HAND HELD BALL VALVE & DETENT STYLE BALL VALVES SERVICE PROCEDURE D SERIES J40 SERIES H-VO SERIES D00D SERIES J40 SERIES H-VO SERIES F00 SERIES H-VIT SERIES H-VO SERIES F SERIES F40 SERIES HVIT SERIES TASK FORCE TIPS LLC MADE IN USA tft.com 0 Innovation Way, Valparaiso, IN 4- USA 00-4- -4- Fax -44-
DANGER PERSONAL RESPONSIBILITY CODE The member companies of FEMSA that provide emergency response equipment and services want responders to know and understand the following:. Firefighting and Emergency Response are inherently dangerous activities requiring proper training in their hazards and the use of extreme caution at all times.. It is your responsibility to read and understand any user s instructions, including purpose and limitations, provided with any piece of equipment you may be called upon to use.. It is your responsibility to know that you have been properly trained in Firefighting and /or Emergency Response and in the use, precautions, and care of any equipment you may be called upon to use. 4. It is your responsibility to be in proper physical condition and to maintain the personal skill level required to operate any equipment you may be called upon to use.. It is your responsibility to know that your equipment is in operable condition and has been maintained in accordance with the manufacturer s instructions.. Failure to follow these guidelines may result in death, burns or other severe injury. FEMSA Fire and Emergency Manufacturers and Service Association P.O. Box 4, Lynnfield, MA 040 www.femsa.org
D, F and J Series HAND-HELD BALL VALVES Intended for use with all ball valves constructed of stainless steel with quick-change rear valve seat..0 ITEMS NEEDED Not Supplied In Repair Kit Bench Vise Hammer / Diameter Punch Safety Glasses Drill Press (or electric drill) Loctite.0 INSTRUCTIONS. Remove and discard Hose Gasket (), Rear Seat (), and O-ring ().. Open or close bench vise until there is a gap between the jaws of /4 to /. Prop Valve Handle () over gap so that Spirol Pins () can be driven into the gap between the vise jaws. Drive out the spirol pins using a / diameter punch. Note: Do not use a nail set or pointed punch. This may cause pins to expand, making it very difficult to remove. If possible, remove broken handle at this time. Be sure to wear safety glasses.. Pad vise jaws with several rags. Open valve and place repair mandrel through Valve Ball (). Gently clamp valve in vise with one Trunnion () pointing up. Place allen wrench in end of Trunnion. Unscrew and discard trunnion along with O-ring (). It may be necessary to place a piece of pipe or wrench on end of allen wrench for additional leverage. 4. Turn valve over in vise and repeat step #.. Remove valve from vise and remove mandrel, f40 valve coupling () will need to be removed, Ball (), Front Valve Seat (), and Belleville Washer (4). Discard Valve Seat and Belleville Washer. Note: Earlier models may have an O-ring in place of the Belleville Washer.. Stand valve vertically on drill press and clamp in vise with coupling end up. Drop Belleville Washer (4) into Valve Body () (note orientation in drawing). Drop Front Valve Seat () into Valve Body () (note orientation in drawing). Drop Valve Ball () into Valve Body () and insert plastic mandrel through hole in ball.. Rotate Valve Ball () so that threaded holes are aligned with trunnion hole in Valve Body ().. Install O-rings () on Trunnions ().. Apply a thin film of grease (supplied) to O-rings and Trunnions, take care not to get any grease on the threads. 0. Apply one large drop of Loctite (supplied) on trunnion threads.. Place new Handle () in position over Valve Body (). Make sure that OFF on the handle faces the coupling end of the valve.. Insert Trunnions () through Handle () and Valve Body () while pressing down on the plastic mandrel with drill press chuck or by hand. Note: It will take approximately 0 lb. to compress the Belleville Washer (4). Screw the Trunnion () into Valve Ball (). Do not tighten yet.. Repeat step # with other Trunnion. 4. Clamp one allen wrench in vise with approximately / of the short end above the vise jaws.. Place one Trunnion on wrench in vise and second wrench in other Trunnion. The plastic mandrel should still be in the valve ball. Tighten both Trunnions as tight as you can by hand. Do not use a wrench or pipe on the allen wrench or threads may be damaged.. With the plastic mandrel still in the Valve Ball (), pull the Handle () back to the open or ON position. Locate the small dimple on the Handle () above the Trunnions (). Using the # drill (supplied), drill through the dimple, through the center of the Trunnion (), and out the other side. Support the Handle () below the Trunnions () on the edge of the drill press table or on a pile of boards to insure that the hole passes through the center of the Trunnions ().. Insert the new Spirol Pins () in the drilled holes and press, or gently tap them flush with the Handle ().. Remove plastic mandrel. Lubricate and install O-ring () on Rear Valve Seat (). Press Valve Seat () into Valve Body () (note orientation in drawing). Install new Hose Gasket (). If you have trouble, call -00-4- for advice or send valve and remaining new parts to our service department. Failure to follow these instructions, or poor workmanship voids warranty. * Plastic Repair Mandrels: /4 Waterway (D) - Part number D0 (Included in repair kit D-HRK) Waterway (F00) Part number F00 (Included in repair kit F00-HRK) /4 Waterway Exit (F) - Part number F40 (Included in the F-HRK) / Waterway (F40) Part number F40 (Included in repair kit F40-HRK) * Valve Ball () and Valve Body () are NOT included in repair kits Exploded view drawings and parts lists on following pages
D BALL VALVE 4 0 ** VALVE BODY.0" D0 TRUNNION D040 O-RING-00 VO-00 DQ HANDLE SUBASSEMBLY DQ0 DQ0 CONTAINS SHUTOFF HANDLE D00 BLACK HANDLE COVER HM-BLK - X / BUTTON HEAD SCREW 4 VT0-BH STOP PIN D00 SPIROL PIN V00 WASHER VM40 GRIP SPACER D0 HM-D /- X SOCKET HEAD SCREW VT-SH.0 0 PISTOL GRIP - BLACK HM-BLK /- X / SET SCREW VT-SS PORT PLUG B0 /" SS BALL V 4 BELLEVILLE WASHER D00 FRONT SEAT D00 BALL D00 ** COUPLING.0" D0 O-RING- VO- REAR SEAT D00 GASKET -.0" V040 4
D00D BALL VALVE 4 0 ** 00 VALVE BODY.0" D00 00 TRUNNION F0040 O-RING-0 VO-0 FQ HANDLE SUBASSEMBLY FQ0 FQ0 CONTAINS 00 SHUTOFF HANDLE F000 BLACK HANDLE COVER HM-BLK - X / BUTTON HEAD SCREW 4 VT0-BH 00 STOP PIN F000 SPIROL PIN V00 WASHER VM40 GRIP SPACER F00 HM-F /- X SOCKET HEAD SCREW VT-SH.0 0 PISTOL GRIP - BLACK HM-BLK /- X / SET SCREW VT-SS PORT PLUG B0 /" SS BALL 4 V 4 BELLEVILLE WASHER F000 00 FRONT SEAT F000 00 BALL F000 ** COUPLING 00.0" D00 O-RING- VO- 00 REAR SEAT D000 GASKET -.0" V040
F00. BALL VALVE 4 0 ** 00 VALVE BODY." F00 00 TRUNNION F0040 O-RING-0 VO-0 FQ HANDLE SUBASSEMBLY FQ0 FQ0 CONTAINS 00 SHUTOFF HANDLE F000 BLACK HANDLE COVER HM-BLK - X / BUTTON HEAD SCREW 4 VT0-BH 00 STOP PIN F000 SPIROL PIN V00 WASHER VM40 GRIP SPACER F00 HM-F /- X SOCKET HEAD SCREW VT-SH.0 0 PISTOL GRIP - BLACK HM-BLK /- X / SET SCREW VT-SS PORT PLUG B0 /" SS BALL 4 V 4 BELLEVILLE WASHER F000 00 FRONT SEAT F000 00 BALL F000 ** COUPLING.0" F00 O-RING- VO- 00 REAR SEAT F000 GASKET -." V0
FF & FFP BALL VALVE 4 4 0 ** VALVE BODY." F 40 TRUNNION F4040 O-RING-04 VO-04 4 STOP PIN F0 TAB SHUTOFF HANDLE F0 SPIROL PIN V WASHER VM40 GRIP SPACER F40 HM-J /- X SOCKET HEAD SCREW VT-SH.0 0 PISTOL GRIP - BLACK HM-BLK /- X / SET SCREW VT-SS /" SS BALL V /4- X / SET SCREW VT-SS 4 BELLEVILLE WASHER F400 40 FRONT SEAT F400 40 BALL F400 COUPLING.0" F40 O-RING- VO- 40 REAR SEAT." F400 GASKET -." V0 O-RING-40 VO-40
F40. & J40. BALL VALVE 4 0 ** 40 VALVE BODY." F40 40 TRUNNION F4040 O-RING-04 VO-04 FT HANDLE SUBASSEMBLY FQ0 FT0 CONTAINS 40 SHUTOFF HANDLE F400 BLACK HANDLE COVER HM-BLK - X / BUTTON HEAD SCREW 4 VT0-BH 40 STOP PIN F400 SPIROL PIN V WASHER VM40 GRIP SPACER F40 HM-J /- X SOCKET HEAD SCREW VT-SH.0 0 PISTOL GRIP - BLACK HM-BLK /- X / SET SCREW VT-SS /" SS BALL V /4- X / SET SCREW VT-SS 4 BELLEVILLE WASHER F400 40 FRONT SEAT F400 40 BALL F400 COUPLING.0" F40 40 COUPLING." J40 O-RING- VO- O-RING-0 VO-0 40 REAR SEAT." F400 40 REAR SEAT." J400 GASKET -." V0 GASKET -." V0 O-RING-40 VO-40 O-RING-0 VO-0
DETENT STYLE HAND HELD BALL VALVES This Service Procedure is intended for use with the HVIT, H-VIT, H-VO, H-VOI, H-VO, H-VOI, H-VO, H-VOI and H-VPPIT series of. and. inlet Ball Valves..0 ITEMS NEEDED Not Supplied In Repair Kit Bench Vise T-Handle Allen Wrench Set Loctite.0 INSTRUCTIONS FOR VALVE SEAT AND BALL REPLACEMENT TEAR DOWN:. Remove set screws () from body that are forward of the bail handle. Grasp the front ring (, 4,, or ) in padded vise and remove by unthreading.. Remove the valve seat ( or ) from the male threaded section.. Place the bail handle () in the off position and through the female coupling, push the valve ball ( or ) out the front of the valve. 4. Use a straight blade screw driver to remove the rear valve seat ( or ).. Inspect the o-ring (4 or ) in the front of the valve for damage and replace if required. REBUILD SECTION:. Place a seat ( or ) in the front ring with the male threads.. Install valve seat ( or ) into the body, flat side down.. The notch in the ball ( or ) is designed to reduce turbulence through the valve, install ball with notch down and towards the bail handle side of the valve.. Check for o-ring (4 or ) in the front of the valve, install front ring (, 4, or ) till the shoulder is flush with the front of the body. Compression on the valve is adjusted with the front ring. 0. Cycle bail handle to check for smooth operation. If bail is tight, un-thread front ring. If loose, tighten front ring. Required force to cycle bail is to lbs.. Tighten set screws () evenly. If set screws are not tightened evenly there may be a leak around the front ring seal.. Place ball valve on a pressurized water system and check for leaks and operation..0 INSTRUCTIONS FOR BAIL HANDLE REPLACEMENT REMOVAL OF OLD BAIL HANDLE. Remove set screws () from body that are forward of the bail handle. Grasp the front ring in padded vise and remove.. Remove the valve seat ( or ) from the male thread section.. Place the bail handle () in the off position and through the female coupling, push the valve ball ( or ) out the front of the valve. 4. Use a straight blade screw driver to remove the rear valve seat ( or ).. Inspect the o-ring (4 or ) in the front of the valve for damage and replace if required.. Remove button head screws ( or ) from bail handle.. Push trunnions (4 or ) into the valve body and remove. Note: There is a left and right trunnion on this model, do not mix.. Remove bail handle by lifting up off of the valve body. This will release the detent springs and balls. INSTALLATION OF BAIL HANDLE. Insert one Detent Spring ( or ) and Detent Ball ( or ) into each of the stop lugs of the Bail Handle. Note: ( Make sure the belly shaped side of the handle faces the front of the valve body.). While holding the detent springs and balls in the stop lugs, push bail handle onto valve body over detent area.. Apply lubricant to o-ring ( or ) on trunnion. 4. Align the roll pin ( or ) with the hole in Bail Handle and push from the inside.. Place Trunnion Driver ( or 0) over roll pins.. Apply loctite to the button head screws ( or ).. Install Button Head screws till tight.. Complete steps through in Valve Seat and Ball Replacement Section. Exploded view drawings and parts lists on following pages
HVIT, H-VIT, H-V0, H-VOI, H-VO & H-VOI 0 4 4 4 0 4 4 4 4 4 4 4 4 4 0 44 4 40 4 4 4 44 0
GASKET -." V0 /4- X / SET SCREW VT-SS (SWIVEL) /4- X / SET SCREW VT-SS (LOCK-OUT) /" SS BALL V 4** COUPLING." H4 ** COUPLING." P GASKET -." V0 /4- X / SET SCREW VT-SS BLITZ BASE. H O-RING- VO- 0 /4- X /4 SET SCREW VT-SS0 ** COUPLING." P STREAM STRAIGHTENER P O-RING- VO- 4 O-RING-4 VO-4 ANTI GG RING VO P4 HANDLE SUBASSEMBLY HX BLACK HANDLE COVER HM-BLK HANDLE HX - X / BUTTON HEAD SCREW 4 VT0EBH SPIROL PIN V0 TRUNNION DRIVER HX0 HANDLE SCREW VTE4BH0 DETENT SPRING HM0.4" TORLON BALL VB4TO O-RING- VO- TEFLON TRUNNION SHIM P0 4 TRUNNION - LEFT PL TRUNNION - RIGHT PR DETENT VALVE BODY P0 /- X / SET SCREW VT-SS 0- X / SET SCREW VT0YSS GRIP SPACER HANDLINE HM-H PISTOL GRIP - BLACK HM-BLK 0 WASHER VM40 /- X SOCKET HEAD SCREW VT-SH.0 VALVE BALL SEAT P04 DELRIN VALVE BALL P0 4 O-RING- VO- FRONT END - /" TIP P FRONT END - /" TIP P FRONT END -.0" TIP P FRONT END - /" TIP P4 FRONT END - /4" TIP P FRONT END - /" TIP P TEFLON WEAR RING P VIT FRONT RING LABEL P CAM SCREW HD0 THREAD PROTECTOR RING P 40 GAUGE BUMPER G 4 FRONT RING VO." P0 4 /" SMOOTH BORE INSERT F40 /" SMOOTH BORE INSERT F40 " SMOOTH BORE INSERT F40 -/" SMOOTH BORE INSERT F404 4** FRONT RING VPP." P0 44 VH-4-S0 SMALLEY RING V4 4 BLITZ BRACKET H 4 /4- SS ACORN NUT VTEAC 4 WASHER VW00X- 4 /4- X STUD FULL THREAD 4 VT-ST.0 4 PLAYPIPE HANDLE P 0 SMALL PLAYPIPE BRACKET P ** FRONT RING VO." P0 * - CONSULT FACTORY FOR SPECIFIC PART NUMBERS
H-VO & H-VOI 4 0 0 4 0 /" SS BALL 4 V /- X / SET SCREW VT-SS 0- X /4 SET SCREW VT0YSS0 PISTOL GRIP - BLACK HM-BLK 0 WASHER VM40 /- X SOCKET HEAD SCREW VT-SH.0 0 GASKET -." V /4- X / SET SCREW VT-SS00 ** COUPLING." M0 TOP BAR P4 4 SIDE BAR P40 /- X /4 BUTTON HEAD SCREW 4 VT0-BH0 /" TORLON BALL VB.TO DETENT SPRING P0 STOP LUG P0 SPIROL PIN VP0X.H 0 TRUNNION DRIVER P O-RING- VO- TRUNNION SHIM P0 TRUNNION LEFT PL TRUNNION RIGHT PR 4 DETENT VALVE BODY P VALVE BALL SEAT." P BALL VALVE." P0 O-RING- VO- ** FRONT RING VO."NH P * - CONSULT FACTORY FOR SPECIFIC PART NUMBERS TASK FORCE TIPS LLC MADE IN USA tft.com 0 Innovation Way, Valparaiso, IN 4- USA 00-4- -4- Fax -44-