Reverse Osmosis system 50 GPD Instruction manual EN
Contents 1. Unpacking 2. Scope of supply 3. Insertion of the membranes 4. Connecting the lines 5. Installation 6. First commissioning 7. Consumables 8. Technical data 9. Assembly and instructions 10. Filter change 11. Filter order 1. Unpacking Remove all packaging material. Make sure that the reverse osmosis system does not show any external damage. 2. Scope of supply 1. smardy reverse osmosis water filter 2. Storage tank 11,35L 3. Water tap 4. Hose line 5. VOTRON Membrane 6. Key for membrane housing 7. Angle valve connection adapter 3/8 x 3/8 + stopcock 8. Clamp for waste water 9. Teflon tape 10. Stopcock storage tank 11. Fixing material
Note: This system is equipped with plug connectors. These enable an easy and secure connection of the hose lines. Insert the hose into the respective opening of the connector until you notice a resistance. Only after the resistance, the hose will be fixed in the anchor. In order to be able to remove the hose again, you will first have to remove the safety clamp On the connector you will see a small white plastic ring. Push it evenly in the direction of the connector and simultaneously pull the hose. 3. Insertion of the membranes Remove the hose from the membrane housing. Unscrew the cover from the membrane housing. (Tool: Key for membrane housing) Then first insert the membrane with the two black rubber rings into the housing. Insert the membrane into the housing up to the stop. Srew the cover back on to the membrane housing. Insert the hose back into connector.
4. Connecting the lines Please connect hose lines as follows: Remove the blue retaining rings from the plug connectors at the Water inlet connection tank Waste water and Osmosis water Now insert the hoses into the connectors. Fasten the blue retaining rings back onto the connectors Water inlet Connection tank Waste water Connection: water armature The scope of supply includes 1 roll of hose, please cut it to the appropiate length.
5. Installation Connect the line with the system Cold water pipe Stopcock Connection water supply Angle valve The scope of supply includes a connector for the water supply as well as the corresponding stopcock. Close the water supply on your angle valve and unscrew the cold water pipe. Then screw the connector for the water supply onto the angle valve. Place 9 to 10 layers of teflon tape around the thread of the stopcock. Then screw the stopcock into the lateral screw opening of the water connection component. On the other side of the connector for the water supply, screw the cold water pipe back on. Now remove the nut from the cockstop and put it over the white hose, which supplies the osmosis system with tap water. Then put the white hose onto the stopcock, the hose has to be put over the protruding ring. Screw the nut back onto the stopcock.
Installation of the water armature: Drill a 12 mm hole through the sink. 1. Put the cover over the threaded rod of the water tap. 2. Put the threaded rod through the drilled hole in the kitchen countertop. 3. Slide the locking washer from underneath over the threaded rod. 4. Now slide the snap ring onto the threaded rod. 5. Screw the lock nut onto the threaded rod and screw down the water tap. 6. Then take the blue hose and put the nut over the hose. 7. Take the sleeve and put it onto the hose. 8. Subsequently take the insert sleeve and stick it into the hose. 9. Now insert the hose into the inner line of the threaded rod and then screw the nut onto the threaded rod.
Water Inlet Determine the assembly site for the waste water clamp. This one must absolutely be positioned over the syphon bend. (the area is marked here in green) Drill a hole in the syphon with a 6mm drill bit. Stick the foam seal around the drilled hole. Fasten the clamp (tighten both screws uniformly). Cut the required length off the hose. Put the nut over the hose. Push the hose into the opening of the clamp. Screw the nut and the clamp together. Connect the hose with the plug connection❸ Installation storage tank
6. First commissioning Before you open the water supply, please double-check all the hose lines. These must have been laid absolutely free of kinks. Open the filter flush valve. It is located before the membrane. Open the water supply (shown here in the green circle) and check all the connections for tightness. Leave the filter flush valve in an open position for approx. 10 minutes. Close the filter flush valve. Open the water tap for 5 min to flush all the lines once again. Subsequently you can enjoy fresh osmosis water
7. Consumables For your system you need the following replacement filters and membranes: item N Description Change interval N 8 Membrane 50 GPD Every 24 months N 9 Activated carbon afterfilter Every 12 months N 11 Sediment filter Every 6 months Daily output 190 L N 12 Activated carbon block filter Every 6 months N 13 Activated carbon sediment filter Every 6 months Just smardy original filters ensure a trouble-free functioning!! 8. Technical data Dimensions: 29cm x 24cm 46cm (LxBxH) Daily filter performance: 190 Liter Water purification without electricity only 3 bar tap water pressure required 9. Assembly and instructions We recommend, to let an installer perform the installation. Incorrect assembly can lead to water damage in the house! The connecting parts are tested and standards compliant. Should you wish to obtain other connecting parts, you can acquire them from us, or from any installation specialist shop. The installation instructions are implementing recommendations for a standard connection. Local regulations for installation and building standards can contain other or additional requirements. The executing installer is responsible for the compliance with applicable rules.
10. Filter change Recommended change interval N 8 12-24 months N 9 12 months N 11 6 months N 12 6 Monate N 13 6 Monate Date: Date: Date: Date: Date: Date: o N 8 Membrane 50 GPD o N 9 Activated carbon afterfilter o N 11 Sediment filter o N 12 Activated carbon block filter o N 13 Activated carbon sediment filter o N 8 Membrane 50 GPD o N 9 Activated carbon afterfilter o N 11 Sediment filter o N 12 Activated carbon block filter o N 13 Activated carbon sediment filter o N 8 Membrane 50 GPD o N 9 Activated carbon afterfilter o N 11 Sediment filter o N 12 Activated carbon block filter o N 13 Activated carbon sediment filter o N 8 Membrane 50 GPD o N 9 Activated carbon afterfilter o N 11 Sediment filter o N 12 Activated carbon block filter o N 13 Activated carbon sediment filter o N 8 Membrane 50 GPD o N 9 Activated carbon afterfilter o N 11 Sediment filter o N 12 Activated carbon block filter o N 13 Activated carbon sediment filter o N 8 Membrane 50 GPD o N 9 Activated carbon afterfilter o N 11 Sediment filter o N 12 Activated carbon block filter o N 13 Activated carbon sediment filter
11 Filter order
Link for accessories: https://www.amazon.co.uk/dp/b06xzyfl5c smardy Robert-Bosch-Str. 6b 86830 Schwabmünchen Germany info@smardy.de