. crealco C A S E M E N T 3 0. 5 CASEMENT 30.5 PRODUCT MANUAL 2013 Wispeco (Pty) Ltd, All Rights Reserved Revision: October 2013
. crealco C A S E M E N T 3 0. 5 Index Legal Disclaimer 5 Profile Identification 6-8 Hardware Identification 9 New Crimper 10 Butterfly Gasket and Wedge Codes 11 Sash Limitation Charts 12 Standard Top Hung 600Pa Windload 13 Standard Top Hung 1000Pa Windload 14 Standard Top Hung 1500Pa Windload 15 Standard Side Hung 600Pa Windload 16 Standard Side Hung 1000Pa Windload 17 Standard Side Hung 1500Pa Windload 18 Standard Top Hung Window Typical Configurations 19 Standard Side Hung Window Typical Configurations 20 Cottage Pane Window Fixed Panel Typical Configurations 21 Cottage Pane Window Top & Side Hung Typical Configurations 22 Fixing Details 23 Typical Cross Sectional Detail Double Top Hung Over Fixed 24 Typical Cross Sectional Detail Side Hung Over Fixed 25 Cottage Pane Typical Cross Sectional Detail 2 x 2 Top Hung Over 26 2x1 Fixed Panel Lite Window Typical Cross Sectional Detail Side Hung Over Fixed 27 Outer Frame Component Assembly Detail 28 Sash Frame Component Assembly Detail 29 Equal Leg Outer Frame Sill Level & Machining Detail 30 Unequal Leg Outer Frame Sill Level & Machining Detail 31 54mm Outer Frame Sill Level & Machining Detail 32 70mm Outer Frame Sill Level & Machining Detail 33 Lite Equal Leg Outer Frame Sill Level & Machining Detail 34 Standard Mullion Machining Detail For End Milling On Equal Leg 35 Outer Frame Standard Mullion Machining Detail For End Milling On Unequal Leg 36 Outer Frame Standard Mullion Machining Detail For End Milling On 54mm Outer 37 Frame This manual must be read in conjunction with the Installation, Cleaning and Maintenance Document, BEE Certificates and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront. PAGE 2
. crealco C A S E M E N T 3 0. 5 Index Standard Mullion Machining Detail For End Milling On 70mm Outer Frame Standard Mullion Machining Detail For End Milling On Lite Equal Leg Outer Frame Standard Transom With W/B Machining Detail For End Milling On Equal Leg Outer Frame Standard Transom With W/B Machining Detail For End Milling On Unequal Leg Outer Frame Standard Transom With W/B Machining Detail For End Milling On 54mm Outer Frame Standard Transom With W/B Machining For End Milling On 70mm Outer Frame Standard Transom With W/B Machining Detail For End Milling On Lite Equal Leg Outer Frame 54mm Mullion Machining Detail For End Milling On Equal Leg Outer Frame 54mm Mullion Machining Detail For End Milling On Unequal Leg Outer Frame 54mm Mullion Machining Detail For End Milling On 54mm Outer Frame 54mm Mullion Machining Detail For End Milling On 70mm Outer Frame 54mm Mullion Machining Detail For End Milling On Lite Equal Leg Outer Frame 70mm Mullion Machining Detail For End Milling On Equal Leg Outer Frame 70mm Mullion Machining Detail For End Milling On Unequal Leg Outer Frame 70mm Mullion Machining Detail For End Milling On 54mm Outer Frame 70mm Mullion Machining Detail For End Milling On 70mm Outer Frame 70mm Mullion Machining Detail For End Milling On Lite Equal Leg Outer Frame 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 This manual must be read in conjunction with the Installation, Cleaning and Maintenance Document, BEE Certificates and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront. PAGE 3
. crealco C A S E M E N T 3 0. 5 Index Cottage Pane Mullion Machining Detail For End milling On Equal Leg 55 Outer Frame Cottage Pane Mullion Machining Detail For End Milling On Unequal 56 Leg Outer Frame Cottage Pane Mullion Machining Detail For End Milling On 54mm 57 Outer Frame Cottage Pane Mullion Machining Detail For End Milling On 70mm 58 Outer Frame Cottage Pane Mullion Machining Detail For End Milling On Lite Equal 59 Leg Outer Frame Lite Mullion Machining Detail For End Milling On Equal Leg Outer 60 Frame Lite Mullion Machining Detail For End Milling On Unequal Leg Outer 61 Frame Lite Mullion Machining Detail For End Milling On 54mm Outer Frame 62 Lite Mullion Machining Detail For End Milling On 70mm Outer Frame 63 Lite Mullion Machining Detail For End Milling On Lite Equal Leg Outer 64 Frame Corner Cleat Assembly Detail For Tubular Sash 65 Corner Cleat Assembly Detail For Lite Tubular Sash 66 Glazing Bar Frame Joint Assembly Detail 67-68 Cross Joint Assembly Detail Standard Mullion 69 Cross Joint Assembly Detail Lite Mullion 70 Cross Joint Assembly Detail Cottage Pane Mullion 71 Glazing Procedure 72-73 Friction Assembly Detail 74 Handle Assembly Detail 75 Fixing Lug Preparation Detail 76 This manual must be read in conjunction with the Installation, Cleaning and Maintenance Document, BEE Certificates and the Performance Certificates for the relevant system. The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront. PAGE 4
. crealco C A S E M E N T 3 0. 5 LEGAL DISCLAIMER All information, recommendations or advice contained in this documentation is given in good faith to the best of Wispeco s knowledge and is based on current procedures in effect. Since the actual use of this documentation by the user is beyond the control of Wispeco, such use is within the exclusive responsibility of the user. Wispeco cannot be held responsible for any loss incurred through incorrect or faulty use of this documentation. Great care has been taken to ensure that the information provided is correct. Wispeco will accept no responsibility for any errors and/or omissions, which may have inadvertently occurred. All mechanical joints must be sealed with a Wispeco approved joint sealer. Laminated glass must not stand in water. All drawings in the Wispeco Documentation are shown NOT to scale. Wispeco cannot accept responsibility for the use of standard products since Wispeco does not know where these products are being installed. The use of anti-magnetic stainless steel screws and pop rivets is recommended to reduce galvanic corrosion in harsh environments. The hardware recommended in this documentation is suitable for use in most atmospheric environments. When hardware is used in severe costal environments the manufacturer of the hardware must be consulted. Fixing lugs on frames must be positioned as per the user manual and used in accordance to the AAAMSA specifications. When profiles are screwed together the screw centers must also be according to the user manual. All glass used within Wispeco products must comply with SAGGA regulations. By continuing to use this documentation you acknowledge that you understand and accept the legal disclaimer. PAGE 5
PROFILE IDENTIFICATION 30.50 FRAME 30mm EQ LEG STD W27990 30.50 FRAME 30mm UNEQ LEG STD W27992 30.50 SASH TUBULAR STANDARD W53631 70.00 FRAME 70mm W70968 32.00 SASH PICTURE FRAME W55441 54.38 FRAME 54mm W28481 28.20 BEAD 4 & 5mm W27991 PAGE 6
PROFILE IDENTIFICATION 30.50 CAS30.5 FRAME 30mm EQUAL LEG W32028 30.50 CAS30.5 FRAME 30mm UNEQUAL LEG W32027 30.50 CAS30.5 SASH TUBULAR W55684 30.50 CAS30.5 MULLION 30mm W55685 28.30 CAS30.5 BEAD MULTI 13mm GAP W31139 30.50 CAS30.5 MULLION 30mm ECONO W55008 27.77 CAS30.5 BEAD 6mm W28325 61.75 CAS30.5 FIXING LUG TWIST IN W28002 PAGE 7
PROFILE IDENTIFICATION 30.50 CAS30.5 MULLION 30mm STANDARD W53629 30.50 CAS30.5 MULLION 30mm WEATHER BAR W53630 54.00 CAS30.5 MULLION 54mm W54651 70.00 CAS30.5 MULLION 70mm W54652 40.00 CAS30.5 CORNER CLEAT 40mm W27989 30.50 CAS30.5 MULLION 30mm COTTAGE PANE W54867 PAGE 8
HARDWARE IDENTIFICATION CASEMENT 30.5 GLAZING BAR PACKER (BLACK) MP305 8x30 P/HEAD POSI S/S SCREW STPPS830 8x9 C/S HANDLE SCREW BLUNT POINT STPPS895 8x40 COUNTERSUNK POSI S/S SCREWS STCPS840 FRICTION STAY FS304BFG * MULTI FIXING LUG ALUM 15mm W30607 4.8 x 10 DOME RIVET DRP4810 EUROLINE PT HANDLE RIGHT/ LEFT HND004RHB HND004LHB 6.00 30.5 CROSS CONNECTOR (BLACK) CC305 7.00 30.5 CASELITE CORNER CLEAT CL52695 6.00 4 x 10 COUNTERSUNK RIVET CSKR410 9.00 4.80 FINPILE WP48500FG WEDGE H1 VR313FG WEDGE H42 VR5123FG BUTTERFLY H8 VP512FG BUTTERFLY H20 VP300FG * MAINTENANCE OF STAINLESS STEEL FRICTION STAYS To preserve the appearance and prevent corrosion, wipe down Friction Stays with warm water and a mild detergent. For stubborn dirt or stains, use a non corrosive cleaner, for more aggressive stains add a small amount of vinegar to water. Carbon steel brushes and steel wool should be avioded as they may leave particles embedded in the surface which may lead to rusting. After cleaning rinse with hot water and dry using a clean cloth. Cleaning is recommended once a month or more frequently when subjected to regular use or heavy soiling. PAGE 9
NEW CRIMPER ADJUSTMENT NUT UNIQUE SERIAL NUMBER UNIQUE TOOL SETS FOR EACH CASEMENT SYSTEM BENEFITS OF THE NEW CRIMPER: Double Toggle Clamps for better alignment of profiles. Simple & Quick precision adjustment to set profile crimping pressure. Unique multiple toolsets to cater for each casement system to ensure accurate crimping. Comprehensive manual available with crimper. Each crimper has a unique serial number for ease of maintenance. ADJUSTMENT NUT FOR QUICK & EASY CRIMPING PRESSURE SETTING ADJUSTMENTS ARE DONE JUST BY TURNING THE NUT. THE UNIQUE TOOL SETS FOR EACH SYSTEM AVAILABLE SEPARATELY ALLOWS FOR ACCURATE CRIMPING. THE NEW CRIMPER IS NOW AVAILABLE AT YOUR LOCAL STOCKIST PAGE 10
BUTTERFLY GASKET AND WEDGE CODES BUTTERFLY GASKET B01O W31139 BEAD W01G W02B W03R W04Y WEDGES 4 5 6 6.38 8.38 2 2 2 2 7 6 5 4.62 2 2.62 CASEMENT 30.5 WITH W31139 BEAD PAGE 11
SASH LIMITATION CHARTS Maximum Vent Width in mm Maximum Vent Height in mm Top Hung W53631 1000 750 1000.00 Maximum Vent Width in mm Maximum Vent Height in mm Side Hung W53631 600 1200 600.00 PAGE 12
STANDARD TOP HUNG 600Pa WINDLOAD NOTE: 1. SEE THE MULLION LIMITATION CHART 2. OPENING SIZES SHOWN IN RED 3. ACTUAL SIZES SHOWN IN BLACK AND BRACKETS. 600 (590) 900 (890) 1 200 (1190) 1 500 (1490) 1 800 (1790) 2 400 (2390) 600 (590) 30.5-0606T 30.5-0906T 30.5-1206T 30.5-1506T 30.5-1806TT 30.5-2406TT 900 (890) 30.5-0609T 30.5-0909T 30.5-1209T 30.5-1509T 30.5-1809TT 30.5-2409TT 1200 (1190) 30.5-0612T 30.5-0912T 30.5-1212DT 30.5-1512DT 30.5-1812DT 30.5-2412DT 1500 (1490) 30.5-0615DT 30.5-0915DT 30.5-1215DT 30.5-1515DT 30.5-1815DT 30.5-2415DT 1800 (1790) 30.5-0618DT 30.5-0918DT 30.5-1218DT 30.5-1518DT 30.5-1818DT 30.5-2418DT PAGE 13
STANDARD TOP HUNG 1000Pa WINDLOAD NOTE: 1. SEE THE MULLION LIMITATION CHART 2. OPENING SIZES SHOWN IN RED 3. ACTUAL SIZES SHOWN IN BLACK AND BRACKETS. 600 (590) 900 (890) 1 200 (1190) 1 500 (1490) 1 800 (1790) 2 400 (2390) 600 (590) 30.5-0606T 30.5-0906T 30.5-1206T 30.5-1506T 30.5-1806TT 30.5-2406TT 900 (890) 30.5-0609T 30.5-0909T 30.5-1209T 30.5-1509T 30.5-1809TT 30.5-2409TT 1200 (1190) 30.5-0612T 30.5-0912T 30.5-1212DT 30.5-1512DT 30.5-1812DT 30.5-2412DT 1500 (1490) 30.5-0615DT 30.5-0915DT 30.5-1215DT 30.5-1515DT 30.5-1815DT 30.5-2415DT 1800 (1790) 30.5-0618DT 30.5-0918DT 30.5-1218DT 30.5-1518DT 30.5-1818DT 30.5-2418DT PAGE 14
STANDARD TOP HUNG 1500Pa WINDLOAD NOTE: 1. SEE THE MULLION LIMITATION CHART 2. OPENING SIZES SHOWN IN RED 3. ACTUAL SIZES SHOWN IN BLACK AND BRACKETS. 600 (590) 900 (890) 1 200 (1190) 1 500 (1490) 1 800 (1790) 2 400 (2390) 600 (590) 30.5-0606T 30.5-0906T 30.5-1206T 30.5-1506T 30.5-1806TT 30.5-2406TT 900 (890) 30.5-0609T 30.5-0909T 30.5-1209T 30.5-1509T 30.5-1809TT 30.5-2409TT 1200 (1190) 30.5-0612T 30.5-0912T 30.5-1212DT 30.5-1512DT 30.5-1812DT 30.5-2412DT 1500 (1490) 30.5-0615DT 30.5-0915DT 30.5-1215DT 30.5-1515DT 30.5-1815DT 30.5-2415DT 1800 (1790) 30.5-0618DT 30.5-0918DT 30.5-1218DT 30.5-1518DT 30.5-1818DT 30.5-2418DT PAGE 15
STANDARD SIDE HUNG 600Pa WINDLOAD NOTE: 1. SEE THE MULLION LIMITATION CHART 2. OPENING SIZES SHOWN IN RED 3. ACTUAL SIZES SHOWN IN BLACK AND BRACKETS. 600 (590) 900 (890) 1 200 (1190) 1 500 (1490) 1 800 (1790) 2 400 (2390) 600 (590) 900 (890) 305-0609S 305-0909S 305-1209S 305-1509S 305-1809SS 305-2409SS 1200 (1190) 305-0612S 305-0912S 305-1212S 305-1512S 305-1812SS 305-2412SS 1500 (1490) 305-0615S 305-0915S 305-1215S 305-1515S 305-1815SS 305-2415SS 1800 (1790) 305-0618S 305-0918S 305-1218S 305-1518S 305-1818SS 305-2418SS PAGE 16
STANDARD SIDE HUNG 1000Pa WINDLOAD NOTE: 1. SEE THE MULLION LIMITATION CHART 2. OPENING SIZES SHOWN IN RED 3. ACTUAL SIZES SHOWN IN BLACK AND BRACKETS. 600 (590) 900 (890) 1 200 (1190) 1 500 (1490) 1 800 (1790) 2 400 (2390) 600 (590) 900 (890) 305-0609S 305-0909S 305-1209S 305-1509S 305-1809SS 305-2409SS 1200 (1190) 305-0612S 305-0912S 305-1212S 305-1512S 305-1812SS 305-2412SS 1500 (1490) 305-0615S 305-0915S 305-1215S 305-1515S 305-1815SS 305-2415SS 1800 (1790) 305-0618S 305-0918S 305-1218S 305-1518S 305-1818SS 305-2418SS PAGE 17
STANDARD SIDE HUNG 1500Pa WINDLOAD NOTE: 1. SEE THE MULLION LIMITATION CHART 2. OPENING SIZES SHOWN IN RED 3. ACTUAL SIZES SHOWN IN BLACK AND BRACKETS. 600 (590) 900 (890) 1 200 (1190) 1 500 (1490) 1 800 (1790) 2 400 (2390) 600 (590) 900 (890) 305-0609S 305-0909S 305-1209S 305-1509S 305-1809SS 305-2409SS 1200 (1190) 305-0612S 305-0912S 305-1212S 305-1512S 305-1812SS 305-2412SS 1500 (1490) 305-0615S 305-0915S 305-1215S 305-1515S 305-1815SS 305-2415SS 1800 (1790) 305-0618S 305-0918S 305-1218S 305-1518S 305-1818SS 305-2418SS PAGE 18
STANDARD TOP HUNG TYPICAL CONFIGURATIONS A SINGLE TOP HUNG BB TOP HUNG NEXT TO FIXED CC TOP HUNG NEXT TO TOP HUNG B TOP HUNG OVER FIXED C TOP HUNG OVER TOP HUNG E FIXED OVER TOP HUNG D DOUBLE TOP HUNG OVER FIXED DD FIXED OVER TOP HUNG OVER FIXED EE TRIPLE TOP HUNG PAGE 19
STANDARD SIDE HUNG TYPICAL CONFIGURATIONS A SINGLE SIDE HUNG B SIDE HUNG OVER FIXED C FIXED OVER SIDE HUNG D TOP HUNG OVER SIDE HUNG CC SIDE HUNG NEXT TO SIDE HUNG PAGE 20
COTTAGE PANE FIXED PANEL TYPICAL CONFIGURATIONS A 1 x 2 FIXED PANEL B 1 x 3 FIXED PANEL C 2 x 1 FIXED PANEL D 3 x 1 FIXED PANEL E 2 x 2 FIXED PANEL F 2 x 3 FIXED PANEL G 2 x 4 FIXED PANEL H 3 x 2 FIXED PANEL I 3 x 3 FIXED PANEL J 3 x 4 FIXED PANEL PAGE 21
COTTAGE PANE TOP HUNG & SIDE HUNG TYPICAL CONFIGURATIONS TOP HUNG P 2 x 1 PANE SINGLE TOP HUNG R 3 x 1 PANE SINGLE TOP HUNG Q 2 x 2 PANE SINGLE TOP HUNG S 3 x 2 PANE SINGLE TOP HUNG SIDE HUNG P 2 x 3 PANE SINGLE SIDE HUNG Q 2 x 4 PANE SINGLE SIDE HUNG PAGE 22
FIXING DETAILS 150 Max. 750 150 150 Max. 750 150 150 Max. 750 Max. 750 150 General: The window is fixed into position - the sill is then built at a later stage - the bottom lugs can be left in place but it is often found that most times the mason either bends them out of his way or breaks them off. This practically means that most windows are only secured on 3 sides. PAGE 23
TYPICAL CROSS SECTIONAL DETAIL DOUBLE TOP HUNG OVER FIXED SECTION B - B B SHOWING TRANSOM WITH WEATHER BAR OVERLAP A A C C B W53630 SECTION A - A W27990 W53631 W53631 22.68 53.26 55.76 W27991 SECTION C - C W27990 W53629 W27991 W27991 30.58 33.08 W27990 PAGE 24
TYPICAL CROSS SECTIONAL DETAIL SIDE HUNG OVER FIXED B SECTION B - B A A C C B W53631 SECTION A - A W27990 W53631 W53629 22.68 53.26 55.76 W27991 W27991 W27990 SECTION C - C W27990 W27991 30.58 33.08 PAGE 25
COTTAGE PANE TYPICAL CROSS SECTIONAL DETAIL 2 x 2 TOP HUNG OVER 2 x 1 FIXED PANEL SECTION B - B B A A C C W54867 B W53631 SECTION A - A W27990 W53631 W54867 W53629 22.68 W27991 53.26 55.76 SECTION C - C W27991 W27990 W54867 W27990 W27991 30.58 33.08 PAGE 26
LITE TYPICAL CROSS SECTIONAL DETAIL SIDE HUNG OVER FIXED B SECTION B - B A A C C B W50959 SECTION A - A W55009 W50959 W55008 W27991 22.68 W27991 53.26 55.76 W55009 SECTION C - C W55009 W27991 30.58 33.08 PAGE 27
OUTER FRAME COMPONENT ASSEMBLY DETAIL W27990 W27990 FINPILE W27989 CORNER CLEAT W27990 W27990 PAGE 28
SASH FRAME COMPONENT ASSEMBLY DETAIL W53631 W27989 CORNER CLEAT W53631 POP RIVETS HANDLE WITH SCREWS FRICTION STAY FINPILE PAGE 29
EQUAL LEG OUTER FRAME SILL LEVEL & MACHINING DETAIL W27990 W27990 45 W27990 W27990 FINISHED SILL LEVEL (INSIDE) FINISHED SILL LEVEL (OUTSIDE) PAGE 30
UNEQUAL LEG OUTER FRAME SILL LEVEL & MACHINING DETAIL W27992 W27992 45 W27992 FINISHED SILL LEVEL (INSIDE) W27992 FINISHED SILL LEVEL (OUTSIDE) PAGE 31
54mm OUTER FRAME SILL LEVEL & MACHINING DETAIL W28481 W28481 W28481 23.88 4.00 26.50 W28481 FINISHED SILL LEVEL (INSIDE) FINISHED SILL LEVEL (OUTSIDE) 40.10 23.50 PAGE 32
70mm OUTER FRAME SILL LEVEL & MACHINING DETAIL W70968 W70968 W70968 3.796 39.50 26.704 W70968 FINISHED SILL LEVEL (INSIDE) FINISHED SILL LEVEL (OUTSIDE) 34.284 50.50 PAGE 33
LITE EQUAL LEG OUTER FRAME SILL LEVEL & MACHINING DETAIL W55009 W55009 45 W55009 W55009 FINISHED SILL LEVEL (INSIDE) FINISHED SILL LEVEL (OUTSIDE) PAGE 34
STANDARD MULLION MACHINING DETAIL FOR END MILLING ON EQUAL LEG OUTER FRAME W53629 STANDARD MULLION W53629 EXPLODED VIEW ISOMETRIC VIEW W27990 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 35
STANDARD MULLION MACHINING DETAIL FOR END MILLING ON UNEQUAL LEG OUTER FRAME W53629 STANDARD MULLION W53629 EXPLODED VIEW ISOMETRIC VIEW W27992 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 36
STANDARD MULLION MACHINING DETAIL FOR END MILLING ON 54mm OUTER FRAME W53629 STANDARD MULLION W53629 EXPLODED VIEW W28481 ISOMETRIC VIEW 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 37
STANDARD MULLION MACHINING DETAIL FOR END MILLING ON 70mm OUTER FRAME W53629 STANDARD MULLION W53629 EXPLODED VIEW W70968 ISOMETRIC VIEW 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 38
STANDARD MULLION MACHINING DETAIL FOR END MILLING ON LITE EQUAL LEG OUTER FRAME W53629 STANDARD MULLION W53629 EXPLODED VIEW ISOMETRIC VIEW W55009 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 39
STANDARD TRANSOM WITH W/B MACHINING DETAIL FOR END MILLING ON EQUAL LEG OUTER FRAME EXPLODED VIEW SHOWING TRANSOM W27990 STANDARD TRANSOM WITH W/B W53630 W53630 ISOMETRIC VIEW SHOWING TRANSOM 61.80 28.00 23.00 8.50 4.00 2.50 24.00 13.00 PAGE 40
STANDARD TRANSOM WITH W/B MACHINING DETAIL FOR END MILLING ON UNEQUAL LEG OUTER FRAME EXPLODED VIEW SHOWING TRANSOM W27992 STANDARD TRANSOM WITH W/B W53630 W53630 ISOMETRIC VIEW SHOWING TRANSOM 61.80 28.00 23.00 8.50 4.00 2.50 24.00 13.00 PAGE 41
STANDARD TRANSOM WITH W/B MACHINING DETAIL FOR END MILLING ON 54mm OUTER FRAME EXPLODED VIEW SHOWING TRANSOM W28481 STANDARD TRANSOM WITH W/B W53630 W53630 ISOMETRIC VIEW SHOWING TRANSOM 61.80 28.00 23.00 8.50 4.00 2.50 24.00 13.00 PAGE 42
STANDARD TRANSOM WITH W/B MACHINING DETAIL FOR END MILLING ON 70mm OUTER FRAME EXPLODED VIEW SHOWING TRANSOM W70968 STANDARD TRANSOM WITH W/B W53630 W53630 ISOMETRIC VIEW SHOWING TRANSOM 61.80 28.00 23.00 8.50 4.00 2.50 24.00 13.00 PAGE 43
STANDARD TRANSOM WITH W/B MACHINING DETAIL FOR END MILLING ON LITE EQUAL LEG OUTER FRAME EXPLODED VIEW SHOWING TRANSOM W55009 STANDARD TRANSOM WITH W/B W53630 W53630 ISOMETRIC VIEW SHOWING TRANSOM 61.80 28.00 23.00 8.50 4.00 2.50 24.00 13.00 PAGE 44
54mm MULLION MACHINING DETAIL FOR END MILLING ON EQUAL LEG OUTER FRAME W54651 54mm MULLION W54651 EXPLODED VIEW W27990 ISOMETRIC VIEW 61.80 28.60 28.00 23.00 4.00 2.50 24.00 23.50 PAGE 45
54mm MULLION MACHINING DETAIL FOR END MILLING ON UNEQUAL LEG OUTER FRAME W54651 54mm MULLION W54651 EXPLODED VIEW W27992 ISOMETRIC VIEW 61.80 28.60 28.00 23.00 4.00 2.50 24.00 23.50 PAGE 46
54mm MULLION MACHINING DETAIL FOR END MILLING ON 54mm OUTER FRAME W54651 54mm MULLION W54651 EXPLODED VIEW ISOMETRIC VIEW W28481 61.80 28.60 23.00 4.00 23.50 24.00 2.50 PAGE 47
54mm MULLION MACHINING DETAIL FOR END MILLING ON 70mm OUTER FRAME W54651 54mm MULLION W54651 EXPLODED VIEW ISOMETRIC VIEW W70968 61.80 28.60 23.00 3.80 23.50 24.20 2.50 PAGE 48
54mm MULLION MACHINING DETAIL FOR END MILLING ON LITE EQUAL LEG OUTER FRAME W54651 54mm MULLION W54651 EXPLODED VIEW W55009 ISOMETRIC VIEW 61.80 28.60 28.00 23.00 4.00 2.50 24.00 23.50 PAGE 49
70mm MULLION MACHINING DETAIL FOR END MILLING ON EQUAL LEG OUTER FRAME W54652 70mm MULLION W54652 EXPLODED VIEW W27990 61.80 28.60 ISOMETRIC VIEW 28.00 23.00 39.50 4.00 2.50 24.00 PAGE 50
70mm MULLION MACHINING DETAIL FOR END MILLING ON UNEQUAL LEG OUTER FRAME W54652 70mm MULLION W54652 EXPLODED VIEW W27992 61.80 28.60 ISOMETRIC VIEW 28.00 23.00 39.50 4.00 2.50 24.00 PAGE 51
70mm MULLION MACHINING DETAIL FOR END MILLING ON 54mm OUTER FRAME W54652 EXPLODED VIEW 70mm MULLION W54652 ISOMETRIC VIEW W28481 61.80 28.60 28.00 23.00 15.60 23.90 4.00 2.50 24.00 PAGE 52
70mm MULLION MACHINING DETAIL FOR END MILLING ON 70mm OUTER FRAME W54652 70mm MULLION W54652 EXPLODED VIEW ISOMETRIC VIEW W70968 61.80 28.60 23.00 4.00 39.50 24.00 2.50 PAGE 53
70mm MULLION MACHINING DETAIL FOR END MILLING ON LITE EQUAL LEG OUTER FRAME W54652 70mm MULLION W54652 EXPLODED VIEW W55009 61.80 28.60 ISOMETRIC VIEW 28.00 23.00 39.50 4.00 2.50 24.00 PAGE 54
COTTAGE PANE MULLION MACHINING DETAIL FOR END MILLING ON EQUAL LEG OUTER FRAME W54867 COTTAGE PANE MULLION W54867 EXPLODED VIEW W27990 ISOMETRIC VIEW 47.80 14.00 9.00 4.00 2.50 24.00 PAGE 55
COTTAGE PANE MULLION MACHINING DETAIL FOR END MILLING ON UNEQUAL LEG OUTER FRAME W54867 COTTAGE PANE MULLION W54867 EXPLODED VIEW W27992 ISOMETRIC VIEW 47.80 14.00 9.00 4.00 2.50 24.00 PAGE 56
COTTAGE PANE MULLION MACHINING DETAIL FOR END MILLING ON 54mm OUTER FRAME W54867 COTTAGE PANE MULLION W54867 EXPLODED VIEW W28481 ISOMETRIC VIEW 47.80 14.00 9.00 4.00 2.50 24.00 PAGE 57
COTTAGE PANE MULLION MACHINING DETAIL FOR END MILLING ON 70mm OUTER FRAME W54867 COTTAGE PANE MULLION W54867 EXPLODED VIEW W70968 ISOMETRIC VIEW 47.80 14.00 9.00 4.00 2.50 24.00 PAGE 58
COTTAGE PANE MULLION MACHINING DETAIL FOR END MILLING ON LITE EQUAL LEG OUTER FRAME W54867 COTTAGE PANE MULLION W54867 EXPLODED VIEW W55009 ISOMETRIC VIEW 47.80 14.00 9.00 4.00 2.50 24.00 PAGE 59
LITE MULLION MACHINING DETAIL FOR END MILLING ON EQUAL LEG OUTER FRAME W55008 LITE MULLION W55008 EXPLODED VIEW ISOMETRIC VIEW W27990 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 60
LITE MULLION MACHINING DETAIL FOR END MILLING ON UNEQUAL LEG OUTER FRAME W55008 LITE MULLION W55008 EXPLODED VIEW ISOMETRIC VIEW W27992 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 61
LITE MULLION MACHINING DETAIL FOR END MILLING ON 54mm OUTER FRAME W55008 LITE MULLION W55008 EXPLODED VIEW W28481 ISOMETRIC VIEW 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 62
LITE MULLION MACHINING DETAIL FOR END MILLING ON 70mm OUTER FRAME W55008 LITE MULLION W55008 EXPLODED VIEW W70968 ISOMETRIC VIEW 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 63
LITE MULLION MACHINING DETAIL FOR END MILLING ON LITE EQUAL LEG OUTER FRAME W55008 LITE MULLION W55008 EXPLODED VIEW ISOMETRIC VIEW W55009 61.80 28.00 4.00 23.00 2.50 24.00 PAGE 64
CORNER CLEAT ASSEMBLY DETAIL FOR TUBULAR SASH NOTE: ALL JOINTS MUST BE SEALED WITH SMALL JOINT SEALANT. FINPILE MUST BE FITTED TO SASH AND CORRESPONDING SURFACES OF FRAME BEFORE CRIMPING (NOT TO AREAS TO BE GLAZED) W27989 W53631 THE CORNER CLEAT HAS BEEN SPECIALLY DESIGNED SO THAT THE CORNER CAN BE CRIMPED EITHER FROM THE INSIDE WITH A HAND OPERATED CRIMPING MACHINE OR FROM THE OUTSIDE WITH A HYDRAULICALLY OPERATED CRIMPING MACHINE W27989 PAGE 65
CORNER CLEAT ASSEMBLY DETAIL FOR LITE TUBULAR SASH NOTE: ALL JOINTS MUST BE SEALED WITH SMALL JOINT SEALANT. FINPILE MUST BE FITTED TO SASH AND CORRESPONDING SURFACES OF FRAME BEFORE CRIMPING (NOT TO AREAS TO BE GLAZED) W27989 W50959 THE CORNER CLEAT HAS BEEN SPECIALLY DESIGNED SO THAT THE CORNER CAN BE CRIMPED EITHER FROM THE INSIDE WITH A HAND OPERATED CRIMPING MACHINE OR FROM THE OUTSIDE WITH A HYDRAULICALLY OPERATED CRIMPING MACHINE W27989 PAGE 66
GLAZING BAR FRAME JOINT ASSEMBLY DETAIL NOTE: ALL JOINTS MUST BE SEALED WITH SMALL JOINT SEALANT. FINPILE MUST BE FITTED PRIOR TO ASSEMBLY IF SASH IS TO BE FITTED INTO FRAME. FINPLIE MUST NOT RUN BEHIND GLAZING BAR AND GAP MUST BE SEALED TO PREVENT WATER INFILTRATION. W53629 W53631 MP305 ø 4.8mm HOLES 14mm c/c STPPS830 PAGE 67
GLAZING BAR FRAME JOINT ASSEMBLY DETAIL NOTE: ALL JOINTS MUST BE SEALED WITH SMALL JOINT SEALANT. FINPILE MUST BE FITTED PRIOR TO ASSEMBLY IF SASH IS TO BE FITTED INTO FRAME. FINPLIE MUST NOT RUN BEHIND GLAZING BAR AND GAP MUST BE SEALED TO PREVENT WATER INFILTRATION. W55008 W50959 MP305 ø 4.8mm HOLES 14mm c/c STPPS830 PAGE 68
CROSS JOINT ASSEMBLY DETAIL STANDARD MULLION NOTE: ALL JOINTS MUST BE SEALED WITH SMALL JOINT SEALANT. FINPILE MUST BE FITTED PRIOR TO ASSEMBLY IF SASH IS TO BE FITTED INTO FRAME. FINPILE MUST NOT RUN BEHIND GLAZING BAR AND GAP MUST BE SEALED TO PREVENT WATER INFILTRATION. MULLION ENDS MILLED TO ENGAGE MULLION W53629 8x30 P/HEAD POSI S/S ST SCREW STPPS830 W53629 CC305 SHOWING FINPILE MEETING AND NOT RUNNING TO EDGE OF THE PROFILE SILICONE SEALANT PAGE 69
CROSS JOINT ASSEMBLY DETAIL LITE MULLION NOTE: ALL JOINTS MUST BE SEALED WITH SMALL JOINT SEALANT. FINPILE MUST BE FITTED PRIOR TO ASSEMBLY IF SASH IS TO BE FITTED INTO FRAME. FINPILE MUST NOT RUN BEHIND GLAZING BAR AND GAP MUST BE SEALED TO PREVENT WATER INFILTRATION. MULLION ENDS MILLED TO ENGAGE MULLION W55008 8x30 P/HEAD POSI S/S ST SCREW STPPS830 W55008 CC305 SHOWING FINPILE MEETING AND NOT RUNNING TO EDGE OF THE PROFILE SILICONE SEALANT PAGE 70
CROSS JOINT ASSEMBLY DETAIL COTTAGE PANE MULLION W54867 MULLION ENDS MILLED TO ENGAGE MULLION 6x30 P/HEAD POSI S/S ST SCREW STPPS630 W54867 CPC28 NOTE: ALL JOINTS MUST BE SEALED WITH SMALL JOINT SEALANT. FINPILE MUST BE FITTED PRIOR TO ASSEMBLY IF SASH IS TO BE FITTED INTO FRAME. FINPILE MUST NOT RUN BEHIND GLAZING BAR AND GAP MUST BE SEALED TO PREVENT WATER INFILTRATION. PAGE 71
GLAZING PROCEDURE Insert the pull-in vinyl gasket into glazing beads by sliding or pressing it into the groove (1). Before cutting gasket, ensure that it has not stretched and cut 6mm longer so that corners are in compression at all times. 1 Position bottom glazing bead in glazing bead rebate (2). Place glass on glazing blocks (3). Insert top and then side glazing beads ensuring that they are in correctly. Starting from top centre, insert roll in gasket (4) without stretching it (5). Stop 150mm from corner and partly cut gasket 6mm longer than the edge of the vertical bead. Insert gasket at corner and then roll in remaining 150mm. Repeat this on the other sides. Where gasket ends meet, cut gasket 6mm longer. Insert cut ends first and complete. 6mm GLASS 3 AND 4mm GLASS 2 GLAZING BLOCK 3 ENSURE GASKETS ARE NOT STRETCHED AT ANY STAGE TOP SEEN FROM THE INSIDE START END NOTCH GASKET AT CORNERS 4 5 PAGE 72
GLAZING PROCEDURE GLAZING 1. SELECTION OF GLAZING METHODS 1.1 SETTING AND LOCATION BLOCKS Glass-to-metal contact must be avoided at all times by using setting and location blocks having a hardness of 50 to 90 shore A durometer. Use only blocks made of Neoprene, EPDM, Silicone or other elastomeric material. Setting blocks are to have a minimum thickness of 3mm and must be at least 27mm in length per square metre of glass area. The position of the setting and location blocks is illustrated in Figure 2. SB over pivot SB over pivot a) Fixed Light b) Vertically pivoted (hung off-centre) c) Vertically pivoted (hung centrally) d) Top Hung e) Bottom Hung f) Side Hung or door g) Horizontally pivoted and reversible h) Horizontally sliding; 6 blocks to each pane i) Vertically sliding FIGURE 2 - POSITION OF SETTING AND LOCATION BLOCKS PAGE 73
FRICTION STAY ASSEMBLY DETAIL 14.00 FRAME SASH INSIDE THE FRICTION STAY SHOULD ALWAYS BE FITTED AS FAR FORWARD IN THE FRAME AS POSSIBLE. (AS ILLUSTRATED) THE ARM FIXED TO THE SASH SHOULD BE FITTED TO ALLOW CORRECT COMPRESSION OF THE FINPILE AND PACKED TO CLEAR GLAZING BEAD NIB. THE STAYS ARE SECURED WITH 4.8 x 10 DOME HEAD RIVETS. STAY CODE FS202FG FS304FG FS406FG FS508FG FS600FG TO BE USED FOR SASH SIZE LESS THAN OR EQUAL TO 300mm BETWEEN 301mm AND 450mm BETWEEN 451mm AND 600mm BETWEEN 601mm AND 750mm GREATER THAN 750mm PAGE 74
HANDLE ASSEMBLY DETAIL W53631 NO 8 x 10 COUNTERSUNK SELF-TAPPING FLAT END SCREWS ø 3.5mm 30.50 W53631 PAGE 75
FIXING LUG PREPARATION DETAIL TWIST IN LUG FITTED TO EQUAL LEG OUTER FRAME TWIST IN LUG FITTED TO UNEQUAL LEG OUTER FRAME PAGE 76