Enterprise Ventures Corporation Product Line About Enterprise Ventures Corporation Enterprise Ventures Corporation (EVC) is the for-profit affiliate and technology commercialization arm of Concurrent Technologies Corporation (CTC). EVC s mission is to transfer advanced technologies of the highest quality to the industrial base and deliver cost-effective services to its clients. EVC achieves its mission by linking its success with the success of its clients, employees, partners, and the communities where it operates. EVC, together with our parent company, CTC, can provide full life cycle support services from design and integration through disposition. These services can be provided for a wide array of products ranging from specialized tooling through complex launch and handling systems.
Carriage, Stream, Tow, and Recovery System The Carriage, Stream, Tow, and Recovery System (CSTRS) was designed to support the U.S. Navy s requirement to provide an Organic Airborne Mine Countermeasures Capability from an MH-60S Helicopter and the Littoral Combat Ship (LCS). CSTRS will enable the LCS to readily respond to mine threats, providing an extra measure of safety for crew and ships during shallow water missions. In addition, the CSTRS design is modular and is capable of supporting the deployment requirements of both towed and non-towed mine sensors that provide a wide range of mine countermeasure techniques. EVC has provided manufacturing support for the production of the first 11 CSTRS shipsets delivered to the Navy. EVC is currently manufacturing CSTRS shipsets for the Navy, and the manufacturing of these articles is anticipated to last 5+ years, leading into product sustainment efforts including repair and spare part fabrication.
Quick Skive Removal Tools Quick Skive Removal Tools consist of various hand tools and power tools with ergonomically-designed handles that use specially-engineered, nonmetallic blades, gap blades, and gap bits specifically designed for removing materials from fragile, scratch-prone surfaces. The blade and bit materials and angles were originally designed for small area removal of stubborn stealth materials and gap fillers from aircraft fuselages and components for on-and off-aircraft repair applications. Quick Skive Handle Quick Skive Removal Tools have Quick Skive Kit multiple applications for aviation and industry, allowing for outstanding results when a worker-friendly heat/ skive process is used directing a heat gun or other heat source on the targeted surface, then skiving off the heated materials. Aviation: Remove specialty materials, gap fillers, and sealants from fuselages, access panels, and fuel tanks without damaging the underlying primer coating or the substrates. Approved for use on U.S. Air Force (USAF) military aircraft. Industrial: Clean sealants and fillers without scratching steel, aluminum, fiberglass, composite, glass, and other delicate surfaces. Benefits: Enables faster rate of material removal for repairs Allows for simple one-person operation Avoids damage to base primer, substrate, or metal treatment Prevents secondary waste Eliminates dust residue NOTE: Quick Skive Removal Tools are only to be used by trained professionals with adequate aviation or industrial experience and in accordance with the safety guidelines. 2
Quick Skive Handle (P/N 08376A01) The Quick Skive Handle is made with DuPont Rynite 935 thermoplastic for great durability and has a Neoprene rubber-padded grip. Designed to comfortably fit in the user s hand, the Quick Skive Handle reduces fatigue and prevents injury. The Quick Skive Handle works exclusively with Quick Skive blades, featuring a quick-disconnect capability allowing the user to quickly change between blade types. Quick Skive blades are sold separately. Quick Skive Handle Ergonomic thermoplastic handle with neoprene rubber grip 08376A01 Quick Skive Impact Tool (P/N 08824A01) The Quick Skive Impact Tool is specifically redesigned for gap filler removal. Consisting of a commercial-off-the-shelf (COTS) ergonomic, rubber comfort-grip handle and hardened steel shaft for great impact durability, the plastic cover modification protects the tool head from damaging the substrate, while the aluminum end cap creates a larger strike area for striking with a rubber or plastic mallet. The Quick Skive Impact Tool works exclusively with the Quick Skive gap bits, featuring a quick-disconnect capability allowing the user to quickly change between bit sizes. Quick Skive gap bits are sold separately Quick Skive Impact Tool Comfort grip, ergonomic handle with internal metal shaft and metal end cap for impact applications 08824A01 Quick Skive Pneumatic Removal Tool (P/N 08567A01) Save time and labor when removing specialty materials and stubborn gap fillers from aircraft without damaging the substrate by using the Quick Skive Pneumatic Removal Tool. Redesigned for aircraft coating and gap filler removal, the quick Skive Pneumatic Removal Tool consists of a COTS tool manufactured by Florida Pneumatic, with a modified head specifically designed for use with Quick Skive blades. The Quick Skive Pneumatic Removal Tool operates at a pressure of 90 pounds per square inch gauge pressure (maximum), and comes with an external air flow valve. Average air consumption is 4.5 cubic feet per minute. Air inlet is 1/4 female pipe thread, and minimum air hose size is 3/8 inner diameter. Quick Skive blades are sold separately. Quick Skive Pneumatic Removal Tool Air powered, variable stroke removal tool 08567A01 Quick Skive Blade Holder (P/N 09108H01) The Quick Skive Blade Holder is made from a soft rubber material designed to comfortably fit in the user s hand and prevent injury. The multipurpose blade holder is great for use in tight spaces and hard-to-reach areas, and can also be used as a blade cover to protect the sharpened blades from damage when not in use. Quick Skive blades are sold separately. Quick Skive Blade Holder Palm-size, rubber blade holder/blade cover 09108H01 3
Quick Skive Blades and Bits Quick Skive blades, gap blades, and gap bits are made of non-metallic materials that will not damage substrates or delicate surfaces when used properly. The special blade and bit materials and angles were explicitly designed for removing tough, elastomeric materials, sealants, and gap fillers from fragile, scratchprone surfaces on aircraft fuselages and components. The Quick Skive blades listed below are specifically designed for removal of elastomeric materials and work exclusively with the Quick Skive Handle, Quick Skive Pneumatic Removal Tool, and Quick Skive Blade Holder. PEEK blade (1.250 ) 50 angle single-sided cut; blade tip width is 1.250 08463H01 PEEK blade (0.750 ) 50 angle single-sided cut; blade tip width is 0.750 08463H02 Ultem blade (1.250 ) 50 angle single-sided cut; blade tip width is 1.250 08464H01 The Quick Skive gap blades and gap bits listed below are specifically designed for removal of gap filler materials. The Quick Skive gap blades work exclusively with the Quick Skive Handle, Quick Skive Pneumatic Removal Tool, and Quick Skive Blade Holder. The Quick Skive gap bits work exclusively with the Quick Skive Impact Tool. Ultem gap blade (0.230 ) Ultem gap blade (0.200 ) Ultem gap blade (0.170 ) Ultem gap blade (0.140 ) Ultem gap blade (0.120 ) Ultem gap bit (0.120 ) Ultem gap bit (0.100 ) blade tip width is 0.230 blade tip width is 0.200 blade tip width is 0.170 blade tip width is 0.140 blade tip width is 0.120 hexagonal-shaped bit body. Bit tip width is 0.120 hexagonal-shaped bit body. Bit tip width is 0.100 08464H02 08464H03 08464H04 08464H05 08464H06 08978H04 08978H03 4
Quick Skive Blade Sharpening System (P/N 08832A01) The Quick Skive Blade Sharpening System, designed specifically for sharpening Quick Skive blades, consists of two blade slots accurately set to sharpen single-sided blades at a 50 angle and double-sided blades at 25 /25 angles. Blade sharpening is accomplished accurately every time in just minutes. The Quick Skive Blade Sharpening System has a 650 revolutions per minute flat turntable with an 8 diameter abrasive disc encased in a metal cover for added safety. The safety cover can be removed easily for quick-change capability of the abrasive disc.* The equipment operates at a quiet 60 decibels and weighs only 25 pounds. Certified to meet Canadian Standards Association and Underwriters Laboratories Inc. electrical requirements, the system is compatible for use in Canada and the USA only. * Note: Safety cover must always be replaced before operating the blade sharpening system. Quick Skive Blade Sharpening System Electrically powered, small, portable blade sharpening device 08832A01 Quick Skive Kit (P/N 08470A01) The Quick Skive Kit contains an assortment of 8 blades and a Quick Skive Handle, as listed below. Qty Item Part Number 2 PEEK blades (1.250") 08463H01 2 PEEK blades (0.750") 08463H02 2 Ultem gap blades (0.230") 08464H02 2 Ultem gap blades (0.170") 08464H04 1 Quick Skive Handle 08376A01 1 Case with custom foam insert 08471A01 Quick Skive Kit 08470A01 Quick Skive Deluxe Kit (P/N 08470A02) The Quick Skive Deluxe Kit contains an assortment of 12 blades, 8 gap bits, Quick Skive Handle, Quick Skive Impact Tool, and Quick Skive Blade Holder, as listed below. Qty Item Part Number 2 PEEK blades (1.250 ) 08463H01 2 PEEK blades (0.750 ) 08463H02 2 Ultem gap blades (0.230 ) 08464H02 2 Ultem gap blades (0.170 ) 08464H04 2 Ultem gap blades (0.140 ) 08464H05 2 Ultem gap blades (0.120 ) 08464H06 2 Ultem gap bits (0.120 ) 08978H04 2 Ultem gap bits (0.100 ) 08978H03 1 Quick Skive Handle 08376A01 1 Quick Skive Blade Holder 09108H01 1 Quick Skive Impact Tool 08824A01 1 Case with custom foam insert 08471A02 Quick Skive Deluxe Kit 08470A02 5
H-60 Bridge Tool Set H-60 Bridge Tool Set H-60 Bridge Tool Set (P/N 07180A01) The H-60 Bridge Tool Set contains 17 specially-designed tools for the removal and installation of the forward and aft bridge assemblies on the MH-60. Using hands-on input from MH-60 maintainers, these tools are purpose-built using materials and coatings to allow for zero maintenance-induced damage while enabling a significant reduction in the time required to perform removals and installations. Benefits: Improves maintainer effectiveness and efficiency Reduces total maintenance hours Protects aircraft components from maintenance-induced damage Improves aircraft availability Qty Item Part Number 1 H-60 Bridge Tool Set 07180A01 6
Incremental Sampling Tool Kit Incremental Sampling Tool Kit (P/N 08564A01-00) Incremental soil sampling for environment field studies typically requires the collection of 30 to 100 individual soil increments per sample design. Each increment must be the same depth and volume. The Incremental Sampling Tool Kit contains everything needed for incremental soil sampling, enabling users to quickly and effortlessly collect increments in a variety of soil types consistent with current U.S. EPA Method 8330B guidance. The Incremental Sampling Tool Kit is solidly constructed of stainless steel to support high-production incremental sampling field studies. Its reinforced fabrication is specifically designed to handle the demands of the environmental industry. The Incremental Sampling Tool Kit includes the items listed below. Qty Item Part Number 1 Stainless steel Incremental Sampling Tool with rubber grip handles 1 Plunger rod handle 1 Rounded retainer snap pin 1 Locking carrying case with (2) keys 2 Looped T-handle hex key 1 0.750-inch diameter x 2.50-inch long coring bore cutter and plunger 1 1.000-inch diameter x 2.50-inch long coring bore cutter and plunger 1 1.250-inch diameter x 2.50-inch long coring bore cutter and plunger 1 1.625-inch diameter x 2.50-inch long coring bore cutter and plunger Incremental Sampling Tool Kit 08564A01-00 Incremental Sampling Tool Kit Ms. Michele Adams Contractual POC Ph: 814-269-2794 Email: Michele.Adams@evc.ctc.com 100 CTC Drive Johnstown, PA 15904-1935 www.evc.ctc.com Order Contact Information: Enterprise Ventures Corporation Cage Code: 3RWH7 DUNS NUMBER: 065104155 05/15