Installer and user s manual VARANDA AWNING 2 persons Necessary tools INFORMATION PRE-INSTALLATION Important! efore the installation, check the leveling of the place where you will apply the awning. Dimensions should be parallels and levelled. In case the balcony is not level it's necessary an chock application to allow correctly the installation of the awning fixing plates. N 13 N 17 N N 5 porch 1 Inside package Ce c Variable number Eb Rt Sp Po2 Po1 Eq
2 Fixing plates preparation A assembly top Sp bottom 20cm max 100cm max 100cm max assembly Eq N Make the same assembly to the other profile. 3 Awning and frontal profile preparation. c A Disassemble Assembly C Slide the frontal profile on the fabric. D Assembly again Po1
Fixation plates application. alcony without tubes supports A Ø6x1mm C 30cm mini D E F G Attention, is necessary to respect the position described above represented for a awning set assembly. Adapt the awning fixation to the balcony type. alcony with support tubes. A C D E 30cm min Ø6x1mm F Adapt the awning fixation to the balcony type. support tubes attention, is necessary to respect the position described above represented for a awning set assembly.
5 Others supports alcony without supporting tubes. Simple guide Double guide alcony with support tubes. Simple guide Double guide
6 Installation of safe A C
6 Placing the maneuver rope. A assembly disassemble 50cm Attention, for correct operation of the awning, pay close attention to the following statements. Operation to be carried out on the 2 reinforcements. face D front profile 50cm Eb cover C Face D Front profile winding direction P1 to C All respecting the winding direction, perform 3 courses of wire around the roller tube and pulley set. Pass the thread underneath the pulley P1 sliding it by the guide and finding the bottom cover in C.! Attention from to C ensure that the rope does not wind on her own, it can cause a break after much use. to D from Then slide the rope by the profile, pass the rope through the pulley and make it slide again by the profile until the load bar. Attention: the placement of the cover will be made at the time of string stretched. - Ac from to D Cover C Eb OK NO Preassembly 2 parts. 1 Po1 pulley must be placed in the middle of the front profile. Rt Po2 to 3 from C 2 Po1 from 2 to 3 from 3 to 5 Po2 Po1 to for closure from Ac 5
7 Fabric stretch Pull the end of the rope by hand and lock on release AC. The stretch should identify two sides to check that the pulley Po1 is well positioned in the center of the front profile. Ensure that the rope is guided on all the pulleys of the system. Open the awning down. Open the fabric 50cm, to perform another string tension. Make an opening maneuver and closing. The awning becomes tense. 8 Regulation of the limit switches The travel stops are pre-adjusted in factory. To adjust: - Unscrew the limit screw + or - to make the desired setting. Rotating + to get more closing or opening turning - to get less closing or opening. -Make a test. N N osure Awning open 30cm Opening 7 Finishing After adjustments are made, put the safe cover again (paragraph 6) and the front cover profile (paragraph 3). Assembly end
Information to the consumer Awning maintenance advice An awning is subject to some adverse situations: moisture, salt spray, balance, wind... we recommend that: - Check the tightening of the screws and the limit after installation and regularly at the beginning and end of each season. -Never close a wet awning. Dry it if possible. -ean the fabric and the frame at the beginning and end of each season. Caution: never use detergents. Problems The awning balcony disintegrated from the structure. The front profile does not work normally. The fabric is not stretched. The awning does not open or close. Electric awning maneuvers do not work. Electric awning maneuvers do not work. Causes The Mounting brackets are not adapted to the composition of the structure. A Rope broke free of a pulley. The Tension of one rope is superior to another (double Po1 offset) Incorrect voltage on the base. Fabric not stretched. (Natural effect) Rope break. Electrical maneuver faulty The engine is placed in thermal protection after 2 descents and a 1 rise successives. Connection problem. Solutions Check proper placement of the supports (according to the manual's instructions). In case of fixing with a chemical seal, report to the manufacturer. Check the entire circuit of the rope to find a possible shift of the rope. (Paragraph 6) Check if the voltage is identical in the 2 sides (sheave Po1 centered) (Paragraph 6) Tighten the rope (Paragraph 7) Do the full circuit of the rope again. paragraph 6 Test the electrical part to find the problem. Wait the end of protection (20 minutes) Check the motor connection Check engine operation by connecting directly to the power input. (black or brown blue blue) Not install the awning in case of: Wind Rain Snow Nothing suspended
Exploded view 7 6 8 5 9 10 3 11 2 12 1 13 1 15 16 17 18 SV35 SV302 SV15A SV0 = 9mm SV1 = 13mm SV2 = 20mm Number Reference Designation 1 JSV03A Aluminum parts 2 FUM2 Engine bracket 3 TM0 Tubular motor CV03/CV02 Safe cover 5 PO16P Pulley winding tube 6 TO78 Roller tube Ø78mm 7 CV01 Safe profile 8 EO678P ushing Ø78mm 9 CU1A Roller tube support 10 SV06A Safe guide 11 PU807 Sliding profile 12 SV05 Front cover profile 13 E0802 Guide cover 1 PU370 Front profile s cover 15 TR19 The fabric tension spring 16 PO20 Pulley to spring TR19 17 PU3703 Front Profile 18 PO2102 Tension pulley N.R* AC02 Fixing the rope to the terminal profile N.R* C03 Rope *no represented part