I3203 WORKSHEET Planned Route: Takeoff: Overhead KNSE Altitude: 16,000 Route: KNSE NUN Approaches: KNPA HI VOR RWY 19 KNPA RNAV (GPS) RWY 19 KPNS VOR RWY 8 Alternate: KMOB via NUN TRADR SQWID Approach: KMOB VOR-A (arcing) Prerequisites: -I3202, SY0302 Syllabus Notes: -None Special Syllabus Requirements: -None Discuss Items a. FMS HILO approach FAA rules for use of a published HILO pattern Selecting appropriate transition (example RNAV 14 at KNSE) o No transition selected o Transition requiring HILO selected o Transition with NoPT selected o HOLDING PAGE with IAF HILO waypoint exit type Automatic Retrievable only from approach database o HOLDING PAGE with Missed Approach holding waypoint Loaded from database along with approach b. FMS procedure turn approach Selecting appropriate transition (example VOR RWY 08 at KPNS) o No transition selected o Transition selected PDF source requirement for Final Approach Segment c. GPS approach FTI procedures d. RVFAC FTI procedures 1
Setting an intercept course in the FMS (example RNAV 11 at KMSY) e. FMS missed approach MISS APR selection o Prior to the MAWP o After the MAWP MISS APR automatic during loaded precision approach (ILS) 2
CNATRAINST 1552.165B IUT T-6B RADIO INSTRUMENTS I3200 BLOCK IUT GRADE SHEET DATE INSTRUCTOR MEDIA: OFT/UTD VT- BRIEF TIME: NAME: EVENT: CTS MANEUVER REF MIF I3201 I3202 13203 1 GENERAL KNOWLEDGE / PROCEDURES 4+ X X X 2 EMERGENCY PROCEDURES 4+ X X X 3 HEADWORK / SITUATIONAL AWARENESS 4+ X X X 4 BASIC AIRWORK 4+ X X X 5 IN-FLIGHT CHECKS / FUEL MANAGEMENT 4+ X X X 6 IN-FLIGHT PLANNING / 4+ X X X AREA ORIENTATION 7 TASK MANAGEMENT 4+ X X X 8 COMMUNICATION 4+ X X X 9 MISSION PLANNING / BRIEFING / 4+ X X X DEBRIEFING 10 GROUND OPERATIONS 4 11 TAKEOFF 4+ X X 12 DEPARTURE 4+ X X 13 INSTRUCTIONAL SKILLS / STUNDENT 4+ X X X MANAGEMENT 41 STEEP TURNS 4 42 IFR UNUSUAL ATTITUDES 4 43 POINT-TO-POINT 4+ X 44 HOLDING 4+ X 45 ENROUTE PROCEDURES 4+ X X 46 ENROUTE DESCENT 4+ X X 47 HIGH-ALTITUDE APPROACH 4+ X 48 TEARDROP APPROACH 4+ X 49 ARCING APPROACH 4+ X 50 HILO APPROACH 4+ X 51 PROCEDURE TURN APPROACH 4+ X 52 RVFAC APPROACH 4+ X X 53 GPS APPROACH 4+ X X 54 PAR APPROACH 4+ X 55 ASR APPROACH 4+ X 56 VOR FINAL 4+ X X 57 ILS FINAL 4+ X 58 LOC FINAL 4+ X 59 GPS FINAL 4+ X 60 BACKUP FLIGHT INSTRUMENT APPROACH 4+ X 61 CIRCLING APPROACH 3+ X 62 MISSED APPROACH 4+ X X X 63 TRANSITION TO LANDING / LANDING 4+ X X X Syllabus Notes: I3201 shall be conducted in the OFT. I3202 and I3203 should be conducted in the OFT, but they may be conducted in the UTD. Discuss Items: I3201 Clearance and departure procedures, lost communications, local procedures/fih, and radar approaches. I3202 FMS flight plan usage, FMS SID, FMS STAR, FMS holding, and FMS arcing approach. I3203 FMS HILO approach, FMS procedure turn approach, GPS approach, RVFAC, and FMS missed approach. 1542.165B Rev 03/16/2017
SE-3, 19 JUL 2018 to 16 AUG 2018 SE-3, 19 JUL 2018 to 16 AUG 2018
SE-3, 19 JUL 2018 to 16 AUG 2018 SE-3, 19 JUL 2018 to 16 AUG 2018
P 7004 X 150 PENSACOLA, FLORIDA NUN VOR APP CRS 108.8 089 Rwy Idg 7000 TDZE 97 Apt Elev 121 AL-318 (FAA) 18200 VOR RWY 8 PENSACOLA INTL(PNS) T A 3 Helicopter visbility reduction below 4 SM NA. CAUTION: Intensive student training invof airport. MISSED APPROACH: Climb to 2000 then climbing left turn to 2600 direct NUN VOR and hold. ATIS 121.25 PENSACOLA APP CON 119.0 269.375 PENSACOLA TOWER 119.9 (CTAF) L 257.8 GND CON 121.9 348.6 CLNC DEL 123.725 256.875 UNICOM 122.95 PENSI CEW 30.8 2047 3000 188 (19.5) 442 SE-3, 19 JUL 2018 to 16 AUG 2018 ELEV 121 R-269 TDZE 314 134 97 269 089 IAF SAUFLEY 108.8 NUN NUN 480 459 241 547 363 MSANU N25NM 3100 220 SE-3, 19 JUL 2018 to 16 AUG 2018 100 17 A 5 211 1800 089 7.3 NM from FAF 8 P 7000 X150 P 26 162 Remain within 10 NM 269 NUN VOR 2000 2600 NUN 146 TWR 201 170 P 0.3% UP 35 223 3000 089 2000 REIL Rwys 8, 26 and 35 TDZ/CL Rwy 17 L HIRL Rwys 8-26 and 17-35 L FAF to MAP 7.3 NM Knots 60 90 120 150 180 Min:Sec 7:18 4:52 3:39 2:55 2:26 PENSACOLA, FLORIDA Amdt 4B 24JUL14 CATEGORY A B S-8 800-1 703 (700-1) CIRCLING 800-1 679 (700-1) 30 28'N-87 11'W 7.3 NM C D 800-2 703 (700-2) 800-2 800-2 1 4 1 679 (700-2) 679 (700-2 4 ) PENSACOLA INTL(PNS) VOR RWY 8
15 R-174 115.7 GCV Chan 104 MOBILE, ALABAMA VORTAC SJI Rwy Idg APP CRS 115.3 TDZE Chan 100 104 Apt Elev N/A N/A 219 AL-267 (FAA) 18088 VOR or TACAN-A MOBILE RGNL(MOB) T ASR MISSED APPROACH: Climb to 900, then climbing right turn to 2000 on heading 200 and SJI R-140 to SAINT INT/BFM 9.2 DME and hold. ATIS 124.75 257.85 MOBILE APP CON MOBILE TOWER GND CON 118.5 269.3 118.3 (CTAF) L 239.0 121.9 348.6 CLNC DEL 119.85 UNICOM 122.95 MSA S J I25 NM 3100 R-284 (IF) TACCU SJI 7 IAF SEMMES 115.3 SJI Chan 100 SE-4, 19 JUL 2018 to 16 AUG 2018 059 239 7 SJI Arc 1800 No PT 1800 104 (7) (IAF) SQWID SJI 7 R-238 365 428 UBACE SJI 5.6 480 R-140 540 373 380 321 744 BROOKLEY 112.8 BFM Chan 75 R-242 SE-4, 19 JUL 2018 to 16 AUG 2018 ELEV 219 062 242 SAINT BFM 9.2 P A 5 304 271 18 from FAF TWR 348 104 5.6 NM 8502 X 150 H H P 4376 X 150 33 H 36 x 283 x A 320 310 5 Remain within 10 NM 1800 284 104 SJI VORTAC 1800 900 2000 UBACE SJI 5.6 hdg 200 SJI R-140 SAINT MIRL Rwy 18-36 HIRL Rwy 15-33 FAF to MAP 5.6 NM Knots 60 90 120 150 180 Min:Sec 5:36 3:44 2:48 2:14 1:52 MOBILE, ALABAMA Amdt 2A 29MAY14 CATEGORY A B C D C CIRCLING 680-1 461 (500-1) 30 41'N-88 15'W 5.6 NM 740-1 1 2 1 521 (600-1 2 ) 780-2 561 (600-2) MOBILE RGNL(MOB) VOR or TACAN-A
SE-3, 19 JUL 2018 to 16 AUG 2018 SE-3, 19 JUL 2018 to 16 AUG 2018
NEW ORLEANS, LOUISIANA WAAS CH 61319 W11A APP CRS 106 Rwy Idg TDZE Apt Elev 10104 4 4 AL-609 (FAA) 17229 RNAV (GPS) Y RWY 11 LOUIS ARMSTRONG NEW ORLEANS INTL(MSY) T For uncompensated Baro-VNAV systems, LNAV/VNAV NA below -1 C (31 F) or above 54 C (130 F). DME/DME RNP-0.3 NA. For inop ALSF-2, increase LNAV/VNAV all Cats visibility to RVR 4000. ALSF-2 A MISSED APPROACH: Climb to 2000 direct ZUBEL and on track 195 to SAFES and hold. D-ATIS 127.55 NEW ORLEANS APP CON WEST 125.5 350.35 EAST 133.15 290.3 NEW ORLEANS TOWER 119.5 254.3 GND CON 121.9 273.525 CLNC DEL 127.2 CPDLC MSA R W 11 3100 25 NM Procedure NA for arrivals on RQR VOR/DME airway radials 055 CW 082. (IAF) RESERVE RQR (IF) FIGUR 2000 122 SC-4, 19 JUL 2018 to 16 AUG 2018 2000 035 (28.2) (3.8) (IAF) Procedure NA for arrivals TIBBY at TBD VOR/DME TBD on V198-552 westbound. ELEV 4 D TDZE 4 2000 106 (7.1) (FAF) KUSTE 259 WEKTA 1.4 NM to 156 RW11 83 RW11 227 219 153 500 SAFES ZUBEL 738 195 174 (8.5) SC-4, 19 JUL 2018 to 16 AUG 2018 354 4 NM 106 to RW11 11 A 16 P 48 10104 X150 H H 85 P TWR P 2 218 94 X A 4 X 20 P 29 7001 X 150 A 5 105 56 2000 GP 3.00 TCH 55 CATEGORY LPV FIGUR DA LNAV/ DA VNAV 106 A 2000 KUSTE 2000 2000 ZUBEL SAFES WEKTA 1.4 NM to RW11 * 500 195 7.1 NM 4.7 NM 1.4 NM B 204/18 C 1 200 (200-2 ) 1 254/24 250 (300-2 ) tr LNAV only. * RW11 D RLLS Rwy 2 TDZ/CL Rwy 11 HIRL All Runways NEW ORLEANS, LOUISIANA Amdt 2B 17AUG17 LNAV MDA 1 340/24 336 (400-2 ) 5 340/26 336 (400-8 ) C CIRCLING 520-1 516 (600-1) 580-1 1 2 600-2 1 576 (600-1 2 ) 596 (600-2) LOUIS ARMSTRONG NEW ORLEANS INTL(MSY) 30 00'N-90 16'W RNAV (GPS) Y RWY 11
APPROACH TRANSITIONS The RNAV 14 approach is selected with no transition Press LSK R6 to view the resulting LEGS
APPROACH TRANSITIONS The IAF MERTY has no /H suffix The HILO holding pattern will not be displayed during the approach
APPROACH TRANSITIONS The RNAV 14 approach is selected with the MERTY transition Press LSK R6 to view the resulting LEGS
APPROACH TRANSITIONS The IAF MERTY has a /H suffix The HILO holding pattern will be displayed during the approach
APPROACH TRANSITIONS The RNAV 14 approach is selected with the PENSI transition This IAF has NoPT published enroute to MERTY Press LSK R6 to view the resulting LEGS
APPROACH TRANSITIONS MERTY has no /H suffix The HILO holding pattern will not be displayed during the approach (NoPT)
HOLD PAGE When an approach transition that uses a published HILO pattern is loaded the exit type is ONCE The second time the aircraft crosses the waypoint it will automatically resume normal sequencing.
HOLDING PAGE SHOWING MAP HOLDING FIX FROM DATABASE HILGA is a missed approach holding fix that is automatically loaded along with it s associated approach procedure : KHBG RNAV Z RWY 3 Exit type is MANUAL. Same as a user generated holding pattern. Once holding fix is crossed automatic waypoint sequencing is suspended until: EXIT is ARMED or NEW ACTICE WAYPOINT is selected
APPROACH TRANSITIONS The VOR RWY 8 approach is selected with the no transition Press LSK R6 to view the resulting LEGS
APPROACH TRANSITIONS Only the waypoints from the FAF inbound will be loaded from the database. All of the waypoints associated with the procedure turn will not be available.
APPROACH TRANSITIONS The VOR RWY 8 approach is selected with the PENSI transition Press LSK R6 to view the resulting LEGS
APPROACH TRANSITIONS With a transition selected, all the relative waypoints are included in the download from the approach database.
Radar Vectors to Final The FMS allows the user to select an intercept course to the FAWP. For orientation purposes it is beneficial to input the FAC as the intercept to display a track line along the FAC. This can be accomplished on the LEGS PAGE
Radar Vectors to Final Download the FAWP (KUSTE) into the scratchpad.
Radar Vectors to Final Upload the FAWP to the active waypoint position ( LSK L1 on PAGE 1)
Radar Vectors to Final At the LSK R6 position the FMS will display GPS computed course from the FAWP to the next waypoint in the sequence. This is the desired INTC CRS Note The GPS computes required courses using great circle routes vice the conventional NAVAID method. As a result This course may be slightly different from the course published on the approach plate. If needed a course can be manually entered via the scratchpad and uploaded using the LSK R6 key To verify the INTC CRS select LSK R6
Radar Vectors to Final Note that the FONT of the INTC CRS becomes slightly larger. Once the modification is made it will only become active when the EXEC button is selected on the UFCP.
Radar Vectors to Final After the change is activated return to the NAV PAGE.
Radar Vectors to Final Now a line extending outward from the FAWP can be seen and used for orientation during vextors to final.
Missed approach procedures Upon reaching the MAP (missed approach point), the FMS will not automatically sequence to, or display any follow-on missed approach waypoints. 125
Missed approach procedures After the MAP, course guidance along the FAC will continue to be provided by the FMS. Once initial missed approach actions are taken (two positive rates gear, above 110 flaps) the additional (follow-on) waypoints can be activated by selecting LSK LR (MIS APR) on the NAV PAGE. 126
Missed approach procedures Once MISS APR is activated, the FMS will display and sequence through any follow on waypoints normally. Here the display shows the need for a right turn to proceed direct to HILGA/H our missed approach holding point which is 15.1 nm behind us. 127
MISS APR If MISS APR is selected prior to reaching the MAWP the track lines to the follow-on waypoints will be displayed in white CDI scale will be reset to 1.0 nm for full scale. Selecting a larger range scale will allow all follow-on waypoints to be displyed.
MISS APR Approach integrity of.3 nm for the final segment is no longer available.
7110.65R AIM CHG 2 12/10/15 3/15/07 5/26/16 pilots operating properly equipped and airworthy aircraft in accordance with operating rules and procedures acceptable to the FAA. Special IAPs are also developed using TERPS but are not given public notice in the FR. The FAA authorizes only certain individual pilots and/or pilots in individual organizations to use special IAPs, and may require additional crew training and/or aircraft equipment or performance, and may also require the use of landing aids, communications, or weather services not available for public use. Additionally, IAPs that service private use airports or heliports are generally special IAPs. FDC NOTAMs for Specials, FDC T-NOTAMs, may also be used to promulgate safety-of-flight information relating to Specials provided the location has a valid landing area identifier and is serviced by the United States NOTAM system. Pilots may access NOTAMs online or through an FAA Flight Service Station (FSS). FSS specialists will not automatically provide NOTAM information to pilots for special IAPs during telephone pre flight briefings. Pilots who are authorized by the FAA to use special IAPs must specifically request FDC NOTAM information for the particular special IAP they plan to use. 5 4 9. Procedure Turn and Hold in lieu of Procedure Turn a. A procedure turn is the maneuver prescribed when it is necessary to reverse direction to establish the aircraft inbound on an intermediate or final approach course. The procedure turn or hold in lieu of PT is a required maneuver when it is depicted on the approach chart, unless cleared by ATC for a straight in approach. Additionally, the procedure turn or hold in lieu of PT is not permitted when the symbol No PT is depicted on the initial segment being used, when a RADAR VECTOR to the final approach course is provided, or when conducting a timed approach from a holding fix. The altitude prescribed for the procedure turn is a minimum altitude until the aircraft is established on the inbound course. The maneuver must be completed within the distance specified in the profile view. For a hold in lieu of PT, the holding pattern direction must be flown as depicted and the specified leg length/timing must not be exceeded. NOTE The pilot may elect to use the procedure turn or hold in lieu of PT when it is not required by the procedure, but must first receive an amended clearance from ATC. If the pilot is uncertain whether the ATC clearance intends for a procedure turn to be conducted or to allow for a straight in approach, the pilot must immediately request clarification from ATC (14 CFR Section 91.123). 1. On U.S. Government charts, a barbed arrow indicates the maneuvering side of the outbound course on which the procedure turn is made. Headings are provided for course reversal using the 45 degree type procedure turn. However, the point at which the turn may be commenced and the type and rate of turn is left to the discretion of the pilot (limited by the charted remain within xx NM distance). Some of the options are the 45 degree procedure turn, the racetrack pattern, the teardrop procedure turn, or the 80 degree 260 degree course reversal. Racetrack entries should be conducted on the maneuvering side where the majority of protected airspace resides. If an entry places the pilot on the non maneuvering side of the PT, correction to intercept the outbound course ensures remaining within protected airspace. Some procedure turns are specified by procedural track. These turns must be flown exactly as depicted. 2. Descent to the procedure turn (PT) completion altitude from the PT fix altitude (when one has been published or assigned by ATC) must not begin until crossing over the PT fix or abeam and proceeding outbound. Some procedures contain a note in the chart profile view that says Maintain (altitude) or above until established outbound for procedure turn (See FIG 5 4 15). Newer procedures will simply depict an at or above altitude at the PT fix without a chart note (See FIG 5 4 16). Both are there to ensure required obstacle clearance is provided in the procedure turn entry zone (See FIG 5 4 17). Absence of a chart note or specified minimum altitude adjacent to the PT fix is an indication that descent to the procedure turn altitude can commence immediately upon crossing over the PT fix, regardless of the direction of flight. This is because the minimum altitudes in the PT entry zone and the PT maneuvering zone are the same. 5 4 28 Arrival Procedures
5/26/16 12/10/15 AIM following systems qualify as a suitable RNAV system: 1. An RNAV system with TSO C129/ C145/ C146 equipment, installed in accordance with AC 20 138, Airworthiness Approval of Global Positioning System (GPS) Navigation Equipment for Use as a VFR and IFR Supplemental Navigation System, or AC 20 130A, Airworthiness Approval of Navigation or Flight Management Systems Integrating Multiple Navigation Sensors, and authorized for instrument flight rules (IFR) en route and terminal operations (including those systems previously qualified for GPS in lieu of ADF or DME operations), or 2. An RNAV system with DME/DME/IRU inputs that is compliant with the equipment provisions of AC 90 100A, U.S. Terminal and En Route Area Navigation (RNAV) Operations, for RNAV routes. A table of compliant equipment is available at the following website: http://www.faa.gov/about/office_org/ headquarters_offices/avs/offices/afs/afs400/afs47 0/policy_guidance/ NOTE Approved RNAV systems using DME/DME/IRU, without GPS/WAAS position input, may only be used as a substitute means of navigation when specifically authorized by a Notice to Airmen (NOTAM) or other FAA guidance for a specific procedure. The NOTAM or other FAA guidance authorizing the use of DME/DME/IRU systems will also identify any required DME facilities based on an FAA assessment of the DME navigation infrastructure. c. Uses of Suitable RNAV Systems. Subject to the operating requirements, operators may use a suitable RNAV system in the following ways. 1. Determine aircraft position relative to, or distance from a VOR (see NOTE 5 below), TACAN, NDB, compass locator, DME fix; or a named fix defined by a VOR radial, TACAN course, NDB bearing, or compass locator bearing intersecting a VOR or localizer course. 2. Navigate to or from a VOR, TACAN, NDB, or compass locator. 3. Hold over a VOR, TACAN, NDB, compass locator, or DME fix. 4. Fly an arc based upon DME. NOTE 1. The allowances described in this section apply even when a facility is identified as required on a procedure (for example, Note ADF required ). 2. These operations do not include lateral navigation on localizer based courses (including localizer back course guidance) without reference to raw localizer data. 3. Unless otherwise specified, a suitable RNAV system cannot be used for navigation on procedures that are identified as not authorized ( NA ) without exception by a NOTAM. For example, an operator may not use a RNAV system to navigate on a procedure affected by an expired or unsatisfactory flight inspection, or a procedure that is based upon a recently decommissioned NAVAID. 4. Pilots may not substitute for the NAVAID (for example, a VOR or NDB) providing lateral guidance for the final approach segment. This restriction does not refer to instrument approach procedures with or GPS in the title when using GPS or WAAS. These allowances do not apply to procedures that are identified as not authorized (NA) without exception by a NOTAM, as other conditions may still exist and result in a procedure not being available. For example, these allowances do not apply to a procedure associated with an expired or unsatisfactory flight inspection, or is based upon a recently decommissioned NAVAID. 5. Use of a suitable RNAV system as a means to navigate on the final approach segment of an instrument approach procedure based on a VOR, TACAN or NDB signal, is allowable. The underlying NAVAID must be operational and the NAVAID monitored for final segment course alignment. 6. For the purpose of paragraph c, VOR includes VOR, VOR/DME, and VORTAC facilities and compass locator includes locator outer marker and locator middle marker. d. Alternate Airport Considerations. For the purposes of flight planning, any required alternate airport must have an available instrument approach procedure that does not require the use of GPS. This restriction includes conducting a conventional approach at the alternate airport using a substitute means of navigation that is based upon the use of GPS. For example, these restrictions would apply when planning to use GPS equipment as a substitute means of navigation for an out of service VOR that supports an ILS missed approach procedure at an alternate airport. In this case, some other approach not reliant upon the use of GPS must be available. This restriction does not apply to RNAV systems Performance Based Navigation (PBN) and Area Navigation (RNAV) 1 2 7
PRIMARY INSTRUMENT NAVIGATION T-6B CHAPTER TEN Procedure For the following example refer to the RNAV (GPS) RWY 32 at Gulfport-Biloxi Intl (see Figure 10-3). Little Dogs Dig Holes Always (LDDHA) is helpful mnemonic for FMS setup. In this example the bearing to IVOLE (the center IF/IAF) is between 043 and 133 and you have been Cleared for the RNAV RWY 32 approach. From this area you are expected to proceed direct to FAROR and may comply with the depicted TAA altitudes. Upon receiving approach clearance: 1. L Load GPS approach. (If not previously accomplished). NOTE Ensure that the appropriate approach transition is selected (FAROR in this example). Where opted, failing to select an appropriate transition will prevent needed waypoints from being loaded to the LEGS Page (IAF, /H (HILO), PT, Arcs or other approach options). 2. D Direct to IAWP, (in this case FAROR). NOTE If being radar vectored to final select FAF (VICKR) as the active waypoint and enter the FAC (313 ) as the Intercept course. Then comply with Radar Vector to Final Approach Course (RVFAC) procedures until cleared for the approach. 3. D Display PFD source should be set to FMS. 4. H Hold If the approach requires a turn in holding (HILO), ensure that the waypoint appears in the legs page with the /H suffix. 5. A Approach Mode Verify APR (approach) mode at 2NM from MAWP on PFD 6. Descend to appropriate altitude per TAA/ATC instructions (cleared for the approach and within 30 nm of FAROR descend to 2000 MSL). 7. Within 5 NM of the IAWP (FAROR), Slow to 150 KIAS. 8. Fly published procedure to establish aircraft inbound to the FAWP (VICKR). 9. Comply with courses and altitudes (use Turn anticipation where appropriate). GPS APPROACH PROCEDURES 10-9
CHAPTER TEN PRIMARY INSTRUMENT NAVIGATION T-6B NOTE In our example, maintain 2000ʹ MSL until FAFWP tracking 043 course from FAROR to the IF IVOLE, then 313 from IVOLE to FAWP VICKR (the published NoPT on this segment indicates that the published HILO pattern should not be executed). 10. Within 5 NM of the FAWP (VICKR) transition to BAC. NOTE Expect handoff to Tower or advisory frequency when inbound to the FAFWP. On initial contact, report position along the approach, gear status and your intentions. 11. At 3 NM from the FAWAP (VICKR) observe HSI SCALES TO CHANGE message. 12. At 2 NM from the FAWP (VICKR) observe transition to APR (approach) mode. NOTE If the FMS fails to transition to the APR MODE notify the Instructor and comply with Loss of GPS integrity prior to the FAWP procedures. 13. At the FAWP execute the 6T s: TIME - As required for any backup approach. TURN - Continue tracking FMS to the MAWP. TIME - Not required. TRANSITION - Set approximately 15% torque, trim for 120 KIAS descent to segment altitude or MDA as required (LNAV MDA 460 MSL). NOTE Adjust pitch to maintain airspeed; use power as required to maintain a stabilized rate of descent not to exceed 1000 fpm. TWIST - Track course from FAC to the MAWP (course is set by the FMS). 10-10 GPS APPROACH PROCEDURES
PRIMARY INSTRUMENT NAVIGATION T-6B CHAPTER TEN NOTES 1. On some approaches, a course change may be required passing the FAWP. 2. Named waypoints on the published instrument approach between the FAWP and MAWP that can be defined using Along-Track-Distance (ATD) from the MAWP or other charted methods may not appear on the NAV/TSD display or on the LEGS page. TALK - As required/directed. NOTE If a GPS Integrity warning occurs between the FAWP and the MAWP, execute the Loss of GPS Integrity Inside the FAF procedures. 14. Approximately 100 prior to the MDA, slowly add power to arrest the rate of descent. 15. At the MDA (460 ), adjust power to maintain altitude and approach speed. 16. Fly at the MDA to the MAWP (RWY32). 17. Upon reaching the MAWP (RWY32), if the runway is not insight or the aircraft is not in a position to make a safe landing, execute the Missed Approach. NOTE The VDP for this approach is defined by distance from the MAWP (1.2 NM prior to RWY32) The FMS will NOT automatically sequence to any waypoints required for execution of the Missed Approach procedure. Automatic sequencing will cease at the MAWP. Once stabilized in the climb and clean, if a Missed Approach is required the pilot must manually sequence the system to the first Missed Approach WPT by selecting MISS APR and EXEC. Until MISS APR is selected the FMS will continue to provide course guidance along the FAC. Common Errors 1. Loading wrong approach/transition. 2. Inappropriate use of feeder fix/taa altitudes. 3. Not slowing to 150 KIAS within 5 NM of the IAWP (for non-radar vectors). GPS APPROACH PROCEDURES 10-11
CHAPTER TEN PRIMARY INSTRUMENT NAVIGATION T-6B 4. Late transition to BAC. 5. Not verifying APR mode within 2 NM of the FAWP. 6. Using wrong Minimums for the approach. 1006. LOSS OF GPS INTEGRITY Prior to the FAWP: If a GPS integrity warning occurs prior to the FAWP, or system sensitivity does not change to APR mode within 2 NM of the FAWP: 1. Transition to a backup approach if available. NOTE This does not, for example, give the pilot the option to fly an ILS approach if the clearance given was to a stand-alone RNAV (GPS) approach. If however, the clearance given was to an overlay approach, the pilot may transition to the underlying NAVAID and continue on the approach. If no backup approach is available (or until obtaining clearance for one); 2. Continue on course to the FAWP. 3. At the FAWP continue to the MAWP maintaining the FAWP altitude. 4. At the MAP, execute the published Missed Approach or climbout instructions as appropriate. Inside the FAWP: NOTE Inform the controlling agency as soon as practical. A GPS integrity warning occurring after the FAWP is a serious situation. Pilots must be prepared to take immediate action. 1. Transition to your backup approach, if available (see note from step one above). 2. Climb to the Missed Approach altitude. 3. Continue tracking to the MAWP. 10-12 GPS APPROACH PROCEDURES
CHAPTER EIGHT PRIMARY INSTRUMENT NAVIGATION T-6B 819. RADAR VECTORS TO FINAL APPROACH COURSE (RVFAC) General Navigate to the final approach course following controller instructions. Description Radar vectors to final approach course is a procedure used by approach control to increase the arrival rate of aircraft by providing vectors onto the final approach course through the most expeditious routes consistent with traffic situations. Although this routing does expedite arrival at your destination, it has one characteristic of which you should be aware the lack of published minimum altitudes until joining a segment of a published approach. Approach control has the statutory responsibility for ensuring terrain clearance while vectoring you for the approach. This is done using Minimum Vectoring Altitude (MVA) charts superimposed on radar displays. Procedure NOTE Pilots should never fully relinquish the responsibility for terrain clearance to an outside agency. Maintain situational awareness and crosscheck terrain clearance altitude by using available NAVAIDS and charts. Never blindly follow vectors from a controller. Be aware of what lies ahead on your assigned heading. If in doubt, query the controller. Fly 200 KIAS on downwind and 150 KIAS on base. If being vectored on an extended final or extended dog-leg to final, maintain 200 KIAS until within 15 NM of the airport (Figure 8-16). 1. Tune and identify the appropriate NAVAID. 2. Check the PFD is configured properly. 3. Set the final approach course into the CDI. 4. Follow radar vectors given by approach control. 5. If a lower altitude is assigned, perform a terminal descent. 6. Transition to BAC: a. When within 5 NM of the FAF and aircraft heading is within 90º of the final approach course. 8-32 TERMINAL PROCEDURES
PRIMARY INSTRUMENT NAVIGATION T-6B CHAPTER EIGHT b. Once established on the FAC and cleared for the approach if no FAF is depicted. 7. When cleared for the approach, maintain the last assigned altitude and heading given by ATC until established on the approach. As the CDI begins to center, and you are cleared for the approach, you are expected to turn onto the final approach course and track inbound. 8. Once established inbound, comply with the remainder of the Low Altitude Instrument Approach Procedures. Common Errors 1. Poor orientation, loss of SA. 2. Not setting the correct NAV source in the PFD. 3. Failure to transition to BAC at the appropriate time. 4. Failure to intercept the approach course once cleared for the approach. Be alert for CDI movement and lead the turn sufficiently to roll out on course. Extended Dog-Leg to final 200 KIAS until 15 nm from airport Extended Straight-in 200 KIAS until 15 nm from airport Base leg 150 KIAS *Transition to BAC when 5 nm from the FAF and aircraft heading is within 90 of the FAC *If no FAF is depicted, transition to BAC when established on FAC and cleared for the approach Downwind 200 KIAS Figure 8-16 RVFAC (FAF Depicted) TERMINAL PROCEDURES 8-33