Adjusting instructions and illustrated parts list

CATALOG NO. 29M Adjusting instructions and iustrated parts ist Fifth Edition CLASSES 5 6 200 56300 56400 56500 56700,.., u 56900 Serie s 5000 0 - Advanced, high speed, f at bed machines Finest Quaity

CATALOG NO. 29 M ADJUSTING INSTRUCTIONS AND ILLUSTRATED PARTS LIST FOR SERIES 50000 ADVANCED, HIGH SPEED FLAT BED MACHINES STYLES 56200 H 56200 K 56200 L 56200 R 56200 S 56200 W 56300 E 56300 F 56300 G 56300 H 56300 M 56300 N 56300 R 56300 U 56300 W 56300 X 56300 AH 56300 AL 56400 D 56400 P 56400 R 56400 S 56400 T 56400 W 56400 X 56500 A 56500 B 56500 C 56500 J 56500 R 56500 U 56700 J 56900 H 56900 J 56900 P 56900 R Fifth Edition 965, 982 By Union Specia Corporation Rights Reserved in A Countries Printed in U.S.A. March, 982 2

IDENTIFICATION OF MACHINES Each UNION SPECIAL machine carries a Stye number, which on these Casses of machines, is stamped into the stye pate affixed to the right front of machine. The seria number is stamped in the casting at the right rear base of machine. CLASS DESCRIPTION (56200) Advanced high speed, ow or medium throw, fat bed machines. Singe neede, one ooper, encosed automatic ubricating system. Maximum reconmended speed 6500 R.P.M. Maximum work space to right of neede bar 8 /4 inches (209.6mm). MACHINE STYLES 56200 H Low throw machine. Typica appication - For misceaneous seaming operations on ight to medium weight wash and wear materias where chaining and a short stitch are required. Seam specification 40 SSa-. Type 0 GS neede. 56200 K Low throw machine. Typica appication - For binding aprons and dresses made with ight to medium weight materias. Seam specification 40 BSc-. Type 06 GLS neede. Uses cut edge binding 3/4, 7/8,, /8, /4 inch (9.0, 22.2, 25.4, 28.6, 3.8nm) wide and produces a 7/32, /4, 9/32, /32, 3/32 inch (5.6, 6.4, 7., 8.7, 0.3mm) finish, respectivey. #56200 L Medium throw machine. Typica appication - For binding mattress ticks made with medium to medium heavy weight materias. Seam specification 40 BSa-. Type 26 GS neede. Uses sevage edge binding 5/8, 3/4, 7/8 inch (5.9, 9.0, 22.2mm) wide and produces a 5/6, 3/8, 7/6 inch (7.9, 9.5,.mm) finish, respectivey. *56200 R Low throw machine. Typica appication - For joining shouders of shirts in one operation made with ight to medium weight materias. Seam specification 40 LSe-. Type 06 GLS neede. 56200 S Low throw machine. Typica appication - For misceaneous operations on woven materias, knitted drawer bands, knitted shirt fronts made with ight to medium weight materias. Seam specification 40 SSa-. Type 08 GHS neede. 56200 W Medium throw machine. Typica appication - For seaming cotton fanne and eather pam goves. Seam specification 40 SSa-. Type 28 GAS neede. CLASS DESCRIPTION (56300) Advanced high speed, medium or high throw, fat bed machines. Singe neede, one ooper, encosed automatic ubricating system. Maximum work space to right of neede bar 8 /4 inches (209.6mm). #Discontinued - Repaced by Stye 56300 M. *Discontinued - In most instances, repacement parts are avaiabe. 3

CLASS DESCRIPTION (56300 Continued) MACHINE STYLES 56300 E Medium throw machine, equipped with thumbscrew adjustabe frame neede thread eyeet, automatic chain cutter and pressure reease attachment. Typica appication - For seaming trousers and coats made with medium to medium heavy weight materias. Seam specification 40 SSa-. Type 28 GBS neede. Maximum reconmended speed 6500 R.P.M. 56300 F Medium throw machine, equipped with thumbscrew adjustabe frame neede thread eyeet and a feeding presser foot. Typica appication - For seaming trousers and coats made with medium to medium heavy weight durabe press materias. Seam specification 40 SSa-. Type 28 GBS neede. Maximum recommended speed 6500 R.P.M. 56300 G Medium throw machine, equipped with thumbscrew adjustabe frame neede thread eyeet. Typica appication - For seaming trousers, coats and simiar garments, made of medium to medium heavy weight materias. Seam specification 40 SSa-. Type 28 GBS neede. Maximum recommended speed 6500 R.P.M. 56300 H High throw machine. Typica appication - For seaming couch covers, with or without rope wet made with medium heavy to heavy weight materias. Wet guided to the eft of neede. Seam specification 40 SSa- or 40 SSk- modified. Type 43 GS neede. Maximum recommended speed 6000 R.P.M. 56300 M High throw machine. Typica appication - For binding mattress ticks made with medium heavy to heavy weight materias. Seam specification 40 BSa-. Type 26 GS neede. Uses sevage edge binding 5/8, 3/4 and 7/8 inch (5.8, 9.0 and 22.2mm) wide, and produces a 5/6, 3/8 and 7/6 inch (7.9, 9.5 and.mm) finish respectivey. Maximum recommended speed 6000 R.P.M. 56300 N Medium throw machine, equipped with thumbscrew adjustabe frame neede thread eyeet and top-grip feed mechanism. Typica appication - For edge seaming operations on trousers, sacks, dress pants, jackets made of ight to medium weight durabe press materias. Maximum seam width is inch (25.4mm) necessitated by the top-grip-feed mechanism. Seam specification 40 SSa-. Type 28 GBS neede. Maximum recommended speed 6500 R.P.M. 56300 R Medium throw machine, equipped with thumbscrew adjustabe frame neede thread eyeet and feeding presser foot. Typica appication - For seaming side and inseams on trousers, back and side seams on coats, seeve seams on jackets, coats made with medium to medium heavy weight materias. Seam specification 40 SSa-. Type 28 GBS neede. Maximum recommended speed 6500 R.P.M. *56300 U Medium throw machine, equipped with thumbscrew adjustabe frame neede thread eyeet and top-grip-feed mechanism. Typica appication - For edge seaming operations on trousers, sacks, dress pants, jackets and simiar garments made of ight to medium weight materias. Maximum seam width is inch (25.4mm) necessitated by the top-grip-feed mechanism. Seam specification 40 SSa-. Type 28 GBS neede. Maximum recommended speed 6500 R.P.M. *Discontinued - In most instances, repacement parts are avaiabe. 4

MACHINE STYLES (Continued) 56300 W Medium throw machine, equipped with zipper guiding presser foot for crossing zipper attached to pants fy. Typica appication - For attaching waistbands to men's trousers. Seam specification 40 SSa-. Type 28 GAS neede. Maximum recommended speed 6500 R.P.M. *56300 X Medium throw machine, equipped with thumbscrew adjustabe frame neede thread eyeet, top-grip-feed mechanism and presser foot with yieding section to the eft of neede. Typica appication - For edge seaming operations on trousers, sacks, dress pants, jackets and simiar garments made of ight to medium weight materias. Maximum seam width is inch (25.4mm) necessitated by the top-grip-feed mechanism. Seam specification 40 SSa-. Type 28 GBS neede. Maximum recommended speed 6500 R.P.M. 56300 AH Medium throw machine, equipped with thumbscrew adjustabe frame neede thread eyeet, top-grip-feed mechanism and presser foot with yieding section to the eft of neede. Typica appication - For edge seaming operations on trousers, sacks, dress pants, jackets ~nd simiar garments made of ight to medium weight durabe press materias. Maximum seam width is inch (25.4mm) necessitated by the top-grip-feed mechanism. Seam specification 40 SSa-. Type 28 GBS neede. Maximum recommended speed 6500 R.P.M. 56300 AL Medium throw machine, equipped with thumbscrew adjustabe frame neede thread eyeet. Typica appication - For misceaneous operations on paper garments and pastic products requiring a ong stitch. Stitch range is 4 to 7 per inch. Seam specification 40 SSa-. Type 28 GAS neede. Maximum recommended speed 6000 R.P.M. CLASS DESCRIPTION (56400) Advanced high speed, ow throw, fat bed machines. Two needes, independent row, eft neede in front, two oopers, encosed automatic ubricating system. Type 06 GHS neede. Prepared for use with knee press for foot ifter. Maximum recommended speed 6500 R.P.M. Maximum work space to right of neede bar 8 /4 inches (209.6mm). MACHINE STYLES 56400 D To be used with Gakin cose-couped puer. Attachments not furnished with machine. Typica appication - For hemming and simutaneousy inserting eastic in tops and egs of knitted undergarments made with ight to medium weight materias. Seam specification 40 EFg-2. Standard gauge Nos. 2, 6. 56400 P Typica seeves erias. 2, 6, appication - For piecing seeves, joining shouders, setting of ordinary quaity shirts made with ight to medium weight mat Seam specification 40 LSc-2. Standard gauge Nos. 6, 8, 0, 8. 56400 R Typica appication - For attaching set-on center paits and interining strip to skirts made with ight to medium weight materias. Starts operating at neck. Seam specification -40 LSm-2. Type 06 GHS neede. Standard gauge 48. Maximum recommended speed 6500 R.P.M. *Discontinued - In most instances, repacement parts are avaiabe. 5

MACHINE STYLES (Continued) 56400 S Typica appication - For foding and attaching inside button facings to fronts of shirts made with ight to medium weight materias. Start operations at the neck. Facing strip guided next to feed dog. Seam specification 40 LSm-2. Type 06 GHS neede. Standard gauge 48. Maximum recommended speed 6500 R.P.M. 56400 T Typica appication - For piecing seeves, joining shouders and setting seeves of extra fine quaity shirts made with ight to medium weight materias. Seam specification 40 LSc-2. Type 06 GHS neede. Standard gauge Nos. 8, 0, 2, 6. Maximum recommended speed 6500 R.P.M. 56400 W Typica appication - For piecing seeves of shirts and pajamas, joining operations on woven shorts made with ight to medium weight materias, where the majority of the work consists of straight seams. Seam specification 40 LSc-2. Type 06 GHS neede. Standard gauge Nos. 8, 0, 2, 6. Maximum recommended speed 6500 R.P.M. 56400 X Typica appication - For quiting coar bands of shirts made with ight to medium weight materias. 26 gauge is equipped with a foder so that this machine can aso be used for setting seeves on extra fine quaity shirts. Seam specification 40 SSa-2 or 40 LSc-2. Type 06 GHS neede. Standard gauge Nos. 24, 26. Maximum recommended speed 6500 R.P.M. CLASS DESCRIPTION (56500) Advanced high speed, high throw, fat bed machines. Two needes, independent row, two oopers, encosed automatic ubricating system. Maximum work space to right of neede bar 8 /4 inches (209.6rnn). MACHINE STYLES 56500 A Typica appication - For seat seaming operations on trousers and simiar garments made of medium heavy to heavy weight materias. Seam specification 40 SSa-2. Type 30 GS neede. Avaiabe for 5 stitches per inch ony. Standard gauge ony. Maximum recornnended speed 6000 R.P.M. ( Formery known as Stye 56500 N-5). 56500 B Typica appication - For seaming trousers and simiar garments made of medium heavy to heavy weight materias. Seam specification 40 SSa-2. Type 30 GS neede. Avaiabe for 7 stitches per inch ony. Standard gauge ony. Maximum recommended speed 6000 R.P.M. (Formery known as Stye 56500 N-7). 56500 C Typica appication - For seaming trousers and simiar garments made of medium heavy to heavy weight materias. Seam specification 40 SSa-2. Type 30 GS neede. Avaiabe for 0 stitches per inch ony. Standard gauge ony. Maximum recommended speed 6000 R.P.M. (Formery known as Stye 56500 N-0). 56500 J Typica appication - For feing overas, coats, combination suits and simiar garments made of medium heavy weight materias. Seam specification 40 LSc-2. Type 28 GS neede. Standard gauge Nos. 6, 8. Maximum recommended speed 6000 R.P.M., depending on materia or operation. 6

MACHINE STYLES (Continued) 56500 R Typica appication - For attaching risers to dungarees, piecing seeves on denim jackets and for attaching overa bibs made of medium heavy to heavy weight materias. Seam specification 40 LSc-2. Type 28 GS neede. Standard gauge 8. Maximum recommended speed 6000 R.P.M., depending on materia or operation. 56500 U Typica appication - For seaming trousers made of durabe press materia or medium heavy to heavy weight materias. Seam specification 40 SSa-2. Type 30 GS neede. Avaiabe for 7 stitches per inch ony. Standard gauge ony. Maximum recommended speed 6000 R.P.M. CLASS DESCRIPTION (56700) Advanced high speed, ow throw, fat bed machines. Two needes, independent row, needes abreast, two oopers, encosed automatic ubricating system. Maximum work space to right of neede bar 8 /4 inches (209.6mm). MACHINE STYLE 56700 J Equipped with Tru-Front foder. Typica appication - For one operation foding and attaching Set-on center pait and interining strips to fronts of shirts and simiar garments made of ight to medium weight materias. Starts operation at neck. Paits used in garment engths and extends /4 inch (6.4mm) beyond the rows of stitching. Seam specification 40 LSm-2. Type 08 GKS neede. Standard gauge Nos. 56, 64. Maximum recommended speed 6500 R.P.M. CLASS DESCRIPTION (56900) Advanced high speed, high throw, fat bed machines. Three needes, independent row, eft neede in front, three oopers, encosed automatic ubricating system. Maximum recommended speed 6000 R.P.M. Maximum work space to right of neede bar 8 /4 inches (209.6mm). MACHINE STYLES 56900 H Typica appication - For setting seeves, shouder seaming on denim jackets made with medium heavy to heavy weight materias. Seam specification 40 LSc-3. Type 28 GAS neede. Standard gauge Nos. 8, 9. 56900 J Typica appication - For seaming operations on jackets made of medium heavy to heavy weight materias. Seam specification 40 LSb-3. Type 47 GKS neede. Standard gauge 9. 56900 P Typica appication - For attaching risers to the back of jeans made with medium heavy to heavy weight materias. Seam specification 40 LSc-3. Type 47 GKS neede. Standard gauge 9. 56900 R Typica appication - For seat seams, outseam or inseam on jeans made from heavy weight denim. Seam specification 40 LSc-3. Type 47 GS neede. Standard gauge 9. 7

NEEDLES Each neede has both a type and size number. The type number denotes the kind of shank, point, ength, groove, finish and other detais. The size number, stamped on the neede shank, denotes argest diameter of bade, measured midway between shank and eye. Coectivey, type and size number represent the compete symbo, which is given on the abe of a needes packaged and sod by UNION SPECIAL. To have neede orders prompty and accuratey fied, an empty package, a sampe neede, or the type and size number shoud be forwarded. Use description on abe. A compete order woud read: 000 needes, Type 06 GHS, Size 090/036 The type numbers of the needes recommended for each stye of machine covered by this cataog are given in the machine stye or cass description. Other needes are avaiabe, but the ones indicated are those recorrnnended to produce the most satisfactory resuts. The type numbers of the recommended needes together with their descriptions, and the sizes avaiabe are isted beow: Type 0 GS 06 GHS 08 GHS 08 GKS 26 GS 28 GS 28 GAS 28 GBS 30 GS Description and Sizes Round shank, round point, extra short, doube groove, struck groove, chromium pated - sizes 022, 025, 027, 080/032, 049, 054. Round shank, round point, extra short, doube groove, struck groove, ba eye, ba point, chromium pated - sizes 070/027, 075/029, 090/036. Round shank, round point, extra short, doube groove, struck groove, ba eye, ba point, spotted, chromium pated - sizes 070/027, 075/029, 080/032, 090/036, 00/040 0/044, 25/049. Round shank, round point, extra short, doube groove, struck groove, oversize ba eye, spotted, chromium pated - sizes 080/032, 090/036, 00/040. Round shank, round point, short, doube groove, struck groove, ba eye, chromium pated - sizes 080/032, 00/040, 054. Round shank, round point, short, doube groove, struck groove, ba eye, spotted, undersize eye and groove 27% of size of neede, chromium pated - sizes 090/036, 00/040, 0/044, 25/049, 40/054. Round shank, round point, short, doube groove, struck groove, ba eye, spotted, chromium pated - sizes 080/032, 090/036, 00/040, 0/044, 25/049, 40/054, 50/060, 70/067. Round shank, round point, short, doube groove, struck groove, ba eye, spotted, ba point, chromium pated - sizes 080/032, 090/036, 00/040, 0/044, 25/049, 40/054, 50/060. Round shank, round point, short, doube groove, struck groove, ba eye, spotted, government, chromium pated - sizes 080/032, 090/036, 00/040, 0/044, 25/049, 40/054, 50/060. 8

Type NEEDLES (Continued) Description and Sizes 43 GS Round shank, round point, 2 bag, doube groove, struck groove, spotted, chromium pated - sizes 40/054, 50/060, 70/067, 230/090. 47 GKS Round shank, round point, ong, doube groove, struck groove, oversize ba eye, spotted, short point, standard eye and grooves, chromium pated - sizes 090/036, 00/040, 0/044, 25/049, 40/054. Seection of proper neede size is determined by size of the thread used. Thread shoud pass freey through neede eye in order to produce a good stitch formati,'on. LUBRICATION Use a straight minera oi with a Saybot viscosity of 90 to 25 seconds at 00 degrees F. This is equivaent to Union Specia Corporation Specification 75. Before operating, fi machine with oi at pug screw (A, Fig. ). Whie fiing machine with oi, check gauge (B). When proper oi eve is reached, gauge neede wi register on back ine marked FULL Oi must be added when gauge neede registers on back ine marked "LOW'. Athough the machine can be operated safey when gauge neede registers in the "OPERATE" zone, it is recommended to aways check oi eve before operating, to be sure machine is fied with oi to the "FULL" mark. CAUTION: DO NOT over fi machine. To drain oi, remove pug screw (C), or ower crank chamber cover on back of machine. Oi must be changed every 2000 operating hours to minimize wear. On new machines, or a machine out of service for an extended period of time; ubricate machine as foows: Remove head cover, cean.out int, then directy oi neede bar ink and neede bar. Repace head cover and fi machine with oi to proper eve. Run machine at ow RPM to ensure proper ubrication of components preventing any damage which may occur from ack of oi distribution. Fig. 9

FIii main reservoir here. CAUTION: FIii o reservoir before starting. Machine has been drained before shipping. fu mark on gauge. Fig. 2 THREADING AND OILING DIAGRAM FOR ALL STYLES EXCEPT 56300 E,F,G,N,R,U,X,AH and AL Oi has been drained from machine before shipping and the reservoir must be fied before starting to operate. Maintain oi eve in "OPERATE" zone; add oi when neede of gauge registers on the back ine marked "LOW". Machine is automaticay ubricated and no oiing other than keeping the main reservoir fied is necessary. Refer to instructions under LUBRICATION and "CHANGING STITCH LENGTH" for additiona information. Thread machine as iustrated above for a Styes except 56300 E,F,G,N,R,U,X, AH and AL. 0

FIii main reservoir here. CAUTION: Fi o reservoir before starting. Machine has been drained before shipping. FIii reservoir to fu mark on gauge. CAUTION: Be sure ooper connection Is up before sewing. Fig. 2A THREADING AND OILING DIAGRAM FOR STYLES 56300 E,F,G,N,R,U,X,AH and AL Oi has been drained from machine before shipping and the reservoir must be fied before starting to operate. Maintain oi eve in 0PERATE zone; add oi when neede of gauge registers on the back ine marked LOW Machine is automaticay ubricated and no oiing other than keeping the main reservoir fied is necessary. Refer to instructions under LUBRICATION and "CHANGING STITCH LENGTH" for additiona information. Thread machine as iustrated above for Styes 56300 E,F,G,N,R,U,X,AH and AL.

ADJUSTING INSTRUCTIONS NOTE: Instructions stating direction or ocation, such as right, eft, front or rear of machine, are given reative to operator's position at the machine. The handwhee rotates countercockwise, in operating direction; when viewed from the right end of machine. OIL GAUGE CALIBRATION To recaibrate oi gauge, foow instructions in sequence as isted: - Pace machine upright on a eve surface. - Remove pug screw (C, Fig. ) and tip machine forward to drain a oi from reservoir. - Remove ower crank chamber cover on back of machine. - Fi reservoir unti oi is even with bottom of knee press shaft bushing (D). - Loosen ocknut (E) and rotate caibrating screw (F) as required unti gauge neede registers on the back ine marked LOW - Tighten ocknut {E), then repace pug screw (C) and ower crank chamber cover. - Fi machine with oi unti gauge neede registers on back ine marked FULL A NEEDLE BAR ALIGNMENT (TWO AND THREE NEEDLE MACHINES) Insert a new set of needes (type and size required). Turn handwhee to bring neede bar (A, Fig. 3) down to ensure that needes center in neede hoes of throat pate as shown in Fig. 3. Adjustment can be made by oosening screw (B) sighty, aowing neede bar to be turned as required. Tighten camp screw. SYNCHRONIZING LOOPER AND NEEDLE MOTIONS Insert ooper into the ooper rocker, Fig. 3 pushing it a the way down and tighten screw against fat on shank of ooper. Turn handwhee in operating direction unti the point of the ooper (A, Fig. 4) moving to the eft, is even with the eft side of the right neede (B). Note the height of the eye of the neede with respect to the ooper point (See Fig. 5). Turn the handwhee in the reverse direction unti the point of ooper again moving to the eft, is even with the eft side of right neede (See Fig. 5). If the height of the eye of the neede with respect to the ooper point are the same, ooper and neede motions are synchronized - a variation of.005 inch (.27mm) is aowabe. Fig. 4 2

SYNCHRONIZING LOOPER AND NEEDLE MOTIONS (Continued) If the distance from the eye of the neede to the point of the ooper is greater when the handwhee is turned in the operating direction, the ooper drive ever rocker shaft wi have to be moved sighty towards the rear. Moving the shaft towards the front acts the reverse. NOTE: The /64 inch (.4mm) dimension shown in Fig. 5 is for fina setting of neede bar height. Adjust ooper drive rocker ever shaft as foows: Loosen screw (C, Fig. 4) in ooper drive ever (D). A rod of.46-40 thd. or Union Specia Screw 22870 A can be threaded into the ooper drive ever rocker shaft through the center of thrust adjusting screw (E). Tap or pu sighty as required to position shaft for proper synchronization. Tighten screw (C) securey and remove rod or screw used to position shaft. Loosen ock nut (F) and TORQUE thrust adjusting screw (E) to 6 in. bs. (7cm/kg);re-tighten ock nut (F) securey. With ooper at extreme right end of its trave, check ocation of the centerine of right ooper connecting rod bearing using gauge 2227 ex for a Casses except 56700 which uses gauge 2227 CX-56 for Stye 56700 J-56 and 2227 CX-64 for Stye 56700 J-64. Remove nut from ooper ever stud (A, Fig. 6) and pace hoe in gauge (B) over threaded stud. The eft end of gauge shoud ocate against the RIGHT side of ooper rocker cone (C). If adjustment is necessary, oosen camp screw (D), reposition ooper drive ever (E) as required and retighten screw (D). If gauge is not avaiabe, setting can be checked with a scae. "X" dimension is from centerine of stud (A) to centerine of cone (C) which shoud be 4 /6 inch (03.2mm) for a Casses except 56700. Stye 56700 J-56 shoud be a 3 5/8 inch (92. nm) and Stye 56700 J-64 shoud be 3 9/6 inch (90.6mm) with ooper at extreme right end of trave. For Proper SYNCHRONIZATION of Looper & Neede these two Dimensions wi be the same J /84'H--==- (.4mm) -r in OPERATING Direction Fig. 6 Fig. 5 Looper in FRONT of Neede In REVERSE Direction LOOPER SETTINGS Fig. 7 Insert a new neede, type and size as specified. If the ooper ga_uge is 5/32 inch (4.0nm), for exampe, set the ooper (A, Fig. 7) so the distance from the center of the neede (B) to the point of the ooper is 5/32 inch (4.0mm), when the ooper is at its farthest position to the right. 3

LOOPER SEITINGS (Continued) Looper gauge 2225-5/32 (C) can be used advantageousy in making this adjustment. On two neede machines set the back ooper to the right neede and on three neede machines set the midde ooper to the midde neede, when setting the ooper gauge. Refer to chart for neede Type, ooper gauge setting and ooper gauge number. If adjment is required, oosen nut (D) (it has a eft hand thread) and nut (E) on connecting rod (F), turn the connecting rod forward or backward to obtain the 5/32 inch (4.0mm) dimension. Retighten both nuts, first nut (E), then nut (D). Make sure the eft ba joint is in vertica position and does not bind after adjustment. Machine Styes Neede Type Looper Gauge Setting Looper Gauge Number 56200 H 56200 K,R 56200 L 56200 S 56200 W, 56300 W,AL 56300 E,F,G,N,R, U,X,AH 56300 H 56300 M 56400 D 56400 P,R,S,T,W,X 56500 A,B,C,U 56500 J,R 56700 J 56900 H 56900 J 56900 P 56900 R 0 GS 06 GLS 26 GS 08 GHS 28 GAS 28 GBS 43 GS 26 GS 06 GHS 06 GHS 30 GS 28 GS 08 GKS 28 GAS 47 GKS 47 GKS 47 GS /8 Inch (3.2mm) /8 Inch (3.2mm) 5/32 Inch (4.0mm) /8 Inch (3.2mm) 5/32 Inch (4.0mm) 5/32 Inch (4.0mm) 5/32 Inch (4.0mm) 5/32 Inch (4.0mm) /8 Inch (3.2mm) /8 Inch (3.2mm) 5/32 Inch (4.0mm) 5/32 Inch (4.0mm) /8 Inch (3.2mm) 5/32 Inch (4.0ITIT) 7/32 Inch {5.6mm) 5/32 Inch (4.0ITIT) 7/32 Inch (5.6mm) 2225-/8 2225-/8 2225-5/32 2225-/8 2225-5/32 2225-5/32 2225-5/32 2225-5/32 2225-/8 2225-/8 2225-5/32 2225-5/32 2225-/8 2225-5/32 2225-7/32 2225-5/32 2225-7/32 The ooper is set correcty if, as it moves to the eft behind the neede, its point (A, Fig. 8) cears the rear of neede (B) by.002 inch (.05mm). Fig. 8 If adjustment is necessary, oosen ock screw (G, Fig. 7) and turn stop screw (H) as required. Turning stop screw cockwise sets the ooper to the rear and turning it countercockwise acts the reverse. Hoding ooper to the front whie making this adjustment may prove hepfu. Tighten ock screw when setting is obtained and recheck the adjustment. On Stye 56200 W, ooper neede guard (attached to ooper) shoud be set to barey contact the front of neede without defecting as ooper moves to eft. On the two and three neede machines, insert the other needes and oopers. The same ooper - neede reationship shoud exist without any adjustment, other than appying pressure on the ooper at front or back of bade, whie camping ooper in ooper rocker, so as to get the proper in-ine-offeed setting. 4

NEEDLE BAR HEIGHT The height of the neede is correct when the top of its eye is /64 inch (.4mm) beow the underside of the ooper, with the ooper point fush with the eft side of the neede as shown in Fig. 5. On Styes 56500 A, Band C the top of the neede eyes shoud be even with the underside of the ooper when the ooper point is fush with the eft side of the neede. If adjustment is necessary, Fig. 9 oosen screw (8, Fig. 3) and move neede bar (A) up or down as required and retighten screw. On two and three neede machines, care shoud be taken not to disturb aignment of neede bar when moving the neede bar either up or down. The descending needes must be defected aike on the back of the oope rs. FEED DOG SETTINGS Feed dog (A, Fig. 9) shoud be centered in throat pate (B) with equa cearance on a sides and ends with feed trave set to desired stitch ength. At highest point of trave, tips of feed dog teeth shoud extend the depth of a tooth or approximate.y 3/64 inch (.2mm) above throat pate and parae to same. Screw (C) shoud be set to support feed dog after screw (D) has been oosened which secures feed dog in position. On Styes 56300 N,U,X,AH the tips of the teeth must extend /32 inch (.8mm) above the throat pate and the "Grip Feed" presser foot feed dog must ine with the ower feed dog eft to right, and in-ine-of-feed the ast teeth of the top and bottom feeds shoud match tooth point to point. Fig. 0 Parae adjustment can be made by oosening nut (A, Fig. 0) and turn screw (B) cockwise to ower front of feed dog, countercockwise acts the reverse. When propery set, retighten nut (A). Right to eft adjustment can be made by oosening screws (A, Fig. ) and sighty move feed rocker (B) on feed rocker shaft (C) as required, then retighten screws. Check to ensure that feed rocker arm (D) does not bind after adjustment. Forward or rearward centering of feed dog can be accompished by oosening nut (E, Fig. ), move feed rocker (B) as required and retighten nut. Fig. From the ibrary of: Superior 5 Sewing Machine & Suppy LLC

CHANGING STITCH LENGTH Set the stitch to required ength. This is accompished by oosening ocknut (F, Fig. ) /2 turn (it has a eft hand thread) on the end of the stitch reguating stud and turning stitch adjusting screw (G) ocated under the eft end of the coth pate, in the head of main shaft (H), which is marked with L and S Turning the screw cockwise shortens the stitch (moves stitch reguating stud toward the S ) and turning it in a countercockwise direction engthens the stitch (moves stitch reguating stud toward the L ). Retighten ocknut securey. To prevent destructive damage to the feed drive bearing, key screw (J) must engage the U shaped key sot in ferrue (K). NOTE: Any change in stitch ength wi necessitate a corresponding change in the rear neede guard setting. Machines having neede bearings in the feed rocker at ocations (L, Fig. ) may require repacking after years of service. Bearings shoud be throughy ceaned and repacked with Union Specia Corporation grease 28604 P. REAR NEEDLE GUARD At extreme forward end of trave, rear neede guard (C, Fig. 0) must be set horizontay not to contact rear of neede (D) with a maximum cearance of.005 inch (.27). Guard shoud be set as ow as possibe, yet have its vertica face approach approximatey 3/64 inch (.2mm) of neede point unti point of ooper (E), moving to the eft, is even with the neede. To move neede guard forward or backward, oosen screw (F), move neede guard as required, and retighten screw. To raise or ower neede guard, oosen screw (F), and turn screw (G) cockwise to ower neede guard or countercockwise to raise it. Retighten screw (F) after guard is propery set. NOTE: Any change in stitch ength wi require a change in rear neede guard setting. THREADING (FOR ALL STYLES EXCEPT 56300 E,F,G,N,R,U,X,AH and AL) Draw the ooper and neede threads into the machine and start operating on a piece of fabric. Refer to threading diagram (Fig. 2) for the threading of these machines. THREAD TENSIONS The tension on the neede thread shoud be ony sufficient to produce uniform stitches on the under surface of the fabric. The ooper thread tension is appied at the cast-off support tension disc assemby, and the adjusting nut shoud be set so that the tension on the ooper thread is just sufficient to steady the thread. THREAD TENSION RELEASE The thread tension reease is set correcty when it begins to function as the presser foot is raised to within /8 inch (3.2rrm) of the end of its trave and is entirey reeased when the presser foot has reached its highest position. From the ibrary of: Superior Sewing 6 Machine & Suppy LLC

THREAD TENSION RELEASE (Continued) If adjustment is required, oosen tension reease ever screw (A, Fig. 2), ocated at the back of machine and move tension disc separator as required. Retighten screw. After adjustment there shoud be no binding at any point. PRESSER BAR HEIGHT Height of presser bar (A, Fig. 3) is correct when presser foot can be removed by depressing foot ifter ever (B, Fig. 2). There shoud be approximatey /6 inch (.6mm) cearance between ower surface of presser bar connection and guide (B, Fig. 3) and bottom surface of head opeining in bed casting when foot ifter ever is reeased and presser foot ying fat on throat pate with feed dog beow throat pate. Fig. 2 Adjustment can be made by turning handwhee to position neede bar at bottom of stroke. Loosen screw (C, Fig. 3) and whie hoding presser foot down on throat pate, position presser bar connection and guide as required to attain specified cearance and retighten screw. PRESSER FOOT PRESSURE ' A Reguate presser spring reguating screw (A, Fig. 4) so that it exerts ony enough pressure on the presser foot to feed the work uniformy when a sight tension is paced on the fabric. Turning it cockwise increases the pressure, countercockwise acts the reverse. NEEDLE THREAD TAKE-UP WIRE AND FRAME EYELET (FOR ALL STYLES EXCEPT 56300 E,F,G,N,R,U,X,AH and AL) Set neede thread take-up wire (B, Fig. 4), so that its upper surface is even with the top of the hoes in neede bar thread eyeet (C) when neede bar has competed its downward stroke. Lower this setting for a smaer neede thread oop, or raise it for a arger oop. Set neede thread frame eyeet (D) so that the eyeet hoe is 3/4 inch (9.0mm) above the attaching screw on a Styes except on Styes 56500 J, 56900 H, J, P and R the eyeet is to be set 5/8 inch (5.9mm) above the attaching screw and on Stye 56200 H the eyeet is to be set inch (25.4mm) above the attaching screw. NOTE: For the above setting on Styes 56300 E,F,G,N,R,U,X,AH and AL, see the foowing paragraphs. THREADING (FOR STYLES 56300 E,F,G,N,R,U,X,AH and AL) Refer to threading diagram (Fig. 2A) for the manner in which these machines are threaded. Fig. 4 Fig. 3 From the ibrary of: Superior 7 Sewing Machine & Suppy LLC

NEEDLE THREAD TAKE-UP WIRE AND FRAME EYELET FOR (STYLES 56300 E,F,G,N,R,U,X,AH and AL) Fig. 4A :.i.,j~----- Fig. 5 These machine styes are equipped with additiona thread handing and con..., tro parts, so the adjusting sequence shoud be made in the foowing manner: With neede bar at the top of its stroke, set neede thread take-up wire (A, Fig. 4A) so its ower extended surface is 7/6 inch (36.5mm) above centerine of neede ever thread eyeet hoe and 3/4 inch (9.0mm) across the centerines of its vertica surfaces (See Fig. 4A). Set ooper thread guide eyeet (A, Fig. 5) so its eft outer surface is 3/4 inch (9.0rrm) from the eft side of ooper thread take-up (B), (See Fig. 5). Adjust ooper thread tension with nut (B, Fig. 4A) to a minimum required for controing the ooper thread (ight). Set the thread index eyeet (C) at 3 on the adjusting pate (D). Changing the neede thread tension ony, with nut (E), baance the stitch so that when 6 inches (52.4mm) of sewn seam are raveed back, the neede thread is approximatey as ong as the ooper thread. A inch (25.4mm) difference in engths is permissibe. NOTE: Use a sampe of the materia to be sewn. Maintaining this neede thread tension, move thread index eyeet (C) up to toward L to obtain a ooser seam (onger neede oops) and toward T to obtain a tighter seam. Fig. 6 FEEDING PRESSER FOOT Remove the presser spring reguator and presser spring. Adjust ong stop screw (A, Fig. 6) in presser bar guide (B) against bed casting as required to ensure a cearance between the guide and top of presser bar bushing (C), yet so that guide is pued up quicky by ifter ever ink (D) when foot treade is activated. Tighten ock nut (E) on stop screw. From the ibrary of: Superior Sewing 8 Machine & Suppy LLC

FEEDING PRESSER FOOT (Continued) As a preiminary setting, adjust spring reguator nut (A, Fig. 7) on feeding presser foot so the distance from the top of spring (B) to the yoke (C) is 5/8 inch (5.9mm), (See Fig. 7). Assembe the feeding presser foot to presser bar. With presser foot resting on throat pate and feed dog down, press down on spring reguator nut {A, Fig. 7) unti the marks on presser foot bottom ine up with the centerine of neede, whie keeping the neede in the center of neede sot, tighten set screw (D) securing presser bar guide to the presser bar, making sure stop screw in presser bar guide is resting on the bed casting. Repace presser spring and presser spring reguator. Turn presser bar spring reguator screw down unti the thread portion is eve with the head casting. NOTE: Any change in the aignment of neede in reationship to the marks on the presser foot bottom probaby means that the stop screw of the presser bar guide was not seated against bed c3sting before ocking set screw. When the presser foot is ifted off the bare Fig. 7 throat pate, the foot shoud move back ony sighty, ess than /64 inch (.4mm). The stop screw {E, -Fig. 7) on the yoke, which is set at the factory, can be readjusted if necessary, shoud this dimension become changed. CHECK Presser foot at back of neede sot shoud cover most of throat pate and when resting on the bare throat pate. When the presser foot bottom is raised by materia so that the feeding foot spring bottoms, the back of the neede sot shoud cear the neede. The main presser bar shoud not ift before the feeding foot spring bottoms. The purpose of the feeding foot is to make the top and bottom py of coth feed the same amount without puing on the bottom py. The 5/8 inch {5.9mm) setting on the feeding foot spring usuay gives a good matching of pies and a strong feeding pu. Reducing this pressure wi tend to feed the top py more. Increasing this pressure wi tend to feed the bottom py more. TORQUE REQUIREMENTS Torque specifications given in this cataog are measured in inch-pounds or centimeter/kiograms. A straps and eccentrics must be tightened to 9-2 in. bs. (22-24cm/kg) uness otherwise noted. A nuts, bots, screws, etc., without torque specifications must be secured as tighty as possibe, uness otherwise noted. Specia torque specifications for connecting rods, inks, screws, etc., are shown on parts iustrations. From the ibrary of: Superior 9 Sewing Machine & Suppy LLC

Fig. 8 Fig. 9 Fig. 20.045" (.4mm) SPECIAL INSTRUCTIONS NEEDLE LEVER When adjusting neede ever or repacing reated parts, foow instructions in sequence as isted:. Insta 0 rings (A, Fig. 8) onto neede ever stud (B) and thrust coar (C). 2. With neede ever (D) in machine and positioned propery; insert stud (B) through hoe in neede ever unti its shouder contacts the neede ever and the word UP on stud is in the upright position. Whie making sure no binding exists in the neede bar ink, secure stud (B) with the front set screw in top of machine bed. 3. Insta temper oad ring (E) and compression cups (F) onto stud (B), then push ring and cups through opening in machine bed. 4. Insta thrust coar (C) onto stud (B) being carefu not to damage 0 ring. Compress components together by tightening screw (G) unti washer (H) bottoms against stud {B). Secure stud (B) in position using the rear set screw in top of bed. 5. To check temper oad ring for proper compression, remove screw (G) from stud (B) and oosen rear set screw in top of bed. Thrust coar (C) shoud spring out.003 -.007 inch (.08 -.8mm). Compress oad ring in reverse order, then tighten rear set screw. 6. With indented UP on stud (B) in upright position, insta bearing oier (J) so its hook sets in oi suppy hoe (K) of stud. When hook and stud are secured in their proper positions, the proper amount of oi wi be channeed to stud for ubricating neede ever (D). ALIGNING MAINSHAFT TO CRANKSHAFT As viewed ooking down from rear of machine, spot screws (A, Fig. 9) in the coupings must aign with the spots in the ooper drive crank (B) and set screws (C) must aign with the fats on crankshaft (D) and mainshaft (E). Mainshaft must be positioned ateray with.045 inch (.4mm) cearance between the right side of its head and the bed casting as shown in Fig. 20. 20

ALIGNING MAINSHAFT TO CRANKSHAFT (Continued) Looper drive Crank (B, Fig. 9) must be positioned ateray with /32 inch (.8mm) cearance between it and mainshaft (E) as shown in Fig. 9. Once these settings are made, it is very important that the coupings are tightened in the foowing sequence for best performance. Tighten spot screws (A) temporariy, to the ooper drive crank. Tighten set screws (C) temporariy, to the crankshaft and mainshaft. Torque screws (F) to 9-2 in. bs. (22-24cm/kg). Loosen spot screws (A) and set screws (C). Re-torque screws (F) to 9-2 in. bs. (22-24cm/kg), then, torque screws (A and C) to 9-2 in. bs. (22-24cm/kg). The oi drip pate (A, Fig. 2) ocated in the oi reservoir shoud be positioned with its tip in the recessed cut out in the bed casting, as far to the eft as possibe without touching. It has eongated mounting hoes and can be adjusted by oosening (2) screws (B) in top of the oi reservoir back cover to position as required, retighten screws. Fig. 2 From the ibrary of: Superior 2 Sewing Machine & Suppy LLC

ILLUSTRATIONS ORDERING REPAIR PARTS This cataog has been arranged to simpify ordering repair parts. Expoded views of various sections of the mechanism are shown so that the parts may be seen in their actua position in the machine. On the page opposite the iustration wi be found a isting of the parts with their part numbers, descriptions and the numbers of pieces required in the particuar view being shown. Numbers in the first coumn are reference numbers ony and merey indicate the position of that part in the iustration. Reference numbers shoud never be used in ordering parts. Aways use the part number isted in the second coumn. Component parts of sub-assembies which can be furnished for repairs are indicated by indenting their descriptions under the description of the main sub-assemby. Exampe: 9 0 2 3 2905 AK 22559 A 56343 E 56343 C 22587 K Looper Drive Lever Crank Assemby, for Styes 56200 L, W, Casses 56300, 56500 and 56900 ------------------------------ Bearing Cap Screw, ower-------------------------------- 2 Oi Spasher-------------------------------------------- Ba Joint Guide Fork----------------------------------- Bearing Cap Screw, upper-------------------------------- It wi be noted in the above exampe that the eccentric, ba stud and bearing are not isted. The reason is that repacement of these parts individuay is not recommended, so the compete sub-assemby shoud be ordered. At the back of the book wi be found a numerica index of a the parts shown in this book. This wi faciitate ocating the iustration and description when ony the part number is known. IDENTIFYING PARTS Where the construction permits, each part is stamped with its part number. On some of the smaer parts and on those where construction does not permit, an identification etter is stamped in to distinguish the part from simiar ones. Part numbers represent the same part, regardess of cataog in which they appear. IMPORTANT! ON ALL ORDERS, PLEASE INCLUDE PART NAME AND STYLE OF MACHINE FOR WHICH PART IS ORDERED. TERMS Prices are net cash and subject to change without notice. A shipments are forwarded f.o.b. shipping point. Parce Post shipments are insured uness otherwise directed. A charge is made to cover postage and insurance. 22

Before this machine eft the factory it was adjusted and inspected to give you the utmost satisfaction and durabiity at a times. If, however, the machine has been readjusted and is not sewing propery, see chart beow for suggestions which may prove beneficia to you. SKIPPED STITCHES Condition Causes Cures Neede oop too sma Take-up wire set too ow Raise take-up wire sighty Neede thread stretched at bottom of stroke, oop not formed ti stretch reieved Neede thread creased because it is too tight and neede is hot Neede thread pinched by neede guard, coapsing neede oop Thread twisting around neede Neede thread sticking in neede grooves, due to heat Length of neede eye too ong, causing deay in neede oop formation Neede does not rise enough to form neede oop propery Lower frame thread eyeet and/ or reduce neede tension Use oversize ba eye neede, ower frame neede eyeet, reduce tension Drop neede guard sighty Keep neede oop as sma as possibe, keep neede thread tension to a minimum. Use a eft twist thread Use oversize ba eye neede, to reduce friction Use neede with shorter eye, drop neede bar sighty or increase ooper gauge /64 to /32 inch Increase ooper gauge /64 to /32 inch Looper misses neede oop Materia is not hed down in Use tractor type presser foot, as presser foot is coming front of seam and is fagging if avaiabe, or see if presser off a seam bar is sticking Neede oop formed propery but brushed out of the way by ooper Neede defecting toward operator Neede bar set too high Use sharp point neede Lower neede bar sighty Looper misses neede oop Neede defecting toward oper- Do not hod back excessivey on when operator is trying to ator who may be hoding back on on materia. Propery adjust match seams or ends of gar- materia whie matching seams feed and maintain a ight ments or ends of garment presser foot pressure so operator does not hod back Machine misses neede oop Neede defecting toward the Move neede guard to the rear when stitch ength is in- operator because the neede creased guard is set too far forward Neede misses triange on Looper thread too oose, not "Increase ooper thread tension ooper thread side making a good triange NOTE: Neede being defected to the Do not pu materia at the rear by burr on neede point back. Use a sharp neede to or due to operator puing on stop neede from gancing off materia, or neede gancing seam. Check neede for burr off when coming on a seam More detaied information concerning the doube ocked stitch (stitch type 40) is avaiabe under "Stitch Formation, Type 40". 23

56 50 i

Ref. -!9..:. 2 3 4 4A 5 6 6A 7 7A 8 9 9A 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 *37 *38 39 40 4 4A 42 43 44 45 46 47 48 49 50 5 52 53 54 55 56 57 58 59 60 6 62 63 64 65 66 67 68 69 Part...!i!!..:.. 22829 2375 AV 98 A 52 A 58 A 5639 52958 8 52958 G 2396 BP 2396 AG 22569 8 56782 22733 C 2396 BR 638 M 660-74 660-75 2396 AL 660-73 2396 BK 22569 C 56382 56382 N 22585 56393 D 7947 56393 C 5294 R 2253 660-342 3573 A 56958 8 605 A 22836 660-67 57 WD 5438 C 57 WB 43296 95 22889 A 539 5758 22848 20 56470 56370 5270 8 59493 A 666-24 56382 K 56382 J 22829 56480 5280 J 22839 56380 5280 J 660-33 87 22585 A 22524 56382 G 56382 H 22548 56382 D 56382 E 56382 AA 87 56382 AB 56382 Y 22894 E 56382 L 22848 MAIN FRAME, THROAT PLATE SUPPORTS, MISCELLANEOUS COVERS AND OILING PARTS Amt. ~~~~ ~ Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Bet Guard - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Looper Thread Eyeet, for a Casses except 56900 - - - - - - - - - - - - - - - - - - Looper Thread Eyeet, for Cass 56900 - - - - - - - - - - - - - - - - - - - - - - - - - Looper Thread Guard - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Thread Eyeet, for singe neede machines - - - - - - - - - - - - - - - - - - - Looper Thread Eyeet, for two and three neede machines - - - - - - - - - - - - - - - - Neede Thread Lubricator, for Cass 56900 - - - - - - - - - - - - - - - - - - - - - - - Fet Pad - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Screw, for Cass 56900 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Head Cover, for Styes 56400 R, 56700 J, 56900 H, J, P, R - - - - - - - - - - - - - - - Pug Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Thread Lubricator Oi Reservoir, for Cass 56900 - - - - - - - - - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Connection Seeve - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Couping- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Adapter - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Oi Cup - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Thread Lubricator Oi Reservoir Bracket, for Cass 56900 - - - - - - - - - - - - Screw, for head cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2,3 Head Cover, for a Styes except 56400 R, 56700 J, 56900 H, J, P, R- - - - - - - - - - Gasket - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Head Oi Tube Camp - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Head Oi Tube Mounting Bock - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Lockwasher - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Presser Bar Connection Guide Pate - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Frame Neede Thread Eyeet, for Stye 56900 J - - - - - - - - - - - - - - - - - - - - - Screw, for Styes 56200 s, W; 56300 W, AL - - - - - - - - - - - - - - - - - - - - - - - Screw for 56958 8, for Stye 56900 J - - - - - - - - - - - - - - - - - - - - - - - - - Neede Lever Eyeet Gasket - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Nipper Spring Screw, for Styes 56200 S, W; 56300 W, AL - - - - - - - - - - - - - - - - Nipper Spring, for Styes 56200 s, W; 56300 W, AL - - - - - - - - - - - - - - - - - - - Nipper Spring Pate, for Styes 56200 S, W; 56300 W, AL - - - - - - - ~ - - - - - - - - Nipper Spring Base, for Styes 56200 S, W; 56300 W, AL - - - - - - - - - - - - - - - - Pug Screw and Screw for take-up wire - - - - - - - - - - - - - - - - - - - - - - - - - 2 Adapter Pug Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Frame Neede Thread Eyeet, for a Styes except 56300 E, F, G, N, R, U, X, AH, AL and 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Frame Neede Thread Eyeet, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Thread Take-up Wire, for Stye 56300 M, Casses 56400, 56500, 56700, 56900 and 56200 except Stye 56200 W - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Thread Take-up Wire, for Styes 56300 E, F, G, N, R, U, X, AH, AL- - - - - - - - Neede Thread Take-up Wire, for Styes 56200 W; 56300 H, W - - - - - - - - - - - - - - Base Oi Pump Assemby- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Intake Fet- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Gasket- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Drive Shaft Reservoir Cover- - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Throat Pate Support, for Styes 56200 H, K, L, W, 56300 H, M, AL and Casses 56400 56500, 56700, 56900- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Dowe Pin- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Screw, for throat pate support - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Throat Pate Support, for Styes 56200 R, Sand Cass 56300 except Styes 56300 H, M, AL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Dowe Pin- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 We Nut- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Screw, for throat pate, countersunk head, for Styes 56200 R, Sand Cass 56300 except Styes 56300 H, M, AL- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Throat Pate (See Pages 47, 49, 5, 55, 57, 59, 6, 63, 65) - - -.- - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8 Oi Reservoir Top Cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Gasket- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 Crank Chamber Cover, ower- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Gasket- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Oi Reservoir Back Cover- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Oi Drip Pate- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Oi Drip Pate Camping Bock - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Gasket- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9 *See Page 35 for thumbscrew adjustabe frame neede thread eyeet assemby 29476 MY for Styes 56300 E, F, G, N, R, U, X, AH and AL. 25

24 8~20,8 G \ \ \ \ 26

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 42 43 44 45 MAIN FRAME, BUSHINGS, OIL GAUGE AND MISCELLANEOUS OILING PARTS Part 22793 22539 R 56342 D 56394 A 635 B 6256 G 660-22 56394 C 56394 B 63494 K 660-455 63494 G 63494 F 56390 E 57890 B 22569 B 2657 X 56390 H 56390 J 660-665 56382 AC 90 56382 C 56382 B 2254 C 22733 E 56382 M 554 E 56393 W 57836 B 666-259 56390 50-895 Bk. 56393 P 52942 W 52942 AC 35897 BV 56393 Q 56390 G 56393 T 56393 L 56354 C 57954 5257 AA 57842 B 5690 Description Amt. ~ Screw - - - - - - - - - - - - - - - - - - - - - - - - - Pug Screw- - - - - - - - - - - - - - - - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - - - - Oi Gauge Adjusting Shaft - - - - - - - - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - - - - Washer- - - - - - - - - - - - - - - - - - - - - - - - - 2 Oi Retaining Ring- - - - - - - - - - - - - - - - - - - Oi Gauge Foat Lever Assemby- - - - - - - - - - - - - Oi Gauge Connecting Rod- - - - - - - - - - - - - - - - Oi Gauge - - - - - - - - - - - - - - - - - - - - - - - "0" Ring - - - - - - - - - - - - - - - - - - - - - Spring Washer- - - - - - - - - - - - - - - - - - - Nut- - - - - - - - - - - - - - - - - - - - - - - - Bushing Housing Gasket- - - - - - - - - - - - - - - - - Crankshaft Bushing Housing- - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - 3 Tension Reease Lever Shaft Bushing - - - - - - - - - - Thrust Washer - - - - - - - - - - - - - - - - - - - - - 4 Piot Ring- - - - - - - - - - - - - - - - - - - - - - - 2 Neede Thrust Bearing - - - - - - - - - - - - - - - - - 2 Neede Lever Bearing Oier and Baffe Pate Assemby- - Screw - - - - - - - - - - - - - - - - - - - - - - - - - 2 Gasket- - - - - - - - - - - - - - - - - - - - - - - - - Upper Crank Chamber Cover - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - 4 Oi Fier Pug Screw - - - - - - - - - - - - - - - - - Gasket- - - - - - - - - - - - - - - - - - - - - - - - - Neede Bar Bushing, upper - - - - - - - - - - - - - - - Oi Attraction Fet - - - - - - - - - - - - - - - - - - Feed Rocker Shaft Bushing - - - - - - - - - - - - - - - 2 Fet- - - - - - - - - - - - - - - - - - - - - - - - - - Main Shaft Bushing, eft- - - - - - - - - - - - - - - - Looper Rocker Shaft Bushing - - - - - - - - - - - - - - 2 Base Fet, front- - - - - - - - - - - - - - - - - - - - Looper Drive Lever Shaft Bushing, front - - - - - - - - Thrust Adjusting Screw- - - - - - - - - - - - - - - - - 0 Intake Fiter - - - - - - - - - - - - - - - - - - - Base Fet, rear - - - - - - - - - - - - - - - - - - - - Main Shaft Bushing, right - - - - - - - - - - - - - - - Head Oi Pump Assemby- - - - - - - - - - - - - - - - - Intake Fet- - - - - - - - - - - - - - - - - Neede Bar Bushing, ower, for a Styes except 56900 J, P, R- - - - - - - - - - - - - - - - - - - - - Neede Bar Bushing, ower, for Styes 56900 J, P, R - - Presser Bar Bushing, ower- - - - - - - - - - - - - - - Looper Drive Lever Shaft Bushing, rear- - - - - - - - - Main Shaft Bushing, intermediate- - - - - - - - - - - - 27

TORQUE TO 9-2 in bs ~(2"'-2 -..:;;;.2..:...;4 c:::.:;~~/.,:!jkg~) TORQUE TO 24-26 in. bs. (28-30cm/kg) 50 TORQUE TO 9-2 in. bs. (22-24 cm/kg) 28

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 42 43 44 45 46 47 48 49 50 5 52 53 54 55 56 57 58 59 60 6 62 63 64 65 66 67 Part Ji!!.:_ 56390 H 56390 J 660-665 56342 E 52942 AC CL2 52942 AA 660-202 2905 AK 2905 AL 22559 A 56343 E 56343 C 22587 K 56343 F 22653 L-8 22894 C 22894 D 2934 A 5636 C 29476 LL 29476 LM 29476 LN 526 M 5247 22894 J 57847 95 22574 632 L 5632 D 5632 N 22894 AB 5636 526 P 526 N 29066 R 22559 G 56350 F 660-64 56350 E 660-625 5250 D 5250 F 22586 R 56458 A 56958 A 22768 56358 27-435 8k. 56 29348 AF 22564 5254 K 22562 A 52336 W0-3 660-25 56354 D 77 5635 A 56350 G 56350 D 56458 56958 22768 56358 A CRANKSHAFT, NEEDLE LEVER AND LOOPER DRIVING PARTS Amt. Description ~ Thrust Washer- - - - - - - - - - - - - - - - - - - - - - - - - - 4 Piot Ring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Neede Thrust Bearing- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Looper Drive Lever, marked "D" - - - - - - - - - - - - - - - - - - - - - - - - Thrust Adjusting Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - Wick Oi - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Drive Lever Rocker Shaft- - - - - - - - - - - - - - - - - - - - - - - - "O" Ring, for puey and ooper drive ever rocker shaft - - - - - - - - - - - 2 Looper Drive Lever Crank Assemby, for Styes 56200 L, Wand Casses 56300, 56500, 56900- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Drive Lever Crank Assemby, for Styes 56200 H, K, R, Sand Casses 56400, 56700- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Searing Cap Screw, ower- - - - - - - - - - - - - - - - - - - - - - - - - 2 Oi Spasher- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Ba Joint Guide Fork - - - - - - - - - - - - - - - - - - - - - Bearing Cap Screw, upper- - - - - - - - - - - - - - - - - - - - - - - - - 2 Looper Drive Lever Couping- - - - - - - - - - - - - - - - - - - - - - - - - - 2 Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Set Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Spot Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Base Oi Pump, (See Ref. 43 - Page 25} - - - - - - - - - - - - - - - - - - Head Oi Pump, (See Ref. 40 - Page 27) - - - - - - - - - - - - - - - - - - Nut- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Connecting Rod Guide - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Crankshaft Assemby,.90 inch throw, for Styes 56200 L, Wand Cass 56300 except Styes 56300 H, M- - - - - - - - - - - - - - - - - - - - - - - - - - - Crankshaft Assemby,.770 inch throw, for Styes 56200 H, K, R, Sand Casses 56400, 56700- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Crankshaft Assemby,.990 inch throw, for Styes 56300 H, Mand Casses 56500, 56900- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Bearing- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28 Counterweight- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Thrust Coar- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Retaining Pate- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Handwhee- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Puey - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Neede Lever Connecting Rod- - - - - - - - - - - - - - - - - - - - - - - - - - 2 Nut- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Lever Connecting Rod Upper Sa Joint Assemby- - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Compression Cup- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Temper Load Ring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Lever Thrust Coar - - - - - - - - - - - - - - - - - - - - - - - Oi Sea Ring- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Gasket - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Sar Thread Eyeet, for two neede machines- - - - - - - - - - - - - - - Neede Bar Thread Eyeet, for three neede machines and Cass 56300 except Styes 56300 H, M, W- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Bar Thread Eyeet, for Cass 56200 and Styes 56300 H, M, W - - - - - - Neede Bar Eyeet Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Bar (See Page 43) - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Camp Nut, for Casses 56200, 56300 - - - - - - - - - - - - - - - - - - Neede Lever Assemby- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Bar Connection - - - - - - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Link Pin- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Coumbia Yarn (6 strands)- - - - - - - - - - - - - - - - - - - - - - Retaining Ring- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 Neede Bar Link - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Lever- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Bushing- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Lever Stud - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Lever Thread Eyeet, for two neede machines- - - - - - - - - - - - - - Neede Lever Thread Eyeet, for three neede machines and Cass 56300 except Styes 56300 H, M, W- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede L~ver Thread Eyeet, for Cass 56200 and Styes 56300 H, M, W - - - - - 29

2 TORQUE TO 9-2 in. bs. (22-24 cm/kg) 40B TORQUE TO 30

Ref. Part -!!!.:.. -!!!.:.. 8 2 526 N 3 5244 L 4 5244 N 5 55244 G 6 W03 7 56344 8 C067 E 9 56344 B 0 5236 A 56344 C 2 79 3 98 4 5246 5 96 6 22874 7 8 8 9 20 73 2 5784 22 22729 C 23 269 24 5240 D 57840 25 8 26 56342 E 27 22882 C 28 5242 M 29 52942 R 30 20 3 8 32 5634 M 33 5634 F 34 660-30 35 5634 E 36 5634 G 37 50-458 Bk. 38 87 U 39 56393 J 40 4 5745 42 43 5465 F 44 88 45 258 A 46 22829 47 56744 A 48 56744 49 79 50 98 5 96 52 280 53 5675 54 570 D 55 56772-56 56772-64 56 4077 57 5770-56 5770-64 58 577 59 22835 60 5784 A 6 22729 C 62 4047 63 29476 LV 64 5634 F Ref. 40A 40B 40C 40D 40E - LOOPER ROCKER AND CONNECTING ROD PARTS Amt. Description ~ Nut, for a Styes except 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - Washer, for a Styes except 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - Thrust Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Looper Rocker Shaft Camp, for a Styes except 56700 J - - - - - - - - - - - - - - - - Looper Rocker Shaft Coar Stud, for a Styes except 56700 J - - - - - - - - - - - - - Coumbia Woo Yarn (4 strands - 8 inches ong) - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Shaft, for a Styes except 56700 J - - - - - - - - - - - - - - - - - - - Cork Pug - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Shaft Arm - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Avoid Link Pin - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Frame, for a Styes except 56700 J - - - - - - - - - - - - - - - - - - - Stop Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Stud Nut, for a Styes except 56700 J - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Frame Lock Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Nut, for a Styes except 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper (See Pa~e 45) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Coar (See Page 45) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -,2,3 Looper Connecting Rod Ba Joint, eft, for a Styes except 56700 J - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Nut, eft hand thread - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Connecting Rod, for a Styes except 56700 J and Cass 56400 - - - - - - - - - - Looper Connecting Rod, for Cass 56400 - - - - - - - - - - - - - - - - - - - - - - - - - Nut, right hand thread - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Drive Lever, marked "D"- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Lever Stud - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Connecting Rod Jointed Section Assemby, right, for a Styes except 56700 J- - - Ferrue - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Truarc Ring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Hinge Pin - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Spring Pin - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Connecting Rod Ba Joint Oier, eft - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Assemby (See Chart Beow) - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Cone Stud - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker (See Chart Beow) - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Cone - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Lock Nut - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Lock Nut Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Shaft, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Frame, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - Stop Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Set Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Spot Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Rocker Stud Nut, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - - - 2 Looper Rocker Shaft Thrust Washer, eft, for Stye 56700 J- - - - - - - - - - - - - - - - Nut, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Looper Rocker Spacing Pate, for 56 gauge, Stye 56700 J - - - - - - - - - - - - - - Looper Rocker Spacing Pate, for 64 gauge, Stye 56700 J - - - - - - - - - - - - - - Nut, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Looper Rocker Link, for 56 gauge, Stye 56700 J - - - - - - - - - - - - - - - - - - - Looper Rocker Link, for 64 gauge, Stye 56700 J - - - - - - - - - - - - - - - - - - - Looper Rocker Link Ferrue, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - 2 Screw, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Connecting Rod Ba Joint, eft, for Stye 56700 J - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Looper Connecting Rod, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - - - Looper Connecting Rod Assemby, right, for Stye 56700 J - - - - - - - - - - - - - - - - Ferrue - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Ref. 40 Ref. 42 I. D. Amt. Assemby Rocker Mark For Machines Req. 2992 V 5633 s Casses 56200, 56300 2992 X 5673 V Cass 56700 2 2992 W 5643 u Cass 56400 2992 AA 5653 X Cass 56500 2992 Y 5693 z Styes 56900 H, p - 5693 A AB Styes 56900 J, R 3

~- ' ' ' ' 38 ---- 37.~ 29 RIGHT HEAD T SIDE OF MAIN (.4 0 BE SET SHAFT _.:..;;.~mu.,m) FROM B EDCA'3TING 045 INCH TORQUE T 9-2 (22-24 i;~/kbs. --=.., g) //'-. <. /// / ~~~6';;, ' / / 5!J ' / 4 't--=----- 5i---~~~,taL ' s--- srr~- ' ~~ _...-,--!J TORQUE TO 55 in. bs (63cm/kgi _()_.J-nCS - () ~~ 32

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 29 A 29 B 30 3 32 32 A 33 34 35 36 37 38 39 40 4 42 43 44 45 46 47 48 49 50 5 52 53 54 55 Part 29476 MJ 55235 E 6042 A 55235 D 77 56336 B 56336 C 5054 666-49 269 2657 E 22525 A 56322 C 22798 C 56336 660-269 B 56336 D 22543 A 5622 A 56722 E 56322 B 2289 B 29476 NM-062 29476 NM-080 29476 NM-096 22894 AA 77 39543 N 29476 NM-054 29476 NM-072 29476 NM-062 29476 NM-080 22894 AA 77 56323 56423 56723 22764 C 22580 D 56334 N 56334 P 56334 L 22863 C 6042 A 258 A 22637 P-24 2265 CB-4 56335 L 56335 D 98 56334 B 56335 G 2265 CD-4 660-438 439 634 J 22834 A 2280 22875 H 6434 G 22528 5236 A MAIN SHAFT, TAKE-UPS AND FEED DRIVING PARTS Description Feed Rocker Ann and Feed Crank Link Sub-Assemby - - - - - - - - - - Nut- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Locking Stud - - - - - - - - - - - - - - - - - - - - - - - - - - Screw, for ink pin - - - - - - - - - - - - - - - - - - - - - - Feed Crank Link - - - - - - - - - - - - - - - - - - - - - - - - Feed Crank Link Ferrue - - - - - - - - - - - - - - - - - - Feed Crank Link Pin - - - - - - - - - - - - - - - - - - - - - - Oi Wick - - - - - - - - - - - - - - - - - - - - - - - - - - Nut, eft thread - - - - - - - - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 Main Shaft Head Pate - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Crank Stud, marked "A" - - - - - - - - - - - - - - - - - - - - Quad Ring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Crank Stud Insert - - - - - - - - - - - - - - - - - - - - - - - Stitch Reguating Screw - - - - - - - - - - - - - - - - - - - - - - Main Shaft, for a Styes except 56700 J - - - - - - - - - - - - - Main Shaft, for Stye 56700 J - - - - - - - - - - - - - - - - - - - Gasket - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Oi Fow Reguating Screw - - - - - - - - - - - - - - - - - - - Feed Lift Eccentric Assemby, for Styes 56200 H,K,R,S; 56300 U,X; 56700 J and Cass 56400 - - - - - - - - - - - - - - - - - - - - - - Feed Lift Eccentric Assemby, for Styes 56200 L,W; 56500 A,B,C,J, U, 56900 H,J,P and 56300 except Styes 56300 H,M,U,X - - - - - - - Feed Lift Eccentric Assemby, for Styes 56300 H,M; 56500 R; 56900 R - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Spot Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw, for ink pin - - - - - - - - - - - - - - - - - - - - - - Thrust Washer, for feed bar - - - - - - - - - - - - - - - - - - - - 2 Looper Avoid Eccentric Assemby~ for Cass 56400 - - - - - - - - - - Looper Avoid Eccentric Assemby, for Styes 56200 L, 56300 W, Casses 56500 and 56900 - - - - - - - - - - - - - - - - - - - - - - Looper Avoid Eccentric Assemby, for Styes 56200 H,K,R,S: 56300 E,F,G,N,R,U,X,AH,AL; 56700 J - - - - - - - - - - - - - - - - - - - Looper Avoid Eccentric Assemby, for Styes 56200 W; 56300 H,M - - - Spot Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw, for ink pin - - - - - - - - - - - - - - - - - - - - - - Looper Thread Take-up, for Styes 56200 L,W and Casses 56300, 56500 and 56900 - - - - - - - - - - - - - - - - - - - - - - - - - - Looper Thread Take-up, for Styes 56200 H,K,R,S and Cass 56400 - - Looper Thread Take-up, for Stye 56700 J - - - - - - - - - - - - - - Spot Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - Set Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Bar, for a Styes except 56300 N,U,X,AH - - - - - - - - - - - Feed Bar, for Styes 56300 N,U,X,AH - - - - - - - - - - - - - - - - feed Dog Hoder - - - - - - - - - - - - - - - - - - - - - - - - Feed Dog Hoder Adjusting Screw - - - - - - - - - - - - - - - - Feed Dog Hoder Washer - - - - - - - - - - - - - - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Dog Height Adjusting Screw - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Rocker Shaft - - - - - - - - - - - - - - - - - - - - - - - - - Feed Rocker Shaft Coar - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Feed Bar Shaft - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Rocker - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Retaining Ring - - - - - - - - - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Bar Washer - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Neede Guard Adjusting Screw - - - - - - - - - - - - - - - - - - - - Neede Guard (See Page 43) - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw, for neede guard - - - - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw, for feed dog - - - - - - - - - - - - - - - - - - - - - - - - Feed Dog {See Pages 47,49,5,55,57,59,6,63,65)- - - - - - - - - - - Link Pin - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Amt. ~ 33

34

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 LOOPER THREAD TAKE-UP PARTS AND THUMBSCREW ADJUSTABLE FRAME NEEDLE THREAD EYELET ASSEMBLY Part 22528 2657 E 5959 D 5959 K 5959 B 50-26 Bk. 52804 A 28 28 22768 56358 E 5557 5492 5459 A 5959 J 52804 A 5457 A 5704 5757 B 29476 MY 56304 56358 B 56358 C 58 B 98 A 56358 D 22837 20 22848 Description Amt. ~ Screw - - - - - - - - - - - - - - - - ~ - - - - Washer - - - - - - - - - - - - - - - - - - - - Tension Nut - - - - - - - - - - - - - - - - - - Tension Spring - - - - - - - - - - - - - - - - Tension Disc - - - - - - - - - - - - - - - - - 2 Dowe Pin - - - - - - - - - - - - - - - - - - - 2 Cast-off Pate, for a Styes, except 56700 J- Screw, for a Styes, except 56300 E,F,G,N,R, U,X,AH,AL - - - - - - - - - - - - - - - - - - 2 Screw, for Styes 56300 E,F,G,N,R,U,X,AH,AL - - Screw, for Styes 56300 E,F,G,N,R,U,X,AH,AL - - Looper Thread Guide Eyeet, for Styes 56300 E,F,G,N,R,U,X,AH,AL - - - - - - - - - - Take-up Shied, for Casses 56200, 56300 - - - Tension Post, for Casses 56400, 56500, 56700, 56900 - - - - - - - - - - - - - - - - - - - - Looper Thread Guide, for Casses 56400, 56500, 56700 - - - - - - - - - - - - - - - - - - - - Looper Thread Guide, for Cass 56900 - - - - - Cast-off Pate, for a Styes, except 56700 J- Take-up Shied, for Casses 56400, 56500, 56900 - - - - - - - - - - - - - Cast-off Pate, for Stye 56700 J - - - - - - - Take-up Shied, for Stye 56700 J - - - - - - - Thumbscrew Adjustabe Frame Neede Thread Eyeet Assemby, for Styes 56300 E,F,G,N,R,U,X,AH, AL - - - - - - - - - - - - - - - - - - - - - - Adjusting Pate - - - - - - - - - - - - - - Guide Bock - - - - - - - - - - - - - - - - Guide Washer - - - - - - - - - - - - - - - Eyeet - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - 35

r - Qm_/ 2r 'I 9 J. L_ 36

Ref. Part 43266 2 549 C 3 5292 D 4 5292 A 5 56392 E 6 09 7 56392 F 8-9 39592 AK 0 39592 Z - 2 22598 C 3 80557 Ref. Part 4 2657-4 5 5992 A 6 56382 X 7 2657-3 8 52892 9 59292 A 20 59292 Ref. Part 8 5292 F-5 8 5292 F-8 8 5292 F-4 5292 F- 5292 F-2 DISC THREAD TENSION PARTS AMOUNT REQUIRED One Two Three Neede Neede Neede Description Machine Machine Machine Nut 2 Lead-in Guide 2 4 Tension Thread Eyeet 2 4 Ferrue 2 4 Tension Post 2 4 Tens ion Disc 4 8 Tension Spring Shied 2 4 Neede Thread Tension Spring (See Chart Beow) Tension Spring Ferrue 2 Tension Nut 2 I : I Looper Thread Tension Spring (See Chart Beow) Screw Washer 2 I - I Description 5 6 6 6 6 2 6 6 6 2 Amt. Req. Tension Disc Separator, for Singe neede machine Styes 56300 E, F, G, N, R, U, X, AH; Two and Three neede machines - - - - - - - Tension Post Support, for Three neede machines - - - - - - - - - Tension Post Support, for Singe neede machine Styes 56300 E, F, G, N, R, U, X, AH and Two neede machines - - - - - - - - - - Tension Disc Separator, for Singe neede machine Styes 56200 H, K, L, R, S, W, 56300 H, M, W, AL - - - - - - - - - - - - - - - - Tension Post Support, for Singe neede machine Styes 56200 H, K, L, R, S, W, 56300 H, M, W, AL - - - - - - - - - - - - - - - - - - Fet Washer, for auxiiary tension post support- - - - - - as required Auxiiary Tension Post Support, for Singe neede machine Styes 56300 E, F, G, N, R, U, X, AH; Two and Three neede machines- - - TENSION SPRING CHART Amt. Description Machine Stye Req. Neede Thread Tension Spring 56200 H, K, R, S 56400 D,P,R,S,T,W,X; 56700 J 2 Neede Thread Tension Spring 56200 L; 56300 E, F, G, M, N, R, U, W, X, AH, AL 56500 A, B, C, J, R, u, 2 56900 H, J, P. R 3 Neede Thread Tension Spring 56200 W, 56300 H Looper Thread Tension Spring 56200 H, K, R, s 56400 D, P, R, S, T, W, X; 56700 J 2 Looper Thread Tension Spring 56200 L, W, 56300 E, F, G, H, M, N, R, U, W, X, AH, AL 56500 A, B, C, J, R, U 2 56900 H, J, P, R 3 37

5 I I 24 L_ t\ 28 3 29~ 30 ~ 38

Ref. Part 2657 W 2 2657 Y 3 22596 4 402 5 5283 H 6 660-207 7 39552 C 8 53783 N 9 22537 0 56357 A 22840 C 2 5430 F 3 402 4 53 5 5257 M 6 402 7 22758 C 8 22557 G 9 56383 D 20 56383 AA 2 56383 AB 22 56356 52889 A 23 5256 C 24 56383 A 25 53 26 5957 E 27 53787 28 5257 K 29 30 5957 D 3 C067 D TENSION AND LIFTER LEVER PARTS Amt. Description ~ Tension Reease and Lifter Lever Shaft - - - - - - - - - - Tension Reease and Lifter Lever Shaft Connection - - - - Screw - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - Lifter Lever - - - - - - - - - - - - - - - - - - - - - Oi Sea Ring - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - Lifter Lever Connection - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - Presser Bar Connection and Guide, for Styes 56300 F, R- - Screw - - - - - - - - - - - - - - - - - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - Presser Bar Connection and Guide, for a Styes except 56300 F, R- - - - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - Lifter Lever Be Crank Spring - - - - - - - - - - - - - - Lifter Lever Be Crank - - - - - - - - - - - - - - - - - Lifter Lever Connecting Rod- - - - - - - - - - - - - - - - Presser Spring Reguator, for a styes except 56900 R- - Presser Spring Reguator, for Stye 56900 R- - - - - - - - Presser Spring, for Styes 56200 H, K, R, S, 56300 U, X- - Lifter Lever Link- - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - - - - - Presser Bar, for Styes 56900 J, P - - - - - - - - - - - - Presser Spring, for Styes 56200 L, W, 56300 E, F, G, H, M, N, R, W, AH, AL and Casses 56400, 56500, 56700, 56900 - - - - - - - - - - - - - - - - - - - - - - - - - - Presser Bar, marked A, for a Styes except 56900 J, P, R - - - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot (See Pages 47, 49, 5, 53, 55, 57, 59, 6, 63, 65) - - - - - - - - - - - - - - - - - - - - - - - - - Presser Bar, for Stye 56900 R - - - - - - - - - - - - - - Cork- - - - - - - - - - - - - - - - - - - - - - - - - 39

~-Ii r ~I,--.,!, ' ' _, ' i"--2e 29 3B 40

Ref. ~ 2 3 3A 3B 3C 30 4 5 6 7 8 9 0 OA OB OC 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 Part 25 24 5638-22 5638-222 5638-207 5638 C-207 5638 E-207 5638-87 528 AC 22845 B 35772 H 22760 A 22839 C 22526 C 5630 5630 A 5640 5670 23438 B 23437 Y 90 23437 B 23425 T 22585 2957 E 22735 2325 BG-5/8 2325 BG-3/4 2325 BG-7/8 90 23425 T 23322 AC 90 23322 AB-3/4 23322 AB-7/8 23322 AB- 23322 AB- /8 23322 AB- /4 25 C 23425 V 23438 A 90 23439 A 25 TB 2657 E 24 S CLOTH PLATES, CLOTH PLATE COVERS, EDGE GUIDES ANO BINDERS Description Amt. ~ Screw, for edge guide - - - - - - - - - - - - - - - - - - - - - - - 2 Edge Guide, for Styes 56200 H, S, 56500 A, B, C, U and Cass 56300 except 56300 H, M - - - - - - - - - - - - - - - - - - - - - - - - Coth Pate Cover, 3 5/6 inches wide, for Styes 56300 F, R, X, AH - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Coth Pate Cover, 3 5/32 inches wide, for Styes 56200 R, S, 56300 E, G, N, U, W - - - - - - - - - - - - - - - - - - - - - - - Coth Pate Cover, 3 5/64 inches wide, for Styes 56300 H, AL, and Casses 56400, 56500, 56900 except 56400 R, S-48 - - - - - - - - - Coth Pate Cover, 3 5/64 inches wide, for Styes 56200 H, K, L, 56300 M - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Coth Pate Cover, 3 5/64 inches wide, for Stye 56200 I~ - - - - - Coth Pate Cover, 2 59/64 inches wide, for Styes 56400 R, S-48, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Coth Pate Cover Spring - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Spring Washer - - - - - - - - - - - - - - - - - - - - - - - - - 3 Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Screw, for coth pate - - - - - - - - - - - - - - - - - - - - - - 2 Screw, for coth pate - - - - - - - - - - - - - - - - - - - - - - 3 Coth Pate, for Styes 56200 R,S, 56300 E, F, G, R, W - - - - - - Coth Pate, for Styes 56300 N, U, X, AH - - - - - - - - - - - - - Coth Pate, for Styes 56200 H, K, L, W, 56300 H, M, AL and Casses 56400, 56500, 56900 except 56400 R, S-48 - - - - - - - - - - - - - Coth Pate, for Styes 56400 R, S-48, 56700 J - - - - - - - - - - Body Fabric Lead-in Patfonn, for Styes 56200 Land 56300 M - - - Binder Swinging Bracket, for Styes 56200 Land 56300 M - - - - - - Screw, for binder - - - - - - - - - - - - - - - - - - - - - - - - - 2 Binder Swinging Bracket Support, for Styes 56200 Land 56300 M - - Camping Pate, for Styes 56200 Land 56300 M - - - - - - - - - - Screw, for binder swinging bracket support - - - - - - - - - - - - 2 Spring Washer, for binder swinging bracket - - - - - - - - - - - - Screw, for binder swinging bracket - - - - - - - - - - - - - - - - Engish Binder, uses sevage edge binding strip 5/8 inch wide, 5/32 inches capacity for body fabric, finsihes 5/6 inch wide, for Styes 56200 Land 56300 M - - - - - - - - - - - - - - - - - - - - Engish Binder, use 3/4 inch strip and finishes 3/8 inch, for Styes 56200 Land 56300 M - - - - - - - - - - - - - - - - - - - - - - - Engish Binder, uses 7/8 inch strip and finishes 7/6 inch, for Styes 56200 Land 56300 M - - - - - - - - - - - - - - - - - - - - Screw, for binder support - - - - - - - - - - - - - - - - - - - - - 2 Camping Pate, for Stye 56200 K - - - - - - - - - - - - - - - - - 2 Binder Support, for Stye 56200 K - - - - - - - - - - - - - - - - - Screw, for binder - - - - - - - - - - - - - - - - - - - - - - - - - 2 Cut Edge Binder, uses strip cut 3/4 inch wide, finishes 7/32 inch wide, for Stye 56200 K - - - - - - - - - - - - - - - - - - - - - Cut Edge Binder, uses strip cut 7/8 inch wide, finishes /4 inch wide, for Stye 56200 K - - - - - - - - - - - - - - - - - - - - - Cut Edge Binder, uses strip cut inch wide, finishes 9/32 inch wide, for Stye 56200 K - - - - - - - - - - - - - - - - - - - - - Cut Edge Binder, uses strip cut /8 inch wide, finishes /32 inch wide, for Stye 56200 K - - - - - - - - - - - - - - - - - - - Cut Edge Binder, uses strip cut /4 inch wide, finishes 3/32 inch wide, for Stye 56200 K - - - - - - - - - - - - - - - - - - - Screw, for body fabric ead-in patfonn - - - - - - - - - - - - - - 2 Washer Pate, for Stye 56200 K - - - - - - - - - - - - - - - - - - Body Fabric Lead-in Patfonn, for Stye 56200 K - - - - - - - - - - Screw, for pin tension - - - - - - - - - - - - - - - - - - - - - - Pin Tension, for binding on Styes 56200 K, 56200 Land 56300 M - - Screw, for edge guide - - - - - - - - - - - - - - - - - - - - - - - Washer, for edge guide - - - - - - - - - - - - - - - - - - - Edge Guide, for Stye 56200 W - - - - - - - - - - - - - - - - - - - 4

2& 25 40 ~24 ~ ~ 42

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 22A 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 42 43 44 45 46 47 48 49 50 5 52 53 54 55 Part 527 C 56 56325 2280 547 C-6 547 C-8 547 C-0 547 C-2 547 C-6 547 C-8 50 J-6 98 548-6 89 56425 547 D 50 J-40 548 K-24 548 K-26 548 B-32 548 D-48 5657 B-6 50 J-6 548-6 5657 B-8 50 J-6 708 E-5 7040-6 87 B 56525 29202 M- 29202 N- 5657 D- 5657 E- 50 J-6 558 G- 558 C- 89 88 B 22729 56525 B 56525 C 29202 L- 5657 C- 50 J-6 5658 C- 89 22743 22729 56525 A 577 578 A-56 578 A-64 22894 P 98 578 B-64 578 B-56 2253 B 605 A 56725 5697 50 J-26 3588 N-8 3588 N-9 22752 22580 56925 597 A 50 J-26 598-7 NEEDLE BARS, NEEDLE HOLDERS AND NEEDLE GUARDS Description Neede Bar, marked "CU", for Casses 56200, 56300 - Neede Camp Nut, for Casses 56200, 56300 - - - - Neede Guard, for Casses 56200, 56300 - - Screw - - - - - - - - - - - - - - - - _ - - - - _ Neede Bar, marked "CV-6", for 6 gauge, Stye 56400 P - Neede Bar, marked "CV-8", for 8 gauge, Styes 56400 P, T, W Neede Bar, marked "CV-0", for 0 gauge, Styes 56400 P, T, W, Neede Bar, marked "CV-2", for 2 gauge, Styes 56400 D, P, T, W - Neede Bar, marked "CV-6", for 6 gauge, Styes 56400 D, P, T, W - - Neede Bar, marked "CV-8", for 8 gauge, Stye 56400 P - Stop Pin - - - - - - - - - - - - - - Screw, for neede - - - - - - - - - - - - - - - - Amt. ~ - - - - - - - - 2 Neede Hoder, marked "D-6", for a gauges Styes 56400 D, P, T, Wand 6 gauge, Stye 56500 J - - - - - - - - - Spot Screw - - - - - - - - - - - - - - - Neede Guard, for Cass 56400, a gauges - - - - - - Neede Bar, marked "DE", for Nos. 24, 26, 32, 48 gauges, Styes 56400 R, S, X Stop Pin - - - - - - - - - - - - Neede Hoder, marked "L-24", for No, 24 gauge, Stye 56400 X - - Neede Hoder, marked "L-26", for 26 gauge, Stye 56400 X - - Neede Hoder, marked "D-32", for 32 gauge, Stye 56400 S - - Neede Hoder, marked "AC-48", for 48 gauge, Styes 56400 R, S Neede Bar, marked "ET", for 6 gauge, Stye 56500 J - - - - - ----- Stop Pin - - - - - - - - - - - - - - - - - Neede Hoder, marked "D-6", for 6 gauge, Stye 56500 J and a gauges Stye 56400 D, P, T, W - - - - - - - - - - - - - - - - Neede Bar, marked "EU", for 8 gauge, Stye 56500 J, R - Stop Pin - - - - - - - - - - - - - - - - - - - - - - - - - Neede Hoder, marked "G-5", for 8 gauge, Styes 56500 J, R Thread Guide - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - Neede Guard, for Styes 56500 J, Ra gauges Neede Bar Assemby, for 7 S. P.I., Styes 56500 B, U Neede Bar Assemby, for 0 S.P.I., Stye 56500 C Neede Bar, marked "EK", for 7 S. P. I., Styes 56500 B, U Neede Bar, marked "EL", for 0 S.P. I., Stye 56500 C - - Stop Pin - - - - - - - - - - - - - - - - Neede Hoder, marked "P-", for 7 S.P. I., Styes 56500 B, U Neede Hoder, marked "Q-", for 0 S.P.I., Stye 56500 C - Spot Screw - - - - - - - - - - - - - - - Screw, for neede - - - - - - - Screw, for neede - - - - - - - Neede Guard, for 7 S.P.I., Styes 56500 B, U - - - Neede Guard, for 0 S.P.I., Stye 56500 C - - Neede Bar Assemby, for 5 S.P.I., Stye 56500 A - - Neede Bar, marked "ES", for 5 S. P. I., Stye 56500 A Stop Pin - - - - - - - - - - - - - - - - Neede Hoder, marked "AS", for 5 S.P.I., Stye 56500 A - Spot Screw - - - - - - - Screw, for neede - Screw, for neede - - - - - - Neede Guard, for 5 S.P.I., Stye 56500 A - Neede Bar, marked "AU", for Stye 56700 J a gauges - - - - Neede Hoder, marked "AB-56", for 56 gauge, Stye 56700 J Neede Hoder, marked "AB-64", for 64 gauge, Stye 56700 J - - - - - Spot Screw - - - - - - - - - - - - - - - - - - - Screw, for neede - - - - - - - - - - - - - - - - 2 Neede Stop and Thread Eyeet, for 64 gauge 2 Neede Stop and Thread Eyeet, for 56 gauge - Screw, for 64 gauge - - - - - - - - - - - - - - - 2 Screw, for 56 gauge - - - - - - - - - - - - - - - - - - - 2 Neede Guard, for Stye 56700 J a gauges - - - - Neede Bar, marked "EP-9", for Nos. 8, 9 gauges, Styes 56900 H, J, P, R- - - Stop Pin - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Neede Hoder, marked "C-8", for 8 gauge, Stye 56900 H - - - - - - Neede Hoder, marked "C-9", for 9 gauge, Styes 56900 H, J, P, R - - - - Screw, for center neede - - - - - - Screw, for neede - - - - - - - - - - - - Neede Guard, for Cass 56900 a gauges Neede Bar, marked "DC", for No, 7 gauge, Stye 56900 H - - Stop Pin - - - - - - - - - - - - - - Neede Hoder, marked "E-7", for 7 gauge, Stye 56900 H - - - - - 2 43

A...~ ~2 23 44

Ref. Part 5409 C 2 5409 5409 3 5408-6 4 5408-8 5 5408-0 6 5408-2 7 5408-6 8 5408-8 *5408-24 *5408-26 *5408-32 *5408-48 9 5509 C 0 5508 G- 5508 C- 2 5508 H- 3 5909 C 5909 C 4 5508 M-6 5 5508 M-8 6 5709 7 5708 8 5909 D-9 5909 D-8 5909 D-7 9 5909 C 20 5908 B-9 5908 B-8 5908 B-7 2 220 A 22 220 23 73 24 5208 25 5208 D 26 5409 B 27 5208 W 28 520 29 73 A *Not shown on picture pate. LOOPER, LOOPER COLLARS AND LOOPER NEEDLE GUARDS Amt. Description ~ Looper, for Stye 56200 Land Cass 56300 except Styes 56300 H, M, AL - - - - - - - - - - - - - - - - - - - - Looper, for Styes 56200 K, R - - - - - - - - - - - - - - - Looper, back, for Cass 56400 a gauges, Styes 56400 R, S- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Looper, front, for 6 gauge, Stye 56400 P - - - - - - - Looper, front, for 8 gauge, Styes 56400 P, T, W- - - - Looper, front, for 0 gauge, Styes 56400 P, T, W - - - Looper, front, for 2 gauge, Styes 56400 D, P, T, W- - Looper, front, for 6 gauge, Styes 56400 D, P, T, W- - Looper, front, for 8 gauge, Stye 56400 P- - - - - - - Looper, front, for 24 gauge, Stye 56400 X- - - - - - - Looper, front, for 26 gauge, Stye 56400 X- - - - Looper, front, for 32 gauge, Stye 56400 S- - - - Looper, front, for 48 gauge, Styes 56400 R, S- - Looper, back, for Styes 56500 A, B, C, U - - - - - - - Looper, front, for 7 S.P.I., Styes 56500 B, U- - - - Looper, front, for 0 S.P.I., Stye 56500 C - - - - - - - - Looper, front, for 5 S.P.I., Stye 56500 A- - - - - - Looper, for Stye 56300 M - - - - - - - - - - - - - - - - - Looper, back, for Styes 56500 J, R - - - - - - - - - - - - Looper, front, for 6 gauge, Stye 56500 J- - - Looper, front, for 8 gauge, Styes 56500 J, R- - Looper, eft, for Stye 56700 J a gauges- - - - - - - - - Looper, right, for Stye 56700 J a gauges - - - - - - - - Looper, back, for 9 gauge, Styes 56900 H, J, P, R- - - Looper, back, for 8 gauge, Stye 56900 H- - - - - - - - Looper, back, for 7 gauge, Stye 56900 H- - - - - - - - Looper, for Stye 56300 M, midde ooper for Cass 56900 and back ooper for Styes 56500 J, R- - - - - - - - - - - Looper, front, for 9 gauge, Styes 56900 H, J, P, R - - Looper, front, for 8 gauge, Stye 56900 H - - - - - - - Looper, front, for 7 gauge, Stye 56900 H - - - - - - - Looper Coar, for Styes 56200 H, K, R, Sand Cass 56300 except Styes 56300 G, H, M- - - - - - - - - - - - - - - - Looper Coar, for Styes 56200 L, W, 56300 H, M, 56700 J -,2 Screw, for ooper - - - - - - - - - - - - -,2,3 Looper, for Stye 56300 H - - - - - - - - - - - - - - - - - Looper, for Styes 56200 H, S - - - - - - - - - - - - Looper, back, for Styes 56400 R, S - - - - - - - Looper, for Styes 56200 W, 56300 AL- - Looper Neede Guard, for Stye 56200 W- - Screw, for ooper neede guard- - - - - 45

46

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 42 43 44 45 46 47 48 49 50 5 52 FEED DOGS, THROAT PLATES, PRESSER FEET AND TOP GRIP-FEED DRIVING PARTS Part 9205 E 9224 E 56305 AL 56324 AL 5205 R 56224 H 5320 M 5330 AJ 9 87 B 74 B 5330 AH 5330 W 5330 AG 5334 A 5334 D 22758 G 22875 J 28 5334 C 2256 5330 S 56305 5324 K 56320 5330 Z 9 096 2256 604 946 A 5330 AB 56330 F 56330 G 56330 5330 AD 5330 AE 22738 9205 E 5324 F 56320 U 5330 M 9 096 22738 594 A 5330 R 56330 E 5330 N 6430 BT 56330 F 5330 P * 87 U *5330 S *56334 F Description Feed Dog, 6 teeth per inch, for Styes 56300 G, U - - - - - - - Throat Pate, for Styes 56300 G, W - - - - - - - - - - - Feed Dog, 2 teeth per inch, for Stye 56300 AL - - - - - - - - Throat Pate, for Stye 56300 AL - - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for Stye 56200 H - - - - - - - - - Throat Pate, for Stye 56200 H - - - - - - - - - - - - - - - - Presser Foot, for Styes 56200 H, 56300 G, AL - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - Chain Cutting Knife - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom - - - - - - - - - - - - - - - - - - - - Top Grip Feed Presser Foot Driving Arm, for Styes 56300 N, U, X, AH - - - - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Connecting Rod, for Styes 56300 N, U, X, AH - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw, for top grip feed presser foot driving arm - - - - - - - 2 Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Connecting Rod Fat Spring, for Styes 56300 N, U, X, AH - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - Chain Cutting Knife, for Styes 56300 N, U, X, AH - - - - - - - Feed Dog, 6 teeth per inch, for Stye 56300 X - - - - - - - - - Throat Pate, for Stye 56300 X - - - - - - - - - - - - Presser Foot, for Stye 56300 X - - - - - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Yieding Section - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, marked AG - - - - - - - - - - - - - - Presser Foot Feeding Section, 6 teeth per inch- - - - - - - Feed Section Guide - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Feed Dog, 6 teeth per inch, for Styes 56300 G, U - - - - - - - Throat Pate, for Styes 56300 N, U- - - - - - - - - - - - - - - Presser Foot, for Stye 56300 U - - - - - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 Hinge Pin - - - - - - - - - - - - - - - - - - - - - - - Feed Section Guide, right- - - - - - - - - - - - - - - - - - Presser Foot Bottom - - - - - - - - - - - - - - - - - - - - Presser Foot Feeding Section, 6 teeth per inch - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - - - - - - - - Feed Section Guide, eft - - - - - - - - - - - - - - - - - - Screw, for connecting rod hinge - - - - - - - - - - - 2 Chain Cutting Knife - - - - - - - - - - - - - - - - - - - - Connecting Rod Hinge - - - - - - - - - - - - - - - - - - - - * Not Shown on picture pate, but are components of part Nos. 56320 and 56320 U, Ref. 25 and 4 respectivey. 47 Amt. ~

2 48

Ref. Part 6405 M 2 5224 B 3 6420 W 4 6430 5 9 6 5430 F 7 22840 A 8 6430 A 9 22799 E 0 5205 A 5224 A 2 5220 A 3 9 4 5305 W 5 5324 W 6 5320 W 7 5330 Z 8 9 9 096 20 604 2 946 A 22 56330 23 56330 F 24 5330 AB 25 56330 G 26 5330 AE 27 22738 28 5330 BB 29 2256 30 5326 A 3 5324 F 32 5327 A 33 5330 M 34 9 35 22738 36 5330 P 37 594 A 38 56330 E 39 096 40 5330 R 4 6430 BT 42 56330 F 43 5330 AX FEED DOGS, THROAT PLATES, PRESSER FEET Amt. Description ~ Feed Dog, 2 teeth per inch, for Styes 56200 Land 56300 M - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate, for Styes 56200 Land 56300 M - - - - - - Presser Foot, for Styes 56200 Land 56300 M - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - Adjusting Nut - - - - - - - - - - - - - - - - - - - Adjusting Screw - - - - - - - - - - - - - - - - - - Presser Foot Bottom - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for Stye 56200 K - - - - - Throat Pate, for Stye 56200 K - - - - - - - - - - - - Presser Foot, for Stye 56200 K - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - - - - Feed Dog, 22 teeth per inch, for Stye 56300 AH - - - - Throat Pate, for Stye 56300 AH - - - - - - - - - Presser Foot, for Stye 56300 AH - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, marked AG - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - - - - Presser Foot Yieding Section - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - Feeding Section Guide - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - 2 Presser Foot Feeding Section, 22 teeth per inch- - - Screw - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 22 teeth per inch, for Stye 56300 N - - - - - Throat Pate, for Styes 56300 N, U- - - - - - - - - - - Presser Foot, for Stye 56300 N - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - 4 Feed Section Guide, eft - - - - - - - - - - - - - - Hinge Pin - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - Feed Section Guide, right - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - - - - Presser Foot Feeding Section, 22 teeth per inch - - From the ibrary of: Superior 49 Sewing Machine & Suppy LLC

34 50

FEED DOGS, THROAT PLATES, PRESSER FEET Ref. Part Description Arnt. Req. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 42 43 44 45 46 47 48 49 50 56205 56224 5320 N 87 B 74 B 5330 AK 9 5330 AL 5330 W 5330 AM 5305 W 5324 W 56320 F 56330 AB 22799 B 73 A 56330 AX 56330 AJ 56330 AG 604 52930 AC 56330 AF 5430 F 56330 AU 407 G 56330 AD 56330 AH 56330 AK 22785 22560 B 88 56330 AE 56330 AP 5305 U 9224 E 5320 J 74 A 87 A 74 B 22799 B 5330 X 5330 Y 9 5305 B 5324 B 5320 B 86 X 88 65 XD 5330 B Feed Dog, 6 teeth per inch, for Stye 56200 S - - - - - - - - - Throat Pate, for Stye 56200 S- - Presser Foot, bottom marked "5330 AL" for Stye 56200 S Screw, for chain cutting knife Chain Cutting Knife Shank - - - - - - - - - - - - - Camp Screw - - Presser Foot Bottom Spring - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - Feed Dog, 22 teeth per inch, for Styes 56300 F, R, AH - Throat Pate, for Styes 56300 F, R, AH - - - - - - Presser Foot, for Stye 56300 F- - - - - - - - Presser Foot Bottom, marked "BS" - Hinge Screw - - - - - - - - - Screw, for titing spring Titing Spring - - - - - - Hinge Pin - - - - Connecting Screw - - - - - - Screw, for chain cutting knife Chain Cutting Knife, marked "D" - - - - - - - - - Hinge Screw - - - - Nut- - - - - - Washer - - - - Locking Nut Compression Spring Pressure Reguating Nut Yoke - - - - - - - Screw Screw Screw Pr,esser Foot Link, marked "A" - - - - Bushing - - - - - - - - - - - - - Feed Dog, 2 teeth per inch, for Stye 56300 W - - Throat Pate, for Styes 56300 G and 56300 W - Presser Foot, for Stye 56300 W - - - - - - - - - Pin, for chain cutting knife - Screw, for chain cutting knife Chain Cutting Knife - - - - Hinge Screw - - - - - Presser Foot Bottom Presser Foot Shank Camp Screw - - Feed Dog, 2 teeth per inch, for Stye 56300 H - Throat Pate, for Stye 56300 H Presser Foot, for Stye 56300 H - - - - Hinge Screw Set Screw - - - - - - - - - - Presser Foot Shank - - Presser Foot Bottom - - - - 2 5

52

Ref. Part * 56320 G 2 56330 P 3 9 4 87 A 5 74 B 6 56330 T 7 22799 B 8 56330 S 9 56330 R *0 56320 B 56330 U 2 9 3 6430 BT 4 604 5 946 A 6 56330 Y 7 56330 AA 8 56330 W 9 22799 G *20 56320 C 2 56330 U 22 9 23 6430 BT 24 604 25 946 A 26 56330 Y 27 56330 AA 28 56330 X 29 22799 G *30 56320 D 3 56330 U 32 9 33 6430 BT 34 604 35 946 A 36 56330 V 37 56330 AA 38 56330 W 39 22799 G PRESSER FEET Description * Avaiabe as an extra send and charge item. Amt. ~ Presser Foot, bottom marked BM - - Presser Foot Shank - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - Chain Cutting Knife - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - 2 Hinge Screw - - - - - - - - - - - 7 - - Yieding Section - - - - - - - - - - - - - - - Presser Foot Bottom, marked Bfv - - Presser Foot - - - - - - - - - - - - - - - - - - - Presser Foot Shank - - - - - - - Camp Screw - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - 2 Yeding Section - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - Presser Foot Bottom - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - Presser Foot - - - - - - - Presser Foot Shank - - Camp Screw - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - 2 Screw - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - Presser Foot Bottom - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - Presser Foot - - - - - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - 2 Screw - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - Presser Foot Bottom - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - 53

8 54

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 AUTOMATIC CHAIN CUTTER AND PRESSURE RELEASE ATTACHMENT FOR STYLE 56300 E Part 5305 V 5324 V 56320 A 56330 H 88 HA73 B 56330 N 56330 J 6430 AJ 73 A 56330 M 56330 L 22799 R HA73 B 6430 AN 56330 K 5330 BC 660-406 5330 BO NU-2 SC-80 660-437 5330 BF SC-2 SC-78 22848 A 5330 BE 2934 A Amt. Description ~ Feed Dog, marked BN, 22 teeth per inch Throat Pate - - - - - - - - - - - - - - - - - - Presser Foot, bottom marked "AU" - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - Screw, for presser foot shank - - - - - - - Screw, for spring adjusting pin Spring Adjusting Pin - - - - - - Chain Cutter Spring - - - - - - - Spring, for presser foot bottom Screw, for spring - - - - - - - - - - - - - Yieding Section, marked "AS" - Presser Foot Bottom, marked AU Hinge Screw - - - - - - - - - - - - 2 Screw, for chain cutter Chain Cutter, marked G Adjusting Side - - - - Chain Cutter Reease Cabe - - - - - - - Stationary Cabe Camp - - - - - - - Chain Cutter Reease Cabe Casing Nut - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - Presser Bar Bushing Camp - - - - - - - - - - - Stationary Cabe Camp - - - - - - - - - - Screw - - - - - - - - - - - - - Screw - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - Peda Connection - - - - - - - - - - Nut, for cabe adjusting screw - - - - - NOTE: Automatic Chain Cutting Reease Attachment Kit 29480 GJ, consists of Ref. Nos. 7 thru 28 incusive. 2 55

56

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 42 43 44 45 46 47 48 49 50 5 Part 5305 W 5324 W 56320 H 56330 AH 56330 AD 407 G 56330 AU 5430 F 52930 AC 604 56330 AF 56330 AG 56330 AN 56330 AP 56330 AJ 56330 AX 73 A 56330 AR 604 56330 AL 22799 G 56330 AM 56330 AK 22785 22560 B 88 9705 9724 9720 9 9634 57 WD 9634 A 605 9735 5205 W 56224 A 5220 W 5230 F 9 87 B 74 B 5230 G 5405 AD-2 5405 AD-6 5424 AD-2 5424 AD-6 5420 AD-2 7420 AG-4½ 5430 D 9 5430 F 22840 A 22799 E FEED DOGS, THROAT PLATES, PRESSER FEET Description Amt. ~ Feed Dog, 22 teeth per inch, for Styes 56300 F, R, AH - - - Throat Pate, for Styes 56300 F, R, AH - - - - - - - - - - Presser Foot, for Stye 56300 R - - - - - - - - - - - - - - Pressure Reguating Nut - - - - - - - - - - - - - - - - Compression Spring - - - - - - - - - - - - - - - - - - - Locking Nut - - - - - - - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - - - - Chain Cutting Knife, marked "D" - - - - - - - - - Screw, for chain cutting knife - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - - - Connecting Screw - - - - - - - - - - - - - - - - - - - - Presser Foot Link, marked "B" - - - - - - - - - - - - - Bushing - - - - - - - - - - - - - - - - - - - - - - Hinge Pin - - - - - - - - - - - - - - - - - - - - - - - Titing Spring - - - - - - - - - - - - - - - - - Screw, for titing spring - - - - - - - - - - - - - - - Spring, for yieding section - - - - - - - - - - - - - Screw, for yieding section spring - - - - - - - - - - Presser Foot Bottom, marked "BR" - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - - - - - - Yoke - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - ~ - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for Stye 56200 R - - - - - - - Throat Pate, for Stye 56200 R - - - - - - - - - - - - - - Presser Foot, for Stye 56200 R - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - - - - - - Yieding Section Spring - - - - - - - - - - - - - - - - Screw, for yieding section spring - - - - - - - - - - - Spring Pin - - - - - - - - - - - - - - - - - - - - - - - Screw, for detachabe toe - - - - - - - - - - - - - - - 2 Detachabe Toe - - - - - - - - - - - - - - - - - - - - - Feed Dog, 2 teeth per inch, for Stye 56200 W - - - - - - - Throat Pate, for Stye 56200 W - - - - - - - - - - - - - - Presser Foot, for Stye 56200 W - - - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - - - - Screw, for chain cutting knife - - - - - - - - - - - - - Chain Cutting Knife- - - - - - - - - - - - - - - - - - - Presser Foot Bottom - - - - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for 2 gauge, Stye 56400 D - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for 6 gauge, Stye 56400 D - - - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate, for 2 gauge, Stye 56400 D - - - - - Throat Pate, for 6 gauge, Stye 56400 D - - - - - Presser Foot, for 2 gauge, Stye 56400 D - - - - - Presser Foot, for 6 gauge, Stye 56400 D - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - Adjusting Screw - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - 57

,,-:+J --- 58

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 Part 5405 A-8 5405 A-0 5424 A-6 5424 A-8 5424 A-0 5424 A-2 5420-6 5420-0 5420-2 5430 D 9 22799 B 5430 A-6 5430 A-8 5430 A-0 5430 A-2 22840 A 5430 F 5405-6 5424-6 5424-8 5420-6 5420-8 5430 D 9 22799 B 5430 A-6 5430 A-8 22840 A 5430 F 5505-8 5524-6 5524-8 5520-6 5520-8 35830 9 5930 22799 C 5530-6 5530-8 56505 56505 B 56524 A- 56524 B- 56528 C- 56528 56520 5530 D 9 22799 E 5530 G 5530.F 56530 A 9 A 52930 AC 56530 740 FEED DOGS, THROAT PLATES, PRESSER FEET Description Amt. ~ Feed Dog, 6 teeth per inch, for Nos. 6 and 8 gauges, Stye 56400 P - - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for Nos. 0 and 2 gauges, Stye 56400 P - - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate, for 6 gauge, Stye 56400 P - - - - - - - - - Throat Pate, for 8 gauge, Stye 56400 P - - - - - - - Throat Pate, for 0 gauge, Stye 56400 P - - - - - - - Throat Pate, for 2 gauge, Stye 56400 P - - - - - - - Presser Foot, for 6 gauge, Stye 56400 P - - - - Presser Foot, for 8 gauge, Stye 56400 P - - - - - - - Presser Foot, for 2 gauge, Stye 56400 P - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, for 5420-6 presser foot - - - - - Presser Foot Bottom, for 5420-8 presser foot - - - - - Presser Foot Bottom, for 5420-0 presser foot - - - - - Presser Foot Bottom, for 5420-2 presser foot - - - - - Adjusting Screw - - - - - - - - - - - - - - - - - - - - - - Adjusting Nut - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for Nos. 6 and 8 gauges, Stye 56400 P - - - - - - - - - - - - - - - - - - - - Throat Pate, for 6 gauge, Stye 56400 P - - - - - - - - - Throat Pate, for 8 gauge, Stye 56400 P - - - - - - - - - Presser Foot, for 6 gauge, Stye 56400 P - - - - - - - - - Presser Foot, for 8 gauge, Stye 56400 P - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, for 5420-6 presser foot - - - - - Presser Foot Bottom, for 5420-8 presser foot - - - - - Adjusting Screw - - - - - - - - - - - - - - - - - - - - - - Adjusting Nut- - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 2 teeth per inch, for Nos. 6 and 8 gauges, Stye 56500 J - - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate, for 6 gauge, Stye 56500 J - - - - - - Throat Pate, for 8 gauge, Stye 56500 J - - - - - - - - - Presser Foot, for 6 gauge, Stye 56500 J- - - - - - - - - - Presser Foot, for 8 gauge, Stye 56500 J- - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - - - - - Hinge Pin - - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, for 5520-6 presser foot - - - - - Presser Foot Bottom, for 5520-8 presser foot - - - - - Feed Dog, 0 teeth per inch, for 7 and 0 S.P.I., Styes 56500 B, C - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 0 teeth per inch, for 5 S.P.I., Stye 56500 A - - - - Throat Pate, for 5 S.P.I., Stye 56500 A- - - - - - - - - - - - Throat Pate, for 7 S.P.I., Stye 56500 B- - - - - - - - - - - - Throat Pate, for 0 S.P.I., Stye 56500 C - - - - - - - - - - - Insert - - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot, a stitches per inch, Styes 56500 A, B, C, U - - Presser Foot Shank - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - - - - - Punger- - - - - - - - - - - - - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - -.- - Chain Cutting Knife, Marked "D" -.- - - - - - - - - - - - - Presser Foot Bottom - - - - - - - - - - - - Pin - - - - - - - - - - - - - - - - - - - - - - - - - - - - 59

60

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 42 43 44 45 46 Part 5405 B-32 5405 B-48 5424 B-32 5424 B-48 5420 C-32 5420 C-48 5430 C-32 5430 C-48 22799 D 22752 B 77 5430 9 5405 C-48 5424 C-48 5405 K-26 5424 K-24 5424 K-26 5420 K-24 5420 K-26 5430 K-24 5430 K-26 5430 B 9 87 A 53530 E 22799 B 5505 BR-8 5524 BR-8 5520 BR-8 5530 BR-8 22799 C 35730 AC 22799 G 5530 J 35730 AD 9 73 A 35730 AE 56505 A 56528 B- 56528 56520 5530 D 9 22799 E 5530 G 5530 F 56530 A 9 A 52930 AC 56530 740 FEED DOGS, THROAT PLATES, PRESSER FEET Amt. Description ~ Feed Dog, 6 teeth per inch, for 32 gauge, Stye 56400 S - - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for 48 gauge, Stye 56400 S - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate, for 32 gauge, Stye 56400 S- - - - - - Throat Pate, for 48 gauge, Stye 56400 S- - - - - - Presser Foot, for Mo. 32 gauge, Stye 56400 S- - - - - - Presser Foot, for 48 gauge, Styes 56400 R, S - - - Presser Foot Bottom, for to. 5420 C-32 presser foot - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, for 5420 C-48 presser foot - - - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - Adjusting Screw - - - - - - - - - - - - - - - - - - Camp Screw, ower - - - - - - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - Camp Screw, upper - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for 48 gauge, Stye 56400 R - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate, for 48 gauge, Stye 56400 R- - - - - - Feed Dog, 6 teeth per inch, for Nos. 24 and 26 gauge, Stye 56400 X - - - - - - - - - - - - - - - - - - - - - Throat Pate, for to. 24 gauge, Stye 56400 X- - - Throat Pate, for tic. 26 gauge, Stye 56400 X- - - - - - Presser Foot, for 24 gauge,.stye 56400 X- - - - - - Presser Foot, for Mo. 26 gauge, Stye 56400 X- - - - - - Presser Foot Bottom, for Mo. 5420 K-24 presser foot - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, for 5420 K-26 presser foot- - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - Screw, for guide - - - - - - - - - - - - - - - - - - Guide - - - - - - - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - Feed Dog, 2 teeth per inch, for 8 gauge, Stye 56500 R - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate, for 8 gauge, Stye 56500 R- - - - - - Presser Foot, for 8 gauge, Stye 56500 R- - - - - - Presser Foot Bottom, front section - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - Hinged Section - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - 2 Presser Foot Bottom, rear section - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - - Screw, for spring - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 22 teeth per inch, for gauge, Stye 56500 U - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate, for gauge, Stye 56500 U - - - - - - Insert - - - - - - - - - - - - - - - - - - - - - - - Presser Foot, for gauge, Styes 56500 A, B, C, U - - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - Punger - - - - - - - - - - - - - - - - - - - - - - Yieding Section - - - - - - - - - - - - - - - - - - Screw, for chain cutting knife - - - - - - - - - - - Chain Cutting Knife, marked "D" - - - - - - - - - - Presser Foot Bottom - - - - - - - - Pin - - - - - - - - - - - - - - - - - - - - - - - - 6

62

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 Part 5405 R-8 5405 R-2 5424 R-8 5424 R-0 5424 R-2 5424 R-6 5420 R-8 5420 R-0 5420 R-2 5420 R-6 35730 AD 9 35730 AB 22799 G 35730 AC 22799 E 5430 R-8 5430 R-0 5430 R-2 5430 R-6 35730 AE 73 A 5405 G-8 5405 G-6 5424 E-8 5424 E-0 5424 E-2 5424 E-6 5420 E-8 5420 E-0 5420 E-2 5420 E-6 5430 D 9 22799 B 5430 E-8 5430 E-0 5430 E-2 5430 E-6 22840 A 5430 F 5905 A-7 5924 A-7 5920-7 5930 A 9 2935 A 5930 8-7 22799 B 5905 8-9 5924 8-8 5924 8-9 35820 P-8 35820 P-9 35830 9 5930 22799 C 35830 P-8 35830 P-9 FEED DOGS. THROAT PLATES. PRESSER FEET Amt. Description ~ Feed Dog. 6 teeth per inch. for Nos. 8 and 0 gauges, Stye 56400 W - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Dog. 6 teeth per inch. for Nos. 2 and 6 gauges, Stye 56400 W - - - - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate. for 8 gauge. for Stye 56400 W - Throat Pate. for 0 gauge, for Stye 56400 W - - - - - - Throat Pate, for 2 gauge. for Stye 56400 W - - - - - - Throat Pate, for 6 gauge, for Stye 56400 W - - - - - - Presser Foot. for 8 gauge, for Stye 56400 W - - - - - - Presser Foot, for 0 gauge, for Stye 56400 W - - - - - - Presser Foot, for 2 gauge, for Stye 56400 W - - - - - - Presser Foot, for 6 gauge, for Stye 56400 W - - - - - - Shank - - - - - - - - - - - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - Bottom, rear section - - - - - - - - - - - - - - - - - - - Hinge Screw, for bottom, rear section - - - - - - - - - - 2 Hinged Section - - - - - - - - - - - - - - - - - - - - - - Hinge Screw, for bottom, front section - - - - - - - - - - Bottom, front section, for 5420 R-8 presser foot - - Bottom, front section, for 5420 R-0 presser foot - - Bottom, front section, for 5420 R-2 presser foot - - Bottom, front section, for 5420 R-6 presser foot - - Spring - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 22 teeth per.inch, for Nos. 8, 0 and 2 gauges, Stye 56400 T - - - - - - - - - - - - - - - - - - - - - - - - Feed dog, 22 teeth per inch for 6 gauge. Stye 56400 T- - Throat Pate, for 8 gauge, for Stye 56400 T - - - - - - Throat Pate, for 0 gauge, for Stye 56400 T - - - - - - Throat Pate, for 2 gauge, for Stye 56400 T - - - - - - Throat Pate, for 6 gauge, for Stye 56400 T - - - - - - Presser Foot, for 8 gauge, for Stye 56400 T - - - - - - Presser Foot, for 0 gauge, for Stye 56400 T - - - - - - Presser Foot, for 2 gauge, for Stye 56400 T - - - - - - Presser Foot, for 6 gauge. for Stye 56400 T Shank - - - - - - - - - - - - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, for 5420 E-8 presser foot - - - Presser Foot Bottom, for 5420 E-0 presser foot - - - Presser Foot Bottom, for 5420 E-2 presser foot - - - Presser Foot Bottom, for 5420 E-6 presser foot - - - Screw, for adjusting tit of presser foot - - - - - - - - Nut - - - - - - - - - - - - - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for 7 gauge, Stye 56900 H - Throat Pate, for 7 gauge, for Stye 56900 H - - - - - - - Presser Foot, for 7 gauge, for Stye 56900 H - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - - - - - Adjusting Screw - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom - - - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - - - - Feed Dog. 0 teeth per inch, for Nos. 8 and 9 gauges, Stye 56900 H - - - - - - - - - - - - - - - - - - - - - - - - - - - Throat Pate, for 8 gauge, for Stye 56900 H - - - - - - - Throat Pate, for 9 gauge. for Stye 56900 H - - - - - - - Presser Foot, for 8 gauge, for Stye 56900 H - - - - - - - Presser Foot, for 9 gauge, for Stye 56900 H - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - - - - - Camp Screw - - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, for 35820 P-8 presser foot Presser Foot Bottom, for 35820 P-9 presser foot - - - 63

64

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 42 Part 5705-64 5705-56 5724-64 5724-56 5720-64 5720-56 5430 9 77 22752 B 22799 D 5730 A-64 5730 A-56 9 A 5730-64 5730-56 5905 E-9 5924 E-9 35820 S-9 22799 L 35830 F 2256 D 35830 D 35830 B 9 D 73 A 35830 H 22845 A 22599 35830 K 35830 C 35830 S-9 35830 AE 35830 J 56905 A-9 56924 A-9 56920 A-9 35830 B 9 D 73 A 35830 H 22845 A 22599 35830 K 35830 C 35830 R-9 56930 FEED DOGS, THROAT PLATES, PRESSER FEET Amt. Description ~ Feed Dog, 6 teeth per inch, for 64 gauge, Stye 56700 J - - - - - - - - - - - - - - - - - - Feed Dog, 6 teeth per inch, for 56 gauge, Stye 56700 J - - - - - - - - - - - - - - - - - - Throat Pate, for 64 gauge, Stye 56700 J- - - Throat Pate, for 56 gauge, Stye 56700 J- - - Presser Foot, for 64 gauge, Stye 56700 J- - - Presser Foot, for 56 gauge, Stye 56700 J- - - Presser Foot Shank - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - Camp Screw, ower - - - - - - - - - - - - - - Adjusting Screw - - - - - - - - - - - - - - - Hinge Screw - - - - - - - - - - - - - - - - - Fexibe Toe, for 5720-64 presser foot - Fexibe Toe, for 5720-56 presser foot - Screw - - - - - - - - - - - - - - - - - - - - 2 Presser Foot Bottom, for 5720-64 presser foot - - - - - - - - - - - - - - - - Presser Foot Bottom, for 5720-56 presser foot - - - - - - - - - - - - - - - - Feed Dog, 0 teeth per inch, for 9 gauge, Stye 56900 R - - - - - - - - - - - - - - - - - - Throat Pate, for 9 gauge, Stye 56900 R - - - Presser Foot, for 9 gauge, Stye 56900 R - - - Hinge Screw- - - - - - - - - - - - - - - - - - Adjusting Nut- - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - Presser Foot Shank - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - 6 Screw- - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - Yoke - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, front section - - - - - - Yieding Section - - - - - - - - - - - - - - - Presser Foot Bottom, rear section- - - - - - - Feed Dog, 0 teeth per inch, for 9 gauge, Styes 56900 J, P - - - - - - - - - - - - - - - - Throat Pate, for 9 gauge, Styes 56900 J, P - Presser Foot, for 9 gauge, Styes 56900 J, P - Presser Foot Shank - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - Screw- - - - - - - - - - - - - - - - - - - - - 6 Screw- - - - - - - - - - - - - - - - - - - - - Spring - - - - - - - - - - - - - - - - - - - - Yoke - - - - - - - - - - - - - - - - - - - - - Presser Foot Bottom, front section - - - - - - Presser Foot Bottom, rear section- - - - - - - 65

I I ' 66

Ref. 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 Part 2300 23425 V 25 C 23425 V 23405 J 22548 9255 23435-32 23435-48 23436 36 282 N 282 P 26 B 56392 E 282 L 282 K 0-3 39592 AK 39592 Z ATTACHMENTS, BRACKETS AND STRIP TENSION Description Doube Edge Foder and Guide, 3/64 inch capacity, 3/6 inch overap, for Styes 56200 R - - - - - - - - - - Washer Pate - - - - - - - - - - - - - - - - - - - - - Screw, for attachment - - - - - - - - - - - - - - - - Washer Pate - - - - - - - - - - - - - - - - - - - - Amt. ~ - - 2 Body Foder, for turning body of garment downwardy, /32 inch capacity, 5/6 inch fod, for Stye 56400 S - - - - - - Screw, for facing strip foder - - - - - - - - - - - - - - - - Washer - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Facing Strip Foder, for shirt front operations, /32 inch capacity, uses strip inch wide, finishes 5/8 inch, for 32 gauge, Stye 56400 S - - - - - - - - - - - - - - - Facing Strip Foder, for shirt front operations, /32 inch capacity, uses strip /4 inch wide, finishes 7/8 inch, for 48 gauge, Stye 56400 S - - - - - - - Foder Bracket, for Stye 56400 S - - - - Screw, for foder bracket - - - - - - - - - - - - 2 Strip Tension, for Stye 56400 S - - - - - - - Strip Tension Base - - - - - - - - - - - - - - - - - - - - Tension Post Ferrue - - - - - - - - - 2 Tension Post - - - - - - - - - - - - - - - - - - - - - 2 Strip Tension Pate, inner - - - - - - Strip Tension Pate, outer - - - - - - - - - - Tension Spring - - - - - - - - - - - - - - Tension Nut Ferrue Tension Nut- - - - - - - - - - 2-2 - 2 67

3 68

Ref..J:!Q..,_ + - * 2 * 3 * 4 5 * 6 * 7 * 8 * 9 *0 * *2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 Part 2340 K-64 2340 K-56 2340-K-48 K58337 22528 23229 P 23229 N 22572 A 22773 23229 Y 25 T 23229 Q 22863 A 25 cc 25 S 25 8 23403-64 23403-56 23403-48 25 C 23405 L 23425 V 28 23425 V 28 23425 V 235 A 2385 8 278 0-3 20 C 20 A 220 660-240 6 2388 660-264 42 D-34 5295 A 5295 8 SC303 269 F 6 88 269 E Assemby Ref. 8 23420 U-6-/32 23420 U-8-/32 23420 U-0-/32 23420 U-2-/6 23420 U-6-/6 23420 U-6-3/32 23420 U-8-/6 23420 U-8-3/32 +23420 U-8- /8 23420 U-26-/6 23420 V-8-/32 23420 V-0-/32 23420 V-2-/32 23420 V-6-/32 - ATTACHMENTS, TAPE REEL AND MISCELLANEOUS ACCESSORIES Description Center Pait Foder, /32 inch capacity pait extends /4 inch beyond rows of stitches, uses pait cut 2 /2 inches wide, finishes /2 inches; interining strip cut 5/32 inches wide, for 64 gauge, for Styes 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Center Pait Foder, /32 inch capacity, pait extends /4 inch beyond rows of stitches, uses pait cut 2 3/8 inches wide, finishes 3/8 inches; interining strip cut /32 inches wide, for 56 gauge, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Center Pait Foder, /32 inch capacity, pait extends /4 inch beyond rows of stitches, uses pait cut 2 /4 inches wide, finishes /4 inches; interining strip cut 7/32 inches wide, for 48 gauge, for Stye 56400 R - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Center Pait Foder, /6 inch capacity, pait extends /4 inch beyond rows of stitches, uses pait cut 2 /2 inches wide, finishes /2 inches; interining strip cut 7/6 inches wide, for 64 gauge, for Stye 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Foder Bracket, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - Foder Swinging Ann, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Foder Swinging Ann Support, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Foder Camp, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Adjusting Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Anguar Interining Guide, reversibe, for 64 gauge, Stye 56700 J - - - - - - - - - - - - - - Anguar Interining Guide, reversibe, for 56 gauge, Stye 56700 J - - - - - - - - - - - - - - Anguar Interining Guide, reversibe, for 48 gauge, Stye 56400 R - - - - - - - - - - - - - - Screw, for Styes 56200 K, R, 56500 J, R, 56700 J, Cass 56400 and 56900 - - - - - - - - - - - - - 2 Body Foder, for turning body of gannent upwardy, /32 inch capacity, 5/6 inch fod, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Washer Pate - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Doube Lap Seam Feer Assemby (See Chart Beow) - - - - - - - - - - - - - - - - - - - - - - - - - Lower Scro and Base (See Chart Beow) - - - - - - - - - - - - - - - - - - - - - - - - - - - - Upper Scro (See Chart Beow) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - Washer Pate - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screw, for Ref. 20 on Styes 56900 P-9, R-9 (not shown) - - - - - - - - - - - - - - - - - - - - Washer Pate, for Styes 56900 P-9, R-9 (not shown) - - - - - - - - - - - - - - - - - - - - - - - - Pate Foder and Guide, for heavy materias, /4 inch capacity for both pies, top py foded, ower py fat, /2 inch overap, for Stye 56900 J- - - - - - - - - - - - - - - - - - - - - - - - Tape Ree Axe, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - Tape Ree Disc, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Tape Ree Spring, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - Tape Ree Axe Screw, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - Tape Ree Frame, for Styes 56400 R, 56700 J - - - - - - - - - - - - - - - - - - - - - - - - - - - Screwdriver, 9/64 inch round bade, ength overa 7 /6 inches, for Casses 5640D, 56500, 56700, 56900- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Thread Tweezers, for a Styes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Wrench, 9/32 inch open end, for Casses 56200, 56300 - - - - - - - - - - - - - - - - - - - - - - - Wrench, 3/8 inch open end, for a Styes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - "S" Hook, for a Styes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Treade Chain, 34 inches ong, for a Styes - - - - - - - - - - - - - - - - - - - - - - - - - - - Isoator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Isoator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Wood Screw, P2, inch ong, for Styes 56200 K, L, 56300 M - - - - - - - - - - - - - - - - - - - 2 Binding Hoder Base, for Styes 56200 K, L, 56300 M - - - - - - - - - - - - - - - - - - - - - - - - Binding Hoder Stop Coar, for Styes 56200 K, L, 56300 M - - - - - - - - - - - - - - - - - - - - Screw - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Binding Hoder Disc, for Styes 56200 K, L, 56300 M - - - - - - - - - - - - - - - - - - - - - - - - DOUBLE LAP SEAM FELLER Lower Scro Upper Scro Ref. 9 Ref. 20 Gauge Capacity For. Machine Stye 23422 U-/32 2342 U-6-/32 6 /32" 56400 P-6 23422 U-/32 2342 U-8-/32 8 /32" 56400 P-8, W-8 23422 U- /32 2342 U-0-/32 0 /32" 56400 P-0, W-0 23422 U-/6 2342 U-2-/6 2 /6" 56400 P-2, W-2 23422 U- /6 2342 U-6-/6 6 /6" 56400 P-6, W-6 23422 U-3/32 2342 U-6-3/32 6 3/32" 56500 J-6, 56900 H-7, H-8 23422 u- /6 2342 U-8-/6 8 /6" 5640D P-8 23422 U-3/32 2342 U-8-3/32 8 3/32" 56500 J-8, R-8, 56900 H-9 23422 U-/8 2342 U-8-/8 8 /8" - 23422 u- /6 2342 U-26-/6 26 /6" 56400 X-26 23422 V-/32 2342 V-8-/32 8 /32" 56400 T-8 23422 V-/32 2342 V-0-/32 0 /32" 56400 T-0 23422 V-/32 2342 V-2-/32 2 /32" 56400 T-2 23422 V-/32 2342 V-6-/32 6 /32" 56400 T-6 23422 BZ-3/32 2342 U-8-3/32 9 3/32" 56900 P-9 23422 BZ-/8 2342 U-8-/8 9 /8" 56900 R-9 + Avaiabe as an extra send and charge item or on specia machines. * Avaiabe compete as part 2948 D (Suspended Foder Ann Assemby). Amt. ~ 69

20 8 70

THREAD STAND PARTS Amount Required Ref. Part One Two Three Description Neede Neede Neede 20 H-2 Thread Stand, compete, for Casses 56200, 56300 - - - - 2 20 H-4 Thread Stand, compete, for Casses 56400, 56500, 56700-3 20 H-6 Thread Stand, compete, for Cass 56900 - - - - - - - - 4 204 B-2L!- Thread Stand Rod - - - - 5 204 H Nut - - - - - - - - - - - 6 652-6 Washer - - - - - - - - - 7 24 U Lead Eyeet Ba Spit Socket - - - - - - - - - 2 2 2 8 24 A Thread Stand Base - - - - 9 2265 CD-4 Screw - - - - - - - - 0 2280 Screw - - - - - - - - - - 24 T Lead Eyeet Socket Ba - 2 2265 CD-4 Screw - - - - - - - - 3 204 V Pad, for thread cone- - - 2 4 6 4 24 W Spoo Pin - - - - - - - - 2 4 6 5 258 A Nut - - - - - - - - - - - 4 8 2 6 24 Spoo Seat Disc - - - - - 2 4 6 7 652-6 Washer- - - - - - - - - - 2 4 6 8 24 H-2 Eyeet Support - - - - - 9 24 H-4 Eyeet Support - - - - - 20 24 H-6 Eyeet Support - - - - - 2 2265 CD-4 Screw - - - - - - - - 2 2 2 22 24 D-2 Spoo Seat Support- - - - 23 24 D-4 Spoo Seat Support- - - - 24 24 D-6 Spoo Seat Support- - - - 25 2265 CD-5 Screw - - - - - - - - 2 2 2 26 24 S-2 Lead Eyeet - - - - - - - 27 24 S-4 Lead Eyeet - - - - - - - 28 24 S-6 Lead Eyeet - - - - - - - 7

Part Page ~ SC2....... 55 W03.......... 29,3 NU2......... 55 8......... 3 20......... 25,3,35 CL2......... 29 24.......... 4 24 s... 4 25........... 4 25 8... 69 25 c... 4,67,69 25 s... 69 25 T... 69 25 cc... 69 25 TB 4 27-435 Bk... 29 28......... 35,47,69 50-26 Bk.... 35 50-458 Bk... 3 50-895 Bk...... 27 50 J... 43 52 A... 25 56......... 29,43 57 WB... 25 57 WD....... 25,57 65 XD....... 5 C067 D....... 39 C067 E......... 3 73........ 3,45 73 A... 45,5,55, 57,6,63, 65 HA73 B......... 55 77....... 29,33,6, 65 86 x....... 5 87........ 25 87 u... 3,47 88......... 3,5,55, 57,69 88 8... 43 89......... 43 90.......... 27,4 9...... 47,49,5, 53,57,59, 6,63,65 9 A.......... 59,6,65 9 D 65 95......... 25,29 96...... 3 98.......... 3,33,43 98 A........... 25,35 09..... 37 0-3....... 67,69 6....... 69 36.......... 67 58 A... 25 58 8... 35 6........... 69 SC78...... 55 SC80........... 55 87 A........ 5,53,6 87 B... 43,47,5, 57 20 A......... 69 Part NUMERICAL INDEX OF PARTS 20 c... 69 Page ~ 258 A......... 3,33,7 269......... 3,33 SC303........ 69 402........ 39 42 D-34....... 69 53....... 39 539....... 25 604... 47,49,5, 53,57 605....... 57 605 A... 25,43 652-6......... 7 660-73........ 25 660-74........ 25 660-75......... 25 660-202.......... 29 660-207...... 39 660-25....... 29 660-22....... 27 660-240........ 69 660-264........ 69 660-269 8... 33 660-30........ 3 660-33... 25 660-342... 25 660-406...... 55 660-437......... 55 660-438..... 33 660-455...... 27 660-64..... 29 660-67......... 25 660-625....... 29 660-665......... 27,29 666-49......... 33 666-24... 25 666-259..... 27 79.......... 3 096.......... 47,49 280............. 3 594 A........ 47,49 740... 59,6 74 A........ 5 74 8 47,5,53, 57 6042 A... 33 6405 M... 49 6420 w... 49 6430............ 49 6430 A... 49 708 E-5... 43 7040-6......... 43 7420 AG-4 /2... 57 7947......... 25 9205 E......... 47 9224 E....... 47,49 9255......... 67 9634.......... 57 9634 A......... 57 9705........... 57 9720........ 57 9724........ 57 9735........... 57 26 8... 67 635 8...... 27 Part ~ 638 M... 25 2934 A......... 29,55 2935 A... 63 2957 E......... 4 4077......... 3 5438 c... 25 5465 F 3 946 A......... 47,49,53 20 H......... 7 204 B-24....... 7 204 H... 7 204 v......... 7 24......... 7 24 A........... 7 24 D..... 7 24 H... 7 24 s... 7 24 T... 7 24 u... 7 24 ~,... 7 269 E....... 69 269 F. 69 278......... 69 282 K 67 282 L.......... 67 282 N........... 67 282 P............ 67 220.......... 69 220...... 45 220 A......... 45 2375 AV.......... 25 2385 8...... 69 2388.......... 69 2396 AG... 25 2396 AL.......... 25 2396 BK... 25 2396 BP....... 25 2396 BR........ 25 2657-3......... 37 2657-4........... 37 Page.J!Q.:_ 2657 E........... 33,35,4 2657 w... 39 2657 x........... 27 2657 v........ 39 2253............. 25 2253 8... 43 22524.......... 25 22525 A.......... 33 22526 c... 4 22528....... 33,35,69 22537.......... 39 22539 R...... 27 2254 c... 27 22543 A........... 33 22548......... 25,67 22557 G.......... 39 22559 A... 29 22559 G... 29 22560 B......... 5,57 2256............... 47,49 2256 D... 65 22562 A.......... 29 22564.......... 29 22569 8... 25,27 22569 c... 25 NOTE: Ony the basic part numbers are shown in the index. For various gauges, capacities, etc. avaiabe, refer to the istings on pages indicated. 72

Part 22570......... 25 22572 A...... 69 22574....... 29 22580....... 43 22580 D 33 22585.......... 25,4 22585 A......... 25 22586 R....... 29 22587 K........ 29 22596........... 39 22598 c... 37 22599..... 65 Page.J!Q.:_ 22637 P-24..... 33 2265 CB-4...... 33 2265 CD......... 33,7 22653 L-8....... 29 22729....... 43 22729 C......... 3 22733 c... 25 22733 E........ 27 22735....... 4 22738........ 47, 49 22743....... 43 22752......... 43 22752 8... 6,65 22758 c... 39 22758 G........ 47 22760 A....... 4 22764 C.......... 33 22768......... 29,35 22773...... 69 22785........ 5,57 22793.......... 27 22798 c... 33 22799 8... 5,53,59, 6,63 22799 C....... 59,6,63 22799 0........ 6,65 22799 E. 49,57,59, 6,63 22799 G........ 53,57,6, 63 22799 L........ 65 22799 R......... 55 2280........ 33,43 2280....... 7 22829........ 25,3 22834 A...... 33 22835....... 3 22836........ 25 22837..... 35 22839........ 25 22839 C....... 4 22840 A....... 49,57,59, 63 22840 C..... 39 22845 A...... 65 22845 8.... 4 22848..... 25,35 22848 A...... 55 22863 A.... 69 22863 C.... 33 22874......... 3 22875 H......... 33 22875 J..... 47 Part.J!Q.:_ NUMERICAL INDEX OF PARTS 22882 C....... 3 22889 A.. 25 2289 8.... 33 22894 C..... 29 22894 D 29 22894 E... 25 22894 J...... 29 22894 P...... 43 22894 AA 33 22894 AB....... 29 2300..... 67 235 A.... 69 2325 BG..... 4 23229 N......... 69 23229 P........ 69 23229 Q 69 23229 V 69 23322 AB...... 4 23322 AC....... 4 2340 K....... 69 23403....... 69 23405 J........... 67 23405 L......... 69 23420 u... 69 23420 V........ 69 2342 u... 69 2342 V..... 69 23422 u... 69 23422 V...... 69 23422 BZ.......... 69 Page.J!Q.:_ 23425 T 4 23425 V........ 4,67,69 23435..... 67 23436............ 67 23437 8 4 23437 V 4 23438 A...... 4 23438 8....... 4 23439 A........ 4 29066 R........ 29 2905 AK......... 29 2905 AL..... 29 2992 v......... 3 2992 w 3 2992 X 3 2992 v........ 3 2992 AA 3 29202 L-.......... 43 29202 M-....... 43 29202 N-....... 43 29348 AF...... 29 29476 LL....... 29 29476 LM..... 29 29476 LN...... 29 29476 LV..... 3 29476 MJ..... 33 29476 MY...... 35 29476 NM..... 33 35730 AB...... 63 35730 AC... 6,63 35730 A0....... 6,63 35730 AE....... 6,63 3573 A......... 25 35772 H..... 4 3588 N....... 43 Part.J!Q.:_ 35820 P....... 63 35820 S-9.... 65 35830......... 59,63 35830 8........ 65 35830 c... 65 35830 o........ 65 35830 F...... 65 35830 H 65 35830 J...... 65 35830 K........ 65 35830 P............ 63 35830 R-9......... 65 35830 S-9...... 65 35830 AE.......... 65 35897 BV......... 27 39543 N......... 33 39552 c... 39 39592 z...... 37,67 39592 AK....... 37,67 4047........ 3 407 G....... 5,57 439........ 33 43266......... 37 43296......... 25 5054......... 33 554 E........ 27 570 o........ 3 5205 A....... 49 5205 R............ 47 5205 w 57 5208........... 45 5208 o........ 45 5208 w 45 520........... 45 526 M.......... 29 526 N......... 29,3 526 P....... 29 527 C..... 43 5220 A...... 49 5220 w... 57 5224 A.... 49 5224 8 49 5230 F......... 57 5230 G....... 57 5236 A........ 3,33 5240 o...... 3 5242 M....... 3 5244 L..... 3 5244 N........ 3 5246........... 3 5247....... 29 5250 o..... 29 5250 F....... 29 5254 K......... 29 5256 c... 39 5257 K........ 39 5257 M....... 39 5257 AA 27 5270 8... 25 5280 J......... 25 528 AC........ 4 5283 H........ 39 5292 A..... 37 5292 D........ 37 5292 F........ 37 NOTE: Ony the basic part numbers are shown in the index. For various gauges, capacities, etc. avaiabe, refer to the istings on pages indicated. Page.J!Q.:_ 73

Part ~ Page ~ 5294 R..... 25 5295 A... 69 5295 B 69 5305 8... 5 5305 u...... 5 5305 v......... 55 5305 w......... 49,5,57 5320 B. 5 5320 J....... 5 5320 M..... 47 5320 N 5 5320 w 49 5324 8...... 5 5324 F. 47,49 5324 K...... 47 5324 v........ 55 5324 w... 49,5,57 5326 A...... 49 5327 A.... 49 5330 8....... 5 5330 M 47,49 5330 N 47 5330 P 47,49 5330 R.... 47,49 5330 s... 47 Part NUMERICAL INDEX OF PARTS 5420.... 59 5420 c... 6 5420 E..... 63 5420 K........ 6 5420 R......... 63 5420 A0-2......... 57 5424........... 59 5424 A......... 59 5424 8....... 6 5424 C-48...... 6 5424 E......... 63 5424 K... 6 5424 R......... 63 5424 A0...... 57 5430......... 6,65 5430 A....... 59 5430 B... 6 5430 c... 6 Page 5430 D.......... 57,59,63 5430 E.... 63 5430 F 39,49,5, 57,59,63 5430 K... 6 5430 R..... 63 5457 A......... 35 Part ~ 5905 8-9....... 63 5905 E-9....... 65 5908 B... 45 5909 c... 45 5909 D.... 45 597 A.......... 43 598-7....... 43 5920-7........... 63 5924 A-7........ 63 5924 B... 63 5924 E-9......... 65 5930......... 59,63 5930 A... 63 5930 8-7......... 63 5957 o.......... 39 5957 E.... 39 5959 B... 35 5959 0......... 35 5959 J....... 35 5959 K........ 35 5992 A......... 37 52336 A..... 29 52804 A........... 35 52889 A....... 39 52892.......... 37 5330 w 47,5 5459 A........ 35 52930 AC......... 5,57,59, 6 52942 R...... 3 52942 w... 27 5330 x 5 5330 Y...... 5 5330 z.... 47,49 5330 AB.... 47,49 5330 AD... 47 5330 AE... 47,49 5330 AG... 47 5330 AH... 47 5330 AJ........ 47 5330 AK....... 5 5330 AL....... 5 5330 AM..... 5 5330 AX... 49 5330 BB 49 5330 BC...... 55 5330 BO... 55 5330 BE......... 55 5330 BF......... 55 5334 A..... 47 5334 C... 47 5334 o... 47 5405-6... 59 5405 A.... 59 5405 B..... 6 5405 C-48.. 6 5405 G.... 63 5405 K-26... 6 5405 R... 63 5405 AD... 57 5408..... 45 5409....... 45 5409 B... 45 5409 C 45 547 c... 43 547 D.... 43 548-6... 43 548 8-32..... 43 548 0-48.. 43 548 K 43 549 c... 37 5492...... 35 5505-8.... 59 5505 BR-8........ 6 5508 C-.... 45 5508 G-... 45 5508 H-...... 45 5508 M........ 45 5509 C...... 45 558 C-.... 43 558 G-.... 43 5520....... 59 5520 BR-8.... 6 5524...... 59 5524 BR-8.... 6 5530.... 59 5530 D.......... 59,6 5530 F... 59,6 5530 G....... 59,6 5530 J.... 6 5530 BR-8.... 6 5557....... 35 5704........ 35 5705....... 65 5708... 45 5709........ 45 577..... 43 578 A.. 43 578 8..... 43 5720..... 65 5724........ 65 5730........ 65 5730 A....... 65 5745.. 3 5757 8.... 35 5758....... 25 5770... 3 577...... 3 5905 A-7.. 63 52942 AA.......... 29 52942 AC........ 27,29 52958 B......... 25 52958 G........... 25 53530 E... 6 53783 N... 39 53787......... 39 55235 o........... 33 55235 E......... 33 55244 G... 3 5622 A........ 33 5690........ 27 56205.......... 5 56224...... 5 56224 A...... 57 56224 H... 47 5630......... 4 5630 A........... 4 56304....... 35 56305......... 47 56305 AL......... 47 5633.......... 3 5635 A......... 29 5636......... 29 5636 C... 29 56320......... 47 56320 A...... 55 56320 B.... 53 56320 C.......... 53 56320 D........ 53 56320 F......... 5 56320 G...... 53 56320 H........ 57 56320 u... 47 5632 o......... 29 5632 N... 29 NOTE: Ony the basic part numbers are shown in the index. For various gauges, capacities, etc. avaiabe, refer to the istings on pages indicated. Page 74

Part 56322 B...... 33 56322 C........... 33 56323......... 33 56324 AL.. 47 56325....... 43 56330.......... 47,49 56330 E........ 47,49 56330 F....... 47,49 56330 G.......... 47,49 56330 H...... 55 56330 J.......... 55 56330 K........ 55 56330 L........ 55 56330 M......... 55 56330 N....... 55 56330 P......... 53 56330 R...... 53 56330 s..... 53 56330 T... 53 56330 u......... 53 56330 V. 53 56330 w.......... 53 56330 x............. 53 56330 v......... 53 56330 AA........... 53 56330 AB........... 5 56330 AD........... 5,57 56330 AE........... 5 56330 AF........... 5, 57 56330 AG....... 5, 57 56330 AH........ 5, 57 56330 AJ........... 5,57 56330 AK.... 5,57 56330 AL....... 57 56330 AM........... 57 56330 AN... 57 56330 AP........ 5, 57 56330 AR............ 57 56330 AU........ 5, 57 56330 AX.......... 5,57 56334 B....... 33 56334 F........... 47 56334 L.......... 33 56334 N...... 33 56334 P.............. 33 56335 D........ 33 56335 G.......... 33 56335 L......... 33 56336......... 33 56336 B............. 33 56336 C.......... 33 56336 D......... 33 5634 E............. 3 5634 F......... 3 5634 G..... 3 5634 M............. 3 56342 D......... 27 56342 E.............. 29,3 56343 c............ 29 56343 E........ 29 56343 F....... 29 56344........ 3 56344 B....... 3 56344 C...... 3 56350 D...... 29 56350 E....... 29 NOTE: Page ~ Part ~ NUMERICAL INDEX OF PARTS 56350 F............ 29 56350 G.............. 29 56354 c.............. 27 56354 o............ 29 56356............... 39 56357 A........... 39 56358............... 29 56358 A............ 29 56358 B............... 35 56358 C............ 35 56358 D................ 35 56358 E............. 35 56370.......... 25 56380............... 25 5638........... 4 5638 C-207........... 4 5638 E-207............ 4 56382.............. 25 56382 B................. 27 56382 c......... 27 56382 D................ 25 56382 E......... 25 56382 G................. 25 56382 H................. 25 56382 J................ 25 56382 K........... 25 56382 L................. 25 56382 M................. 27 56382 N............ 25 56382 X............. 37 56382 Y............. 25 56382 AA.............. 25 56382 AB.............. 25 56382 AC............ 27 56383 A......... 39 56383 D........... 39 56383 AA.............. 39 56383 AB............ 39 56390............ 27 56390 E........ 27 56390 G............ 27 56390 H............. 27,29 56390 J....... 27,29 5639............ 25 56392 E... 37,67 56392 F................ 37 56393 c.......... 25 56393 D.............. 25 56393 J.......... 3 56393 L................ 27 56393 P............ 27 56393 Q............ 27 56393 T................ 27 56393 w 27 56394 A............ 27 56394 B............. 27 56394 C........... 27 5640........ 4 5643.............. 3 56423............. 33 56425............. 43 56458.......... 29 56458 A........... 29 56470............. 25 56480.......... 25 56505......... 59 Page Part Page ~ ~ 56505 A........... 6 56505 B................ 59 5653................... 3 5657 B.................. 43 5657 c-.............. 43 5657 0-............. 43 5657 E-............. 43 5658 C-................ 43 56520.................. 59, 6 56524 A-.............. 59 56524 B-........ 59 56525................. 43 56525 A.............. 43 56525 8................. 43 56525 C............. 43 56528.................... 59,6 56528 B-............. 6 56528 C-............... 59 56530................... 59,6 56530 A................. 59,6 5670.............. 4 5673................... 3 56722 E.............. 33 56723................. 33 56725.......... 43 56744.............. 3 56744 A....... 3 5675................... 3 56772............... 3 56782................... 25 56905 A- 9................. 65 5693.................... 3 5693 A................ 3 5697................. 43 56920 A-9.............. 65 56924 A-9.............. 65 56925................. 43 56930................ 65 56958................... 29 56958 A............... 29 56958 8.............. 25 57835 8................. 27 57840.............. 3 5784.......... 3 5784 A................... 3 57842 B.................. 27 57847.................. 29 57890 B................. 27 57954.................. 27 K58337................. 69 59292.................. 37 59292 A.............. 37 59493 A................... 25 6256 G......... 27 632 L................. 29 634 J............... 33 6430 AJ............ 55 6430 AN.... 55 6430 BT.............. 47, 49,53 6434 G.......... 33 63494 F............... 27 63494 G............ 27 63494 K.................. 27 80557................ 37 Ony the basic part numbers are shown in the index. For various gauges, capaci t ies, etc. avaiabe, refer to the istings on pages indicated. 75

WORLDWIDE SALES AND SERVICE Union Specia Corporation maintains saes and service faciities throughout the word. These offices wi aid you in the seection of the right sewing equipment for your particuar operation. Union Specia Corporation representatives and servicemen are factory trained and are abe to serve your needs prompty and efficienty. Whatever your ocation, there is a Union Specia Corporation representative to serve you. Check with him toq_ay. It is important to remember that LEWIS and COLUMBIA machines are aso products of Union Specia Corporation, thus offering the industry the most compete ine of the Finest Quaity sewing machines. Norcross. GA Chicago. IL Daas, TX Commerce. CA New York, NY Phiadephia, PA Woburn, MA Opa-ocka, FL Montrea, Quebec Toronto. Ontario Catano, Puerto Rico Brusses, Begium Leicester, Engand Paris, France Stuttgart, W. Germany Hong Kong Other Representatives throughout a parts of the word Union Spec ia Corporation, 400 N Franki n Street. Chicago, IL 6060, U S A Union Specia, GmbH, Schwabstrasse 33 0-7000 Stutgart We-;I G rma y Pnnred in U S A