5 cm 12 cm /8 4 1 /8 4 3 /4 set E 7.30 Smoothing Spatula (67) < of plastics, flexible, solvent-resistant, size of blade 120 x 80 mm ~4 3 /4 x 3 1 /8, 1 mm ~ 3 /64 thick E 0.30 (64) (65) (67) Triangular Scraper (131) with screwed blade of crucible cast steel, total length 25 cm ~9 7 /8, polished wood handle about 11 cm long ~4 11 /32, width of blade 6 cm ~2 3 /8 E Spare blades (131E) E 3.00 Paint Scraper (262) super blade of COROMANT hard metal, blade exchangeable, blade width 70 mm ~2 3 /4, both sides to be utilized, especially strong type with plastic knob to apply increased pressure, overall length 300 mm ~11 13 /16 E Spare Blade (262 E) of hard metal, both sides to be utilized, width 70 mm ~2 3 /4 E (131) (262) (262 E) Universal Paint Scraper (261) blade of COROMANT hard metal, blade width 50 mm ~2, blade exchangeable, both sides to be utilized. Handle and grip same as (260), overall length 250 mm ~10 E Spare Blade (261 E) of hard metal, both sides to be utilized, width 50 mm ~2 E Paint Scraper (260) blade of COROMANT hard metal, triangular, side length 24 mm ~ 15 /16, plastic grip with light metal handle, overall length 250 mm ~10 E Spare Blade (260 E) of hard metal, 3 sides to be utilized E (261) (261 E) (260) (260 E) 55

56 PPW-POLYPL AN-WERK ZEUGE GMBH Coarse Dust Filter Mask (8500) < for protection against troublesome coarse dusts, flame-resistant, self-extinguishing, green Weight 10 g each E 0.50 Small box = 50 pieces (8500) Fine Dust Filter Mask (8710)< for protection against troublesome fine dusts, flame-resistant, self-extinguishing, with two elastic holding bands Weight 11 g each E 1.65 (8710) Fine Dust Filter Mask P1 (8710 E) < for protection against troublesome fine dusts flame-resistant, selfextinguishing, with two elastic holding bands Weight 11 g - each E 2.50 (8710 E) Fine Dust Filter Mask (8979)< with exhalation valve for easy breathing protection against very troublesome fine dusts, white with two elastic holding bands Weight 18 g each E 5.60 (8979) Fine Dust Odour Mask (9383)< with exhalation valve for easy breathing protection against very troublesome fine dusts and unpleasant organic odours, solvent vapours, black with two elastic holding bands Weight 20 g each E 9.45 (9383) (8825) Mask to protect against fine dust particles P2 (8825) < with exhalation valve against fine dusts hazardous to health (asbestos, smoke, fog) admitted under DIN FHM-P2 Weight 32 g each E

57 Full-Vision Gas Mask (8721) with panoramic window of Polycarbonat with large field of vision. By means of the built-in inner mask the air taken in passes the window in such a way that it will not mist up. Inhalation valve with connector, two exhalation valves laterally arranged and a voice diaphragm to allow a good communication. Its universal size fits any head form. All metal parts of NIROSTA (stainless steel). Knuckle thread connection according to EN fitting any filter inserts. Weight of mask 580 g (8721) Accessories: Screw-on gas protection screw filter A (8566) for any type of solvent vapours, protective grade A2 Screw-on gas protection filter A (8580) incorporating fine-dust filter for any type of solvent vapours and fine dusts, protection grade A2 + P2 Screw-on gas protection filter A (8581) incorporating fine-dust filter for any type of solvent vapours and fine dusts, protection grade A2 + P3 Filter against particles hazardous to health (8530) protection grade P3 Attachment Foil (8720F) self-sealing to window shield (8530) (8566) (8580) Spare parts: Spare window shield of Polycarbonat (8721 P) Paint Sprayers Mask (8650) with gas protection filter insert. The half-mask consists of a soft mask body of Perbunan, two exhalation valves with ante chamber to prevent dirt accumulation from the valves, with filter insert of shock-proof plastic material. Unless ordered differently, the mask will be supplied together with filter (8523). (8650) Weight of complete mask 275 g Accessories: Gas protection filter insert (8523) incorporating fine-dust filter for any type of solvent vapours and fine dusts, protection grade A1 + P2 Filter against fine dust (8524) metallic vapour, protection grade P2 Filter against particles hazardous to health (8525) protection grade P3 Coarse dust filter of gauze (8502) box containing 20 pieces Box (8720 T) Carrying Box (8720 T) of grey plastic material, suitable for full-vision gas mask (8721) 57

58 PPW-POLYPL AN-WERK ZEUGE GMBH Protective Visor (8631) the visor is used whenever there is a danger of caustic liquids being splashed into the face. The visor can be raised to any desired position. Quickly interchangeable plastic screen secured by means of three press studs. An adjustable elastic strap permits quick attachment of the visor to the protective helmet. E Replacement screen (8632) E 7.90 (8631) Protective Helmet (8630) made from PE plastic material to DIN 4840, turned up edge to catch rain water, adjustable ventilation, internal strap support and all-round leather sweat band. Adjustable wearing height, quick size adjustment ensures firm fitting of helmet, even when bending down. Head sizes: Weight: approx. 335 g (8630) E 9.00 (8636) Ear Protection (8636) lightweight design, weight approx. 130 g. Flat ear pieces and a wide strap ensure comfortable wearing. The ear pieces are pivoted and can be adjusted to any required height thus fitting any shape of head E Ear Protection (8636 B) as above but with neck-strap E (8125) Eye Rinsing Bottle (8125) pneumatic to rinse eyes immediately after burns by acids, lyes, etc E Wall Holder (8125 H) for eyes rinsing bottle, made of coated wire E

59 Protection Eyeglasses (8620) of plastic material, excellent fit, wide field of vision, side protection, exchangeable glasses E 9.35 Replacement glasses (8621) pair E 2.90 Panoramic Protection Eyeglasses (8615) extremely light-weight, soft elastomeric material for those parts in direct contact with the face, mar-proof glasses of plastic material, solvent resistant, weight 59 g E Replacement glasses (8616) pair E 6.80 Hood (8203) with collar of TYVEK, with elastic band, protects head and neck against dirt and dust E 1.95 Oversleeves (8204) of TYVEK with elastic band pair E 2.15 (8620) Overshoes (8202) of TYVEK, high design for lacing up pair E 3.90 (8615) TYVEK-Overall (8200) white TYVEK is a blend of 100 % polythene fibers and cellulose. Therefore, the overall has excellent qualities: Very light, smooth and flexible, yet enormously hard-wearing, tearresistant in both directions, not transparent, chemicalresistant, flame-resistant (+125 degrees C) and water-repellent. The overall has a cowl and is fitted with zip fastener, with elastic at the back, and back pocket. Größe 1 = 42/44 standard size, S Größe 2 = 46/48 standard size, M Größe 3 = 50/52 standard size, L Größe 4 = 54/56 standard size, XL Größe 5 = 58/60 standard size, XXL 3 % discount allowed on orders of 25 pcs. of one size 5 % discount allowed on orders of 100 pcs. of one size Plastic Apron (8230) resistant to oil and petrol, 100 x 120 cm ~40 x 48 (8200) (8230) 59

60 PPW-POLYPL AN-WERK ZEUGE GMBH Rubber Gloves (127) special rough finish, easily fitted sizes per pair E 3.90 (127) NITRIL-Gloves (3400) with knitting band, back of the hand not coated per pair E 3.05 One-way Gloves of polyethylene foil (129) 1 pack = 100 pieces E 2.55 (3400) Under Gloves thin cotton for wearing under rubber gloves, 5 fingers (124 F) medium per pair E 0.65* (124 M) large per pair E 0.65* Twill Gloves (123) thick cotton quality, 5 fingers per pair E 0.85* (129) Universal Gloves (125) 5 fingers, split leather, pulse and knuckle protection, textile sleeve and back of the hand per pair E 1.70* (124 F) Universal Gloves (126) 5 fingers, solid leather, pulse and knuckle protection, textile sleeve and back of the hand per pair E 3.00* * price subject to change without notice (123) (125) (126) 60

61 Flexible Knee Pads (4035) made of polythene with inwrought, an antistatic cellular rubber-profile, outside slip resistant profile-surface and rubber strap 2 pcs. = 1 pair E (4035) Knee Pads (4038) < hard plastic cap, cellulose caoutchouc pads and stretch straps with velcro fastenings 2 pcs. = 1 pair E Knee Pads (4033)< box-form, made of integral soft foam to prevent the absorption of liquids, and the knees remain dry. They are designed according to orthopedic cognition and provided with a wear-resistant rubber strap. 2 pcs. = 1 pair E (4038) (4033) Knee Pads (4033 S)< as above, but cup-shaped round 2 pcs. = 1 pair E Knee Pads with Folds (4034)< as above, with 4 folds of plastic, which are lying around the knee and prevent the penetration of material 2 pcs. = 1 pair E (4033 S) Straps for Knee Pads (4034 K) length: 315 mm ~12 3 /8 Straps for Knee Pads (4034 L) length: 420 mm ~16 9 /16 E 1.00 E 1.35 (4034) 61

62 PPW-POLYPL AN-WERK ZEUGE GMBH ZEC-Grinding Disc ZEC grinding disc is a strong vulcanized fibre disc with abrasive grains coated one upon another in several layers. The ZEC disc is used on angle hand-grinders with elastic sole plate of rubber which obtain a working speed of 6500 or 8500 rev./min. Application dia. granulation (115 SC) concrete/stone 115 mm ~4 1 /2 E 6.90 (178 SC) (127 SC) concrete/stone 127 mm ~5 E 7.80 (115 T) (178 SC) concrete/stone 178 mm ~7 E 9.20 Sole Plate elastic fitting ZEC grinding discs and fibre discs with tension screw M14 (178) (115 T) (120 T) (178 T) E (115) Fibre Disc (115) with corundum, flat, full resin compound, 115 mm ~4 1 /2 dia., with a 22 mm ~ 7 /8 diameter hole and 4 slots granulation E (178) with corundum, as above, but 178 mm ~7 diameter and 4 slots granulation E Water-Proof Latex Abrasive Paper (230) strewn with silicon carbide in sheets of 230 x 280 mm ~9 1 /16 x 11 (230) granulation E granulation E Abrasive Paper (237) low-priced quality, in rolls 110 mm ~4 5 /16 wide, 1 roll = 50 m ~55 yards granulation E per 100 m ~110 yards (237) 62

63 N E T - P R I C E S The prices on this catalogue-page are net-prices! It is only possible to get quantity-rebates! Tesa Masking Tape (4438) masking tape for plastering. Protects delicate surfaces from plastering material and damage. The masking tape is smooth strong, abrasive-resistant and not sensitive to humidity, ultraviolet radiation and mechanical wear. The tape is easily unwound and ensures excellent adhesion to smooth wood, metal, plastics and ceramics. Tesa masking tape (4438) will not leave any marks when removed within two months (provided temperature is above + 5 degrees C). Quality (4438) 1 roll = 50 m ~55 yards Width 19 mm 30 mm 38 mm 50 mm ~ 3 /4 1 3 / /2 2 Pack of 16 rolls 10 rolls 8 rolls 6 rolls price per roll E (4304) brown (4438) blue (4319) yellow Quality (4319) 1 roll = 50 m ~55 yards elastic standard masking tape, low-priced Width 19 mm 25 mm 30 mm 38 mm 50 mm ~ 3 / / /2 2 Pack of 16 rolls 12 rolls 10 rolls 8 rolls 6 rolls price per roll E Quality (4304) 1 roll = 50 m ~55 yards fine crepe masking tape, moisture-proof, impregnated, abrasive-resistant, chamois Width 19 mm 25 mm 30 mm 38 mm 50-mm ~ 3 / / /2 2 Pack of 16 rolls 12 rolls 10 rolls 8 rolls 6 rolls price per roll E (4124) Quality (4124) 1 roll = 66 m ~73 yards PVC foil, adhesive tape, colour brown Width 50 mm ~2 Pack of 6 rolls price per roll E 2.75 (4369) 5 % quantity rebate for 1 package 10 % quantity rebate for 6 packages easy cover (4369) folded PE-coverfoil with pressure sensitive adhesive tape from a roll. Ideal masking-tape for clear-cut line, large surface covering and protection on one single operation. Secure protection enable a fast and unerring working. Through the embossed PE-coverfoil the colour does not drop. Easily and unproblematicly removable without residues of adhesive. size of roll: rolls/ price per Length :Width pack roll with blue adhesive cloth tape ( ) 20 m : 550 mm 60 E 2.30 for in- and outside, stable towards 22 y : 21 5 /8 UV-radiation till 2 weeks ( ) 20 m : 1100 mm 30 E y : 43 5 /16 ( ) 17 m : 1800 mm 30 E y : 72 Masking- and building protective tape (4370) red special adhesive cloth tape for protection of valuable surfaces, especially for a longer paste over outside on smooth and uneven grounds. Stable towards UV-radiation till 8 weeks size of roll: rolls/ price per Length :Width pack roll ( ) 25 m : 25 mm 72 E y : 1 ( ) 25 m : 50 mm 36 E y : 2 10 % quantity-rebate for 1 package (4370) 63

64 PPW-POLYPL AN-WERK ZEUGE GMBH PE-Bucket (19) natural white, non-abrasive, therefore not colorific, stable design, 20 liter capacity E PE-Barrel with two carrying handles, made of natural white Polyethylen, conical shape (45) 45 liter-capacity E (75) 75 liter-capacity E

65 Plastic Buckets (PE) standard 5 litres (5) E 1.90 standard 10 litres (10) E 2.20 with lid for transportation 5 litres (5 D) E 2.60 with lid for transportation 10 litres (10 D) E 3.25 flat-shaped, strong bucket 12 litres (12) E 1.50 square-shaped bucket for 14 litres (12 E) E 6.50 rollers up to 30 cm ~12 (10) (12) Plastic Paint Buckets (14) PE, with integrated scraping surface, 14 litres, size 32 x 25 cm ~12 5 /8 x 7 /8 E 5.90 Plastic Dish in PE dia. cm ~7 7 /8 9 1 / / / /4 (20) (24) (28) (32) (36) (40) E (12 E) (14) Pot with handle (210) 22 cm ~8 5 /8 diameter, PE, easy to manage E 2.40 Paint trough (70) for large-sized paint rollers, made from black plastic material, 65 cm ~25 5 /8 long, 35 cm ~13 3 /4 wide, 30 cm ~12 high (inside measurements), capacity 65 litres Mixing jug (500)< E with scale, 500 ccm, made of polypropylene, minimum not rigid, transparent selling quantities: resistant to solvents each E 0.60 for 10 jugs each E 0.55 for 100 jugs Wooden Scraper (1487) < with rounded corners, size 150 x 18 mm ~6 x 23 /32, 2 mm ~ 5 /16 thick per 100 each E 4.80 (20 40) (70) (210) Pasteboard Cups PE-coated 250 ccm, 59 mm high (250) 100 mm ~3 5 /16 top dia. 1 box = 2000 cups 80 mm ~3 1 /8 base dia. per 100 each E (1487) 480 ccm, 85 mm hoch (480) 103 mm ~4 1 /16 top dia. 1 box = 1000 cups 82 mm ~3 1 /4 base dia. per 100 each E ccm, 120 mm high (990) 130 mm ~5 1 /8 top dia. 1 box = 500 cups 105 mm ~4 1 /8 base dia. solid design per 100 each E (500) (480) (250) (990) Paint trough (22) PE, with integrated scraping surface, size 18 x 16 cm ~7 1 /8 x 6 5 /16 E 0.85 Beech Stirring Sticks < Size Length Width Thickness per 100 each K 230 mm 24 mm ~ 15 /16 ~4 mm ~ 5 /32 (1401) E G 300 mm 27 mm ~1 1 /16 ~4 mm ~ 5 /32 (1402) E E 370 mm 35 mm ~1 3 /8 ~6 mm ~ 19 /32 (1403) E H 450 mm 35 mm ~1 3 /8 ~6 mm ~ 19 /32 (1404) E (22) (1401) (1402) (1403) (1404) 65

66 Terms of Sale and Delivery I. Conclusion and subject of the contract For our deliveries and other legal transactions, the terms and detailed below shall apply exclusively. Any other verbal and telegraphic arrangements, amendments, promises and collateral agreements shall be invalid unless by us in writing. Purchase and payment terms stipulated by the Buyer shall not be accepted by us. The Buyer shall accept our Terms of Sale and Delivery even if they deviate from his usual purchase and payment terms. Any objections raised to order confirmations must be submitted in writing without delay, at the latest within one week. The legal inefficacy of individual provisions shall not render the entire contract invalid. II. Offers All offers made shall be without engagement unless expressly stated to the contrary, in which case they shall be binding for one month only calculated from the date of the offer, unless another period is specifically indicated. Obvious errors, spelling mistakes and miscalculations shall be without commitment on our part. All particulars, such as dimensions, weights, illustrations, descriptions, assembly drawings and illustrations in sample catalogues, price lists and other reference materials shall be approximate only but determined as closely as possible, and shall not be binding on our part. III. Prices All prices are quoted ex works excluding Value Added Tax. Confirmed prices shall apply only if the confirmed quantities are bought. In the event of price increases occuring between the date of the order confirmation and the supply of the goods, we shall be entitled to adjust the prices accordingly. IV. Delivery Delivery shall be for account and risk of the Buyer, even if carriage-free delivery has been agreed. If free delivery has been agreed, the risk shall pass to the Buyer as soon as the vehicle arrives at ground level at the forwarding address, or at the point nearest to this address that can be reasonably reached by the vehicle. Selection of the transport route and means of the transport shall rest with us. Partial deliveries shall be admissible and shall be considered as independent deliveries. If the Buyer does not accept the goods in time, or if he fails to observe the call dates, we shall be entitled to effect the deliveries due, either in full or in part, or to put the goods into storage and invoice as delivered, to rescind, either in full or in part, or finally to demand compensation on the grounds of nonfulfillment. Disruptions caused by fire, strikes, lockouts, shut-downs, official measures, lacking supplies and force majeure which may prevent or impair the deliveries, shall entitle us, at our option, to rescind, either in full or in part or to postpone the deliveries accordingly without being liable for damages. Non-observance of delivery times does not release the Buyer from his obligation to accept the goods. For any damages due to a delay in at cost price. Returning packaging material shall be accepted and refunded only if specifically agreed upon. Insurance covering damage in transit, loss in transit and breakage shall only be taken out if expressly requested by the Buyer and shall be charged to him. V. Warranty Any claims on the scope, amount, weight, dimensions, and kind of the goods must be made immediately but no later than three days after arrival of and prior to use of the goods. Claims concerning partial deliveries shall not entitle the Buyer to refuse acceptance of the entire delivery. Notifications of defects must be made in detail and in writing and must be received by us within seven days of arrival of the goods. Claims in respect of hidden defects must be made immediately on discovery of the defect, at the latest, however, within two months after receipt of goods. If defective goods have been delivered, we shall be entitled, at our option, to reduce the price, make good the defect or supply faultless replacement. We shall be entitled to supply replacement even if this cannot be effected immediately. Any replacement shall be supplied at the earliest possible date. Any further claims by the Buyer on whatever legal grounds, especially with regard to redhibition and indemnification, shall be excluded. We shall be under no obligations to acquire replacements from other sources. No warranty whatsoever shall apply of the processing or use of the goods has already been commenced, or if the Buyer himself or any third party has carried out, or tried to carry out, repairs of our goods. The same shall apply to any goods which have been sold by the Buyer either before or after claims have been made. In the case of manufacturing defects our warranty shall be limited to the warranty given by our suppliers. By negotiating a claim we shall not be considered as waiving our objections to the existence of a defect, to the obligations for the supply of replacement, or to the time limit and sufficiency of the claim. VI. Return of goods Goods delivered by us shall only be taken if agreement to this effect has been made and shall be returned in immaculate condition, carriage paid. Credits for returned goods shall be subject to a 10% deduction for costs incurrent. Returns to specially made goods, or goods procured at the specific request of the customer, shall be excluded. For returned goods with a net value less than EUR 50.-, no credit-notes will be made. VII. Payment Unless agreed otherwise, our deliveries shall be paid for at once, at the latest 30 days after date of the invoice. All payments shall be made free of charge for us. Payments effected within 10 days of receipt of invoice shall be subject to a discount of 2 per cent, provided, however, all financial commitments have been met in full, including those for earlier deliveries. The discount shall be calculated based on the net invoice amount, after deduction of rebates, freight charges etc. Once payment of an invoice has become due i.e. at the latest 30 days from the invoice date, interest will be charged at a rate of 3 per cent above the base rate of the European Centralbank, not excluding the right to make further claims for default. The day of receipt of any payment shall be the day on which our account has been credited with the respective amount. Bills of exchange and cheques shall only be accepted subject to being honoured. Acceptance of bills of exchange shall be as security only, and shall not be considered as respite for payment. If our bankers decline to discount a bill of exchange, then payment in cash must be made immediately. Discounting and collecting charges shall be for Buyer s account. Liability for payment shall persist even if the Buyer has submitted claims, in particular in respect of defects. The warranty detailed under Paragraph V shall be given on the understanding that the Buyer has effected the payments due. The right to make setoffs and claiming a lien on goods shall be excluded. Vlll. Retention of Title All goods supplied by us under a delivery contract shall remain our property until payment in full has been made, or until cheques or bills of exchange have been honoured. In the case of a current account the retention of title shall be considered as security for our claim of the balance. The Buyer shall be entitled to legally sell the goods supplied and the goods manufactured from these. He shall be obliged to impose our condition of retention of title on his customers. Without our written consent the Buyer shall not be entitled to assign, pledge or transfer the title as security. When selling the goods supplied by us, the Buyer shall assign at that moment all claims against his customers, including ancillary rights and securities out of sale until all payments to us have been made in full, and this assignment shall be accepted by us. If the goods are taken back on the basis of our retention of title or any other reason, the Buyer shall be obliged to return the goods to us free of charge and shall be liable for any undervalue. We shall be entitled to collect the goods when enforcing our right or retention of title. IX. Place of performance and place of jurisdiction Place of performance for deliveries shall be the place of the goods. Place of performance for all obligations on the Buyer s part shall be the location of our firm. Place of jurisdiction shall be the court competent for the location of our firm. This shall also apply to claims being filed by judgement note. The law of the Federal Republic of Germany shall apply. The provisions of the Hague Convention of 1964 on purchases and purchase contracts shall be excluded. X. Validity If one instruction will be invalid, the validity of the other instructions won t be touched herefrom. 3/02 PPW-POLYPLAN-WERKZEUGE GMBH Hamburg Germany 66

67 Testing and controlling of cracks and changes in surface are important points in this time. We deliver measuring devices and tools for: testing of cracks and building alteractions contolling of varnishes and coatings of surfaces up to complete equipment program of tools for sealing and reconstruction of buildings Please ask for our new catalogue or visit us on our homepage: PPW-POLYPLAN-WERKZEUGE GmbH P.O. Box D Hamburg Phone: (0) 40/ Fax: (0) 40/ ppw@polyplan.com Internet: INJEKTIONS- PROGR AMM 67