ION-MILL-GTP1 GTP-1 MOBILE GUARD TOWER The Phalanx GTP-1 Guard Tower can be set in place and made ready for use in under 5 minutes. The Guard Tower s ability to be rapidly deployed make it ideal for Military Checkpoints, Dock Security, Border Patrol Operations, etc. The ballistic panels surrounding the Guard Tower are NIJ4 rated and provide 360º protection from 7.62mm ammunition. The internal ladder keeps occupants concealed while entering and exiting the tower. Each unit comes with a lightning rod kit, fold out rain/shade visors, folding weapon support shelves which are attached to the ballistic walls and a radio storage shelf in the Tower. ships completely assembled and ready for deployment The GTP-1 is delivered fully assembled. GTP-1 comes equipped with a battery operated pump for raising and lowering the unit. The 12V battery operated pump makes setup as easy as pressing a button. Systems is charged by the solar panel built onto the GTP-1 s visor. The internal ladder is designed to automatically extend when the Guard Tower is in the up position. BENNIFITS Fast and Simple Setup Facilitates Rapid Repositioning of Assets 360º Protection (NIJ4 Ballistic panels) Easily transportable Battery-Operated Hydraulic Lift Self contained Self contained solar power supply powers Quick Press button which activates the GTP-1 Guard Tower to raise into a deployed position.
ION-MILL-GTP1 GTP-1 MOBILE GUARD TOWER The GTP-1 unit base conforms to standard shipping container specifications. It is air transportable via air on a standard 463L pallet. The GTP-1 Guard Tower can be transported easily by pickup, HUMVEE and most military vehicles, and slung under helicopter. The optional GTP-TR65L trailer makes it possible to position, tow or recover the Tower without the use of any heavy equipment. The GTP-1 can be loaded onto the GTP-TR65L trailer as shown to the left. It allows you to keep your GTP-1 portable for emediate relocation. GTP-1 is shippable inside a container. When the GTP-1 is kept on the GTP-TR65L Trailer a step is included for accessing the GTP-1 Tower. There are 4 leveling legs (1 on each corner) that are lowered to stabilize and level the GTP-1. Also, your Guards eyes will be up to almost 20 ft (6 meters) above the ground.. The GTP-1 Guard Tower can be trans-ported easily by pickup, HUMVEE and most military vehicles, and slung under helicopter. The optional GTP-TR65L trailer makes it possible to position, tow or recover the Tower without the use of any heavy equip-ment.
ION-MILL-GTP1 GTP-1 MOBILE GUARD TOWER Optional Wind/Rain Shield protection is also available that is attached with Velcro. The photo to the left shows the Shield attached with the clear side to the top. It can be reversed to put the solid side to the top, which will block your view from that side. GTP-1 Tower is equiped with folding weapon support shelves which are attached to the ballistic walls including a radio storage shelf. GTP-1 Tower is compact and versitile designed for survielence in remote locations. Build complete camp protection with Phalanx 8ft HT Series barricades Part No. Description Weight Shipping Size GTP-1 GTP-1 Guard Tower 6200 lbs. 2812 Kgs 8 (long) x 6.5 (wide) x 8 (tall) GTP-1-WRVS Wind/Rain/Visibility Shield 50 lbs. 22 kgs 12 (diameter) x 32 (long) GTP-TR65L GTP-1 Trailer 2000 lbs 907 Kgs 14 (long) x 88 (wide) x 3 (tall)
ION-MILL-GTP2 GTP-2 MOBILE GUARD TOWER The GTP-2 Guard Tower is manufactured with four separate wall units that allow for quick and easy assembly on top of the standard Conex Box. Once placed on the Conex Box the Guard Tower will be approximately 12 feet in the air, giving the guards a greater view of the perimeter or area of threat. Once in position, the walls are filled from the top using sand as ballast. The sand filled walls provide the guards inside with 360 degrees of protection from 9mm, 5.56, and 7.62 threats. 12 dumps are provided for easy removal of the ballast allowing the Guard Tower to be repositioned as needed. The overhead cover is 3/4 plywood on which lights, sensors, and antenna can be installed if desired. Access to the cover can be reached through a hatch type door that is pre-installed for convenience. The GTP-2 Guard Tower eliminates the time and the mess associated with using sandbags. This product is a recoverable asset that can be broken down and deployed inside the Conex Box
ION-MILL-GTP2 GTP-2 MOBILE GUARD TOWER The GTP-2 Guard Tower and all parts and tools needed for assembly are included in the kit bag. Stakes are also provided for the Concertina Wire installation. The standard colors for the Portable Guard Tower are Olive Drab or Desert Tan; however, all colors are available upon request. There is also an optional wind/rain/visibility Shield available in Olive Drab and Desert Tan. Wind screen attaches with Velcro. The Portable Guard Tower can be ordered in various configurations as listed below Easy removal of the ballast allows the Guard Tower to be repositioned as needed. OPTION 1 streight Ladder only OPTION 1 steight Ladder/ Walkthru OPTION 1 bolt on Stairs/ Walkthru
ION-MILL-GTP2 GTP-2 MOBILE GUARD TOWER GTP-2 is avaiable in 3 different options for accessing the Guard Tower: Ladder only Ladder attached on non-threat side of Guard Tower. When accessing the Guard Tower, you will climb to the top of the ladder and crawl over the top. (Shown in photo below) Ladder with Walk Through Ladder attached on non-threat side of Guard Tower on one side of Walk Through opening in wall. When accessing the Guard Tower, you will climb most of the way up the ladder and step into the Guard Tower through the opening in the one side wall. Note, the Walk Through is typically in the long wall (LEFT IM- AGE), but can be ordered in short wall (RIGHT IM- AGE) if required. Angled Stairs with Walk Through Stairs are attached on non-threat side of Guard Tower to the Walk Though opening in the wall. When accessing the Guard Tower, you will walk up the stairs and step into the Guard Tower through the opening in the one side wall. Note, the Walk Through is typically in the long wall, but can be ordered in short wall if required.
ION-MILL-GTP2 The Portable Guard Tower can be ordered in various configurations GTP-2 MOBILE GUARD TOWER as listed below: Guard Tower only Can be placed on the ground or on top of a TriCon Container that you supply. Will be shipped on skid. Guard Tower with TriCon Container Guard Tower will be shipped inside TriCon Container with all tools for installation. Complete Guard Tower with TriCon Container Guard Tower will be shipped inside TriCon Container with all tools for installation, razor wire and wire installation kit. The Wire Installation Kit includes a Fence Driver, 25 5-foot stakes, and 25 7-foot stakes. Part No. Item Color Size Weight GTP-2-OD-GT Guard Tower Olive Drab W 4 x H 8 x L 8 1800 lbs. GTP-2-DT-GT Guard Tower Desert Tan W 4 x H 8 x L 8 1800 lbs. GTP-2-OD-GTCB Guard Tower w/tricon Container Olive Drab W 8 x H 8 x L 6 5.5 4400 lbs. GTP-2-DT-GTCB Guard Tower w/tricon Container Desert Tan W 8 x H 8 x L 6 5.5 4400 lbs. GTP-2-OD Complete Guard Tower Unit Olive Drab W 8 x H 8 x L 6 5.5 5000 lbs. GTP-2-DT Complete Guard Tower Unit Desert Tan W 8 x H 8 x L 6 5.5 5000lbs OPTIONS Part No. Item Color GTP-2-OD-WRVS Wind/rain/visibility Shield Olive Drab GTP-2-DT-WRVS Wind/rain/visibility Shield Desert Tan GTP-2-L Ladder GTP-2-LWT Walkthrough with Ladder GTP-2-SWT Walkthrough with Stairs GTP-2-WRK Wood Replacement Kit GTP-2-CWK Concertina Wire Kit
ION-MILL-GTP3 GTP-3 MOBILE COMMAND GUARD TOWER The GTP-3 Command Guard Tower includes one Guard Tower & two Conex Boxes. The Guard Tower itself is manufactured with six separate wall units that allow for quick and easy assembly on top of the standard Conex Boxes. Once placed on the Conex Boxes, the Guard Tower will be approximately 13 feet (4 meters) in the air, giving the guards a greater view of the perimeter or area of threat. Once in position, the walls are filled from the top using sand as ballast. The sand filled walls provide the guards inside with 360 degrees of protection from 9mm, 5.56 and 7.62 threats. 12 dumps are provided for easy removal of the ballast allowing the Guard Tower to be repositioned as needed. The overhead cover is 3/4 plywood on which lights, sensors, and antennae can be installed if desired. Access to the cover can be reached through a hatch type door that is pre-installed for convenience. The CBP Command Guard Tower eliminates the time and the mess associated with using sandbags. This product is a recoverable asset that can be broken down and deployed inside the Conex Boxes
ION-MILL-GTP3 GTP-3 MOBILE COMMAND GUARD TOWER GTP-3 is avaiable in 3 different options for accessing the Guard Tow- Ladder only Ladder attached on non-threat side of Guard Tower. When accessing the Guard Tower, you will climb to the top of the ladder and crawl over the top. (Shown in photo below) Ladder with Walk Through Ladder attached on non-threat side of Guard Tower on one side of Walk Through opening in wall. When accessing the Guard Tower, you will climb most of the way up the ladder and step into the Guard Tower through the opening in the one side wall. Note, the Walk Through is typically in the long wall but can be ordered in short wall (RIGHT IMAGE) if required. Angled Stairs with Walk Through Stairs are attached on non-threat side of Guard Tower to the Walk Though opening in the wall. When accessing the Guard Tower, you will walk up the stairs and step into the Guard Tower through the opening in the one side wall. Note, the Walk Through is typically in the long wall, but can be ordered in short wall if required.
ION-MILL-GTP3 GTP-3 MOBILE COMMAND GUARD TOWER Part No. Item Color Size Weight GTP-3-OD Command Guard Tower Only Olive Drab W 8 x H 8 x L 13 1800 lbs. GTP-3-DT Command Guard Tower Only Desert Tan W 8 x H 8 x L 13 1800 lbs. GTP-3-OD-2TC Guard Tower w/2 TriCon Container Olive Drab W 8 x H 8 x L 13 7000 lbs. GTP-2-DT-2TC Guard Tower w/tricon Container Desert Tan W 8 x H 8 x L 13 7000 lbs. GTP-2-OD Complete Guard Tower Unit Olive Drab W 8 x H 8 x L 13 7500 lbs. GTP-2-DT Complete Guard Tower Unit Desert Tan W 8 x H 8 x L 13 7500lbs OPTIONS Part No. Item Color GTP-3-OD-WRVS Wind/rain/visibility Shield Olive Drab GTP-3-DT-WRVS Wind/rain/visibility Shield Desert Tan GTP-2-WRK Wood Replacement Kit