Aquafax Section Contents Plastic Seacocks & Pipe Fittings SECTION 2- Forespar Marelon Seacocks & Valves 4 Forespar Marelon Hose Connectors & Smart Valves 5 Forespar Vented Loops & Diverter Y Valves, Marelon Skin Fittings 6 KM Fittings Nylon Skin Fittings 7 KM Fittings Diverter Valves, Hose Connectors, Deck Fillers & Pump Out Fittings 8 Safi Plastic Fittings & General Hose Connectors Five Depots Nationwide Aquafax Limited, 4 Dencora Way, Sundon Business Park, Luton, Beds LU HP Tel:(0582) 568700 Fax:(0582) 568720 Aquafax Ltd. (Hamble), 2- Mitchell Point, Ensign Business Park, Hamble, Southampton SO 4RF Tel:(02) 80457206 Fax:(02) 80457208 Aquafax Ltd. (Plymouth), Unit 5 Plymouth Trade Park, 22 Macadam Road, Plymouth PL4 0RU Tel:(0752) 669944 Fax:(0752) 667764 Aquafax Ltd. (Middlewich), Unit, Valley Court, Sanderson Way, Middlewich, Cheshire CW0 0GF Tel:(0606) 84 Fax:(0606) 8488 Aquafax Ltd. (Wroxham), Unit Littlewood Lane, Stalham Road Ind. Estate, Hoveton, Norfolk NR2 8DZ Tel:(060) 7888 Fax:(060) 7898 CATALOGUE I SECTION
Forespar Marelon Seacocks Aquafax FORESPAR S MARELON INTEGRATED PLUMBING SYSTEM Reinforced Marelon is a formulation of glass reinforced dupont zytel. Exceeding ABYC recommendations and meeting all UL standards; its unique design provides easy installation in a wide variety of valve configurations. All Marelon integrated valves are sold as a complete system. The assembly consists of thru-hull, valve body and tailpipe barb or female pipe thread end. The thru-hulls use a Buttress style thread for exceptional strength and are not compatible with any other valves. Thru-hulls cannot be sold or used separately. All valves have one part number for the complete assembly. Each valve is factory assembled and pressure tested. Forespar cannot be held responsible for valves disassembled and modified or reassembled improperly. REINFORCED PLASTIC SEACOCKS SERIES 9 Special Features Non Corrosive: Long term reliability Compact: Ease of installation Serviceable: Even afloat Easy to operate: Positive action High impact strength Non conductive Fire resistant: test details available UV Resistant: Temp. range -20 C to +80 C Not affected by bilge cleaners, gas, diesel or oils In case of an emergency; all non-screened thru-hull style valve are supplied with a handle cap/bung that is designed to plug the thru-hull from the outside. This plug can be put in place while vessel is in water. The valve can then be removed from the king-nut and any blockage cleared. Warning - Never leave a boat unattended while bung is in place and valve disassembled. This bung plug is for temporary use only. The bung can also be used during Winter storage to keep debris from collecting inside thru hull. Per ABYC/UL requirements, a flat surface approximately the same diameter as the king-nut is needed inside the hull for proper installation. All valves are full port. The I.D of the hose barb is carried thru the ball so there is no restriction of flow. Dimensions on request. Mushroom Illustrated Counter Sunk Illustrated Mushroom Illustrated Counter Sunk Illustrated SEACOCK Mushroom outboard fitting. Part No. Hose Connection -806 BSP -8062 BSP -806 " BSP -8064 BSP -8065 BSP -8066 2" BSP SEACOCK Mushroom outboard fitting Part No. Connection -80 Hose straight -802 Hose straight -80 " Hose straight -804 Hose straight -805 Hose straight -806 2" Hose straight SEACOCK Countersunk outboard fitting. Part No. Hose Connection -807* BSP -8072* BSP -807* " BSP -8074* BSP -8075* BSP -8076* 2" BSP Countersunk outboard fitting. Part No. Connection -804* Hose straight -8042* Hose straight -804* " Hose straight -8044* Hose straight -8045* Hose straight -8046* 2" Hose straight Mushroom outboard fitting Countersunk outboard fitting. Part No. Connection Part No. Connection -802 Hose r/angle -805* Hose r/angle -8022 Hose r/angle -8052* Hose r/angle -802 " Hose r/angle -805* " Hose r/angle -8024 Hose r/angle -8054* Hose r/angle -8025 Hose r/angle -8055* Hose r/angle -8026 2" Hose r/angle -8056* 2" Hose r/angle SEACOCK - L Port type with two connectors inboard Mushroom outboard fitting Countersunk outboard fitting. Part No. Connection Part No. Connection -8020 Hose -8022* Hose -80202 Hose -80222* Hose -8020 " Hose -8022* " Hose -80204 Hose -80224* Hose -80205 Hose -80225* Hose -80206 2" Hose -80226* 2" Hose 2 SECTION
Aquafax Forespar Marelon Valves & Skin Fittings REINFORCED PLASTIC SEACOCKS & VALVES VALVE MAINTENANCE All Forespar valves are non-corrosive, but like any moving part in a marine environment, they require regular inspection and lubrication. Actuate the handle and lubricate the seals on a regular schedule using Forespar LanoCote Part No. 5-7779 (see page 5). MARELON VALVES WITH BSP STYLE THREADS SPECIAL SERIES 9 SEACOCK Threaded BSP parallel into the King Nut allowing fitting to Bronze skin fittings and also for hose connections. MARELON VALVES Designed to meet the needs of builders and owners who require the benefits of the Marelon integrated plumbing system, with BSP style threads. BALL VALVES Precision moulded in Marelon with P.T.F.E. seals. After,000 operations a valve was submerged in water and pressure tested to 80 P.S.I. The result was leak free and no evidence of wear on internal seals. Threaded BSP parallel. Part No. Size 2-808 " BSPF Straight 2-8084 BSPF Straight 2-8085 BSPF Straight 2-8086 2" BSPF Straight Part No. Size -8007* BSP -80072* BSP -8007* " BSP -80074* BSP -80075* BSP - - Part No. Hose -8008* -80082* -8008* " -80084* -80085* -80086* 2" Part No. Hose -8009* -80092* -8009* " -80094* -80095* -80096* 2" See Section 2 for Bronze Skin Fittings Part No. Thread Body Ø Length OA -8000 76mm 00mm -80002 76mm 00mm -8000 " 2mm 40mm -80004 25mm 50mm -80005 0mm 95mm -80006 2" 50mm 205mm MARELON VALVES WITH 2 OR HOSE CONNECTIONS On/off only. Diverter valve with positions. FLOWTECH TM PERFORMANCE VALVE Part No. Hose Size -802* -8022* -802* " -8024* -8025-8026* 2" Part No. Hose Size -8024-80242 -8024 " -80244* -80245* -80246* 2" LOCKING HANDLE OPTION Forespar offers an optional locking plate installed at the factory on any 9 series integrated seacocks. These locking plates allow the handle to be set in the closed position and a padlock (not supplied) used to positively lock the valve closed. Satisfies USCG requirements. For Part No.s add LD i.e. -806LD TO ORDER ONLY ONLY AVAILABLE TO ORDER FOR "AND 2" SERIES 9 VALVES. ASK FOR WRITTEN QUOTATION. Note: Aquafax can supply the padlock (see Section 7). Valve locks are not sold separately and are not a retrofit item. Flowtech TM free flow sea valves incorporate the valve body, thru-hull and the choice of all three sizes of hose pipe connectors all in one set. These high performance valves are available for (9.05mm), " (25.4mm) & (8.mm) hose sizes. The Flowtech TM valve can be faired smooth to the boats outer skin so that when the valve is closed, the internal plunger and valve pipe creates a flush, fair and fast outer surface. Made of Marelon. Part No. -80045 Valve components are not compatible with any other manufacturers products. SECTION
Forespar Marelon Hose Connectors Aquafax FORESPAR SMART VALVE FORESPAR SMART VALVES The Smart Valve provides the safety and assurance of a visual display panel showing which seacock is open or closed without having to go below and pull up floorboards to make a visual inspection. Factory installed sensors are mounted on the valve using state of the art sensing technology to monitor the valves handle position. The display panels use red and green LED lights to indicate which valve is open (green LED) or closed (red LED). Panels are available in 4, 8 or 2 valve combinations and valve identification names engraved on each panel (e.g Head intake). Description Part No. Forespar Smart Valve Panel 2V 4 Way 2-8090 Forespar Smart Valve Panel 2V 8 Way 2-809 Forespar Smart Valve Panel 2V 2 Way 2-8092 Forespar Smart Valve Panel 24V 4 Way 2-8095 Forespar Smart Valve Panel 24V 8 Way 2-8096 Forespar Smart Valve Panel 24V 2 Way 2-8097 TO ORDER ONLY Check for Delivery Times Forespar Smart Panels are supplied to order only as a 2 or 24 Volt kit and should be ordered with Forespar Seacocks. Add an S to indicate smart valve to the end of the part number (e.g -806S). FORESPAR VALVE ROV TM REMOTE OPERATED VALVES Using powerful sealed motors, valves can be opened and closed with the touch of a button from the control panel AVAILABLE ON REQUEST - ASK FOR DETAILS & WRITTEN QUOTATION REINFORCED PLASTIC MARELON FITTINGS 2 HOSE CONNECTORS Part No. BSP Hose A B C -8040 5 8" 25 25 57-80402 25 26 6-8040 " " 7 27 75-80404 42 2 8-80405 7 6" 42 2 8-80406 2" 2" 44 2 8 WATER STRAINERS It features an integral mounting bracket and clear polycarbonate lid for ready inspection. The stainless steel strainer basket can be easily removed for cleaning. Ports: BSP. Height: 55mm. Dia. 60mm. Part No. Description -80055 BSP Strainer -86246 BSP - " hose connector -86248 BSP - hose connector -86250 BSP - hose connector -80065 BSP - BSP reducing bush ELBOWS Two versions available, male thread/hose, female thread/hose Part No. Item A B C D E -804 5 8" 5 8-8042 2 54 42-804 " " 6 6 47-8044 22 70 54-8045 26 8 70-8046 2" 2" 8 90 8 Part No. Item A B C D E -8042 2 5 8" 5 42-80422 2 54 45-8042 2 " " 6 6 48-80424 2 22 70 6-80425 2 28 78 70-80426 2 2" 2" 9 90 8 2 4 SECTION
Aquafax Forespar Marelon Skin Fittings VENTED LOOPS & DIVERTER Y VALVES VENTED LOOPS Installing a vented loop will ensure that fluids will not siphon from a tank or the sea. Vented loops are commonly used in the marine toilet system and engine cooling system. The simple valve system incorporated in the top of the loop allows air to enter the line when not in use, yet effectively seals as water or other fluid passes through. Molded in Marelon, neither vent nor loop will corrode. The duckbill one way valve is designed to seal properly if particulate matter is present in fluids. Hose Size Height Width Part No. 5 (.4mm) 4 (08mm) -80750 5 8" 4 (4.mm) 4" (0.6mm) -8075 4 (4.mm) (95.mm) -80752 " 7" (7.8mm) 9" (228.6mm) -8075 8" 7" (7.8mm) 9" (228.6mm) 2-80754 -8075 5 (.4mm) 7 (96.6mm) -80755-8075 -80022-8002 LANOCOTE CORROSION CONTROL DIVERTER Y VALVES Forespar Diverter Y Valves and connectors are moulded from Marelon. Y Valves are an essential piece of equipment when the flow of water or other fluids are required to be conveniently diverted, as in marine head application where a holding tank is utilised. Hose Size Height Width Depth Part No. 7 (85mm) 8" (205mm) (89mm) -80022 " (92mm) 4" (99mm) (89mm) -8002 8" (92mm) 8 (26mm) (89mm) 2-80024 (92mm) 4" (05mm) (89mm) -80025 Y CONNECTORS Moulded in Marelon. Flange mounting. Projection: 60mm. Suitable for up to 80 P.S.I. Flange Diameter: 89mm Prevents thread freeze-up Prevents electrolysis corrosion Seals porus surfaces Neutralizes acids, alkalies, salts LanoCote 4oz jar Part No. 5-7779 Spare Vent Cap and Duck Bill Assembly Part No. -80752- Hose Size Part No. " -800-8005 They are easily mounted to a bulkhead The valves are operated by a simple 20º movement Positive stops are provided between positions Available in three versions. Precision moulded in high strength glass reinforced Marelon. Makes them suitable for either above or below waterline. -800 REINFORCED PLASTIC SKIN FITTINGS LanoCote is the choice of marine professionals for long term corrosion control. It is extremely effective in preventing and stopping corrosion on all types of metals under all environmental conditions. Formulated to withstand salt water marine conditions, LanoCote is particularly useful in preventing thread seizure due to all types of corrosion on boats and machinery. Applied during assembly, LanoCote will greatly assist in easy dismantling years later. MUSHROOM HEAD Part No. Hose Size -8050 5 8" -80502-8050 " -8050A 8" -80504-80505 -80506 2" MUSHROOM HEAD BSP Part No. Thread Length -805 2" -8052 2-805 " 2 8" -8054 " -8055 " -8056 2" " COUNTERSUNK HEAD BSP Part No. Thread Length -8052 2" -80522 2-8052 " 2 8" -80524 " -80525 " DECK DRAINS Flush countersunk head. Made in Marelon & 2". Fitted with integral grate, (*not hose model). Colour: off white Part No. Hose Thread Length -8054 * -8055-8056 2" 8" SECTION 5
KM Plastic Skin Fittings Aquafax KM FITTINGS The KM fittings below are moulded in off white Nylon, a strong, stable material unaffected by extreme temperature. These fittings represent high quality at a very competitive price. SKIN FITTINGS Straight type for either. Part No. Thread ID Hose -85000 BSP 8" or -8500 " BSP or " -85002 BSP or SKIN FITTINGS Long, one size hose tail design. Reduces fitting time & errors encountered with dual hose type. Enables two clip fitting. Part No. Thread Hose -8550 BSP -8550 " BSP -85550 " BSP " -85560 " BSP 8" -85590 BSP SKIN FITTINGS BSP Threaded type. Part No. Thread Length (exc nut) -850 5mm -850 " 54mm -8505 55mm SKIN FITTINGS 90 ELBOWS FOR HOSE 90 Part No. Thread Hose -85050 BSP 8" / -8505 BSP -85060 " BSP / " -85062 " BSP -8506 " BSP " -85070 BSP / -85075 BSP ELBOWS BSP female / female Part No. Thread -8504 BSP -8504 " BSP -85045 BSP Part No. Hose -8570 8" / -857-8580 / " -8582-858 " -8590 / -8595 COCKPIT DRAIN Countersunk c/w grating, for flush fitting up to 40mm deck. ID hose. O. dia. 68mm. Part No. -8505 BULKHEAD FITTINGS Supplied as threaded pipe with fixed flange & adjustable back nut. Part No. Thread Length -8508 BSP Male 70mm -8508 " BSP Male 70mm -85085 BSP Male 7mm CONNECTORS Female reducing connector Length 7 8" (22mm) Part No. Thread -8509 BSP -8509 " BSP -85095 BSP -85098 - " BSP 6 SECTION
Aquafax KM Plastic Skin Fittings -85955-85752 -8592 FUELOCK PLASTIC LOCKABLE DIESEL FILLER CAP With increasing costs of fuel, theft from fuel tanks has increase and more boat owners are looking to make fuel tanks secure. KM FITTINGS DIVERTER VALVE Two way valve for liquids and semi solids. May be used with hand or power operated pump, and ideal for bilges or toilet uses. Moulded in PVC bore full (8mm) bore. Supplied either complete with hose connectors fitted (cheaper) or with hose connectors separate to suit application. Description Connectors Part No. Diverter valve only threaded BSP Male -85750 Diverter valve complete with hose connections for ID Hose -85752 Diverter valve complete with hose connections for " ID Hose -8575 Diverter valve complete with hose connections for ID Hose -85754 Diverter valve complete with hose connections for ID Hose -85755 DECK FILLERS Moulded in nylon and resistant to diesel Cap is slotted for plastic key supplied Cap secured by c/p brass ball chain Bodies and caps available in different colours for fuel or water. O.A. dia. 95mm. Spares Part No Spare Key -85940 White Filler Cap (Water) -8594 Blue Filler Cap (Water) -85942 Red Filler Cap (Diesel) -8594 White Filler Cap (Diesel) -85944 PUMP OUT FITTING Designed for closed toilet systems and the nozzle from shore pump out stations. Moulded in black nylon and c/w key. Cap is fitted with 5 8" hex, socket for opening with special key supplied. O.A. Dia: (95mm) Deck aperture: 54mm For Hose Part No. -85955 Spare Key Part No. -85959 Spare cap black Part No. -85957 PLASTIC BACKNUTS Hex. shouldered flange Thread Part No. BSP -8597 " BSP -8597 BSP -85975 Available in BSP and BSP Supplied with multi fixing adaptor flange Size Type Part No. fitting a wide range of existing deck fillers & two keys BSP PETROL 2-7669 Self-closing lock cover keeping the BSP DIESEL 2-76695 elements out of the locking mechanism BSP DIESEL 2-76696 Marked DIESEL or PETROL ( only) on filler cap for BSS and RCD suitable to fit 2-76720/25/70/7 and 86 deck fillers* *Shown in Section 2 Size: Dia. approx 4 (20mm) Projection: 4 5 8" (7mm) Outlets: BSP male Three hole fixing All spares available Body Cap Legend Hose Part No. White White Diesel -8590 White Red Diesel -8592 White White Diesel 2" -85920 White Red Diesel 2" -85922 White White Water -859 White Blue Water -859 White White Water 2" -8592 White Blue Water 2" -8592 HOSE CONNECTORS BSP Male or female thread. Available as single or dual hose types, or join them to make connectors for different size hoses. -8520-85270 Thread Hose Part No. BSP (Male) 8" / Hose -8520 BSP (Male) Hose -852 " BSP (Male) / " Hose -8520 " BSP (Male) Hose -8522 " BSP (Male) " Hose -852 BSP (Male) / Hose -85250 BSP (Male) Hose -85255 Thread Hose Part No. BSP (Female) / " Hose -85270 BSP (Female) / Hose -85280 BSP (Female) Hose -8502 BSP (Female) " Hose -850 BSP (Female) Hose -8505-85270 & -85255 as a hose joiner SECTION 7
Plastic Fittings and Hose Connectors Aquafax P.V.C. BALL CHECK VALVE EPDM Seals SIngle union Threaded BSP parallel Not suitable for diesel Part No. BSP Hose Mat -86200 8" 8" GRPP -8620 GRPP -8628 GRPP -86220 GRPP -8620 " " GRPP -86240 GRPP -86246 " GRPP SAFI PLASTIC FITTINGS Part No. BSP Length O.Dia. -8602 9mm 48mm -86022 05mm 60mm -8602 " 7mm 70mm HOSE CONNECTORS Male BSP Parallel thread. SAFI UPVC & GRPP BALL VALVES AVAILABLE TO ORDER Part No. BSP Hose Mat -86248 GRPP -86250 GRPP -86257 2" GRPP -86258 2" GRPP -86260 2" 2" GRPP -86280 " " GRPP HOSE CONNECTORS SAFI BULKHEAD FITTINGS Heavy duty fittings moulded in black glass reinforced polypropylene. Threaded BSP complete with E.P. gasket & large black nut. Part No. BSP Length O.A. -86 85mm * -862 85mm -86 " 05mm -864 05mm -865 05mm -866 2" 05mm *TO ORDER ONLY The fittings below have barbed ends for hose. Sizes up to are moulded in polypropylene and the larger ones in nylon. ELBOWS Equal ends Hose Part No. 8" 9-69070 9-6907 9-69072 " 9-6907 9-69074 9-69075 2" 9-69076 STRAIGHT CONNECTORS Hose Part No. 8" 9-69080 9-6908 9-69082 " 9-6908 9-69084 9-69085 2" 9-69086 - 8" 9-69087 TEE Equal ends Y CONNECTOR Hose Part No. Hose Part No. 8" 9-69090 8" Y Conn. 9-69220 9-6909 Y Conn. 9-6922 9-69092 Y Conn. 9-69222 " 9-6909 9-69094 9-69095 2" 9-69096 90º PLASTIC SWEPT BEND Designed for domestic systems Inexpensive smooth bore fittings Non-barbed Hose Part No. Hose 9-9694 Hose* 9-9695 * Ideal for toilets and sanitation hose NPT HOSE CONNECTORS PLASTIC UNEQUAL HOSE CONNECTOR ( - 8mm Hose) The connector is stepped and can be cut to join many hose sizes. Hose increments are: mm, 6mm, 9mm, 22mm, 25mm, 28mm, 2mm and 8mm. Part No. 9-96979 Thread Hose Part No. NPT(M) -950 NPT(M) -9502 NPT(M) -9502 NPT(M) -95022 NPT(M) " -9502 " NPT(M) -9502 " NPT(M) " -950 NPT(M) " -9505 NPT(M) -95054 NPT(M) -95055 2" NPT(M) -95065 2" NPT(M) 2" -95066 UPVC COMPACT BALL VALVES Strong, with slim, simple design Open/close by 90 handle rotation P.T.F.E. seats and EPDM seals BSP parallel sockets Nominal pressure 0 bar at 20 C AVAILABLE TO ORDER Part No. BSP A B D H L -86000 8" 42 6 9 8 58-8600 74 20 5 5 76-86002 74 25 20 56 94-8600 " 98 2 25 6 0-86004 98 40 25 6 20-86005 8 50 2 68 4-86006 2" 8 6 4 77 6 Other Safi UPVC & GRPP ball valves are available to order. Full range and technical details available on request. 8 SECTION For more information on these and other products see our website: www.aquafax.co.uk