Made to Measure Window Furnishings. Awnings Product Manual

Made to Measure Window Furnishings Awnings Product Manual Page No. 1

Awnings Product Manual Contents for Module 1. Overview Operation & Advantages Product Overview & Operation Options 2. Fabrics Fabric Options Important Information 3. Awning Products Product Details Awning Mounting Brackets Automation 4. Measuring Guidelines 5. Guidelines for Safe Awning Use 6. Common Problems, Causes & Solutions 7. Summary 8. Knowledge & Learning Assessment Test 9. Appendix Page No. 2

Overview Operation & Advantages Summer Cool Leaving the Heat Outside (from CSIRO Home Energy Savings Book & Energy Australia) Window Awnings that Reflect up to 70% of the Heat & Save Energy Effectiveness The same window that is a useful source of heat & light can sometimes be a nuisance letting in heat when you don t need it or leaking away as much as 40% of your home heating or cooling energy. Each degree lower that a home air conditioner operates at can save up to 10% of energy cooling costs These problems can be reduced through the installation using one of the following exterior awnings Straight Drop Pivot Arm Folding Arm Awnings for Alfresco Living Folding Arm Awnings are an ideal solution to provide protection from the sun, shade & ambience for alfresco living Open awning with or without a hood Semi-Cassette Awning Full Cassette Awning 40% External Awnings Internal Blinds Page No. 4

Awnings Overview Product Overview & Operation Options Operation Options Product Family Not Guided Straight Drop Awnings Side Guided Pivot Arm Awnings Folding Arm Awnings Armidale Straight Drop Veranda (Rope & Pulley Operation) Manual Operation Comboyne Straight Drop (Convertible) (Tape & Reel Operation) Leura Open Style - Not Guided Manual Gear Box Operated Glenbrook Full Cassette Style - Not Guided Manual Gear Box Operated Kirribilli Multi-Stop Channel Guide (Channel Side Guided Bottom Bar) Manual Operation (Spring Locking Bottom Bar) Windsor Traditional Automatic (Steel Rod Guided Bottom bar) Richmond Maxishade Automatic (Steel Rod Guided Bottom bar) Manual or Motorised Narooma Open Style Mornington Full Cassette Style Stainless Steel Wire Guided Bottom Bar Oberon Bundanoon Brunswick Pivot Arm (Tape & Reel Operation) Bundeena Standard (Open) Folding Arm Avalon Open Style Full Cassette Style Channel Guided Bottom Bar Full Cassette Folding Arm Page No. 5

Fabric Collection for JPM Awnings Quality Fabrics with 5 to 10 year Warranties Sold in Australia by Defab as Somerton www.para.it Sunbrella fabric s 10-year limited warranty for awnings www.sunbrella.com www.novacorp.co.kr Page No. 7

Fabric Collection for JPM Awnings Retailers must sell fabrics JPM stock for JPM Awnings JPM Awnings will only be supplied fitted with JPM stocked fabrics that are indicated available in; Para Acrylic swatch book Sunbrella Acrylic marked up swatch book Nova Sunscreen swatches as detailed Page No. 8

Fabric Collection for JPM Awnings - - Para, Italy Acrylic Fabrics Stocked by JPM 11 popular colour fabrics Use fabric swatch samples for exact colours All seams are stitched with high quality Tenara Teflon thread - Resistant to UV degradation (rotting) Beige 929 Bone 15/14 Medium Grey 94/15 Light Grey 79 Butter 93 Khaki 14 Charcoal 97 Navy/Butter 879 Cedar/Butter 877 Charcoal/Butter 876 Light Cream 15/93 Page No. 9

Fabric Collection for JPM Awnings Selected Acrylic Fabrics from Sunbrella Swatch Book 54 Fabrics - Purchased in Cut to Size Pieces by JPM Fabric details inside Sunbrella swatch book Page No. 10

Fabric Collection for JPM Awnings Selected Acrylic Fabrics from Sunbrella Swatch Book 54 Fabrics - Purchased in Cut to Size Pieces by JPM Sunbrella - Pacific Blue Sunbrella - Sunflower Yellow Sunbrella - Jockey Red Sunbrella - Natural Sunbrella - Black Sunbrella - Mocha Tweed Sunbrella - Beige Sunbrella - True Brown Sunbrella - Navy Sunbrella - Salmon Sunbrella - Toast Sunbrella - Cadet Grey Sunbrella - Burgundy Sunbrella - Linen Sunbrella - Forest Green Sunbrella - Black Cherry Sunbrella - Sapphire Blue Sunbrella - Oyster Sunbrella - Charcoal Grey Sunbrella - Captain Navy Sunbrella - Taupe Sunbrella - Mediterranean Blue Sunbrella - Linen Tweed Sunbrella - Tresco Brass Sunbrella - Aspen Sunbrella - Fern Sunbrella - Heather Beige Sunbrella - Spa Sunbrella - Wheat Sunbrella - Marine Blue Sunbrella - Mineral Blue Sunbrella - Basil Sunbrella - Ruse Sunbrella - Tresco Linen Sunbrella - Tresco Clay Sunbrella - Tresco Brick Sunbrella - Ombre Dark Brown / Salmon / Beige Sunbrella - Manhattan Charcoal Sunbrella - Manhattan Classic Sunbrella - Forest Green Fancy Sunbrella - Mabry Slate Sunbrella - Eastland Lagoon Sunbrella - Eastland Classic Sunbrella - Westfield Salsa Sunbrella - Westfield Mushroom Sunbrella - Captain Navy / Natural Classic Sunbrella - Taupe Bar Sunbrella - Forest Green Tansitional Sunbrella - Mediterranean Canvas Block Stripe Sunbrella - Black Forest Fancy Sunbrella - Forest Green / Beige / Natural Fancy Stripe Sunbrella - Sand Gradutated Stripe Sunbrella - Fern Classic Sunbrella - Putty Regimental Page No. 11

Fabric Collection for JPM Awnings Polyester / PVC Sunscreen Mesh Fabrics Nova, Korea Fabrics Ex. Stock by JPM NOVA SUNSCREEN SOLSCAPE - E1 Colour Pattern No. White E1-1003 Beige E1-2007 Champagne E1-2004 Charcoal E1-3003 Black E1-10001 Solscape E1 8% openness Architectural grade fabric NOVA SUNSCREEN SOLSCAPE - E2 Colour Pattern No. White E2-1005 Beige E2-2008 Chanmpagne E2-2011 Charcoal E2-3007 Black E2-10002 NOVA SUNSCREEN HIGHSHADE Colour Pattern No. White DN 001 Beige DN 002 Champagne DN 005 Charcoal DN 906 Black DN 914 Solscape E2 16% openness Architectural grade fabric Highshade 5% openness 2 x 2 weave fabric Page No. 12

Not Recommended Fabric Collection for JPM Awnings Fabric Range Specifications for JPM Awnings Fabric Material Fabric Openness Factor Width (mm) Weight (gsm) Thickness (mm) Mesh Weave Railroad Fabric Colours 100% Acrylic JPM Para Glen Raven Sunbrella 98% Blockout 1,200 290 0.64 30 x 15 11 colours 50 selected colours from Sunbrella catalogue Polyester/PVC Sunscreen Mesh Architectural Polyester/PVC Sunscreen Mesh NOVA Highshade 5% 3,000 514 0.73 2 x 2 Yes White, Beige, Champagne, Charcoal & Black Nova Solscape E1 8% 3,000 400 0.54 1 x 1 Yes White, Beige, Champagne, Charcoal & Black NOVA Solscape E2 16% 2,500 370 0.4 1 x 1 Yes White, Beige, Champagne, Charcoal & Black Acrylic Use for F.A.A., Straight Drop & Pivot Arm Awnings Most popular awning block out fabric 98% UV filter. 2% coming through is not harmful Yarn 100% solution dyed before weaving Pattern on front & back Partially translucent but no glare coming through Light weight fabric used for most folding arm awnings. Fabric will fade but durable yarns will last 7 to 15 years Sunscreen Mesh Fabric Not for F.A.A. Polyester yarns coated with PVC & oven cured Enjoy view with reduced glare & some shade Not a block our material lets air & wind pass through Page No. 13

JPM Awning Metal Colours Colour Options Awning Type RAL No. 9001 1015 JPM Product Name Paint Gloss Level - Measures using a Novo- Gloss Rhopoint 60 deg Meter 97% 73% 45% 54% 58% 76% 63% Pearl White (Gloss) Colours Available Classic Cream (Gloss) Citi Pearl Grey (Satin) Night Sky Black (Satin) Colours Release Date Woodland Grey (Satin) 2012/13, T.B.C. Sandbank (Satin) Pale Eucalypt (Satin) Open Folding Arm Awning up to 6 m wide Yes Yes Yes No No No No BUNDEENA Extruded Aluminium Top Cover = Hood Yes Yes Yes No No No No Full Cassette Folding Arm Awning up to 6 m wide Auto Guide Awning, with Painted Steel Hood Automatic, with Painted Steel Hood Multi Stop Channel Pivot Arm Awning, with Painted Steel Hood AVALON Yes Yes Yes No No No No WINDSOR Yes Yes No Yes Yes Yes Yes RICHMOND Yes Yes No Yes Yes Yes Yes KIRRIBILLI Yes Yes No Yes Yes Yes Yes BRUNSWICK Yes Yes No Yes Yes Yes Yes Verandah Straight Drop Cord (or Tape?) & Reel Open S.S. Wire Guide - Bottom Bar Open S.S. Wire Guide - Painted Steel Hood ARMIDALE COMBOYNE NAROOMA Not Painted Yes Yes Yes No No No No Yes Yes No No Yes No No Full Cassette Wire Guide MORNINGTON Yes Yes Yes No No No No Open Channel Guide - Bottom Bar & Side Channels Open Channel Guide - Painted Steel Hood OBERON Yes Yes No No No No No Yes Yes No No Yes No No Full Cassette Channel Guide BUNDANOON Yes Yes Yes No No No No Page No. 14

Important Information AWNING FABRIC CHARACTERISTICS The manufacture of fabric is strictly monitored in order to achieve premium quality. However, the sewn fabric in finished awnings, certain irregularities may appear that are inherent to the manufacturing process itself. These visual anomalies do not diminish product quality and cannot be regarded as defects and therefore cannot serve as the basis for a claim. WRINKLES PRODUCED BY FOLDING If awnings are folded during their manufacture, creases may appear that, when viewed in the cross-light and especially with light colours, seem to be streaks of dirt. RIPPLES ALONG THE SEAMS The awning fabric is generally made up to the required width from rolls of fabric and as a result the fabric is double thickness at the seams. When the awning is rolled up and opened the double thickness at seams, along the width of the fabric, may produce stretching and a slight waviness. These irregularities appear more pronounced in lighter coloured fabrics Page No. 15

Important Information FABRIC WAVERING Straight drop & folding arm awnings will roll up reasonably evenly but like any large blind it will show fabric wavering, this is because it is impossible to make a large piece of fabric hang perfectly flat. This generally appears on awnings wider than 2,000mm and or drops greater than 3,000mm. RAILROADING Check for fabrics that may be railroaded particularly for straight drop blinds. Always inform the client that larger widths that are railroaded WILL wave & ripple. FABRIC SEAM POSITIONS Check the fabric width to determine if there will be any seams. Particularly if using Sunscreen fabric. Standard seams are vertical & the position of seams & any impact to views MUST be discussed with the customer & the position of seams should be specified & approved. Page No. 16

Awnings Overview Product Overview & Operation Options Manual Operated Unguided Straight Drop Awnings Operation Options Product Family Not Guided Straight Drop Awnings Side Guided Pivot Arm Awnings Folding Arm Awnings Armidale Straight Drop Veranda (Rope & Pulley Operation) Manual Operation Comboyne Straight Drop (Convertible) (Tape & Reel Operation) Leura Open Style - Not Guided Manual Gear Box Operated Glenbrook Full Cassette Style - Not Guided Manual Gear Box Operated Manual Operation (Spring Locking Bottom Bar) Manual or Motorised Page No. 18

Product Details ARMIDALE - Straight Drop Veranda Exposed Cord & Pulley Operation A cost & energy efficient full drop (bottom roll up) blind with an aluminium sail track head rail for fixing to the building. External rope & pulley operation. Suitable for; Windows & glass doors Butt join several blinds along veranda's Maximum Sizes Width; up to 4,500mm (1 to 2 person operation) Drop; up to 3,000 depending on width. Options to Specify Strap adaptors on bottom bar end caps & hold down straps Breeching staples for fixing to building for full drop securing. ANGLED TOP for an additional cost Installation Guide Face Fit, Fascia Fit, Recess Fit or Top Fix Install wall cleat 1,600mm min above ground level & wrap up cord out of reach from children Page No. 19

Product Details COMBOYNE - Straight Drop Convertible Cord & Reel Operation Top down Cord & Reel manual operation suitable for; Windows & glass doors Veranda protection where spool light gaps are acceptable Maximum Sizes Width; 4,500mm Drop; 3,000mm Standard Components Convertible rope & spool mechanism: Rope cleat to secure 50mm dia. Galvanised steel bottom tube Options to Specify Strap adaptors on bottom bar end caps & hold down straps Breeching staples for fixing to building Acrylic Blockout or Sunscreen mesh fabric Not suitable for clear P.V.C Installation Guide Centre distance between posts less spool (check light gaps) Face Fit, Fascia Fit Mount 150mm (2 bricks) above window Not suitable for recess fit due to spool gap Install wall cleat 1,600mm min above ground level & wrap up cord out of reach from children Page No. 20

Product Details LEURA Open & Unguided Straight Drop Manual Gear Box Operation Application Full shading of external windows & balconies with the option to hold down in the bottom position using a hold down kit, comprising of bottom bar tie down runners, hold down straps & breeching staples Maximum Sizes Width; 5,400 Drop; 3,000 Standard Components Manual gear box - Top roll operation Aluminium tear drop profile bottom bar up to 5,400mm wide Acrylic block out or Sunscreen fabric Options to Specify Open Overroll style painted steel hood Bottom bar strap tie down runners, straps & breeching staples Installation Face Fit or Recess Fit Page No. 21

Product Details GLENBROOK - Full Cassette & Unguided Straight Drop Manual Gear Box Operation Application Full shading of external windows & balconies with the Sizes option to hold down in the bottom position using a hold down kit, comprising of bottom bar tie down runners, hold down straps & breeching staples Width; 5,400mm maximum width Drop; 3,000mm maximum drop Standard Components 95 or 125mm deep powder coat painted aluminium cassette head box Manual gear box - Top roll operation Aluminium tear drop profile bottom bar Options to Specify Acrylic block out or sunscreen fabric Bottom bar strap runners & straps Installation Face Fit or Recess Fit Page No. 22

Awnings Overview Product Overview & Operation Options Manual Operated Side Guided, Spring Locking Bottom Bar Awnings Operation Options Product Family Not Guided Straight Drop Awnings Side Guided Pivot Arm Awnings Folding Arm Awnings Manual Operation Kirribilli Multi-Stop Channel Guide (Channel Side Guided Bottom Bar) Manual Operation (Spring Locking Bottom Bar) Windsor Traditional Automatic (Steel Rod Guided Bottom bar) Richmond Maxishade Automatic (Steel Rod Guided Bottom bar) Manual or Motorised Page No. 23

Product Details KIRRIBILLI - Multi Stop Channel Guide Awning Multistop awnings can be mounted either between posts or on the face of a window. A key feature of the product is that it can be dropped to any height required to cut sun glare or shade an area whilst still allowing some light. Ground floor sliding windows Fixed to wall allowing access to side paths Side in fill between Veranda posts Maximum Sizes Width: up to 3,500mm Drop: up to 2,70mm Maximum Area: 7.2 m 2 Standard Components Painted aluminium side channels 5 sided painted bottom bar Top tube universal mounting brackets are mounted on wall Hood is NOT standard Valance is not standard Options to Specify 3 piece painted Overroll style hood Installation Guide Reveal fit only recommended Page No. 24

Product Details WINDSOR- Traditional Automatic Guide Awning Application Ground floor sliding windows or partial opening hinged windows Minimal distance away from wall allowing access to side paths Not suitable in high wind areas Maximum Sizes Width: up to 4,000mm Drop: up to 2,400 Maximum Area: 7.2 m 2 Standard Components Zinc plated guide rods 900, 1200, 1500, 1800, 2100, 2400 & 2700 Zinc plated arms -150, 300, 450, 600, 750 & 900 std lengths 5 sided painted bottom bar 3 piece painted steel Overroll style hood 150mm Fabric valance straight or scalloped Top tube mounting brackets are mounted inside hood end plates Operation Manual operation only Boat hook to pull bottom bar Caution handling spring action. Installation Guide Face fit only Mount 150mm (2 bricks) above window Page No. 25

Product Details RICHMOND - Maxishade Auto Guide Awning Application Ground floor sliding windows or partial opening hinged windows Minimal distance away from wall allowing access to side paths Arms may be positioned on the face of the front bar enabling guide rods & arms to be fixed on window frame or clad wall stud. Maximum Sizes Width: up to 4,000mm Drop: up to 2,400 Maximum Area: 7.2 m 2 Standard Components Zinc plated guide rods 900, 1200, 1500, 1800, 2100, 2400 & 2700 Painted aluminium arms -150, 300, 450, 600, 750 & 900 std lengths 5 sided painted bottom bar 150mm Fabric valance straight or scalloped 3 piece painted steel Overroll style hood Operation Manual operation only Boat hook to pull bottom bar Caution handling spring action. Installation Guide Face fit only Mount 150mm (2 bricks) above window. Use headboard if intermediate fixing centres reqd. Page No. 26

Awnings Overview Product Overview & Operation Options Manual or Motorised Guided Straight Drop Awnings Operation Options Product Family Not Guided Straight Drop Awnings Side Guided Pivot Arm Awnings Folding Arm Awnings Manual Operation Manual Operation (Spring Locking Bottom Bar) Narooma Mornington Open Style Full Cassette Style Manual or Motorised Stainless Steel Wire Guided Bottom Bar Oberon Bundanoon Open Style Full Cassette Style Channel Guided Bottom Bar Page No. 27

Product Details NAROOMA - Open Wire Guided S/Steel Straight Drop Manual Gear Box or Motorised Operation Application Shade external windows & balconies VG for westerly aspects Enclose outdoor living areas Maximum Sizes Width; 5,400 Drop; 3,000 Standard Components Stainless steel wire guides & brackets Manual gear box - Top roll operation Aluminium tear drop profile bottom bar up to 5,400mm wide Acrylic block out or Sunscreen fabric Options to Specify RTS motor with or without sun & wind sensors Face fix, timber floor fix or masonry floor fix brackets Installation Face Fit or Recess Fit Page No. 28

Product Details MORNINGTON - Full Cassette Wire Guided Straight Drop Manual Gear Box or Motorised Operation Application External window shades Balconies for alfresco living Sizes Width; 4,000 (95mm head box) to 5,400 (125mm head box) Drop; 2,200 (95mm head box) to 3,000 (125mm head box) Standard Components 125mm deep powder coat painted aluminium cassette head box Stainless steel wire guides & brackets Manual gear box - Top roll operation Aluminium tear drop profile bottom bar Options to Specify RTS motor with or without sun & wind sensors Acrylic block out or sunscreen fabric Installation Face Fit or Recess Fit Page No. 29

Wire Guided Straight Drop Bottom Wire Guide Bracket Options Wire Guide Face Fix Bracket Wire Guide Timber Floor Fix Bracket Wire Guide Masonry Floor Fix Bracket Note: M8 Dynaset Masonry Anchor not supplied by JPM Page No. 30

Product Details OBERON Open Style Channel Guided Straight Drop Manual Gear Box or Motorised Operation Detail showing bottom bar with end cap inside guide channel Application Shade external windows & balconies VG for westerly aspects Enclose outdoor living areas Maximum Sizes Width; 5,400 Drop; 3,000 Standard Components Manual gear box - Top roll operation Aluminium tear drop profile bottom bar up to 5,000mm wide Acrylic block out or Sunscreen fabric Options to Specify Open Overroll style painted steel hood RTS motor with or without sun & wind sensors Installation Face Fit or Recess Fit Page No. 31

Product Details BUNDANOON - Full Cassette Channel Guided Straight Drop Manual Gear Box or Motorised Operation Application External window shades Balconies for alfresco living Sizes Width; 4,000 (90mm head box) to 5,400 (125mm head box) Drop; 2,200 (90mm head box) to 3,000 (125mm head box) Standard Components 125mm deep powder coat painted aluminium cassette head box Aluminium guide tracks powder coat painted Manual gear box - Top roll operation Aluminium tear drop profile bottom bar Options to Specify RTS motor with or without sun & wind sensors Acrylic block out or sunscreen fabric Installation Face Fit or Recess Fit Page No. 32

Awnings Overview Product Overview & Operation Options Operation Options Product Family Not Guided Straight Drop Awnings Side Guided Pivot Arm Awnings Folding Arm Awnings Manual Operation Manual Operation (Spring Locking Bottom Bar) Manual or Motorised Brunswick Pivot Arm (Tape & Reel Operation) Page No. 33

Product Details BRUNSWICK - Pivot Arm Awning Flexible awning to shade windows on homes that are more than 2 stories to allow for a more consistent visual aesthetics. Maximum Sizes Width: 4,000 Drop: 2,700 Standard Components Spring loaded aluminium tube arms - tension fabric in windy areas 5 sided painted bottom bar 3 piece painted steel Overroll style hood Options to Specify Acrylic block out or Sunscreen mesh fabric 150mm Fabric valance straight or scalloped Internal or external manual 9mm wide tape cord lock (maximum 2.9m 2 ) Internal or external 14mm wide tape winch RTS motor & with or without sun/wind sensor Installation Mount 150mm (2 bricks) above window Fixed end brackets only. Use headboard if intermediate fixing centres reqd. Page No. 34

BRUNSWICK - Pivot Arm Awning Lifting Tape Options Page No. 35

Awnings Overview Product Overview & Operation Options Operation Options Product Family Not Guided Straight Drop Awnings Side Guided Pivot Arm Awnings Folding Arm Awnings Manual Operation Manual Operation (Spring Locking Bottom Bar) Bundeena Standard (Open) Folding Arm Manual or Motorised Avalon Full Cassette Folding Arm Page No. 36

Product Details JPM Folding Arm Awning Range EN13561 awning for outdoor usage. Tested to wind class 2 (max wind speed 35kph) JPM Awnings - Tested to European Standard EN 13561, for Wind Resistance Bundeena Open Folding Arm Awning, with Optional Powder Coat Painted Aluminium Hood Avalon Full Cassette Folding Arm Awning, with Full Powder Coat Painted Cassette Page No. 37

JPM Folding Arm Awnings CE Load Tested to European Standard EN 13561 for Wind Resistance EN13561 awning for outdoor usage. Tested to wind class 2 (max wind speed 35kph) Page No. 38

Product Details Bundeena Open Folding Arm Awning Hood Top fix & hood fix brackets Face fix brackets (no hood) The Bundeena is an economical & versatile awning for commercial and domestic use. Maximum Sizes Width 6,000 mm Projections 3,000 mm Standard Components 1,500, 2,000, 2,500 & 3,000mm folding arms Folding arms with twin galvanized steel cables. Exposed cables at the elbow joint are PVC covered Frame standard colours are white, ivory or grey Tilting arm bracket can be adjusted from 0 to 45 deg by an installer using special tools. Manual crank operation up to 6,000mm wide maximum Options to Specify RTS only Motor control with or without wind sensor Acrylic fabric in JPM stock colours Aluminium hood (with top fix brackets) in matching powder coat paint Eave brackets purchased locally Fascia fit brackets & fascia fit flashing purchased locally Installation Face, eave or fascia fix Page No. 39

Product Details Avalon Full Cassette Folding Arm Awning Maximum Sizes Width 6,000 mm Projections 3,000 mm Standard Components 1,500, 2,000, 2,500 & 3,000mm folding arms Folding arms with twin galvanized steel cables. Exposed cables at the elbow joint are PVC covered Frame standard colours are white, ivory or grey Tilting arm bracket can be adjusted from 0 to 50 deg by an installer using special tools. Manual crank operation up to 6,000mm wide maximum Options to Specify RTS only Motor control with or without wind sensor Acrylic fabric in JPM stock colours Installation Face fit recommended using 136mm wide brackets. The wall support brackets should be placed near the folding arms, as close as possible or the cassette may twist & not fully close If fascia or head fix installation care must be taken to minimise cassette twisting. Install brackets each side of each arm bracket to Page No. 40

Awning Specification Data Min/Max Sizes & Measuring Guidelines The Total Width Measured including side guards The fabric is always less wide than the width of the awning indicated The Drop Measured from the rear side of the roller tube to the front side of the front rail An assembled system always protrudes a little further from the wall than the drop indicated For optimal sun shading an awning must protrude sufficiently past the window to the left & right Sizes Bundeena Avalon Minimum Width - Motorised Drop + 430mm Drop + 310mm Minimum Width - Manual Drop + 450mm Drop + 330mm Maximum Width - 1 part with 2 arms 6,000mm 6,000mm Minimum Projection 1,500mm 1,500mm Maximum Projection 3,000mm 3,000mm Page No. 41

Sales Product Training Contents for Module SPT 20.1 Awnings 1. Overview Operation & Advantages Product Overview & Operation Options 2. Fabrics Fabric Options Important Information 3. Awning Products Released January 2012 Product Details Awning Mounting Brackets Automation 4. Measuring Guidelines 5. Guidelines for Safe Awning Use 6. Common Problems, Causes & Solutions 7. Summary 8. Knowledge & Learning Assessment Test 9. Appendix Page No. 42

Product Details Bundeena Open Folding Arm Awning Brackets Face Fix & Top Fix/Face Fix with Hood Brackets Important Installation Note 115mm Projection The wall support brackets should be placed near the folding arms, as close 128.5mm 215mm 96mm Projection as possible or the cassette may twist & not close evenly For fascia or head fix installation install brackets each side of each arm bracket 80.5mm Projection Face Fit (with NO Hood) Bracket 43mm wide Head Fix & Face Fix (WITH Hood) Bracket 48mm wide Check Top Tube fabric support cradle is placed under the double fabric seam, in the middle of the awning Awning Width Min. No. of Support Brackets (Instal Close to Arm Brackets) Face Mount on Wall Fascia or Head Fix Mount to Roof Trusses Top Tube Fabric Support Cradle 2,000-3,500mm 2 3 0 3,501-4,500mm 3 5 0 4,501-5,000mm 4 5 1 5,001-6,000mm 5 5 1 Page No. 43

Product Details Avalon Full Cassette Folding Arm Awning Brackets Avalon Awning Support Bracket Pitch Adjustment 0 to 50 deg 136mm Wide Face Fit Bracket Top Tube Support Cradle (factory fitted) Important Installation Note The wall support brackets should be placed near the folding arms, as close as possible or the cassette may twist & not fully close For fascia or head fix installation install brackets each side of each arm bracket Check Top Tube fabric support cradle is placed under the double fabric seam, in the middle of the awning Awning Width Min. No. of Support Brackets (Instal Close to Arm Brackets) Face Mount on Wall Fascia or Head Fix Mount to Roof Trusses Top Tube Fabric Support Cradle 2,000-4,000mm 3 4 0 4,001-6,000mm 4 5 1 Page No. 44

Folding Arm Awning Fabricated Rafter Brackets Suitable for Harol PR Series & Bundeena Awning providing correctly located & securely installed to prevent awning from twisting Suitable for Avalon providing correctly located & securely installed to prevent awning cassette from twisting Not Suitable for Harol BX260 Full Cassette Awning Refer Folding Arm Awning Brackets Document for Detailed Bracket Dimensions Page No. 45

Folding Arm Awning Fabricated Fascia Brackets Suitable for Harol PR Series & Bundeena Awning providing brackets correctly located & securely installed Suitable for Avalon providing brackets correctly located & securely installed to prevent awning cassette from twisting Not Suitable for Harol BX260 Full Cassette Awning Adaptor bracket bolted to roof trusses for fixing PR series & Bundeena folding arm awning in front of roof gutter. Solution to mount a folding arm awning above eave to increase slope & headroom clearance under front bar when open IMPORTANT: Support brackets should be placed near the folding arm brackets, as close as possible or the cassette may twist & not fully close evenly. For fascia or head fix installation install brackets each side of each arm bracket Refer Folding Arm Awning Brackets Document for Detailed Bracket Dimensions Page No. 46

Folding Arm Awning Brackets Fabricated Spreader Brackets 130 O/S Suitable for Harol PR Series & Bundeena Awning Not Suitable for Harol BX260 or Avalon Full Cassette Awning Important For structural strength there shall be a minimum of 7 courses of bricks above the awning brackets fixed to the wall. If there are not 7 courses of brackets above the brackets install spreader brackets as shown Spreader bracket should be anchored to 3 rows of brickwork below top 7 courses. i.e. rows 8,9 & 10 below the top of the brick wall (5mm thick Galv steel) Alternatively consider using Rafter or Fascia brackets Refer Folding Arm Awning Brackets Document for Detailed Bracket Dimensions Page No. 47

Sales Product Training Contents for Module SPT 20.1 Awnings 1. Overview Operation & Advantages Product Overview & Operation Options 2. Fabrics Fabric Options Important Information 3. Awning Products Product Details Awning Mounting Brackets Automation 4. Measuring Guidelines 5. Guidelines for Safe Awning Use 6. Common Problems, Causes & Solutions 7. Summary 8. Knowledge & Learning Assessment Test 9. Appendix Page No. 48

Roller Awning Product Product Details - Automation Tube HAROL PR 210 & 220 Folding Arm Awning Motors, Brackets & Adaptors Chart <6,000mm Width HAROL PR 230 Semi Cassette Folding Arm <6,000mm Width HAROL BX Awning 260 Full Product Cassette Folding Arm <6,000mm Width Size Roller Tube 78 Dia Size Motor Adaptor Bracket 78 Dia R.T.S. JPM 45E - 50/12 50Nm 12 DH30 DL34 DZ04 78 Dia Operation Type Torque RPM Part No.s' R.T.S. JPM 45ED - 50/12 (Close Resistance Stop Function) (Close Resistance Stop Function) 50Nm 12 DH30 DL34 DZ04 Part No.s' Operation R.T.S. JPM 45ED Type- 50/12 Torque RPM 50Nm 12 (Close Resistance Stop Function) (Close Resistance Stop Function) Motor DH30 Adaptor DL34 Bracket DZ04 HAROL PR 210 & 220 Folding Arm <6,000mm BUNDEENA Width Open Style Folding Arm 78 Dia. R.T.S. JPM 45E - 50/12 50Nm 12 DH30 DL34 DZ04 HAROL PR 230 Semi Cassette Folding Arm AVALON <6,000mm Full Cassette Width Folding Arm 78 Dia. R.T.S. JPM 45ED - 50/12 (Close Resistance Stop Function) (Close Resistance Stop Function) 50Nm 12 DH30 DL34 DZ04 HAROL BX 260 Full Cassette Folding R.T.S. JPM 45ED - 50/12 78 50Nm 12 DH80 DH30 DL93 Arm BRUNSWICK <6,000mm Pivot Width Arm 63 Dia DL34 (Close Resistance R.T.S. Stop Function) (Close JPM Resistance 45E - Stop 20/15 Function) 20Nm 15 DZ04 (Modified) (Modified) BUNDEENA NAROOMA Open Open Style Style - Folding Arm 78 Dia. R.T.S. JPM 45E - 50/12 20/15 50Nm 20Nm 12 15 DH30 DL34 DZ04 Wire Guided Straight Drop AVALON MORNINGTON Full Cassette Full Cassette Folding - Arm 95/3000 - Wire Guided Straight Drop R.T.S. JPM 45ED - 50/12 78 Dia. 50Nm 12 DH80 DH30 DL93 63 (Close Resistance R.T.S. DL34 Stop Function) (Close JPM Resistance 45E - Stop 20/15 Function) 20Nm 15 DZ04 (Modified) (Modified) BRUNSWICK MORNINGTON Pivot Full Arm Cassette - DH80 DL93 63 78 Dia R.T.S. JPM 45E - 20/15 20Nm 15 125/5400 Wire Guided Straight Drop (Modified) DH30 (Modified) DL34 DZ04 NAROOMA OBERON Open Open Style Style - - Wire Channel Guided Guided Straight Straight Drop Drop MORNINGTON BUNDANOON - Full Full Cassette - 95/3000 - Channel Wire Guided Guided Straight Straight Drop Drop MORNINGTON BUNDANOON - Full Full Cassette - 125/5400 Wire Channel Guided Guided Straight Straight Drop Drop OBERON Open Style - Channel Guided Straight Drop 78 Dia R.T.S. JPM 45E - 20/15 20Nm 15 DH30 DL34 DZ04 DH80 DL93 63 Dia R.T.S. JPM 45E - 20/15 20Nm 15 (Modified) DH80 (Modified) DL93 DZ04 78 Dia R.T.S. JPM 45E - 20/15 20Nm 15 DH30 DL34 DZ04 78 Dia R.T.S. JPM 45E - 20/15 20Nm 15 DH30 DL34 DZ04 BUNDANOON - Full Cassette 95/3000 Channel Guided Straight Drop BUNDANOON - Full Cassette 125/5400 Channel Guided Straight Drop 63 Dia R.T.S. JPM 45E - 20/15 20Nm 15 DH80 DL93 DZ04 78 Dia R.T.S. JPM 45E - 20/15 20Nm 15 DH30 DL34 DZ04 1. JPM 45R motors are carried as stock at the factory and are RTS only motors Page No. 49

Product Details - Automation Sun & Wind Sensors Sun & Wind Sensor Sun & Wind Sensor 240V power connection required Radio communication to RTS motors Adjustable sun & wind sensitivity Page No. 50

Product Details - Automation Electrical Wiring & Programming Information Important Safety Note ELECTRICAL CONNECTION; Should always be carried out by an Authorised and Qualified Electrical Contractor 1. Blue = Neutral 2. Brown = Live (Direction) 3. Green/Yellow = Earth Please be aware that when programming or operating a folding arm awning motor that after continuous operation for approximately 4 minutes, a built in thermal overload switch will temporarily stop the motor & protect it from permanent damage due to overheating. The motor will resume operating after a short cooling period, approximately 20 minutes At 3 metre projection it takes 1 minute to open an awning so if the motor is operated continuously it would trip out after opening & closing twice Page No. 51

Product Details - Automation Programming Pairing Motor with Remote Page No. 52

Product Details - Automation Programming Setting Top & Bottom Limits Page No. 53

Measuring Guidelines Before Quoting, Measuring & Installing Awnings It is the responsibility of each retail organisation to establish & comply with the legal requirements for the sale and installation of awnings in each state Legal requirements currently vary from State to State We are of the understanding that harmonised National Legal Standards are under review. Page No. 55

Measuring Guidelines Important - Before Quoting & Measuring for ALL Awnings NOTE; Factory make to exact measurements on order form NO deductions are made when ordered Check for any obstructions that would interfere with the correct installation and proper operation of the awning, such as; Electrical power lines, down pipes, light fittings, opening doors, façade features, clothes lines, trees etc Stairwell or lift access if required for installation Special attention needs to be taken to assess the quality of the surface for installation. Beware of poor construction, loose brickwork, and soft or hollow wall sections. Any cladded walls should have sufficient structure behind cladding for anchoring the awning. Allow for timber batten or bracing strengthening if required. 1. Determine the width to be covered with the client. Is extra window overlap required for western sun 2. Critical dimensions to take into account & check are; a) Overall finished awning width including side end caps. a) Clearance above window lintel for awning hood & top tube to fit b) Fabric is never as wide as the measurements provided Page No. 56

Measuring Guidelines Armidale - Manual Straight Drop Veranda Awning NOTE; FACTORY WILL MAKE TO EXACT SIZES. NO DEDUCTIONS ARE TAKEN OFF DIMENSIONS ORDERED FACE FIT AWNING WIDTH Window opening size + minimum of 150mm past EACH side of window opening REVEAL FIT AWNING WIDTH Measure neat internal size of reveal at 3 width points - Top, Middle & Bottom. USE THE SHORTEST DIMENSION Reveal opening size less a minimum of 10mm for thickness of EACH bottom bar end cap. FABRIC DROP Face Fit Fabric Drop = Shortest window height dimension Reveal Fit Fabric Drop Less Min 50mm if tie down straps used Valance If yes, specify if straight or scalloped LIFT MECHANISM specify handing for lift cord External operation only Specify LEFT hand or RIGHT hand when viewed looking from the outside of the house Page No. 57

Measuring Guidelines Comboyne - Manual Straight Drop Cord & Reel Awning NOTE; FACTORY WILL MAKE TO EXACT SIZES. NO DEDUCTIONS ARE TAKEN OFF DIMENSIONS ORDERED FACE FIT AWNING WIDTH Window opening size + minimum of 150mm past EACH side of window opening NOT RECOMMENDED for REVEAL FIT There will be a large fabric light gap on rope spool side FABRIC DROP Face Fit Fabric Drop = Window height + 2 bricks Min. Valance If yes, specify if straight or scalloped LIFT MECHANISM External operation only Specify LEFT hand or RIGHT hand when viewed looking from the outside of the house Determine position to fit rope cleat on wall Rope Spool Light Gap Awning width = Bracket to Bracket Specify rope length Specify tie down straps/end cap with swinging Ds or snap hooks Page No. 58

Drop Guide Rod Length = Drop + Arm Length Measuring Guidelines Windsor & Richmond - Face Fit for Automatic Style Awnings NOTE; FACTORY WILL MAKE TO EXACT SIZES. NO DEDUCTIONS ARE TAKEN OFF DIMENSIONS ORDERED AWNING WIDTH Window opening size + minimum of 150mm past EACH side of window opening FABRIC DROP Fabric Drop = Window height + Arm Length Valance If yes, specify if straight or scalloped ARM LENGTH Specify from standard sizes - 150, 300,450, 600, 750 or 900? GUIDE ROD Window height + arm length Specify lengths 900,1200, 1500, 1800, 2100, 2400 & 2700 HOOD POSITION Mount 150mm (2 bricks) above window BOAT HOOK Specify from standard lengths Page No. 59

Drop Arm Length Measuring Guidelines Face Fit for a Pivot Arm Awning NOTE; FACTORY WILL MAKE TO EXACT SIZES. NO DEDUCTIONS ARE TAKEN OFF DIMENSIONS ORDERED AWNING WIDTH Window opening size + minimum of 150mm past EACH side of window opening FABRIC DROP Fabric Drop = Window height + Arm Length Valance If yes, specify if straight or scalloped ARM LENGTH = 50% of window height LIFT MECHANISM specify handing & type Specify LEFT hand or RIGHT hand when viewed looking from the outside of the house Manual tape lift & lock? internal or external? Manual Winch internal or external? Motorisation RTS or wired switch? Page No. 60

2,000mm Min. Height Slope Height Measuring Guidelines Folding Arm Awning Slope Guide A slope of 20 deg or more is required for optimum rain protection Do not measure the awning projection horizontally. Measure the projection at the slope that the awning will drop. NOTE; Dimension L will become smaller than the projection as pitch angle increases. L Factory set F.A.A. pitch at 12 deg Projection Check Measure Hold TAPE MEASURE at the pitch the awning will slope to determine projection required. Arm Projection Awning Slope Height 12 deg Pitch 20 deg pitch 1,500 312 513 2,000 416 684 2,500 520 855 3,000 624 1,026 3,500 728 1,197 Page No. 61

Measuring Guidelines Before Quoting & Measuring for Folding Arm Awnings No screws to undo to lift up roof cladding ROOF ACCESS If roof access is required to fit FASCIA or RAFTER brackets check the roof above or behind the awning is removable Important Note; CLIPLOK roofing cannot be removed without permanent damage to the roofing. The roofing is Clipped into position and there is no access to fixing screws for removal and replacement. Page No. 62

Measuring Guidelines Folding Arm Awnings Eave Fit NOTE; FACTORY WILL MAKE TO EXACT SIZES. NO DEDUCTIONS ARE TAKEN OFF DIMENSIONS ORDERED Rafter bracket Bolted to rafter above eave Roof Rafter brackets are used to support the awning under the roof eaves Support brackets should be placed near the folding arms, as close as possible or the cassette may twist & not fully close evenly. For fascia or head fix installation install brackets each side of each arm bracket Roof tiles are lifted back for access. The rafter bracket is bolted to the rafter so that the mounting surface sits on the eaves lining. The awning bracket is then bolted through the eave lining to the rafter bracket. Universal Awning Bracket Check measure to determine the depth of rafter bracket required; 100mm, 200mm or 300mm deep Page No. 63

Measuring Guidelines Folding Arm Awnings Fascia Fit NOTE; FACTORY WILL MAKE TO EXACT SIZES. NO DEDUCTIONS ARE TAKEN OFF DIMENSIONS ORDERED 150 x 75 Colorbond steel flashing purchase locally Gutter Roof Fascia brackets are used when the head clearance is not sufficient.. This allows the bracket to slide beside the roof rafter, which is then bolted together. Note; Access is the same as rafter bracket by sliding back roof tiles. Support brackets should be placed near the folding arms, as close as possible or the cassette may twist & not fully close evenly. For fascia or head fix installation install brackets each side of each arm bracket Fascia bracket Check Measure angle using a projector spirit level to determine fascia bracket angle required Attached to rafter through slot cut in fascia board Right angled ColorBond flashing is generally fitted over top of awning hood, back into roof gutter, to weatherproof the top and back of the awning. Page No. 64

Measuring Guidelines Flashing Options for Folding Arm Awnings Under Eave Fit for Bundeena Awnings No flashing required Face Fit Bundeena Series Awnings Silicone seal between hood & brickwork recommended in open areas Face Fit Avalon Full Cassette Awnings Not generally required Facia Mount Bundeena Awnings 100 x 75 Colorbond Steel angle from top of hood to inside of roof gutter. Protect open back of awning & fabric from exposure to weather. Prevent rain from dripping between gutter & awning Optional extra Purchase locally Note; Flashing is an optional extra item & should only be supplied if included on the order Page No. 65

Measuring Guidelines Fixings for Window & Straight Drop Awnings Recommended General Galvanised Steel Screw Fixing for Window Awnings & Straight Drop Awnings 12 gauge(5mm dia. approx) x 50mm long Hex Screws Hexagonal head provides positive grip to drive screw into timber or a masonry anchor Page No. 66

Measuring Guidelines Folding Arm Awning Masonry Installation Chemset 101 Injection Anchoring Adhesive Page No. 67

Measuring Guidelines Folding Arm Awning Masonry Installation Chemset Anchor Studs Detail Use torque wrench to tighten to 40Nm (DO NOT OVER TIGHTEN) Important Follow hole cleaning instructions before injecting adhesive Page No. 68

Awnings Product Manual Contents for Module s 1. Overview Operation & Advantages Product Overview & Operation Options 2. Fabrics Fabric Options Important Information 3. Awning Products Product Details Awning Mounting Brackets Automation 4. Measuring Guidelines 5. Guidelines for Safe Awning Use 6. Common Problems, Causes & Solutions 7. Summary 8. Knowledge & Learning Assessment Test 9. Appendix Page No. 69

Guidelines for Safe Awning Use Folding Arm Awnings To ensure the longest possible life, with minimum maintenance, we recommend following simple rules:- The awning is not recommended as a rain or wind awning. DO NOT leave an awning out unattended, if no responsible person is home to bring the awning in if the weather changes, or in blustery or, high winds, or if storms are approaching. If awning controls are connected to a Wind Sensor be aware that a wind sensor will not provide full protection against sudden gusts of winds. It is possible, after a Wind Sensor is activated, & sends a signal for the awning to close, for the awning to suffer damage, during the time it takes to close. To drain properly, fabric awnings must have a minimum 20 degree slope. If the slope is less, water pockets or ponding may occur when it is raining and care should be taken to avoid damage to the frame. CLOSE THE AWNING in wet weather even if the fabric is wet. Only open the awning to dry the fabric when the weather improves. Page No. 70

Sales Product Training Contents for Module SPT 20.1 Awnings 1. Overview Operation & Advantages Product Overview & Operation Options 2. Fabrics Fabric Options Important Information 3. Current Awning Products Product Details Awning Mounting Brackets Automation 4. Measuring Guidelines 5. Guidelines for Safe Awning Use 6. Common Problems, Causes & Solutions 7. Summary 8. Knowledge & Learning Assessment Test 9. Appendix Page No. 71

Common Problems, Causes & Solutions Problem Possible Cause Possible Solution Fascia brackets are to small to mount Full Cassette Folding Arm Awning Full Cassette Folding Arm Awning is only suitable for face mount because brackets are 300 to 500mm wide For fascia & eave mount we should offer & quote Open Awnings The bottom bar of a 4 metre wide Straight Drop Wire Guide Awning is bending excessively & the fabric is wavering Straight Drop Verandah (rope & pulley) awning is too large to fit in a reveal fit Installer cannot fit Rafter Brackets to mount a Folding Arm Awnings as there are no visible screws to lift the steel roofing to gain access. Straight Drop Awning with a Sunscreen mesh has a vertical seam down the middle ruining the customers view. Awning has been ordered with a standard 20mm diameter stainless steel tube bottom bar Bottom bar end caps overhang the fabric by approximately 10mm each end. Steel CLIPLOCK roofing cannot be removed without destroying the roofing Awning is probably wider than 2.5metres & fabric has been made from 2 pieces with a seam in the middle. Specify the bigger section Aluminium Tear Drop profile bottom bar Allow clearance for end caps when check measuring width on order. ORDER SIZES ARE FACTORY MAKE SIZES Important to check the type of roofing at the time of quoting as rafter & fascia brackets cannot be fitted if the roofing is CLIPLOCK. At the time of quoting you need specify if seams are acceptable or if you have quoted a 2 x 2 mesh fabric RAILROADED so there are no seams Page No. 72

Summary Reviewed CSIRO data - Exterior window awnings can save up to 40% more of cooling energy cost than internal blinds only Folding Arm Awnings are an ideal solution for alfresco living to provide protection from the sun, shade & ambience Fabric range available Product overview & operation options 1. Straight Drop Awnings Manual Not Guided 2. Straight Drop Awnings - Manual Side Guided Awnings, with Spring Locking Bottom Bar 3. Straight Drop Awnings - Manual & Motorised Wire & Channel Guided Straight Bottom Bar 4. Pivot Arm Awnings - Manual & Motorised 5. Folding Arm Awnings Manual & Motorised. Open,& Full Cassette models 6. Folding Arm Awning - Mounting brackets 7. Automation RTS motors, sun & wind sensors Measuring guidelines order sizes are make sizes, consider straight drop light gaps, pivot arm awning arm lengths, position of sunscreen fabric seams, Clip Lock roofing cannot be removed to fit F.A.A. rafter & fascia brackets. Guidelines for safe use of awnings. Particularly use & care of folding arm awnings, especially in southerly wind changes Common problems & causes Page No. 74

Sales Product Training Contents for Module SPT 20.1 Awnings 1. Overview Operation & Advantages Product Overview & Operation Options 2. Fabrics Fabric Options Important Information 3. Awning Products Product Details Awning Mounting Brackets Automation 4. Measuring Guidelines 5. Guidelines for Safe Awning Use 6. Common Problems, Causes & Solutions 7. Summary 8. Knowledge & Learning Assessment Test 9. Appendix Page No. 75

JPM Order Forms Folding Arm Awnings - with Pull Down Menus Page No. 77

JPM Order Forms Window Awnings - with Pull Down Menus Page No. 78

JPM Order Forms Straight Drop Awnings - with Pull Down Menus Page No. 79