All of these configurations are from one 2005 Blue Ultralite Trayman. Just slide the straps up and over your shoulders and they will slip into place.

All of these configurations are from one 2005 Blue Ultralite Trayman. Just slide the straps up and over your shoulders and they will slip into place.

The back edge of the Shoulder Strap has a slight bend outward That allows the Trayman to slide easily on and off. To Remove the Trayman simply tilt the unit off from your midriff with one easy motion.

The Right Strap,as you wear the Trayman, has the longer Safety Stop The Right Chest bar is the thicker of the two Chest Bars at it s end. Insert the Right Strap into the Right Chest Bar. Next slip on one nylon washer and then tighten the Quick Grip knob that was originally on the Strap when you opened up the Strap s Shipping Bag. After slipping the Trayman onto your shoulders hand tighten the knobs for both the right and left straps.

Repeat the same insert and tightening of the second Quick Grip Knob to the Left Shoulder Strap and Left Cross Bar. Remember the Left Cross Bar is thinner at it s end then the Right Cross Bar is. The Shoulder Strap Stops allow the Straps to extend from 90 to 45 degrees safely. This will allow you to adjust the Strap to the best angle for your shoulders.

The Shoulder Straps are attached using hardened steel 10/32 Button Head Allen Bolts that are secured with Red Lock-Tite. The relief pattern will allow the Straps to be bent one time to shorten the strap for some women. You may wish to bend the arc of the strap slightly as well to fit yourself. First remove the Straps and adjust them a little bit at a time. Your Trayman is made from 6061 Aircraft Quality Aluminum which is very strong, however multiple adjustments of the Straps Arc is not recommended

The Center Wave Grip is a combination of a Sure Grip Knob and 10/32 hardened steel Thread, one Nylon Washer, and The Center Wave Grip itself. This allows the Left and Right Upper Chest Bars to be quickly opened and closed as desired, and allow for a wide range of chest and shoulder sizes. The Wave Grips are cut from Billet 6061 Aluminum stock.

The Center Wave grip being adjusted from it's narrowest to widest positions.

The use of the Lower Wave Grip is similar to the Center Wave Grip in all it s operation and adjustments.

This is one of the reasons no accessories are needed, even if you are a very tall person, or a individual with a very long reach. The Trayman has a incredible range of adjustability crafted into it s design.

The Upper Spine is totally removable allowing the overall length to be even shorter then the Lower Wave Grip allows for. Simply remove the Upper Spine Bar and attach the Upper Wave Grip and Chest Bars to The Lower Spine Bar. It will help if you keep the unneeded parts assembled as shown for use later on.

Machined out of 6061 Billet Aluminum the Fast Lock Tray Swivel will lock down with a sure grip supported by it s hardened steel pivot shaft also secured, as are all hard points, with Red Lock-Tite.

The CNC Machined Timed Wave Pattern allows you to find just the right angle of tilt for the trays. Your individual sweet spot will be exactly where you are most comfortable. The Sure Grip brass lined knob only needs to be twisted open to adjust the angle of the Trayman Tables. A Nylon release washer guards against over tightening the mechanism via a strong pair of hands or too much enthusiasm.

The two Tray Support Spines are made so that each Tray may touch or slide away from each other. This side to side travel extends as far as the end of each slot that has been milled into the Lower Cross Bar. The two Tray Spines allow the Trays to slide away from or towards the user.

The Trayman Tables have been rotated up vertically and locked into place so that you can clearly see the underside of the Tables. This exposes the two Tray Spines and the four smaller Quick Grip Knobs that both secure the Trays and allow them to be repositioned. Just loosen each pair of Knobs and slide the Tray into whatever position best fits your transmitter. Please note that the Trayman Tables maybe rotated into any position or relationship to one another. There is a great number of Tray combinations that are possible. The Bungee Cord in the center has been attached in a typical four Bungee-Bud pattern and is now ready to be slipped over any transmitter s handle. This is one of Trayman s Patent Pending two part lock down system.

This is the Two Part Bungee-Bud Lock Down System. The First part is our rectangular Velcro Block. This piece of Billet Aluminum has been hogged out to remove any extra weight and is bolted to the Lower Cross Bar with two Stainless Steel Bolts that are secured with Red Lock-Tite. Rip-N-Grip self-adhesive hook material is applied to the Block. The softer loop Rip-N-Grip material is placed on the underside of any transmitter, between the transmitter s legs. Slip the Bungee Cord over the trans-

These are the two Stainless Steel Bolts that secure the Velcro Block before it is covered. The Rip-N-Grip hook material has been pre-applied. Just peal off the matching self-sticking loop material and after removing the white protective backing, apply it to the center of the underside of your transmitter. Be sure to leave an equal space between each of the two feet. Press the Rip-N- Grip into place firmly checking that the battery door is clear. If there is a serial number copy it down and tape it to the inside of the battery cover with your name.

Having pressed the Hook-N-Grip into position the transmitter can now be quickly mounted on the trays by simply lining up the two parts of the material

Interlock the Rip-N-Grip Pads, Slip the Bungee-Bud Cord over the handle only, line up the edge of the Tray with the handle and the transmitter is locked down.

The 2005 Ultra Lite fite all transmitters and more..

This is the Bungee-Bud and Rip-N-Grip Kit that come with each tray. There is an extra Bungee Cord, a pair of Spare Nylon Washers, and more self adhesive Rip-N-Grip material.

The Tilt Wrist Rest has been made to fit into any of the slots or threaded openings in the Trayman Tray Table. The long 10/32 threaded bolt will slide along the slots to be adjusted exactly where it will best fit the edge of your hand.

The Belt Buckle provide a pivot point and general pad for the Tray Tables to rest upon at the users waist. The Stainless Steel bolts are set into place with Red Lock-Tite so they will not come loose with use. The actual use of a belt is not required, for the general use, of our Ultra Lite 2005 Blue Trayman.

Disclaimer: Please note that none of the products shown as examples of applications for the use of our 2005 Ultra Lite Blue Trayman should suggest that the brands we have shown endorse our Tray. We are not affiliated with any other manufacturer of Transmitters, Video or Computer equipment. Our product fits many other applications in Film, Sports, Theater, Inventory, Intake clipboards, Artwork, Medical Services, and as a general personal reading or writing platform. There are new applications found for our unit every day. As you discover your own please let us know about them. Your comments are always welcome. Caution: All of the fittings and hardware are of stainless steel or hardened steel and all of the end points have been treated with Red Lock-Tite. No bolt has been made to be removed except those that are made to be adjusted. Caution: Do not overload your Trayman System. Be sure that all of the Quick Grip Knobs have been hand tightened especially the Table Tilt Swivel. The Wave Grip Teeth can only hold if they are properly engaged. Remember: Common sense and an eye towards safety are your best protection. Liability: Rc Trayman USA LLC assumes no liability for the use of this system or any damages that occur from it s being used in any application whatsoever.