M E R I D I A N apexfacades.com 1.866.970.5948 apexfacades.com 4 5 0 T 1.0 H E R M A L L Y B R O K Meridian E N Pg- 1 S T O R E F R O N T
THIS PAGE INTENTIONALY LEFT BLANK apexfacades.com 1.0 Meridian Pg- 2
Storefront FEATURES Thermal strutting for exceptional thermal performance and strength Sill tray and head deflector for easy installation Screw spline and shear block fabrication Multi configuration corner solutions Flush Glazed or Center Glazed Options Infill options from ¼ (6mm) to 1 (25mm) thicknesses Tested to current industry standard and codes OPTIONAL FEATURES Integrated entrance framing systems Compatible with Crest and Summit Doors Compatible with vents FINISHES TECHNICAL SERVICES Available in 7 standard anodized finishes Painted finishes in standard and custom colours Split finishes available Structural Performance Charts Thermal Performance Charts Design assistance and support apexfacades.com 1.0 Meridian Pg- 3
ARCHITECTURAL DETAILS apexfacades.com 1.0 Meridian Pg- 4
Shear Block Transom-Mullion Connection 6,3 [1/4"] 28,6 [1 1/8"] H1 131,8 [5 3/16"] DEFLECTOR 450190-A H1 BITE, TYP. C.L. SHEAR BLOCK 450110-A H1 (2) #10x1/2" SS (18-8) PH ST SCREWS, 200310 SHEAR BLOCK 450180-A DEFLECTOR SET IN SEALANT (2) #10x1 1/2" (18-8) PH ST SCREWS, 450290 450050 END DAM PLATE 450210 SILL TRACK 450090 apexfacades.com 1.0 Meridian Pg- 5
Mullion Machining for Transom, Shear Block Connection EQ. EQ. 48 [1 7/8"] V2 H2 V2 V2 V2 450120 9,2 26 [1 1/32"] BITE, TYP. 12,4 ANTI-WALK W-SHAPE SHIM 450110 REINFORCING IF REQUIRED 12,7 450050 7,7 [5/16"] 19,1 [3/4"] 25,4 [1"] (2) 200310 (2) 450190-A 28,6 [1 1/8"] 3,2 [1/8"] GAP H2 12,7 BITE, TYP. SHEAR BLOCK 450110-A DEFLECTOR SET IN SEALANT (2) 200310 450050 450180-A apexfacades.com 1.0 Meridian Pg- 6
Top & Bottom Transom-Mullion Assembly 450200-A 142 [5 19/32"] 450100 (2) 450280 450130 BITE, TYP. 15,9 [5/8"] 57,2 [2 1/4"] 450110-A 23,8 [15/16"] 450240 V6 TOP TRANSOM, MOUNTING RECEPTOR V4 TOP TRANSOM, HEAD RECEPTOR BITE, BITE, TYP. TYP. 26,7 9,2 [1 1/16"] 26,7 9,2 7,7 [1 1/16"] [5/16"] 7,7 450050 450120 [5/16"] 450240 BITE, BITE, TYP. TYP. ÿ8 [5/16"] 57,2 [2 1/4"] 25,4 [1"] ÿ8 [5/16"] 57,2 [2 1/4"] 25,4 [1"] 131,8 [5 3/16"] 131,8 [5 3/16"] V5 V5 BOTTOM TRANSOM V3 V3 BOTTOM TRANSOM, SILL TRACK apexfacades.com 1.0 Meridian Pg- 7
90º Corner Post 27,5 [1 3/32"] 30 [1 3/16"] 19,1 [3/4"] 7,7 [5/16"] INTERIOR 90 19,1 [3/4"] EQ. EQ. 48 [1 7/8"] 9,2 450060 450070 7,7 [5/16"] H3 90 CORNER POST EXTERIOR 450190-A 450070 450060 450190-A 450180-A (2) 200310 450110-A 450050 450050 450090 apexfacades.com 1.0 Meridian Pg- 8
-90º Corner Post & Wide 4.5" x 4.5" Post 450070 450060 7,7 [5/16"] 26,7 [1 1/16"] 9,2 INTERIOR EXTERIOR 9,2 H4-90º CORNER POST 26,7 [1 1/16"] 450060 INTERIOR 19,1 [3/4"] EQ. EQ. 48 [1 7/8"] 9,2 450070 7,7 [5/16"] H5 4 1/2"x4 1/2" POST EXTERIOR apexfacades.com 1.0 Meridian Pg- 9
Door Jambs, Summit 200 Out-Swing Door 450245 200165 450020 15,9 [5/8"] 200170 31,8 [1 1/4"] 25,4 [1"] H6 TYPICAL MULLION BITE, TYP. 12,7 ELECTRIC STRIKE H7 DOOR JAMB 3,2 [1/8"] DOOR OPENING 15,4 [19/32"] 450020 450245 ANTI-WALK W-SHAPE SHIM 31,5 [1 1/4"] 3,2 [1/8"] 25,4 [1"] DOOR OPENING H8 DOOR JAMB H9 12,7 TYPICAL MULLION BITE, TYP. apexfacades.com 1.0 Meridian Pg- 10
Door Jambs, In-Swing Door 450020 28,6 [1 1/8"] 31,5 [1 1/4"] 200170 H10 TYPICAL MULLION BITE, TYP. 12,7 H11 DOOR JAMB 15,9 [5/8"] DOOR OPENING 450020 ANTI-WALK W-SHAPE SHIM 450245 28,6 [1 1/8"] 31,8 [1 1/4"] 15,9 [5/8"] DOOR OPENING H12 DOOR JAMB H13 12,7 TYPICAL MULLION BITE, TYP. apexfacades.com 1.0 Meridian Pg- 11
Door Header Summit 200 Out-Swing & In-Swing Doors (2) 450280 450110-A 450180-A 27,4 [1 1/16"] 27,4 [1 1/16"] 450020 OFFSET PIVOT 3,2 [1/8"] 3,2 [1/8"] 31,8 [1 1/4"] 25,4 [1"] 200170 200165 28,6 [1 1/8"] 31,8 [1 1/4"] V7 OUTSWING DOOR SECTION V8 INSWING DOOR SECTION apexfacades.com 1.0 Meridian Pg- 12
Top Lite 450020 25,4 [1"] BITE, TYP. 12,7 450155 H14 TYPICAL MULLION H15 DOOR OPENING DOOR JAMB, ABOVE HEADER 25,4 [1"] 450020 ANTI-WALK W-SHAPE SHIM 450245 450155 DOOR OPENING H16 DOOR JAMB, ABOVE HEADER H17 12,7 TYPICAL MULLION BITE, TYP. apexfacades.com 1.0 Meridian Pg- 13
Top Lite. 4 1/2" x 4 1/2" T-Post 450020 25,4 [1"] ANTI-WALK W-SHAPE SHIM 450245 450155 17,4 [11/16"] 19,1 [3/4"] DOOR OPENING DOOR JAMB BELOW H181 DOOR JAMB, ABOVE HEADER HEADER-TRANSOM 9 H19 H18 44,4 [1 3/4"] 25,4 [1"] H19 12,7 44,4 [1 3/4"] 25,4 [1"] CENTER MULLION, ABOVE HEADER INTERIOR 450060 450080 H20 T-POST EXTERIOR apexfacades.com 1.0 Meridian Pg- 14
Door Jambs, Crest 175 Out-Swing Door 450020 12,5 450140 44,5 [1 3/4"] 3,2 [1/8"] 15,9 [5/8"] 48 [1 29/32"] 43 [1 11/16"] ELECTRIC STRIKE H21 H22 H212 TYPICAL MULLION H22 DOOR JAMB DOOR OPENING 450020 450140 3,2 [1/8"] DOOR OPENING H23 DOOR JAMB, ABOVE HEADER H24 TYPICAL MULLION BITE, TYP. apexfacades.com 1.0 Meridian Pg- 15
Interior Glazing Option, Top Transom Options 450100 450200-A 450130 450050 450120 V9 TOP TRANSOM, MOUNTING BRACKET C.L. 65,1 [2 9/16"] Ø8 [5/16"] 25,4 [1"] 450050 450120 C.L. 450090 131,8 [5 3/16"] V10 SECTION THROUGH INTERNAL GLAZING ASSEMBLY apexfacades.com 1.0 Meridian Pg- 16
1/4 (Outside) Glazing Option 450070 450060 INTERIOR 90 450060 450070 450231 EXTERIOR H26 90º CORNER POST, 1/4" GLAZING OPTION H25 450170-90º CORNER POST, 1/4" GLAZING OPTION 450020 450160 INTERIOR H27 DOOR JAMB, ABOVE HEADER 15,7 [5/8"] 450150 H28 DOOR OPENING EXTERIOR TYPICAL MULLION, 1/4" GLAZING OPTION apexfacades.com 1.0 Meridian Pg- 17
Screw-Spline Transom-Mullion Assembly (2) 450040 DEFLECTOR 450190-A PRE-ASSEMBLED FRAME (SCREW-SPLINE METHOD), 450030 6,3 [1/4"] INTERIOR (3) #10x1 1/2" ZINC-PLATED SELF-TAPPING SCREWS, 450270 (2) 450040 131,8 [5 3/16"] SEALANT EXTERIOR H29 450030 JAMB, SCREW-SPLINE ASSEMBLY BITE, TYP. SILL TRACK WITH ALUMINUM END DAM 5/16" DRAIN HOLE @ MODULE QUARTER MODULE POINTS EXTERIOR INTERIOR DEFLECTOR SET IN SEALANT 25,4 [1"] 25,4 [1"] 450050 450090 450120 Ø8 [5/16"] 4,8 [3/16"] 57,2 [2 1/4"] 65,1 [2 9/16"] 4,8 [3/16"] SEALANT 131,8 [5 3/16"] V11 BOTTOM TRANSOM, SILL TRACK apexfacades.com 1.0 Meridian Pg- 18
Screw-Spline Transom-Mullion Assembly DEFLECTOR 450190-A (2) 450040 450030 #10x1 1/2" ZINC-PLATED SELF-TAPPING SCREW, 450270 450120 450050 H30 C.L. C.L. TYPICAL MULLION, SCREW-SPLINE ASSEMBLY 450120 C.L. C.L. 64,2 [2 17/32"] 25,4 [1"] 4,8 [3/16"] 4,8 [3/16"] (2) 450040 V12 TRANSOM (3) #10x1 1/2" ZINC-PLATED SELF-TAPPING SCREW, 450270 450120 450030 apexfacades.com 1.0 Meridian Pg- 19
Screw-Spline Top Transom-Mullion Assembly 420200-A 142 [5 19/32"] 450100 450130 23,8 [15/16"] BITE, TYP. 15,9 [5/8"] 15,9 [5/8"] 57,2 [2 1/4"] 450030 V13 TOP TRANSOM, MOUNTING BRACKET V14 TOP TRANSOM, HEAD RECEPTOR V14 (4) #10x1 1/2" ZINC-PLATED SELF-TAPPING SCREW, 450270 (2) 450040 450030 apexfacades.com 1.0 Meridian Pg- 20
FABRICATION DETAILS apexfacades.com 1.0 Meridian Pg- 21
Mullion Machining for Transom, Shear Block Connection 450050 C.L. C.L. (4) Ø4 [Ø5/32 ] CLEAR HOLES 7,7 [5/16"] 19,1 [3/4"] 97,5 [3 27/32"] 9,2 13 26 [1 1/32"] REF. INTERMEDIATE MULLION, TYPICAL 19,1 [3/4"] 97,5 [3 27/32"] 9,2 JAMB MULLION, TYPICAL apexfacades.com 1.0 Meridian Pg- 22
Mullion Machining for Header, Shear Block Connection (4) Ø4 [Ø5/32 ] CLEAR HOLES 13 26 [1 1/32"] REF. C.L. 9,2 TYP. 96 [3 25/32"] 9,2 FRAME INTERMEDIATE MULLION, TYPICAL 96 [3 25/32"] 9,2 JAMB MULLION, TYPICAL apexfacades.com 1.0 Meridian Pg- 23
Split Mullion Machining for Transom, Screw-Spline Connection (3) Ø5,6 [Ø7/32 ] CLEAR HOLES 450050 C.L. C.L. 25,4 [1"] REF. 64,2 [2 17/32"] 25,4 [1"] 20,6 [13/16"] 4,8 [3/16"] 41,2 [1 5/8"] REF. SPLIT MULLION, PART A, TYPICAL 450030 25,4 [1"] REF. 64,2 [2 17/32"] 89,6 [3 17/32"] 25,4 [1"] 450040 450040 22,7 [29/32"] REF. SPLIT MULLION, PART B (TWO-PART), TYPICAL 9,6 15,8 [5/8"] 37,3 [1 15/32"] REF. 15,8 [5/8"] 37,3 [1 15/32"] 9,6 apexfacades.com 1.0 Meridian Pg- 24
Split Mullion Machining for Header, Screw-Spline Connection (4) Ø5.6 [Ø7/32 ] CLEAR HOLES 4,8 [3/16"] 41,2 [1 5/8"] REF. C.L. 20,6 [13/16"] 25,4 [1"] REF. 64,2 [2 17/32"] 25,4 [1"] SPLIT MULLION, PART A, TYPICAL 450030 25,4 [1"] REF. 64,2 [2 17/32"] 89,6 [3 17/32"] 25,4 [1"] 450040 450040 22,7 [29/32"] REF. SPLIT MULLION, PART B (TWO-PART), TYPICAL 9,6 15,8 [5/8"] 37,3 [1 15/32"] REF. 15,8 [5/8"] 37,3 [1 15/32"] 9,6 apexfacades.com 1.0 Meridian Pg- 25
Door Jamb Machining for Door Frame Header & Transom Shear Block Connection 450180-A SHEAR BLOCK TO ACCOMMODATE TOP PIVOT 450020 C.L. C.L. 18,1 [23/32"] 8,4 [11/32"] 19,1 [3/4"] 5,1 [3/16"] 79,3 [3 1/8"] 27,4 [1 1/16"] 13 12,4 26 [1 1/32"] REF. 450050 12,4 26 [1 1/32"] 97,5 [3 27/32"] 19,1 [3/4"] C.L. C.L. SHEAR BLOCK 450110-A 79,3 [3 1/8"] 27,4 [1 1/16"] 19,1 [3/4"] 450020 450020 DOOR 97,5 [3 27/32"] 19,1 [3/4"] DOOR 19,1 [3/4"] 97,5 [3 27/32"] 27,4 79,3 [1 1/16"][ 3 1/8"] 19,1 [3/4"] DOOR JAMB-TO-HEADER MACHINING (SIDE 1) DOOR JAMB-TO-TRANSOM MACHINING (SIDE 2) apexfacades.com 1.0 Meridian Pg- 26
Door Jamb Machining for Door Frame Header & Top Transom, Shear Block Connection (4) Ø4 [Ø5/32 ] CLEAR HOLES 12,4 13 26 [1 1/32"] REF. 12,4 13 26 [1 1/32"] REF. 96 [3 25/32"] REF. C.L. (4) Ø4 [Ø5/32 ] CLEAR HOLES 450020 C.L. 27,4 [1 1/16"] 60,3 [2 3/8"] 27,4 [1 1/16"] FRAME DOOR 450020 DOOR JAMB-TO-HEADER & TOP TRANSOM MACHINING apexfacades.com 1.0 Meridian Pg- 27
Door Jamb Machining for Transom, Shear Block Connection 450050 REF. 26 [1 1/32"] 13 78,4 [3 3/32"] 17,5 [11/16"], REF. C.L. C.L. (3) Ø4 [Ø5/32 ] CLEAR HOLES 105,4 [4 5/32"] 105,4 [4 5/32"] 78,4 [3 3/32"] 450070 450060, REF. apexfacades.com 1.0 Meridian Pg- 28
Door Jamb Machining for Header, Shear Block Connection (4) Ø4 [Ø5/32 ] CLEAR HOLES 105,4 [4 5/32"] 105,4 [4 5/32"] 27,4 [1 1/16"] 60,3 [2 3/8"] FRAME 13 26 [1 1/32"] REF. 12,4 C.L. 78,1 [3 1/16"] 17,7 [11/16"] REF. 450070 450060, REF. apexfacades.com 1.0 Meridian Pg- 29
Door Jamb Machining for Top Transom, Shear Block Connector 450050 REF. 26 [1 1/32"] 13 97,5 [3 27/32"] 19,1 [3/4"], REF. C.L. C.L. (4) Ø4 [Ø5/32 ] CLEAR HOLES 450060 97,5 [3 27/32"] 19,1 [3/4"] 450070, REF. 105,4 [4 5/32"] apexfacades.com 1.0 Meridian Pg- 30
Door Jamb Machining for Top Transom, Shear Block Connector (4) Ø4 [Ø5/32 ] CLEAR HOLES FRAME 13 26 [1 1/32"] REF. 12,4 C.L. 96 [3 25/32"] REF. 450060 96 [3 25/32"], REF., REF. 105,4 [4 5/32"] 450070 apexfacades.com 1.0 Meridian Pg- 31
Machining of Transom, Shear Block Connection 450050 (4) Ø5 [Ø3/16 ] CLEAR HOLES 19 [3/4"] 17,5 [11/16"] 19,1 [3/4"] LENGTH 19,1 [3/4"] 17,5 [11/16"] 25,4 [1"] 79,4 [3 1/8"] (4) Ø5 [Ø3/16 ] CSK CLEAR HOLES 17,5 [11/16"] 19,1 [3/4"] LENGTH 19,1 [3/4"] apexfacades.com 1.0 Meridian Pg- 32
Door Jamb Machining for Door Header, Shear Block Connection 450020 17,8 [11/16"] 17,8 [11/16"] 79,4 [3 1/8"] 79,4 [3 1/8"] 19,1 [3/4"] LENGTH 19,1 [3/4"] (4) Ø5 [Ø3/16 ] CSK CLEAR HOLES apexfacades.com 1.0 Meridian Pg- 33
Storefront Thermal Chart NFRC SIMULATION REPORT MERIDIAN 450 STOREFRONT SIMULATION METHOD: ANSI/NFRC 100, Procedure for Determining Fenestration Product U-Factors (2014) ANSI/NFRC 200, Procedure for Determining Fenestration Product Solar Heat Gain Coefficients at Normal Incidence (2014) NFRC 500, Procedure for Determining Fenestration Product Condensation Resistance Values (2014) Technical Interpretation Manual (2010) SIMULATION SIZE: 2000mm x 2000mm (79in in x 79in) apexfacades.com 1.0 Meridian Pg- 34
Windload Charts GENERAL NOTES WINDLOAD CHARTS 1. Deflection Limit: L/175 (Note: to convert to L/240 + ¼ deflection limit, multiply mullion spacings by 0.70. For example, if mullion can be spaced at 4 ft o.c., multiply by 0.7 = 2.80 ft spacing ok at L/240 + ¼ ) 2. Assume horizontal members (if any) provide lateral support for seismic loads 3. Value of mullion includes back section, thermal breaks and nosing 4. Steel reinforcing inertia value expressed in aluminum for total inertia value (i.e. steel value is factored up by ratio of steel / aluminum modulus values) DEADLOAD CHARTS 1. Deflection requirements comply with S157-05/S157.1-05 and AAMA TIR-A11-2015. Deflection Limit - 1/8. 2. Transom freely supported at ends with setting blocks at 1/4 or 1/8 of transom length. 3. Value of transom includes back section, thermal break and nosing. 4. All reinforcing shown in these charts considered that it is mechanically fastened to the aluminum extrusion. Fastening requirements to be reviewed and approved by Engineer. *Charts are based on deflection analysis only and considered for estimation purposes only. Designer has to take necessary steps to make appropriate engineering calculations as per applicable Building Codes and regulations for compelte design, i.e. stress, slenderness, local buckling. WINDLOAD SPAN CHART 1 *DRAWING TITLE: MULLION SECTION WINDLOAD CHART 1 PROFILE QUALITIES MULLION: lxx = 2.9990 in4 ALUMINUM ALLOY: lxx = in4 SECTION NUMBER: 6063-T6 MATERIAL PROPERTIES ALUMINUM MODULES: E = 10,100,000 psi STEEL MODULES: E = 29,000,000 psi 6063-T6 YIELD STRENGTH: Fy = 21,000 psi apexfacades.com 1.0 Meridian Pg- 35
Windload Charts WINDLOAD SPAN CHART 2 *DRAWING TITLE: WITH (2) 450110 MULLION SECTION WINDLOAD CHART 2 (2) PROFILE QUALITIES MULLION: lxx + 5.480 in4 ALUMINUM ALLOY: lxx = in4 SECTION NUMBER: 6063-T6 MATERIAL PROPERTIES ALUMINUM MODULES: E = 10,100,000 psi STEEL MODULES: E = 29,000,000 psi 6063-T6 YIELD STRENGTH: Fy = 21,000 psi WINDLOAD SPAN CHART 3 *DRAWING TITLE: 450020 MULLION SECTION WINDLOAD CHART 3 450020 PROFILE QUALITIES MULLION: lxx = 3.564 in4 ALUMINUM ALLOY: lxx = in4 SECTION NUMBER: 6063-T6 MATERIAL PROPERTIES ALUMINUM MODULES: E = 10,100,000 psi STEEL MODULES: E = 29,000,000 psi 6063-T6 YIELD STRENGTH: Fy = 21,000 psi apexfacades.com 1.0 Meridian Pg- 36
Windload Charts WINDLOAD SPAN CHART 4 *DRAWING TITLE: 450020 WITH 2-450110 MULLION SECTION WINDLOAD CHART 4 450020 with (2) 450110 PROFILE QUALITIES MULLION: lxx = 3.912 in4 ALUMINUM ALLOY: lxx = in4 SECTION NUMBER: 6063-T6 MATERIAL PROPERTIES ALUMINUM MODULES: E = 10,100,000 psi STEEL MODULES: E = 29,000,000 psi 6063-T6 YIELD STRENGTH: Fy = 21,000 psi WINDLOAD SPAN CHART 5 *DRAWING TITLE: 450030 MULLION SECTION WINDLOAD CHART 5 450030 SECTION QUALITIES MULLION: Ixx = 3.398 in4 Sxx = 1.501 in3 MATERIAL PROPERTIES ALUMINUM MODULES: E = 10,100,000 psi STEEL MODULES: E = 29,000,000 psi 6063-T6 YIELD STRENGTH: Fy = 21,000 psi apexfacades.com 1.0 Meridian Pg- 37
Windload Charts WINDLOAD SPAN CHART 6 *DRAWING TITLE: 450030 WITH 2-450110 MULLION SECTION WINDLOAD CHART 6 450030 with (2) 450110 SECTION QUALITIES MULLION: Ixx = 5.924 in4 Sxx = 2.617 in3 MATERIAL PROPERTIES ALUMINUM MODULES: E = 10,100,000 psi STEEL MODULES: E = 29,000,000 psi 6063-T6 YIELD STRENGTH: Fy = 21,000 psi apexfacades.com 1.0 Meridian Pg- 38
Deadload Chart DEADLOAD 450050 SPAN CHART MULLION SECTION DEADLOAD CHART 1 450050 PROFILE QUALITIES MULLION: lyy = 0.4705 in4 Syy = 0.3842 in3 MATERIAL PROPERTIES ALUMINUM MODULES: E = 10,100,000 psi STEEL MODULES: E = 29,000,000 psi 6063-T6 YIELD STRENGTH: Fy = 21,000 psi *Please contact your local sales representative if you wish to access the full windload/deadload chart. apexfacades.com 1.0 Meridian Pg- 39
THIS PAGE INTENTIONALY LEFT BLANK apexfacades.com 1.0 Meridian Pg- 40
PARTS LIST apexfacades.com 1.0 Meridian Pg- 41
Parts List PART # CROSS SECTION DESCRIPTION NOTES 2" x 4 1/2" (51mm X 114mm) Mullion Shear Block frame assembly Standard Length 289" (7341mm) Available in split finish Ixx in4: 2.990 (mm4: 1,244,451) Iyy in4: 0.699 (mm4: 291,086) 450020 2" x 4 1/2" (51mm X 114mm) Door Jamb Shear Block frame assembly Standard Length 289" (7341mm) Available in split finish Ixx in4: 3.549 (mm4: 1,477,355) Iyy in4:.0804 (mm4: 334,815) 450030 2" x 4 1/2" (51mm X 114mm) Open Back Screw - spline frame assembly Standard Length 289" (7341mm) Available in split finish Ixx in4: 3.398 (mm4: 1,414,247) Iyy in4: 0.467 (mm4: 194,391) 450040 Open Back Filler Screw - spline frame assembly Standard Length 289" (7341mm) 2 parts required per Open Back Frame part number 450030 apexfacades.com 1.0 Meridian Pg- 42
Parts List PART # CROSS SECTION DESCRIPTION NOTES 450050 2" x 4 1/2" (51mm X 114mm) Transom Ixx in4: 2.491 (mm4: 1,036,694) Iyy in4: 0.394 (mm4: 163,904) Standard Length 289" (7341mm) Available in split finish 450060 4 1/2" x 4 1/2" (114mm X 114mm) 90 Corner Post, Part A Ixx in4: 3.842 (mm4: 1,599,171) Iyy in4: 1.171 (mm4: 487,221) Standard Length 289" (7341mm) Available in split finish See Architectural Details in this section 450070 4 1/2" x 4 1/2" (114mm X 114mm) 90 Corner Post, Part B Ixx in4: 3.949 (mm4: 1,643,911) Iyy in4: 1.258 (mm4: 523,721) Standard Length 289" (7341mm) Available in split finish See Architectural Details in this section apexfacades.com 1.0 Meridian Pg- 43
Parts List PART # CROSS SECTION DESCRIPTION NOTES 450080 4 1/2" x 4 1/2" (114mm X 114mm) T-Post, Part C Ixx in4: 4.026 (mm4: 1,675,745) Iyy in4: 1.253 (mm4: 521,403) Standard Length 289" (7341mm) Available in split finish See Architectural Details in this section 450090 Sill Track Ixx in4: 3.718 (mm4: 1,547,736) Iyy in4: 0.251 (mm4: 104,641) Standard Length 289" (7341mm) Available in split finish 450100 Head Receptor, Base Ixx in4: 3.635 (mm4: 1,512,915) Iyy in4: 0.213 (mm4: 88,617) Standard Length 289" (7341mm) Available in split finish apexfacades.com 1.0 Meridian Pg- 44
Parts List PART # CROSS SECTION DESCRIPTION NOTES 450110 Reinforcing Sleeve / Shear Block - Lineal Standard Length 289" (7341mm) Mill Finish 450110-B 24" (610mm) Splice Sleeve Mill Finish 450120 Transom Glass Stop Standard length 289" (7341mm) 450130 Snap-In Retainer Cap Standard length 289" (7341mm) For Use with Head Receptor 450100 450140 Door Stop For Crest 175 Doors Integration Standard length 256" (6502mm) For snap fit with part number 4500020-2" X 4 1/2" (51 X114mm) Split Door Jamb 200165 Door Stop Base Standard length 256" (6502mm) Mill Finish Snap fit with part 200170 - Door Stop 200170 Door Stop Cover Standard length 256" (6502mm) Snap fit with part 200165 - Door Stop Base 450155 Transom Glass Stop for 1" (25mm) IGU Standard length 289" (7341mm) 450160 Glass Stop for 0.250" (6mm) Single Glazing Standard length 289" (7341mm) 450170 Glazing Pocket Reducer for 0.250" (6mm) Single Glazing Standard length 289" (7341mm) apexfacades.com 1.0 Meridian Pg- 45
Parts List PART # CROSS SECTION DESCRIPTION NOTES 450110-A 1.125" (29mm) Shear Block Mill Finish 450180-A 1.125" (29mm) Universal Shear Block Mill Finish For use with 2" X 4 1/2" (51 X114mm) Transom Part number 450050 450190-A 1.38" (35mm) Deflector Mill Finish 450200-A Mounting Bracket - Machined, 8" (203mm) Long Mill Finish Fabricated with fastening holes Used where Deflection Header in not applied. 450210 16 Ga Aluminum Sill Track End Damb Plate Clear anodized 450220 16 Ga Aluminum Head Receptor End Dam Plate Clear Anodized apexfacades.com 1.0 Meridian Pg- 46
Parts List PART # CROSS SECTION DESCRIPTION NOTES 450231 Storefront Glazing Gasket Material/Duro: EPDM/60 Color: Black/Lubricated Unit: Roll 250 Feet (76M) 450240 Glazing Gasket Material/Duro: EPDM/60 Color: Black Unit: Roll 250 Feet (76M) Head/Sill Receptors, Corner Mullions 450250 5/8" X 1 1/4" (16mm X 32mm) Setting Block, 4" (102mm) Long 200220 1/4" x 1 1/8" (6 X 32mm) Setting Block, 4" (102mm) Long Material/Duro: Silicone/85 Color: Grey Unit: piece Material/Duro: Silicone/80 Color: Black Unit: piece 200245 Pile Weatherstripping, 3/8" (9mm) Height Material: Fin Seal Color: Grey Unit: Reel 1500 Feet (458M) 200260 High Performance Threshold Bulb Seal Material/Duro: TPE/60 Color: Black Unit: Reel 500 Feet (152M) For use at Latch Threshold 450245 W-Block, Anti-Walk Length: 1/2" (13mm) Material/Duro: EPDM/70 Color: Grey Unit: piece 450260 Door Jamb Socket Filler Length 170" (4320mm) Color: Black 450255 Door Seal Gasket Material/Duro: Peroxide EDPM/70 Color: Black Unit: Roll 200 Feet (61M) For use with Continuous Gear Hinge apexfacades.com 1.0 Meridian Pg- 47
Parts List PART # CROSS SECTION DESCRIPTION NOTES 450270 #10-1 1/2" Pan Head Zinc-Plated Self-Tapping Screw, Robertson Drive Shear block-to-mullion, mullion-to-transom attachment Unit: 100 piece 450280 #10-3/4" SS (18-8) CSK Self-Tapping Screw, Robertson Drive Connection of 90 Degree Corner Mullions to each other Unit: 100 piece 200310 #10-1/2" SS (18-8) PAN Head- Self-Tapping Screw, Robertson Drive 450290 #10-1/2" Pan Head Self-Drilling Screw, Zinc Coated, Robertson Drive 450300 #10-5/8" Flat Head Zinc-Plated Self-Drilling Screw, Robertson Drive Attachment of Door Stop Base part number 200165 to Mullion Attachment of Transom 450050 to Mullion 45010 via Shear Block 450110 Unit: 100 piece Attachment of Transom 450050 to Sill Track 450090 Unit: 100 piece Attachment of Glass Stop 450155 to Door Jamb 450020 Unit: 100 piece apexfacades.com 1.0 Meridian Pg- 48