Technical data Folding arm awning BX260 art.nr. 34850
Inhoudsopgave 1. Generalities page 4 2. The profiles page 4 3. Other components page 5 4. Mimimum and maximum sizes page 10 5. Coupled awnings page 10 6. Weight page 11 7. Operation page 11 8. Fabrics page 11 9. Measuring and assembly page 12 10. Accessories page 13 11. Delivery page 13 12. Use and maintenance page 13 13. Security page 13 14. TÜV-label page 13 Annex : Drawings page 14 Order form folding arm awning BX260 page 16 Harol reserves the right to make alterations of the product without prior notice. 3
1. Generalities - The BX260 is a folding arm cassette awning of the compact-high type - The construction is characterised by a torque bar to which the arms, the supports and the roller tube are hooked in or pushed in - Colour of the aluminium parts and profiles : as a standard in the chosen colour of the awning (see colour card) 2. The profiles 2.1. The torque bar - Function: the other components are attached to this supporting profile 2.2. The fabric roll - Material: a round welded zendzimir tube manufactured from a zinc-plated zendzimir strip - Function: the rolling up and down of the fabric - Provided with a slot for the attachment of the fabric - Diameter: Ø78 x 1mm 2.3. The Clip On-Clip Off profile - Material: extruded PVC clips - Function: the fastening of the fabric to the fabric roll without the use of screws - Because of this system it is easy to subsequently replace the fabric Fig. 1 : Clip On - Clip Off profile Fig. 2 : Exploded view BX260 4
2.4. The top board 155 - Function: covers the fabric over the whole width - At the front provided with a toucher profile to which the extension pole closes 2.5. The extension pole - Function: closing off the awning at the front - Provided with: - at the upper side: - provided with a groove for the attachment of the fabric - at the lower side: - provided with a groove for the attachment of a valance - At the ends finished with aluminium covers: - coated in the colour of the extension pole 222 2.6. Fabric roller centre support Fig. 3 : Section BX260 - Colour: standard in the chosen colour of the awning (see colour card) - Function: - supporting the rolled up fabric - protecting the fabric at the lower side - Is attached, screwless, to the torque bar - On the inside provided with a hard PVC profile: - better guidance of the fabric - increases the life of the fabric 3. The other components Fig. 4 : Extension pole BX260 3.1. The folding arms - Connect the box and the extension pole - Available with the following drops: 1500-2000 - 2500-3000 - 3500 mm. - Up to a width of 6000 mm two arms are mounted, from 6001 mm up to 7000 mm 3 arms are mounted - The arm profiles: - The hinges: - Material: of a high pressure cast aluminium alloy - Colour: coated in the chosen colour of the awning (see colour card) - Hinge on durable slide bearings of sintered bronze, provided with a PTFE sliding layer - The most heavily loaded parts are also thermally treated - The springs and the steel cables: - Material: of high quality spring steel which has been zinc-plated beforehand - The diameter is always in relation to the force applied 5
- The power of both springs is transferred via a wedge to two zinc-plated steel cables: - ensure a division of the power - considerable extension of the operating life. 3.2. The angular displacement system - Function: - connecting the folding arms and the torque bar - makes the setting of the angle possible - The range for the angle is 10 to 35 - The system also ensures complete protection against the flapping and dropping of the arms. 3.3. Extension pole regulation Fig. 5 : Angular displacement system BX260 - Function: After the setting of the angle of drop, the extension pole is positioned by the extension pole regulation 3.4. The fastening supports - To fix the screen to the base surface required, a number of special fastening supports are available: - Wall supports: - Is used for normal assembly against a wall Fig. 6 : Extension pole regulation BX260 - Width: 300 mm or 500 mm, depending on the width of the awning, and provided with fastening holes with slot (1000 mm for coupling) - At the front provided with hooks, to hook the awning in - The exact position of the wall supports is indicated in the table position of the wall supports. - The wall support should be placed in the middle, behind the angular displacement - The number of wall supports supplied always depends on the screen width - Additional supports are deliverable (optional) - In case of an unstable foundation, it is recommended to place additional supports, in order to spread the weight of the awning over several points - At the bottom of the support, a space is provided to push in a locking bolt (the number of these bolts depend on the width of the supports) - Ceiling bracket and roof truss: not available Fig. 7 : Wall support BX260 Width 2000-4000 mm 4001-6000 mm 6001-7000 mm 7001-8000 mm 8001-12000 mm Number and type of support Number of locking bolts 2 x 300 mm 2 x 500 mm 1 x 300 mm Table 1 : Number of supports and locking bolts 3 x 500 mm 2 x 300 mm 1 x 1000 mm 2 x 300 mm 2 x 500 mm 1 x 1000 mm 4 6 6 8 12 6
Width Position of the wall supports BX260 (in mm) Distance X Width of the support (Side) Distance Y Width of the support (interm.) 2000-4000 200 300 - - 4001-6000 Width / 2 300 300 500 6001-7000 See table 500 X and Y = distance side of cassette to middle of support Position of the intermediate bracket with 3 arms* BX260 (in mm) Width / Extension 1500 2000 2500 3000 3500 6001-6099 2913 2913 2886 2386 2072 6100-6199 2962 2962 2962 2485 2122 6200-6299 3012 3012 3012 2585 2172 6300-6399 3062 3062 3062 2685 2222 6400-6499 3112 3112 3112 2785 2285 6500-6599 3162 3162 3162 2885 2385 6600-6699 3212 3212 3212 2985 2485 6700-6799 3262 3262 3262 3085 2585 6800-6899 3312 3312 3312 3185 2685 6900-6999 3362 3362 3362 3285 2785 7000 3412 3412 3412 3385 2885 * for left arm, measured from the left; for right arm, measured from the right Table 2 : Position of the wall- and intermediate brackets with 3 arms Total width B = finished width, covering plates included 50 50 X X Y Example : What is the position of the brackets for an awning of 3850 mm? Fig. 8 : Position of the wall supports We choose the corresponding width (2000-4000 mm) and take the value that corresponds with the table Distance X. The centre line of the support is at 200 mm from the side. 7
3.5. The toucher of the box - Function: - is positioned on regular distances on the torque bar, at the sides and in the middle of the awning - this is the basic support to which a bearing support can be mounted - at the front provided with a funnel-shaped space, which makes that the extension pole always closes identically (see point 3.10 entrance of the extension pole) - is also used with the fabric split covering (see point 5.4) 3.6. The bearing supports - Function: bearing the fabric roller at the sides and at coupling height of the awning - Should always be mounted on a toucher of the box Fig. 9 : Toucher of the box with bearing support 3.7. The finishing sheets of the box - Material: cast aluminium, powder coated - Function: - lateral enclosure of the awning - The side guards are attached to the sides of the box 3.8. The side guards of the box - Material: cast aluminium, powder coated - Function: - Aesthetic finishing of the finishing sheets - The side guards are mounted to the finishing sheets 3.9. The covers of the extension pole Fig. 10 : Toucher of the box with entrance - Material: cast aluminium, powder coated - Function: the finishing of the extension pole 3.10. Entrance of the extension pole - Material: synthetic PA66 - Colour: black - Function: provided with an rounded part, which makes that the extension pole always closes identically. This part hooks into the toucher of the box (see point 3.5) 3.11. Fastening material - The folding-arm awnings produce a lot of pressure on the mounting surface. Therefore it s recommended to mount the awnings with chemical anchors (company Hilti, Würth,) or other mounting systems. Fig. 11 : Finishing sheet with side guard 8
4. Minimum and maximum sizes - Width: - Maximum: - 6m in 1 part with 2 arms - 7m in 1 part with 3 arms - 12m in 2 parts with 4 arms - Minimum: - depending on the chosen drop - (electric: Bmin = drop + 500mm) - (crank: Bmin = drop + 520 mm) - for coupled awnings : see point 5 - Drop: - Maximum: 3,5m - Minimum: 1,5m 5. Coupled awnings 5.1. Coupling with cardan - The two parts are joined together, at roller tube height, by means of two with glass fibre reinforced nylon discs - Extension pole, cover and torque bar are joined together by means of coupling devices - The fabric is provided as two separate fabrics and already fitted to both awnings - Bmin (per part) = drop + 500mm 5.2. Coupling with cardan and fabric split covering Fig. 12 : Coupling device extension pole - Same as coupling with cardan (see 5.2.) - A fabric split covering subsequently seals the split between the two fabrics - Bmin (per part) = drop + 750mm 5.3. Fabric split covering - A spring axle is positioned under the fabrics at split height. - The spring axle is fixed to two transparent synthetic supports. - The fabric is fixed to the axle with a double-sided adhesive strip. - On the front side the fabric slides into the fabric slit of the end profile. - The width of the fabric split is covering 50 cm. - During the unrolling of the awning, the extension pole carries the fabric and unrolls the fabric from the spring axle. This accordingly seals the split. Fig. 13 : Coupling devices Fig. 14 : Fabric split covering 9
6. Weight - Approximate weight: ± 14 kg per metre (width) 7. Operation - Two operating types: - Crank handle operation - Motor operation - Crank handle: - As standard: - self-braking worm wheel - with transmission capacity of 7:1 - a laying hook of 160 cm is supplied - the maximum width for crank handle operation is 6000mm - Option: - longer laying hook - Motor operation - As standard: - an asynchronous built-in tube motor with adjusting buttons - motor with automatic post-regulation, the awning will always close completely - 3 metre electric cable - single-pole surface mounted switch and plug - Option: - 5 or 10 metre cable - without switch and plug - motor with remote control (RTS): - 3 metre cable, - 10 metre cable at option - with transmitter, - without transmitter (option) - For more possibilities and automation: see the Harol domotics map. Remark: the motor is already adjusted in the fabric 8. Fabrics Acrylic: - Construction: acrylic fibres, coloured in the mass - Colour: patterns and colours chosen from the standard collection - Weight: +- 290-300 g/m² - Thickness: +- 0,5mm - Confection: - vertical rows of 1200mm - side hems of 50mm - double step stitch with polyester thread - Mould-resistant and dirt-repelling 10
9. Measuring and assembly of an awning 9.1. Guidelines for the correct measuring of the awning Technical data folding arm awning BX260 - The total width: - measured including side guards Total width - the fabric is always less wide than the width of the awning indicated - The drop: - measured from the rear side of the roller tube to the Fig. 15 : Total width front side of the front rail - an assembled system always protrudes a little further from the wall than the drop indicated - For optimal sun shading an awning must protrude sufficiently past the window to the left and right 9.2. Assembly - Pay attention to the quality of the surface for assembly: - With poor walls, gas concrete, soft or hollow stone walls: - adapted fastening accessories are required - additional wall brackets are to be used - Take account of the fact that the awning must be mounted at a sufficient height (min. 2500mm) - The slope should be adjusted to an angle between 10 and 35 - account of sufficient run-out height must be taken A = extension B B A = extension A mm B mm 1500 260 2000 347 2500 434 3000 521 3500 608 A mm B mm 1500 860 2000 1147 2500 1434 3000 1721 3500 2008 Fig. 16 : Minimal and maximal adjustment 11
10. Accessories 10.1. Valance - At option - Choice between four types - Standard height 250 mm, other heights available 10.2. Side flaps Fig. 17 : Valances 1 3 2 4 - At option - The side flaps are fitted between the housing and the extension pole at the R side of the awning - The side flaps are available in two standardised forms or according to a drawing - This can only be done when the awning is fully open Fig. 18 : Side flaps 10.4. Lettering G - the fabric, valance and/or side flap can be provided with lettering (as an option) - The flounce height with lettering is 300 mm as standard - Ten diverse letter types are available - Special letter types and logos or drawings can be provided on request at extra cost Attention: Texts on striped fabrics and flounces are often difficult to read. In this case uni-fabrics are best used 11. Delivery - The awning is delivered without fastening material - To prevent damage during transportation all awnings are provided with extra protection in the form of plastic foil and fully packed in strong cardboard 12. Use and maintenance - Suitable use and maintenance greatly increase the life of the awning. - do not use the awning as a rain or wind awning - Regular maintenance of the awning prevents unnecessary wear - cleaning the frame: with soft water instead of aggressive substances, which may affect the coatings and protective layers - clean the fabric: - with a stiff brush - stubborn stains are best removed with a tepid water and brown soap solution (rinse thoroughly with copious amounts of clean water) - Let the awning dry fully before rolling it up (even after an unforeseen rain shower) Fig. 19 : Lettering 12
13. Security For security reasons (injuries) it is recommended to mount the awning according to the rules 14. TÜV-Label The TÜV-GS security label is requested. 13
Wall support 25 300, 500 of 1000 * midden 25 20 27,5 14 185 115,5 * with wall support of 300 mm : no holes with slot in the middle 14
Order form side flaps for BX260 DATE: REFERENCE : Name: Address: CLIENT / INVOICE Naam: Address: DELIVERY ADDRESS Client NR: VAT: Tel: Fax: Tel: Fax: Delivery time: B G FABRIC COLOUR SIDE (LEFT / RIGHT / LEFT+RIGHT) A B C D E F G POSITION NUMBER FINISHING 1 L / R / L+R A D 2 L / R / L+R F E C A = top of the box to the ground B = back of the box against the wall, to the front of the extension pole C = bottom of extension pole to the ground D = back of the side flap against the wall, to the front of the side flap E = bottom of side flap to the ground F = back to front at the bottom of the side flap G = top to bottom at the front of the side flap Ring and tourniquet: standard positions (see drawing) or remarks on the sketch R G S Finishing: sketch to be completed as desired - The side flaps are always seen from the outside. - Please indicate all sizes in mm. - Each order is executed according to our terms and conditions of sale. PRICE: REMARKS: I have taken note of the technical product descriptions and take full responsability for the indications and sizes mentioned. The client, V1-10-03
1. Number: Number of identical awnings 2. Coupling code: see page 9 A Simple awning, 2 arms B Simple awning, 3 arms D Coupled awning with cardan E Coupled awning with fabric split covering 3. Finished measures: Width = finished width of the box in mm Extension : see fig. 16 page 11 4. Operation: Remark : seen from the outside a. Type : 31 handle 51 electric (= standard motor) 1076 motor Orea RTS Motors : possibilities : see table in the front of the price list b. Side : 1 left 2 right 5. Standard switch / wall transmitter If not, please make your choice in the domotics list 6. Fabric colour: Please indicate colour numbers according to the collection. Order form folding arm awning BX260 7. Frame colour: 14. Letter colour: White RAL 9016 Brown RAL 8019 RAL-colour (indicate the number) Please indicate the desired colour. 15. Position of the lettering: Remark : RAL-colour for an extra 8. Valance type: see fig. 17 page 12 9. Valance height: Standard : 250 mm With lettering : 300 mm Remark : higher valance for an extra Please describe very clearly the position of the text on the fabric, the valance or the lateral fabric. For example: The position regarding to the bottom side. The position regarding to the left side. Add, when necessary, a model to the order form (please indicate this on the order form) Remark : It is for your own importance to describe very clearly the lettering. Failures caused to vague orders will not be taken at expence of Harol. 10. Supplements: A2524 extra wall support 30cm A2525 extra wall support 50cm A2526 extra wall support 100cm A2533 Wall support in metre width A2510 with fastening material A214 band for valance in non-standard colour 11. Text of lettering: Please indicate the text in capitals and/or in small letters. In case of insufficient space, please add a separate sheet, and mention this on the order form. 12. Size of lettering: Please indicate width and height of text. Attention : The colour of the fabric (background). The readability of the letter type (capitals and small letters with BRS and COS). 13. Letter type: see fig. 19 page 12
Order form folding arm awning BX260 DATE: REFERENCE : Name: Address: CLIENT / INVOICE Naam: Address: DELIVERY ADDRESS Client NR: VAT: Tel: Fax: Tel: Fax: Delivery time: FINISHED MEASURES (MM) OPERATION STANDARD FABRIC FRAME SWITCH / WALL WIDTH 1 WIDTH 2 EXTENSION TYPE SIDE TRANSMITTER COLOUR COLOUR TYPE NR VALANCE SUPPLEMENTS REFE- RENCE POSITION NUMBER COUPLING CODE FABRIC COLOUR HEIGHT 1 yes / no 2 yes / no 3 yes / no 1 2 3 4 5 6 7 8 6 9 10 POSITION NUMBER ARTICLE NR NUMBER ARTICLE NR NUMBER ARTICLE NR NUMBER ARTICLE NR NUMBER ARTICLE NR 1 DOMOTICS 2 3 MEASURES LETTER LETTER TEXT OF LETTERING POSITION OF THE LETTERING WIDTH HEIGTH TYPE COLOUR DRAWING INCLUDED Text : yes / no 11 12 13 14 15 - The operation is always seen from the outside. - Please indicate all sizes in mm. - Each order is executed according to our terms and conditions of sale. PRICE: REMARKS: I have taken note of the technical product descriptions and take full responsability for the indications and sizes mentioned. The client,