www.somfy.com Sunea screen io Ref. 506559C ES PT EL Installation guide Guía de instalación Guia de instalação
CONTTS. Introduction. Safety.. Safety and responsibility. Installation.. Mot preparation.. Tube preparation.. Mot/tube assembly 5.. Installing the tube-mot assembly 5. Wiring 5 5. Commissioning 5 5.. Identifying setting steps already completed 5 5.. Pre-programming the Somfy io local control point 6 5.. Checking the mot s direction of rotation 6 5.. Setting the end limits 6 control point 8 5.6. Checking the settings 8 6. Operation 8 6.. Standard operation 8 6.. Operating with a Somfy io sens 8 7. ADDITIONAL settings 9 7.. Favourite position (my) 9 7.. Adding/Deleting Somfy io control points and io senss 9 7.. Modifying end limits 9 7.. Advanced functions 0 8. Tips and recommendations 8.. Questions on the Sunea screen io? 8.. Replacing a lost broken Somfy io control point 9. Technical data. INTRODUCTION The Sunea screen io mot is designed to drive all types of lateral arm-mounted awnings and vertical awnings (with without cassette). What is io-homecontrol? The Sunea screen io uses io-homecontrol, the new universal and secure wireless communication protocol, shared by the maj manufacturers in the wld of home automation. io-homecontrol enables all comft and security equipment to intercommunicate and be actuated via one single control point. system mean that it keeps in step with your changing requirements. You can start by automating roller shutters and the front do, then equip the outside awnings, the gate and garage do garden lighting with the io-homecontrol system. These scalable items of equipment are still compatible with the existing system, thanks to io-homecontrol technology, which ensures their interoperability. F further infmation please visit the website www.io-homecontrol.com io-homecontrol provides advanced and secure radio technology that is easy to install. io-homecontrol labelled products communicate with each other, improving comft, security and energy savings. www.io-homecontrol.com Copyright 0 Somfy SAS. All rights reserved.
. SAFETY.. Safety and responsibility Befe installing and using this product, please read these instructions carefully. This Somfy product must be installed by a professional motisation and home automation installer, f whom these instructions are intended. Meover, the installer must comply with current standards and legislation in the country in which the product is being installed, and infm his customers of the operating and maintenance conditions f the product. not covered by the guarantee. In this event, as f all usage not consistent with the instructions given herein, Somfy accepts no responsibility f harm damage. equipment and accessies... In addition to the safety instructions described in this guide, be sure to also observe the instructions set out in the attached document «Safety instructions to follow and keep». ) Switch off the mains supply f the awning befe OFF perfming any service operation in the vicinity. To avoid damaging the mot: ) Never immerse it in liquid! ) Avoid impacts! ) Do not drop it! 5) Never drill holes in it! 6) Avoid moving the awning if ice has fmed on it. 5 6. INSTALLATION The Sunea screen io must be installed in a location sheltered from inclement weather... Mot preparation ) Fit the crown (A) and the drive wheel (B) to the mot. ) Measure the length (L) between interi edge of the mot head and the rim of the drive wheel. L = A B L.. Tube preparation ) Cut the roller tube to the required length. ) Deburr the roller tube and remove the swarf. Ø > 6 Copyright 0 Somfy SAS. All rights reserved.
.. Mot/tube assembly ) Slide the mot into the roller tube. with x Ø 5 mm self-tapping screws x Ø.8 mm steel pop rivets located at least 5 mm from the outer rim of the drive wheel (L - 5) and at most 5 mm from the outer rim of the drive wheel (L - 5). 5 mm 5 mm The screws pop rivets must only be attached to the drive wheel and not to the mot... Installing the tube-mot assembly Insert the end-piece into the tube.... Star head mot: ) Fit the tube/mot assembly to the end bracket (C). ) Fit the tube/mot assembly to the mot bracket (D).... Round head mot: ) Mount the suppt on the mot head, and then the ) head rail. L C 0 mm D. WIRING Always make a loop in the power supply cable to prevent water entering the mot! Comply with current standards and legislation when installing. - Cut off the mains power supply. - Connect the mot accding to the infmation in the table below: OFF 0 V ~ 50 Hz x 0,75 mm x,5 mm 0 V ~ 50 Hz Mot cable Brown Live (P) Blue Neutral (N) Yellow/Green Earth ( ) 5. COMMISSIONING The guide only describes commissioning using a Situo io type Somfy io local control point. F commissioning using any other io control point, refer to the cresponding guide. 5.. Identifying setting steps already completed Only one mot should be powered at a time. Switch on the power and follow procedure «a» «b», accding to the awning s reaction: ON Copyright 0 Somfy SAS. All rights reserved. 5
a The end limits are set and no io control point has been programmed. Go to the section. b Press the Up Down button, and follow procedure «b» «b» accding to the awning s reaction. b The end limits are not set and no io control point has been programmed. Go to the section. Programming the b b b The awning is fully raised lowered The end limits are set and the io control point has been programmed. Go to the section. 5.. Pre-programming the Somfy io local control point - Press the Up and Down buttons simultaneously: the awning will make a brief movement; the Somfy io local control point has been pre-programmed into the mot. 5.. Checking the mot s direction of rotation ) Press the Up button on the Somfy io local control point: a) If the awning is raised, the direction of rotation is crect: go to the section. b) if the awning is lowered, the direction of rotation is increct: press the «my» button until the awning moves; ) Press the Up button to check the direction of rotation. a b 5.. Setting the end limits The end limit setting depends on the type of awning. 5... awnings F vertical awnings without upper stop, lateral arm-mounted awnings without head rail, the upper and lower end limits must be set. 6 Copyright 0 Somfy SAS. All rights reserved.
Setting the upper end limit ) Position the awning at the upper end limit. Press and hold the Up button f > s to raise the awning in one continuous movement. ) Stop the awning at the desired point. ) If necessary, adjust the position of the awning using the Up Down buttons. ) Press the «my» and Down buttons simultaneously: the awning will be lowered in one continuous movement, even after the «my» and Down buttons have been released. awning, and go to the section. 5 Sunea screen io Setting the lower end limit ) Put the awning in the lower end limit position. Press and hold the Down button f > seconds to lower the awning in one continuous movement. ) Stop the awning at the desired point. ) If necessary, adjust the position of the awning using the Up Down buttons. ) Press the «my» and Up buttons simultaneously: the awning will be raised in one continuous movement, even after the «my» and Up buttons have been released. awning. 6) Press the «my» button again until the awning moves: the end limits have been programmed. Go to the section. 5... 5 6 F awnings with upper stop (load bar stopped under the head rail), the upper end limit is automatically adjusted, while the lower end limit must be set. Setting the lower end limit Do not press the «my» and Down buttons simultaneously to reach the lower end limit ) Put the awning in the lower end limit position. Press and hold the Down button f > seconds to lower the awning in one continuous movement. ) Stop the awning at the desired point. ) If necessary, adjust the position of the awning using the Up and Down buttons. ) Press the «my» and Up buttons simultaneously: the awning will be raised in one continuous movement, even after the «my» and Up buttons have been released. awning. 6) Press the «my» button again until the awning moves: the end limits have been programmed, go to the section. 5 6 Copyright 0 Somfy SAS. All rights reserved. 7
Sunea screen io 5.5. 5.5.. Using a pre-programmed Somfy io local control point - awning will make a brief movement; the control point has been programmed. 5.5.. After a single power cut ) Press the Up and Down buttons simultaneously on the new control point until the awning moves. awning will make a brief movement; the control point has been programmed. 5.6. Checking the settings PROG PROG - Check the settings of the upper and lower end limits using the Somfy io local control point. 6. OPERATION 6.. Standard operation 6... Besides the upper and lower positions, an intermediate position known as the «favourite position (my)» may be programmed in the mot. To program, modify delete the favourite position (my), see the section «Additional settings». To use the favourite position (my): - move, and stop in the favourite position (my). my my 6... STOP function The awning is moving. - automatically. 6... Up / Down buttons 6.. Operating with a Somfy io sens 6... Refer to the cresponding guide. 6... Refer to the Somfy io wind sens guide f details of its operation. Reaction of the awning to the wind rising When the wind rises, the awning will start to move up to the upper end limit. It is impossible to prevent the awning from closing, to lower it while the wind is still blowing. Reaction of the awning to the wind dropping When the wind has dropped, a manual down der may be issued via the io control point after 0 seconds. However, all automated systems will remain locked f mins. 6... Feedback After each der, the Sunea io sends a message. This response is processed by the io two-way control points. 0 s 8 Copyright 0 Somfy SAS. All rights reserved.
7. ADDITIONAL SETTINGS 7.. 7... The procedure to follow f programming modifying the favourite position (my) is identical. ) Put the awning in the desired favourite position (my). ) Press the «my» button until the awning moves: the desired favourite position (my) has been programmed. my 7... ) Press the «my» button: the awning will start to move, and stop in the favourite position (my). ) Press the «my» button again until the awning moves: the favourite position (my) has been deleted. 7.. Adding/Deleting Somfy io control points and io senss Refer to the cresponding guide. 7.. Modifying end limits 7... awnings F vertical awnings without upper stop lateral arm-mounted awnings without head rail, both Readjusting the upper end limit ) Position the awning at the upper end limit. ) Press the Up and Down buttons simultaneously until the awning moves: the mot is in setting mode. ) Adjust the awning s top position using the Up Down buttons. ) Press the «my» button until the awning moves: the new upper end limit has been programmed. Readjusting the lower end limit ) Position the awning at the lower end limit. ) Press the Up and Down buttons simultaneously until the awning moves: the mot is in setting mode. ) Adjust the awning s bottom position using the Up Down buttons. ) Press the «my» button until the awning moves: the new lower end limit has been programmed. 7... F awnings with upper stop (load bar stopped under the head rail), the upper end limit is adjusted Readjusting the lower end limit ) Position the awning at the lower end limit. ) Press the Up and Down buttons simultaneously until the awning moves: the mot is in setting mode. ) Adjust the awning s bottom position using the Up Down buttons. ) Press the «my» button until the awning moves: the new lower end limit has been programmed. Copyright 0 Somfy SAS. All rights reserved. 9
Sunea screen io 7.. compatibility of your installation. 7... This function releases the fabric tension after closing an awning with upper stop (load bar stopped under the head rail). The procedure to follow to activate deactivate «Back release» is identical. F safety reasons, this function can only be activated deactivated via the io control point in scenarios: After the -second settings validation stop and befe f the next cycles. After a single power cut, and f the next cycles. To activate this function: ) Put the awning in the upper end limit position. ) Press the «my» and Down buttons simultaneously until the awning moves. - If the «Back release» function was inactive, it is activated. - If the «Back release» function was active, it is deactivated. 7... This function can be used to increase decrease the load bar s fce under the head rail, with thresholds (high-medium-low). The mot s default facty setting is medium level. F safety reasons, this function can only be accessed via the Somfy io control point in scenarios: After the -second settings validation stop and point. and f the next cycles. After a single power cut, and f the next cycles. To activate this function: ) Put the awning in the middle position. 0.5 s 5 s simultaneously, then immediately afterwards press and hold the «my» and Up buttons until the awning moves. The mot is in programming mode f just 0 s. ) Adjust the closing fce using the Up Down buttons. - To increase the closing fce, press the Up button until the awning moves slowly: the cassette awning closing fce is increased to the upper threshold. - To decrease the closing fce, press the Down button until the awning moves slowly: the cassette awning closing fce is decreased to the lower threshold. ) Press the «my» button until the awning moves: the new closing fce has been programmed. 0 Copyright 0 Somfy SAS. All rights reserved.
8. TIPS AND RECOMMDATIONS 8.. Questions on the Sunea screen io? Possible causes Solutions The awning does The wiring is increct. Check the wiring and modify it if necessary. not operate. The mot is hot. Wait until the mot cools down. The awning stops too soon. An increct cable has been used. The io control point battery is low. The control point is not compatible. The io control point used has not been programmed into the mot. The crown is increctly positioned. The end limits have been increctly set. Check the cable and ensure it has leads Check whether the battery is weak and replace it if necessary. Check f compatibility and replace the control point if necessary. Use a programmed control point program this control point. Fit the crown crectly. Readjust the end limits. 8.. Replacing a lost broken Somfy io control point Refer to the cresponding guide. 8.. This reset deletes all control points, all the senss and all the end limit settings, and resets the mot s direction of rotation and favourite position (my). However, the advanced functions («Back release», «Closing fce») are maintained. Only switch off the power f the mot to be reset. ) Put the awning in the middle position (if possible). ) Cut the power supply f seconds. OFF ) Switch the power supply back on f 5 to 5 seconds. ) Cut the power supply f seconds. sec. 5) Switch the power supply back on: the awning moves f several seconds. 5 sec. ON OFF If the awning is at the upper lower end limit, it will make a brief movement. 5 sec. sec. movement followed by a second a few instants later. The 5 ON - Repeat the procedures from the» section 6 my Copyright 0 Somfy SAS. All rights reserved.
9. TECHNICAL DATA Radio frequency Power supply 868-870 MHz io-homecontrol, two-way Tri-band 0 V ~ 50 Hz Operating temperature - 0 C to + 70 C Index protection rating IP Maximum number of associated control points and senss Safety level 9 Class I Copyright 0 Somfy SAS. All rights reserved.