a Nexans company Catalogue 2009
EUROMOLD COMPANY PRESENTATION EUROMOLD Euromold is the leading European specialised designer, manufacturer and distributor of prefabricated cable accessories for medium voltage energy distribution. Euromold provides a complete range of accessories for underground cables: pre-moulded EPDM or silicone rubber connectors, terminations and joints for cables and epoxy s for transformers and switch gear, as well as a large range of cold-shrinkable terminations and joints from to 42 kv. Euromold is also the manufacturer of electrical components for the high voltage accessories of the Nexans group. ISO 9001 Certificate Since 1992, Euromold s commitment to quality is demonstrated by its ISO 9001 certification. International All our products meet the International like CENELEC HD 629.1, CENELEC EN 50180, IEC 137, IEEE 386 & 404 or country specifications. Official certificates, CESI, KEMA, ATEX prove the conformity of our products. Long duration tests of existing or new products are continuously performed in our test fields. Laboratory accreditation Since June 2000, Euromold s independent ELAB laboratory obtained the BELTEST accreditation no.192-t-iso 17025 conform with the European for laboratories ISO 17025 for electrical testing of medium voltage cable accessories according to the International IEC 61442 and HD 629. While every care is taken to ensure that the information contained in this publication is correct, no legal responsibility can be accepted for any inaccuracy. Nexans Network Solutions n.v. - Div. Euromold reserves the right to alter or modify the characteristics of its products described in this catalogue as and technology evolve. 1
EQUIPMENT BUSHINGS Table of contents 180AR-1 - interface A 180AR-2 - interface A 180AR-3 - interface A 180A-P-O - interface A in-air 250SFR-P - interface A 400T1 - interface B 400AR-1 - interface B 400AR-2 - interface B 400SFR-P - interface B 400AR-3 - interface C 400AR-4 - interface C 400AR-5 - interface C 400AR-6 - interface C 400A-B - interface C in-air 400SFR-B - interface C 2
Interface A Dimensions according to European CENELEC EN 50180 and 50181 (in mm). Dia. 44.5 ±0.2 Dia. 32.5 ±0.2 Dia. 31 +0.1-0.3 Dia. for pin 7.9 +0.02-0.05 48 0-0.2 9 min. Dia. 48.5 ±0.2 Interface B Dimensions according to European CENELEC EN 50180 and 50181 (in mm). Dia. 56 ±0.2 Dia. 46 ±0.2 Dia. for pin 14 0-0.04 40 min. 90 ±0.2 11 min. Dia. 70 ±0.2 Interface C Dimensions according to European CENELEC EN 50180 and 50181 (in mm). Dia. 56 ±0.2 Dia. 46 ±0.2 Dia. 22 min. M16 x 2-6H 0 1.5-0.5 29 min. 90 ±0.2 11 min. Dia. 70 ±0.2 3
180AR-1 /180AR-2 /180AR-3 INTERFACE A EQUIPMENT BUSHINGS Application For use in insulated with oil fluid, typically for transformers, switch gear, capacitors... Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. Specifications and The plug-in type s 180AR- meet the requirements of CENELEC EN 50180 and IEC 137. Up to kv - 250 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv Design The s are moulded epoxy insulated parts in accordance with CENELEC EN 50180. The 180AR-2 has a length B outside this standard. The standard s, (K)180AR-1 /-2 /-3, are equipped with 6 tabs for the bail restraint. The (K)180AR-1-G and (K)180AR-3-G are equipped with 4 tabs and 2 threaded inserts M6 (-G version). Type 180AR-1-G /-3-G Type 180AR-1 /-2 /-3 M6 11 28 8 A B To order the, specify the type. The s are supplied with an earth jumper (/J) or an earth plate (/GS). This earth must be specified when ordering. E.g. K180AR-1/J. Minimum oil level: - kv: 40 mm - kv: 50 mm Dia. 16 Dia. 75 Dia. 110 M10 19 Equipment type Voltage Ur (kv) Current Ir (A) A Dimensions (mm) B 180AR-1 K180AR-1 180AR-2 K180AR-2 180AR-3 K180AR-3 250 250 250 250 250 250 222 222 284 284 171 171 106 106 168 168 55 55 4
180AR-1/GS 180AR-1-G/GS 180AR-2/GS 180AR-3/GS and 180AR-3-G/GS Bushings To order the clamping kit, according to NFC 52-053, simply specify KBCNF1-200. Contents: - 3 x claw clamp NF - 1 x sealing gasket. FIXINGS FOR EQUIPMENT BUSHINGS 180AR-1/J 180AR-1-G/J 180AR-2/J 180AR-3/J and 180AR-3-G/J Bushings To order the clamping kit, according to DIN 42 538, simply specify: KBCD-200. Contents: - 1 x fixing flange A - 4 x stud clamp E - 1 x sealing gasket. interface fixing studs NF C 52-053 clamp E DIN 42 538 stud clamp sealing gasket tabs for bail restraint A DIN 42 538 fixing flange earth plate earth jumper Fixing dimensions NF C 52-053 French. Fixing dimensions DIN 42 538 German. M8 or M10 M10 27 52 25 55 3 fixing studs Dia. 78 Dia. 6 4 fixing studs Dia. 78 Dia. 3 5
Application For use in insulated with air, typically for dry type transformers, motors, switch gear, capacitors... Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. 180A-P-O INTERFACE A IN-AIR BUSHING Up to kv - 250 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv Specifications and The plug-in type s 180A-P-O are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50181 and IEC 137. Dia. 70 59 20 A Dia. 110 To order the, specify the type. The s are supplied with an earth jumper. To include the ring clamp, add: /B, if per British /D, if per German /F, if per French. E.g. 180A-P-O/F. 250 351 Dia. 16 20 B Dia. 80 M10 Equipment type Voltage Ur (kv) Current Ir (A) Creepage distance A-B (mm) 180A-P-O 180A-P-O 250 250 6 6 6
180A-P-O In-air interface fixing studs and nuts M10 earth jumper FIXINGS FOR EQUIPMENT BUSHINGS gasket fixing flange BCA-B or BCA-D fixing flange BCA-F F tabs for bail restraint Dia. 94.5 Dia. 111 4 Dia. 10 Dia. 10 4 Dia. 94.5 Dia. 111 0 F 6 BS 2562 stand.: 0 DIN 42 538 stand.: 3 Dia. 150 Type BCA-B : BS 2562 British Type BCA-D : DIN 42 538 German Fixing dimensions DIN 42 538 German. M10 25 55 0 Dia. 150 Type BCA-F : NFC 52-053 French M8 or M10 27 52 Fixing dimensions NF C 52-053 French. 4 fixing studs 3 fixing studs Dia. 82 Dia. 3 Dia. 82 Dia. 6 7
Application For use in insulated with SF 6 gas. Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. 250SFR-P INTERFACE A EQUIPMENT BUSHING Up to kv - 250 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv Design The is a moulded epoxy insulated part with a connector interface in accordance with CENELEC EN 50180. The 250SFR-P has a shank outside this standard, adapted to use in SF 6 gas. Specifications and The plug-in type s 250SFR-P meet the requirements of CENELEC EN 50180 and IEC 137. Dia. 70 Dia. 48.5 31 174 95 To order the, simply specify the type. M10 Dia. 20 Dia. 70 Dia. 109 Equipment type Voltage Ur (kv) Current Ir (A) 250SFR-P K250SFR-P 250 250 8
FIXINGS FOR EQUIPMENT BUSHINGS 250SFR-P Bushing for gas insulated switch gear UNMOUNTED 60 60 60 M4 83 M6 Dia. 91.5 Dia. 103.1 MOUNTED interface 6 fixing screws M6 sealing O-ring gasket earth M4 9
400T1 /400AR-1 /400AR-2 INTERFACE B EQUIPMENT BUSHINGS Application For use in insulated with oil fluid, typically for transformers, switch gear, capacitors... Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. Up to kv - 400 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv 18/ () kv Specifications and The plug-in type s are moulded epoxy insulated parts and meet the requirements of IEC 137. The (K)(M)400T1 also meets CENELEC EN 50180. C 10 133 To order the, specify the type. The s are supplied with an earth jumper (/J) or an earth plate (/GS). This earth must be specified when ordering. E.g. K400AR-1/J. Minimum oil level: - kv: 40 mm - kv: 50 mm - kv: 70 mm Dia. H B A E Dia. 70 Dia. F Dia. G D In mm Equipment type Voltage Ur (kv) Current Ir (A) Dimensions (mm) A B C D E Dia. F Dia. G Dia. H 400T1 K400T1 M400T1 400AR-1 K400AR-1 M400AR-1 400AR-2 K400AR-2 M400AR-2 400 400 400 400 400 400 400 400 400 310 310 310 380 380 380 329 329 329 144 144 144 213 213 213 138 138 138 M M M M M M M16 M16 M16 22 22 22 22 22 22 40 40 40 88 88 88 74 74 74 100 100 100 8 8 8 8 8 8 150 150 150 16 16 16 16 16 16 10
400AR-2/GS Bushing To order the clamping kit, according to NFC 52-053, simply specify KBCNF-400 (for type 400AR-2). Contents: - 4 x claw clamp NF - 1 x sealing gasket. FIXINGS FOR EQUIPMENT BUSHINGS 400AR-1/J and 400T1/J Bushings To order the clamping kit, simply specify: KBCD-400B. Contents: - 1 x fixing flange B - 6 x stud clamp E - 1 x sealing gasket. interface fixing studs NF C 52-053 claw clamp fixing flange B DIN 42 538 E DIN 42 538 stud clamp sealing gasket tabs for the bail restraint earth jumper earth plate Fixing dimensions NF C 52-053 French. Fixing dimensions DIN 42 538 German. M10 or M M10 50 to 70 55 25 4 fixing studs Dia. 105 Dia. 171 6 fixing studs Dia. 90 Dia. 140 In mm 11
Application For use in insulated with SF 6 gas. Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. 400SFR-P INTERFACE B EQUIPMENT BUSHING Up to kv - 400 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv Design The is a moulded epoxy insulated part with a connector interface in accordance with CENELEC EN 50180. The 400SFR-P has a shank outside this standard, adapted for use in SF 6 gas. Dia. 70 218 Specifications and The plug-in type 400SFR-P meets the requirements of CENELEC EN 50180 and IEC 137. 33 To order the, simply specify the type. 95 Dia. 25 Dia. 70 Dia. 109 M Equipment type Voltage Ur (kv) Current Ir (A) 400SFR-P K400SFR-P 400 400
FIXINGS FOR EQUIPMENT BUSHINGS 400SFR-P Bushing for gas insulated switch gear UNMOUNTED 60 60 60 M4 83 M6 Dia. 91.5 Dia. 103.1 MOUNTED interface 6 fixing screws M6 sealing O-ring gasket earth M4 13
Application For use in insulated with oil fluid, typically for transformers, switch gear, capacitors... Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. 400AR-3 INTERFACE C EQUIPMENT BUSHING Up to kv - 6 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv 18/ () kv Specifications and The bolted type s 400AR-3 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 137. 133 To order the, specify the type. The s can be supplied with an earth jumper (/J). E.g. M400AR-3/J. For use in potentially explosive atmospheres (for kv max), order: 400AR-3/ATEX. Minimum oil level: - kv: 40 mm - kv: 50 mm - kv: 70 mm Dia. 25 10 144 3 40 M16 Dia. 70 Dia. 88 Dia. 8 Equipment type Voltage Ur (kv) Current Ir (A) 400AR-3 K400AR-3 M400AR-3 6 6 6 14
400AR-3/J Bushing FIXINGS FOR EQUIPMENT BUSHINGS To order the clamping kit, according to DIN 42 538, simply specify KBCD-400B. Contents: - 1 x fixing flange B - 6 x stud clamp E - 1 x sealing gasket. Fixing dimensions DIN 42 538 German. M10 25 55 interface fixing studs B DIN 42 538 fixing flange E DIN 42 538 stud clamp 6 fixing studs Dia. 90 Dia. 140 sealing gasket earth jumper 15
Application For use in insulated with oil fluid, typically for transformers, switch gear, capacitors... Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. 400AR-4 INTERFACE C EQUIPMENT BUSHING Up to kv - 50 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv 18/ () kv Specifications and The bolted type s 400AR-4 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 137. 139 To order the, specify the type. The s can be supplied with an earth jumper (/J) or an earth plate (/GS). This earth must be specified when ordering. E.g. M400AR-4/GS. Minimum oil level: - kv: 40 mm - kv: 50 mm - kv: 70 mm Dia. 32 10 138 329 40 M16 Dia. 70 Dia. 100 Dia. 150 Equipment type Voltage Ur (kv) Current Ir (A) 400AR-4 K400AR-4 M400AR-4 50 50 50 16
400AR-4/GS Bushing FIXINGS FOR EQUIPMENT BUSHINGS To order the clamping kit, according to NFC 52-053, simply specify KBCNF-400. Contents: - 4 x claw clamp NF - 1 x sealing gasket. Fixing dimensions NF C 52-053 French. M10 or M 50 to 70 interface fixing studs 4 fixing studs Dia. 105 Dia. 171 NF C 52-053 claw clamp sealing gasket earth plate 17
Application For use in insulated with oil fluid, typically for transformers, switch gear, capacitors... Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. 400AR-5 INTERFACE C EQUIPMENT BUSHING Up to kv - 50 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv 18/ () kv Specifications and The bolted type s 400AR-5 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 137. 139 To order the, specify the type. The s can be supplied with an earth jumper (/J) or an earth plate (/GS). This earth must be specified when ordering. E.g. M400AR-5/GS. Minimum oil level: - kv: 40 mm - kv: 50 mm - kv: 70 mm Dia. 32 72 32 5 M16 Dia. 76 Dia. 150 Equipment type Voltage Ur (kv) Current Ir (A) 400AR-5 K400AR-5 M400AR-5 50 50 50 18
400AR-5/GS Bushing FIXINGS FOR EQUIPMENT BUSHINGS To order the clamping kit, according to NFC 52-053, simply specify KBCNF-400. Contents: - 4 x claw clamp NF - 1 x sealing gasket. Fixing dimensions NF C 52-053 French. M10 or M interface 50 to 70 fixing studs 4 fixing studs Dia. 81 Dia. 171 NF C 52-053 claw clamp sealing gasket earth plate 19
Application For use in insulated with oil fluid, typically for transformers, switch gear, capacitors... Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. 400AR-6 INTERFACE C EQUIPMENT BUSHING Up to kv - 6 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv 18/ () kv Specifications and The bolted type s 400AR-6 are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 137. To order the, specify the type. The s can be supplied with an earth jumper (/J). This earth must be specified when ordering. E.g. M400AR-6/J. 132 10 398 213 Minimum oil level: - kv: 40 mm - kv: 50 mm - kv: 70 mm Dia. 25 40 Dia. 70 Dia. 88 Dia. 8 M16 Equipment type Voltage Ur (kv) Current Ir (A) 400AR-6 K400AR-6 M400AR-6 6 6 6 20
400AR-6/J Bushing FIXINGS FOR EQUIPMENT BUSHINGS To order the clamping kit, according to DIN 42 538, simply specify KBCD-400B. Contents: - 1 x fixing flange B - 6 x stud clamp E - 1 x sealing gasket. Fixing dimensions DIN 42 538 German. interface fixing studs M10 25 55 fixing flange B DIN 42 538 E DIN 42 538 stud clamp 6 fixing studs Dia. 80 Dia. 140 sealing gasket earth jumper 21
Application For use in insulated with air, typically for dry type transformers, motors, switch gear, capacitors... Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. 400A-B INTERFACE C IN-AIR BUSHING Up to kv - 6 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv Specifications and The bolted type s 400A-B are moulded epoxy insulated parts and meet the requirements of CENELEC EN 50180 and IEC 137. 20 To order the, specify the type. The s are supplied with an earth jumper. To include the ring clamp, add: /B, if per British /D, if per German /F, if per French. E.g. 400A-B/D. For use in potentially explosive atmospheres (for kv max), order: -/ATEX. A Dia. 80 Dia. 110 Dia. 25 250 434 40 B Dia. 80 M16 Equipment type Voltage Ur (kv) Current Ir (A) Creepage distance A-B (mm) 400A-B 400A-B 6 6 500 500 22
400A-B In-air FIXINGS FOR EQUIPMENT BUSHINGS interface fixing studs and nuts M10 earth jumper gasket fixing flange BCA-B or BCA-D fixing flange BCA-F F Dia. 94.5 Dia. 111 4 Dia. 10 Dia. 10 Dia. 94.5 4 Dia. 111 0 F 6 BS 2562 stand.: 0 DIN 42 538 stand.: 3 Dia. 150 Type BCA-B : BS 2562 British Type BCA-D : DIN 42 538 German Fixing dimensions DIN 42 538 German. 0 Dia. 150 Type BCA-F : NFC 52-053 French Fixing dimensions NF C 52-053 French. M10 M8 or M10 55 25 52 27 4 fixing studs 3 fixing studs Dia. 82 Dia. 3 Dia. 82 Dia. 6 In mm 23
Application For use in insulated with SF 6 gas. Technical characteristics Each is tested for AC withstand and partial discharge prior to leaving the factory. 400SFR-B INTERFACE C EQUIPMENT BUSHING Up to kv 6 A & 50 A 6/10 () kv 6.35/11 () kv 8.7/15 (17.5) kv /20 () kv.7/22 () kv Design The is a moulded epoxy insulated part with a connector interface in accordance with CENELEC EN 50180. The 400SFR-B has a shank outside this standard, adapted to use in SF 6 gas. Dia. 70 219.5 Specifications and The bolted type 400SFR-B meets the requirements of CENELEC EN 50180 and IEC 137. 33 95 To order the, simply specify the type. M Dia. D Dia. 70 Dia. 109 Equipment type Voltage Ur (kv) Current Ir (A) Dia. D (mm) 400SFR-B K400SFR-B M400SFR-B 400SFR-B 50 A K400SFR-B 50 A M400SFR-B 50 A 6 6 6 50 50 50 25 25 25 32 32 32
FIXINGS FOR EQUIPMENT BUSHINGS 400SFR-B Bushing for gas insulated switch gear UNMOUNTED 60 60 60 M4 83 M6 Dia. 91.5 Dia. 103.1 MOUNTED interface 6 fixing screws M6 sealing O-ring gasket earth M4 25
Additional catalogue information on power cable accessories is available by contacting us at the address below: Distributed by: Nexans Network Solutions N.V. - Div. Euromold Zuid III, Industrielaan, B-9320 Erembodegem Tel.: +32 (0)53 85 02 11 Fax: +32 (0)53 83 10 13 www.nexans.com info.euromold@nexans.com Catalogue also available on CD-ROM