FEBRUARY, 2015 1 DOOR STILE Device C L 40" 41-9/32" Cylinder C L Bottom of door RIM EXIT DEVICE LOCATION DOGGING KEY EXIT DEVICE FILLER PLATE CYLINDER & CYLINDER RING HOUSING COVER CYLINDER INSTALLATION Cylinder must be installed before exit device. Insert cylinder with cylinder ring into the door stile and secure in place with cylinder mounting screws. CYLINDER MOUNTING SCREWS CYLINDER RING CYLINDER INSTALLING CYLINDERS BY OTHERS Cut tailpiece to correct length and install. (Mounting screw heads must be flush with door surface.) 2-1/16" Cylinder mounting screws must be flush
2 FEBRUARY, 2015 OPTIONAL TRIM 1786 RIM EXIT DEVICE LEVER HANDLE TRIM ASSEMBLY/: 1) Trim mounting base is handed to accommodate a left or right handle application. To construct a left hand (LH) lever handle, rotate cam clockwise making sure the cam pin aligns with slot on left side of cam guide. (See Illustration below) Once the pin is in position, slightly push up and hold cam guide and cam while inserting lever handle firmly into place within the trim mounting base. The tail piece will now be oriented in the vertical position. 2) To construct a right hand (RH) lever handle, rotate cam counter clockwise making sure the cam pin aligns with slot on right side of cam guide. (See Illustration below) Once the pin is in position, slightly push up and hold cam guide and cam while inserting lever handle firmly into place within the trim mounting base. The tail piece will now be oriented in the vertical position. 3) Assemble (1) 1/4" -20 x 1/2" Phillips pan head fastener with (1) steel flat washer and (1) lock washer to secure lever handle to trim mounting base. 4) Insert 15/16" key cylinder (dummy cylinder on inactive door leaf) into top hole of trim mounting base. Align mounting guide plate to key cylinder and secure with retaining ring. 5) When using a key cylinder longer than 15/16", cylinder rings will be required to maintain a 1/8" cylinder projection. When using a dummy cylinder on inactive door leafs, place the lock arm switch in a lock position to disable the lever handle function. 6) Before installation of trim mounting base, cut break-away tail piece to the correct length. (see illustration)ation. 7) Find (1) 1/4"-20 x 3/4" Phillips pan head fastener and apply several drops of thread locker liquid to lower threads. Install Phillips pan head fastener into trim mounting base and set to accommodate a 1/8" (Standard/Thermal door) or 3/16" (Heavy Wall) wall thickness. (Fastener may require additional adjustment to ensure that trim mounting base is fully secured into position.) 8) On exterior side of door stile, position lever handle trim assemble into cutout, just below the fastener slot cutout. Being careful not to scratch the exposed finish surface, slide lever handle trim assemble up to engage fastener into slot. 9) On interior side of door stile, install (1) fastener (see below) through door to secure lever handle trim assembly in position. (1) #10-24 x 2 1/4" FHMS for Standard 1-3/4" doors (1) #10-24 x 2-1/2" FHMS for Heavy Wall 2" doors (1) #10-24 x 2-3/4" FHMS for Thermal 2-1/4" doors 10) Lever handle trim assemble should be tightly secured to ensure that hardware is placed square upon door stile and cannot be moved. 11) Upon completion, insert cylinder key and turn clockwise to unlock, then counter- clockwise to lock. 12) Install rim exit device. 1786 RIM EXIT DEVICE TRIM HANDING GUIDE: Lever Handle (Shown LH Single Active Pair) Lever Handle (Shown RH Single Inactive Pair) Cam Tail Piece (Vertically) Cam Lift Pin Left Slot Lock Arm Switch Cam Guide Lock Arm Switch Cam Tail Piece (Horizontally) Cam Lift Pin Right Slot Cam Guide Lever (LH) Lever (RH) Push Up and Hold Cam Guide Push Up and Hold Cam Guide
FEBRUARY, 2015 3 Trim mounting base Cylinder retaining ring Mounting guide plate 15/16" cylinder with 0.800" cam Non. Wall Thickness 1/8" or 3/16" 15/16" Threadlocker 1/4"-20 x 3/4" PPHS Note: See Step #7 1/8" Cylinder Projection 1/4"-20 x 1/2" PPHS Steel flat washer & lock washer Lever handle (Shown as LH) Fastener slot cut-out 1/4"-20 x 3/4" PPHS 0.800" Cam Sweep Lock Arm Switch 1-7/8" 2-1/8" 2-3/8" Break-away tail piece 190/350/500 Standard Door (1-3/4") [with 2-1/4" fastener] 350/500 Heavy Wall Door (2") [with 2-1/2" fastener] AA250/AA425 Thermal Door (2-1/4") [with 2-3/4" fastener] #10-24 PFHMS
4 EXIT DEVICE WITH PUSH PAD DOGGING FEBRUARY, 2015 TO DOG EXIT DEVICE Insert the hex key and turn clockwise until it stops. Fully depress touch bar and release the key. With touch bar retracted remove hex key. TO UNDOG EXIT DEVICE Push on touch bar. Insert hex key and turn clockwise until it stops. Release touch bar, when the touch bar is in the extended position release hex key and remove. RIM EXIT DEVICE ATTACHMENT (Push Pad Dogging or Cylinder Dogging) 1) Undog exit device. 2) Install exit device onto door stiles as indicated below. 3) Attach exit device to pivot stile with mounting bracket and fastener provided. END CAP MOUNTING BRACKET PIVOT STILE ATTACHMENT FASTENER 4) Attach exit device to lock stile with fasteners provided. DOGGING KEY LOCK STILE #12-24 ATTACHMENT FASTENERS
FEBRUARY, 2015 EXIT DEVICE WITH CYLINDER DOGGING 5 1) Install pivot stile filler plate into exit device. 2) Install cylinder as pictured, making sure cylinder is tight against filler plate. MAKE SURE CYLINDER IS ORIENTED AS PICTURED 3) Tighten set screw in dogging mechanism with a phillips head screw driver, through hole in end of base bracket. DO NOT OVER TIGHTEN SET SCREW
6 FEBRUARY, 2015 FINAL ASSEMBLY 1) Slide pivot stile filler plate into exit device and attach pivot stile end cap with fasteners provided. (Filler plate with cylinder dogging has been installed previously) 2) Slide lock stile filler plate into exit device. 3) Install housing cover brackets onto top and bottom of exit device with fasteners provided. 4) Install housing cover over brackets and attach with (Black) fasteners provided. END CAP FASTENERS (Black) END CAP PIVOT STILE FILLER PLATE HOUSING COVER BRACKET & FASTENER LOCK STILE FILLER PLATE HOUSING COVER HOUSING COVER FASTENERS (Black) STRIKE INSTALLATION AND ADJUSTMENT 1) Prep door jamb for strike as shown below. FIN TO BE MILLED FLUSH WITH FACE OF MULLION 0.750 0.375 0.128 DIA. (4 PLS) 0.312 0.812 TRIFAB 450 SHOWN TRIFAB 451 SIMILAR 3.580 0.938 1.875 0.438 0.149 Ø THRU HOLE TAP FOR #10-24 UNF-2B (2) PLACES 0.438 40.000 + BTM DOOR CLEARANCE (40.687 W/ STD 11/16" CLEARANCE) C L 2) Attach strike to door jamb with fasteners provided. 3) Close door and adjust strike as required to hold door tight against weathering. 4) Attach stainless steel rub plate with (4) 1/8" drive rivets provided. ADJUST STRIKE AS REQUIRED NOTE: Rub plate for 1-3/4" door (133643) included with exit device. Rub plate for 2" and 2-1/4" door (133644) BOTTOM order separately. LEFT HAND SHOWN RIGHT HAND OPPOSITE
FEBRUARY, 2015 7 5 7 18 2 1 17 16 7 15 13 14 13 12 4 3 6 9 10 11 WITH PUSH BAR DOGGING PARTS BREAKDOWN 8 RIM EXIT DEVICE PACKAGE TO INCLUDE: EXIT DEVICE ITEM # QTY DESCRIPTION 1 1 EA. EXIT DEVICE BASE ASSEMBLY (SIZED ACCORDING TO PART NUMBER) 2 1 EA. HINGE/PIVOT FILLER PLATE (SIZED ACCORDING TO PART NUMBER) 3 1 EA. LATCH FILLER PLATE 4 1 EA. # 12-24 PANIC ATTTACHMENT FASTENER 5 1 EA. "S" STRIKE PACKAGE WITH FASTENERS AND LOCK BLOCK (133-588) 6 1 EA. METAL HOUSING COVER (BLACK MATT FINISH) 7 4 EA. HOUSING COVER ATTACHMENT FASTENERS (BLACK) 8 1 EA. HINGE/PIVOT STILE ATTACHMENT FASTENER 9 1 EA. END CAP MOUNTING BRACKET 10 1 EA. HINGE/PIVOT END CAP (BLACK MATT FINISH) 11 2 EA. END CAP FASTENERS (BLACK) 12 1 EA. DOGGING KEY 13 2 EA. PUSH PAD END CAPS (BLACK MATT FINISH) 14 1 EA. PUSH PAD ASSEMBLY 15 2 EA. HOUSING COVER BRACKET 16 2 EA. HOUSING COVER BRACKET FASTENERS 17 1 EA. RUB PLATE 18 4 EA. 1/8" DRIVE RIVET INDICATES PART TO BE IN COLOR TO BLEND WITH THE DOOR FINISH KAWNEER FINISH MANUFACTURER FINISH TOUCHBAR RIM EXIT DEVICE 17 CLEAR 40 BRONZE US28/628 DBZ 313 133580 3'-0" NON HANDED 133581 3'-6" NON HANDED 133582 4'-0" NON HANDED
8 FEBRUARY, 2015 15 16 9 10 18 2 1 17 12 7 8 14 13 NOTE: EXIT DEVICE WILL INCLUDE (1) STANDARD KAWNEER 15/16" CYLINDER WITH (2) KEYS. 13 4 5 7 3 6 WITH CYLINDER DOGGING PARTS BREAKDOWN 11 RIM EXIT DEVICE PACKAGE TO INCLUDE: EXIT DEVICE ITEM # QTY DESCRIPTION 1 1 EA. EXIT DEVICE BASE ASSEMBLY (SIZED ACCORDING TO PART NUMBER) 2 1 EA. HINGE/PIVOT FILLER PLATE (SIZED ACCORDING TO PART NUMBER) 3 1 EA. LATCH FILLER PLATE 4 1 EA. # 12-24 PANIC ATTACHMENT FASTENER 5 1 EA. "S" STRIKE PACKAGE WITH FASTENERS AND LOCK BLOCK (133588) 6 1 EA. METAL HOUSING COVER (BLACK MATT FINISH) 7 4 EA. HOUSING COVER ATTACHMENT FASTENERS (BLACK) 8 1 EA. HINGE/PIVOT STILE ATTACHMENT FASTENER 9 1 EA. END CAP MOUNTING BRACKET 10 1 EA. HINGE/PIVOT END CAP (BLACK MATT FINISH) 11 2 EA. END CAP FASTENERS (BLACK) 12 1 EA. CYLINDER WITH (2) KEYS INCLUDES CYLINDER DOGGING KIT 13 2 EA. PUSH PAD END CAPS (BLACK MATT FINISH) 14 1 EA. PUSH PAD ASSEMBLY 15 2 EA. HOUSING COVER BRACKET 16 2 EA. HOUSING COVER BRACKET FASTENERS 17 1 EA. RUB PLATE 18 4 EA. 1/8" DRIVE RIVET INDICATES PART TO BE IN COLOR TO BLEND WITH THE DOOR FINISH KAWNEER FINISH MANUFACTURER FINISH TOUCHBAR RIM EXIT DEVICE 17 CLEAR 40 BRONZE US28/628 DBZ 313 133580CD 3'-0" NON HANDED 133581CD 3'-6" NON HANDED 133582CD 4'-0" NON HANDED
FEBRUARY, 2015 9 4 133586 STANDARD HEIGHT (7'0" DO or 82-7/16" PART) 133587 VARIABLE HEIGHT TO (8'0" DO or 94-7/16" PART) 5 6 REMOVABLE MULLION PACKAGE TO INCLUDE: 7 1 2 3 EXIT DEVICE ITEM # QTY DESCRIPTION 1 1 EA. VERTICAL MULLION (SIZED ACCORDING TO PART NUMBER) 2 2 EA. SHOE MULLION 3 2 EA. BACK PLATE FOR SHOE MULLION 4 1 EA. SHOE MULLION MOUNTING PLATE 5 4 EA. #14 x 1-1/2" FHTF - FASTENERS FOR UPPER SHOE MOUNTING PLATE TO HEAD 6 2 EA. 1/4-20 x 7/8" OHMS - BACK PLATE ATTACHMENT FASTENERS 7 4 EA. 1/4-20 x 3/4" FHMS - FASTENERS FOR UPPER SHOE TO PLATE 8 4 EA. 1/4-20 x 1-1/8" FHMS W/ANCHORS - FASTENERS FOR LOWER SHOE TO FLOOR 9 2 EA. MULLION STABILIZERS 10 2 EA. DOOR STABILIZERS 11 4 EA. STABILIZER SHIMS 12 8 EA. #10-24 x 7/8" OHMS - FASTENERS FOR MULLION STABILIZERS INDICATES PART TO BE IN COLOR TO BLEND WITH THE DOOR FINISH MULLION STABILIZER PREP NOTE: STABILIZERS SHIPPED WITH MULLION MULLION STABILIZER PACKAGE 10 9 11 KAWNEER FINISH MANUFACTURER FINISH 8 12 17 CLEAR US28/628 40 BRONZE DBZ 313 6 3 2 82-7/16" FOR STOCK 7'0" DOOR OPNG (94-7/16" VARIABLE HEIGHT DOOR OPNG) CUT SIZE = DO - 1.5625 40 11/16" UNIT W/THRESHOLD C L OF STRIKE
10 FEBRUARY, 2015 REMOVABLE MULLION HEADER/T-BAR PREP 1) Prep Header/T-Bar as shown below. 400020 400079 450020 450079 451020 451079 2.500 1.000 0.562 C L PART AND OPERATION 0.656 1.125 1.312 1.375 0.281 Ø THRU HOLE (2) PLACES 0.201 Ø (#7 DRILL) THRU HOLE FOR #14 SELF TAPPING SCREW (4) PLACES REMOVE DOOR STOP FIN MUST BE FLUSH TO MAXIMIM OF 0.010 DEEP (NO RAISED BURRS ALLOWED) 2.750 1.000 REMOVABLE MULLION THRESHOLD PREP 1) Field notch threshold as shown below. 1.312 0.662 1.155 R0.336 C L PART AND OPERATION 069139 069143
FEBRUARY, 2015 REMOVABLE MULLION INSTALLATION 11 "A" SECTION "A-A" (TOP SHOE MULLION) "A" ATTACH SHOE MULLION MOUNTING PLATE TO T-BAR ATTACH SHOE MULLION TO MOUNTING PLATE (SHOWN DASHED) 7/8" 1) Attach shoe mullion mounting plate to header/t-bar as shown. 2) Attach top shoe mullion to mounting plate on header/t-bar as shown. 3) Secure bottom shoe mullion to floor as shown. 4) Check removable mullion for correct length from bottom of mullion to centerline of strike. a) Cut mullion to proper overall length if required. 5) Slip removable mullion into top shoe mullion, pick up and swing onto bottom shoe mullion. 6) Install back plate onto shoe mullion at header/t-bar and threshold. (See Figure #1) SHOE MULLION MOUNTING PLATE (SEE SECTION "A-A") 1/4" SHOE MULLION BACK PLATE FOR SHOE MULLION AT HEADER/T-BAR BACK PLATE FOR SHOE MULLION AT THRESHOLD MULLION STABILIZER SHOE MULLION FRAME OPENING MINUS 1-9/16" (WITH OR WITHOUT THRESHOLD) 11/16" WITHOUT THRESHOLD C/L OF DOOR OPENING EXTERIOR 11/16" 40" TO BOTTOM OF DOOR "B" WITH THRESHOLD FIGURE #1 "B" 1-5/32" 5/8" 1" LINE OF DOOR STOP 1-1/2" 7/16" 1-5/16" 21/32" PREP FOR 1/4-20 X 1-1/8" FHMS 3/8" W/ 1/4-20 FLOOR ANCHOR SECTION "B-B" (BOTTOM SHOE MULLION) 1-1/8"
12 FEBRUARY, 2015 MULLION STABILIZER INSTALLATION 1) Attach frame portion stabilizers in holes provided on mullion with 2 ea. #10-24 x 7/8" O.H.M.S. 2) Close door and align door portion on the door, allowing 1/16" for clearance, as shown. 3) Mark hole centers, drill and tap for #10-24 in door. 4) Attach door portion stabilizers to door with 2 ea. #10-24 x 7/8" O.H.M.S. FRAME PORTION STABILIZER DOOR PORTION STABILIZER 1/16" REMOVABLE MULLION #10-24 X 7/8" O.H.M.S.
FEBRUARY, 2015 13 THIS PAGE LEFT INTENTIONALLY BLANK
14 FEBRUARY, 2015 Kawneer Company, Inc. Technology Park/Atlanta 555 Guthridge Court Norcross, GA 30092-3503