THE COLLECTION by Installation Instructions 0 BIDET FITTING Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ASME A..M U.S. Patent No.,, M Required Tools Roughing-in Dimensions Flat Blade Screwdriver Phillips Screwdriver Tubing Cutter BIDET OUTLINE IS SYMBOLIC (FOR FLUSHING RIM OR SPRAY) / FINISHED WALL *Wrench Adjustable Wrench DOUCHE SPRAY ADJ. -/ TO -/ -/ *Supplied with Fitting MOUNTING BIDET FAUCET CAUTION Channel Locks Turn off hot and cold water supplies before beginning. Place MOUNTING NUTS () onto the VALVE BODIES () and insert VALVE BODIES () through outside holes, from underside of the BIDET LEDGE. Drop the RUBBER RING () over the VALVE BODIES () and thread DECK ADAPTER () onto VALVE BODIE () until it locks against the internal stop. Tighten the MOUNTING NUT () to secure the VALVE BODY (). Remove (), WASHER (0) and UPPER GASKET () from () and insert into the center forward hole of BIDET. -/ -/ -/ MAX. FINISHED FLOOR (C) -/ -/ TO (H) -/ O.D. TAILPIECE -/ -/ FOR GROUND JOINT CONNECTION OR / " O.D. SLIP (INLETS) REAR VIEW WITH WALL REMOVED Replace UPPER GASKET (), and () until it locks against the internal stop. Position the side threaded outlet rearward and secure MOUNTING NUT (). DRAIN INSTALLATION STOPPER BIDET LEDGE HOT 0 COLD Assemble O-RING (), WASHER (), PIVOT ROD () and NUT () to DRAIN BODY (). Concave side of cup WASHER () is toward ball. Thread LOCKNUT (), WASHER () and GASKET () onto DRAIN BODY (). Apply a bead of PUTTY to underside of FLANGE (). Feed DRAIN BODY () up through BIDET and thread FLANGE () fully onto BODY (). Tighten LOCKNUT () firmly, keeping the PIVOT ROD () pointed towards the back of the BIDET. Push DRAIN (0) onto TAILPIECE (). PUTTY BIDET 0 CLIP
SPRAY INSTALLATION TEE AND HOSE CONNECTION Assemble SPRAY BODY () to BIDET. Apply putty to underside of SPRAY BODY FLANGE () to seal and secure with NUT (). Thread SPRAY HOSE () with SEAL WASHER () to SPRAY BODY (). Connect other end of HOSE () with SEAL WASHER () to bottom outlet NIPPLE () of the (). Insert SEAL () into ADAPTER () and tighten ADAPTER () to side inlet of (). Install SEAL () into coupling nut of TEE () and tighten connection to ADAPTER () Connect HOSE COUPLING NUTS () to Hot and Cold valve bodies and securely tighten. Cold Thread SPRAY CAP () onto SPRAY BODY (). PUTTY Hot Front LIFT ROD GUIDE INSTALLATION Unscrew LIFT ROD NUT () from LIFT ROD GUIDE (). Make sure SEAL () is seated into of LIFT ROD GUIDE (). Drop LIFT ROD GUIDE () into rear hole of bidet and from below secure with LIFT ROD NUT (). INSTALL HANDLES LEVER HANDLES: Push ADAPTER () on VALVE STEM (), so that the hole of the ADAPTER () without spline is facing up. See figure "A". Thread HANDLE BASE () onto DECK ADAPTER () Push HANDLE () onto ADAPTER (). Find correct position of HANDLE () by adjusting male teeth on ADAPTER () to female teeth in HANDLE (). DIVERTER KNOB: Install HANDLE ADAPTER () onto valve stem (). Push DIVERTER KNOB () onto HANDLE ADAPTER (). Install RING () onto DIVERTER KNOB ) and tighten with SCREW (0). Press on KNOB CAP (). Secure HANDLE () with HANDLE SCREW (). Push INDEX CAP () in hole of HANDLE (). 0 TOP Figure "A" SPLINE END DOWN M
WATER SUPPLY CONNECTIONS NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE TO BE PURCHASED SEPARATELY Connect water supplies to FAUCET () with /" IPS FLEXIBLE SUPPLIES () or /" O.D. BULL-NOSE RISERS (). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. FINISH DRAIN INSTALLATION Position BIDET fixture and secure to floor. Insert lift rod into lift rod guide. Position EXTENSION ROD () onto POP-UP ROD () and tighten THUMBSCREW (). Remove one end of CLIP () from PIVOT ROD () by squeezing ends together while sliding. Insert PIVOT ROD () into second or third hole in EXTENSION ROD () and reassemble CLIP (). (EXTENSION ROD () may need to be bent.) Adjust STOPPER height by repositioning EXTENSION ROD () and tightening THUMBSCREW (). Using metal TAILPIECE (), make connection to the TRAP (). Cold COUPLING NUT FERRULE TEST INSTALLED FITTING 0 SERVICE With HANDLES () in OFF position, turn on WATER SUPPLIES () and check all connections for leaks. Operate both handles to flush water lines thoroughly. Turn DIVERTOR () to rim wash and bidet spray. Operate Lift Rod () and fill Bidet with water. Check that DRAIN STOPPER () makes a good seal and retains water in Bidet. Adjust stopper height by repositioning Lift Rod () and tightening Thumbscrew (). Release DRAIN STOPPER () and check all drain connections for leaks. Tighten if necessary. To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Remove HANDLE and ADAPTER if present. Remove SPRING CLIP (). Lift STOP WASHER (), turn 0 and replace. Replace SPRING CLIP (). Replace HANDLE ASSEMBLY. SPRAY () may accumulate dirt causing distorted and reduced water flow. Unscrew and remove SPRAY () and rinse clean. Replace SPRAY () and operate handles several times from OFF to ON position. Do not force, handles turn only 0. CARE INSTRUCTIONS: 0 DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE M
THE COLLECTION by M-000A INDEX BUTTON (HOT) M-000A INDEX BUTTON (COLD) -000A HANDLE SCREW M-YYYOA LEVER HANDLE BIDET FITTING MODEL NUMBER -000A HANDLE SCREW M-YYYOA HANDLE M00-YYY0A 0-000A HANDLE ADAPTER -000A HANDLE ADAPTER M-000A DECK ADAPTER KIT 0-000A CARTRIDGE 00-000A TEE AND HOSE KIT (INCLUDING SEALS) 0-YYYOA KIT M-000A VALVE MOUNTING KIT 00-000A MOUNTING KIT 00-000A 00-000A ADAPTER KIT 00-000A COUPLING NUT 0-YYY0A DRAIN STOPPER M-000A LIFT ROD M-YYY0A COMPLETE DRAIN ASSEMBLY 0-YYY0A " FLANGE KIT 0-YYY0A BIDET SPRAY 0-000A PIVOT ROD KIT (-/" lg.) 0-000A SPRAY HOSE CONNECTION KIT 0-000A EXTENSION M-YYY0A LIFT ROD GUIDE 00-000A CLIP HOT LINE FOR HELP For toll-free information and answers to your questions, call: -00-0 Weekdays :00 a.m. to :00 p.m. EST IN CANADA -00--0 (TORONTO -0-0-0) Weekdays :00 a.m. to :00 p.m. EST Product names listed herein are trademarks of American Standard Inc. American Standard Inc. 00 M-000A TAILPIECE INSERT 000-000A TAILPIECE WITH Replace the "YYY" with appropriate finish code CHROME SATIN 00 M
THE COLLECTION by Installation Instructions BIDET FITTING Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ASME A..M U.S. Patent No.,, M Required Tools Roughing-in Dimensions FINISHED WALL Flat Blade Screwdriver Phillips Screwdriver *Wrench Tubing Cutter Adjustable Wrench DOUCHE SPRAY (FOR FLUSHING RIM OR SPRAY) BIDET OUTLINE IS SYMBOLIC / -/ ADJ. -/ TO -/ -/ -/ *Supplied with Fitting Channel Locks MOUNTING BIDET FAUCET Turn off hot and cold water CAUTION supplies before beginning. Place MOUNTING NUTS () onto the VALVE BODIES () and insert VALVE BODIES () through outside holes, from underside of the BIDET LEDGE. Drop the RUBBER RING () over the VALVE BODIES () and thread DECK ADAPTER () onto VALVE BODIE () until it locks against the internal stop. Tighten the MOUNTING NUT () to secure the VALVE BODIES (). Remove MOUNTING NUT (), FRICTION RING (0) and UPPER GASKET () from () and insert () into the center forward hole of BIDET. Replace UPPER GASKET () and FRICTION RING (0). Position the side threaded outlet rearward and secure MOUNTING NUT (). Thread () onto () until it seats against the BIDET LEDGE. BIDET LEDGE HOT 0 COLD -/ -/ MAX. FINISHED FLOOR (C) -/ TO (H) -/ O.D. TAILPIECE DIVERTER AND VACUUM BREAKER ASSEMBLY -/ -/ FOR GROUND JOINT CONNECTION OR / " O.D. SLIP (INLETS) REAR VIEW WITH WALL REMOVED DRAIN INSTALLATION STOPPER Assemble O-RING (), WASHER (), PIVOT ROD () and NUT () to DRAIN BODY (). Concave side of cup WASHER () is toward ball. Thread LOCKNUT (), WASHER () and GASKET () onto DRAIN BODY (). Apply a bead of PUTTY to underside of FLANGE (). Feed DRAIN BODY () up through BIDET and thread FLANGE () fully onto BODY (). Tighten LOCKNUT () firmly, keeping the PIVOT ROD () pointed towards the back of the BIDET. Push DRAIN (0) onto TAILPIECE (). PUTTY BIDET 0 CLIP
TEE AND HOSE CONNECTION SPRAY INSTALLATION Insert SEAL () into ADAPTER () and tighten ADAPTER () to bottom of (). Cold Assemble SPRAY BODY () to BIDET. Using putty, seal underside of SPRAY BODY FLANGE () and secure with NUT (). Install SEAL () into coupling nut of TEE () and tighten connection to ADAPTER () Connect HOSE COUPLING NUTS () to Hot and Cold valve bodies and securely tighten. Hot COUPLING NUT Screw SPRAY HOSE () with SEAL WASHER () to SPRAY BODY (). Connect other end of HOSE () with SEAL WASHER () to side outlet NIPPLE () of the TRANSFER VALVE (). Screw SPRAY CAP () onto SPRAY BODY (). Front LIFT ROD GUIDE INSTALLATION PUTTY Unscrew LIFT ROD NUT () from LIFT ROD GUIDE (). Make sure SEAL () is seated into of LIFT ROD GUIDE (). Drop LIFT ROD GUIDE () into rear hole of bidet and from below secure with ROD GUIDE NUT (). INSTALL HANDLES LEVER HANDLES: Push ADAPTER () on VALVE STEM (), so that the hole of the ADAPTER () without spline is facing up. See figure "A". Thread HANDLE BASE () onto DECK ADAPTER () Push HANDLE () onto ADAPTER (). Find correct position of HANDLE () by adjusting male teeth on ADAPTER () to female teeth in HANDLE (). Secure HANDLE () with HANDLE SCREW (). DIVERTER KNOB: Install HANDLE ADAPTER (0) onto valve stem. Push DIVERTER KNOB () onto HANDLE ADAPTER (0). Install RING () onto DIVERTER KNOB () and tighten with SCREW (). Press on KNOB CAP (). Push INDEX CAP () in hole of HANDLE (). TOP VALVE STEM 0 Figure "A" SPLINE END DOWN M
WATER SUPPLY CONNECTIONS NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE TO BE PURCHASED SEPARATELY. Connect water supplies to FAUCET () with /" IPS FLEXIBLE SUPPLIES () or /" O.D. BULL-NOSE RISERS (). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. FINISH DRAIN INSTALLATION Position BIDET fixture and secure to floor. Insert lift rod into lift rod guide. Position EXTENSION ROD () onto POP-UP ROD () and tighten THUMBSCREW (). Remove one end of CLIP () from PIVOT ROD () by squeezing ends together while sliding. Insert PIVOT ROD () into second or third hole in EXTENSION ROD () and reassemble CLIP (). (EXTENSION ROD () may need to be bent.) Adjust STOPPER height by repositioning EXTENSION ROD () and tightening THUMBSCREW (). Using metal TAILPIECE (), make connection to the TRAP (). Hot Cold COUPLING NUT FERRULE TEST INSTALLED FITTING 0 SERVICE With HANDLES () in OFF position, turn on WATER SUPPLIES () and check all connections for leaks. Operate both handles to flush water lines thoroughly. Turn diverter to rim wash and bidet spray. Operate Lift Rod () and fill Bidet with water. Check that DRAIN STOPPER () makes a good seal and retains water in Bidet. Adjust stopper height by repositioning Lift Rod () and tightening Thumbscrew (). Release DRAIN STOPPER () and check all drain connections for leaks. Tighten if necessary. To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Remove HANDLE and ADAPTER if present. Remove SPRING CLIP (). Lift STOP WASHER (), turn 0 and replace. Replace SPRING CLIP (). Replace HANDLE ASSEMBLY. SPRAY () may accumulate dirt causing distorted and reduced water flow. Unscrew and remove SPRAY () and rinse clean. Replace SPRAY () and operate handles several times from OFF to ON position. Do not force, handles turn only 0. CARE INSTRUCTIONS: 0 DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE M
THE -000A HANDLE SCREW M-YYYOA HANDLE COLLECTION by BIDET FITTING MODEL NUMBER M-YYY0A KIT -000A HANDLE ADAPTER M-000A INDEX BUTTON (HOT) M-000A INDEX BUTTON (COLD) M-YYYOA LEVER HANDLE M0-YYY0A M-000A POP-UP ROD -000A HANDLE SCREW M0-000A M-YYY0A LIFT ROD GUIDE M00-YYY0A M-000A MOUNTING KIT 0-YYY0A DRAIN STOPPER 0-000A HANDLE ADAPTER M-000A ELBOW ADAPTER M-YYY0A COMPLETE DRAIN ASSEMBLY 0-YYY0A " FLANGE KIT M-000A DECK ADAPTER KIT 0-000A PIVOT ROD KIT (-/" lg.) 0-000A CARTRIDGE M-000A ADAPTER KIT M-000A VALVE MOUNTING KIT 00-000A CLIP M-000A TAILPIECE INSERT 00-000A TEE AND HOSE KIT (INCLUDING SEALS) 0-000A EXTENSION 000-000A TAILPIECE WITH 00-000A COUPLING NUT 0-YYY0A BIDET SPRAY HOT LINE FOR HELP For toll-free information and answers to your questions, call: -00-0 Weekdays :00 a.m. to :00 p.m. EST IN CANADA -00--0 (TORONTO -0-0-0) Weekdays :00 a.m. to :00 p.m. EST Product names listed herein are trademarks of American Standard Inc. American Standard Inc. 00 0-000A SPRAY HOSE CONNECTION KIT Replace the "YYY" with appropriate finish code CHROME SATIN 00 M