S405 arbecue ssembly Manual 85-02-6 (G4705) Propane Year limited Warranty Read and save manual for future reference. If pre-assembled, leave this manual with unit for consumer s future reference. For product inquiries, parts, warranty and troubleshooting support, please call -877-707-546. Manual Revision #: 242009 PD
HRDWRE PCK WRNING HEVY RTICLE NEEDS 2 TO LIFT THIS MNUL MUST REMIN WITH THE PRODUCT T LL TIMES To ORDER non-warranty replacement parts or accessories, or to register your warranty, please visit us on the web at www.masterchefbbqs.com CUTION Sharp edges. Wear gloves when assembling your grill. CUTION Read and follow all safety statements, assembly instructions, and use and care directions before attempting to assemble and cook. INSTLLER OR SSEMLER/CONSUMER This manual should be kept with the Q at all times. Failure to follow all of the Manufacturer s instructions could result in hazardous fires, explosions, property damage, or serious personal injury or even death. Follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. Do not try to light this barbecue without reading the Lighting Instructions section of this manual. THIS RUE IS FOR OUTDOOR USE ONLY CONTCT CLL CENTRE IF NY PRTS RE MISSING -877-707-546 NGER. If you smell Gas: a. Shut off gas to the appliance b. Extinguish any open flame c. Open lid d. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department 2. Requires two people to complete the assembly process.. eware of sharp edges. WRNING. Do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance. 2. n LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. TOOLS NEEDED FOR SSEMLY #2 Phillips screwdriver (long and short) ¼ Slotted screwdriver (long and short) djustable wrench Pliers efore assembling the barbecue, read these instructions carefully. ssemble the barbecue on a flat, clean surface. Grill is heavy. You should have at least two people assemble the barbecue together. Notes: Do not fully tighten all the nuts during this initial stage. Caution: Sheet metal can cause injury. Wear gloves when installing the grill. 2 Hinge Pin X Fiber Washer 6 No. 0-24 x 0 Screw X 6 4 5 6 Wheel Spacer 7 8 9 0 6 No. 0-24 x Screw X 6 No. 8-2 x 0 Screw No. 0-24 x 6 Screw X 8 /4-20 x 65 Carriage bolt 4 7 Key # Description prt number Quantity No. 0-24 x Screw 2024-00-06 6 2 No. 0-24 x 0 Screw 2024-000-06 6 No. 0 Nut 224-0000-06 45 4 Hinge Pin G06-0005-9088 5 Wheel Spacer G05-0024-9088 6 No. 0-24 wing nut 00-0000-06 2 7 Fiber Washer G47-0050-9000 26 8 Fiber Washer (lid handle) G06-0027-900 2 9 olt (lid) G06-0004-0 2 0 No. 8-2 x 0 Screw 202-0800-06 2 No. 8 Wing Nut 00-08000-02 2 Venturi clip, side burner G05-0057-9000 No. 0-24 x 6 Screw 2024-006-06 8 4 ST4.2 x 8 Tapping screw 24200-42008-6 0 5 No. 8-2 x 8 Screw 202-0808-06 4 6 /4-20 x 65 Carriage bolt 920-065-06 7 /4-20 Wing nut 00-000-06 8 No. 8-2 Nut 22-08000-06 4 Fiber Washer (Lid Handle) No. 8 Wing Nut ST4.2 x 8 Tapping screw 0 /4-20 Wing Nut 2 5 8 No. 0 Nut 5 No. 0-24 Wing Nut olt (Lid) Venturi Clip, Side urner ST4.2 x 6 Tapping screw No. 8-2 Nut
Parts List (propane) for 85-02-6 (G4705) EXPLODED DIGRM (PROPNE) FOR 85-02-6 (G4705) Key # Quantity Description prt No. Top lid assembly G47-0054-0 Thermometer G05-009-0 C Logo G45-000-0 D 2 Upper hinge G206-0002-2 E Top lid handle G06-0002-0 F 2 Rubber pad G0-008-0 D C D urner box assembly G47-5400-0 2 Lower hinge G20-009-0 C urner G47-5500-0 D Heat shield G47-002-0 E Electrode set, main burners G47-0055-0 F Flame tamers G44-0005-0 G 2 Cooking grates G47-600-0 H Warming rack G47-005-0 EH EG H F D F G E F C C Control panel G47-0056-0 C Valve assembly G47-5800-0 CC Side burner metal hose G44-0059-0 CD Side burner valve G47-005-0 CE Regulator G64-005-0 4 Control knob G06-002-0 CG Electronic Ignitor G40-0008-0 CG2 Electronic Ignitor button G50-0072- CH Grease cup hook G05-004-0 CI Grease cup G40-00-02 ED EE EF DO C CD E CC E E Cart side panel, right G47-0800-0 Cart side panel, left G47-0700-0 DC Upper, back brace G47-00-0 DD Lower, back brace G47-002-0 DE Upper, front panel G47-0057-0 DF Tank Exclusion G47-007-0 DG Lower, front panel G47-0058-0 DH Front, end caps G47-0028-0 DI ack, end caps G47-0029-0 DJ Match holder G40-0079-0 DK Heat shield G20-002-0 DL Tank retainer clip G206-0028-02 DM 2 Wheel G20-008-02 DN Wheel axle G47-0007-0 DO Support bar G47-006-0 DP Right support bracket G47-0062-0 DM DL DJ DK DC DD CH CI CG CG2 DG DE DF CE DP DI C DH E Side shelf table- right G47-600-0 E Side shelf fascia - right G47-0059-0 Side burner table - left G47-6200-0 ED Side shelf fascia - left G47-0060-0 EE Side burner G44-5500-0 EF Electrode wire, side burner G4-004-0 EG Side burner drip pan G04-006-02 EH Side burner grate G0-0022-0 DN DM F HRDWRE PCK F2 SSEMLY MNUL F SFETY ND CRE MNUL F Hardware pack G47-005-0 F2 ssembly instructions G47-M005-0 F Safe Use and Care Manual G207-M05-02 2
SSEMLY INSTRUCTIONS SSEMLY INSTRUCTIONS Two people required for all assembly steps DL DF ssemble the tank retainer clip (DL) to the left cart side panel (), as shown in Figure. Insert the tank exclusion (DF) into the right and left cart side panels ( & ), as shown. Make sure to insert the tank exclusion (DF) into the holes of the cart panels, as shown in Figure C. DE a. ssemble the upper front panel (DE) to the left and right, front cart side panels ( & ), as shown. C 6 7 DE b. ssemble the lower front panel (DG) to the upper front panel (DE) and Cart side panels ( and ), as shown. DG 2 DC ssemble the upper and lower back braces (DC & DD) to both cart side panels, as shown. ack View lower front panel to upper front panel Lower front panel to cart side panel c. ssemble the support bar (DO) to both cart side panels ( & ), as shown. DO X 8 X 8 4 Front View DD DP d. ssemble the right support bracket (DP) to the cart side panel, right (). To assemble, insert the right support bracket (DP) into the holes on the cart side panel, right (), as shown Front View 4 5
SSEMLY INSTRUCTIONS SSEMLY INSTRUCTIONS 4 a. Insert the front and back end caps (DH & DI) to the bottom of the right cart panel (), as shown. 6 a. ssemble the valve assembly (C) to the control panel (C). DH C DI C X DM DN b. Insert the wheel axel (DN) through the first wheel (DM) and the bottom of the left cart panel (). Cone side of the wheel should be against left cart leg, as shown in Figure C. + - b. Remove the Electronic ignition button (CG2) from the electronic ignition (CG). ssemble the electronic ignition (CG) through the back of the control panel (C), as shown. 4 5 DM c. Slide the second wheel (DM) onto the wheel axel (DN) and attach hardware #5 and #4. 5 4 CG C c. Insert one battery into the electronic ignition (CG) battery compartment, with the positive side facing upwards. (attery not included) ttach the electronic ignition button (CG2) to complete assembly. 5 DK C a. ssemble the tank heat shield (DK) to the center support bar located on the left cart side panel (), as shown. C d. ssemble the control panel (C) to the top of the left and right cart side panels ( & ), as shown. 2 4 e. Place the control knobs () onto the stems of the valve assembly (C), located on the control panel (C). C DK 6 7
SSEMLY INSTRUCTIONS SSEMLY INSTRUCTIONS 7 a. ssemble the lower hinge ( x2) on the back of the burner box assembly () as shown. 9 a. ssemble the top lid handle (E) to the top lid (). 7 8 6 X 8 E C b. ssemble the burner (C) to the burner box () by positioning the burner venturi tubes (C) through the openings in the bottom of the burner box (), as shown. Ensure that the burner venturi tubes are facing forward. b. ssemble the thermometer () to the top lid (). 7 8 a. Position the urner box assembly () onto the burner box support brace ( & ) located at the top of the right and left cart side panels. D c. ssemble the upper hinge (D x2) to the top lid assembly (). b. TIP: efore assembling, make sure that the burner venturi tubes (C) engage the valve assembly (C), as shown in figure. D E 7 X 8 c. ssemble the burner box assembly () to the burner box supports ( & ). 7 C IMPORTNT: Ensure that the fiber washers are secured inside the burner box assembly to properly seal the lower casting. 8 9
SSEMLY INSTRUCTIONS SSEMLY INSTRUCTIONS 0 ssemble the lid () to the urner box (), as shown in figure &. 2 Install the hardware into the burner box assembly () to support the flame tamer (F). 9 4 2 7 D E Connect the main burner electrode wire (E), already pre-assembled to the main burner (C), to the electronic ignition (CG), located on the back of the control panel, as shown in figure. F Position the flame tamer (F) onto the hardware assembled in step 2. CG CG 0
SSEMLY INSTRUCTIONS SSEMLY INSTRUCTIONS 4 ttach the grease cup hook (CH) to the bottom of the burner box assembly () as shown. Position the grease cup (CI) into the grease cup hook (CH), as shown. 6 E ssemble right side shelf table (E), and left side burner table () to the left and right cart side panels, as shown. CH CUTION: Failure to assemble grease cup (CI) and grease cup hook (CH) will cause hot grease to drip from the bottom of the burner box, with the risk of fire, property damage, or personal injury. CI E Right side shelf table 5 H a. To assemble the warming rack (H), insert the stationary wire into the holes on the sides of the lid assembly (). Insert warming rack pivot legs (H) into the holes on the inside of the burner box assembly (). Left side burner table Stationary wire Pivot legs b. Place the cooking grate (G) into the burner box assembly (), as shown. H G 2
SSEMLY INSTRUCTIONS SSEMLY INSTRUCTIONS 7 8 a. ssemble the side burner valve (CD) onto the control panel of the side burner table (), as shown. a. ttach the side burner shelf fascia (ED) to the side burner shelf table () and the control panel (C), as shown. CD 0 ED 4 5 8 EE EF b. Place the side burner (EE) into the side burner drip pan (EG) and secure using hardware. X EG ED C E b. ttach the right side shelf fascia (E) to the right side shelf table (E) and the control panel (C), as shown. E 4 5 8 E X C E EH c. Place side burner grate (EH) onto side burner table (E). ttach the control knob () to the side burner valve (CD), as shown. C 4 5
SSEMLY INSTRUCTIONS SSEMLY INSTRUCTIONS 9 a. Use the side burner clip (#2) to secure the side burner orifice to the side burner valve (CD). 20 LP CYLINDER IS SOLD SEPRTELY. Fill and leak test the LP cylinder before attaching to Q. Once LP cylinder has been filled and leak checked, locate the tank support bar on the bottom of the left cart side panel and place LP cylinder in the grooves of the tank support bar. Slide tank retainer clip (DL) over cylinder collar and tighten knob. Connect the regulator (CE) to the gas tank OPD valve. 2 2 X b. Connect the side burner electrode wire (EF) pre-assembled to the side burner (EE) (figure ), to the electronic ignition (CG), located on the back of the control panel, as shown in figure C. EJ EF EF C CG CG 6 7