Round Die Products www.anchorlamina.com Check our website for the latest technical information. 1

BUSHINGS General Information Bushings... 2 & 3 STANDARD SHOULDER BUSHINGS Bronze Plated & Solid Steel... 4 Solid Bronze & Self-Lubricating... 5 Pressed Fit... 6 Bushings for Lifter Pin Metric... 6 Long & Extra Long Shoulder Bushings... 7 SHORT SHOULDER BUSHINGS Bronze Plated... 8 Solid Bronze... 9 Self-Lubricating... 10 METRIC BUSHINGS NAAMS... 11 & 12 Standard Shoulder Bushings Metric... 13 Long & Extra Long Shoulder Bushings Metric... 14 Short Shoulder Bushings Metric... 15 TECHNICAL INFORMATION Toe Clamp Selection... 16 Toe Clamp Placement... 17 Bore Sizes for Pins & Bushings... 18 GUIDE PINS, continued Guide Pins Tap Fit (Demountable)... 28 & 29 Guide Pins Shoulder Inch... 30 Metric... 31 Guide Pins Removable... 32 Stripper Guide Pins & Bushings... 34 & 35 STOCK LIFTERS 75 Stock Lifters... 36 112 Stock Lifters... 37 75 Rail Lifters... 38 112 Rail Lifters... 39 Mini Lifters... 40 Repair Parts... 41 Metric Lifter Pins... 42 Stop Blocks... 43 PAD RETAINERS Pad Retainers, Standard Inch... 44 Pad Retainers, Reverse Mount Inch... 45 Pad Retainers, Standard & Reverse Metric.. 46 Spool Type Pad Retainers Metric... 47 MISCELLANEOUS BUSHINGS Running Fit Bushings Hardened... 19 Running Fit Bushings Soft... 20 Guide Bar Bushings (Wiper Bushings)... 21 Precision Bearings... 21 GUIDE PINS General Information Pins... 22 Straight Guide Pins TN & ATN... 23 Straight Guide Pins TPB... 24 Straight Guide Pins TPC... 25 Straight Guide Pins NAAMS... 26 Straight Guide Pins Hollow... 26 Straight Guide Pins TN Metric... 27 Straight Guide Pins TPB Metric... 27 Short SC-GSC SCB-GSCB SHOULDER BUSHING STYLES Standard AC-GAC ACB-GACB Long LAC-GLAC Extra-Long XLAC-GXLAC All bronze plated shoulder bushings must be wring-fit in the die shoe. It is also recommended that Solid Bronze shoulder bushings be mounted similarly. Bronze plated bushings feature fi gure 8 oil grooves for maximum lubrication. For long wear, bronze plated bushings should be lubricated with a high temperature, high pressure lithium grease on a regular basis. Self-lubricating bronze with graphite bushings require initial lubrication with light oil. Periodic lubrication will extend the life of self-lubricating bushings. Do not use grease. 2

Specials have become very important at Lamina. The table below will give a basic idea of our everyday manufacturing capabilities. If you have a need for special bushings, please send your requests for quotations. See page 22 for pin manufacturing capabilities. BUSHING MANUFACTURING CAPABILITIES Straight & Shoulder Bronze Plated & Solid Steel Solid Bronze Self- Lubricating Series Inch Min. Length Max. Length Series Metric Min. Length Max. Length.750 1 2.0 32 25 150 1.000 1 3.0 40 25 150 1.250 1 6.0 50 25 350 1.500 1 6.0 63 25 350 1.750 1 10.0 80 25 350 2.000 1 14.0 100 25 350 2.500 1 14.0 125 25 350 3.000 1 14.0.625 1 2.0.750 1 3.0 19 25 100.875 1 4.0 1.000 1 5.0 1.250 1 7.0 1.500 1 7.0 1.750 1 7.0 40 25 150 2.000 1 9.0 50 25 225 2.500 1 9.0 63 25 225 3.000 1 9.0 80 25 225 3.750 1 9.0 100 25 225 4.500 1 9.0 125 25 225.5000 0.375 5.0.625 0.375 5.87 12.5 9 50.750 0.375 5.87.875 0.375 5.87 20 9 140 1.000 0.375 5.87 1.250 1 6.0 1.500 1 6.0 1.750 1 6.0 40 9 150 2.000 1 6.0 2.500 1.25 8.0 3.000 1.25 8.0 3.750 2 16.0 4.500 2 16.0 100 50 400.625 0.375 3.5 12.50 9 50.750 0.875 6.0 19 9 140.875 0.875 6.0 20 9 140 1.000 0.875 6.0 1.250 0.875 6.0 1.500 0.875 6.0 1.750 0.875 6.0 2.000 1.25 6.0 2.500 1.25 8.0 63 25 200 3.000 1.25 8.0 3.750 1.25 8.0 4.500 1.25 8.0 125 50 200 We are not restricted to the above parameters. Every quote will be analyzed for manufacturing possibility. LAMINA DIE SET STANDARD GRIND (LDSS) Tapers.0005 Nominal Wring Fit Diameter Slight taper on wring fit diameter facilitates installation. (This feature is standard on all bronze plated and solid steel shoulder bushings unless otherwise noted.) Bushings are held in place with toe clamps and screws unless otherwise noted. In the following pages bronze plated and solid steel bushings which are listed as ground are LDSS ground. GUIDE BUSHINGS Class 1 & 2 bushing dimensions shown opposite are for use in precision die sets. Class 3 bushings are for use with automotive, hardware, forming or draw dies where stamping stock is thicker than 1/16, and clearances between punch and die sections will be more than.003 per side. Bronze-Plated Bushings Available in Class 1 or Class 2 Solid Bronze Bushings Available in Class 1 or Class 2 Hardened Steel Bushings available in Class 2 Self-Lubricating Bushings available in Class 3 NOMINAL PIN DIAMETER 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/2 3 LAMINA BUSHINGS I.D. Dimensions Class 1 Class 2 Class 3.7503.7502.8753.8752 1.0003 1.0002 1.2503 1.2502 1.5003 1.5002 1.7503 1.7502 2.0003 2.0002 2.5006 2.5004 3.0008 3.0006 3-3/4 4-1/2.7506.7503.8756.8753 1.0006 1.0003 1.2506 1.2503 1.5006 1.5003 1.7506 1.7503 2.0007 2.0003 2.5012 2.5006 3.0014 3.0008 3.7518 3.7510 4.5025 4.5015.7510.7506.8760.8756 1.0010 1.0006 1.2510 1.2506 1.5010 1.5006 1.7512 1.7507 2.0012 2.0007 2.5018 2.5012 3.0023 3.0014 3.7528 3.7518 4.5035 4.5025 3

Bushings Inch Wring Fit Style D4 D2 L3.187 BRONZE PLATED SOLID STEEL *See page 3 for details. See pages 16 & 17 for toe clamp installation instructions. C L Grease Fitting (incl.) Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/8-3 - 1/8-27 NPTF, 7/16 hex.75 D5 D3 L4.188 D-Clamps & Screws are included with wring fi t style bushings. STANDARD SHOULDER BUSHINGS BRONZE PLATED D2 D3 D4 D5 L3 L4 NOM WRING FIT Class 2* Class 1* HEAD SHOULDER HEAD OVERALL WRING HEAD DIAMETER PIN OD OD OD FIT GROUND UNGROUND GROUND UNGROUND DIA GROUND UNGROUND GROOVE GAC-750-S AC-750-S GAC7501S AC7501S 3/4 1.1250 1.140 1.219 1.313 1.125 2.063.813 1.250 GAC-875-S AC-875-S GAC8751S AC8751S 7/8 1.3750 1.390 1.469 1.563 1.375 2.125.875 1.250 GAC-100-S AC-100-S GAC1001S AC1001S 2.125.875 1 1.5000 1.515 1.656 1.750 1.563 GAC-100-L AC-100-L GAC1001L AC1001L 3.125 1.875 1.250 GAC-125-S AC-125-S GAC1251S AC1251S 2.625 1.125 1-1/4 1.7500 1.765 2.031 2.125 1.938 GAC-125-L AC-125-L GAC1251L AC1251S 3.625 2.125 1.500 GAC-150-SP 2.650 1.150 GAC-150-S AC-150-S GAC1501S AC1501S 1-1/2 2.0000 2.281 2.375 2.188 2.875 1.375 1.500 2.015 GAC-150-L AC-150-L GAC1501L AC1501L 3.875 2.375 GAC-175-SP 2.875 1.375 GAC-175-S AC-175-S GAC1751S AC1751S 1-3/4 2.2500 2.531 2.625 2.438 3.125 1.625 1.500 2.265 GAC-175-L AC-175-L GAC1751L AC1751L 4.125 2.625 GAC-200-SP 2.875 1.375 GAC-200-S AC-200-S GAC2001S AC2001S 2 2.5000 3.031 3.125 2.938 3.375 1.875 1.500 2.515 GAC-200-L AC-200-L GAC2001L AC2001L 4.375 2.875 GAC-250-S AC-250-S GAC2501S AC2501S 2-1/2 3.0000 3.015 3.531 3.625 3.438 3.875 1.875 2.000 GAC-300-S AC-300-S GAC3001S AC3001S 3 3.6250 3.640 4.281 4.375 4.188 3.875 1.875 2.000 STANDARD SHOULDER BUSHINGS SOLID STEEL D2 D3 D4 D5 L3 L4 Class 2 only* NOMINAL WRING FITDIAMETER HEAD WRING HEAD SHOULDER OVERALL HEAD PIN OD FIT GROUND UNGROUND OD OD DIAMETER GROUND UNGROUND GROOVE GAC-750-SS AC-750-SS 3/4 1.1250 1.140 1.219 1.313 1.125 2.063.813 1.250 GAC-100-SS AC-100-SS 2.125.875 1.250 1 1.5000 1.515 1.656 1.750 1.563 GAC-100-SS2 AC-100-SS2 2.875.875 2.000 GAC-125-SS AC-125-SS 2.625 1.125 1.500 1-1/4 1.7500 1.765 2.031 2.125 1.938 GAC-125-SS2 AC-125-SS2 3.125 1.125 2.000 GAC-150-SS AC-150-SS 2.875 1.375 1.500 1-1/2 2.0000 2.015 2.281 2.375 2.188 GAC-150-SS2 AC-150-SS2 3.375 1.375 2.000 GAC-175-SS AC-175-SS 3.125 1.625 1.500 1-3/4 2.2500 2.265 2.531 2.625 2.438 GAC-175-SS2 AC-175-SS2 3.625 1.625 2.000 GAC-200-SS AC-200-SS 3.375 1.875 1.500 2 2.5000 2.515 3.031 3.125 2.938 GAC-200-SS2 AC-200-SS2 3.875 1.875 2.000 GAC-250-SS AC-250-SS 2-1/2 3.0000 3.015 3.531 3.625 3.438 3.875 1.875 2.000 4

Bushings Inch Wring Fit Style D4 D2 L3.187.75 L4.188 SOLID BRONZE SELF-LUBRICATING *See page 3 for details. See pages 16 & 17 for toe clamp installation instructions. Grease Fitting (Solid Bronze only) Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/8-1/8-27 NPTF, 7/16 hex D5 D3 D-Clamps & Screws are included with wring fi t style bushings. STANDARD SHOULDER BUSHINGS SOLID BRONZE D2 NOM WRING FIT D3 D4 D5 L3 L4 Class 2* Class 1* SHOUL- HEAD OVER- WRING PIN DIAMETER HEAD HEAD DER OD ALL FIT OD GROUND UNGROUND GROUND UNGROUND DIA GROUND UNGROUND OD GROOVE GAC-750-SB AC-750-SB GAC7501SB AC7501SB 3/4 1.1250 1.140 1.219 1.313 1.125 2.063.813 1.250 GAC-875-SB AC-875-SB GAC8751SB AC8751SB 7/8 1.3750 1.390 1.469 1.563 1.375 2.125.875 1.250 GAC-100-SB AC-100-SB GAC1001SB AC1001SB 1 1.5000 1.515 1.656 1.750 1.563 2.125.875 1.250 GAC-125-SB AC-125-SB GAC1251SB AC1251SB 1-1/4 1.7500 1.765 2.031 2.125 1.938 2.625 1.125 1.500 GAC-150-SB AC-150-SB GAC1501SB AC1501SB 1-1/2 2.0000 2.015 2.281 2.375 2.188 2.875 1.375 1.500 GAC-175-SB AC-175-SB GAC1751SB AC1751SB 1-3/4 2.2500 2.265 2.531 2.625 2.438 3.125 1.625 1.500 GAC-200-SB AC-200-SB GAC2001SB AC2001SB 2 2.5000 2.515 3.031 3.125 2.938 3.375 1.875 1.500 GAC-250-SB AC-250-SB GAC2501SB AC2501SB 2-1/2 3.0000 3.015 3.531 3.625 3.438 3.875 1.875 2.000 GAC-300-SB AC-300-SB GAC3001SB AC3001SB 3 3.6250 3.640 4.281 4.375 4.188 3.875 1.875 2.000 Class 3 only* STANDARD SHOULDER BUSHINGS SELF LUBRICATING NOMINAL PIN DIAMETER D2 WRING FIT DIAMETER Note: Self-lubricating bronze with graphite bushings require initial lubrication with light oil. Periodic lubrication will extend the life of self-lubricating bushings. Do not use grease. D3 HEAD OD D4 SHOULDER OD D5 HEAD OD GROOVE OVERALL L3 WRING FIT L4 HEAD GROUND UNGROUND GROUND UNGROUND GACB750S ACB750S 3/4 1.1250 1.140 1.219 1.313 1.125 2.063.813 1.250 GACB100S ACB100S 1 1.5000 1.515 1.656 1.750 1.563 2.125.875 1.250 GACB125S ACB125S 1-1/4 1.7500 1.765 2.031 2.125 1.938 2.625 1.125 1.500 GACB150S ACB150S 1-1/2 2.0000 2.015 2.281 2.375 2.188 2.875 1.375 1.500 GACB175S ACB175S 1-3/4 2.2500 2.265 2.531 2.625 2.438 3.125 1.625 1.500 GACB200S ACB200S 2 2.5000 2.515 3.031 3.125 2.938 3.375 1.875 1.500 GACB250S ACB250S 2-1/2 3.0000 3.015 3.531 3.625 3.438 3.875 1.875 2.000 GACB300S ACB300S 3 3.6250 3.640 4.281 4.375 4.188 3.875 1.875 2.000 All Standard Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with toe clamps and screws. This means that the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see bore size information on page 18. 5

Bushings Inch Pressed Fit Style Press Fit Shoulder Bushings allow for fast, easy installation. Eliminates the use of clamps and screws. D2 L3 Grease Fittings 3/4-1/4-28 NTF, 5/16 hex 7/8-1/8-27 NPTF, 7/16 hex.750 L4 BRONZE PLATED Figure 8 oil grooves allow the lubricant to fl ow smoothly throughout the bushing I.D. Grease Fitting D3 NOMINAL PIN DIAMETER 8-1188-2500 1 10-1188-2688 1-1/4 12-1438-2938 1-1/2 SHOULDER BUSHING PRESS FIT * 1.0006 1.0003 1.2506 1.2503 1.5007 1.5004 D2 PRESS FIT DIAMETER 1.5023 1.5018 1.7523 1.7518 2.0023 2.0018 D3 HEAD O.D. OVERALL L4 HEAD L3 PRESS FIT 1.688 2.500 1.313 1.188 1.938 2.688 1.500 1.188 2.188 2.938 1.500 1.438 Recommended Bore Size 1.5005 1.5000 1.7505 1.7500 2.0005 2.0000 *Please note! Press Fit bushings have tapered holes, larger at press fit end. This facilitates honing, since the bore will close up in a more nearly straight line when pressed in. While these bushings are precision fi nished on the O.D. a small amount of stock is left on the I.D. to allow for honing because they are pressed fi t type. Toe clamps and screws are not provided with press fi t shoulder bushings and they do not come with an LDSS grind. BUSHINGS FOR LIFTER PINS METRIC D2 D2 MBL-704530 30 MBL-704540 45 55 40 MBL-704550 50 6

Bushings Wring Fit Style D4 D2 L3.187.188 BRONZE PLATED SOLID STEEL *See page 3 for details. See pages 16 & 17 for toe clamp placement instructions. D-Clamps & Screws are included with wring fi t style bushings. Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/8-1/8-27 NPTF, 7/16 hex.75 L4 D5 D3 Grease Fitting Class 2* Class 1* LONG SHOULDER BUSHINGS BRONZE PLATED NOM PIN DIA D2 WRING FIT DIAMETER D3 HEAD OD D4 SHOUL- DER OD D5 HEAD OD GROOVE OVER- ALL L3 WRING FIT L4 HEAD GROUND UNGROUND GROUND UNGROUND GROUND UNGROUND GLAC-750-S LAC-750-S GLAC7501S LAC7501S 3/4 1.1250 1.140 1.219 1.313 1.125 2.813.813 2.000 GLAC-875-S LAC-875-S GLAC8751S LAC8751S 7/8 1.3750 1.390 1.469 1.563 1.375 3.000.875 2.125 GLAC-100-S LAC-100-S GLAC1001S LAC1001S 1 1.5000 1.515 1.656 1.750 1.563 3.125.875 2.250 GLAC-125-S LAC-125-S GLAC1251S LAC1251S 1-1/4 1.7500 1.765 2.031 2.125 1.938 3.500 1.125 2.375 GLAC-150-S LAC-150-S GLAC1501S LAC1501S 1-1/2 2.0000 2.015 2.281 2.375 2.188 4.125 1.375 2.750 GLAC-150-SP 1-1/2 2.0000 2.015 2.281 2.375 2.188 3.900 1.150 2.750 GLAC-175-S LAC-175-S GLAC1751S LAC1751S 1-3/4 2.2500 2.265 2.531 2.625 2.438 4.625 1.625 3.000 GLAC-200-S LAC-200-S GLAC2001S LAC2001S 2 2.5000 2.515 3.031 3.125 2.938 4.625 1.625 3.000 GLAC-250-S LAC-250-S GLAC2501S LAC2501S 2-1/2 3.0000 3.015 3.531 3.625 3.438 5.375 1.875 3.500 GLAC-300-S LAC-300-S GLAC3001S LAC3001S 3 3.6250 3.640 4.281 4.375 4.188 5.875 1.875 4.000 EXTRA-LONG SHOULDER BUSHINGS BRONZE PLATED Class 2* Class 1* NOM PIN DIA D2 WRING FIT DIAMETER D3 HEAD OD D4 SHOUL- DER OD D5 HEAD OD GROOVE OVER- ALL L3 WRING FIT L4 HEAD GROUND UNGROUND GROUND UNGROUND GROUND UNGROUND GXLAC-750-S XLAC-750-S GXLAC7501S XLAC7501S 3/4 1.1250 1.140 1.219 1.313 1.125 3.563.813 2.750 GXLAC-875-S XLAC-875-S GXLAC8751S XLAC8751S 7/8 1.3750 1.390 1.469 1.563 1.375 4.375.875 3.500 GXLAC-100-S XLAC-100-S GXLAC1001S XLAC1001S 1 1.5000 1.515 1.656 1.750 1.563 4.375.875 3.500 GXLAC-125-S XLAC-125-S GXLAC1251S XLAC1251S 1-1/4 1.7500 1.765 2.031 2.125 1.938 4.625 1.125 3.500 GXLAC-150-S XLAC-150-S GXLAC1501S XLAC1501S 1-1/2 2.0000 2.015 2.281 2.375 2.188 4.875 1.375 3.500 LONG & EXTRA LONG SHOULDER BUSHINGS SOLID STEEL D2 D3 D4 D5 L3 L4 Class 2 only* NOMINAL WRING FIT DIAMETER HEAD HEAD SHOULDER OVERALL WRING FIT HEAD PIN OD GROUND UNGROUND OD OD DIAMETER GROUND UNGROUND GROOVE GXLAC-750-SS XLAC-750-SS 3/4 1.1250 1.140 1.219 1.313 1.125 3.813.813 3.000 GXLAC-100-SS XLAC-100-SS 1 1.5000 1.515 1.656 1.750 1.563 3.875.875 3.000 GXLAC-125-SS XLAC-125-SS 1-1/4 1.7500 1.765 2.031 2.125 1.938 4.125 1.125 3.000 GXLAC-150-SS XLAC-150-SS 1-1/2 2.0000 2.015 2.281 2.375 2.188 4.375 1.375 3.000 GXLAC-175-SS XLAC-175-SS 1-3/4 2.2500 2.265 2.531 2.625 2.438 4.625 1.625 3.000 GLAC-200-SS LAC-200-SS 2 2.5000 2.515 3.031 3.125 2.938 3.625 1.625 2.000 GXLAC-200-SS XLAC-200-SS 2 2.5000 2.515 3.031 3.125 2.938 4.625 1.625 3.000 GLAC-250-SS LAC-250-SS 2-1/2 3.0000 3.015 3.531 3.625 3.438 5.375 1.875 3.500 7

Bushings Inch Wring Fit Style D2 Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/8-1/8-27 NPTF, 7/16 hex L3.75.187 BRONZE PLATED *See page 3 for details. See pages 16 & 17 for toe clamp placement instructions. D-Clamps & Screws are included with wring fi t style bushings. SHORT SHOULDER BUSHINGS BRONZE PLATED D2 D3 D4 L3 NOM Class 2* Class 1* WRING FIT DIAMETER SHOUL- OVER- WRING HEAD PIN DER ALL FIT UNGROUND GROUND GROUND UNGROUND OD DIA GROUND UNGROUND OD SC-750-S GSC-750-S GSC7501S SC7501S 1.563 1.063 3/4 1.1250 1.140 1.125 1.313 SC-750-L GSC-750-L GSC7501L SC7501L 2.313 1.813 SC-875-S GSC-875-S GSC8751S SC8751S 1.563 1.063 7/8 1.3750 1.390 1.375 1.563 SC-875-L GSC-875-L GSC8751L SC8751L 2.313 1.813 SC-100-S GSC-100-S GSC1001S SC1001S 1.875 1.375 1 1.5000 1.515 1.563 1.750 SC-100-L GSC-100-L GSC1001L SC1001L 2.875 2.375 SC-125-S GSC-125-S GSC1251S SC1251S 2.375 1.875 1-1/4 1.7500 1.765 1.938 2.125 SC-125-L GSC-125-L GSC1251L SC1251L 3.375 2.875 SC-150-S GSC-150-S GSC1501S SC1501S 2.375 1.875 1-1/2 2.0000 2.015 2.188 2.375 SC-150-L GSC-150-L GSC1501L SC1501L 3.375 2.875 SC-175-S GSC-175-S GSC1751S SC1751S 2.875 2.375 1-3/4 2.2500 2.265 2.438 2.625 SC-175-L GSC-175-L GSC1751L SC1751L 3.875 3.375 SC-200-S GSC-200-S GSC2001S SC2001S 2.875 2.375 2 2.5000 2.515 2.750 2.938 SC-200-L GSC-200-L GSC2001L SC2001L 3.875 3.375 SC-250-S GSC-250-S GSC2501S SC2501S 3.000 2.625 SC-250-M GSC-250-M GSC2501M SC2501M 2-1/2 3.0000 3.015 3.188 3.375 4.000 3.625 SC-250-L GSC-250-L GSC2501L SC2501L 5.000 4.625 SC-300-S GSC-300-S GSC3001S SC3001S 4.000 3.625 SC-300-M GSC-300-M GSC3001M SC3001M 3 3.5000 3.515 3.688 3.875 5.000 4.625 SC-300-L GSC-300-L GSC3001L SC3001L 6.000 5.625 Reference on page 9. For bushing I.D.s less than 1.25, hole diameter is.188; for bushing I.D.s 1.25+, hole diameter is.344. D3 D4 L4 HEAD.500.500.500.500.500.500.500.375.375 L4 Lamina pins and bushings are used in die sets for the metal stamping industry. 8

Bushings Inch Wring Fit Style D2 Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/8-1/8-27 NPTF, 7/16 hex L3.75.187 *See page 3 for details. SOLID BRONZE See pages 16 & 17 for toe clamp placement instructions. D-Clamps & Screws are included with wring fi t style bushings. L4 D3 D4 SHORT SHOULDER BUSHINGS SOLID BRONZE D2 D3 D4 L3 L4 NOM WRING FIT HEAD SHOUL- OVER- WRING HEAD Class 2* Class 1* PIN DIAMETER OD DER ALL FIT GROUND UNGROUND GROUND UNGROUND DIA GROUND UNGROUND OD GSC-750-SB SC-750-SB GSC7501SB SC7501SB 1.563 1.063 3/4 1.1250 1.140 1.125 1.313 GSC-750-LB SC-750-LB GSC7501LB SC7501LB 2.313 1.813.500 GSC-875-SB SC-875-SB GSC8751SB SC8751SB 1.563 1.063 7/8 1.3750 1.390 1.375 1.563 GSC-875-LB SC-875-LB GSC8751LB SC8751LB 2.313 1.813.500 GSC-100-SB SC-100-SB GSC1001SB SC1001SB 1.875 1.375 1 1.5000 1.515 1.563 1.750 GSC-100-LB SC-100-LB GSC1001LB SC1001LB 2.875 2.375.500 GSC-125-SB SC-125-SB GSC1251SB SC1251SB 2.375 1.875 1-1/4 1.7500 1.765 1.938 2.125 GSC-125-LB SC-125-LB GSC1251LB SC1251LB 3.375 2.875.500 GSC-150-SB SC-150-SB GSC1501SB SC1501SB 2.375 1.875 1-1/2 2.0000 2.015 2.188 2.375 GSC-150-LB SC-150-LB GSC1501LB SC1501LB 3.375 2.875.500 GSC-175-SB SC-175-SB GSC1751SB SC1751SB 2.875 2.375 1-3/4 2.2500 2.265 2.438 2.625 GSC-175-LB SC-175-LB GSC1751LB SC1751LB 3.875 3.375.500 GSC-200-SB SC-200-SB GSC2001SB SC2001SB 2.875 2.375 2 2.5000 2.515 2.750 2.938 GSC-200-LB SC-200-LB GSC2001LB SC2001LB 3.875 3.375.500 GSC-250-SB SC-250-SB GSC2501SB SC2501SB 3.000 2.625 GSC-250-MB SC-250-MB GSC2501MB SC2501MB 2-1/2 3.0000 3.015 3.188 3.375 4.000 3.625.375 GSC-250-LB SC-250-LB GSC2501LB SC2501LB 5.000 4.625 GSC-300-SB SC-300-SB GSC3001SB SC3001SB 4.000 3.625 GSC-300-MB SC-300-MB GSC3001MB SC3001MB 3 3.5000 3.515 3.688 3.875 5.000 4.625.375 GSC-300-LB SC-300-LB GSC3001LB SC3001LB 6.000 5.625 GSC-375-B SC-375-B 3-3/4 4.5000 4.515 4.688 4.875 7.000 6.625.375 GSC-450-B SC-450-B 4-1/2 5.5000 5.515 5.688 5.875 8.000 7.625.375 Bushings of 2.50 diameter and larger have 1.25 dimensions. For bushing I.D.s less than 1.25, hole diameter is.188; for bushing I.D.s 1.25+, hole diameter is.344. All Short Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with toe clamps & screws. This means the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see bore size information on page 18. 9

Bushings Inch Wring Fit Style D2.187 L3 BRONZE with SELF-LUBRICAT- ING GRAPHITE PLUGS *See page 3 for details. See pages 16 & 17 for toe clamp placement instructions. Class 3 only* SHORT SHOULDER BUSHINGS SELF-LUBRICATING NOM PIN DIA D-Clamps & Screws are included with wring fi t style bushings. D2 WRING FIT DIAMETER GROUND UNGROUND GROUND UNGROUND D3 HEAD OD D4 SHOULDER OD OVERALL L3 WRING FIT L4 HEAD GSCB750S SCB750S 1.563 1.063 3/4 1.1250 1.1410 1.125 1.313 GSCB750L SCB750L 2.313 1.813.500 GSCB875S SCB875S 1.563 1.063 7/8 1.3750 1.3910 1.375 1.563 GSCB875L SCB875L 2.313 1.813.500 GSCB100S SCB100S 1.875 1.375 1 1.5000 1.5160 1.563 1.750 GSCB100L SCB100L 2.875 2.375.500 GSCB125S SCB125S 2.375 1.875 1-1/4 1.7500 1.7660 1.938 2.125 GSCB125L SCB125L 3.375 2.875.500 GSCB150S SCB150S 2.375 1.875 1-1/2 2.0000 2.0160 2.188 2.375 GSCB150L SCB150L 3.375 2.875.500 GSCB175S SCB175S 2.875 2.375 1-3/4 2.2500 2.2660 2.438 2.625 GSCB175L SCB175L 3.875 3.375.500 GSCB200S SCB200S 2.875 2.375 2 2.5000 2.5160 2.750 2.938 GSCB200L SCB200L 3.875 3.375.500 GSCB250S SCB250S 3.000 2.625 GSCB250M SCB250M 2-1/2 3.0000 3.0160 3.188 3.375 4.000 3.625.375 GSCB250L SCB250L 5.000 4.625 GSCB300X SCB300X 3.000 2.625 GSCB300S SCB300S 4.000 3.625 3 3.5000 3.5160 3.688 3.875 GSCB300M SCB300M 5.000 4.625.375 GSCB300L SCB300L 6.000 5.625 GSCB375S SCB375S 3-3/4 4.5000 4.5160 4.688 4.875 7.000 6.625.375 GSCB450S SCB450S 4-1/2 5.5000 5.5160 5.688 5.875 8.000 7.625.375 D3 D4 L4 Self-lubricating bronze with graphite bushings require initial lubrication with light oil. Periodic lubrication will extend the life of self-lubricating bushings. Do not use grease. 10

Bushings Metric Wring Fit Style D2 BRONZE with SELF-LUBRICATING GRAPHITE PLUGS See page 17 for toe clamp placement instructions. SHORT-SHOULDER BUSHINGS SELF-LUBRICATING - NAAMS NOMINAL PIN DIAMETER G612540 25 G613250 32 G614063 40 G615071 50 G616380 63 G618010 80 G611012 100 G611114 115 G611216 125 TOL H6 +.013 +.000 +.016 +.000 +.016 +.000 +.016 +.000 +.019 +.000 +.019 D2 WRING FIT DIAMETER 32 40 50 63 80 +.000 100 +.022 +.000 125 +.022 +.000 140 +.025 +.000 160 G720000C Clamps & Screws are included with NAAMS wring fi t style bushings. D2 Tol g6.009.025 -.009 -.025 -.009 -.025 -.010 -.029 -.010 -.029 -.012 D3 D4 D3 D4 OVERALL 6 L3 WRING FIT 32 40 40 30 40 50 50 40 50 63 63 50 63 71 71 56 80 90 80 63 -.034 100 112 100 80 -.014 -.039 125 140 125 106 -.014 -.039 140 155 140 120 -.014 -.039 160 180 160 132 L3 No. TOE CLAMPS & SCREWS 3 NOTE: Evenly distributed graphite covers 20-30% of the sliding surface. Graphite is positioned to ensure overlapping in the slide direction. See page 17 for Toe Clamp information and 18 for bore sizes. These short shoulder bushings are made especially for automotive stamping companies. They conform to the standards agreed to by the North American Automotive Metric Standards group. AUTOMOTIVE METRIC NAAMS STANDARD 11

Bushings Metric These pad bushings are made especially for automotive stamping companies. They conform to the standards agreed to by the North American Automotive Metric Standards group. D2 BRONZE with SELF LUBRICATING GRAPHITE PLUGS D4 6 See page 17 for toe clamp installation instructions. NOMINAL PIN DIAMETER G712540 25 G713250 32 G714055 40 G715063 50 G716375 63 G718090 80 G711011 100 G711213 125 SELF-LUBRICATING PAD BUSHINGS - NAAMS TOL c9 +.162 +.110 +.182 +.120 +.182 +.120 +.192 +.130 +.214 +.140 +.224 +.150 +.257 +.170 +.300 +.200 D2 WRING FIT DIAMETER 32 40 50 63 80 100 125 160 D2 TOL g6.009.025 -.009 -.025 -.009 -.025 -.010 -.029 -.010 -.029 -.012 -.034 -.014 -.039 -.014 -.039 D4 OVERALL 40 40 50 50 63 55 71 63 90 75 112 90 140 115 180 138 NOTE: Evenly distributed graphite covers 20-30% of the sliding surface. Graphite is positioned to ensure overlapping in the slide direction. AUTOMOTIVE METRIC NAAMS STANDARD See page 18 for bore size information. A full complement of flat products is also available from the Lamina Components line. 12

Bushings Metric Wring Fit Style Bronze plated shoulder bushings are available in metric sizes. D4 D2 L3 5 5 BRONZE PLATED See pages 16 & 17 for toe clamp installation instructions. (GROUND) (UNGROUND) D-Clamps & Screws are included with wring fi t style bushings. Grease Fitting All Standard Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with toe clamps and screws. This means the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see clamping information on page 16 & 17 and bore size information on page 18. 17 Grease Fittings, North America Ø18 & 19mm - 1/4-28 NTF, 5/16 hex Ø24-80mm - 1/8-27 NPTF, 7/16 hex D5 D3 STANDARD SHOULDER BUSHINGS BRONZE PLATED METRIC NOM PIN DIA GAC-18S AC-18S 18 18.011 18.005 28.000 27.995 GAC-19S AC-19S 19 19.011 19.005 28.000 27.995 GAC-24S AC-24S 24 24.011 24.005 38.000 37.992 GAC-25S AC-25S 25 25.011 25.005 38.000 37.992 GAC-30S AC-30S 30 30.014 30.008 45.000 44.992 GAC-32S AC-32S 32 32.014 32.008 45.000 44.992 GAC-40S AC-40S 40 40.014 40.008 54.000 53.992 GAC-42S AC-42S 42 42.014 42.008 54.000 53.992 GAC-50S AC-50S 50 50.014 50.008 65.000 64.992 GAC-52S AC-52S 52 52.014 52.008 65.000 64.992 GAC-63S AC-63S 63 63.016 63.010 81.000 80.990 GAC-80S AC-80S 80 80.016 80.010 100.000 99.990 *Unground wring fi t tolerance is +0.000 0.013. D2 WRING FIT DIAMETER (GROUND) (UNGROUND) D3 HEAD O.D. D4 SHOULDER O.D. +0.13 0.00 D5 HEAD OD GROOVE OVERALL +0.00 0.26 L3 WRING FIT +0.00 0.26 L4 HEAD L4 NO. CLAMPS & SCREWS 28.406 31.00 34.00 29.00 50.00 18.00 32.00 2 28.406 31.00 34.00 29.00 50.00 18.00 32.00 2 38.406 41.00 44.00 39.00 55.00 23.00 32.00 3 38.406 41.00 44.00 39.00 55.00 23.00 32.00 3 45.406 50.00 53.00 48.00 60.00 26.00 34.00 3 45.406 50.00 53.00 48.00 60.00 26.00 34.00 3 54.406 60.00 63.00 58.00 67.00 30.00 37.00 3 54.406 60.00 63.00 58.00 67.00 30.00 37.00 3 65.406 76.00 79.00 74.00 75.00 35.00 40.00 4 65.406 76.00 79.00 74.00 75.00 35.00 40.00 4 81.406 89.00 92.00 87.00 88.00 46.00 42.00 4 100.406 108.00 111.00 106.00 98.00 46.00 52.00 4 13

Bushings Metric Wring Fit Style D4 D2 L3 5 5 17 D-Clamps & Screws are included with wring fi t style bushings. L4 See pages 16 & 17 for toe clamp placement instructions. *Unground wring fi t tolerance is +0.000 0.013. Grease Fittings, North America Ø18 & 19mm - 1/4-28 NTF, 5/16 hex Ø24-80mm - 1/8-27 NPTF, 7/16 hex D5 D3 Grease Fitting LONG & EXTRA LONG SHOULDER BUSHINGS BRONZE PLATED METRIC D2 NOM WRING FIT O.D. PIN GROUND UNGROUND DIA GROUND UNGROUND GLAM-18F GLAC-18S GLAM-19F GLAC-19S GLAM-24F GLAC-24S GLAM-25F GLAC-25S GLAM-30F GLAC-30S GLAM-32F GLAC-32S GLAM-40F GLAC-40S GLAM-42F GLAC-42S GLAM-50F GLAC-50S GLAM-52F GLAC-52S GLAM-63F GLAC-63S GLAM-80F GLAC-80S LAM-18F LAC-18S LAM-19F LAC-19S LAM-24F LAC-24S LAM-25F LAC-25S LAM-30F LAC-30S LAM-32F LAC-32S LAM-40F LAC-40S LAM-42F LAC-42S LAM-50F LAC-50S LAM-52F LAC-52S LAM-63F LAC-63S LAM-80F LAC-80S 18 19 24 25 30 32 40 42 50 52 63 80 18.011 18.005 19.011 19.005 24.011 24.005 25.011 25.005 30.014 30.008 32.014 32.008 40.014 40.008 42.014 42.008 50.014 50.008 52.014 52.008 63.016 63.010 80.016 80.010 28.000 27.995 28.000 27.995 38.000 37.992 38.000 37.992 45.000 44.992 45.000 44.992 54.000 53.992 54.000 53.992 65.000 64.992 65.000 64.992 81.000 80.990 100.000 99.990 D3 HEAD O.D. D4 SHOULDER O.D. +0.13 0.00 D5 HEAD OD GROOVE 28.406 31.00 34.00 29.00 28.406 31.00 34.00 29.00 38.406 41.00 44.00 39.00 38.406 41.00 44.00 39.00 45.406 50.00 53.00 48.00 45.406 50.00 53.00 48.00 54.406 60.00 63.00 58.00 54.406 60.00 63.00 58.00 65.406 76.00 79.00 74.00 65.406 76.00 79.00 74.00 81.406 89.00 92.00 87.00 100.406 108.00 111.00 106.00 OVERALL +0.00 0.26 69.00 70.00 69.00 70.00 80.00 80.00 80.00 80.00 89.00 90.00 89.00 90.00 99.00 100.00 99.00 100.00 109.00 110.00 109.00 110.00 129.00 128.00 149.00 148.00 L3 WRING-FIT +0.00 0.26 26.00 18.00 26.00 18.00 32.00 23.00 32.00 23.00 36.00 26.00 36.00 26.00 46.00 30.00 46.00 30.00 56.00 35.00 56.00 35.00 66.00 46.00 76.00 46.00 L4 HEAD 43.00 52.00 43.00 52.00 48.00 57.00 48.00 57.00 53.00 64.00 53.00 64.00 53.00 70.00 53.00 70.00 53.00 75.00 53.00 75.00 63.00 82.00 73.00 102.00 NO. CLAMPS & SCREWS 2 2 3 3 3 3 3 3 4 4 4 4 All Standard Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with toe clamps and screws. This means that the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see clamping information on page 16 & 17 and bore size information on page 18. 14

Bushings Metric Wring Fit Style D2 Grease Fittings, North America Ø18 & 19mm - 1/4-28 NTF, 5/16 hex Ø24-80mm - 1/8-27 NPTF, 7/16 hex See pages 16 & 17 for toe clamp placement instructions. * L3 H1 SHORT SHOULDER BUSHINGS BRONZE PLATED METRIC *Ø4.76 for bushings with nom. I.D.s between 18 & 32mm. *Ø8.73 for bushings with nom. I.D.s between 40 & 80mm. D-Clamps & Screws are included with wring fi t style bushings. D2 D4 L3 H1 NOM WRING FIT DIAMETER D3 SHOULDER OVERALL WRING NO. HEAD OD FIT LUBE CLAMPS & PIN O.D. +0.13 +0.00 HOLE DIA 0.00 0.26 +0.00 SCREWS GROUND UNGROUND GROUND *UNGROUND 0.26 CENTER GSC-18S SC-18S 18 18.011 28.000 31.00 18.00 18.005 27.995 28.406 29.00 34.00 GSCL-18F SCL-18F 49.00 36.00 8.00 2 GSC-19S SC-19S 19 19.011 28.000 31.00 18.00 19.005 27.995 28.406 29.00 34.00 GSCL-19F SCL-19F 49.00 36.00 8.00 2 GSC-24S SC-24S 24 24.011 38.000 36.00 23.00 24.005 37.992 38.406 39.00 44.00 GSCL-24F SCL-24F 55.00 42.00 12.00 3 GSC-25S SC-25S 25 25.011 38.000 36.00 23.00 25.005 37.992 38.406 39.00 44.00 GSCL-25F SCL-25F 55.00 42.00 12.00 3 GSC-30S SC-30S 30 30.014 45.000 43.00 30.00 30.008 44.992 45.406 48.00 53.00 GSCL-30F SCL-30F 59.00 46.00 15.00 3 GSC-32S SC-32S 32 32.014 45.000 43.00 30.00 32.008 44.992 45.406 48.00 53.00 GSCL-32F SCL-32F 59.00 46.00 15.00 3 GSC-40S SC-40S 40 40.014 54.000 49.00 36.00 40.008 53.992 54.406 58.00 63.00 GSCL-40F SCL-40F 67.00 54.00 19.00 3 GSC-42S SC-42S 42 42.014 54.000 49.00 36.00 42.008 53.992 54.406 58.00 63.00 GSCL-42F SCL-42F 67.00 54.00 19.00 3 GSC-50S SC-50S 50 50.014 65.000 59.00 46.00 50.008 64.992 65.406 74.00 79.00 GSCL-50F SCL-50F 75.00 62.00 19.00 4 GSC-52S SC-52S 52 52.014 65.000 59.00 46.00 52.008 64.992 65.406 74.00 79.00 GSCL-52F SCL-52F 75.00 62.00 19.00 4 GSC-63S SC-63S 63 63.016 81.000 74.00 61.00 63.010 80.990 81.406 87.00 92.00 GSCL-63F SCL-63F 89.00 76.00 19.00 4 GSC-80S SC-80S 80 80.016 80.010 100.000 99.990 100.406 106.00 111.00 89.00 76.00 19.00 4 *Unground wring fi t tolerance is +0.000 0.013. 13 D3 D4 5 All Standard Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with toe clamps and screws. This means that the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see clamping information on page 16 & 17 and bore size information on page 18. 15

Toe Clamp Information for Inch & Metric Plain Bearing Die Bushings Bushing ID # Provided AC, LAC, XLAC D-Clamps SC CLAMP & SCREW PLACEMENT INCH Bolt Circle Diameter X-40 Clamps LMB AC, LAC, XLAC SC Bushing ID AC,LAM, LAC, SC METRIC Bolt Circle Diameter # Provided D-Clamps X-40 Clamps.625 2 1.531 1.644 18 2 45 47.18.750 2 1.719 1.719 1.719 1.831 1.831 1.891 19 2 45 47.18.875 2 1.969 1.969 2.081 2.081 24 3 55 57.18 1.00 3 2.156 2.156 2.156 2.269 2.269 2.269 25 3 55 57.18 1.25 3 2.531 2.531 2.531 2.644 2.644 2.644 30 3 64 66.18 1.50 3 2.781 2.781 2.781 2.894 2.894 2.894 32 3 64 66.18 1.75 3 3.031 3.031 3.031 3.144 3.144 3.144 40 3 74 76.18 2.00 4 3.531 3.344 3.344 3.644 3.456 3.456 42 3 74 76.18 2.50 4 4.031 3.781 4.031 4.174 3.894 4.174 50 4 90 92.18 3.00 6 4.781 4.281 4.531 4.944 4.424 4.694 52 4 90 92.18 3.75 6 5.281 5.281 5.281 5.281 5.424 5.444 63 4 103 105.94 4.50 6 6.281 6.281 6.281 6.281 6.444 6.444 80 4 122 125.45 LMB Toe Clamp Dimensions.563 14.30.688 17.48.278.547.266.188 7.06 13.89 6.76 4.78.367.389.328.771.188 9.32 9.88 8.33 19.58 4.78 D-Clamp & BHC031075 Screw (5/16-18 x 3/4 ) D-Clamp & F010810 Metric Screw (M8 x 1.25-20mm) X-40-Clamp & SHC031075 Screw (5/16-18 x 3/4 ) X-40-Clamp & F010810 Metric Screw (M8 x 1.25-20mm) REPLACEMENT KITS CLAMPS & SCREWS D-Clamps Nom Pin # Clamps No. of & Screws Kits Diameters per Kit Needed Nom Pin # Clamps No. of & Screws Kits Diameters per Kit Needed CSK100002 5/8-7/8 2 1 CSK10052 18-19 2 1 CSK100003 1-1-3/4 3 1 CSK10053 24-42 3 1 CSK100002 2-2-1/2 2 2 CSK10052 50-80 2 2 CSK100003 3-4-1/2 3 2 X40-Clamps CSK200002 5/8-7/8 2 1 CSK20052 18-19 2 1 CSK200003 1-1-3/4 3 1 CSK20053 24-42 3 1 CSK200002 2-2-1/2 2 2 CSK20052 50-80 2 2 CSK200003 3-4-1/2 3 2 Bolt Circle Diameter Drawing above can refer to either D-Clamps or X-40-Clamps 16

Toe Clamp Information for Inch & Metric Demountable Components NOM. PIN DIA. 1, 1 1 /4, & 1 1 /2 1 3 /4, 2, 2 1 /2 & 3 1 3 /4, 2, 2 1 /2 & 3 1 3 /4, 2, 2 1 /2 & 3 BALL-BEARING DEMOUNTABLE COMPONENT CLAMP ARRANGEMENTS 120 35 40 40 STANDARD LEFT - RIGHT FEED 55 50 35 FEED FEED FEED 45 45 FRONT to BACK FEED (Center Post Die Sets) 120 90 35 35 40 40 FEED FEED FEED FEED ROUND DIES 45 10 90 5 120 70 80 BOLT CIRCLE DIAMETERS DEMOUNTABLE BALL BEARING BUSHINGS Nominal Bolt Circle Bushing Diameter Diameter 1 2.438 1-1/4 2.813 1-1/2 3.125 1-3/4 3.438 2 4.000 2-1/2 4.500 3 5.000 DEMOUNTABLE BALL BEARING & PLAIN BEARING PINS Nominal Pin Bolt Circle Diameter Diameter 1 1.750 1-1/4 2.000 1-1/2 2.250 1-3/4 2.625 2 2.875 2-1/2 3.375 3 3.875 KEYLESS DEMOUNTABLE BALL BEARING BUSHINGS Nominal Bolt Circle Bushing Diameter Diameter 1 2.625 1-1/4 2.875 1-1/2 3.375 1-3/4 3.625 2 4.125 2-1/2 4.625 3 5.250 KEYLESS DEMOUNTABLE BALL BEARING PINS Nominal Pin Bolt Circle Diameter Diameter 1 1.625 1-1/4 1.969 1-1/2 2.250 1-3/4 2.594 2 2.884 2-1/2 3.344 3 3.844 BUSHING CLAMPING PROCEDURES AUTOMOTIVE METRIC NAAMS STANDARD 6 Clamp Part No: G720000C 24.6 18.9 13 M8 x 1.25 x 20 Long D4 (O.D. of Bushing Shoulder) B.C. = D4 + 18 (ID of Bushing) M8 x 1.25 Tap (3) Holes equally spaced D4 B.C. (D4 + 18) 25 40 58 32 50 68 40 63 81 50 71 89 63 90 108 80 112 130 100 140 158 115 155 173 125 180 198 NOTES & SPECIFICATION: Bushings will be supplied with (3) toe clamps and (3) screws - M8. Screws must engage 16mm minimum deep into die shoe. 17

18 Nom. Pin Diameter 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/2 3 GSC Only 3 3-3/4 4-1/2 18mm 19mm 24mm 25mm 30mm 32mm 40mm 42mm 50mm 52mm 63mm 80mm 100mm 115mm 125mm Standard Inch GAC GLAC GXLAC & GSC Style Bushings RECOMMENDED BORE SIZES for PLAIN BEARING PINS & BUSHINGS Standard Metric GAC,GLAC, GLAM & GSC Style Bushings Short Shoulder & Pad Bushings NAAMS DEFINITIONS OF MOUNTING PROCEDURES Pins and bushings require specific mounting procedures. By following these procedures the components should give maximum life and reduce downtime due to improper alignment, breakage and uneven wear. Pressed Fit The component is installed in an interference condition: the bore size is smaller than the pressed fi t portion of the component. Bushing Liner For Removable Pin Straight Guide Pins Inch TN & ATN Straight Guide Pins Metric TN Straight Guide Pins Inch TPC Bushings that require a pressed fi t should never be frozen or hammered. They should be forced into place using a hydraulic press or other proper tooling. Improper methods can permanently change the tolerance of the component. Pins can be forced into place using a hydraulic press; or the pins can be frozen and pressed into place. Lamina does not recommend hammering pins into place. Hammering can cause the pins to mushroom or expand on the pin Demountable Inch Guide Pins Standard Metric Guide Pins Wring Fit Wring Fit Wring Fit Pressed Fit Pressed Fit Pressed Fit Pressed Fit Pressed Fit Tap Fit Tap Fit Tap Fit 1.1255 0.7485 0.7505 1.1250 0.7480 0.7500 1.3755 0.8755 1.3750 0.8750 1.5005 1.4988 0.9985 1.0005 1.0005 1.5000 1.4983 0.9980 1.0000 1.0000 1.7505 1.7488 1.2480 1.2505 1.2505 1.7500 1.7483 1.2475 1.2500 1.2500 2.0005 1.9983 1.4980 1.5005 1.5005 2.0000 1.9978 1.4975 1.5000 1.5000 2.2505 2.2483 1.7480 1.7505 1.7505 2.2500 2.2478 1.7475 1.7500 1.7500 2.5005 2.4983 1.9975 2.0000 2.0005 2.5000 2.4978 1.9970 1.9995 2.0000 3.0005 2.9983 2.4975 2.5000 2.5005 3.0000 2.9978 2.4970 2.4995 2.5000 3.5005 3.5000 3.6255 3.4983 2.9975 3.0000 3.0005 3.6250 3.4978 2.9970 2.9995 3.0000 4.5005 3.7500 4.5000 3.7495 5.5005 4.5000 5.5000 4.4995 28.013 28.000 28.013 28.000 38.016 38.000 38.016 38.000 45.016 45.000 45.016 45.000 54.019 54.000 54.019 54.000 65.019 65.000 65.019 65.000 81.022 81.000 100.022 100.000 40.025 40.000 50.025 50.000 63.030 63.000 80.030 80.000 100.035 100.000 125.040 125.000 140.040 140.000 160.040 160.000 18.980 18.959 24.980 24.959 31.975 31.950 Straight Guide Pins NAAMS 32.025 32.000 40.025 40.000 50.025 50.000 63.030 63.000 80.030 80.000 100.035 100.000 115.035 115.000 125.040 125.000 Guide Pins with Shoulders NAAMS 32.060 32.050 40.060 40.050 50.060 50.050 63.070 63.060 80.072 80.062 100.083 100.073 115.035 115.000 125.040 125.000 18.980 18.959 24.980 24.959 31.975 31.950 end resulting in permanent distortion of the component. Tap Fit The component should be tapped using a soft hammer into the bored hole and secured with toe clamps. Wring Fit The component should be installed using a wringing (circular) motion with the heel of the hand. Wring fit components are to be held in place with toe clamps, retaining rings or plates.

Bearings Pressed Fit Chamfer Figure 8 Oil Groove Sharp Corner (Both Ends) For Machine Tools, Fixtures, etc. Straight Design, Wiper type Lamina-Bronze on steel provides longer wearing running fits No reaming or honing after press fitting bearing. HEAT TREATED L2 I.D. +.0005.0000 D2 O.D. +.0004.0000 D2 BEARINGS RUNNING FIT HARDENED RECOM- MENDED BORE SIZE +.0005.0000 L Bearings for Radial or Linear Applications I.D. +.0005.0000 D2 O.D. +.0004*.0000 RECOM- MENDED BORE SIZE +.0005.0000 L 625-x-75-RFB.75 175-x-175-RFB 1.75 625-x-100-RFB.6270 1.0014.9995 1.00 175-x-200-RFB 2.00 625-x-125-RFB 1.25 175-x-250-RFB 1.7530 2.2518 2.2495 2.50 750-x-75-RFB.75 175-x-300-RFB 3.00 750-x-100-RFB 1.00 175-x-350-RFB 3.50.7525 1.1264 1.1245 750-x-125-RFB 1.25 200-x-200-RFB 2.00 750-x-150-RFB 1.50 200-x-250-RFB 2.50 100-x-100-RFB 1.00 200-x-300-RFB 2.0035 2.5018 2.4995 3.00 100-x-125-RFB 1.25 200-x-350-RFB 3.50 100-x-150-RFB 1.0025 1.3764 1.3745 1.50 200-x-400-RFB 4.00 100-x-175-RFB 1.75 250-x-250-RFB 2.50 100-x-200-RFB 2.00 250-x-300-RFB 3.00 125-x-125-RFB 1.25 250-x-350-RFB 3.50 2.5035 3.2518 3.2490 125-x-150-RFB 1.50 250-x-400-RFB 4.00 125-x-175-RFB 1.2530 1.7516 1.7495 1.75 250-x-450-RFB 4.50 125-x-200-RFB 2.00 250-x-500-RFB 5.00 125-x-250-RFB 2.50 300-x-300-RFB 3.00 +.0005* 150-x-150-RFB 1.50 300-x-350-RFB.0000 3.50 150-x-175-RFB 1.75 300-x-400-RFB 4.00 3.0040 3.7520 3.7490 150-x-200-RFB 1.5030 2.0016 1.9995 2.00 300-x-450-RFB 4.50 150-x-250-RFB 2.50 300-x-500-RFB 5.00 150-x-300-RFB 3.00 300-x-600-RFB 6.00 *This diameter only. 19

Bearings Pressed Fit NON-HEAT TREATED Chamfer Figure 8 Oil Groove Sharp Corner (Both Ends) L2 For Machine Tools, Fixtures, etc. Straight Design, Wiper type Lamina-Bronze on steel provides longer wearing running fits Flash-plated O.D. prevents scoring when pressing bearing in and out I.D. +.0005.0000 D2 BEARINGS RUNNING FIT NON-HEAT-TREATED D2 O.D. +.0004.0000 RECOM- MENDED BORE SIZE +.0005.0000 L I.D. +.0005.0000 D2 O.D. +.0004.0000 RECOM- MENDED BORE SIZE +.0005.0000 *This diameter only. L SRFB-75-x-75.75 SRFB-175-x-200 2.00 SRFB-75-x-100 1.00 SRFB-175-x-225 2.25.7525 1.1265 1.1245 1.7530 2.1265 2.1245 SRFB-75-x-125 1.25 SRFB-175-x-250 2.50 SRFB-75-x-150 1.50 SRFB-175-x-300 3.00 SRFB-100-x-75.75 SRFB-200-x-100 1.00 SRFB-100-x-100 1.00 SRFB-200-x-125 1.25 SRFB-100-x-125 1.25 SRFB-200-x-150 1.50 1.0025 1.3765 1.3745 SRFB-100-x-150 1.50 SRFB-200-x-200 2.00 2.0035 2.3765 2.3745 SRFB-100-x-175 1.75 SRFB-200-x-250 2.50 SRFB-100-x-200 2.00 SRFB-200-x-300 3.00 SRFB-125-x-75.75 SRFB-200-x-350 3.50 SRFB-125-x-100 1.00 SRFB-200-x-400 4.00 SRFB-125-x-125 1.25 SRFB-250-x-125 1.25 SRFB-125-x-150 1.2530 1.6265 1.6245 1.50 SRFB-250-x-150 1.50 SRFB-125-x-175 1.75 SRFB-250-x-200 2.00 SRFB-125-x-200 2.00 SRFB-250-x-250 2.50 2.5035 2.8765 2.8745 SRFB-125-x-250 2.50 SRFB-250-x-300 3.00 SRFB-150-x-75.75 SRFB-250-x-350 3.50 SRFB-150-x-100 1.00 SRFB-250-x-400 4.00 SRFB-150-x-125 1.25 SRFB-250-x-500 5.00 SRFB-150-x-150 1.5030 1.8765 1.8745 1.50 SRFB-300-x-150 1.50 SRFB-150-x-175 1.75 SRFB-300-x-200 2.00 SRFB-150-x-200 2.00 SRFB-300-x-250 +.0005*.0000 2.50 SRFB-150-x-250 2.50 SRFB-300-x-300 3.00 3.0040 3.5020 3.4995 SRFB-175-x-100 1.00 SRFB-300-x-350 3.50 SRFB-175-x-125 1.25 SRFB-300-x-400 4.00 1.7530 2.1265 2.1245 SRFB-175-x-150 1.50 SRFB-300-x-500 5.00 SRFB-175-x-175 1.75 SRFB-300-x-600 6.00 20 Bearings for Radial or Linear Applications

Guide Bar Bushings Wring Fit Style D2 Used in Transfer Machinery Bronze Plated Steel for strength and lubricity Guide Bar Bushings are to be wring fit and held in place with toe clamps & screws. Please see clamping information on pages 16 & 17 and bore size information on page 18. Bearings Pressed Fit GUIDE BAR BUSHINGS D2 Wiper Head D2 D3 D4 L3 L4 L5 H Ground Unground Ground Unground.6254 GLMB-062 LMB-062.6252 1.0000 1.0160.930 1.125 1.210.750.460.370.188.7504 GLMB-075 LMB-075.7502 1.1250 1.1410 1.120 1.313 1.230.750.480.370.188 1.0004 GLMB-100 LMB-100 1.0002 1.3750 1.3910 1.560 1.750 1.550 1.000.550.490.188 1.2504 GLMB-125 LMB-125 1.2502 1.7500 1.7660 1.930 2.125 1.940 1.375.565.690.188 1.5004 GLMB-150 LMB-150 1.5002 2.0000 2.0160 2.180 2.375 2.060 1.500.560.750.188 1.7504 GLMB-175 LMB-175 1.7502 2.2500 2.2660 2.430 2.625 2.310 1.750.560.880.188 2.0004 GLMB-200 LMB-200 2.0002 2.5000 2.5160 2.750 2.938 2.570 2.000.570 1.000.250 2.5006 GLMB-250 LMB-250 2.5004 3.2500 3.2660 3.430 3.625 3.120 2.500.620 1.250.250 3.0008 GLMB-300 LMB-300 3.0006 3.7500 3.7660 3.930 4.125 3.620 3.000.620 1.500.250 3.7508 GLMB-375 LMB-375 3.7506 4.5000 4.5160 4.680 4.875 4.370 3.750.620 1.870.250 GLMB-450 LMB-450 NO CLAMPS & SCREWS 4.5008 4.5006 5.5000 5.5160 5.680 5.875 5.200 4.500.700 2.250.250 6 Bearings for Radial or Linear Applications STANDARD EXTRA-LONG 2 3 4 6 Recom-- mended Bore Size 1.0005 1.0000 1.1255 1.1250 1.3755 1.3750 1.7505 1.7500 2.0005 2.0000 2.2505 2.2500 2.5005 2.5000 3.2505 3.2500 3.7505 3.7500 4.5005 4.5000 5.5005 5.5000 PRECISION BEARINGS L3 B-6-175 3/4 B-7-175 7/8 B-8-175 1 B-10-200 1-1/4 B-12-200 1-1/2 B-7-300 7/8 B-8-300 1 B-10-300 1-1/4 B-12-300 1-1/2 B-14-300 1-3/4 B-16-300 2.187 B-20-300 2-1/2.250 Sharp Corner (Both Ends) NOM. PIN DIAMETER.7502.7500.8752.8750 1.0002 1.0000 1.2502 1.2500 1.5002 1.5000.8752.8750 1.0002 1.0000 1.2512 1.2500 1.5002 1.5000 1.7502 1.7500 2.0002 2.0000 2.5002 2.5000 H D3 D4 D-Clamps & Screws are included with wring fi t style bushings. D2 L 1.1272 1.1268 1.3772 1.3768 1.5022 1.5018 1.7522 1.7518 2.0022 2.0018 1.3772 1.3768 1.5022 1.5018 1.7522 1.7518 2.0022 2.0018 2.2522 2.2518 2.5022 2.5018 3.0022 3.0018 L5 L4 30.02 Flat 1-3/4 2 3 21

General Information Guide Pins Below are listed standard diameters and minimum/maximum lengths that we are able to machine to your specifi cations. We can also manufacture in-between diameters. We are able to make specials to meet your exact specifi catons. Please call, fax or e-mail for a quotation form. Every quote will be answered! Outside Diameter MINIMUM & MAXIMUM PIN S INCH Minimum Length Maximum Length Outside Diameter METRIC Minimum Length Maximum Length 0.625 1" 20" 0.750 1" 20" 18 & 19mm 25mm 500mm 0.875 1" 30" 1.000 1" 30" 24 & 25mm 25mm 760mm 1.125 2" 30" 1.250 2" 53" 30 & 32mm 50mm 1345mm 1.375 2" 53" 1.500 2" 53" 1.625 2" 53" 1.750 2" 53" 40 & 42mm 50mm 1345mm 1.875 2" 53" 2.000 3" 53" 50 & 52mm 75mm 1345mm 2.125 3" 53" 2.500 3" 53" 2.375 3" 53" 2.500 3" 53" 63mm 75mm 1345mm 2.625 3" 53" 2.750 3" 53" 3.000 4" 53" 3.125 4" 53" 3.250 4" 53" 80mm 100mm 1345mm 3.375 4" 53" 3.500 4" 53" 3.625 4" 53" 3.750 4" 53" 3.875 4" 53" 4.000 5" 53" 100mm 125mm 1345mm 4.125 5" 53" 4.250 5" 53" 4.375 5" 53" 4.500 5" 53" 115mm 125mm 1345mm 4.625 5" 53" 4.750 5" 53" 4.875 5" 53" 5.000 5" 53" 125mm 125mm 1345mm TN, ATN, TPB & TPC STRAIGHT PINS Lamina TPB & TPC Pins dimensions shown opposite for use in precision die sets. (Pins Available in Class 2) SHOULDER PINS For use with automotive, hardware, forming, or draw dies where stamping stock is thicker than 1/16, and clearances between punch and die sections will be more than.003 per side. (Pins available in Class 2) REMOVABLE PINS Designed specifi cally for all dies where it is desirable to remove pins for ease and simplicity of sharpening die. Lamina removable pins are generally used in carbide dies, progressive dies, lamination dies, and dies for very thin materials where clearances between punch and die sections will be no more than.0007 per side. Diameter TN Tolerance DIE PIN TOLERANCES Dimension ATN Tolerance HP Tolerance 0.7500 +.0000.0002 0.8750 1.0000.0002 +.0000 -.0003 -.0006 1.2500.0004 +.0000 -.0003 -.0007 1.5000 +.0000.0004 1.7500 2.0000 2.5000 3.0000 3.7500 4.5000 -.0003 -.0007 +.0000.0003 -.0004 -.0009 +.0000 -.0004.0003 -.0009 +.0000 -.0006.0003 -.0011 +.0000 -.0006.0003 -.0012 -.0008 -.0014 -.0008 -.0014 TPB & TPC Tolerance +.0000.0003 +.0000.0003 +.0000.0003 +.0000.0004 +.0000.0004 +.0000.0005 +.0000.0005 +.0000.0005 +.0000.0006 +.0000.0006 +.0000.0006 D2 Dimension TPC Press Tolerance +.0000.0006 +.0000.0006 +.0000.0006 +.0000.0008 +.0000.0008 +.0000.0008 +.0000.0008 +.0000.0008 +.0000.0008 +.0000.0010 +.0000.0010 Press Diameter 0.7520 0.8770 1.0020 1.2525 1.5025 1.7525 2.0025 2.5025 3.0025 3.7525 4.5025 22

Guide Pins Pressed Fit ATN-175-X-6 GUIDE PIN STRAIGHT GUIDE PIN STRAIGHT with Step Lead TN-750-X-4 4 TN-125-X-7 7 TN-750-X-4-1/2 4-1/2 TN-125-X-7-1/2 7-1/2 TN-750-X-5 5 TN-125-X-8 8 3/4" TN-750-X-6 6 TN-125-X-8-1/2 8-1/2 TN-750-X-7 7 TN-125-X-9 1-1/4" 9 TN-750-X-8 8 TN-125-X-9-1/2 9-1/2 TN-100-X-4 4 TN-125-X-10 10 TN-100-X-4-1/2 4-1/2 TN-125-X-11 11 TN-100-X-5 5 TN-125-X-12 12 TN-100-X-5-1/2 5-1/2 TN-150-X-5 5 TN-100-X-6 6 TN-150-X-5-1/2 5-1/2 TN-100-X-6-1/2 6-1/2 TN-150-X-6 6 1" TN-100-X-7 7 TN-150-X-6-1/2 6-1/2 TN-100-X-7-1/2 7-1/2 TN-150-X-7 7 TN-100-X-8 8 TN-150-X-7-1/2 7-1/2 TN-100-X-8-1/2 8-1/2 TN-150-X-8 1-1/2" 8 TN-100-X-9 9 TN-150-X-8-1/2 8-1/2 TN-100-x-10 10 TN-150-X-9 9 TN-125-X-4-1/2 4-1/2 TN-150-X-9-1/2 9-1/2 TN-125-X-5 5 TN-150-X-10 10 TN-125-X-5-1/2 1-1/4" 5-1/2 TN-150-X-11 11 TN-125-X-6 6 TN-150-X-12 12 TN-125-X-6-1/2 6-1/2 6 ATN-200-X-12 12 ATN-175-X-6-1/2 6-1/2 ATN-200-X-13 13 2" ATN-175-X-7 7 ATN-200-X-14 14 ATN-175-X-7-1/2 7-1/2 ATN-200-X-15 15 ATN-175-X-8 8 ATN-250-X-8 8 ATN-175-X-8-1/2 8-1/2 ATN-250-X-8-1/2 8-1/2 ATN-175-X-9 9 ATN-250-X-9 9 1-3/4" ATN-175-X-9-1/2 9-1/2 ATN-250-X-9-1/2 9-1/2 ATN-175-X-10 10 ATN-250-X-10 10 2-1/2" ATN-175-X-11 11 ATN-250-X-11 11 ATN-175-X-12 12 ATN-250-X-12 12 ATN-175-X-13 13 ATN-250-X-13 13 ATN-175-X-14 14 ATN-250-X-14 14 ATN-175-X-15 15 ATN-250-X-15 15 ATN-200-X-6 6 ATN-300-X-9 9 ATN-200-X-6-1/2 6-1/2 ATN-300-X-10 10 ATN-200-X-7 7 ATN-300-X-11 11 ATN-200-X-7-1/2 7-1/2 ATN-300-X-12 12 ATN-200-X-8 8 ATN-300-X-13 13 2" 3" ATN-200-X-8-1/2 8-1/2 ATN-300-X-14 14 ATN-200-X-9 9 ATN-300-X-15 15 ATN-200-X-10 10 ATN-300-X-17 17 ATN-200-X-10-1/2 10-1/2 ATN-300-X-19 19 ATN-200-X-11 11 ATN-300-X-21 21 TN and ATN pins are made of hardened steel with a precision-ground running diameter (), these guide pins are perfect mates for standard Lamina guide bushings. TN TN pins are centerless ground. ATN ATN pins are centerless ground. Please see bore size information on page 18. 23

GUIDE PIN STRAIGHT PRESS FIT END UNGROUND Guide Pins Pressed Fit L2 L2 TPB-750-X-4 4 TPB-175-X-6 6 TPB-750-X-4-1/2 4-1/2 TPB-175-X-6-1/2 6-1/2 TPB-750-X-5 5 TPB-175-X-7 7 TPB TPB-750-X-5-1/2 5-1/2 TPB-175-X-7-1/2 7-1/2 3/4" 1-3/8" TPB-750-X-6 6 TPB-175-X-8 8 TPB-750-X-7 7 TPB-175-X-8-1/2 8-1/2 TPB-750-X-7-1/2 7-1/2 TPB-175-X-9 9 TPB-750-X-8 8 TPB-175-X-9-1/2 1-3/4" 9-1/2 2-1/4" TPB-100-X-4 4 TPB-175-X-10 10 TPB-100-X-4-1/2 4-1/2 TPB-175-X-11 11 TPB-100-X-5 5 TPB-175-X-12 12 TPB-100-X-5-1/2 5-1/2 TPB-175-X-13 13 TPB-100-X-6 6 TPB-175-X-14 14 TPB-100-X-6-1/2 6-1/2 TPB-175-X-15 15 1" 1-1/2" TPB-100-X-7 7 TPB-175-X-17 17 TPB-100-X-7-1/2 7-1/2 TPB-200-X-6 6 TPB-100-X-8 8 TPB-200-X-6-1/2 6-1/2 TPB-100-X-8-1/2 8-1/2 TPB-200-X-7 7 TPB-100-X-9 9 TPB-200-X-7-1/2 7-1/2 TPB-100-X-10 10 TPB-200-X-8 8 L2 TPB-125-X-4 4 TPB-200-X-8-1/2 8-1/2 TPB-125-X-4-1/2 4-1/2 TPB-200-X-9 9 TPB-125-X-5 5 TPB-200-X-9-1/2 9-1/2 2" TPB-125-X-5-1/2 5-1/2 TPB-200-X-10 10 2-1/2" D2 TPB-125-X-6 6 TPB-200-X-11 11 TPB-125-X-6-1/2 6-1/2 TPB-200-X-12 12 TPB-125-X-7 7 TPB-200-X-13 13 TPB-125-X-7-1/2 1-1/4" 7-1/2 1-3/4" TPB-200-X-14 14 TPB-125-X-8 8 TPB-200-X-15 15 TPB-125-X-8-1/2 8-1/2 TPB-200-X-17 17 TPB-125-X-9 9 TPB-200-X-19 19 TPB-125-X-9-1/2 9-1/2 TPB-250-X-8 8 TPB-125-X-10 10 TPB-250-X-8-1/2 8-1/2 TPB-125-X-11 11 TPB-250-X-9 9 TPB-125-X-12 12 TPB-250-X-10 10 TPB-150-X-4-1/2 4-1/2 TPB-250-X-11 11 TPB-150-X-5 5 TPB-250-X-12 12 2-1/2" 3-1/2" TPB-150-X-5-1/2 5-1/2 TPB-250-X-13 13 TPB-375-X TPB-150-X-6 6 TPB-250-X-14 14 TPB-150-X-6-1/2 6-1/2 TPB-250-X-15 15 3-3/4" diameters TPB-150-X-7 7 TPB-250-X-17 17 TPB-150-X-7-1/2 7-1/2 TPB-250-X-19 19 & L2 lengths as specified TPB-150-X-8 8 TPB-250-X-21 21 TPB-150-X-8-1/2 8-1/2 TPB-300-X-9 9 1-1/2" 2" TPB-150-X-9 9 TPB-300-X-10 10 TPB-450-X TPB-150-X-9-1/2 9-1/2 TPB-300-X-11 11 TPB-150-X-10 10 TPB-300-X-12 12 4-1/2" diameters TPB-150-X-11 11 TPB-300-X-13 13 3" 4" TPB-150-X-12 12 TPB-300-X-14 14 & L2 lengths as specified TPB-150-X-13 13 TPB-300-X-15 15 TPB-150-X-14 14 TPB-300-X-17 17 TPB-150-X-15 15 TPB-300-X-19 19 Call for quotation on pins above. TPB-150-X-18 18 TPB-300-X-21 21 All TPB Guide Pins have centers &.015 stock left on the D2 diameter for grinding. See bore size information on page 18. 24

GUIDE PIN STRAIGHT PRESS FIT GROUND L2 L2 L2 TPC-750-X-4 4 TPC-150-X-8 8 TPC-300-X-9 9 TPC-750-X-4-1/2 4-1/2 TPC-150-X-8-1/2 8-1/2 TPC-300-X-10 10 TPC-750-X-5 5 TPC-150-X-9 9 TPC-300-X-11 11 TPC-750-X-5-1/2 5-1/2 TPC-150-X-9-1/2 1-1/2" 9-1/2 2" TPC-300-X-12 12 TPC-750-X-6 3/4" 6 1-3/8" TPC-150-X-10 10 TPC-300-X-13 13 3" TPC-750-X-6-1/2 6-1/2 TPC-150-X-11 11 TPC-300-X-14 14 TPC-750-X-7 7 TPC-150-X-12 12 TPC-300-X-15 15 TPC-750-X-7-1/2 7-1/2 TPC-175-X-6 6 TPC-300-X-17 17 TPC-750-X-8 8 TPC-175-X-6-1/2 6-1/2 TPC-300-X-19 19 TPC-875-X-4 4 TPC-875-X-4-1/2 4-1/2 TPC-175-X-7-1/2 7-1/2 TPC-875-X-5 5 TPC-175-X-8 8 TPC-875-X-5-1/2 5-1/2 TPC-175-X-8-1/2 8-1/2 TPC-875-X-6 7/8 6 1-1/2 TPC-175-X-9 9 TPC-875-X-6-1/2 6-1/2 TPC-175-X-9-1/2 1-3/4" 9-1/2 TPC-875-X-7 7 TPC-175-X-10 10 TPC-875-X-7-1/2 7-1/2 TPC-175-X-11 11 TPC-875-X-8 8 TPC-175-X-12 12 TPC-100-X-4 4 TPC-175-X-7 7 TPC-300-X-21 21 TPC-175-X-13 13 TPC-100-X-4-1/2 4-1/2 TPC-175-X-14 14 TPC-100-X-5 5 TPC-175-X-15 15 TPC-100-X-5-1/2 5-1/2 TPC-175-X-17 17 TPC-100-X-6 6 TPC-200-X-6 6 TPC-100-X-6-1/2 6-1/2 TPC-200-X-6-1/2 6-1/2 1" 1-1/2" TPC-100-X-7 7 TPC-200-X-7 7 TPC-100-X-7-1/2 7-1/2 TPC-200-X-7-1/2 7-1/2 TPC-100-X-8 8 TPC-200-X-8 8 TPC-100-X-8-1/2 8-1/2 TPC-200-X-8-1/2 8-1/2 TPC-100-X-9 9 TPC-200-X-9 9 TPC TPC-100-X-10 10 TPC-200-X-9-1/2 9-1/2 2" TPC-125-X-4 4 TPC-200-X-10 10 2-1/2" TPC-125-X-4-1/2 4-1/2 TPC-200-X-11 11 D2 TPC-125-X-5 5 TPC-200-X-12 12 D2 Specifi cations: TPC-125-X-5-1/2 5-1/2 TPC-200-X-13 13 +.0000 TPC-100 & smaller = nominal plus.0020.0006 TPC-125-X-6 6 TPC-200-X-14 14 TPC-125-300 = nominal plus.0025 +.0000.0008 TPC-125-X-6-1/2 6-1/2 TPC-200-X-15 15 +.0000 TPC-375 & 450 = nominal plus.0025.0010 TPC-125-X-7 7 TPC-200-X-17 17 TPC-125-X-7-1/2 1-1/4" 7-1/2 1-3/4" TPC-200-X-19 1519 TPC-125-X-8 8 TPC-250-X-8 8 TPC-375-X TPC-125-X-8-1/2 8-1/2 TPC-250-X-8-1/2 8-1/2 TPC-125-X-9 9 TPC-250-X-9 9 3-3/4" diameters TPC-125-X-9-1/2 9-1/2 TPC-250-X-10 10 TPC-125-X-10 10 TPC-250-X-11 11 & L2 lengths as specified TPC-125-X-11 11 TPC-250-X-12 12 2-1/2" 3-1/2" TPC-125-X-12 12 TPC-250-X-13 13 TPC-450-X TPC-150-X-4-1/2 4-1/2 TPC-250-X-14 14 TPC-150-X-5 5 TPC-250-X-15 15 TPC-150-X-5-1/2 5-1/2 TPC-250-X-17 17 4-1/2" diameters TPC-150-X-6 1-1/2" 6 2" TPC-250-X-19 19 TPC-150-X-6-1/2 6-1/2 TPC-250-X-21 21 TPC-150-X-7 7 TPC-150-X-7-1/2 7-1/2 Not all pins ground on centers. 2-1/4" L2 & L2 lengths as specified Call for quotation on pins above. 4" 25

Guide Pins Pressed Fit Metric Solid & Hollow These pins are made especially for automotive stamping companies. They conform to the standards agreed to by the North American Automotive Metric Standards group. AUTOMOTIVE METRIC NAAMS STANDARD 32, 40, 50 & 63 Dia. guide posts have M8 x 1.25-12 thread; 80, 100, 115 & 125 Dia. guide posts have M12 x 1.75-18 thread to facilitate handling from deep freeze. 26 SOLID Ground Unground G512512 G512514 G512516 G512518 G513214 G513216 G513218 G513220 G514014 G514016 G514018 G514020 G514022 G514025 G515016 G515018 G515020 G515022 G515025 G515028 G515031 G516318 G516320 G516322 G516325 G516328 G516331 G516335 G516340 G516350 G512512UG G512514UG G512516UG G512518UG G513214UG G513216UG G513218UG G513220UG G514014UG G514016UG G514018UG G514020UG G514022UG G514025UG G515016UG G515018UG G515020UG G515022UG G515025UG G515028UG G515031UG GUIDE PIN STRAIGHT NAAMS HOLLOW Ground 25 32 40 50 Tol g6 -.007 -.020 -.009 -.025 -.009 -.025 -.009 -.025 D2 25 32 40 50 D2 Tol r6 +.041 +.028 +.050 +.034 +.050 +.034 +.050 +.034 D4 Hollow Pins Only 125 140 160 180 140 160 180 200 140 160 180 200 225 250 160 180 200 225 250 280 315 180 200 225 250 280 315 355 400 500 G516318UG G516320UG G516322UG G416325UG -.010 +.060 G516328UG 63 63 -.029 +.041 G516331UG G516335UG G516340UG G516350UG G518022 G518022UG 225 G518025 G518028 G518031 G518035 G518040 G518045 G518050 G511031 G511035 G511040 G511045 G511050 G511055 G511060 G511065 G511140 G511150 G511235 G511240 G511245 G511250 G511255 G511260 G511265 G511270 G518025UG G518028UG G518031UG G518035UG G518040UG G518045UG G518050UG G511031UG G511035UG G511040UG G511045UG G511050UG G511055UG G511060UG G511065UG G511140UG G511150UG G511235UG G511240UG G511245UG G511250UG G511255UG G511260UG G511265UG G511270UG 80 GH511031 GH511035 GH511040 GH511045 GH511050 GH511055 GH511060 100 115 GH511235 GH511240 GH511245 GH511250 GH511255 GH511260 GH511265 125 -.010 -.029 -.012 -.034 -.012 -.034 -.014 -.039 80 100 115 125 +.062 +.043 +.073 +.051 +.076 +.054 +.088 +.063 50 65 250 280 315 355 400 450 500 315 355 400 450 500 550 600 650 400 500 355 400 450 500 550 600 650 700 L3 36 45 56 70 80 100 125 140 140 L3 D2 HOLLOW PIN D4 M12-1.75 x 30mm L3 Please see bore size information on page 18.

Guide Pins Pressed Fit Metric GUIDE PINS STRAIGHT METRIC Nom Pin Dia Nom Pin Dia TN-19MM-X-120 120 TN-25MM-X-220 220 TN-19MM-X-130 130 TN-25MM-X-240 240 25mm TN-19MM-X-140 140 TN-25MM-X-260 260 TN-19MM-X-150 150 TN-25MM-X-280 280 TN-19MM-X-160 19mm 160 TN-32MM-X-130 130 TN-19MM-X-170 170 TN-32MM-X-140 140 TN-19MM-X-180 180 TN-32MM-X-150 150 TN-19MM-X-190 190 TN-32MM-X-160 160 TN-19MM-X-200 200 TN-32MM-X-170 170 TN-25MM-X-120 120 TN-32MM-X-180 180 TN-25MM-X-130 130 TN-32MM-X-190 32mm 190 TN-25MM-X-140 140 TN-32MM-X-200 200 TN-25MM-X-150 150 TN-32MM-X-220 220 TN-25MM-X-160 25mm 160 TN-32MM-X-240 240 TN-25MM-X-170 170 TN-32MM-X-260 260 TN-25MM-X-180 180 TN-32MM-X-280 280 TN-25MM-X-190 190 TN-32MM-X-300 300 TN-25MM-X-200 200 TN -Metric TN pins are designed to be pressed into place. The ground bearing surface is equal top to bottom. TPB-40MM-X-130 STRAIGHT GUIDE PINS METRIC UNGROUND L2 TPB-50MM-X-260 L2 130 260 TPB-40MM-X-140 140 TPB-50MM-X-280 280 TPB-40MM-X-150 150 TPB-50MM-X-300 50mm 300 TPB-40MM-X-160 160 TPB-50MM-X-320 320 TPB-40MM-X-170 170 TPB-50MM-X-360 360 TPB-40MM-X-180 180 TPB-63MM-X-200 200 TPB-40MM-X-190 190 TPB-63MM-X-220 220 TPB-40MM-X-200 40mm 200 50mm TPB-63MM-X-240 240 TPB-40MM-X-220 220 TPB-63MM-X-260 260 TPB-40MM-X-240 240 TPB-63MM-X-280 280 63mm TPB-40MM-X-260 260 TPB-63MM-X-300 300 TPB-40MM-X-280 280 TPB-63MM-X-320 320 TPB-40MM-X-300 300 TPB-63MM-X-360 360 TPB-40MM-X-320 320 TPB-63MM-X-400 400 TPB-40MM-X-360 360 TPB-63MM-X-440 440 TPB-50MM-X-150 150 TPB-80MM-X-280 280 TPB-50MM-X-160 160 TPB-80MM-X-300 300 TPB-50MM-X-170 170 TPB-80MM-X-320 320 TPB-50MM-X-180 180 TPB-80MM-X-360 80mm 360 50mm 60mm TPB-50MM-X-190 190 TPB-80MM-X-400 400 TPB-50MM-X-200 200 TPB-80MM-X-440 440 TPB-50MM-X-220 220 TPB-80MM-X-500 500 TPB-50MM-X-240 240 60mm 80mm 100mm TPB - Metric L2 * *TPB pins have grind stock on the press fi t end. 27

Guide Pins Tap Fit +.0000.0002 Lamina demountable guide pins are tap fit and require toe clamps and screws to hold them in place. L5 The clamping flange is ground so that the flange fits squarely against the mounting surface. Please see pages 16 & 17 for toe clamp placement information and bore size information on page 18. D2 D3.187 L3 +.0000.0005 Heavy-duty X-40-Clamps are used to secure the pins to the die shoe. Clamps and screws are included. & D2 Nom Pin Dia D3 +.000.015 ±.010 L3 ±.010 GUIDE PINS DEMOUNTABLE L5 (Ref) NO. of CLAMPS & D2 Nom Pin Dia DGP0810 3.688 2.500 DGP1032 9.188 8.000 DGP0811 3.938 2.750 DGP1033 9.438 8.250 DGP0812 4.188 3.000 DGP1036 10.188 9.000 1-1/4 1.563 1.188 DGP0813 4.438 3.250 DGP1037 10.438 9.250 DGP0814 4.688 3.500 DGP1040 11.188 10.000 DGP0815 4.938 3.750 DGP1041 11.438 10.250 DGP0816 5.188 4.000 DGP1211 4.188 2.750 DGP0817 5.438 4.250 DGP1212 4.438 3.000 DGP0818 1 1.313 5.688 1.188 4.500 3 DGP1213 4.688 3.250 DGP0819 5.938 4.750 DGP1214 4.938 3.500 DGP0820 6.188 5.000 DGP1215 5.188 3.750 DGP0822 6.688 5.500 DGP1216 5.438 4.000 DGP0824 7.188 6.000 DGP1217 5.688 4.250 DGP0826 7.688 6.500 DGP1218 5.938 4.500 DGP0828 8.188 7.000 DGP1219 6.188 4.750 DGP0830 8.688 7.500 DGP1220 6.438 5.000 DGP0832 9.188 8.000 DGP1221 6.688 5.250 DGP1011 3.938 2.750 DGP1222 6.938 5.500 DGP1012 4.188 3.000 DGP1223 7.188 5.750 1-1/2 1.875 1.438 DGP1013 4.438 3.250 DGP1224 7.438 6.000 DGP1014 4.688 3.500 DGP1225 7.688 6.250 DGP1015 4.938 3.750 DGP1226 7.938 6.500 DGP1016 5.188 4.000 DGP1227 8.188 6.750 DGP1017 5.438 4.250 DGP1228 8.438 7.000 DGP1018 5.688 4.500 DGP1229 8.688 7.250 DGP1019 5.938 4.750 DGP1230 8.938 7.500 DGP1020 6.188 5.000 DGP1232 9.438 8.000 1-1/4 1.563 1.188 3 DGP1021 6.438 5.250 DGP1233 9.688 8.250 DGP1022 6.688 5.500 DGP1236 10.438 9.000 DGP1023 6.938 5.750 DGP1237 10.688 9.250 DGP1024 7.188 6.000 DGP1240 11.438 10.000 DGP1025 7.438 6.250 DGP1241 11.688 10.250 DGP1026 7.688 6.500 DGP1414 5.188 3.500 DGP1027 7.938 6.750 DGP1416 5.688 4.000 DGP1028 8.188 7.000 DGP1417 1-3/4 2.250 5.938 1.688 4.250 DGP1029 8.438 7.250 DGP1418 6.188 4.500 DGP1030 8.688 7.500 DGP1419 6.438 4.750 D3 +.000.015 ±.010 L3 ±.010 L5 (Ref) NO. of CLAMPS 3 3 4 28

Guide Pins Tap Fit +.0000.0002 Lamina demountable guide pins are tap fit and require toe clamps and screws to hold them in place. L5 The clamping flange is ground so that the flange fits squarely against the mounting surface. Please see pages 16 & 17 for toe clamp placement information and bore size information on page 18. D2 D3.187 L3 +.0000.0005 Heavy-duty X-40-Clamps are used to secure the pins to the die shoe. Clamps and screws are included. DGP1420 & D2 Nom Pin Dia D3 +.000.015 ±.010 6.688 L3 ±.010 GUIDEPINS DEMOUNTABLE L5 (Ref) 5.000 NO. of CLAMPS DGP2022 & D2 Nom Pin Dia DGP1422 7.188 5.500 DGP2024 7.938 6.000 DGP1424 7.688 6.000 DGP2026 8.438 6.500 DGP1426 8.188 6.500 DGP2028 8.938 7.000 DGP1428 8.688 7.000 DGP2030 9.438 7.500 DGP1430 9.188 7.500 DGP2032 9.938 8.000 DGP1432 1-3/4 2.250 9.688 1.688 8.000 4 DGP2034 10.438 8.500 DGP1434 10.188 8.500 DGP2036 10.938 9.000 2-1/2 3.031 1.938 DGP1436 10.688 9.000 DGP2038 11.438 9.500 DGP1438 11.188 9.500 DGP2040 11.938 10.000 DGP1440 11.688 10.000 DGP2042 12.438 10.500 DGP1446 13.188 11.500 DGP2048 13.938 12.000 DGP1448 13.688 12.000 DGP2054 15.438 13.500 DGP1614 5.438 3.500 DGP1630 9.438 7.500 DGP2432 10.438 8.000 2 2.500 1.938 4 DGP1632 9.938 8.000 DGP2434 10.938 8.500 3 3.500 2.438 DGP1634 10.438 8.500 DGP2436 11.438 9.000 D3 +.000.015 ±.010 7.438 L3 ±.010 L5 (Ref) 5.500 DGP2056 15.938 14.000 DGP1616 5.938 4.000 DGP2064 17.938 16.000 DGP1617 6.188 4.250 DGP2066 18.438 16.500 DGP1618 6.438 4.500 DGP2418 DGP1619 6.688 4.750 DGP2420 7.438 5.000 DGP1620 6.938 5.000 DGP2422 7.938 5.500 DGP1622 7.438 5.500 DGP2424 8.438 6.000 DGP1624 7.938 6.000 DGP2426 8.938 6.500 DGP1626 8.438 6.500 DGP2428 9.438 7.000 DGP1628 8.938 7.000 DGP2430 9.938 7.500 DGP1636 10.938 9.000 DGP2438 11.938 9.500 DGP1638 11.438 9.500 DGP2440 12.438 10.000 DGP1640 11.938 10.000 DGP2442 12.938 10.500 DGP1642 12.438 10.500 DGP2448 14.438 12.000 DGP1646 13.438 11.500 DGP2454 15.938 13.500 DGP1648 13.938 12.000 DGP2456 16.438 14.000 DGP1656 15.938 14.000 DGP2464 18.438 16.000 DGP1658 16.438 14.500 DGP2466 18.938 16.500 DGP1670 19.438 17.500 DGP2018 6.438 4.500 2-1/2 3.031 1.938 DGP2020 6.938 5.000 4 6.938 4.500 NO. of CLAMPS 4 4 29

Guide Pins Pressed Fit Shoulder type guide pins are for use with automotive, hardware, forming, or draw dies where stamping stock is thicker than 1/16, and clearances between punch and die sections will be more than.003 per side. Shoulder type guide pins are also valuable for repair of damaged dies where straight type pins no longer fit. Nom Pin Dia. GUIDE PINS WITH SHOULDERS D2 Press Dia. (Pins available in Class 2) L2 Nom Pin Dia. D2 Press Dia. HP-100-X-5-1/2 5-1/2 HP-200-X-8 8 HP-100-X-6 6 HP-200-X-8-1/2 8-1/2 HP-100-X-6-1/2 6-1/2 HP-200-X-9 9 1" 1-1/2" 1-1/2" HP-100-X-7 7 HP-200-X-10 10 HP-100-X-8 8 HP-200-X-11 11 2" 2-1/2" HP-100-X-9 9 HP-200-X-12 12 3-1/2" HP-125-X-6 6 HP-200-X-13 13 HP-125-X-7 7 HP-200-X-14 14 HP-125-X-7-1/2 1-1/4" 1-3/4" 7-1/2 2 HP-200-X-15 15 HP-125-X-8 8 HP-200-X-17 17 HP-125-X-9 9 HP-250-X-9 9 HP-150-X-6 6 HP-250-X-10 10 HP-150-X-6-1/2 6-1/2 HP-250-X-11 11 HP-150-X-7 7 HP-250-X-12 12 2-1/2" 3" HP-150-X-7-1/2 7-1/2 HP-250-X-13 13 4" HP-150-X-8 8 HP-250-X-14 14 HP-150-X-8-1/2 8-1/2 HP-250-X-15 15 1-1/2" 2" 2-1/2" HP-150-X-9 9 HP-250-X-17 17 HP-150-X-10 10 HP-300-X-11 11 HP-150-X-11 11 HP-300-X-12 12 HP-150-X-12 12 HP-300-X-14 3" 3-5/8" 14 5" HP-150-X-13 13 HP-300-X-15 15 HP-150-X-14 14 HP-300-X-17 17 HP-175-X-7-1/2 7-1/2 HP-300RA-X-11 11 HP-175-X-8 8 HP-300RA-X-12 12 HP-175-X-9 9 HP-300RA-X-13 13 3" 3-1/2" 5" HP-175-X-10 10 HP-300RA-X-14 14 1-3/4" 2-1/4" 3" HP-175-X-11 11 HP-300RA-X-15 15 HP-175-X-12 12 HP-300RA-X-17 17 HP-175-X-13 13 HP Pins can be manufactured in 3 3 /4 and 4 1 /2 HP-175-X-14 14 diameters in various lengths. See page 22. L2 L2 HP D2 D2 dimension is supplied with approximately.016 grindstock. HP Shoulder pins are meant to be press fit into place. 1/4 R 30

Guide Pins Tap Fit Metric Lamina has a wide variety of pins to meet most tool room requirements. Applications: Transfer Presses Repairs See page 17 for clamp placement instructions. GUIDE PINS WITH SHOULDERS METRIC Tol g6 D2 D2 Tol r6 D3 L3 L5 G503214 140 95 G503216 -.009 +.050 160 115 32 32 40 45 G503218 -.025 +.034 180 135 G503220 200 155 G504016 160 104 G504018 180 124 -.009 +.050 G504020 40 40 50 200 56 144 -.025 +.034 G504022 225 169 G504025 250 194 G505016 160 90 G505018 180 110 G505020 200 130 -.009 +.050 G505022 50 50 63 225 70 155 -.025 +.034 G505025 250 180 G505028 280 210 G505031 315 245 G506320 200 120 G506322 225 145 G506325 250 170 -.010 +.060 G506328 63 63 80 280 80 200 -.029 +.041 G506331 315 235 G506335 355 275 G506340 400 320 G508025 250 150 G508028 280 180 -.010 +.062 G508031 80 80 100 315 100 215 -.029 +.043 G508035 355 255 G508040 400 300 G501031 315 190 -.012 +.073 G501035 100 100 125 355 125 230 -.034 +.051 G501040 400 275 L5 L3 6 32, 40, 50 & 63 Dia. guide posts have M8 x 1.25-12 thread; 80, 100, 115 & 125 Dia. guide posts have M12 x 1.75-18 thread to facilitate handling from deep freeze. D2 D3 Must be held in place with toe clamps. G720000C toe clamps & screws are included. See pages 16 & 17 for clamping information; bore size information on page 18. 31

32 RP-100-X-5 GUIDE PIN REMOVABLE Nom. Pin Dia 5.000 L2 Tapped Hole RP-100-X-5-1/2 5.500 RP-100-X-6 6.000 Pin End RP-100-X-6-1/2 6.500 5/16-18x3/4 RP-100-X-7 1.0000" 7.000 1.500 RP-100-X-7-1/2 7.500 Install End +.0001 5/16-18 RP-100-X-8.0001 8.000 RP-100-X-8-1/2 8.500 RP-100-X-9 9.000 RP-125-X-5-1/2 5.500 RP-125-X-6 6.000 RP-125-X-6-1/2 6.500 RP-125-X-7 7.000 RP-125-X-7-1/2 7.500 Pin End RP-125-X-8 8.000 5/16-18x7/8 RP-125-X-8-1/2 1.2500" 8.500 1.750 RP-125-X-9 9.000 Install End +.0001 3/8-16 RP-125-X-10.0002 10.000 RP-125-X-11 11.000 RP-125-X-12 12.000 RP-125-X-13 13.000 RP-125-X-14 14.000 RP-150-X-5-1/2 5.500 RP-150-X-6 6.000 RP-150-X-6-1/2 6.500 Pin End RP-150-X-7 1.5000" 7.000 3/8-16x1 RP-150-X-7-1/2 7.500 2.000 +.0001 RP-150-X-8.0002 8.000 Install End 3/8-16 RP-150-X-8-1/2 8.500 RP-150-X-9 9.000 RP-150-X-10 10.000 RP-175-X-7 7.000 RP-175-X-7-1/2 7.500 Pin End RP-175-X-8 8.000 3/8-16x1 1.7500" 2.250 RP-175-X-8-1/2 8.500 Install End RP-175-X-9 +.0001 9.000 3/8-16.0002 RP-175-X-10 10.000 RP-200-X-6 6.000 RP-200-X-7 7.000 RP-200-X-7-1/2 7.500 RP-200-X-8 8.000 Pin End RP-200-X-8-1/2 8.500 3/8-16x7/8 RP-200-X-9 2.0000" 9.000 2.500 RP-200-X-10 10.000 Install End +.0001 3/8-16 RP-200-X-11.0003 11.000 RP-200-X-12 12.000 RP-200-X-13 13.000 RP-200-X-14 14.000 RP-250-X-9 9.000 RP-250-X-10 10.000 Pin End RP-250-X-11 11.000 1/2-13x1 2.5000" 3.500 RP-250-X-12 12.000 Pin End RP-250-X-13 +.0001 13.000 1/2-13.0003 RP-250-X-14 14.000 RP-300-x- 3.0000" Non-Stock; call for quotation Guide Pins Removable Pressed Fit Bushing Liner Designed specifically for all dies where it is desirable to remove pins for ease and simplicity of sharpening die. Lamina removable pins are generally used with carbide dies, progressive dies, lamination dies, and dies for very thin materials where clearances between punch and die sections will be no more than.0007 per side. Can be used with Plain Bearing & Keyless Ball-Bearing Bushing and Retainers. ASSEMBLIES 3/8 L2 2 2 REMOVABLE PIN D2* BUSHING LINER END CAP SOCKET HEAD CAP Tapped Hole Pin End Tapped Hole Install End Ground for REMOVABLE PIN Unground Nom. Pin Dia. GRP-100-ASSY RP-100-ASSY 1.000 GRP-125-ASSY RP-125-ASSY 1.250 GRP-150-ASSY RP-150-ASSY 1.500 GRP-175-ASSY RP-175-ASSY 1.750 GRP-200-ASSY RP-200-ASSY 2.000 GRP-250-ASSY RP-250-ASSY 2.500 GRP-300-ASSY RP-300-ASSY 3.000 Assembly includes 1 bushing liner, 1 End Cap & 1 Socket Head Cap Screw Ground BUSHING LINER for REMOVABLE PIN Unground Nom. Pin Dia. D2* O.D. Length GNRB-100 NRB-100 1.000 1.5008 1.5006 1.625 GNRB-125 NRB-125 1.250 1.7508 1.7506 1.875 GNRB-150 NRB-150 1.500 2.0008 2.0006 2.125 GNRB-175 NRB-175 1.750 2.2508 2.2506 2.375 GNRB-200 NRB-200 2.000 2.5008 2.5006 2.625 GNRB-250 NRB-250 2.500 3.0008 3.0006 3.625 GNRB-300 NRB-300 3.000 3.5008 3.5006 4.125 *.016 stock left on this diameter on unground liner forgrindingtofitboredholeindieshoe END CAP for REMOVABLE PIN Nom. Pin Dia O.D. Soc Hd Screw RC-100- END-CAP 1.000 1.250 5/16-18x1 RC-125-END-CAP 1.250 1.500 3/8-16x1 RC-150-END-CAP 1.500 1.750 3/8-16x1 RC-175-END-CAP 1.750 2.000 3/8-16x1 RC-200-END-CAP 2.000 2.250 3/8-16x1 RC-250-END-CAP 2.500 2.750 1/2-13x1.5 RC-300-END-CAP 3.000 3.250 1/2-13x1.5 Removable pins, assemblies and screws are sold separately.

Stripper Bushings Clamp & Pressed Fit Types Lamina manufactures components specifi cally for use in dies where stripping operations take place such as in lamination dies. These components are made to close tolerances. Ground STRIPPER GUIDE PIN BUSHINGS BRONZE PLATED Assembly includes bushing, clamps and screws Nom. Bolt Pin D2 D3 D4 L2 Circle *Unground Dia. Dia. GCG-75 CG-75 3/4 GCG-100 CG-100 1 *.016 grind stock on these diameters. No. "D" Clamps.7503 1.1254.7502 1.1252 1.125 1.313 1.625 1.000 1.719 2 1.0003 1.3754 1.375 1.0002 1.3752 1.563 1.625 1.000 1.969 3 L2 D2* D3 +.005.000.187 D4 Ground STRIPPER BUSHINGS BRONZE PLATED PRESS FIT TYPE *Unground Nom. Pin Dia. GHG-62 HG-62 5/8 GHG-75 HG-75 3/4 GHG-100 HG-100 1 D2 D4 +.000.015.6253 1.0004.6252 1.0002.7503 1.1254.7502 1.1252 1.0003 1.0002 1.3754 1.3752 +000.031 1.125 1 1.250 1 1.500 1 D4 D2* +.000.005.125 *.016 grind stock on these diameters. Ground STRIPPER BUSHING STRAIGHT TYPE *Unground Nom. Pin Dia. GSG-100-L SG-100-L 1 *.020 grind stock on this diameter. D2 L 1.0002 1.0004 1.3754 1.3752 2.375.188.875 D2* 34

Stripper Pins Pressed Fit & Flange Types STRIPPER PINS PRESS FIT TYPE Nom. Pin Dia. D2* L2 L3.6250 SGP-62-X-4 5/8.6248.640 4.00 2.25.750.6250 SGP-62-X-5 5/8.6248.640 5.00 2.25.750 SGP-75-X-5 3/4.7500.7498.765 5.00 2.25.875.7500 SGP-75-X-6-1/2 3/4.7498.765 6.50 2.75.875 1.0000 SGP-100-X-6-1/2 1 0.9998 1.015 6.50 2.75 1.000 SGP-100-X-7-1/2 1 1.0000 0.9998 1.015 7.50 2.75 1.000 *The D2 diameter is unground. Suggested finish grind size for D2 dimension to be.001 over nominal pin diameter. L2 L3.406 D2* 3/4 CG Type 1/4 G Screw DIE SHOE D3 STRIPPER PLATE DIE RETAINER DIE SHOE HG Type R1 L2 STRIPPER PIN & BUSHING APPLICATION Nom. Pin Dia. STRIPPER PIN FLANGE STYLE D2* ±.003 D3 L2 L3 R1 "G" Screws F-8890 7/8.8750.8748.900 2.00 9.00 3.750 3.00.719 Flat Head F-1080 1 1.0000 0.9998 1.025 2.00 8.00 3.500 1.50.750 Soc. Head F-1085 1 1.0000 0.9998 1.025 2.00 8.50 3.500 1.50.750 Soc. Head F-1090 1 1.0000 0.9998 1.025 2.00 9.00 3.500 1.50.750 Soc. Head F-1290 1-1/4 1.2500 1.2498 1.275 2.25 9.00 3.500 1.50.875 Soc. Head *The D2 diameter is unground. Suggested finsh bore size to be.005 over nominal pin diameter. 1 L3 D2.250 35

HEAVY DUTY STOCK LIFTERS MODEL 75 HARDENED, GROUND AND VENTED Rockwell: RC 52-56 Case Hardened.015.030 Deep Packaged complete with spring, screw and retaining washer When ordering please specify: 1. Quantity 2. Catalog Number Lifters with travel greater than 1.75 are available. Priced on application. (Furnished without spring.) W Dia. R Dia. U T S V Radius PURPOSE Available as Replacement Part No. DL75 Die Life Retaining Washer. 6 per package. Includes fl at head socket screw 5/16-18x1. Note: In blanking die sections order optional Die Life DL Retaining Washers: Counterbore hole must be deeper. DIE LIFE REPLACEMENT RETAINING WASHER & SCREW KIT R S T U V W DL75.656.490.280.585.390.330 LIFTER SPECIFICATIONS A Operating Travel D Pocket Depth for Spring B Lifter Body Length E Spring Free Length C Pocket Depth for Lifter Body F Slot Length MODEL 75 Stock Lifter O.D..7495 (For Stock up to.094 thick) A TRAVEL B LIFTER C LIFTER POCKET D SPRING POCKET Replacement Washer #75WASHER Replacement Screw #75SCREW Die Life Package #DL75 (6 per package) E F SPRING FREE SLOT REPLACE- MENT DIE SPRING Lbs @1/10" SPRING DEFLECT- ION 75-50 0.50 2.312 2.50 2.938 2.50 1.000 M113L 4.5 75-75 0.75 2.562 2.75 3.938 3.50 1.250 M115L 3.0 75-1-0 1.00 2.812 3.00 4.938 4.50 1.500 M115AL 2.5 75-1-25 1.25 3.062 3.25 5.938 5.50 1.750 M115BL 2.1 75-1-50 1.50 3.312 3.50 6.938 6.50 2.000 M115CL 1.4 75-1-75 1.75 3.562 3.75 7.938 7.50 2.250 M115DL 1.2 VALUES CONSTANT FOR ALL 75 LIFTERS a.578 Dimension between CL of Lifter Pocket to CL of Socket Screw b.203 Slot Depth ±.005 c.750 Pocket Diameter for Lifter Body +.001.000 d.688 Counter Bore Diameter for Lifter Washer f.25 Counter Bore Depth in Stripper Plate, minus half of stock thickness g.781 Counter Bore Diameter in Stripper Plate h.7495 Lifter Body Diameter +.0000.0015 i.125 Slot Height (for Stock) ±.005 j.187 Dimension from Top of Slot to Top of Body ±.005 k 1.000 ˆLength of Spring Pocket in Lifter Body m.50 Spring Pocket Diameter n 1.125 Dimension from Bottom of Washer (Slot) to Bottom of Body p.375 Counter Bore Depth for Washer & Socket Screw d Counterbore F n p.156 5/16-18 x 5/8 Socket Button Head Screw a.187 h g b c REAM i f j A Travel k E Counterbore in stripping plate B C D m 36

HEAVY DUTY STOCK LIFTERS MODEL 112 HARDENED, GROUND AND VENTED Rockwell: RC 52-56 Case Hardened.015.030 Deep Packaged complete with spring, screw and retaining washer When ordering please specify: 1. Quantity 2. Catalog Number Lifters with travel greater than 1.75 are available. Priced on application. (Furnished without spring.) W Dia. R Dia. U T S V PURPOSE Available as Replacement Part No. D12 Die Life Retaining Washer. 6 per package. Includes fl at head socket screw 3/8-16x1-1/4. Note: In blanking die sections order optional Die Life DL Retaining Washers: Counterbore hole must be deeper. DIE LIFE REPLACEMENT RETAINING WASHER & SCREW KIT R S T U V W D12.840.550.300.830.580.406 LIFTER SPECIFICATIONS A Operating Travel D Pocket Depth for Spring B Lifter Body Length E Spring Free Length C Pocket Depth for Lifter Body F Slot Length MODEL 112 Stock Lifter O.D. 1.1245 (For Stock up to.156 thick) d Counterbore b c REAM A TRAVEL B LIFTER C LIFTER POCKET D SPRING POCKET E F SPRING FREE SLOT REPLACE- MENT DIE SPRING Lbs @1/10" SPRING DEFLECT- ION 112-50 0.50 2.812 2.625 3.063 2.50 1.250 M4L 12.0 112-75 0.75 3.062 2.875 4.063 3.50 1.500 M6L 8.0 112-1-0 1.00 3.312 3.125 5.063 4.50 1.750 M8L 6.4 112-1-25 1.25 3.562 3.375 6.063 5.50 2.000 M10L 5.5 112-1-50 1.50 3.812 3.625 7.063 6.50 2.250 M11BL 4.5 112-1-75 1.75 4.062 3.875 8.063 7.50 2.500 M11CL 3.8.250 a h g i f j Counterbore in stripping plate Replacement Washer #112 WASHER Replacement Screw #112 SCREW Die Life Package #D12 (6 per package) VALUES CONSTANT FOR ALL 112 LIFTERS a.828 Dimension between CL of Lifter Pocket to CL of Socket Screw b.329 Slot Depth ±.005 c 1.125 Pocket Diameter for Lifter Body +.001.000 d.875 Counter Bore Diameter for Lifter Washer f.50 Counter Bore Depth in Stripper Plate, minus half of stock thickness g 1.156 Counter Bore Diameter in Stripper Plate h 1.1245 Lifter Body Diameter +.0000.0015 i.188 Slot Height (for Stock) ±.005 j.406 Dimension from Top of Slot to Top of Body ±.005 k 1.125 Length of Spring Pocket in Lifter Body m.75 Spring Pocket Diameter n 1.312 Dimension from Bottom of Washer (Slot) to Bottom of Body p.394 Counter Bore Depth for Washer & Socket Screw F p n.156 3/8-16 x 1.00 Socket Button Head Screw A Travel k E B C D m 37

HEAVY DUTY RAIL STOCK LIFTER PINS MODEL T-750 HARDENED, GROUND AND VENTED Rockwell: RC 52-56 Case Hardened.015.030 Deep Package complete with spring, screw and retaining washer. When ordering please specify: 1. Quantity 2. Catalog Number 5/16-18 x.625 tap LIFTER SPECIFICATIONS A Operating Travel D Pocket Depth for Spring B Lifter Body Length E Spring Free Length C Pocket Depth for F Slot length Lifter Body G Top of Die to Top of Lifter Body d Counter bore c REAM Rail Stock Lifter O.D..7495 +.0000.0015 A TRAVEL B LIFTER C&D LIFTER POCKET G E SPRING FREE F SLOT Optional: Tack Weld at As- REPLACE- MENT DIE SPRING Lbs @1/10" SPRING DEFLECTION T-750-50 0.50 2.312 2.500 1.187 2.50 1.000 M113L 4.5 T-750-75 0.75 2.562 3.500 1.437 3.50 1.250 M115L 3.0 T-750-1-0 1.00 2.812 4.500 1.687 4.50 1.500 M115AL 2.5 T-750-1-25 1.25 3.062 5.500 1.937 5.50 1.750 M115BL 2.1 T-750-1-50 1.50 3.312 6.500 2.187 6.50 2.000 M115CL 1.4 T-750-1-75 1.75 3.562 7.500 2.437 7.50 2.250 M115DL 1.2 Replacement Washer Part Number 75WASHER Replacement Screw Part Number 75SCREW G F p.187.156 h a A Travel Rail & Screw Not Furnished B n k VALUES CONSTANT FOR ALL 75 -T LIFTERS a.578 Dimension between CL of Lifter Pocket to CL of Socket Screw c.750 Pocket Diameter for Lifter Body +.001.000 d.688 Counter Bore Diameter for Lifter Washer h.7495 Lifter Body Diameter +.0000.0015 C & D 5/16-18 x 5/8 Socket Button Head Screw E i.125 Slot Height (for Stock) ±.005 j.187 Dimension from Top of Slot to Top of Body ±.005 k n p 1.000 ˆLength of Spring Pocket in Lifter Body 1.125 Dimension from Bottom of Washer (Slot) to Bottom of Body.375 Counter Bore Depth for Washer & Socket Screw 38

HEAVY DUTY RAIL STOCK LIFTER PINS MODEL 112T HARDENED, GROUND AND VENTED Rockwell: RC 52-56 Case Hardened.015.030 Deep Package complete with spring, screw and retaining washer. When ordering please specify: 1. Quantity 2. Catalog Number 3/8-16 x 1 tap LIFTER SPECIFICATIONS A Operating Travel D Pocket Depth for Spring B Lifter Body Length E Spring Free Length C Pocket Depth for F Slot length Lifter Body G Top of Die to Top of Lifter Body d Counter bore c Ream Rail Stock Lifter O.D. 1.1245 +.0000.0015 A TRAVEL B LIFTER C&D LIFTER POCKET G E F SPRING SLOT F.L. REPLACE- MENT DIE SPRING Lbs @1/10" SPRING DEFLECTION 112T-50 0.50 2.812 2.562 1.500 2.50 1.250 M4L 12.0 112T-75 0.75 3.062 3.562 1.750 3.50 1.500 M6L 8.0 112T-1-00 1.00 3.312 4.562 2.000 4.50 1.750 M8L 6.4 112T-1-25 1.25 3.562 5.562 2.250 5.50 2.000 M10L 5.5 112T-1-50 1.50 3.812 6.562 2.500 6.50 2.250 M11BL 4.5 112T-1-75 1.75 4.062 7.562 2.750 7.50 2.500 M11CL 3.8 Replacement Washer Part Number 112WASHER Replacement Screw Part Number 112SCREW G F p.250 h a Optional Tack Weld at Assembly A Travel Rail & Screw Not Furnished.156 B n k VALUES CONSTANT FOR ALL 112-T LIFTERS a.828 Dimension between CL of Lifter Pocket to CL of Socket Screw c 1.125 Pocket Diameter for Lifter Body +.001.000 d.875 Counter Bore Diameter for Lifter Washer h 1.1245 Lifter Body Diameter +.0000.0015 C & D 3/8-16 x 1.00 Socket Button Head Screw E i.188 Slot Height (for Stock) ±.005 j.406 Dimension from Top of Slot to Top of Body ±.005 k n p 1.125 Length of Spring Pocket in Lifter Body 1.312 Dimension from Bottom of Washer (Slot) to Bottom of Body.394 Counter Bore Depth for Washer & Socket Screw 39

Mini-Lifters Top or Side Mounted 3/8 and 1/2 diameters each to 3 different lengths. Hardened, ground and vented. Accurately machined from solid bar steel and packaged complete with spring, socket head cap screw, dog point screw and retaining washer. Immediately available from Inventory. ML-50-63 ML-50-44 ML-50-25 OPTIONAL DIE LEVEL FULL SCALE TEMPLATE ML-38-25 ML-38-44 ML-38-63.5R.130 ±.010.000 Air Relief.160 Width of slot 1 /4-20 Dog Pt. Screw & Lock Nut.475.500 Ream.500 Dia. Dog Point Washer Note: Can be guided by dog point washer or dog point screw 10-24 Dog Pt. Screw & Lock Nut.130 Width of Slot.38R.130 ±.010.000.375 Ream.375 Dia. Air Relief.355 A TRAVEL B C BORE D MIN E F SPRING SLOT FREE REPLACE- MENT DIE SPRING Lbs @ 1/10" SPRING DEFLEC- TION ML-50-25.25 1.28 2.13 2.30 5.50.990 M111L 6.8 ML-50-44.44 1.47 2.63 2.80 6.50 1.180 M112L 5.5 ML-50-63.63 1.66 3.13 3.30 7.50 1.370 M113L 4.5 A TRAVEL B C BORE D MIN E F SPRING SLOT FREE REPLACE- MENT DIE SPRING Lbs @ 1/10" SPRING DEFLEC- TION ML-38-25.25 1.25 2.13 2.30 2.50.970 M101L 4.0 ML-38-44.44 1.44 2.63 2.80 3.00 1.160 M102L 2.8 ML-38-63.63 1.63 3.13 3.30 3.50 1.350 M103L 2.4.17.56 Dia..12 ML-50 +.0000.0005.4990 Dia..16.16.17.44 Dia..09 ML-38 +.0000.0005.3740 Dia..16.155 B.54 Opt..10 A Travel.16 1 /4-20x.5 Screw.62 F B.07.56 Opt. A Travel.13 10-24x.38 Screw.62 F.21.13.125 C E D Min. 1 /8 Initial Spring Comp. 4 to 1 Ratio C E D Min. 40

Design in (and build in) stock lifters just as easily as you do die springs and pins. Standard notched lifters are made in two sizes to handle stock up to.156 thick. Side center-rail lifters that easily accept your special rails are also offered. These lifters all install from the top only. Easier to do and they can be replaced without taking the die from the press. All they need are two drilled holes, one tapped. Drop the spring and lifter in the larger one and secure them with the retaining screw in the tapped hole. Go to standard lifters for consistent quality they re all solid bar steel, hardened, ground and vented. You can t build them yourself for less. 75-50 T-750-50 75-75 T-750-75 75-1-0 T-750-1-0 75-1-25 T-750-1-25 75-1-50 T-750-1-50 75-1-75 T-750-1-75 112-50 112T-50 112-75 112T-75 112-1-0 112T-1-00 112-1-25 112T-1-25 112-1-50 112T-1-50 112-1-75 112T-1-75 ML-38-25 ML-38-44 ML-38-63 ML-50-25 ML-50-44 ML-50-63 STOCKLIFTER REPLACEMENT S REPLACEMENT SPRING M113L M115L M115AL M115BL M115CL M115DL M4L M6L M8L M10L M11BL M11CL M101L M102L M103L M111L M112L M113L REPLACEMENT WASHERS REPLACEMENT SCREW DIELIFEKIT 6SETS 75WASHER 75SCREW DL75 75WASHER 75SCREW DL75 75WASHER 75SCREW DL75 75WASHER 75SCREW DL75 75WASHER 75SCREW DL75 75WASHER 75SCREW DL75 112WASHER 112SCREW D12 112WASHER 112SCREW D12 112WASHER 112SCREW D12 112WASHER 112SCREW D12 112WASHER 112SCREW D12 112WASHER 112SCREW D12 38WASHER 50WASHER 41

LIFTER PINS METRIC Lifter pins are manufactured from 1144 steel and are commonly used to handle large die sets. They conform to NAAMS standards. The internal spring provides added assurance that the fall ring will function properly during the course of the pin s use. NAAMS A B C D E F Total Die Wt. in Code (mm) (mm) (mm) (mm) (mm) (mm) Metric Tons (t) LP35-125 L013512 35 125 165 45 10 21.5 0 2.72 LP50-190 L015019 50 190 230 63 10 31 2.72 9.07 LP63-280 L016328 63 280 320 76 10 37.5 9.07 36.28 LP80-320 L018032 80 320 370 89 15 46 36.28 72.57 42

STOP BLOCKS These stop blocks are precision machined from 1018 material. Additionally, the blocks are inspected to provide uniform quality and dimensions. The length dimension is.060 oversize. NO. Diameter Length (in) D (in) A (in) 20-150CSB 2.00 1.50 20-200CSB 2.00 2.00 2.00 20-250CSB 2.00 2.50 20-300CSB 2.00 2.00 3.00 20-350CSB 2.00 3.50 20-400CSB 2.00 4.00 20-425CSB 2.00 4.25 20-475CSB 2.00 4.75 20-525CSB 2.00 5.25 2.00 20-550CSB 2.00 5.50 20-600CSB 2.00 6.00 2.00 20-650CSB 2.00 6.50 25-150CSB 2.50 1.50 25-200CSB 2.50 2.00 2.50 25-250CSB 2.50 2.50 25-300CSB 2.50 3.00 2.50 25-350CSB 2.50 3.50 25-400CSB 2.50 4.00 25-425CSB 2.50 4.25 25-475CSB 2.50 4.75 25-525CSB 2.50 5.25 25-550CSB 2.50 2.50 5.50 25-600CSB 2.50 6.00 25-650CSB 2.50 2.50 6.50 43

PAD RETAINERS LOCKING INCH, STANDARD MOUNT Pad retainers are manufactured from 1144 steel and hardened to 28-34 Rockwell C-scale. They are machined to precise tolerances in order to retain the pad and assure parallelism during use. The NP Series is also available, by special order, that offers three prongs as opposed to knurl. S1 Socket Set Screw S2 Socket Head Cap Screw Diam. Diam. Length ±.005 NO. (in) D2 (in) (in) L2 (in) L3 (in) L4 (in) S1 (in) S2 (in) 100-100 1.00 1.00 100-125 1.25 1.25 100-150 1.50 1.50 100-175 1.75 1.75 100-200 2.00 2.00 100-225 1.00.75 2.25 1.00.38 2.25 5/8 18 5/16 18 100-250 2.50 2.50 100-275 2.75 2.75 100-300 3.00 3.00 100-325 3.25 3.25 100-350 3.50 3.50 106-100 1.00 1.00 106-125.81 1.25 1.06 1.25 106-150.81 1.50 1.06 1.50 106-175.81 1.75 1.06 1.75 106-200.81 2.00 1.06 2.00 106-225 1.06.81.81 2.25 1.06 1.00.375 2.25 5/8 18 5/16 18 106-250.81 2.50 1.06 2.50 106-275.81 2.75 1.06 2.75 106-300.81 3.00 1.06 3.00 106-325.81 3.25 1.06 3.25 106-350.81 3.50 1.06 3.50 125-100 1.00 1.00 125-125 1.00 1.25 1.25 1.25 125-150 1.00 1.50 1.25 1.50 125-175 1.00 1.75 1.25 1.75 125-200 1.00 2.00 1.25 2.00 125-225 1.00 2.25 1.25 2.25 125-250 1.00 2.50 1.25 2.50 125-275 1.00 2.75 1.25 2.75 125-300 1.00 1.25 1.00 3.00 1.25 1.12.50 3.00 3/4 16 3/8 16 125-325 1.00 3.25 1.25 3.25 125-350 1.00 3.50 1.25 3.50 125-375 1.00 3.75 1.25 3.75 125-400 1.00 4.00 1.25 4.00 125-450 1.00 4.50 1.25 4.50 125-500 1.00 5.00 1.25 5.00 125-550 1.00 5.50 1.25 5.50 125-600 1.00 6.00 1.25 6.00 162-100 1.00 1.25 162-125 1.25 1.50 162-150 1.25 1.50 1.62 1.75 162-175 1.25 1.75 1.62 2.00 162-200 1.25 2.00 1.62 2.25 162-225 1.25 2.25 1.62 2.50 1.62 1.25 1.12.50 7/8 14 1/2 13 162-250 1.25 2.50 1.62 2.75 162-275 1.25 2.75 1.62 3.00 162-300 1.25 3.00 1.62 3.25 162-325 1.25 3.25 1.62 3.50 162-350 1.25 3.50 1.62 3.75 162-375 1.25 3.75 1.62 4.00 ASSEMBLY INCLUDES: Retainer Body Socket Head Cap Screws Socket Set Screw LOAD RADIUS RATING NO. (in) lbs. 100-XXX.03 1,500 106-XXX.03 1,500 125-XXX.03 3,000 162-XXX.06 5,000 187-XXX.06 7,500 200-XXX.06 10,000 Diam. Diam. Length ±.005 NO. (in) D2 (in) (in) L2 (in) L3 (in) L4 (in) S1 (in) S2 (in) 162-400 4.00 4.25 162-450 4.50 4.75 162-500 1.62 1.25 5.00 1.12.50 5.25 7/8 14 1/2 13 162-550 5.50 6.00 162-600 6.00 6.50 187-125 1.25 1.50 187-150 1.50 1.75 187-175 1.75 1.87 2.00 187-200 2.00 1.87 2.25 187-225 2.25 1.87 2.50 187-250 2.50 1.87 2.75 187-275 2.75 1.87 3.00 187-300 1.87 1.50 3.00 1.87 1.25.50 3.25 187-325 3.25 1.87 3.50 1-1/8 12 5/8 11 187-350 3.50 1.87 3.75 187-375 3.75 1.87 4.00 187-400 4.00 1.87 4.25 187-450 4.50 1.87 5.00 187-500 5.00 1.87 5.50 187-550 5.50 1.87 6.00 187-600 6.00 1.87 6.50 200-150 1.50 2.00 200-175 1.75 2.00 2.25 200-200 2.00 2.00 2.50 200-225 2.25 2.00 2.75 200-250 2.50 2.00 3.00 200-275 2.75 2.00 3.25 200-300 3.00 2.00 3.50 200-325 2.00 1.62 3.25 2.00 1.38.50 3.75 1-1/4 12 3/4 10 200-350 3.50 2.00 4.00 200-375 3.75 2.00 4.25 200-400 4.00 2.00 4.50 200-450 4.50 2.00 5.00 200-500 5.00 2.00 5.50 200-550 5.50 2.00 6.00 200-600 6.00 2.00 6.50 44

PAD RETAINERS LOCKING INCH, STANDARD MOUNT, WITH FLATS S1 Socket Set Screw S2 Socket Head Cap Screw Diam. Diam. Length ±.005 NO. (in) D2 (in) (in) L2 (in) L3 (in) L4 (in) S1 (in) S2 (in) 100-100F 1.00 1.00 100-125F 1.25 1.25 100-150F 1.50 1.50 100-175F 1.75 1.75 100-200F 2.00 2.00 100-225F 1.00.75 2.25 1.00.38 2.25 5/8 18 5/16 18 100-250F 2.50 2.50 100-275F 2.75 2.75 100-300F 3.00 3.00 100-325F 3.25 3.25 100-350F 3.50 3.50 106-100F.8 1.00 1.06 1.00 106-125F.81 1.25 1.06 1.25 106-150F.81 1.50 1.06 1.50 106-175F.81 1.75 1.06 1.75 106-200F.81 2.00 1.06 2.00 106-225F 1.06.81.81 2.25 1.00.375 2.25 5/8 18 5/16 18 106-250F.81 2.50 1.06 2.50 106-275F.81 2.75 1.06 2.75 106-300F.81 3.00 1.06 3.00 106-325F.81 3.25 1.06 3.25 106-350F.81 3.50 1.06 3.50 125-100F 1.00 1.00 1.00 125-125F 1.00 1.25 1.25 1.25 125-150F 1.00 1.50 1.25 1.50 125-175F 1.00 1.75 1.25 1.75 125-200F 1.00 2.00 1.25 2.00 125-225F 1.00 2.25 1.25 2.25 125-250F 1.00 2.50 1.25 2.50 125-275F 1.00 2.75 1.25 2.75 125-300F 1.25 1.00 1.00 3.00 1.25 1.12.50 3.00 3/4 16 3/8 16 125-325F 1.00 3.25 1.25 3.25 125-350F 1.00 3.50 1.25 3.50 125-375F 1.00 3.75 1.25 3.75 125-400F 1.00 4.00 1.25 4.00 125-450F 1.00 4.50 1.25 4.50 125-500F 1.00 5.00 1.25 5.00 125-550F 1.00 5.50 1.25 5.50 125-600F 1.00 6.00 1.25 6.00 162-100F 1.00 1.25 162-125F 1.25 1.50 162-150F 1.25 1.50 1.62 1.75 162-175F 1.25 1.75 1.62 2.00 162-200F 1.25 2.00 1.62 2.25 162-225F 1.25 2.25 1.62 2.50 1.62 1.25 1.12.50 7/8 14 1/2 13 162-250F 1.25 2.50 1.62 2.75 162-275F 1.25 2.75 1.62 3.00 162-300F 1.25 3.00 1.62 3.25 162-325F 1.25 3.25 1.62 3.50 162-350F 1.25 3.50 1.62 3.75 162-375F 1.25 3.75 1.62 4.00 ASSEMBLY INCLUDES: Retainer Body Socket Head Cap Screws Socket Set Screw LOAD F RADIUS RATING NO. (in) (in) lbs. 100-XXX.625.03 1,500 106-XXX.690.03 1,500 125-XXX.875.03 3,000 162-XXX 1.125.06 5,000 187-XXX 1.250.06 7,500 200-XXX 1.375.06 10,000 Diam. Diam. Length ±.005 NO. (in) D2 (in) (in) L2 (in) L3 (in) L4 (in) S1 (in) S2 (in)) 162-400F 4.00 4.25 162-450F 4.50 4.75 162-500F 1.62 1.25 5.00 1.12.50 5.25 7/8 14 1/2 13 162-550F 5.50 6.00 162-600F 6.00 6.50 187-125F 1.25 1.50 187-150F 1.50 1.75 187-175F 1.75 1.87 2.00 187-200F 2.00 1.87 2.25 187-225F 2.25 1.87 2.50 187-250F 2.50 1.87 2.75 187-275F 2.75 1.87 3.00 187-300F 1.87 1.50 3.00 1.87 1.25.50 3.25 187-325F 3.25 1.87 3.50 1-1/8 12 5/8 11 187-350F 3.50 1.87 3.75 187-375F 3.75 1.87 4.00 187-400F 4.00 1.87 4.25 187-450F 4.50 1.87 5.00 187-500F 5.00 1.87 5.50 187-550F 5.50 1.87 6.00 187-600F 6.00 1.87 6.50 200-150F 1.50 2.00 200-175F 1.75 2.00 2.25 200-200F 2.00 2.00 2.50 200-225F 2.25 2.00 2.75 200-250F 2.50 2.00 3.00 200-275F 2.75 2.00 3.25 200-300F 3.00 2.00 3.50 200-325F 2.00 1.62 3.25 2.00 1.38.50 3.75 1-1/4 12 3/4 10 200-350F 3.50 2.00 4.00 200-375F 3.75 2.00 4.25 200-400F 4.00 2.00 4.50 200-450F 4.50 2.00 5.00 200-500F 5.00 2.00 5.50 200-550F 5.50 2.00 6.00 200-600F 6.00 2.00 6.50 45

PAD RETAINERS LOCKING INCH, REVERSE MOUNT, WITH FLATS Pad retainers are manufactured from 1144 steel and hardened to 28-34 Rockwell C-scale. They are machined to precise tolerances in order to retain the pad and assure parallelism during use. LOAD F RADIUS RATING NO. (in) (in) lbs. 100-XXXR.625.03 1,500 106-XXXR.690.03 1,500 125-XXXR.875.03 3,000 162-XXXR 1.125.06 5,000 187-XXXR 1.250.06 7,500 200-XXXR 1.375.06 10,000 46 Diam. Diam. Length ±.005 NO. (in) D2 (in) (in) G (in) L3 (in) T1 (in) 100-100R 1.00 100-125R 1.25 100-150R 1.50 100-175R 1.75 100-200R 2.00 100-225R 2.25 100-250R 2.50 100-275R 2.75 1.00.75 100-300R 3.00.625.38 5/16 18 100-350R 3.50 100-375R 3.75 100-400R 4.00 100-450R 4.50 100-500R 5.00 100-550R 5.50 100-600R 6.00 106-100R 1.00 1.06 106-125R.81 1.25 1.06 106-150R.81 1.50 1.06 106-175R.81 1.75 1.06 106-200R.81 2.00 1.06 106-225R 1.06.81.81 2.25 1.06.625.38 5/16 18 106-250R.81 2.50 1.06 106-275R.81 2.75 1.06 106-300R.81 3.00 1.06 106-325R.81 3.25 1.06 106-350R.81 3.50 1.06 125-100R 1.00 125-125R 1.00 1.25 1.25 125-150R 1.00 1.50 1.25 125-175R 1.00 1.75 1.25 125-200R 1.00 2.00 1.25 125-225R 1.00 2.25 1.25 125-250R 1.00 2.50 1.25 125-275R 1.00 2.75 1.25 125-300R 1.00 1.25 1.00 3.00 1.25.750.50 3/8 16 125-325R 1.00 3.25 1.25 125-350R 1.00 3.50 1.25 125-375R 1.00 3.75 1.25 125-400R 1.00 4.00 1.25 125-450R 1.00 4.50 1.25 125-500R 1.00 5.00 1.25 125-550R 1.00 5.50 1.25 125-600R 1.00 6.00 1.25 Diam. Diam. Length NO. ±.005 (in) D2 (in) (in) G (in) L3 (in) T1 (in) 162-125R 1.25 162-150R 1.25 1.50 1.62 162-175R 1.25 1.75 1.62 162-200R 1.25 2.00 1.62 162-225R 1.25 2.25 1.62 162-250R 1.25 2.50 1.62 162-275R 1.25 2.75 1.62 162-300R 1.25 3.00 1.62 1.62 1.25 1.000 162-325R 1.25 3.25 1.62.50 1/2 13 162-350R 1.25 3.50 1.62 162-375R 1.25 3.75 1.62 162-400R 1.25 4.00 1.62 162-450R 1.25 4.50 1.62 162-500R 1.25 5.00 1.62 162-550R 1.25 5.50 1.62 162-600R 1.25 6.00 1.62 187-150R 1.50 187-175R 1.50 1.75 1.87 187-200R 1.50 2.00 1.87 187-225R 1.50 2.25 1.87 187-250R 1.50 2.50 1.87 187-275R 1.50 1.87 1.50 2.75 1.250 1.87.50 5/8 11 187-300R 1.50 3.00 1.87 187-325R 1.50 3.25 1.87 187-350R 1.50 3.50 1.87 187-375R 1.50 3.75 1.87 187-400R 1.50 4.00 1.87 187-450R 1.50 4.50 187-500R 1.50 5.00 1.87 187-550R 1.50 5.50 1.87 187-600R 1.50 6.00 1.87 200-175R 1.75 200-200R 1.62 2.00 2.00 200-225R 1.62 2.25 2.00 200-250R 1.62 2.50 2.00 200-275R 1.62 2.00 1.62 2.75 1.500 2.00.50 3/4 10 200-300R 1.62 3.00 2.00 200-325R 1.62 3.25 2.00 200-350R 1.62 3.50 2.00 200-375R 1.62 3.75 2.00 200-400R 1.62 4.00 2.00 200-450R 1.62 4.50 2.00 200-500R 1.62 5.00 2.00 200-550R 1.62 5.50 2.00 200-600R 1.62 6.00 2.00

PAD RETAINERS STANDARD AND REVERSE MOUNT METRIC Pad retainers are manufactured from 1144 steel and hardened to 28-34 Rockwell C-scale. They are machined to precise tolerances in order to retain the pad and assure parallelism during use. S1 Socket Set Screw S2 Socket Head Cap Screw D2 L2 L3 S1 S2 LOAD RATING D2 L3 LOAD RATING NR50 50 40 35 15 M27 x 2 M16 x 2.0 192 kn NR70 70 60 40 15 M36 x 3 M20 x 2.5 299 kn NR50 50 40 NR70 70 60 15 15 192 kn 299 kn STANDARD MOUNT REVERSE MOUNT Diameter Length Diameter D2 (mm) (mm) (mm) NR50-30 30 NR50-40 40 40 50 NR50-45 40 45 50 NR50-50 40 50 50 NR50-60 40 60 50 NR50-65 40 65 50 NR50-70 40 70 50 40 50 NR50-75 40 75 50 NR50-90 40 90 50 NR50-100 100 NR50-115 40 115 50 NR50-130 40 130 50 NR50-140 40 140 50 NR50-160 160 NR70-40 40 NR70-45 60 45 70 NR70-50 60 50 70 NR70-60 60 60 70 NR70-65 60 65 70 NR70-70 60 70 70 NR70-75 60 75 70 NR70-90 60 90 70 NR70-100 60 100 70 NR70-115 60 115 70 NR70-130 60 130 70 NR70-140 60 140 70 NR70-160 160 Diameter Length Diameter D2 (mm) (mm) (mm) NR50-30R 30 NR50-40R 40 40 50 NR50-45R 40 45 50 NR50-50R 40 50 50 NR50-60R 40 60 50 NR50-65R 40 65 50 NR50-70R 40 70 50 40 50 NR50-75R 40 75 50 NR50-90R 40 90 50 NR50-100R 100 NR50-115R 40 115 NR50-130R 130 NR50-140R 40 140 50 NR50-160R 160 NR70-40R 40 NR70-45R 60 45 70 NR70-50R 60 50 70 NR70-60R 60 60 70 NR70-65R 60 65 70 NR70-70R 60 70 70 NR70-75R 60 75 70 NR70-90R 60 90 70 NR70-100R 60 100 70 NR70-115R 60 115 70 NR70-130R 60 130 70 NR70-140R 60 140 70 NR70-160R 160 47

www.danly.com TRUSTED SOLUTIONS AND INNOVATION PINS & BUSHINGS INCH

PINS & BUSHINGS CONTENTS www.danly.com General Information PAGE Plain Bearing Guide Posts Removable Precision Guide Posts 1 Press Fit Commercial & Precision Guide Posts 2 Demountable Commercial & Precision Guide Posts 4 Oversize Shoulder Press Fit Guide Posts 6 Plain Bearing Bushings Demountable Low Profile Bronze-Plated Bushings 7 Demountable Bronze, Bronze-Plated & Steel Bushings (Extra Long, Standard and Short Shoulder Series) 8 Demountable Self-Lubricating Bushings 10 Oversize Shoulder Demountable Bushings 12 Press Fit Bushings 13 Mold/Machinery Press Fit Straight Bushings 14 Mold Components Self-Lubricating Shoulder Bushings 15 Mold Components - Self-Lubricating Ejector Bushings 16 Ball Bearing Components Ball Bearing Cages 17 Ball Bearing Demountable Guide Posts 18 Ball Bearing Press Fit Guide Posts 20 Ball Bearing Demountable Bushings 21 Ball Bearing Straight Sleeve Bushings 22 Bosses Demountable Bosses 23 Selection Guides Ball Bearing Components Selection Guide 24 Type I Component Selection Guide 25 Type II & III Component Selection Guide 27 Type II & III Bushing & Ball Cage Selection Guide 28 Technical Information Ball Bearing Components Technical Information 30 Plain Bearing Components Technical Information 31 Clamp Dimensions for Demountable Posts and Bushings 32 ii i

www.danly.com General Information As the premier die set manufacturer, we offer a complete line of catalog die sets as well as custom complex and simple sets. For replacement parts and for those customers wanting to assemble their own sets, an extensive line of catalog guide posts and bushings in both plain bearing and ball bearing styles is available for immediate delivery. Our plain bearing guide posts are available in press fit, demountable and removable styles. The press fit and demountable styles are available in commercial and precision series. Precision guide posts are hardened, ground and hard chrome plated to provide an exceptionally smooth, hard wearing surface as well as providing resistance to corrosion, less friction and maintenance of close working fits. Our plain bearing bushings are available in press fit and demountable styles and are equipped with figure 8 oil grooves and lubrication fittings. Our demountable bushings are available in three profiles, standard, short and extra long shoulder to give optimum flexibility in die set design. The bushings are also available in steel, bronze, bronze-plated and self-lubricating materials and are ideally suited for running with commercial and precision posts. All demountable bushings are pre-fitted to the same diameter guide posts to ensure that the bushings and guide posts of the same diameter are completely interchangeable. Demountable posts and bushings are tap fit into location and seat flush with the ground face of the punch holder or die shoe. They are held in place with toe clamps and screws which provide perfect alignment of the post and bushing with the bore perpendicular to the ground surface of the punch holder or shoe. The clamp and screws provide four times the holding power compared to pressed-in components, yet they can be easily removed and assembled thus simplifying die building and maintenance. Our demountable bushings and guide posts provide ease of assembly. Demountable bushings are secured to the punch holder with our clamps and screws, proving four times the holding power of pressed-in bushings. Specially-designed spiral patterns are drilled into our ball cages to control tracking and grooving. Special equipment spins ball bearings in place, then our ball cages move on to rigid quality inspection. The ball bearing system includes press fit and demountable guide posts, press fit sleeve and demountable bushings as well as ball cages. The ball bearing guide posts are manufactured from hardened steel to assure free rolling of balls and high wear resistance. Each post is drilled and tapped at the bottom for mounting of the ball cage washer assembly. This unique mounting method permits the ball cage, except when under preload, to freely rotate 360 around the guide post thus eliminating scoring or tracking of the guide post surface. The ball bearings are arranged in the cage in a spiral pattern which also minimizes tracking or grooving and assures uniform wear. ii

Removable Precision Guide Posts Product Features Removable guide posts are easily assembled and disassembled and are designed for use in applications where it is desirable to sharpen the die while still mounted in the die set. The posts are installed into the die set and locked into place with a steel taper lock pin. The lock pin can be driven out for easy post removal. Removable posts have a microme finish and are ideally suited for running with steel, bronze or self-lubricating bushings. They are manufactured from high quality hardened steel and finish ground for a high precision finish. The hard chrome finish provides an exceptionally smooth, hard wearing surface thus reducing friction between the post and bearing. Utilizing the microme guide posts will greatly improve the accuracy and working life of die sets as well as provide additional corrosion resistance. 5-0820-4 NOTES: All removable guide posts are shipped with taper pin. Post Diameter A Length L Precision (in) (in) Part Number 1 4 5-0816-4 1 4 1/4 5-0817-4 1 4 1/2 5-0818-4 1 4 3/4 5-0819-4 1 5 5-0820-4 1 5 1/4 5-0821-4 1 5 1/2 5-0822-4 1 1 5 3/4 5-0823-4 1 6 5-0824-4 1 6 1/2 5-0826-4 1 7 5-0828-4 1 7 1/2 5-0830-4 1 8 5-0832-4 1 8 1/2 5-0834-4 1 9 5-0836-4 1 1/4 4 1/2 5-1018-4 1 1/4 4 3/4 5-1019-4 1 1/4 5 5-1020-4 1 1/4 5 1/4 5-1021-4 11/4 1/4 5 1/2 5-1022-4 1 1/4 5 3/4 5-1023-4 1 1/4 6 5-1024-4 1 1/4 6 1/2 5-1026-4 1 1/4 7 5-1028-4 Post Diameter A Length L Precision (in) (in) Part Number 1 1/4 7 1/2 5-1030-4 1 1/4 8 5-1032-4 1 1/4 8 1/2 5-1034-4 11/4 1/4 9 5-1036-4 1 1/4 10 5-1040-4 1 1/4 11 5-1044-4 1 1/4 12 5-1048-4 1 1/2 4 1/2 5-1218-4 1 1/2 4 3/4 5-1219-4 1 1/2 5 5-1220-4 1 1/2 5 1/4 5-1221-4 1 1/2 5 1/2 5-1222-4 1 1/2 5 3/4 5-1223-4 1 1/2 6 5-1224-4 1 1/2 6 1/2 5-1226-4 1 1/2 7 5-1228-4 1 1/2 7 1/2 5-1230-4 1 1/2 8 5-1232-4 1 1/2 8 1/2 5-1234-4 1 1/2 9 5-1236-4 1 1/2 10 5-1240-4 1 1/2 11 5-1244-4 1 1/2 12 5-1248-4 1 3/4 6 5-1424-4 Post Diameter A Length L Precision (in) (in) Part Number 1 3/4 6 1/2 5-1426-4 1 3/4 7 5-1428-4 1 3/4 7 1/2 5-1430-4 1 3/4 8 5-1432-4 1 3/4 3/4 8 1/2 5-1434-4 1 3/4 9 5-1436-4 1 3/4 10 5-1440-4 1 3/4 11 5-1444-4 1 3/4 12 5-1448-4 1 3/4 14 5-1456-4 2 6 5-1624-4 2 6 1/2 5-1626-4 2 7 5-1628-4 2 7 1/2 5-1630-4 2 8 5-1632-4 2 8 1/2 5-1634-4 2 9 5-1636-4 2 10 5-1640-4 2 11 5-1644-4 2 12 5-1648-4 2 13 5-1652-4 2 14 5-1656-4 2 17 5-1668-4 2 20 5-1680-4 1

Press Fit Commercial and Precision Guide Posts 5-0820-5 Product Features Press fit guide posts are available in commercial and precision series. Both series are manufactured from high quality hardened steel and finish ground for a high precision finish and ideally suited for running with steel, bronze or self-lubricating bushings. The precision series has a hard chrome finish providing an exceptionally smooth, hard wearing surface thus reducing friction between the post and bearing. Utilizing the precision microme guide posts will greatly improve the accuracy and working life of die sets as well as provide additional corrosion resistance. Press Fit Dimensions Press fit Press fit Diameter A Diameter D Length C (in) (in) (in) 1/2 0.5017 1 1/8* 5/8 0.6267 1 1/8 3/4 0.752 1 1/8* 7/8 0.877 1 1/4 1 1.002 1 1/2 1 1/4 1.2525 1 3/4 1 1/2 1.5025 1 3/4-2** 1 3/4 1.7525 2 1/4 2 2.0025 2 1/2 2 1/2 2.503 3 1/2 3 3.003 3 1/2 NOTES: See page 31 for die set boring specifications. DIMENSIONS: *C = 1" for 5-0414-1, 5-0614-1 & 5-0614-5 **C = 1 ¾" for part numbers where L is less than or equal to 7", C=2" for part numbers where L=7 ½" or greater Diameter Length Precision Commercial A (in) L (in) Part Number Part Number 1/2 3 1/2 5-0414-1 1/2 4 5-0416-1 1/2 4 1/4 5-0417-1 1/2 4 1/2 5-0418-1 1/2 1/2 4 3/4 5-0419-1 1/2 5 5-0420-1 1/2 5 1/4 5-0421-1 1/2 5 1/2 5-0422-1 5/8 4 5-0516-1 5/8 4 1/4 5-0517-1 5/8 4 1/2 5-0518-1 5/8 4 3/4 5-0519-1 5/8 5 5-0520-1 5/8 5 1/2 5-0522-1 5/8 6 5-0524-1 3/4 3 1/2 5-0614-1 5-0614-5 3/4 4 5-0616-1 5-0616-5 3/4 4 1/4 5-0617-1 5-0617-5 3/4 4 1/2 5-0618-1 5-0618-5 3/4 3/4 4 3/4 5-0619-1 5-0619-5 3/4 5 5-0620-1 5-0620-5 3/4 5 1/2 5-0622-1 5-0622-5 3/4 6 5-0624-1 5-0624-5 3/4 7 5-0628-5 3/4 8 5-0632-5 7/8 4 5-0716-1 5-0716-5 7/8 4 1/4 5-0717-1 5-0717-5 7/8 4 1/2 5-0718-1 5-0718-5 7/8 4 3/4 5-0719-1 5-0719-5 7/8 5 5-0720-1 5-0720-5 7/8 5 1/4 5-0721-1 5-0721-5 7/8 7/8 5 1/2 5-0722-1 5-0722-5 7/8 5 3/4 5-0723-1 5-0723-5 7/8 6 5-0724-1 5-0724-5 7/8 6 1/2 5-0726-1 5-0726-5 7/8 7 5-0728-1 5-0728-5 7/8 7 1/2 5-0730-1 5-0730-5 7/8 8 5-0732-1 5-0732-5 2

Press Fit Commercial and Precision Guide Posts Diameter Length Precision Commercial A (in) L (in) Part Number Part Number 1 4 5-0816-1 5-0816-5 1 4 1/4 5-0817-1 5-0817-5 1 4 1/2 5-0818-1 5-0818-5 1 4 3/4 5-0819-1 5-0819-5 1 5 5-0820-1 5-0820-5 1 5 1/4 5-0821-1 5-0821-5 1 5 1/2 5-0822-1 5-0822-5 1 5 3/4 5-0823-1 5-0823-5 6 5-0824-1 5-0824-5 1 1 6 1/2 5-0826-1 5-0826-5 1 7 5-0828-1 5-0828-5 1 7 1/2 5-0830-1 5-0830-5 1 8 5-0832-1 5-0832-5 1 8 1/2 5-0834-1 5-0834-5 1 9 5-0836-1 5-0836-5 1 10 5-0840-1 5-0840-5 1 11 5-0844-1 5-0844-5 1 12 5-0848-1 5-0848-5 1 1/4 4 1/2 5-1018-1 5-1018-5 1 1/4 4 3/4 5-1019-1 5-1019-5 1 1/4 5 5-1020-1 5-1020-5 1 1/4 5 1/4 5-1021-1 5-1021-5 1 1/4 5 1/2 5-1022-1 5-1022-5 1 1/4 5 3/4 5-1023-1 5-1023-5 1 1/4 6 5-1024-1 5-1024-5 1/4 6 1/2 5-1026-1 5-1026-5 1 1/4 1 1/4 7 5-1028-1 5-1028-5 1 1/4 7 1/2 5-1030-1 5-1030-5 1 1/4 8 5-1032-1 5-1032-5 1 1/4 8 1/2 5-1034-1 5-1034-5 1 1/4 9 5-1036-1 5-1036-5 1 1/4 10 5-1040-1 5-1040-5 1 1/4 11 5-1044-1 5-1044-5 1 1/4 12 5-1048-1 5-1048-5 1 1/2 4 1/2 5-1218-1 5-1218-5 1 1/2 4 3/4 5-1219-1 5-1219-5 1 1/2 5 5-1220-1 5-1220-5 1 1/2 5 1/4 5-1221-1 5-1221-5 1 1/2 5 1/2 5-1222-1 5-1222-5 1 1/2 5 3/4 5-1223-1 5-1223-5 1 1/2 6 5-1224-1 5-1224-5 1 1/2 6 1/2 5-1226-1 5-1226-5 1 1/2 7 5-1228-1 5-1228-5 1 1/2 7 1/2 5-1230-1 5-1230-5 1 1/2 8 5-1232-1 5-1232-5 1 1/2 8 1/2 5-1234-1 5-1234-5 1 1/2 9 5-1236-1 5-1236-5 1 1/2 10 5-1240-1 5-1240-5 1 1/2 11 5-1244-1 5-1244-5 1 1/2 12 5-1248-1 5-1248-5 1 1/2 13 5-1252-5 1 1/2 14 5-1256-5 1 1/2 15 5-1260-5 Diameter Length Precision Commercial A (in) L (in) Part Number Part Number 1 3/4 6 5-1424-1 5-1424-5 1 3/4 6 1/2 5-1426-1 5-1426-5 1 3/4 7 5-1428-1 5-1428-5 1 3/4 7 1/2 5-1430-1 5-1430-5 1 3/4 8 5-1432-1 5-1432-5 1 3/4 8 1/2 5-1434-1 5-1434-5 1 3/4 9 5-1436-1 5-1436-5 1 3/4 10 5-1440-1 5-1440-5 1 3/4 11 5-1444-1 5-1444-5 1 3/4 12 5-1448-1 5-1448-5 1 3/4 14 5-1456-1 5-1456-5 2 6 5-1624-1 5-1624-5 2 6 1/2 5-1626-1 5-1626-5 2 7 5-1628-1 5-1628-5 2 7 1/2 5-1630-1 5-1630-5 2 8 5-1632-1 5-1632-5 2 8 1/2 5-1634-1 5-1634-5 2 9 5-1636-1 5-1636-5 2 10 5-1640-1 5-1640-5 2 11 5-1644-1 5-1644-5 2 12 5-1648-1 5-1648-5 2 13 5-1652-1 5-1652-5 2 14 5-1656-1 5-1656-5 2 17 5-1668-1 5-1668-5 2 20 5-1680-1 5-1680-5 2 1/2 8 5-2032-1 5-2032-5 2 1/2 8 1/2 5-2034-1 5-2034-5 2 1/2 9 5-2036-1 5-2036-5 2 1/2 10 5-2040-1 5-2040-5 2 1/2 11 5-2044-1 5-2044-5 2 1/2 1/2 12 5-2048-1 5-2048-5 2 1/2 13 5-2052-1 5-2052-5 2 1/2 14 5-2056-1 5-2056-5 2 1/2 17 5-2068-1 5-2068-5 2 1/2 20 5-2080-1 5-2080-5 3 8 5-2432-1 5-2432-5 3 8 1/2 5-2434-1 5-2434-5 3 9 5-2436-1 5-2436-5 3 10 5-2440-1 5-2440-5 3 11 5-2444-1 5-2444-5 3 12 5-2448-1 5-2448-5 3 13 5-2452-1 5-2452-5 3 14 5-2456-1 5-2456-5 3 17 5-2468-1 5-2468-5 3 20 5-2480-1 5-2480-5 3

Demountable Commercial and Precision Guide Posts 5-0820-6 Product Features Press fit guide posts are manufactured from high quality hardened steel and finish ground for a high precision finish and ideally suited for running with steel, bronze or self-lubricating bushings. The precision series has a hard chrome finish providing an exceptionally smooth, hard wearing surface thus reducing friction between the post and bearing. Utilizing the precision microme guide posts will greatly improve the accuracy and working life of die sets as well as provide additional corrosion resistance. Demountable posts are tap fit and held in place with toe clamps and screws. They can be removed and assembled multiple times without damaging or distorting the mounting holes in the die set thus simplifying die building and maintenance. Demountable posts are also used to replace press fit posts when the press fit hole has been damaged and the straight pin no longer fits securely in the hole. NOTES: All demountable guide posts are supplied with mounting clamps and screws. See pages 32 & 33 for clamping dimensions or to order additional toe clamps or mounting screws. Length of post must be specified from shoulder, not overall length. Add thickness of die holder to F dimension to find L dimension of assembled set. Dimension X is the minimum distance between inside surface of shoe and holder with bushing shoulder resting on screw head. The dimension varies with shoulder and short shoulder bushings. Post Shoulder Shoulder Press Fit Minimum Shut Height X (in) Diameter A Diameter B Length D Length E Bushing Style (in) (in) (in) (in) Shoulder Short Shoulder 7/8 1 3/16 0.193 15/16 2 23/64 1 27/64 1 1 5/16 0.193 1 3/16 2 23/64 1 27/64 1 1/4 1 9/16 0.250 1 3/16 2 3/4 1 9/16 1 1/2 1 7/8 0.250 1 9/16 2 3/4 1 9/16 1 3/4 2 1/4 0.250 1 11/16 2 3/4 1 3/4 2 2 1/2 0.250 1 15/16 2 3/4 1 3/4 2 1/2 3 1/32 0.250 1 15/16 3 1/4 1 3/4 3 3 1/2 0.250 2 7/16 3 1/4 1 3/4 4

Demountable Commercial and Precision Guide Posts Diameter Working A Length F Precision Commercial (in) (in) Part Number Part Number 7/8 2 3/4 5-0711-6 5-0711-7 7/8 3 5-0712-6 5-0712-7 7/8 3 1/4 5-0713-6 5-0713-7 7/8 3 1/2 5-0714-6 5-0714-7 7/8 3 3/4 5-0715-6 5-0715-7 7/8 4 5-0716-6 5-0716-7 7/8 4 1/4 5-0717-6 5-0717-7 7/8 4 1/2 5-0718-6 5-0718-7 7/8 4 3/4 5-0719-6 5-0719-7 7/8 5 1/4 5-0721-6 5-0721-7 7/8 5 3/4 5-0723-6 5-0723-7 7/8 6 1/4 5-0725-6 5-0725-7 7/8 6 3/4 5-0727-6 5-0727-7 1 2 1/2 5-0810-6 5-0810-7 1 2 3/4 5-0811-6 5-0811-7 1 3 5-0812-6 5-0812-7 1 3 1/4 5-0813-6 5-0813-7 1 3 1/2 5-0814-6 5-0814-7 1 3 3/4 5-0815-6 5-0815-7 1 4 5-0816-6 5-0816-7 1 4 1/4 5-0817-6 5-0817-7 1 4 1/2 5-0818-6 5-0818-7 1 5 5-0820-6 5-0820-7 1 5 1/2 5-0822-6 5-0822-7 1 6 5-0824-6 5-0824-7 1 6 1/2 5-0826-6 5-0826-7 1 7 5-0828-6 5-0828-7 1 7 1/2 5-0830-6 5-0830-7 1 1/4 2 3/4 5-1011-6 5-1011-7 1 1/4 3 5-1012-6 5-1012-7 1 1/4 3 1/4 5-1013-6 5-1013-7 1 1/4 3 1/2 5-1014-6 5-1014-7 1 1/4 3 3/4 5-1015-6 5-1015-7 1 1/4 4 5-1016-6 5-1016-7 1 1/4 4 1/4 5-1017-6 5-1017-7 1 1/4 4 3/4 5-1019-6 5-1019-7 1 1/4 1 1/4 5 1/4 5-1021-6 5-1021-7 1 1/4 5 3/4 5-1023-6 5-1023-7 1 1/4 6 1/4 5-1025-6 5-1025-7 1 1/4 6 3/4 5-1027-6 5-1027-7 1 1/4 7 1/4 5-1029-6 5-1029-7 1 1/4 8 1/4 5-1033-6 5-1033-7 1 1/4 9 1/4 5-1037-6 5-1037-7 1 1/4 10 1/4 5-1041-6 5-1041-7 1 1/2 2 3/4 5-1211-6 5-1211-7 1 1/2 3 5-1212-6 5-1212-7 1 1/2 3 1/4 5-1213-6 5-1213-7 1 1/2 3 1/2 5-1214-6 5-1214-7 1 1/2 1/2 3 3/4 5-1215-6 5-1215-7 1 1/2 4 5-1216-6 5-1216-7 1 1/2 4 1/4 5-1217-6 5-1217-7 1 1/2 4 3/4 5-1219-6 5-1219-7 Diameter Working A Length F Precision Commercial (in) (in) Part Number Part Number 1 1/2 5 1/4 5-1221-6 5-1221-7 1 1/2 5 3/4 5-1223-6 5-1223-7 1 1/2 6 1/4 5-1225-6 5-1225-7 1 1/2 6 3/4 5-1227-6 5-1227-7 1 1/2 1/2 7 1/4 5-1229-6 5-1229-7 1 1/2 8 1/4 5-1233-6 5-1233-7 1 1/2 9 1/4 5-1237-6 5-1237-7 1 1/2 10 1/4 5-1241-6 5-1241-7 1 3/4 3 1/2 5-1414-6 5-1414-7 1 3/4 4 5-1416-6 5-1416-7 1 3/4 4 1/2 5-1418-6 5-1418-7 1 3/4 5 5-1420-6 5-1420-7 1 3/4 5 1/2 5-1422-6 5-1422-7 1 3/4 6 5-1424-6 5-1424-7 1 3/4 6 1/2 5-1426-6 5-1426-7 1 3/4 7 1/2 5-1430-6 5-1430-7 1 3/4 8 1/2 5-1434-6 5-1434-7 1 3/4 9 1/2 5-1438-6 5-1438-7 1 3/4 11 1/2 5-1446-6 5-1446-7 2 3 1/2 5-1614-6 5-1614-7 2 4 5-1616-6 5-1616-7 2 4 1/2 5-1618-6 5-1618-7 2 5 5-1620-6 5-1620-7 2 5 1/2 5-1622-6 5-1622-7 2 6 5-1624-6 5-1624-7 6 1/2 5-1626-6 5-1626-7 2 7 1/2 5-1630-6 5-1630-7 2 8 1/2 5-1634-6 5-1634-7 2 9 1/2 5-1638-6 5-1638-7 2 10 1/2 5-1642-6 5-1642-7 2 11 1/2 5-1646-6 5-1646-7 2 14 1/2 5-1658-6 5-1658-7 2 17 1/2 5-1670-6 5-1670-7 2 1/2 4 1/2 5-2018-6 5-2018-7 2 1/2 5 5-2020-6 5-2020-7 2 1/2 5 1/2 5-2022-6 5-2022-7 2 1/2 6 1/2 5-2026-6 5-2026-7 2 1/2 7 1/2 5-2030-6 5-2030-7 2 1/2 1/2 8 1/2 5-2034-6 5-2034-7 2 1/2 9 1/2 5-2038-6 5-2038-7 2 1/2 10 1/2 5-2042-6 5-2042-7 2 1/2 13 1/2 5-2054-6 5-2054-7 2 1/2 16 1/2 5-2066-6 5-2066-7 3 4 1/2 5-2418-6 5-2418-7 3 5 5-2420-6 5-2420-7 3 5 1/2 5-2422-6 5-2422-7 3 6 1/2 5-2426-6 5-2426-7 3 7 1/2 5-2430-6 5-2430-7 3 8 1/2 5-2434-6 5-2434-7 3 9 1/2 5-2438-6 5-2438-7 3 10 1/2 5-2442-6 5-2442-7 3 13 1/2 5-2454-6 5-2454-7 3 16 1/2 5-2466-6 5-2466-7 5

Oversize Shoulder Press Fit Guide Posts Product Features These oversize shoulder guide posts are manufactured from high quality hardened steel and often used with oversize shoulder bushings shown on page 12. The press fit diameters of these posts are the same as the press fit of the outside diameters of the oversize shoulder bushings, thus the same hole may be bored through the punch and die holder. The press fit diameters are 0.0075" oversize to allow grinding stock to fit the bored hole. 5-0820-3 Post Press Fit Press Fit Working Overall Commercial Diameter A Diameter B Length C Length D Length L Part (in) (in) (in) (in) (in) Number** 1 1 1/2 1 1/2 3 4 1/2 5-0818-3 1 1 1/2 1 1/2 3 1/2 5 5-0820-3 1 1 1/2 1 1/2 4 5 1/2 5-0822-3 1/2 1/2 4 1/2 6 5-0824-3 1 1 1/2 1 1/2 1 1/2 1 1/2 5 6 1/2 5-0826-3 1 1 1/2 1 1/2 5 1/2 7 5-0828-3 1 1 1/2 1 1/2 6 7 1/2 5-0830-3 1 1 1/2 1 1/2 6 1/2 8 5-0832-3 1 1/4 1 3/4 2 3 5 5-1020-3 1 1/4 1 3/4 2 3 1/2 5 1/2 5-1022-3 1 1/4 1 3/4 2 4 6 5-1024-3 1 1/4 1 3/4 2 4 1/2 6 1/2 5-1026-3 1 1/4 1 3/4 2 5 7 5-1028-3 1 1/4 1 3/4 2 5 1/2 7 1/2 5-1030-3 1 1/4 1 3/4 2 6 8 5-1032-3 1 1/4 1 3/4 2 6 1/2 8 1/2 5-1034-3 1 1/4 1 3/4 2 7 9 5-1036-3 1 1/2 2 2 3/8 4 5/8 7 5-1228-3 1 1/2 2 2 3/8 5 1/8 7 1/2 5-1230-3 1 1/2 2 2 3/8 5 5/8 8 5-1232-3 1 1/2 2 2 3/8 6 1/8 8 1/2 5-1234-3 1 1/2 2 2 3/8 6 5/8 9 5-1236-3 1 1/2 2 2 3/8 7 1/8 9 1/2 5-1238-3 1 1/2 2 2 3/8 7 5/8 10 5-1240-3 1 3/4 2 1/4 2 7/8 4 5/8 7 1/2 5-1430-3 1 3/4 2 1/4 2 7/8 5 1/8 8 5-1432-3 3/4 1/4 7/8 5 5/8 8 1/2 5-1434-3 1 3/4 2 1/4 2 7/8 3/4 2 1/4 2 7/8 6 1/8 9 5-1436-3 1 3/4 2 1/4 2 7/8 6 5/8 9 1/2 5-1438-3 1 3/4 2 1/4 2 7/8 7 1/8 10 5-1440-3 2 2 1/2 3 3/8 4 5/8 8 5-1632-3 2 2 1/2 3 3/8 5 5/8 9 5-1636-3 1/2 3/8 6 5/8 10 5-1640-3 2 2 1/2 3 3/8 2 2 1/2 3 3/8 7 5/8 11 5-1644-3 2 2 1/2 3 3/8 8 5/8 12 5-1648-3 2 2 1/2 3 3/8 9 5/8 13 5-1652-3 2 1/2 3 1/4 3 7/8 5 1/8 9 5-2036-3 2 1/2 3 1/4 3 7/8 6 1/8 10 5-2040-3 1/2 1/4 7/8 7 1/8 11 5-2044-3 2 1/2 3 1/4 3 7/8 1/2 1/4 3 7/8 8 1/8 12 5-2048-3 2 1/2 3 1/4 3 7/8 9 1/8 13 5-2052-3 2 1/2 3 1/4 3 7/8 10 1/8 14 5-2056-3 **PLEASE NOTE The -3 Commercial Parts are not inventoried, but are available as a special. 6

Demountable Low Profile Bronze-Plated Bushings Product Features These bronze-plated low profile demountable bushings are designed so that the main body of the bushing is contained within the punch holder while only a minimum of the bushing projects below the punch holder and into the die area. With minimal bushing projection, this model is ideal for dies running in presses with automatic transfer devices. Since the bushings do not need removed during grinding, it is well suited for applications that require often die sharpening. All bushings are also equipped with oil grooves and lubrication fittings. Demountable bushings are tap fit into location and seat flush with the ground face of the punch holder. The bushings are held in place with toe clamps and screws which provide perfect alignment of the bushing with the bore perpendicular to the ground surface of the punch holder. The clamp and screws provide four times the holding power compared to pressed-in bushings, yet they can be easily removed and assembled thus simplifying die building and maintenance. 6-0807-27 NOTES: All demountable bushings are supplied with mounting clamps and screws. See pages 32 & 33 for clamping dimensions or to order additional toe clamps or mounting screws. Post Bushing Diameters Press Fit Shoulder Overall Bronze-Plated Diameter Length E Length F Length L Part A (in) B (in) C (in) C1 (in) (in) (in) (in) Number 1 1 1/2 1.845 1.593 7/8 1/2 1 3/8 6-0807-27 1 1 1/2 1.845 1.593 1 3/8 1/2 1 7/8 6-0811-27 1 1 1/2 1.845 1.593 2 3/8 1/2 2 7/8 6-0819-27 1 1/4 1 3/4 2.095 1.843 7/8 1/2 1 3/8 6-1007-27 1 1/4 1 3/4 2.095 1.843 1 7/8 1/2 2 3/8 6-1015-27 1 1/4 1 3/4 2.095 1.843 2 7/8 1/2 3 3/8 6-1023-27 1/2 2.345 2.062 1 7/8 1/2 2 3/8 6-1215-27 1 1/2 2 2.345 2.062 1/2 1 1/2 2 2.345 2.062 2 7/8 1/2 3 3/8 6-1223-27 3/4 1/4 2.658 2.312 2 3/8 1/2 2 7/8 6-1419-27 1 3/4 2 1/4 2.658 2.312 1/2 1 3/4 2 1/4 2.658 2.312 3 3/8 1/2 3 7/8 6-1427-27 1/2 3.064 2.625 2 3/8 1/2 2 7/8 6-1619-27 2 2 1/2 3.064 2.625 1/2 2 2 1/2 3.064 2.625 3 3/8 1/2 3 7/8 6-1627-27 2 1/2 3 3.814 3.062 2 5/8 1/2 3 1/8 6-2021-27 2 1/2 3 3.814 3.062 3 5/8 1/2 4 1/8 6-2029-27 2 1/2 3 3.814 3.062 4 5/8 1/2 5 1/8 6-2037-27 7

Demountable Bushings Bronze, Bronze-Plated & Steel 6-08-28 & 6-08-56 Product Features These demountable bushings are available in three profiles: standard, short and extra long shoulder to give optimum flexibility in die set design. The bushings are also available in steel, bronze and bronze-plated materials and are ideally suited for running with commercial and precision posts. All demountable bushings are prefitted to the same diameter guide posts to ensure that the bushings and guide posts of the same diameter are completely interchangeable. Demountable bushings are tap fit into location and seat flush with the ground face of the punch holder. The bushings are held in place with toe clamps and screws which provide perfect alignment of the bushing with the bore perpendicular to the ground surface of the punch holder. The clamp and screws provide four times the holding power compared to pressed-in bushings, yet they can be easily removed and assembled thus simplifying die building and maintenance. All bushings are equipped with figure 8 oil grooves and lubrication fittings. The bronze and bronze-plated demountable bushings offer superior resistance to seizure, the major cause of bushing wear. They are recommended in high speed applications and in applications with hide side thrust loads. EXTRA LONG SHOULDER Post Bushing Diameters Press Fit Shoulder Overall Steel Bronze Diameter Length E Length F Length L Part Plated Part A (in) B (in) C (in) C1(in) (in) (in) (in) Number Number 1 1 1/2 1.720 1.845 15/16 3 3 15/16 6-08-56 6-08-28 1 1/4 1 3/4 1.940 2.095 1 1/8 3 4 1/8 6-10-56 6-10-28 1 1/2 2 2.190 2.345 1 3/16 3 4 3/16 6-12-56 6-12-28 1 3/4 2 1/4 2.503 2.658 1 3/8 3 4 3/8 6-14-56 6-14-28 2 2 1/2 2.909 3.064 1 5/8 3 4 5/8 6-16-56 6-16-28 2 1/2 3 1/4 3.659 3.814 1 7/8 3 4 7/8 6-20-56 6-20-28 3 3 3/4 4.190 4.283 1 7/8 3 4 7/8 6-24-56 6-24-28 NOTES: All demountable bushings are supplied with mounting clamps and screws. See pages 32 & 33 for clamping dimensions or to order additional toe clamps or mounting screws. 8

Demountable Bushings Bronze, Bronze-Plated & Steel 6-08-64 & 6-08-48 STANDARD SHOULDER Post Bushing Diameters Press Fit Shoulder Overall Steel Bronze Bronze Diameter Length E Length F Length L Part Plated Part Part A (in) B (in) C (in) C1(in) (in) (in) (in) Number Number Number 3/4 1 1/8 1.175 1.300 11/16 1 3/4 2 7/16 6-06-64 7/8 1 3/8 1.422 1.547 11/16 1 3/4 2 7/16 6-07-64 1 1 1/2 1.720 1.845 15/16 1 3/4 2 11/16 6-08-64 6-08-24 6-08-48 1 1/4 1 3/4 1.940 2.095 1 1/8 2 3 1/8 6-10-64 6-10-24 6-10-48 1 1/2 2 2.190 2.345 1 3/16 2 3 3/16 6-12-64 6-12-24 6-12-48 1 3/4 2 1/4 2.503 2.658 1 3/8 2 3 3/8 6-14-64 6-14-24 6-14-48 2 2 1/2 2.909 3.064 1 5/8 2 3 5/8 6-16-64 6-16-24 6-16-48 2 1/2 3 1/4 3.659 3.814 1 7/8 2 1/2 4 3/8 6-20-64 6-20-24 6-20-48 3 3 3/4 4.190 4.283 1 7/8 2 1/2 4 3/8 6-24-64 6-24-24 6-24-48 6-08-23 & 6-08-63 SHORT SHOULDER Post Bushing Diameters Press Fit Shoulder Overall Steel Bronze Diameter Length E Length F Length L Part Plated Part A (in) B (in) C (in) C1(in) (in) (in) (in) Number Number 3/4 1 1/8 1.175 1.300 11/16 3/4 1 7/16 6-06-63 7/8 1 3/8 1.422 1.547 11/16 3/4 1 7/16 6-07-63 1 1 1/2 1.720 1.845 15/16 13/16 1 3/4 6-08-63 6-08-23 1 1/4 1 3/4 1.940 2.095 1 1/8 13/16 1 15/16 6-10-63 6-10-23 1 1/2 2 2.190 2.345 1 3/16 13/16 2 6-12-63 6-12-23 1 3/4 2 1/4 2.503 2.658 1 3/8 1 2 3/8 6-14-63 6-14-23 2 2 1/2 2.909 3.064 1 5/8 1 2 5/8 6-16-63 6-16-23 2 1/2 3 1/4 3.659 3.814 1 7/8 1 2 7/8 6-20-63 6-20-23 3 3 3/4 4.190 4.283 1 7/8 1 2 7/8 6-24-63 6-24-23 9

Demountable Self-Lubricating Bushings GS100-15G Product Features These demountable self-lubricating bushings are available in standard and short profiles and are ideally suited for running with commercial and precision posts. They are manufactured from cast aluminum bronze material and are prefitted to the same diameter guide posts to ensure that the bushings and guide posts of the same diameter are interchangeable. Self-lubricating bushings contain graphite plugs which are impregnated with oil. When the bushings reach 80-90 F as a result of friction between the bushing and guide post, oil is drawn from the plug thus lubricating the wear surface. A dark smear pattern is created on the wear surface as the oil and graphite are imbedded into the bronze or steel grain. This provides the lubrication necessary for continuous performance of the tool. Demountable bushings are tap fit into location and seat flush with the ground face of the punch holder. The bushings are held in place with toe clamps and screws which provide perfect alignment of the bushing with the bore perpendicular to the ground surface of the punch holder. The clamp and screws provide four times the holding power compared to pressed-in bushings, yet they can be easily removed and assembled thus simplifying die building and maintenance. SHORT SHOULDER Post Bushing Diameters Press Fit Shoulder Overall Self-Lubricating Diameter Length E Length F Length L Part A (in) B (in) C (in) C1 (in) (in) (in) (in) Number 1/2 1 9/16 1 3/4 1 3/8 1/2 1 7/8 GS100-15G 1 1 1/2 1 3/4 1 9/16 1/2 1 1/2 1 9/16 1 3/4 2 3/8 1/2 2 7/8 GS100-23G 1/4 3/4 1 15/16 2 1/8 1 7/8 1/2 2 3/8 GS125-19G 1 1/4 1 3/4 2 1/8 1 15/16 1/2 1/4 3/4 1 15/16 2 1/8 2 7/8 1/2 3 3/8 GS125-27G 1/2 1 3/16 2 3/8 1 7/8 1/2 2 3/8 GS150-19G 1 1/2 2 2 3/8 2 3/16 1/2 1/2 1 3/16 2 3/8 2 7/8 1/2 3 3/8 GS150-27G 3/4 1/4 2 7/16 2 5/8 2 3/8 1/2 2 7/8 GS175-23G 1 3/4 2 1/4 2 5/8 2 7/16 1/2 1 3/4 2 1/4 2 7/16 2 5/8 3 3/8 1/2 3 7/8 GS175-31G 1/2 2 3/4 2 15/16 2 3/8 1/2 2 7/8 GS200-23G 2 2 1/2 2 15/16 2 3/4 1/2 2 2 1/2 2 3/4 2 15/16 3 3/8 1/2 3 7/8 GS200-31G 2 1/2 3 1 3/16 3 3/8 2 5/8 3/8 3 GS250-24G 2 1/2 3 13 3/16 3/8 3 3/16 3/8 3 5/8 3/8 3/8 4 GS250-32G 2 1/2 3 1 3/16 3 3/8 4 5/8 3/8 5 GS250-40G 3 3 1/2 3 11/16 3 7/8 2 5/8 3/8 3 GS300-24G 1/2 3 11/16 3 7/8 3 5/8 3/8 4 GS300-32G 3 3 1/2 3 7/8 3 11/16 3/8 1/2 3 11/16 3 7/8 4 5/8 3/8 5 GS300-40G 3 3 1/2 3 11/16 3 7/8 5 5/8 3/8 6 GS300-48G 3 3/4 4 1/2 4 7/8 4 11/16 6 5/8 3/8 7 GS375-56G 4 1/2 5 1/2 5 11/16 5 7/8 4 5/8 3/8 5 GS450-40G 4 1/2 5 1/2 5 7/8 5 11/16 3/8 1/2 1/2 5 11/16 5 7/8 7 5/8 3/8 8 GS450-64G 10

Demountable Self-Lubricating Bushings G00 STANDARD SHOULDER Post Bushing Diameters Press Fit Shoulder Overall Self-Lubricating Diameter Length E Length F Length L Part A (in) B (in) C (in) C1 (in) (in) (in) (in) Number 1 1 1/2 1 3/4 1 27/32 15/16 1 3/4 2 11/16 G00 1 1/4 1 3/4 1 15/16 2 3/32 1 1/8 2 3 1/8 G25 1 1/2 2 2 3/16 2 11/32 1 3/16 2 3 3/16 G50 1 3/4 2 1/4 2 1/2 2 21/32 1 3/8 2 3 3/8 G75 2 2 1/2 2 29/32 3 1/16 1 5/8 2 3 5/8 GD200 2 1/2 3 1/4 3 21/32 3 13/16 1 7/8 2 1/2 4 3/8 GD250 3 3 3/4 4 3/16 4 9/32 1 7/8 2 1/2 4 3/8 GD300 NOTES: Until the lubrication process begins, a light 20 wt. oil should be applied to pre-lube the wear surface of the bushing. All demountable bushings are supplied with mounting clamps and screws. See pages 32 & 33 for clamping dimensions or to order additional toe clamps or mounting screws. 11

Oversize Shoulder Demountable Bushings NOTES: 6-08-21 & 6-08-25 All demountable bushings are supplied with mounting clamps and screws. See pages 32 & 33 for clamping dimensions or to order additional toe clamps or mounting screws. Product Features Oversize shoulder bushings are available in standard and short shoulder profiles and available in steel, bronze and bronze-plated materials. They are often used in special die sets in conjunction with oversize shoulder guide posts shown on page 6. The press fit diameters of these bushings are the same as the press fit of the outside diameters of the oversize shoulder posts, thus the same hole may be bored through the punch and die holder. The press fit diameters are 0.0075" oversize to allow grinding stock to fit the bored hole. The steel or bronze bushings may be ground for tap fit and installed with clamps and screws or may also be ground for a press fit. The bronze-plated bushings are for use as demountable bushings only and are supplied with the appropriate number of clamps and screws. These bushings should not be honed. If more clearance is desired, it is recommended to grind the working diameter of the shoulder guide post. **PLEASE NOTE The -21 Bronze Plated Parts are not inventoried, but are available as a special. SHORT SHOULDER STANDARD SHOULDER SHORT SHOULDER Post Bushing Diameters Press Fit Shoulder Overall Steel Bronze Diameter Length E Length F Length L Part Plated Part A (in) B (in) C (in) C1(in) (in) (in) (in) Number Number** 1 1 1/2 1.720 1.845 15/16 13/16 1 3/4 6-08-25 6-08-21 1 1/4 1 3/4 1.940 2.095 1 1/8 13/16 1 15/16 6-10-25 6-10-21 1 1/2 2 2.190 2.345 1 3/16 13/16 2 6-12-25 6-12-21 1 3/4 2 1/4 2.503 2.658 1 3/8 1 2 3/8 6-14-25 6-14-21 2 2 1/2 2.909 3.064 1 5/8 1 2 5/8 6-16-25 6-16-21 2 1/2 3 1/4 3.659 3.814 1 7/8 1 2 7/8 6-20-25 6-20-21 STANDARD SHOULDER Post Bushing Diameters Press Fit Shoulder Overall Steel Bronze Bronze Diameter Length E Length F Length L Part Plated Part Part A (in) B (in) C (in) C1(in) (in) (in) (in) Number Number Number 1 1 1/2 1.720 1.845 15/16 1 3/4 2 11/16 6-08-26 6-08-22 6-08-29 1 1 1/4 1 3/4 1.940 2.095 1 1/8 2 3 1/8 6-10-26 6-10-22 6-10-29 1 1 1/2 2 2.190 2.345 1 3/16 2 3 3/16 6-12-26 6-12-22 6-12-29 1 1 3/4 2 1/4 2.503 2.658 1 3/8 2 3 3/8 6-14-26 6-14-22 6-14-29 2 2 1/2 2.909 3.064 1 5/8 2 3 5/8 6-16-26 6-16-22 6-16-29 2 1/2 3 1/4 3.659 3.814 1 7/8 2 1/2 4 3/8 6-20-26 6-20-22 6-20-29 12

Press Fit Bushings Product Features These press fit bushings are available in short shoulder, short sleeve and long sleeve profiles. Manufactured from high quality hardened steel, the bushings are finish ground for a press fit. Bushings 1 ¾" in diameter and smaller are finish ground 0.0006" under listed inside diameters to allow for honing at assembly. Bushings with inside diameters 2" and larger are finished ground to decimal diameters. EXTRA LONG SLEEVE (-3) bushings include lubrication fitting and and grease grooves. SHORT SLEEVE (-1) bushings include grease grooves but do not have a lubrication fitting. 6-08-03 & 6-08-01 NOTE: The press fit bushings shown on this page must be honed to fit the guide post. These bushings are finished undersized on the inside diameter to allow for fitting of the guide post. If it is desired to receive these bushings honed to a finished inside diameter a -H must be entered at the end of the part number. EXAMPLE: 6-04-3-H to receive a bushing with an inside diameter that does not require additional fitting for guide post. Care still needs to be taken to not collapse the inside diameter of the bushing when pressing the bushing into a plate. EXTRA LONG SLEEVE SHORT SLEEVE Post Outside Overall Diameter A Diameter B Length L Part (in) (in) (in) Number 1/2 13/16 3 6-04-3 5/8 1 3 6-05-3 3/4 1 1/8 3 6-06-3 7/8 1 3/8 3 6-07-3 1 1 1/2 3 6-08-3 1 1/4 1 3/4 3 6-10-3 1 1/2 2 3 6-12-3 1 3/4 2 1/4 3 6-14-3 2 2 1/2 3 6-16-3 2 1/2 3 1/4 3 6-20-3 Post Outside Overall Diameter A Diameter B Length L Part (in) (in) (in) Number 1/2 13/16 1 1/2 6-04-1 5/8 1 1 1/2 6-05-1 3/4 1 1/8 1 3/4 6-06-1 7/8 1 3/8 1 3/4 6-07-1 1 1 1/2 1 3/4 6-08-1 1 1/4 1 3/4 2 6-10-1 1 1/2 2 2 6-12-1 SHORT SHOULDER Post Press Fit Bushing Press Fit Shoulder Overall Diameter A Diameter B Diameter C Length E Length F Length L Part (in) (in) (in) (in) (in) (in) Number 1/2 13/16 1.062 11/16 13/16 1 1/2 6-04-61 5/8 1 1.218 11/16 13/16 1 1/2 6-05-61 3/4 1 1/8 1.375 15/16 13/16 1 3/4 6-06-61 7/8 1 3/8 1.625 15/16 13/16 1 3/4 6-07-61 13

Mold/Machinery Press Fit Straight Bushings MS100-12 Product Features These press fit self-lubricating bushings are manufactured from high quality self lubricated aluminum bronze material and are ideally suited for running with commercial and precision posts. Self-lubricating bushings contain graphite plugs which are impregnated with oil. When the bushings reach 80-90 F as a result of friction between the bushing and guide post, oil is drawn from the plug thus lubricating the wear surface. A dark smear pattern is created on the wear surface as the oil and graphite are imbedded into the bronze or steel grain. This provides the lubrication necessary for continuous performance of the tool. NOTES: Until the lubrication process begins, a light 20 wt. oil should be applied to pre-lube the wear surface of the bushing. Guide Post Outside Overall Diameter A Diameter C Length L Part (in) (in) (in) Number 1.1255 7/8 MS750-7 3/4 1.1255 1 3/8 MS750-11 3/4 1.1255 1 1/2 MS750-12 7/8 1.2505 1 1/4 MS875-10 7/8 1.2505 7/8 1.2505 1 1/2 MS875-12 1 1.3755 1 1/4 MS100-10 1 1.3755 1 3/8 MS100-11 1.3755 1 1/2 MS100-12 1 1.3755 1 1.3755 1 3/4 MS100-14 1 1.3755 2 MS100-16 1 1.3755 3 MS100-24 1 1/4 1.6255 1 1/4 MS125-10 1 1/4 1.6255 1 3/8 MS125-11 1 1/4 1.6255 1 1/2 MS125-12 1 1/4 1.6255 1 3/4 MS125-14 1 1/4 1.6255 1 7/8 MS125-15 1 1/4 1.6255 2 MS125-16 1 1/4 1.6255 3 MS125-24 1 1/2 2.0005 1 1/4 MS150-10 1 1/2 2.0005 1 3/8 MS150-11 1 1/2 2.0005 1 1/2 MS150-12 1 1/2 2.0005 1 3/4 MS150-14 1 1/2 2.0005 1 7/8 MS150-15 1 1/2 2.0005 2 MS150-16 3 MS150-24 Guide Post Outside Overall Diameter A Diameter C Length L Part (in) (in) (in) Number 1 3/4 2.2505 1 1/4 MS175-10 1 3/4 2.2505 1 1/2 MS175-12 1 3/4 2.2505 1 3/4 MS175-14 1 3/4 3/4 2.2505 2 MS175-16 2.2505 1 3/4 2.2505 2 1/2 MS175-20 1 3/4 2.2505 3 MS175-24 1 3/4 2.2505 3 1/2 MS175-28 1 3/4 2.2505 4 MS175-32 2 2.5005 1 1/4 MS200-10 2 2.5005 1 1/2 MS200-12 2.5005 2 MS200-16 2 2.5005 2 2.5005 2 1/2 MS200-20 2 2.5005 3 MS200-24 2 2.5005 3 7/8 MS200-31 2 1/4 2.7505 1 1/2 MS225-12 1/4 2.7505 2 MS225-16 2 1/4 2.7505 2 1/4 2.7505 2 1/2 MS225-20 2 1/4 2.7505 3 MS225-24 2 1/2 3.2505 1 1/2 MS250-12 1/2 3.2505 2 MS250-16 2 1/2 3.2505 2 1/2 3.2505 3 MS250-24 2 1/2 3.2505 4 7/8 MS250-39 3 3.7505 2 MS300-16 3 3.7505 2 1/2 MS300-20 3 3.7505 3 MS300-24 3 3.7505 3 1/2 MS300-28 3 3.7505 4 7/8 MS300-39 14

Mold Components Self-Lubricating Shoulder Bushings Product Features These press fit self-lubricating bushings are manufactured from high quality self lubricated aluminum bronze material and are ideally suited for running with commercial and precision posts. Self-lubricating bushings contain graphite plugs which are impregnated with oil. When the bushings reach 80-90 F as a result of friction between the bushing and guide post, oil is drawn from the plug thus lubricating the wear surface. A dark smear pattern is created on the wear surface as the oil and graphite are imbedded into the bronze or steel grain. This provides the lubrication necessary for continuous performance of the tool. S1000-34G Post Press Fit Outside Press Fit Overall Self- Diameter Diameter Diameter Length Length Lubricating A (in) B (in) C (in) E (in) L (in) Part No. 3/4 1.1255 1.30 11/16 7/8 S750-7G 3/4 1.1255 1.30 1 3/16 1 3/8 S750-11G 3/4 1.1255 1.30 1 11/16 1 7/8 S750-15G 3/4 1.1255 1.30 2 3/16 2 3/8 S750-19G 3/4 1.1255 1.30 2 11/16 2 7/8 S750-23G 3/4 1.1255 1.30 3 3/16 3 3/8 S750-27G 3/4 1.1255 1.30 3 11/16 3 7/8 S750-31G 3/4 1.1255 1.30 4 3/16 4 3/8 S750-35G 3/4 1.1255 1.30 4 11/16 4 7/8 S750-39G 7/8 1.2505 1.43 11/16 7/8 S875-7G 7/8 1.2505 1.43 1 3/16 1 3/8 S875-11G 7/8 1.2505 1.43 1 11/16 1 7/8 S875-15G 7/8 1.2505 1.43 2 3/16 2 3/8 S875-19G 7/8 1.2505 1.43 7/8 1.2505 1.43 2 11/16 2 7/8 S875-23G 7/8 1.2505 1.43 3 3/16 3 3/8 S875-27G 7/8 1.2505 1.43 3 11/16 3 7/8 S875-31G 7/8 1.2505 1.43 4 3/16 4 3/8 S875-35G 1 1.3755 1.55 11/16 7/8 S1000-7G 1 1.3755 1.55 1 3/16 1 3/8 S1000-11G 1 1.3755 1.55 1 11/16 1 7/8 S1000-15G 1 1.3755 1.55 2 3/16 2 3/8 S1000-19G 1.3755 1.55 2 11/16 2 7/8 S1000-23G 1 1.3755 1.55 1 1.3755 1.55 3 3/16 3 3/8 S1000-27G 1 1.3755 1.55 3 11/16 3 7/8 S1000-31G 1 1.3755 1.55 4 3/16 4 3/8 S1000-35G 1 1.3755 1.55 4 11/16 4 7/8 S1000-39G 1 1.3755 1.55 5 11/16 5 7/8 S1000-47G 1 1/4 1.6255 1.80 11/16 7/8 S1250-7G 1 1/4 1.6255 1.80 1 3/16 1 3/8 S1250-11G 1 1/4 1.6255 1.80 1 11/16 1 7/8 S1250-15G 1/4 1.6255 1.80 2 3/16 2 3/8 S1250-19G 1 1/4 1.6255 1.80 1 1/4 1.6255 1.80 2 11/16 2 7/8 S1250-23G 1 1/4 1.6255 1.80 3 3/16 3 3/8 S1250-27G 1 1/4 1.6255 1.80 3 11/16 3 7/8 S1250-31G 1 1/4 1.6255 1.80 4 3/16 4 3/8 S1250-35G Post Press Fit Outside Press Fit Overall Self- Diameter Diameter Diameter Length Length Lubricating A (in) B (in) C (in) E (in) L (in) Part No. 1/4 1.6255 1.80 4 11/16 4 7/8 S1250-39G 1 1/4 1.6255 1.80 1 1/4 1.6255 1.80 5 11/16 5 7/8 S1250-47G 1 1/2 2.0005 2.18 11/16 7/8 S1500-7G 1 1/2 2.0005 2.18 1 3/16 1 3/8 S1500-11G 1 1/2 2.0005 2.18 1 11/16 1 7/8 S1500-15G 1 1/2 2.0005 2.18 2 3/16 2 3/8 S1500-19G 1/2 2.0005 2.18 2 11/16 2 7/8 S1500-23G 1 1/2 2.0005 2.18 1 1/2 2.0005 2.18 3 3/16 3 3/8 S1500-27G 1 1/2 2.0005 2.18 3 11/16 3 7/8 S1500-31G 1 1/2 2.0005 2.18 4 3/16 4 3/8 S1500-35G 1 1/2 2.0005 2.18 4 11/16 4 7/8 S1500-39G 1 1/2 2.0005 2.18 5 11/16 5 7/8 S1500-47G 2 2.5005 2.68 1 3/16 1 3/8 S2000-11G 2 2.5005 2.68 1 11/16 1 7/8 S2000-15G 2 2.5005 2.68 2 3/16 2 3/8 S2000-19G 2 2.5005 2.68 2 11/16 2 7/8 S2000-23G 2 2.5005 2.68 3 3/16 3 3/8 S2000-27G 2 2.5005 2.68 3 11/16 3 7/8 S2000-31G 2 2.5005 2.68 4 3/16 4 3/8 S2000-35G 2 2.5005 2.68 4 11/16 4 7/8 S2000-39G 2 2.5005 2.68 5 11/16 5 7/8 S2000-47G 2 1/2 3.2505 3.43 1 3/16 1 3/8 S2500-11G 2 1/2 3.2505 3.43 1 11/16 1 7/8 S2500-15G 2 1/2 3.2505 3.43 2 3/16 2 3/8 S2500-19G 2 1/2 3.2505 3.43 2 11/16 2 7/8 S2500-23G 2 1/2 3.2505 3.43 3 3/16 3 3/8 S2500-27G 2 1/2 3.2505 3.43 3 11/16 3 7/8 S2500-31G 2 1/2 3.2505 3.43 4 3/16 4 3/8 S2500-35G 2 1/2 3.2505 3.43 4 11/16 4 7/8 S2500-39G 2 1/2 3.2505 3.43 5 11/16 5 7/8 S2500-47G 3 3.7505 3.99 3 3/16 3 3/8 S3000-27G 3.7505 3.99 3 11/16 3 7/8 S3000-31G 3 3.7505 3.99 3.7505 3.99 4 11/16 4 7/8 S3000-39G 3 3.7505 3.99 5 11/16 5 7/8 S3000-47G 15

Mold Components Self-Lubricating Ejector Bushings ME1000L Product Features Mold component products feature self-lubricating aluminum bronze bushings ideally suited for running with the MP line of Guide Posts. These self-lubricating bushings contain graphite plugs which are impregnated with oil. When the bushings reach 80-90 F as a result of friction between the bushing and guide post, oil is drawn from the plug thus lubricating the wear surface. A dark smear pattern is created on the wear surface as the oil and graphite are imbedded into the bronze or steel grain. This provides the lubrication necessary for continuous performance of the tool. Part Nom. Number I.D. D (in) A (in) B (in) C (in) (in) L (in) ME750 3/4.751 1.1255 1.124 1.302 1 1 1/2 ME875 7/8.876 1.2505 1.249 1.427 1 1 1/2 ME1000 1 1.001 1.3755 1.374 1.552 1 1/8 1 3/4 1 1.001 1.3755 1.374 1.552 ME1000L 1 1.001 1.3755 1.374 1.552 1 5/8 2 ME1250 1 1/4 1.251 1.6255 1.624 1.802 1 1/8 1 3/4 1 1/4 1.251 1.6255 1.624 1.802 ME1250L 1/4 1.251 1.6255 1.624 1.802 1 7/8 2 1/2 ME1500 1 1/2 1.501 2.0005 1.999 2.177 1 1/8 1 3/4 1 1/2 1.501 2.0005 1.999 2.177 ME1500L 1/2 1.501 2.0005 1.999 2.177 1 7/8 2 1/2 ME2000 2 2.001 2.5005 2.499 2.687 1 5/8 2 1/4 16

Ball Bearing Cages Product Features Ball cages are manufactured from a heat treated aluminum alloy which provides tough, wear resistant qualities. The ball bearings are vacuum degassed quality, fatigue resistant steel and are inspected to ensure roundness, smoothness and dimensional conformance. The ball bearings are arranged in the cage in a spiral pattern to minimize tracking or grooving and assure uniform wear. Ball cages are mounted to drilled and tapped guide posts by a special washer assembly which permits the cage to rotate freely around the guide post when not under pre-load. 6-0808-822 TYPE I For Type I Ball Bearing Bushing Assembly TYPE II For Type II and Type III Ball Bearing Bushing Assemblies Posts Length Type I Type II Diameter C S X Part Part O (in) (in) (in) (in) Number Number 1 1 1/2 7/16 3/16 6-0806-821 1 2 11/16 3/16 6-0808-821 1 2 1 1/16 3/16 6-0808-822 2 1/2 1 5/16 3/16 6-0810-822 1 3/16 1 3 1 9/16 3/16 6-0812-822 1 3 1/4 1 13/16 3/16 6-0813-822 1 3 1/2 2 1/16 3/16 6-0814-822 1 3 3/4 2 5/16 3/16 6-0815-822 1 1/4 1 1/2 7/16 3/16 6-1006-821 1 1/4 2 11/16 3/16 6-1008-821 1 1/4 2 3/4 1 7/16 3/16 6-1011-822 1/4 3 1/4 1 11/16 3/16 6-1013-822 1 1/4 3/16 1 1/4 3 3/4 1 15/16 3/16 6-1015-822 1 1/4 4 2 3/16 3/16 6-1016-822 1 1/4 4 1/4 2 7/16 3/16 6-1017-822 1 1/4 4 3/4 2 15/16 3/16 6-1019-822 1 1/2 2 11/16 1/4 6-1208-821 1 1/2 2 1/2 15/16 1/4 6-1210-821 1 1/2 2 3/4 1 7/16 1/4 6-1211-822 1 1/2 3 1/2 1 13/16 1/4 6-1214-822 1 1/2 4 1/4 2 3/16 1/4 6-1217-822 1 1/2 4 1/2 2 7/16 1/4 6-1218-822 1 1/2 5 2 15/16 1/4 6-1220-822 1 1/2 5 1/2 3 7/16 1/4 6-1222-822 1 1/2 6 3 15/16 1/4 6-1224-822 1 3/4 2 1/2 15/16 1/4 6-1410-821 3/4 3 1 3/16 1/4 6-1412-821 1 3/4 1/4 1 3/4 3 1/4 1 11/16 1/4 6-1413-822 1 3/4 4 2 1/16 1/4 6-1416-822 Posts Length Type I Type II Diameter C S X Part Part O (in) (in) (in) (in) Number Number 1 3/4 4 3/4 2 7/16 1/4 6-1419-822 1 3/4 5 1/4 2 15/16 1/4 6-1421-822 1 3/4 5 3/4 3 7/16 1/4 6-1423-822 1 3/4 6 1/4 3 15/16 1/4 6-1425-822 1 3/4 6 3/4 4 7/16 1/4 6-1427-822 2 3 1 3/16 1/4 6-1612-821 2 3 1/2 1 7/16 1/4 6-1614-821 2 3 3/4 1 15/16 1/4 6-1615-822 2 4 1/2 2 5/16 1/4 6-1618-822 5 1/4 2 11/16 1/4 6-1621-822 2 1/4 2 5 5/8 3 1/16 1/4 6-1623-822 2 6 3 7/16 1/4 6-1624-822 2 6 1/2 3 15/16 1/4 6-1626-822 2 7 4 7/16 1/4 6-1628-822 2 7 1/2 4 15/16 1/4 6-1630-822 2 1/2 4 1 11/16 3/8 6-2016-821 2 1/2 5 3/4 3 3/8 6-2023-822 2 1/2 6 1/2 3 3/8 3/8 6-2026-822 2 1/2 7 1/4 3 3/4 3/8 6-2029-822 2 1/2 7 3/4 4 1/4 3/8 6-2031-822 2 1/2 8 1/4 4 3/4 3/8 6-2033-822 2 1/2 8 3/4 5 1/4 3/8 6-2035-822 3 4 1 11/16 3/8 6-2416-821 3 5 3/4 3 3/8 6-2423-822 3 6 1/2 3 3/8 3/8 6-2426-822 3 7 1/4 3 3/4 3/8 6-2429-822 3 7 3/4 4 1/4 3/8 6-2431-822 3 8 1/4 4 3/4 3/8 6-2433-822 3 8 3/4 5 1/4 3/8 6-2435-822 17

Ball Bearing Demountable Guide Posts 5-0813-826 Product Features Precision ball bearing guide posts are manufactured from hardened steel to assure free rolling of balls and high wear resistance. Each post is drilled and tapped at the bottom for mounting of the ball cage washer assembly. This unique mounting method permits the ball cage, except when under pre-load, to freely rotate 360 degrees around the guide post thus eliminating scoring or tracking of the guide post surface. Demountable posts are tap fit and held in place with toe clamps and screws. They can be removed and assembled multiple times without damaging or distorting the mounting holes in the die set thus simplifying die building and maintenance. Demountable posts are also used to replace press fit posts when the press fit hole has been damaged and the straight pin no longer fits securely in the hole. NOTES: All Ball Cage washer assembly sold separately and dependent on Type I, II or III assembly methods. Refer to page 30 for washer assembly part numbers. All demountable guide posts are supplied with mounting clamps and screws. See pages 32 & 33 for clamping dimensions or to order additional toe clamps or mounting screws. 18

Ball Bearing Demountable Guide Posts Diameter Diameter Press Fit Working O B Length Length Part (in) (in) E1 (in) F1 (in) Number 1 1 5/16 1 3/16 2 1/2 5-0810-826 1 1 5/16 1 3/16 2 3/4 5-0811-826 1 1 5/16 1 3/16 3 5-0812-826 1 1 5/16 1 3/16 3 1/4 5-0813-826 1 1 5/16 1 3/16 3 1/2 5-0814-826 1 1 5/16 1 3/16 3 3/4 5-0815-826 1 1 5/16 1 3/16 4 5-0816-826 1 1 5/16 5/16 1 3/16 3/16 4 1/4 5-0817-826 1 1 5/16 1 3/16 4 1/2 5-0818-826 1 1 5/16 1 3/16 4 3/4 5-0819-826 1 1 5/16 1 3/16 5 1/4 5-0821-826 1 1 5/16 1 3/16 5 3/4 5-0823-826 1 1 5/16 1 3/16 6 1/4 5-0825-826 1 1 5/16 1 3/16 6 3/4 5-0827-826 1 1 5/16 1 3/16 7 1/4 5-0829-826 1 1 5/16 1 3/16 7 3/4 5-0831-826 1 1/4 1 9/16 1 3/16 3 1/4 5-1013-826 1 1/4 1 9/16 1 3/16 3 1/2 5-1014-826 1 1/4 1 9/16 1 3/16 3 3/4 5-1015-826 1 1/4 1 9/16 1 3/16 4 5-1016-826 1 1/4 1 9/16 1 3/16 4 1/4 5-1017-826 1 1/4 1 9/16 1 3/16 4 1/2 5-1018-826 1 1/4 1 9/16 1 3/16 4 3/4 5-1019-826 1 1/4 1/4 1 9/16 9/16 1 3/16 3/16 5 1/4 5-1021-826 1 1/4 1 9/16 1 3/16 5 3/4 5-1023-826 1 1/4 1 9/16 1 3/16 6 1/4 5-1025-826 1 1/4 1 9/16 1 3/16 6 3/4 5-1027-826 1 1/4 1 9/16 1 3/16 7 1/4 5-1029-826 1 1/4 1 9/16 1 3/16 7 3/4 5-1031-826 1 1/4 1 9/16 1 3/16 8 3/4 5-1035-826 1 1/4 1 9/16 1 3/16 9 3/4 5-1039-826 1 1/4 1 9/16 1 3/16 10 3/4 5-1043-826 1 1/2 1 7/8 1 7/16 3 1/4 5-1213-826 1 1/2 1 7/8 1 7/16 3 1/2 5-1214-826 1 1/2 1 7/8 1 7/16 3 3/4 5-1215-826 1 1/2 1 7/8 1 7/16 4 5-1216-826 1 1/2 1 7/8 1 7/16 4 1/4 5-1217-826 1 1/2 1 7/8 1 7/16 4 1/2 5-1218-826 1 1/2 1 7/8 1 7/16 5 5-1220-826 1 1/2 1 7/8 1 7/16 5 1/2 5-1222-826 1 1/2 1 7/8 1 7/16 6 5-1224-826 1 1/2 1 7/8 1 7/16 6 1/2 5-1226-826 1 1/2 1 7/8 1 7/16 7 5-1228-826 1 1/2 1 7/8 1 7/16 7 1/2 5-1230-826 1 1/2 1 7/8 1 7/16 8 5-1232-826 1 1/2 1 7/8 1 7/16 8 1/2 5-1234-826 1 1/2 1 7/8 1 7/16 9 5-1236-826 1 1/2 1 7/8 1 7/16 9 1/2 5-1238-826 1 1/2 1 7/8 1 7/16 10 5-1240-826 1 1/2 1 7/8 1 7/16 10 1/2 5-1242-826 1 1/2 1 7/8 1 7/16 11 5-1244-826 1 1/2 1 7/8 1 7/16 11 1/2 5-1246-826 1 1/2 1 7/8 1 7/16 12 1/2 5-1250-826 1 3/4 2 1/4 1 11/16 3 3/4 5-1415-826 1 3/4 2 1/4 1 11/16 4 5-1416-826 1 3/4 3/4 2 1/4 1/4 1 11/16 11/16 4 1/4 5-1417-826 1 3/4 2 1/4 1 11/16 4 1/2 5-1418-826 1 3/4 2 1/4 1 11/16 4 3/4 5-1419-826 1 3/4 2 1/4 1 11/16 5 1/4 5-1421-826 1 3/4 2 1/4 1 11/16 5 3/4 5-1423-826 19 Diameter Diameter Press Fit Working O B Length Length Part (in) (in) E1 (in) F1(in) Number 1 3/4 2 1/4 1 11/16 6 1/4 5-1425-826 1 3/4 2 1/4 1 11/16 6 3/4 5-1427-826 1 3/4 2 1/4 1 11/16 7 1/4 5-1429-826 1 3/4 2 1/4 1 11/16 7 3/4 5-1431-826 1 3/4 2 1/4 1 11/16 8 1/4 5-1433-826 1 3/4 2 1/4 1 11/16 8 3/4 5-1435-826 1 3/4 3/4 2 1/4 1/4 1 11/16 11/16 9 1/4 5-1437-826 1 3/4 2 1/4 1 11/16 9 3/4 5-1439-826 1 3/4 2 1/4 1 11/16 10 1/4 5-1441-826 1 3/4 2 1/4 1 11/16 10 3/4 5-1443-826 1 3/4 2 1/4 1 11/16 11 1/4 5-1445-826 1 3/4 2 1/4 1 11/16 12 1/4 5-1449-826 1 3/4 2 1/4 1 11/16 13 1/4 5-1453-826 1 3/4 2 1/4 1 11/16 14 1/4 5-1457-826 1 3/4 2 1/4 1 11/16 15 1/4 5-1461-826 2 2 1/2 1 15/16 4 1/4 5-1617-826 2 2 1/2 1 15/16 4 1/2 5-1618-826 2 2 1/2 1 15/16 4 3/4 5-1619-826 2 2 1/2 1 15/16 5 5-1620-826 2 2 1/2 1 15/16 5 1/4 5-1621-826 2 2 1/2 1 15/16 5 1/2 5-1622-826 2 2 1/2 1 15/16 5 3/4 5-1623-826 2 2 1/2 1 15/16 6 5-1624-826 2 2 1/2 1 15/16 6 1/2 5-1626-826 2 2 1/2 1 15/16 7 5-1628-826 2 2 1/2 1 15/16 7 1/2 5-1630-826 2 2 1/2 1 15/16 8 5-1632-826 2 2 1/2 1 15/16 8 1/2 5-1634-826 2 2 1/2 1 15/16 9 5-1636-826 2 2 1/2 1 15/16 9 1/2 5-1638-826 2 2 1/2 1 15/16 10 5-1640-826 2 2 1/2 1 15/16 10 1/2 5-1642-826 2 2 1/2 1 15/16 11 5-1644-826 2 2 1/2 1 15/16 12 5-1648-826 2 2 1/2 1 15/16 13 5-1652-826 2 2 1/2 1 15/16 14 5-1656-826 2 2 1/2 1 15/16 15 5-1660-826 2 2 1/2 1 15/16 16 5-1664-826 2 1/2 3 1/32 1 15/16 6 5-2024-826 2 1/2 3 1/32 1 15/16 6 1/2 5-2026-826 2 1/2 3 1/32 1 15/16 7 5-2028-826 2 1/2 3 1/32 1 15/16 8 5-2032-826 2 1/2 3 1/32 1 15/16 9 5-2036-826 1/2 1/32 15/16 10 5-2040-826 2 1/2 3 1/32 1 15/16 1/2 1/32 15/16 11 5-2044-826 2 1/2 3 1/32 1 15/16 12 5-2048-826 13 5-2052-826 14 5-2056-826 2 1/2 3 1/32 1 15/16 15 5-2060-826 2 1/2 3 1/32 1 15/16 18 5-2072-826 3 3 1/2 2 7/16 6 5-2424-826 3 3 1/2 2 7/16 6 1/2 5-2426-826 3 3 1/2 2 7/16 7 1/2 5-2430-826 3 3 1/2 2 7/16 8 1/2 5-2434-826 3 3 1/2 2 7/16 9 1/2 5-2438-826 1/2 7/16 10 1/2 5-2442-826 3 3 1/2 2 7/16 1/2 7/16 11 1/2 5-2446-826 12 1/2 5-2450-826 13 1/2 5-2454-826 3 3 1/2 2 7/16 14 1/2 5-2458-826 3 3 1/2 2 7/16 17 1/2 5-2470-826

Ball Bearing Press Fit Guide Posts Product Features Precision ball bearing guide posts are manufactured from hardened steel to assure free rolling of balls and high wear resistance. Each post is drilled and tapped at the bottom for mounting of the ball cage washer assembly. This unique mounting method permits the ball cage, except when under pre-load, to freely rotate 360 degrees around the guide post thus eliminating scoring or tracking of the guide post surface. 5-0820-82 NOTES: Ball Cage washer assembly sold separately and dependent on Type I, II or III assembly methods. Refer to page 30 for washer assembly part numbers. Diameter Length Part O (in) L (in) Number 1 3 1/4 5-0813-82 1 3 3/4 5-0815-82 1 4 1/4 5-0817-82 1 4 1/2 5-0818-82 1 4 3/4 5-0819-82 1 5 5-0820-82 1 5 1/4 5-0821-82 1 5 1/2 5-0822-82 1 5 3/4 5-0823-82 1 6 5-0824-82 1 6 1/2 5-0826-82 1 7 5-0828-82 1 7 1/2 5-0830-82 1 8 5-0832-82 1 8 1/2 5-0834-82 1 9 5-0836-82 1 1/4 4 1/4 5-1017-82 1 1/4 4 3/4 5-1019-82 1 1/4 5 1/4 5-1021-82 1 1/4 5 1/2 5-1022-82 1 1/4 5 3/4 5-1023-82 1 1/4 6 5-1024-82 1 1/4 6 1/2 5-1026-82 1 1/4 1/4 7 5-1028-82 1 1/4 7 1/2 5-1030-82 1 1/4 8 5-1032-82 1 1/4 8 1/2 5-1034-82 1 1/4 9 5-1036-82 1 1/4 10 5-1040-82 1 1/4 11 5-1044-82 1 1/4 12 5-1048-82 1 1/2 4 1/4 5-1217-82 1 1/2 5 5-1220-82 1/2 5 3/4 5-1223-82 1 1/2 1/2 6 5-1224-82 1 1/2 6 1/2 5-1226-82 1 1/2 7 5-1228-82 Diameter Length Part O (in) L (in) Number 1 1/2 7 1/2 5-1230-82 1 1/2 8 5-1232-82 1 1/2 8 1/2 5-1234-82 1 1/2 9 5-1236-82 1 1/2 9 1/2 5-1238-82 1 1/2 10 5-1240-82 1 1/2 10 1/2 5-1242-82 1 1/2 11 5-1244-82 1 1/2 11 1/2 5-1246-82 1 1/2 12 5-1248-82 1 1/2 12 1/2 5-1250-82 1 1/2 13 5-1252-82 1 1/2 14 5-1256-82 1 3/4 5 5-1420-82 1 3/4 5 3/4 5-1423-82 1 3/4 6 1/2 5-1426-82 1 3/4 7 5-1428-82 1 3/4 7 1/2 5-1430-82 1 3/4 8 5-1432-82 1 3/4 8 1/2 5-1434-82 1 3/4 9 5-1436-82 3/4 9 1/2 5-1438-82 1 3/4 3/4 10 5-1440-82 1 3/4 10 1/2 5-1442-82 1 3/4 11 5-1444-82 1 3/4 11 1/2 5-1446-82 1 3/4 12 5-1448-82 1 3/4 12 1/2 5-1450-82 1 3/4 13 5-1452-82 1 3/4 14 5-1456-82 1 3/4 15 5-1460-82 1 3/4 17 5-1468-82 2 5 3/4 5-1623-82 2 6 1/2 5-1626-82 2 7 1/4 5-1629-82 2 7 1/2 5-1630-82 2 7 3/4 5-1631-82 Diameter Length Part O (in) L (in) Number 2 8 5-1632-82 2 8 1/2 5-1634-82 2 9 5-1636-82 2 9 1/2 5-1638-82 2 10 5-1640-82 2 10 1/2 5-1642-82 2 11 5-1644-82 2 11 1/2 5-1646-82 2 12 5-1648-82 2 12 1/2 5-1650-82 2 13 5-1652-82 2 14 5-1656-82 2 15 5-1660-82 2 16 5-1664-82 2 17 5-1668-82 2 18 5-1672-82 2 1/2 8 5-2032-82 2 1/2 8 3/4 5-2035-82 2 1/2 9 1/2 5-2038-82 2 1/2 10 5-2040-82 2 1/2 11 5-2044-82 2 1/2 12 5-2048-82 2 1/2 13 5-2052-82 2 1/2 14 5-2056-82 2 1/2 17 5-2068-82 2 1/2 18 5-2072-82 2 1/2 20 5-2080-82 3 8 1/2 5-2434-82 3 9 1/4 5-2437-82 3 10 5-2440-82 3 11 5-2444-82 3 12 5-2448-82 3 13 5-2452-82 3 14 5-2456-82 3 17 5-2468-82 3 20 5-2480-82 20

Ball Bearing Demountable Bushings Product Features These demountable bushings are tap fit into location and seat flush with the ground face of the punch holder. The bushings are held in place with toe clamps and screws which provide perfect alignment of the bushing with the bore perpendicular to the ground surface of the punch holder. The clamp and screws provide four times the holding power compared to pressed-in bushings, yet they can be easily removed and assembled thus simplifying die building and maintenance. 6-0807-85 Post Overall Diameter Bushing Diameters Length E Length F Length Part (in) A (in) B (in) C (in) C1 (in) (in) (in) (in) Number 1 1 3/8 1 7/8 2 1/8 2.283 1 3/16 1 1/4 2 7/16 6-0805-85 3/8 7/8 2 1/8 2.283 3/16 1 3/4 2 15/16 6-0807-85 1 1 3/8 1 7/8 2.000 2.283 1 3/16 1 1 3/8 1 7/8 2 1/8 2.283 1 3/16 2 1/4 3 7/16 6-0809-85 1 1 3/8 1 7/8 2 1/8 2.283 1 3/16 2 3/4 3 15/16 6-0811-85 1 1/4 1 5/8 2 1/8 2 3/8 2.533 1 3/16 1 3/4 2 15/16 6-1007-85 1 1/4 1 5/8 2 1/8 2.500 3/8 2.533 1 3/16 2 1/4 3 7/16 6-1009-85 1 1/4 1 5/8 2 1/8 2 3/8 2.533 1 3/16 2 3/4 3 15/16 6-1011-85 1 1/2 1 7/8 2 1/2 2 7/8 3.033 1 7/16 1 1/2 2 15/16 6-1206-85 1/2 7/8 1/2 2 7/8 3.033 7/16 2 1/4 3 11/16 6-1209-85 1 1/2 1 7/8 2 1/2 2.875 3.033 1 7/16 1/2 7/8 1/2 2 7/8 3.033 7/16 3 4 7/16 6-1212-85 1 1/2 1 7/8 2 1/2 2 7/8 3.033 1 7/16 3 1/2 4 15/16 6-1214-85 1 3/4 2 1/8 2 3/4 3 1/8 3.283 1 11/16 1 3/4 3 7/16 6-1407-85 1 3/4 2 1/8 2 3/4 32.875 1/8 3.283 1 11/16 2 1/2 4 3/16 6-1410-85 1 3/4 2 1/8 2 3/4 3 1/8 3.283 1 11/16 3 1/4 4 15/16 6-1413-85 2 2 1/2 3 1/4 3 5/8 3.783 1 15/16 2 3 15/16 6-1608-85 2 2 1/2 3 1/4 3 5/8 3.783 1 15/16 2 3/4 4 11/16 6-1611-85 2 2 1/2 3 1/4 3.375 5/8 3.783 1 15/16 3 1/2 5 7/16 6-1614-85 2 2 1/2 3 1/4 3 5/8 3.783 1 15/16 4 1/4 6 3/16 6-1617-85 2 2 1/2 3 1/4 3 5/8 3.783 1 15/16 5 6 15/16 6-1620-85 2 1/2 3 3 3/4 4 1/8 4.283 1 15/16 2 3 15/16 6-2008-85 3 4 15/16 6-2012-85 2 1/2 3 3 3/4 4.010 4.283 1 15/16 4 5 15/16 6-2016-85 2 1/2 3 3 3/4 4 1/8 4.283 1 15/16 4 3/4 6 11/16 6-2019-85 2 1/2 3 3 3/4 4 1/8 4.283 1 15/16 5 1/2 7 7/16 6-2022-85 3 1/2 4 1/4 4 3/4 4.908 1 15/16 2 3 15/16 6-2408-85 3 4 15/16 6-2412-85 3 3 1/2 4 1/4 4.500 4.908 1 15/16 4 5 15/16 6-2416-85 3 3 1/2 4 1/4 4 3/4 4.908 1 15/16 4 3/4 6 11/16 6-2419-85 3 3 1/2 4 1/4 4 3/4 4.908 1 15/16 5 1/2 7 7/16 6-2422-85 21

Ball Bearing Straight Sleeve Bushings Product Features Straight sleeve bushings are manufactured from high quality hardened steel and the bushings are finish ground for a press fit. Like all ball bearing components, these straight sleeve bushings are completely interchangeable. INSTALLATION INSTRUCTIONS 6-0814-86 In order to avoid the bushing close-in which occurs as a result of pressfit, these bushings should be retained with Danly Bushing Mount. When so installed, it is not necessary to hone the bushing bore after installation, and the bushing fit will be correct. APPLICATION OF DANLY BUSHING MOUNT 1. Degrease bushing OD and die shoe bore with alcohol, acetone or other volatile solvent and wipe dry. 2. Apply Bushing Mount sparingly and wring bushing into die shoe. 3. Allow a 4-hour cure at 72 F. Do not disturb bushing until cure is complete. DANLY BUSHING MOUNT: Part number 9-60-82 Post Diameter Bushing Diameters Length Part (in) A (in) B (in) L2 (in) Number 1 1 3/8 1 7/8 2 1/2 6-0810-86 1 1 3/8 1 7/8 3 6-0812-86 3/8 7/8 3 1/2 6-0814-86 1 1 3/8 1 7/8 1 1 3/8 1 7/8 4 6-0816-86 1 1 3/8 1 7/8 4 1/2 6-0818-86 1 1 3/8 1 7/8 5 6-0820-86 1 1/4 1 5/8 2 1/8 3 6-1012-86 1 1/4 1 5/8 2 1/8 3 1/2 6-1014-86 1 1/4 1 5/8 2 1/8 4 6-1016-86 1 1/4 1 5/8 2 1/8 1/4 5/8 1/8 4 1/2 6-1018-86 1 1/4 1 5/8 2 1/8 5 6-1020-86 1 1/4 1 5/8 2 1/8 6 6-1024-86 1 1/2 1 7/8 2 1/2 3 6-1212-86 1 1/2 1 7/8 2 1/2 3 3/4 6-1215-86 1 1/2 1 7/8 2 1/2 4 1/2 6-1218-86 1/2 7/8 1/2 5 6-1220-86 1 1/2 1 7/8 2 1/2 1 1/2 1 7/8 2 1/2 5 1/2 6-1222-86 1 1/2 1 7/8 2 1/2 6 6-1224-86 1 1/2 1 7/8 2 1/2 7 6-1228-86 1 1/2 1 7/8 2 1/2 8 6-1232-86 1 3/4 2 1/8 2 3/4 3 1/2 6-1414-86 1 3/4 2 1/8 2 3/4 4 1/4 6-1417-86 1 3/4 2 1/8 2 3/4 3/4 1/8 3/4 5 6-1420-86 1 3/4 2 1/8 2 3/4 5 1/2 6-1422-86 Post Diameter Bushing Diameters Length Part (in) A (in) B (in) L2 (in) Number 1 3/4 2 1/8 2 3/4 6 6-1424-86 3/4 1/8 3/4 7 6-1428-86 1 3/4 2 1/8 2 3/4 1 3/4 2 1/8 2 3/4 8 6-1432-86 1 3/4 2 1/8 2 3/4 9 6-1436-86 2 2 1/2 3 1/4 4 6-1616-86 2 2 1/2 3 1/4 4 3/4 6-1619-86 2 2 1/2 3 1/4 5 1/2 6-1622-86 1/2 1/4 6 1/4 6-1625-86 2 2 1/2 3 1/4 2 2 1/2 3 1/4 7 6-1628-86 2 2 1/2 3 1/4 8 6-1632-86 2 2 1/2 3 1/4 9 6-1636-86 2 2 1/2 3 1/4 10 6-1640-86 2 1/2 3 3 3/4 6 6-2024-86 2 1/2 3 3 3/4 6 3/4 6-2027-86 2 1/2 3 3 3/4 7 1/2 6-2030-86 2 1/2 3 3 3/4 1/2 3/4 8 1/2 6-2034-86 2 1/2 3 3 3/4 9 1/2 6-2038-86 2 1/2 3 3 3/4 10 1/2 6-2042-86 3 3 1/2 4 1/4 6 6-2424-86 3 3 1/2 4 1/4 6 3/4 6-2427-86 1/2 1/4 7 1/2 6-2430-86 3 3 1/2 4 1/4 1/2 1/4 8 1/2 6-2434-86 3 3 1/2 4 1/4 9 1/2 6-2438-86 3 3 1/2 4 1/4 10 1/2 6-2442-86 22

This illustration shows how the D (bolt circle) dimension is obtained. 6-16-11& 6-16-111 Demountable Bosses Product Features Demountable bosses are ideal for heavy duty applications and are available for guide posts from 2" in diameter and larger. The bosses are available in three styles. Type 1 is a combination bushing and guide post support. Type 2 is a boss bushing which is flange mounted with the major bearing surface contained within the die set. Type 3 is also classified as a boss-bushing type but with the guide post bearing surface extended below the mounting flange. TYPE 1 Demountable Boss Part Number A K Post Bushing B C D E F L (in) (in) Support Boss (in) (in) (in) (in) (in) (in) (in)2 1 1/2 6-16-11 6-16-111 2.5005 5 4 19/32 21/32 5/16 1 13/16 2 3 1/2 6-16-12 6-16-121 2.5005 5 4 19/32 21/32 5/16 3 13/16 5 1/2 6-16-13 6-16-131 5 13/16 2 1/2 1 1/2 6-20-11 6-20-111 3.2505 6 6 21/32 5/16 1 13/16 2 1/2 3 1/2 6-20-12 6-20-121 3.2505 6 6 21/32 5/16 3 13/16 5 1/2 6-20-13 6-20-131 5 13/16 3 3 1/2 6-24-12 6-24-121 3.7505 7 7 1/16 25/32 5/16 3 13/16 3 3.7505 7 7 1/16 25/32 5/16 5 1/2 6-24-13 6-24-131 5 13/16 TYPE 2 Boss Bushings A K Part Number B C D E F L (in) (in) (in) (in) (in) (in) (in) (in) 2 1 1/2 6-16-18 2.6880 4 3 1/2 17/32 2 1/2 4 2 1/2 1 1/2 6-20-18 3.4380 5 4 5/8 21/32 3 4 1/2 TYPE 3 Boss Bushings 6-16-19 A K Part Number B C D E F L (in) (in) (in) (in) (in) (in) (in) (in) 2 2 1/2 6-16-19 2.6880 4 3 1/2 17/32 1 1/2 4 2 1/2 2 1/2 6-20-19 3.4380 5 4 5/8 21/32 2 4 1/2 23

Ball Bearing Components Selection Guide Product Features For proper post, bushing and cage selection, the operating conditions of the die must be taken into consideration. Factors such as press speed, shut height, stroke length and operating environment all play a role in selecting the appropriate operating condition to give the best performance possible of your components. The operating conditions include full pre-load, pre-load relieved and total disengagement. Type I Full Pre-Load Throughout Stroke Type I component assemblies ensure that all ball bearings remain in constant contact with the guide post and bushing throughout the entire press stroke. This assembly is recommended for higher speed, short stroke dies. Type II Pre-Load Relived or Partially Relieved Type II component assemblies are designed so the ball cage never leaves the bushing; however the guide post disengages the bushing at the beginning of each stroke. This assembly is often preferred as pinch points are eliminated and foreign matter cannot get inside the assembly and damage the components. This assembly is often utilized in medium and long stroke dies. Type III Total Disengagement of Cage from Bushing Type III component assemblies are designed so the ball cage totally disengages from the bushing. This assembly is utilized on long stroke applications. 24

Type I Component Selection Guide Post Diam. Z E U1 U2 (in) (in) (in) (in) (in) 1 5/16 1 3/16 1/16 1/8 1 1/4 5/16 1 3/16 1 1/2 3/8 1 7/16 1 3/4 3/8 1 11/16 1/16 1/8 2 3/8 1 15/16 2 1/2 1/2 1 15/16 3 1/2 1 15/16 PRESS FIT POSTS 1. Calculate L, the desired guide post length, using one of the following 2 formulas: Assembly with Straight Sleeve Bushings: L=T-U 2 -Z Assembly with Demountable Bushings: L=T-U 1 -Z-J+E 2. Select a post length from the catalog that is equal to L calculated above. If the calculated L value is not a standard catalog length, you have two options. Choose the next longest length and cut off to the calculated L dimension or select a shorter length and recess the post in the punch holder to obtain correct L dimension. Note: Press fit length should be equal to or greater than the diameter of the guide post. DEMOUNTABLE POSTS 1. Calculate F 1, the desired guide post length, using one of the following 2 formulas: Assembly with Straight Sleeve Bushings: F 1 =T-U 2 -Z-K (Note F+J+K+Y<T) Assembly with Demountable Bushing: F 1 =T-U 1 -Z-J+E-K (Note L 2 +K+Y<T) 2. Select a post length from the catalog that is equal to F 1 calculated above. If the calculated F 1 value is not a standard catalog length, choose a catalog length that is close to but less than the calculated F 1. Note: Demountable posts cannot be cut off. BUSHING & CAGE SELECTION Selection of a Type 1 ball bearing bushing and cage assembly is based on the required stroke and the guide post diameter. 1. Determine the guide post diameter required and the stroke required. 2. Using the selection chart on page 26, find the desired stroke. Move down this column to the colored square on the horizontal line opposite the required post diameter. 3. Select the required bushing length which is listed to the left of the selected square in the columns labeled Demountable Shoulder and Straight Sleeve. Note: For applications with no off-center loading, select the bushing with the shortest overall length from the selection chart. However for longer stroke applications or where side-loading may be present select the bushing with the longest possible length to provide optimal guidance. 4. Select the required cage length which is also listed to the left of the selected square in the column labeled Ball Cage. Note: Shut height permitting, select the longest cage length possible for optimal performance. NOTES: If die grind is not required, stroke may be increased by the amount of die grind allowance, dimension X, found in the right most column of the selection chart. NOTES: A die set designed for a particular stroke may be used in any press of lesser stroke but never in any press where the stroke is greater than originally chosen. 25

Type I Component Selection Guide 26

Type II & III Component Selection Guide PRESS FIT POSTS 1. Calculate L, the desired guide post length, using one of the following 2 formulas: Assembly with Straight Sleeve Bushings: L=T-U 2 -Z Assembly with Demountable Bushings: L=T-U 1 -Z-J+E 2. Select a post length from the catalog that is equal to L calculated above. If the calculated L value is not a standard catalog length, you have two options. Choose the next longest length and cut off to the calculated L dimension or select a shorter length and recess the post in the punch holder to obtain correct L dimension. Note: Press fit length should be equal to or greater than the diameter of the guide post. DEMOUNTABLE POSTS 1. Calculate F 1, the desired guide post length, using one of the following 2 formulas: Assembly with Straight Sleeve Bushings: F 1 =T-U 2 -Z-K (Note F+J+K+Y<T) Assembly with Demountable Bushings: F 1 =T-U 1 -Z-J+E-K (Note L 2 +K+Y<T) 2. Select a post length from the catalog that is equal to F 1 calculated above. If the calculated F 1 value is not a standard catalog length, choose a catalog length that is close to but less than the calculated F 1. Note: Demountable posts cannot be cut off. BUSHING & CAGE SELECTION Selection of a Type II and Type III ball bearing bushing and cage assembly is based on the required stroke and the guide post diameter. 1. Determine the guide post diameter required and the stroke required. 2. Determine the desired operating condition or the extent to which the cage leaves the bushing. 3. Determine if a demountable or straight sleeve bushing is to be used. 4. Using the selection chart on pages 28 & 29, find the desired stroke (S). Move down this column to the colored square on the horizontal line opposite the required post diameter. Find the colored square in the desired operating condition. 5. Select the required bushing length which is listed to the left of the selected square in the columns labeled DemountableShoulder or Straight Sleeve. Note: For applications with no off-center loading, select the bushing with the shortest overall length from the selection chart. However for longer stroke applications or where side-loading may be present select the bushing with the longest possible length to provide optimal guidance. 6. Select the required cage length which is also listed to the left of the selected square in the column labeled Ball Cage. Note: Shut height permitting, select the longest cage length possible for optimal performance. 27 Post Diam. Z E U1 U2 Y O (in) (in) (in) (in) (in) (in) 1 15/32 1 3/16 39/64 1 1/4 15/32 1 3/16 1 1/2 1/2 1 7/16 1 3/4 1/2 1 11/16 1/16 1/16 1/8 3/4 2 1/2 1 15/16 2 1/2 9/16 1 15/16 3 9/16 1 15/16 NOTES: A die set designed for a particular stroke may be used in any press of lesser stroke but never in any press where the stroke is greater than originally chosen.

CAUTION Be sure bushing does not strike punch holder at minimum shut height. If this condition exists, use shorter bushing and corresponding ball cage. COLOR CODE FOR SELECTION GUIDE Type II and III components provide Type I operating conditions Type II & III Bushing & Ball Cage Selection Guide Nom. Ball Bushing Ball Post Diam. Demountable Shoulder Straight Sleeve Cage O E F U1 L2 U2 C 1 1 3/16 1 1/4 2 7/16 1/16 2 1/2 1/8 2 1 3/4 2 15/16 3 2 1/2 2 1/4 3 7/16 3 1/2 3 1 1 3/16 2 3/4 3 15/16 1/16 4 1/8 3 1/4 4 1/2 3 1/2 5 3 3/4 1 1/4 1 3/16 1 3/4 2 15/16 1/16 3 1/8 2 3/4 2 1/4 3 7/16 3 1/2 3 1/4 1 1/4 1 3/16 2 3/4 3 15/16 4 1/16 1/8 3 3/4 4 1/2 4 5 4 1/4 6 4 3/4 1 1/2 1 7/16 1 1/2 2 15/16 1/16 3 1/8 2 3/4 2 1/4 3 11/16 3 3/4 3 1/2 Partial Pre-load 1 1/2 1 7/16 3 4 7/16 4 1/2 4 1/4 3 1/2 4 15/16 1/16 5 1/8 4 1/2 6 5 7 5 1/2 8 6 Pre-load Relieved 1 3/4 1 11/16 1 3/4 3 7/16 1/16 3 1/2 1/8 3 1/4 2 1/2 4 3/16 4 1/4 4 3 1/4 4 15/16 5 4 3/4 1 3/4 1 11/16 1/16 6 1/8 5 1/4 7 5 3/4 8 6 1/4 9 6 3/4 2 1 15/16 2 3 15/16 1/16 4 1/8 3 3/4 2 3/4 4 11/16 4 3/4 4 1/2 3 1/2 5 7/16 5 1/2 5 1/4 Unlimited stroke cage leaves bushing 2 1 15/16 4 1/4 6 3/16 6 1/4 5 5/8 1/16 1/8 5 6 15/16 7 6 8 6 1/2 9 7 10 7 1/2 NOTES: Sleeve Bushing: L 2 + K must be less than T Shoulder Bushing: J + F + K must be less than T 2 1/2 1 15/16 4 5 15/16 1/16 6 1/8 5 3/4 4 3/4 6 11/16 6 3/4 6 1/2 2 1/2 1 15/16 5 1/2 7 7/16 7 1/2 1/16 1/8 7 1/4 8 1/2 7 3/4 9 1/2 8 1/4 10 1/2 8 3/4 Demountable Bushing: Maximum F = T - J - K Sleeve Bushing: Maximum L 2 = T - K 3 1 15/16 28 3 1 15/16 4 5 15/16 1/16 6 1/8 5 3/4 4 3/4 6 11/16 6 3/4 6 1/2 5 1/2 7 7/16 7 1/2 7 1/4 1/16 1/8 8 1/2 7 3/4 9 1/2 8 1/4 10 1/2 8 3/4

Ball Cage C Type II & III Bushing & Ball Cage Selection Guide 1/2 1 1 1/2 2 2 1/2 STROKE S AT MINIMUM SHUT HEIGHT (DIE LIFE DEPLETED) 3 3 1/2 4 4 1/2 5 5 1/2 6 6 1/2 7 7 1/2 8 9 10 11 12 13 14 15 16 V 2 7/8 2 1/2 1 1/8 3 3 3 1/4 3 1/2 3 3/4 3 1/4 1 3/8 3 1/2 3 3/4 2 3/4 1 1/4 3 1/4 1 1/2 3 3/4 3 3/4 4 4 1/4 4 3/4 4 1 3/4 4 1/4 4 3/4 2 3/4 1 1/4 3 2/3 1 5/8 4 1/4 4 1/4 4 1/2 4 1/2 5 52 5 1/2 5 1/2 6 6 3 1/4 1 1/2 4 1 7/8 4 3/4 4 3/4 5 1/4 5 1/4 5 3/4 52 3/4 1/4 6 1/4 6 1/4 6 3/4 6 3/4 3 3/4 1 3/4 4 1/2 1 1/8 5 1/4 5 1/4 5 5/8 5 5/8 6 6 1/2 7 7 1/2 6 2 1/2 6 1/2 7 7 1/2 5 3/4 2 11/16 6 1/2 3 1/16 7 1/4 7 1/4 7 3/4 8 1/4 8 3/4 7 3/4 3 7/16 8 1/4 8 3/4 5 3/4 6 1/2 7 1/4 7 3/4 8 1/4 8 3/4 29 2 11/16 3 1/16 7 1/4 7 3/4 3 7/16 8 1/4 8 3/4

Ball Bearing Components Technical Information BORING SPECIFICATIONS FOR BALL BEARING GUIDE POSTS AND BUSHINGS Post Bore Sizes (in) Diameter Punch Holder for Posts Die Shoe for Bushings A (in) Minimum Maximum Minimum Maximum 1 0.9980 0.9988 1.8748 1.8755 1 1/4 1.2480 1.2488 2.1248 2.1255 1 1/2 1.4975 1.4983 2.4998 2.5005 1 3/4 1.7475 1.7483 2.7498 2.7505 2 1.9975 1.9983 3.2498 3.2505 2 1/2 2.4970 2.4978 3.7498 3.7505 3 2.9970 2.9978 4.2498 4.2505 BALL CAGE WASHER ASSEMBLY Snap Ring- Nominal Washer Assembly Bushing Hex Head Ball Bearing Post Part Number Stop Washer-Retainer Stop Washer Screw Cages Diameter Type I Type II Type Type Type Type Type A (in) Assembly Assembly I II and III II and III I, II and III II and III 1 6-0008-82-1 6-0008-82-2 5-0800-831 5-0800-832 5-0800-840 9-0506-730 6-0800-832 5-0800-840 9-0506-730 1 1/4 6-0010-82-1 6-0010-82-2 5-1000-831 5-1000-832 5/16-18 x 3/4 6-1000-832 1 1/2 6-0012-82-1 6-0012-82-2 5-1200-831 5-1200-832 5-1200-840 9-0607-730 6-1200-832 1 3/4 6-0014-82-1 6-0014-82-2 5-1400-831 5-1400-832 5-1200-840 9-0607-730 3/8-16 x 7/8 6-1400-832 2 6-0016-82-1 6-0016-82-2 5-1600-831 5-1600-832 6-1600-832 2 1/2 6-0020-82-1 6-0020-82-2 5-2000-831 5-2000-832 5-2400-840 6-2000-832 5-2400-840 9-0808-730 1/2-13 x 1 3 6-0024-82-1 6-0024-82-2 5-2400-831 5-2400-832 6-2400-832 NOTES: TYPE I Assembly includes stopwasher retainer and head hex screw. TYPE II Assembly includes stopwasher retainer, bushing stopwasher, hex head screw and snap ring. BUSHING MOUNT Part Number Volume 9-60-82 4 oz. NOTES: A bushing mount is used when installing straight sleeve ball bearing bushings to avoid bushing close-in as a result of press-fit. BALL CAGE WASHER ASSEMBLY Guide Post Tap Sizes Required Seating Torque Diameter O (in) Tap Size Lbs per Inch Lbs per Foot 1 1 1/4 5/16 18 N.C. 320 26 1 1/2 2 3/8 10 N.C. 560 47 2 1/2 3 1/2 13 N.C. 1350 112 Ball Bearing Bushing Lubrication Recommendation During operation of Ball Bearing Bushing Assembly, add lubricant once each 8-hour shift by spray or brush application. Use a refined mineral oil of viscosity 290/340 SSU @ 100 F (39 C) containing EP additives and rust inhibitors. 30

Plain Bearing Components Technical Information BORING SPECIFICATIONS FOR PLAIN BEARING GUIDE POSTS AND BUSHINGS Post Bore Sizes (in) Diameter Die Shoe for Posts Punch Holder for Bushings A (in) Minimum Maximum Minimum Maximum 1/2 0.5001 0.5002 0.8123 0.8130 5/8 0.6252 0.6260 0.9998 1.0005 3/4 0.7502 0.7510 1.1248 1.1255 7/8 0.8752 0.8760 1.3748 1.3755 1 1.0002 1.0010 1.4980 1.5005 1 1/4 1.2502 1.2510 1.7498 1.7505 1 1/2 1.5002 1.5010 1.9998 2.0005 1 3/4 1.7502 1.7510 2.2498 2.2505 2 2.0002 2.0010 2.4998 2.5005 2 1/2 2.5002 2.5010 3.2498 3.2505 3 3.0002 3.0010 3.7498 3.7505 LUBRICANT INFORMATION Part Number Volume 9-01-52 1 Quart 9-02-52 1 Gallon NOTES: For improved component life, lubricant should be applied to bushings during operation. Lubricant is sold by the quart or gallon. ID TOLERANCE FOR PRE-FITTED DEMOUNTABLE BUSHINGS Diameter ID Tolerance A (in) (in) Minimum Maximum 3/4 + 0.0003 + 0.0006 7/8 + 0.0003 + 0.0006 1 + 0.0002 + 0.0007 1 1/4 + 0.0003 + 0.0008 1 1/2 + 0.0004 + 0.0009 1 3/4 + 0.0005 + 0.0010 2 + 0.0005 + 0.0013 2 1/2 + 0.0006 + 0.0014 3 + 0.0008 + 0.0016 31

Clamp Dimensions for Demountable Posts & Bushings FIGURE A FIGURE B FIGURE C FIGURE D NOTES: S FOR 3-CLAMP FOR 4-CLAMP ARRANGEMENT ARRANGEMENT Figure B clamp schematic is for part number 6-98-1 only and supplied on low profile demountable bushings 1-1/2" diameter and larger. All other assemblies are supplied with Figure A style clamps. Posts and bushings are automatically supplied with the appropriate number of mounting clamps and screws. A (L-R Feed) B (F-B Feed) C (Round Dies) (Center Post Sets) CLAMP DIMENSIONS FOR GUIDE POSTS - Plain Bearing & Ball Bearing Clamps & Screw Socket Head screws Post Clamp Part Cap Screw req'd Radius Radius Diam. Part Number Description per C D T M N P A (in) Number S Bushing (in) (in) (in) (in) 7/8 6-90-1 9-0806-41 1/4-20x3/4 long 3 0.193 11/32 39/64 3/4 1 1/16 27/32 1 6-90-1 9-0806-41 1/4-20x3/4 long 3 0.193 11/32 39/64 13/16 1 1/8 7/8 1 1/4 6-93-1 9-1007-41 5/16-18x7/8 long 3 0.250 0.443 3/4 63/64 1 25/64 1 1 1/2 6-93-1 9-1007-41 5/16-18x7/8 long 3 0.250 0.443 3/4 1 1/8 1 17/32 1 1/16 1 3/4 6-93-1 9-1007-41 5/16-18x7/8 long 4 0.250 0.443 3/4 1 19/64 1 45/64 1 3/8 2 6-93-1 9-1007-41 5/16-18x7/8 long 4 0.250 0.443 3/4 1 27/64 1 53/64 1 9/16 2 1/2 6-93-1 9-1007-41 5/16-18x7/8 long 4 0.250 0.443 3/4 1 43/64 2 5/64 1 23/32 3 6-93-1 9-1007-41 5/16-18x7/8 long 4 0.250 0.443 3/4 1 59/64 2 21/64 1 29/32 32