HAND PROTECTION APPLICATION When engineering and administrative control measures are unable to reduce the exposure to potential hand injuries, employees should be supplied with, and wear, hand protection suitable for the work being performed. or possibility. EN374-3 tests gloves for permeation resistance to chemicals with each combination of chemical / glove classified according to resistance time. Under the standard AS/NZS2161.10 (EN374-3), the symbol describes a permeation performance level equal to or greater than 30 minutes for a group of 12 industrial chemicals in the table below. For many workplace chemical hazards, a range of glove types may be required, one for each task. One type of glove often cannot provide protection against chemical cocktails. If the chemical is a cocktail, assess the glove s performance on the most aggressive chemical. A B C RISK ASSESSMENT The need for hand protection should be assessed by conducting an assessment of potential workplace hazards. There are four interconnected factors to consider when selecting the best form of hand protection for the intended work - the type of hazard (physical, mechanical, chemical, biological); the nature of the task (regular process or incidental / accidental); user comfort (fit, dexterity); and workplace conditions (surface/ambient temperatures, wet/dry). Hand protection must meet the protection parameters detailed in MSDS, safe work method statements or job safety assessments. The most common performance indicators for hand protection are as follows: EN388 applies to gloves that protect against physical and mechanical hazards. It specifies requirements for resistance to damage from abrasion, perforation, tearing and cutting. 4101 ABRASION CUT TEAR PUNCTURE 1-4 1-5 1-4 1-4 The higher the number, the better the performance A METHANOL G DIETHYDROFURANE B ACETONE H TETRAHYDROFURANE C ACETONITRILE I ETHYL ACETATE D DICHLOROMETHANE J N-HEPTANE E CARBON DISULPHIDE K SODIUM HYDROXIDE F TOLUENE L SULPHURIC ACID 96% Glove compatibility charts will help with permeation, degradation and breakthrough times and flow rates. Chemical gloves should be checked routinely for leaks and rejected gloves destroyed immediately. SAFETY TIPS 1. Use solvent and water resistant hand creams before & after work. 2. Some people may develop an allergic reaction to latex gloves. 3. Don t use gloves worn by others. 4. Use a cotton inner glove as a moisture barrier for prolonged glove use. All workers should be trained in the correct use and maintenance of personal protective equipment. EN374 specifies the requirements of gloves for protection against chemicals and/or micro-organisms. EN374-2 has a pass / fail test for gloves to ensure they are sealed against penetration of liquids important for situations where glove immersion is a requirement USEFUL REFERENCES AS/NZS 2161 Set:2008 Occupational protective gloves set. LEATHER & COATED GLOVES DISPOSABLE GLOVES SPECIALTY GLOVES 60 64 65 DISCLAIMER: The information detailed above is not provided as a solution to the control of workplace hazards. It is an outline and has not been prepared as any statement of law nor is it intended to replace or substitute for professional and/or legal advice which is strongly recommended. 59
Zorb-IT General Purpose Gloves - Zorb-IT Black Lite sponge black nitrile flat dipped palm, sanitised breathable nylon liner - for maintenance / assembly applications - Zorb-IT sponge grey nitrile flat dipped palm, sanitised breathable nylon liner - for maintenance / assembly applications - Zorb-IT HV sponge grey nitrile flat dipped palm, sanitised breathable nylon liner - for maintenance / assembly applications GRN4540 UOM GRN4540 ZORB-IT SPONGE NITRILE/NYLON GLOVE 7-10 PR GRN4550 ZORB-IT SPONGE NITRILE ON WHITE GLOVE 6-10 PR GRN4570 ZORB-IT HI VIS SPONGE NITRILE GLOVE 6-10 PR GRN4550 High Performance Cut Resistant Gloves GRN4570 - Zorb-IT Ultimate sponge nitrile dipped, cut resistant Kevlar -Lycra liner, sanitised. Glass / sheet steel hazards / assembly, etc. - Zorb-IT Ultra extended sponge nitrile dip on extended cuff, Kevlar cut resistant liner. Glass / sheet steel hazards / assembly, etc - Showa Kevlar GCR4560 Grip natural rubber coating on Kevlar cut resistant liner. Suitable for glass, steel and aluminium handling. GCR4565 GCRGPKV1 UOM GCR4560 ZORB-IT ULTIMATE NITRILE/KEVLAR -LYCRA GLOVE 6-11 PR GCR4565 ZORB-IT ULTIRA NITRILE/KEVLAR GLOVE 7-11 PR GCRGPKV1 SHOWA KEVLAR GRIP LATEX/KEVLAR GLOVE S - XL PR High Performance Disposable Nitrile Gloves (0.10mm thickness, 240mm length, rolled cuff, powder free) - Nitri-Care 100% blue nitrile, class 1 medical device. For food preparation / medical & maintenance applications - N-DEX Free 100% accelerator-free green nitrile, class 1 medical device. For medical / dental & beauty care applications - Nighthawk 100% accelerator-free black nitrile. For police / hairdressing & military applications GDN3005 GDN7705 GDN7700 UOM GDN3005 NITRI-CARE NITRILE BLUE GLOVE XS - XL BX/100 GDN7705 N-DEX FREE NITRILE GREEN GLOVE XS - XL BX/100 GDN7700 NIGHTHAWK NITRILE BLACK GLOVE S - XL BX/50 60 www.safetyquip.com.au
ATLAS Premium Rubber Gloves - Showa Hi-Vis yellow liner with orange natural rubber palm coat. Suitable for construction, parks & gardens, maintenance, building work, transport & warehousing. - Showa Grip black natural rubber coating on grey poly cotton liner. Suitable for construction, parks & gardens, maintenance, building work, transport & warehousing. - Showa Re-Grip reinforced black natural rubber coating on poly cotton liner. Suitable for construction, parks & gardens, maintenance, building work, transport & warehousing. GRL317 GRL310B GRL330 UOM GRL317 SHOWA HI-VIS GRIP GLOVE S - XL PR GRL310B SHOWA GRIP BLACK COATING ON GREY LINER S - XL PR GRL330 SHOWA RE-GRIP REINFORCED THUMB CROTCH S - XL PR High Performance Polyurethane Coated Gloves - Showa Palm Fit polyurethane coating on nylon liner. Excellent for where ultimate dexterity is required, without cut protection. - Showa Palm Plus cut resistant 13 gauge HPPE polyethylene fiber, grey polyurethane palm coating. Steel / aluminium / glass hazards, etc. GNY500B GCR541 UOM GNY500B SHOWA PALM FIT POLYURETHANE COATED NYLON S - 2XL PR GCR541 SHOWA PALM PLUS POLYURETHANE COATED HPPE POLYETHYLENE S - 2XL PR Premium Chemical Protection Gloves - Ultraflex neoprene coated cotton interlock liner, sanitised, 355mm gauntlet. Petrochemical, acids, oils & fats - Nitri Solve 100% nitrile, unlined, green, 0.56mm thick, 480mm length, non slip grip. NFPA compliant - Nitri Solve 100% nitrile, flock-lined, green, 0.38mm thick, 330mm length, non slip grip GRN3414 GRN747 GRN730 UOM GRN3414 ULTRAFLEX II NEOPRENE BLACK GAUNTLET GLOVE 8-11 PR GRN747 NITRI SOLVE NITRILE FLOCK-LINED GREEN, 0.56MM GLOVE 7-11 PR GRN730 NITRI SOLVE NITRILE FLOCK-LINED GREEN, 0.38MM GLOVE 6-11 PR 61
Leather Rigger s Gloves - Cow or pig leather options to suit application - Wing thumb pattern with stitch free palm - Elasticised back for secure fit GLC201 BOSS COW HIDE LEATHER RIGGER S - 2XL GLC050 SPLIT CHROME COW HIDE LEATHER RIGGER L - 2XL GLC301 STANDARD COW HIDE LEATHER RIGGER S - XL GLP012 PREMIUM PIG HIDE LEATHER RIGGER S - XL Leather General Purpose Gloves - Standard or reinforced palms for extra durability - Heavy duty split cow leather palms - Wrist length with safety cuff for added wrist protection GLC201 GLC050 GLC747 GLC301 GLP012 GLC722 CODE DESCRIPTION SIZE GLC727 PREMIUM COW LEATHER PALM/COTTON BACK L GLC747 ECONOMY COW LEATHER PALM/COTTON BACK L GLC722 HEAVY DUTY ALL COW LEATHER L GLC714 COW LEATHER REINFORCED PALM/COTTON BACK L GLC727 GLC714 GLC717 GLC717 COW LEATHER REINFORCED PALM/COTTON BACK L Leather Welder s Gloves - Standard or reinforced palms & thumbs for extra durability - Kevlar stitched options for added durability - Lined and welted GLC50W GLC60W GLC55W CODE DESCRIPTION SIZE GLC50W BLACK/GOLD STANDARD WELDERS 406MM L GLC60W BLUE/GOLD REINFORCED WELDERS 406MM L GLC55W GREEN/GOLD LEFT HAND ONLY REINFORCED WELDERS 406MM L GLC57W RED HOT SHOT REINFORCED WELDERS 406MM L GLC57W GLP16W GLP16W TIG PIG LEATHER WELDERS 300MM L Cotton General Purpose Gloves - Knitted, interlock and drill styles for a wide range of tasks - PVC & latex palm treatments for added functionality - Ladies sizing available in some styles GCO450 GCO440 CODE DESCRIPTION SIZE GCO418 PVC DOT KNITTED POLY/COTTON M GCO450 KNITTED POLY/COTTON M GCO440 INTERLOCK COTTON M GCO418 GCO094 PVC LATTICE KNITTED POLY/COTTON M GCO410 KNIT WRIST DRILL COTTON M GCO094 GCO410 62 www.safetyquip.com.au
PVC Dipped Gloves - PVC dipped on cotton interlock liner - Resistant to oil, grease & dilute chemicals - Single or double dipped options CODE DESCRIPTION SIZE GPV127 27CM RED SINGLE DIP PVC M GPV126 27CM RED SINGLE DIP PVC KNIT WRIST M GPV145 45CM RED SINGLE DIP PVC M GPV227 27CM GREEN DOUBLE DIP PVC M GPV245 45CM GREEN DOUBLE DIP PVC M Latex Dipped Gloves - Specialised latex palm dip coatings for grip, chemical, cut and wear resistance - Variety of liners for added comfort and protection GPV127 GPV126 GPV227 GRL5440 GPV145 GPV245 GRL5476 GRL5485 GREEN LATEX COATED POLY/COTTON KNIT 8-11 GRL5440 RED COARSE LATEX COATED POLY/COTTON KNIT L GRL5476 YELLOW RIPPLE LATEX COATED POLY/COTTON KNIT L GCR1000 BLUE LATEX COATED KEVLAR KNIT (7 G) 8-11 GRL5000 BLACK LATEX COATED STRETCH NYLON KNIT 8-11 GRL5485 GCR1000 GRL5000 Nitrile Dipped Gloves - Full and palm dip nitrile coatings for abrasion, chemical and grip applications - Weight and formulation options to suit specific work environments GRN5635 GRN5630 GRN5643 GREY NITRILE FOAM COATED NYLON KNIT 7-10 GRN5635 BLUE H/W NITRILE COATED COTTON KNIT WRIST (FULL DIP) 8-10 GRN5630 BLUE H/W NITRILE COATED COTTON SAFETY CUFF (FULL DIP) 9-10 GRN5460 YELLOW L/W NITRILE COATED COTTON KNIT WRIST 7-10 GCR2000 BLACK NITRILE COATED KEVLAR KNIT 8-10 GRN5643 GRN5460 GCR2000 General Purpose Chemical Gloves Polyurethane Dipped Gloves - Nitrile gloves for chemical and abrasion protection - Check chemical resistance guides to assist in selecting the most appropriate glove for the intended application GRN5650 GRN5655 GRN5650 GREEN NITRILE FLOCK LINED 33CM S - 3XL GRN5655 GREEN NITRILE UNLINED 45CM M - XL DynaPro Cut Resistant Glove - ProNeema liner and PU coating provide excellent abrasion, tear & cut resistance - EN388 (4343) ProLite Grey - Polyurethane (PU) coated palm with nylon liner - EN388 (4131) GCRPUD GCRPUD DYNAPRO PU COATED DYNEEMA 8-11 GNY1010 PROLITE PU COATED NYLON 7-11 GNY1010 63
General Purpose Latex Industrial Gloves - Process Blues silverlined, made from FDA compliant materials, pebble grip, anti-microbial protection, silicone free - Tuff Pinks premium silverlined, excellent tensile strength, tear resistant, pebble grip, anti-microbial protection, silicone free - Thrifty Yellows economy flocklined, embossed pattern palm, beaded cuff to add strength GRL300 PROCESS BLUES SILVERLINED 7-11, 7½ - 9½ GRL330 TUFF PINKS SILVERLINED 7-11, 7½ - 9½ GRL350 THRIFTY YELLOWS FLOCKLINED S - 2XL Disposable Single Use Gloves - Non-Sterile - Vinyl, latex free, made from FDA compliant materials, ambidextrous design, HACCP Australia food safety certification - Nitrile examination, latex free, meets Australian Standard AS/NZS 4011:1997/Amdt 1. 1998, TGA listed, ambidextrous design, beaded cuff - Latex examination, medical grade, meets Australian Standard AS/NZS 4011:1997/Amdt 1. 1998, ambidextrous design, beaded cuff, in accordance with EN455 pts 1, 2 & 3 GRL300 GRL330 GRL350 CODE DESCRIPTION COLOUR SIZES GDV5500 VINYL LIGHTLY POWDERED (BX/100) CLEAR, BLUE S - XL GDV5510 VINYL POWDER FREE (BX/100) CLEAR S - XL GDN7500 NITRILE POWDER FREE (BX/100) BLUE S - XL GDL6500 LATEX LIGHTLY POWDERED (BX/100) NATURAL XS - XL GDL6510 LATEX POWDER FREE (BX/100) NATURAL XS - XL GDV5500 GDN7500 GDL6500 Disposable Single Use Gloves - Non-Sterile - Vinyl, latex free, HACCP food safety accreditation, ambidextrous design - Nitrile examination, HACCP food safety accreditation, AQL 1.5, TGA listed, ambidextrous design, textured fingertips - Latex examination, medical grade, HACCP food safety accreditation, AQL 1.5, ambidextrous design CODE DESCRIPTION COLOUR SIZES GDV5525 VINYL LIGHTLY POWDERED (BX/100) CLEAR, BLUE S - XL GDV5520 VINYL POWDER FREE (BX/100) CLEAR S - XL GDN7550 NITRILE POWDER FREE (BX/100) BLUE S - XL GDL6550 LATEX LIGHTLY POWDERED (BX/100) NATURAL S - XL GDL6560 LATEX POWDER FREE (BX/100) NATURAL S - XL GDV5525 GDN7550 GDL6550 Tri Tuff Triple Blend Examination Glove - Innovative triple blend of latex, nitrile & neoprene - powder free - Single use, non-sterile ambidextrous, pebbled finger ends - Nitrile / neoprene content assists in providing some resistance to oils & chemical splash - Meets Australian Standard AS/NZS 4011:1997/Amdt 1. 1998 - Resistant to a broader range of chemicals than any other glove - Can be used as a disposable glove without need for cleaning/recycling - Ambidextrous design, ideal as a single use glove - Suitable for use as a secondary inner glove Silver Shield Hazardous Chemical Gloves 64 GDL41012 TRI TUFF DISPOSABLE GLOVE (BX/100) S - XL GSC104 NORTH SILVER SHIELD FOIL GLOVE 6, 7, 8, 9, 10 www.safetyquip.com.au
- Ideal for use in many electrical applications from low voltage to high voltage - Meets all protection classes from 00 to 4 - Available in multiple sizes - use with leather overgloves for increased mechanical protection - Reversible steel mesh gloves & armguards - Detachable wrist straps for increased user comfort - Colour coded size range - Extended cuff & armguard options available Electrosoft Latex Electricians Glove CODE CLASS VOLTAGE LENGTH SIZES GRL091903 00 500V 360mm 7-11 GRL091907 0 1000V 360mm 8-11 GRL091912 1 7500V 360mm 9-11 GRL091921 2 17000V 360mm 9-11 GRL091931 3 26500V 360mm 9-11 GRL091941 4 36000V 410mm 10-11 CHAINEXTRA Stainless Steel Gloves - PVC foam coating for water repellency, comfort & enhanced grip in wet and dry conditions - Bare Hand Feel technology for increased dexterity & control - Seamless 15 gauge shell for a thicker, stronger & tighter knit - 100% apparel grade nylon - latex free - CE rating 4131 DexiPro Nitrile Foam Coated Glove - Lint free nylon machine knit with LYCRA - Nitrile coating provides superior gripping power - Bare hand feel technology provides increased dexterity and control Stinga PVC Foam Coated Glove GPVNPF GRNBNNL GCR54200S CHAINEXTRA 5 DIGIT GLOVE, WRIST LENGTH XS-2XL GPVNPF STINGA PVC FOAM COATED NYLON 7-11 GRNBNNL DEXIPRO NITRILE COATED NYLON 7-11 Cut, Puncture & Abrasion Resistant Hand Protection - Search offers the highest levels of needle protection whilst maintaining dexterity - Duty provides 4 times the needle resistance of ordinary leather gloves, palm lined with new TurtleSkin fabric - Safe Handler provides protection from puncture and cut with excellent durability and grip. Aramid knit outer with aramid blend layer inside. Note: These gloves are not cut or puncture proof GGMTCC002 TURTLESKIN SEARCH GLOVE (PR) XS -XXL GGMTCC006 TURTLESKIN DUTY GLOVE (PR) XS -XXL GCRAPD2D1 TURTLESKIN SAFE HANDLER GLOVE (PR) L GGMTCC002 GGMTCC006 GCRAPD2D1 Grip N Hot Mill Glove Gloveguard - Provide protection against intermittent heat up to 200ºC - Nitrile palm coating provides excellent grip and longer life - Knit design allows hands to breathe - Double jaw configuration - Attaches to belt loop, pocket, etc - Safety Breakaway feature - Metal detectable version available GTH7146 GRIP N HOT MILL GLOVE MENS CODE DESCRIPTION UOM MGG1 GLOVEGUARD EA 65
Synthetic Leather Hand Protection - Non-slip grip - more gripping power - Neoprene knuckle panel provides increased flexibility - Velcro wrist straps for extra protection and wrist support - One piece synthetic leather palm - Easy-on finger loop - Ideal for use with hand & power tools ProVibe - Anti-vibration foam padded palm ProFit Magna Tech - Magnet incorporated on back of hand for securing nails & screws ProFit - Fingerless with Geko Grip palm ProTek - Reinforced foam padded inner palm GAVPV GLSPFM GLSPF ProFit Extreme - Geko Grip palm with heavy duty safety Hook N Loop wrist strap provides extra protection and wrist support GAVPV PROVIBE ANTIVIBRATION M, L, XL GLSPFM PROFIT MAGNATECH M, L, XL GLSPF PROFIT FINGERLESS M, L, XL GLSPT PROTEK FOAM PADDED M, L, XL GLSPFE PROFIT EXTREME HEAVY DUTY M, L, XL GLSPT GLSPFE Synthetic Leather Hand Protection - Reinforced wear areas, knuckle & palm protection - Washable long lasting fabrics Warrior - Heavy duty, fully lined, velcro strap closure Coverguard - Light duty, spandex back, elastic cuff GLS22 GLS24 Gripguard - Extra grip, PVC full silicone grip patterntern Mechano Half - Reinforced palm, exposed finger tips GLS21 Mechano - Full finger, reinforced palm, padded knuckles Shockguard Gel - Vibration protection, impact GEL pads, full finger GLS34 GLS33 Shockguard Gel Half - Vibration protection, impact GEL pads, exposed finger tips GLS21 WARRIOR BLUE/BLACK GLOVE S - 2XL GLS22 COVERGUARD GREEN/GREY GLOVE S - 2XL GLS24 GRIPGUARD RED/GREY/BLACK GLOVE S - 2XL GLS34 MECHANO HALF BLACK FINGERLESS GLOVE S - 2XL GLS33 MECHANO BLACK GLOVE S - 2XL GAV14 SHOCKGUARD GEL BLACK/GREY GLOVE S - 2XL GAV12 SHOCKGUARD GEL HALF FINGERLESS BLACK/GREY GLOVE S - 2XL GAV14 GAV12 66 www.safetyquip.com.au