Salisbury by Honeywell

Class 3 Conductor Covers 5 cover is ideal for covering long spans when weight is a consideration 26.4kV voltage rating 2 inside diameter May be connected with Salisbury 1.5 I.D. Class 3 or 4 flexible cover-up equipment Conductor covers connect easily with either plastic or rubber line hose 21172 5 Cover with Eye 21173 27kV, 5 Cover 21315 5 Cover wtih 4 Fiberglass Stick 21826 Lightweight 35kV, 6 Conductor Cover Straight Line Hose Orange Type II SALCOR line hose wth RIB-GRIP locking system Hoses remain flexible even in cold weather and are not damaged by ozone or ultraviolet rays Other sizes and classes are available Line Hose - Extended Lip SU System The Extended Lip SU System is the only complete flexible cover-up available for use on voltages through 34.5kV Extremely versatile, it may be installed by hand Manufactured from superior SALCOR Type II elastomer, it is resistant to the effects of ozone and ultraviolet deterioration It remains flexible even at sub-zero temperatures Salisbury s RIB GRIP construction securely interlocks with its corresponding covers and connectors Tapered lips facilitate easy starting on the conductors The contour cut ends accommodate the skirts of pin type insulators and permit the hose to cover the line snug to a saddle or clamp Available as Straight Line Hose or with a Connector End for easier connection of line hose and covers Part # Type Class I.D. x Length OR125-3 II 2 1.25 x 3 OR125-45 II 2 1.25 x 4.5 OR125-6 II 2 1.25 x 6 OR150-3 II 3 1.5 x 3 OR150-6 II 3 1.5 x 6 Part # Type Class I.D. x Length SU150-45C II 4 1.5 x 4.5 SU150-6C II 4 1.5 x 6 SU150-6C Stinger Cover Part # Description Protects against phase-to-phase and phase-to-ground wildlife contacts Track resistant May be installed without disconnecting the lead wire from the bushing Easy to cut to the necessary length Ozone and UV resistant SALCOR elastomer Silicon Bushing Cover Ozone and UV resistant silicone rubber Protects against wildlife contacts between energized equipment and ground by insulating exposed energized bushing parts Interlock with the top weathershed of the bushing and are securely fastened by inserting lock buttons Cover is 3.87 diameter x 3.37 tall 38-50SC 38-12SC 58-12SC 34-12SC 3/8 x 50 1 coil 3/8 x 12 4 pcs 5/8 x 12 coil 4 pcs 3/4 x 12 coil 4 pcs Part # Description 21116 Cover Only; 16kV 21116TC Cover with Tube Closure; 16kV 21644 Tube Closure 32

1370 & 1371: Crossarm Guards Available in two different styles: the 1370 pin type and the 1371 post type Used to prevent tie wires from contacting crossarms during hot line operations Two different tie downs provided: a neoprene and a polypropylene rope Both are secured in the slots provided in the eye fitting Post type model has an automatic gap closer which covers the insulator slot opening over the end of the arm Made from orange Type I ABS cold weather high impact plastic 736PH: Slide-On Crossarm Guard Applied by sliding the cover on to the arm from the end using the shotgun eye until the unit locks onto the insulator pins Cover overlaps on top and has notches to ease application and removal Made from orange Type I ABS cold weather high impact plastic Part # Description Dimensions ASTM Voltage Weight (lb.) Class 1370 Crossarm or Pin Type 4 5.7 Guard 9 x 9 x 25.5 1371 Crossarm or Post Fits Crossarm: 5 x 6 4 6 Type Guard 736PH Slide-On Crossarm Guard 7 4 4.5 Versa Guards & Link Guards Make use of air as well as the dielectric strength of plastic to provide total insulating value Both guards have a 7 diameter and a hook shaped inner lip to keep the guard in place Versa Guards: voltage rating of 36.6kV are designed so that two guards can be coupled together to cover most 13kV single and double arm, pin and post constructions Link Guards: voltage rating of 72.5kV, have inner and outer shells that run full length to include male and female couple ends Two guards connected provide four overlapping thicknesses of plastic plus air at a joint Tee Connectors: used on horizontal and vertical posts and suspension insulator strings when plastic line guards are used on the conductor Available in two ratings: 72.5 kv and 48.3 kv 2475 2373 Part # Description Type ASTM Voltage Class VERSA GUARDS 4.5 Grade Weight (lb.) 2373 ABS/PVC, Eye III 4 2 8.8 2377 ABS/PVC, 4 Stick III 4 1 10.8 2378 ABS/PVC, 6 Stick III 4 1 11.8 VERSA GUARDS 3.92 2389 ABS/PVC, 4 Stick III 4 1 6.1 2689 ABS/PVC, Eye III 4 2 8.1 LINK GUARDS 4.5 2475 ABS/PVC, Eye III 6 2 10.5 2476 ABS/PVC, 4 Stick III 6 1 12.5 2477 ABS/PVC, 6 Stick III 6 1 13.5 33

Class 5 Air Gap Pole Guards Rated max use voltage of 48.3kV guarded phase to guarded phase or 27kV phase to ground Unique Air Gap Design: uniformly spaced dimples help increase insulation and keep electrical leakage to a minimum Type I ABS Plastic: strong memory improves grip when applied to the utility pole Part # Diameter x Length Weight 2486 9 x 6 13.8 lb. 2478 12 x 6 16 lb. Substation Cover-Up & Accessories Often used where outages are difficult to reach and the occurrence of accidental contact is high May be applied with rubber gloves or hot sticks Made from Type I orange ABS plastic Bus Guards: easily interlocked with each other, guard has voltage rating of 36.6kV Bus T Guards: interlock two or three bus guards at bus tap T connections and 90 angles. To interlock units, first position the bus guard, then slide the T guard over the top interlocking the dimples. This guard has a voltage rating of 36.6kV Bus End Guards: cover the ends of a substation bus supported by station post insulators 9992 1374 Part # Dimensions Description ASTM Voltage Weight (lb.) Class Bus Guard 1374 5.25 x 9.5 x 4.5 Impact Resistant ABS Plastic 4 6 Bus T Guard 1375 5 x 15 x 25 Impact Resistant ABS Plastic 4 4 Bus End Guard 9992 8.5 x 12 x 24 UV Resistant High Density Cross Linked Polyethylene 3 5 GUARD ACCESSORIES 816 8 x 16 Hot Cover 4 2.5 4314 15 x 14.25 Underground Distribution 3 2 Elbow Cover 4333 20 x 25 Pole Bracket & Insulator Base 3 2.5 1375 34

Post-Type Insulator Covers Rubber Insulating Blanket - Slotted Rubber Insulating Blanket - Solid Roll Blanket Salisbury s insulating Roll Blankets are made from a high strength fabric reinforced Type II rubber in unique colours making it easy to identify and highly visible in the work area All classes of Roll Blankets are easy to cut, and flexible to -40 F. Highly puncture and tear resistant, each class of blanket is also flame (self-extinguishing), oil, and ozone resistant RLB00 RLB0 RLB1 RLBPVC1 RLBPVC1-48 PTHL PTHS Ozone-resistant Type II orange SALCOR is manufactured from a blend of prime EPDM, offering supreme flexibility Use for covering ridge pins, cross arms with insulators or any place a wire, pin or projection interferes with proper placement of other cover-up devices 1300 Class 4, 28 Eyelets, 36 x 36 1302 Class 4, 2 Hole, 36 x 36 1304 Class 4, 4.5 Hole, 36 x 36 Ozone-resistant Type II orange SALCOR is manufactured from a blend of prime EPDM, offering supreme flexibilty Will maintain colour, flexibility, physical properties, and dielectric strength in the field longer than any other blanket on the market Reinforced, beaded edge Salisbury 900E Class 4; 6 Eyelets; 36 x 36 ASTM 00, Type II, 3 x 30, Brown, 20 lb. ASTM 0, Type II, 3 x 30, Yellow, 26 lb. ASTM 1, Type II, 3 x 30, Yellow/Orange, 36 lb. ASTM 1, 3 x 50, Clear, 60 lb. ASTM 1, 4 x 30, Clear, 48 lb. Covers interlock with 1.5 (38mm) Class 4 Extended Lip SU System or Conventional Line Hose The PTHL cover also has external ribs on the ears which secures 2.5 I.D. line hose Always use clamp pins to secure the device into position The Roll Blankets can be easily custom-cut to fit each application at the job site This minimizes the number of different low voltage blanket sizes and shapes that would otherwise need to be carried from job to job. Each blanket comes in a convenient 36 wide roll Salisbury s insulating Type II rubber Roll Blankets and Insulating Aprons, meet ASTM F2320 standards Part # Description PTHL For insulators up to 16 PTHS For insulators up to 12 35

Arc Protection Blankets Salisbury by Honeywell Arc Protection Blankets are now available in 4 x 5 and 4 x 8 sizes Each size is available in 15kA or 40kA ratings. The 15kA blankets include convenient loops and the 40kA blankets include grommets to easily keep the blanket in place These new blankets are sold individually or with a storage bag or storage bag and tie-strap kit The Arc Suppression Blanket is used as a barrier for protection from the explosive and incendiary effects of electrical arcs and flashes. These hazardous electrical discharges can be caused by faults in cables, in cable splices and joints, and at transformer terminals, or they may be generated by the operation of switchgear, circuit breakers and lightning arresters The blanket can be used for worker protection in underground vaults, switchyards, and other locations where electrical equipment poses a risk of exposure to explosive electrical discharges NOTE: These products do not eliminate or reduce requirements for proper PPE for arc flash protection Part # Dimensions Description ARC45-15 48 x 60 15kA rating - navy blue ARC45-40 48 x 60 40kA rating -gray/khaki ARC48-15 48 x 96 15kA rating - navy blue ARC48-40 48 x 96 40kA rating -gray/khaki Blanket Pins In addition to other uses, blanket clamp pins can be used to hold insulating blankets in place Springs are used for tension while extra holes in the body of the pin are used to grip conductors and prevent line hose from sliding Opens to a full 5.5, making these pins the most versatile on the market Tapered ends to accommodate any clampstick Fiberglass reinforced nylon with rubber tipped pin boots Use HS21 for applications and removal where a 90 angle is necessary Salisbury 21 Salisbury HS21 Blanket Buttons Salisbury B1 For 90o Angle Applications Designed to secure eyelet-style insulating blanket Made of yellow plastic, these buttons snap through the eyelet with thumb pressure on the large head Blanket Canisters 9 x 37 ; holds up to six 36 blankets Molded in bright orange, high impact polyethylene with a tight fitting cap For easy retrieval, blankets can be rolled individually and stored in canister; a single blanket can then be removed without removing any others P2 Fits Blanket Max Size: 36, Dimensions (in): 5 x 37, Capacity: 1-2 Blankets P4 Fits Blanket Max Size: 36, Dimensions (in): 7 x 37, Capacity: 1-4 Blankets P6 Fits Blanket Max Size: 36, Dimensions (in): 9 x 37, Capacity: 1-6 Blankets 36

Chance - Rubber Insulating Covers 36 x 36 Rubber Insulating Blankets Class 4 Will retain its high-visibility orange colour May be used in applications which require a lower class or type Type II ozone/corona-resistant elastomer offers excellent performance properties in accordance with ASTM Standard Specification D-1048 Offers superior resistance to long-term aging/checking C4060346 Solid Blanket 6 eyelets C4060348 Slotted Blanket 28 eyelets Straight Line Hose Does not absorb water Type II ozone/corona-resistant elastometer offers excellent performance properties in accordance with ASTM Standard Specification D-1050-90 C4060296 C4060299 Deadend Cover Class 2, 1.25 diameter, 6 length, 4.55 lb. Class 3, 1.5 diameter, 6 length, 6.22 lb. These covers provide a highly versatile system of covering up a wide variety of configurations on distribution systems The conductor covers couple with the insulator units and deadend units to cover pin-type or post- type insulator construction, virtually surrounding the hot parts and hardware to give line workers extra protection when rubber gloving or using hot sticks Each item is fitted with an adapter for multi-position handling by Grip-All clampsticks Covers couple with Chance 25kV covers, Classes 2, 3, and 4 of rubber line hose and major brands of rubber insulator hoods All covers are bright orange in colour All are made of high density polyethylene in a uniform wall thickness for excellent dielectric/puncture strength Performs well from -50 to 170 F Ultra-violet stabilizers in the material help inhibit degradation as a result of atmospheric exposure Deadend cover fits three 10 diameter porcelain bells or polymer deadend insulators and couples with the line cover To meet the Class 4 rating, the deadend cover must be used in conjunction with a rubber insulating blanket covering the coupler to the line cover Failure to use a blanket to cover the coupler may result in electrical shock, severe injury or death by electrocution Rubber Blanket Buttons Clamp Pins Sold individually For use with any rubber insulating blanket with perimeter eyelets C4060532 C4060530 features eyes and special handle shape for easy placement by clampstick C4060531 features a special handle shape for easy placement by clampstick C4060530 C4060531 Short-Lip Flexible Line Hose Rubber Glove Use Hot Stick Use Does not absorb water Type II ozone/corona-resistant elastometer offers excellent performance properties in accordance with ASTM Standard Specification D-1050-90 C4060306 C4060309 Class 2, 1.25 diameter, 6 long coupler on one end; proof tested at 20kV AC RMS Class 3, 1.25 diameter, 6 long coupler on one end; proof tested at 30kV AC RMS Spiral Conductor Cover Provides extra protection with a wide air space between two thicknesses of solid insulation Made of tough, durable ABS plastic Overall length of each cover is 53 All units interlock with eachother to make up a chain of guards 15/36.6 kv units are formed on the ends to fit over most 15kV insulators, thus eliminating the need for an insulator cover A 4 or 6 long retractable Epoxiglas handle or Clampstick adapter provides for ease of installation from a bucket or platform, in single units or linked together Each double-crossarm unit will fit over two 15kV pintype insulators C4060082GA C4060537 46kV Phase-to-Phase 36kV Phase-to-Phase 37

Chance - Rubber Insulating Covers Pole Covers Prolonged contact with an energized conductor must not be allowed Tested to ASTM F712 Manufactured to ASTM F968 specifications Meet Class 4 requirements Made of high dielectric linear polyethylene material that will not flash flame Helps protect personnel when raising or lowering a pole between energized lines or to cover poles when rubber glove maintenance is performed in relatively confined areas This material will have some softening without deformation at approximately 170 F, and it will resist brittleness at temperatures to -50 F Chance covers are ribbed to reduce cover contact with the pole, thus minimizing creosote contamination Rope handles permit personnel to easily spread the covers and snap them around the pole; rubber gloves must be worn during this procedure 6 Diameter Pole Covers 9 Diameter Pole Covers 12 Diameter Pole Covers C4060550 48 long M4937-1 12 long C4060029 24 long C4060551 72 long M4937-2 24 long C4060030 48 long M4937-4 48 long C4060000 72 long M4937-6 72 long Conductor Cover & Insulator Covers Bright orange in colour 5 long; 25 kv phase-to-phase Maximum conductor size: 666 kcmil ACSR Performs well from -50 to 170 F Available with adapter for hot stick application or without adapter for rubber glove application Provide a highly versatile system of covering up a wide variety of configurations on distribution systems; the units virtually surround the hot parts and hardware to give the linemen extra protection when rubber gloving or using hot sticks Made of high density polyethylene in a uniform wall thickness for excellent dielectric/puncture strength 5 long and are available with a Grip-All adapter for hot stick application or without adapter for rubber glove application Conductor covers mate with insulator covers to cover pin-type or post-type insulator construction; may also be used with the deadend cover Conductor cover will couple with major brands of rubber line hose and insulator covers of the 25kV class 25 kv Phase-to-Phase C4060181 5 Cover, 4 Handle C4060181GA 5 Cover, Grip-All Adapter P4060184 5 Cover Only 36 kv Phase-to-Phase C4060514GA 5 Cover, Grip-All Adapter Cross Arm Cover Prevents tie wires from contacting the crossarm when tying and untying insulators The material used is the same high-dielectric polyethelyne used for Chance conductor and insulator covers Flanges above the slots shield the ends of the double-arming bolts Designed for single or double arm construction, with slots provided for double-arming bolts M4933 Insulator Covers Insulator covers come in two heights; 12 or 16.5 Cover fits 6.5 to 9 diameter pin or post insulators Special slits in the insulator covers help locate the conductor and hardware when installing the covers C4060557 12 Tall 36 kv Phase-to-Phase C4060557L 16.5 Tall 36 kv Phase-to-Phase 38