clinical laboratory Hellendahl staining jar is suitable for holding 76x26 mm slides vertically.

Transcription

1 158 clinical laboratory staining jars Hellendahl & Schifferdecker & Papanicolau Hellendahl staining jar is suitable for holding 76x26 mm slides vertically. Hellendahl staining jar has 9 grooves which can accomodate 18 slides one after the other. Schifferdecker staining jar is suitable for holding 76x26 mm slides horizontally. Schifferdecker staining jar has 10 grooves which can accomodate 20 slides one after the other. Papanicolau (macro) staining jar with stainless steel staining rack is manufactured from thick moulded glass. Staining rack of macro staining jar manufactured from stainless steel. This stainless steel rack has 20 grooves which can accomodate 20 single slides. All staining jar models are supplied with their glass lids. staining jar hellendahl staining jar schifferdecker staining jar papanicolau staining rack macro embedding casettes without lid Disposable plastic tissue cassettes are suitable for holding and identifying tissue samples in processing, embedding and sectioning procedures and fit securely in microtome chuck adapters. Moulded from a high density polymer which is totally resistant to the chemical action of histological solvents. The slanted writing surface accepts markings easily, permitting sample identification. Casette lid is manufactured from high grade stainless steel with perforated surface for optimal liquid diffusion. casette without lid colour white yellow green pink blue stainless steel casette lid. 5 pieces

2 clinical laboratory 159 embedding casettes with lid Have same technical specifications as casettes without lid. The efficient flow-through slots maximize fluid exchange and ensure proper drainage. Lids can be opened and closed as often as necessary and always relock securely without any risk of specimen loss. Large labelling areas are located on both sides of the cassettes. Anterior writing area with 35 angle. Biopsy casettes Square openings allows maximum fluid exchange without having the use of biopsy pads. casette hystology casette biopsy colour white yellow green pink blue embedding sponge for embeddings casettes Manufactured from synthetic sponge with a calibrated porosity that can easily be inserted into the tissue embedding cassettes. Very useful to hold small specimens in biopsy tests and prevent them from being lost during process. embedding sponge sponge 30 x 25 x 2 mm colour blue 1000 pieces tissue base molds stainless steel Manufactured from stainless steel for easy removal of paraffin inclusions. They allow precise location of the specimen into the paraffin. tissue base mold external 55 x 38 x 10 mm 55 x 38 x 10 mm 55 x 38 x 10 mm internal 7 x 7 x 6 mm 15 x 15 x 6 mm 37 x 24 x 6 mm specification biopsy & hystology biopsy & hystology standard 5 pieces 5 pieces 5 pieces

3 160 clinical laboratory urine container with screw cap Manufactured from absolutely clear, high grade polypropylene. With an approximate volume of 100 ml and the approximate volumetric graduations are moulded on the body. The screw cap perfectly fits over the body and avoids any leakage. Non sterile urine containers are packed with caps unattached. Sterile urine containers are originally manufactured under germ-free aseptic (sterile) conditions of class sterile area with extreme sterility control. urine container specification non-sterilized sterilized 1000 pcs 500 pcs urine container with vacuum Manufactured from absolutely clear, high grade polypropylene. With an approximate volume of 100 ml and the approximate volumetric graduations. The screw cap perfectly fits over the body and avoids any leakage. Urine in the container can be transfered via vacuum system. Sterile urine containers are originally manufactured under germ-free aseptic (sterile) conditions of class sterile area with extreme sterility control. Catalogue No: vacuum specification plain with boric acid 100 pcs 100 pcs

4 clinical laboratory 161 feaces container with spoon cap Manufactured from absolutely clear high grade polypropylene. With an approximate volume of 15 ml and approximate volumetric graduations are moulded on the body. The spoon cap perfectly fits over the body and avoids any leakage. Non sterile feaces containers are packed with caps unattached. Sterile feaces containers are originally manufactured under germ-free aseptic (sterile) conditions of class sterile area with extreme sterility control. feaces container specification non-sterilized sterilized 1000 pcs 500 pcs specimen container with press - on cap Manufactured from absolutely clear high grade polypropylene. With a volume of 40 ml and the approximate volumetric graduations are moulded on the body. The press-on cap perfectly fits over the body and avoids any leakage. Non sterile specimen containers are packed with caps unattached. Sterile specimen containers are originally manufactured under germ-free aseptic (sterile) conditions of class sterile area with extreme sterility control. specimen container specification non-sterilized sterilized 1000 pcs 500 pcs

5 162 clinical laboratory micro haematocrit s Manufactured by fully automated systems according to ISO and BS Tube length is 75 mm (+/- 1 mm) and the wall thickness is 0,2 mm. Heparinized s are heparinised with sodium heparinate over internal surface. Non-Heparinized s have blue color code at the end of the micro haematocrit. Heparinised s have red color code at the end of the micro haematocrit. s heparinized s non-heparinized colour code red blue length 75 mm 75 mm in vial 10 vials 10 vials micro haematocrit wax Micro haematocrit wax is non drying, sealing compound placed on a plastic tray. Can be used for fast and safe sealing of the ends of microhaematocrit s. Can be safely stored up to 3 years at room temperature. Up to 48 s (24 on each side) can be stored vertically in numbered positions along the sides of the wax tray. wax pieces

6 clinical laboratory 163 manuel blood lancets Manufactured from medical grade stainless steel. The gamma-sterilized lancets are individually packed. Lancets are very incisive and have very sharp edges which penetrates into the skin very easily. lancets manual pieces 50 pack automatic blood lancets These lancets are user safe since the needle is fully shielded before and after use. They have a pre-loaded, button operated design. These lancets are for single-use only, sterilised by gamma irradiation. Patient comfort due to high quality, ultra sharp tri-bevel needle, high speed penetration of 1.8 mm penetration depth. lancets automatic pack Twist off the protective cap/safety cover Select finger tip insertion site slightly off centre and hold the lancet firmly against site Press the release button to activate the device. Gently massage the finger to obtain the required volume of blood.

7 164 clinical laboratory microscope cover glasses Manufactured from high optical grade, hydrolytic class no: 1, colorless borosilicate glass with an excellent chemical resistance. Thickness of glass used is no 1 (0,13 to 0,17 mm) with the refractive index of n=1,52. Available in 2 types: economical quality superior quality economic quality superior quality x18 mm 20 x 20 mm 22 x 22 mm 24 x 24 mm 24 x 32 mm 24 x 50 mm 24 x 60 mm 10 pack 10 pack 10 pack 10 pack 10 pack 10 pack 10 pack microscope slides Microscope Slides are manufactured from high optical grade soda lime glass with hydrolytic class 3. Their fully automatic production ensures clean, dust and grease free slides. They have extremely flat surface with 1 mm thickness and 26 mm x 76 mm size. Available in 2 types: economical quality superior quality Superior quality colour coded slides has ground edges, with 45 edge angle, with 5 different colours for easy identification. economic quality superior quality specification Cut edges, Plain Cut edges, Frosted one end one side Ground edges, Plain Ground edges, Frosted one end two side Ground edges, Colour Frosted Ground edges, Colour Frosted Ground edges, Colour Frosted Ground edges, Colour Frosted Ground edges, Colour Frosted edge angle 90 Degree 90 Degree 90 Degree 90 Degree 45 Degree 45 Degree 45 Degree 45 Degree 45 Degree colour code white yellow green pink blue 50 pack 50 pack 50 pack 50 pack 50 pack 50 pack 50 pack 50 pack 50 pack

8 clinical laboratory 165 blood counting chambers Manufactured from special optical glass according to DIN standard. With the help of these chambers, it is possible to count leucocytes, erythrocytes, bacteria, thrombocytes, fungus, spore etc. with simple methods under microscope. They are supplied in a polystrene box together with two haemacytometer cover glasses. counting chambers specification Neubauer Improved Thoma Nageotte cover glasses for counting chambers Manufactured from very flat, borosilicate glass with plain ground and polished surfaces. Catalogue No: slide dispenser Slide dispenser can dispense 50 slides at once. By turning the knob, one slide is dispensed for every turn. Catalogue No: forceps for cover glasses Manufactured from stainless steel for handling cover glasses perfectly. forceps cover glass forceps body form curved straight length 105 mm 105 mm

9 166 clinical laboratory slide wallet Manufactured from sturdy thick cartoon for holding up to 20 standard microscope slides of 75 x 25 mm. Made of two parts: a base holding the slides horizontally offering numbered spaces for easy identification and two covers which protect the slides. Removal of slides is done easily by pressing on one end, which will automatically lift the other end. An index for identification of slides is printed on each cover. catalogue no Dimensions 205x340x10 mm Colours white Qty/Pack Qty/Case 5 pieces slide magazine Most convenient, organized and versatile way of storing microscope slides. Can hold up to 200 slides and is stackable for space efficient storage. It includes a slide box and a removable tray. A tinted hinged cover makes the contents of the box easy to see at a glance. All slides are stored in an upright position for easier insertion and removal. Simply tilt them forward and backward with one finger in order to pick up the slide you need. For space saving purposes, you can double the amount of slides simply by storing two slides per slot. For maximum storage space, simply remove the tray and line up 400 slides in 3 rows for long term storage. catalogue no x245x86 mm colour white qty/pack The slide magazine has a removable tray inside the storage box, having a hundred individual numbered slots.

10 clinical laboratory 167 slide boxes with plastic latch Manufactured from high density polypropylene for perfect storage or transportation of standard size slides. Moulded, rigid boxes securely hold slides in grooved slots. These boxes have a safe closing and easy opening lids. Hinged lids are held securely closed by latch lock. The stacking feet maximize stability. They include numbered sheets with a labelling space at the bottom of the case. Both the lining and the slots are numbered to correspond to the slide inventory sheet on the inside cover. slide boxes slide capacity 25 slides 50 slides 100 slides slide boxes with steel latch Same features as above slide boxes, can hold 100 slides. Soft cork lining ensures that slides will not slip. Steel latch provides more secure locking and safety during transportation. Catalogue No: slide mailers Manufactured from high density polypropylene for shipping, storing or staining slides. Flat mailers can holds one, two or three standard (75 x 25 mm and 3 x I") slides securely with large, easy-tosecure snaps. Box type mailer is able to hold five slides. Slotted channels keeps slides separated and enables easy removal. slide mailers slide capacity 1 slide 2 slides 3 slides 5 slides

11 168 clinical laboratory test s glass Test Tubes are made from either neutral glass or heat resistant borosilicate 3.3 glass. Especially boro 3.3 s show excellent stability under temperature changes. 10x75 mm 12x100 mm 13x100 mm 16x100 mm 16x160 mm 18x180 mm 4 x 40 mm s neutral glass wall thickness 0,8/0,9 mm 0,8/0,9 mm 0,8/0,9 mm 0,9/1,0 mm 0,9/1,0 mm 0,9/1,0 mm 0,8/0,9 mm s boro wall thickness 0,9/1,0 mm 0,9/1,0 mm 0,9/1,0 mm 1,0/1,1 mm 1,0/1,1 mm 1,0/1,1 mm test s screw cap Manufactured from thick walled neutral tubings. They are especially useful in culture studies. They have flat screw caps with hermetic closure which provide absolute leak proof. s screw cap x100 mm 16x160 mm wall thickness 1,0 / 1,1 mm 1,0 / 1,1 mm test s plastic Disposable s, manufactured from either polystyrene or crystal clear polypropylene for single use. Available in 2 types: round bottom conical bottom 12x75 mm 12x75 mm 16x100 mm 16x100 mm 16x100 mm 16x100 mm plastic material polystrene polypropylene polystrene polypropylene polystrene polypropylene bottom type round round round round conical conical 1000 pieces 1000 pieces

12 clinical laboratory 169 centrifuge s glass Manufactured from neutral s with a wall thickness between 1,0-1,1 mm. Nominal capacity is approximately 15ml and can stand up to RCF. These graduated s have white inscriptions on them. centrifuge /17x100 mm 16 /17x160 mm wall thickness 1,0 / 1,1 mm 1,0 / 1,1 mm specification non-graduated graduated clamps wood & st. steel Manufactured either from hardened wood with steel spring or from stainless steel with a finger grip. Wood clamp has a total length of 180 mm and can hold s up to 25 mm. Stainless steel clamp has total length 150 mm and can hold s up to 30 mm. clamps clamp type wood st. steel stoppers for s Very effective due to their flange shape and grooved body. Available in different colors (red, green, yellow, blue and also as neutral) and packed as assorted. Very effective due to their flange shape and grooved body. Due to large size flanges, they prevent leakage excellently. catalogue number for s diameter 12 / 13 mm 15 / 16 mm supplied as different colours

13 170 clinical laboratory racks foldable Manufactured from high density polypropylene. Space saving when not in use. Open and close only with simple action. Moulded-in alpha numeric grid reference on the top tier of the rack allows easy sample identification. Due to their weights, they do not float in the water baths. rack foldable diameter mm mm mm mm mm 45 pieces 26 pieces rack 140x 275 x 72 mm 140x 275 x 72 mm 140x 275 x 72 mm 140x 275 x 72 mm 140x 275 x 72 mm Opening the rack Closing the rack Pull the rack appart by holding the holes at top and bottom. Pull side handles out and click into open position. Push side handles in to rack on a flat surface. Press on 4 corners and click into closed position. racks detachable Manufactured from high density polypropylene. Due to their weights, they do not float in the water baths, not even in agitated water. These racks are supplied dismantled and can be easily assembled. A moulded-in alpha-numeric grid reference on the top tier of the rack allows easy sample identification. rack detachable diameter 13 mm 16 mm 20 mm 25 mm 30 mm 90 pcs 60 pcs 40 pcs 24 pcs 21 pcs rows 6 x 15 5 x 12 4 x 10 3 x 8 3 x 7 rack 110 x 250 x 70 mm 110 x 250 x 70 mm 110 x 250 x 70 mm 110 x 250 x 70 mm 110 x 250 x 70 mm colour red blue yellow white green

14 clinical laboratory 171 racks with silicone grips Manufactured from high density ABS which is not recomended for autoclaving. Rack comes as ready unit and no assembly required. Suitable to be used up to 16 mm diameter s. Bottom of each compartment has a silicone gripping finger that holds the at centralised position. Tubes can be inserted and extracted with a gentle push or pull to the. Catalogue No: TURN & POUR Just simply hold the rack and turn it over. The s will not fall out since they are hold bysilicone fingers at the bottom of each compartment. This unique system enables easy and safe unloading of the liquids in the s while the s will not fall down. Bottom of each compartment has a silicone gripping finger that holds the at centralised position. PUSH & EJECT Just simply press the bottom layer of the rack by two hands. The eject mechanism automaticaly releases the s from their positions immediately and also simultaneously. racks stainless steel Manufactured from highest grade stainless steel. This rack is excellent for autoclaving due to the material they are made from. st. steel racks diameter 13 mm 16 mm 18 mm rows 5x10 5x10 4x10 rack 108x210x50 mm 120x230x50 mm 110x240x50 mm

15 172 clinical laboratory screw cap centrifuge s polypropylene Manufactured from FDA approved ultra clear, high grade polypropylene. Can resist centrifugation up to RCF. Autoclavable at 121 C for 20 minutes with the caps not totally closed. DNase, RNase and pyrogen-free sterilised s are manufactured under germ-free aseptic (sterile) conditions with extreme sterility control and then sterilised by gamma radiation. Their conical bottoms make them suitable for centrifugation tests in immunology, microbiology etc. They have flat caps for easy top labelling and with hermetic closure which are absolutely leak proof. The caps have large ridges for increased grip when wearing gloves. A ¾ turn of the cap will be sufficient to close the tightly. Suitable for one hand operation. Graduated in 0,5 ml increments for volume verifications. 15 ml and 50 ml s have also precise volume marks at conical bottom part. Both types have a large and solvent resistant labelling area. CERTIFIED PYROGEN FREE RNASE, DNASE & 15 ml and 50 ml s have also precise volume marks at conical bottom part. Cardboard racks offer a quick solution with the added convenience of disposing after use. Due to the unique cap design a ¾ turn of the cap will be sufficient to close the tightly. Suitable for one hand operation. The caps have large ridges for increased grip. sterilised s are certified as DNase, RNase and pyrogen-free products. certified s are a result of continuous quality control process. catalogue number volume 15 ml 50 ml 50 ml 15 ml 50 ml 50 ml 15 ml 50 ml 50 ml 17 x 120 mm 30 x 120 mm 17 x 120 mm 17 x 120 mm 30 x 120 mm 30 x 120 mm 30 x 120 mm 30 x 120 mm 30 x 120 mm skirt non non yes non non yes non non yes product specifications non sterilised non sterilised non sterilised non sterilised non sterilised non sterilised sterilised - DNA & RNA free sterilised - DNA & RNA free sterilised - DNA & RNA free packing specifications pack in bag pack in bag pack in bag cardboard rack cardboard rack cardboard rack single flow pack single flow pack single flow pack

16 clinical laboratory 173 box cardboard Manufactured from heavy and thick cardboard with inserts. Specially designed to hold screw cap centrifuge s. Suitable for freezing process under low temperature. Printed alpha numeric grid reference on the top tier of the rack allows easy sample identification. box cardboard for s volume 15 ml 50 ml array 7 x 7 4 x 4 total number racks foldable Manufactured from high density polypropylene. Space saving when not in use. Simple and easy action to open and close. Moulded-in alpha numeric grid reference on the top tier of the rack allows easy sample identification. Designed for stable use in water baths. Dimensions 104 x 275 x 72 mm. Rack can hold 2s of 15 ml s and 12 pieces of 50 ml s. Catalogue No: racks snapable Manufactured from high density polypropylene. Very easy to assemble, system snaps together securely. Each row is alphanumerically matrixed for quick identification of s. Designed for stable use in water baths. Dimensions 207 x 171 x 61 mm. Rack can hold 30 pieces of 15 ml s and 20 pieces of 50 ml s. Catalogue No:

17 174 clinical laboratory CERTIFIED PYROGEN FREE RNASE, DNASE & sterilised s are certified as DNase, RNase and pyrogen-free products. certified s are a result of an on going continuous quality control process. available also with five different colours micro centrifuge s standard Made from FDA approved ultra clear, high grade polypropylene. For maximum sample recovery, the interior is highly polished. Autoclavable at 121 C for 20 minutes and can be used between -90 C and 121 C. DNase, RNase and pyrogen-free sterilised s are manufactured under germ-free aseptic (sterile) conditions with extreme sterility control and then sterilised by gamma radiation. Their conical bottoms make them suitable for centrifugation tests in immunology, microbiology etc. They have flat caps specially designed to reduce popping which are absolutely leak proof. Caps are easy to handle and can be opened/closed easily with one hand. All s have graduation marks and large marking area. Tubes can resist centrifugation up to RCF. non sterilized sterilized certified volume 0.5 ml 1.5 ml 2.0 ml 2.0 ml skirt non non non yes micro centrifuge s with safety lock lid s with unique safety lock lid enables sample outstanding stability during centrifugation and perfect sealling. Prevents accidental lid opening during incubation process and also ensures evaporation protection. Similar technical specifications as standard micro s but with a safety lock lid. Unique safety lock lid enables sample outstanding stability during centrifugation and perfect sealling. Prevents accidental lid opening during incubation process and ensures evaporation protection. DNase, RNase and pyrogen-free sterilised s are manufactured exactly similar way as above. non sterilized sterilized certified volume 1.5 ml colour natural skirt non

18 clinical laboratory 175 micro centrifuge Recently improved rubber footplate includes soft feet to increase stability and deadens vibration. This compact mini-centrifuge is ideal for quick spindowns from lube walls and caps. Use to mierofilter cell separations and HPLC samples. Most spins last around 20 seconds, designed for easy repeat opening. Ergonomically designed lid fits on the palm very comfortably. Operation is extremely simple: load s, close lid, and press on/off button. For repeated spins, simply open or close the lid to operate. Internal safety switch ensures unit will not operate with lid open. This personal centrifuge uses minimal benchtop space. Remove cord for compact storage. Unit is ETL, cetl, and CE marked, and complies with European RoHS directive. Maximum speed: 6000 rpm Maximum RCF: 2000 x g Dimensions: 153 x 128 x 104 mm Polyurethane foam case keeps extra rotors and adapters contained and dust-free. Three interchangeable rotors cover all applications - Includes a set of adapters to accommodate aii major micro and PCR styles. Circular rotors and adapters combine to hold up to six micros (0.5 ml, 1.5 ml, 2.0 ml). Straight rotor holds up to 16 PCR s (individual or two strips of 8). Catalogue No: micro grinder pestle Manufactured from high grade polypropylene, autoclavable at 121 C for 20 minutes Excellent for grinding and homogening and resuspending bacterial cells, precipitates of nucleic acids or proteins or tissues in microcentrifuge s. The cone tip has rounded and to fit perfectly to 1.5 ml microcentrifuge s. Packed 10 pieces in a bag. Catalogue No:

19 176 clinical laboratory rotating rack for micro s Manufactured from high density polypropylene which is fully autoclavable. Dimensions: 296 x 118 x 58 mm Rotating rack consists of two separate modules which are attached to each other securely but not able to rotate around their axis. 2 seperate modules are available: 48 holes for 1,5 ml micros on one section and 48 holes for 0,5 ml micros on the other section 48 holes for 1,5 ml micros on one section and 96 holes for 0,2 ml micros on the other section With the rotating rack you can have the below storage combinations: 96 s of 1,5 ml 48 s of 1,5 ml and 48 s of 0,5 ml 48 s of 1,5 ml and 96 s of 0,2 ml 48 s of 0,5 ml and 96 s of 0,2 ml Each row is alphanumerically matrixed for quick identification of s. 0,2 ml s wells are oriented in Standard 96-well format to be used also with PCR transfer trays. Each rotating rack is supplied with a clear polypropylene cover which protects the s from dust and other enviromental negative effects. Supplied as one rack/pack. Catalogue No: Rack storage combination: 96 s of 1,5 ml Rack storage combination: 48 s of 1,5 ml and 48 s of 0,5 ml Rack storage combination: 48 s of 1,5 ml and 96 s of 0,2 ml Rack storage combination: 48 s of 0,5 ml and 96 s of 0,2 ml

20 clinical laboratory 177 racks 4 - side Manufactured from high density polypropylene, with : 174 x 95 x 52 mm. Features a unique system of tabs and slots which facilitate easy connection and sturdy fit. Rack has four sides to hold 4 different combinations: Side (1); holds 4 pieces of 50 ml s Side (2); holds 12 pieces of 15 ml s Side (3); holds 32 pieces of 1,5 ml s Side (4); holds 96 pieces of 0,5 ml s Multi direction racks can be linked together to form multiple racks system. Catalogue No: storage box with lid Manufactured from polypropylene for holding up to 100 pieces of 1.5 and 2.0 ml s and vials. Transparent cover allows to see the content of the box. Moulded grid lines on the lid, imprinted coordinates on the bottom of the base, and imprinted and raised coordinates on each well. Dimensions 141x151x53 mm. Catalogue No: racks 3 tiers Made from moulded polypropylene and can be connected to each other to form series. This rack is designed to store three different size microcentrifuge s at same time. Photo shows 2 racks connected to each other First level has 24 wells to hold 0.2 ml s or strips of 8 or 12 s. Second level has 14 wells to hold 0.5 ml s. Top level has 12 wells to hold 1.5/2.0 ml s. Each row is alphanumerically matrixed and is easy to read. Dimensions 164x123x62 mm. Catalogue No:

21 178 clinical laboratory cryo s CERTIFIED PYROGEN FREE RNASE, DNASE & Made from FDA approved high grade polypropylene. Unique design offers imprinted writing area, graduation marks, silicone rubber sealing ring and self standing base. Cryo s are manufactured under germ-free aseptic (sterile) conditions of class sterile area with extreme sterility control. External threaded vial design allows easier filling to standard cryo boxes and saves %23 more space. sterilised s are certified as DNase, RNase and pyrogen-free products. certified s are a result of an on going continuous quality control process. cryo volume 2.0 ml 4.5 ml skirt yes yes thread external external cryo cap discs Manufactured in different colours to be used with cryo s for enabling easy identification of s from each other. cap disk disc colour blue yellow red green cryo box polycarbonate Manufactured from polycarbonate and can hold 100 cryo s up yo 2,0 mm with an array of 10x10. The forward sloped base and high conrast, imprinted indexing on the transparent lid ensures quick visual orientation. Hinged lid allows easy one handed access to samples. A built in stop prevents the lid from swinging too far when the box is picked up by the lid. All boxes are stackable and also include vent and drainage holes Dimensions are 133x133x53 and each box is supplied with a sample picking tool. Catalogue No:

22 clinical laboratory 179 cryo stand Made from polycarbonate which can withstand both cryogenic freezing and also autoclaving. Orientation of samples is easy with embossed index numbers, squares upper left corner and sloped sides. Dimensions 105x200x23 mm. Catalogue No: cryo box cardboard Manufactured from cardboard with inserts, perfect for storing the samples either in liquid nitrogen or freezers. Box has a dimension of 133 x 133 mm and heigth either 50 mm or 75 mm suitable for all size of cryo s. cryo cardboard box product descriptions for 2 ml s or 5 ml s for 2 ml s or 5 ml s array 10 x x 10 capacity 100 s 100 s cryo canes aluminium Cryo canes are made from aluminium and hold vials for freezer storage or immersion in liquid nitrogene. Cane has a length of 290 mm and can hold five vials upto 2 ml volume. Catalogue No: cryo chilling jar Designed to rapidly chill cryogenic vials in freezer while alcohol filled jar speeds freezing rate. Easily fill jar to visible liquid level graduation with isoporpyl alcohol. Samples are not at all contact with the liquid and insert provides a secure barrier. Jar system can hold up to 2,0 ml vials and consists of polycarbonate jar, polyethylene lid and foam holder. When the samples are removed from freezer, the insulation foam holder decreases warming rate and extends working time. Catalogue No:

23 180 clinical laboratory PCR products & other PCR products PCR products are made out of FDA approved, ultra clear, virgin polypropylene. PCR products are specially designed for thermal transfer and realtime Polymerase Chain Reaction (PCR) applications. PCR products are manufactured in a clean, controlled facility and certificate RNase, DNase and endotoxin - safe on a lot by lot basis. All PCR products are manufactured under germ-free aseptic (sterile) conditions of class sterile area with extreme sterility control. RNase, DNase and PCR inhibitors free. The standard and uniform thin walls of the s provides maximum heat transfer. Specially caps perfectly prevents liquid leakages. The sterilisation certificates are available on website. axygen katalog no PCR-02-C PCR-02-L-C PCR-05-C PCR-0208-CP-C PCR-0208-FCP-C PCR-384M2-C PCR-96-AB-C PCR-96-FLT-C PCR-96M2-HS-C PCR-96-MB-C PCR-AS-200 PCR-SP PCR-TS product description PCR - 0,2 ml - flat cap - clear PCR - 0,2 ml - flat cap - clear - max. recovery PCR - 0,5 ml - flat cap - clear PCR & cap - 0,2 ml - 8 strip - domed cap PCR & cap - 0,2 ml - 8 strip - flat cap PCR plate well PCR plate - 96 well - flat PCR plate - 96 well PCR plate - 96 well - half skirt - amplification PCR plate - 96 well - mega base plate sealing film - aluminium Axyseal Cyclerseal 1000 pieces 1000 pieces 1000 pieces 125 pieces 125 pieces 10 pieces 10 pieces 5 pieces 10 pieces 10 pieces PCR transfer tray Manufactured from high density polypropylene which is fully autoclavable. With : 114 x 74 x 11 mm These trays are thin and easy to carry and designed to rest perfectly over a 96-well rack. A time saver for anyone working with individual 0,2 ml s or strips of 8 and 12 s. With the handles to lift and carry moving the s/strips to thermal cycler is very simple and easy. Catalogue No:

24 clinical laboratory 181 PCR rack Manufactured from high density polypropylene which is fully autoclavable. Excellent rack for before and after PCR sampling. This rack can be used alone or inserted in the workstation. This working/storage rack is designed to accommodate 96 pieces 250 ul PCR s or strips of 8 and 12 s. Tube wells are easly identified with alphanumeric embossed numbers and letters. Translucent clear cover protects the s from dust and has a non-slip surface to allow safe storage of multiple racks. PCR rack for PCR s 0.2 ml (wells) 96 pcs rack 125 x 88 x 31 mm PCR workstation Manufactured from high density polypropylene which is fully autoclavable. This storage/working rack, with lid, is designed to work with different PCR volumes at the same time. It can accommodate up to 32 individual 0.2 ml PCR s, 24 pieces of 1.5 / 2.0 ml and 16 pieces of 0.5 ml micros. Tube wells are alpha-numerically matrixed with raised bold type for accurate sample identification. The rack also has a transparent lid for easy viewing of samples. Frosted writing panels on four sides allow labelling or writing. PCR workstation rack 215 x 118 x 50 mm PCR rack can be inserted and locked in the PCR workstation to form a combine working unit.