MODEL : MB86 Murphy Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly. NOTE : RETIN OR UTURE USE TWO PEOPLE REOMMENDED OR SSEMBLY ITEM DESRIPTION QTY. ITEM DESRIPTION QTY. * 1/" SQURE P 16 UPPER END PNEL G* 1" X 1/" RETNGULR P H* 7/8" ROUND P 8 I* 1" ROUND P B LOWER END PNEL J* BUNK ONNETOR K* 1/"-0 X 1" SREW L* 1/"-0 X 1 1/" SREW DEK M* OM TPE N* HEX KEY 1 *HRDWRE KIT 9W1670 D GURD RIL EN! WRNING: - This package contains small parts. Keep away from children during assembly. - dult assembly required. - Phillips head screw driver required. - Instructions are generic. igures may vary. - Screws left after assembly should be kept out of reach of children. E LDDER 1 OR SEPRTE TWIN BEDS, SSEMBLY BEGINS ON PGE. OR BUNK BEDS, SSEMBLY BEGINS ON PGE 3. PGE 1 O 5 Welton US 07-03-1 00 Dividend Drive Suite 00 oppell, TX 75019 Phone 1-800-759-1559 ax 69-3-6501 www.weltonus.com
MODEL : MB86 Murphy SEPRTE TWIN BEDS TTH SQURE PS() TO EH END PNEL(,B). SLIDE THE TBS ON DEK() INTO THE SLOTS ON LOWER END PNEL(B) ND THEN PRESS DOWN. REPET WITH UPPER END PNEL(). REPET WITH THE OTHER BED. B PGE O 5 Welton US 00 Dividend Drive Suite 00 oppell, TX 75019 Phone 1-800-759-1559 ax 69-3-6501 www.weltonus.com
BUNK BEDS STEP 1: INSERT RETNGULR PS(G) ND ROUND PS(H) TO EH GURD RIL(D). MODEL : MB86 Murphy INSERT ROUND PS(I) TO LDDER(E). REMOVE THE PPER BKING ROM THE OM TPE(M) ND TTH IT TO THE INSIDE O THE LDDER HOOKS S SHOWN. H M H G E STEP TTH SQURE PS() TO THE BOTTOM O EH LOWER END PNEL(B). I TTH BUNK ONNETORS(J) TO THE TOP O EH LOWER END PNEL(B). SLIDE THE TBS ON DEK() INTO THE SLOTS O LOWER END PNEL(B) ND THEN PRESS DOWN. REPET WITH THE OTHER SIDE. J B PGE 3 O 5 Welton US 00 Dividend Drive Suite 00 oppell, TX 75019 Phone 1-800-759-1559 ax 69-3-6501 www.weltonus.com
STEP 3: TTH SQURE PS() TO THE TOP O EH UPPER END PNEL(). MODEL : MB86 Murphy SLIDE THE TBS ON DEK() INTO THE LOWER SLOTS O UPPER END PNEL() ND THEN PRESS DOWN. REPET WITH THE OTHER SIDE. TTH BOTH GURD RILS() TO THE SSEMBLY BY SLIDING THE TBS INTO THE TOP SLOTS O THE UPPER END PNELS() ND THEN PRESSING DOWN. IMPORTNT! SEURE EH GURD RIL WITH SREWS(K). DO NOT USE THIS BED WITHOUT THESE SREWS INSTLLED. D PGE O 5 Welton US 00 Dividend Drive Suite 00 oppell, TX 75019 Phone 1-800-759-1559 ax 69-3-6501 www.weltonus.com
MODEL : MB86 Murphy STEP LIT THE UPPER BUNK BOVE ND LOWER BUNK ND SET THE END PNELS INTO THE BUNK ONNETORS(J). J STEP 5 TTH LDDER(E) TO THE TOP BUNK WITH SREWS(L) USING HEX KEY(N). L L E PGE 5 O 5 Welton US 00 Dividend Drive Suite 00 oppell, TX 75019 Phone 1-800-759-1559 ax 69-3-6501 www.weltonus.com
! WRNING! SETY WRNING TO HELP PREVENT SERIOUS OR TL INJURIES ROM ENTRPMENT OR LLS Never allow a child under 6 years on upper bunk. Use only mattress which is 7 75 long and 37 ½ - 38 ½ wide on upper bunk (TWIN size). Ensure thickness of mattress and foundation combined does not exceed 6 and mattress surface is at least 5 below upper edge of guardrails. Use guardrails on both sides of upper bunk. Prohibit horseplay on or under bed(s). Prohibit more than one person on upper bunk. Use ladder for entering and leaving upper bunk. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall. STRNGULTION HZRD Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited to, hooks, belts, and jump ropes. ERTIIED This bunk bed conforms to all applicable consumer product safety Standards 16 R PRTS 113, 1500, +1513, ND STM -17 ERTIITE ERTIIED - THIS BUNK BED ONORMS TO LL PPLIBLE ONSUMER PRODUT SETY STNDRDS. 16 R PRTS 113, 1500, +1513 ND STM -17 ollow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning labels from bed. lways use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls. Use only mattress which is 7-75 long and 37 ½ - 38 ½ wide on upper bunk Ensure thickness of mattress and foundation combined does not exceed 6. Surface of mattress must be at least 5 (17mm) below the upper edge of guardrails. Do not allow children under 6 years of age to use the upper bunk. Prohibit more than one person on upper bunk. Periodically check and ensure that the guardrail, ladder and other components are in their proper position, free from damage and that all connectors are tight. Do not allow horse play on or under the bed and prohibit jumping on the bed. lways use the ladder for entering and leaving the upper bunk. Do not use substitute parts. ontact the manufacturer or dealer for replacement parts. Use of a night light may provide added safety precaution for a child using the upper bunk. lways use guardrails on both the long sides of the upper bunk. The use of water or sleep flotation mattresses is prohibited. STRNGULTION HZRD Never attach or hang items to any part of he bunk bed that are not designed for use with the bed; for example, but not limited to, hooks, belts and jump ropes. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall. Should there be any missing or defective parts, please call 1-800-759-1559. KEEP THESE INSTRUTIONS OR UTURE REERENE