HARTZELL PROPELLER INC. One Propeller Place Piqua, Ohio 45356-2634 U.S.A. Telephone: 937.778.4200 Fax: 937.778.4215 MANUAL REVISION TRANSMITTAL Manual (61-00-65) Illustrated Tool and Equipment Manual REVISION 21 dated October 2017 Attached is a copy of Revision 21 to Hartzell Manual. Page Control Chart for Revision 21 Remove Chapter/Page No. COVER cover and inside cover Insert Chapter/Page No. COVER cover and inside cover REVISION HIGHLIGHTS REVISION HIGHLIGHTS pages 1 thru 4 pages 1 thru 4 LIST OF EFFECTIVE PAGES LIST OF EFFECTIVE PAGES pages 1 thru 4 pages 1 thru 4 TOOL AND EQUIPMENT INDEX TOOL AND EQUIPMENT INDEX pages 2-5 and 2-6 pages 2-5 and 2-6 pages 2-19 and 2-20 pages 2-19 and 2-20 TOOL AND EQUIPMENT LIST TOOL AND EQUIPMENT LIST pages 4-25 and 4-26 pages 4-25 and 4-26 pages 4-42.1 and 4-42.2 pages 4-42.1 and 4-42.2 pages 4-99 and 4-100 pages 4-99 and 4-100 pages 4-157 and 4-158 pages 4-157 and 4-158 NOTE 1: NOTE 2: NOTE 3: Record the removal of a Temporary Revision on the Record of Temporary Revisions page in this manual. When the manual revision has been inserted in the manual, record the information required on the Record of Revisions page in this manual. Pages distributed in this revision may include pages from previous revisions if they are on the opposite side of revised pages. This is done as a convenience to those users who wish to print a two-sided copy of the new revision. This page may be discarded after proper filing of the revision.
(This page is intentionally blank.) Page 2 of 2
Manual No. Revision 21 61-00-65 October 2017 Illustrated Tool and Equipment Manual Hartzell Propeller Inc. One Propeller Place Piqua, Ohio 45356-2634 U.S.A. Phone: 937.778.4200 Fax: 937.778.4215
(This page is intentionally blank.) 1995, 1996, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2011, 2012, 2013, 2014, 2016, 2017 - Hartzell Propeller Inc. - All rights reserved COVER 61-00-65 Inside Cover
COVER Revised to match the manual revision REVISION HIGHLIGHTS Revised to match the manual revision LIST OF EFFECTIVE PAGES Revised to match the manual revision TOOL AND EQUIPMENT INDEX Revised to match the manual revision REVISION 21 HIGHLIGHTS TOOL AND EQUIPMENT LIST Revised the section, "Piston Nut Wrench" Revised the section, "Template" Revised the section, "Propeller Assembly Table" Revised the section, "C-shank Rolling Conversion Kit" Made other minor language/format changes REVISION HIGHLIGHTS 61-00-65 Page 1
(This page is intentionally blank.) REVISION HIGHLIGHTS 61-00-65 Page 2
1. Introduction A. General REVISION 21 HIGHLIGHTS (1) This is a list of current revisions that have been issued against this manual. Please compare to the RECORD OF REVISIONS page to make sure that all revisions have been added to the manual. B. Components (1) Revision No. indicates the revisions incorporated in this manual. (2) Issue Date is the date of the revision. (3) Comments indicates the level of the revision. (a) New Issue is a new manual distribution. The manual is distributed in its entirety. All the revision dates are the same and no change bars are used. (b) Reissue is a revision to an existing manual that includes major content and/or major format changes. The manual is distributed in its entirety. All the revision dates are the same and no change bars are used. (c) Major Revision is a revision to an existing manual that includes major content or minor format changes over a large portion of the manual. The manual is distributed in its entirety. All the revision dates are the same, but change bars are used to indicate the changes incorporated in the latest revision of the manual. REVISION HIGHLIGHTS 61-00-65 Page 3
(d) Minor Revision is a revision to an existing manual that includes minor content changes to the manual. Only the revised pages of the manual are distributed. Each page retains the date and the change bars associated with the last revision to that page. Revision No. Issue Date Comments Original Nov/95 Total rewrite Revision 1 Aug/96 Minor Revision Revision 2 May/98 Minor Revision Revision 3 Jan/99 Minor Revision Revision 4 Oct/99 Minor Revision Revision 5 Apr/00 Minor Revision Revision 6 May/01 Minor Revision Revision 7 Aug/01 Minor Revision Revision 8 Mar/02 Minor Revision Revision 9 Jun/02 Minor Revision Revision 10 Sep/03 Minor Revision Revision 11 Aug/04 Minor Revision Revision 12 Aug/11 Major Revision Revision 13 Jul/12 Minor Revision Revision 14 Jun/13 Minor Revision Revision 15 Dec/13 Minor Revision Revision 16 Apr/14 Minor Revision Revision 17 Dec/14 Minor Revision Revision 18 Feb/16 Minor Revision Revision 19 Nov/16 Minor Revision Revision 20 Apr/17 Minor Revision Revision 21 Oct/17 Minor Revision REVISION HIGHLIGHTS 61-00-65 Page 4
LIST OF EFFECTIVE PAGES Chapter Page Revision Level Date Cover/Cover Back Cover/Inside Cover Revision Highlights 1 thru 4 Record of Revisions 1 and 2 Rev. 12 Aug/11 Record of Temporary Revisions 1 and 2 Rev. 12 Aug/11 List of Effective Pages 1 thru 4 Table of Contents 1 and 2 Rev. 19 Nov/16 Introduction 1 and 2 Rev. 19 Nov/16 Introduction 3 Rev. 13 Jul/12 Introduction 4 thru 12 Rev. 19 Nov/16 Numerical Index 1-1 and 1-2 Rev. 20 Apr/17 Tool and Equipment Index 2-1 Rev. 19 Nov/16 Tool and Equipment Index 2-2 Rev. 12 Aug/11 Tool and Equipment Index 2-3 and 2-4 Rev. 18 Feb/16 Tool and Equipment Index 2-5 Tool and Equipment Index 2-6 and 2-7 Rev. 12 Aug/11 Tool and Equipment Index 2-8 Rev. 15 Dec/13 Tool and Equipment Index 2-9 Rev. 12 Aug/11 Tool and Equipment Index 2-10 Rev. 16 Apr/14 Tool and Equipment Index 2-11 Rev. 18 Feb/16 Tool and Equipment Index 2-12 Rev. 15 Dec/13 Tool and Equipment Index 2-13 Rev. 19 Nov/16 Tool and Equipment Index 2-14 Rev. 18 Feb/16 Tool and Equipment Index 2-15 thru 2-18 Rev. 20 Apr/17 Tool and Equipment Index 2-19 and 2-20 Alphabetical Index 3-1 and 3-2 Rev. 12 Aug/11 Tool and Equipment List 4-1 Rev. 12 Aug/11 Tool and Equipment List 4-2 Rev. 18 Feb/16 Tool and Equipment List 4-3 thru 4-5 Rev. 12 Aug/11 Tool and Equipment List 4-6 Rev. 18 Feb/16 Tool and Equipment List 4-7 Rev. 14 Jun/13 LIST OF EFFECTIVE PAGES 61-00-65 Page 1
LIST OF EFFECTIVE PAGES Chapter Page Revision Level Date Tool and Equipment List 4-8 and 4-9 Rev. 12 Aug/11 Tool and Equipment List 4-10 Rev. 15 Dec/13 Tool and Equipment List 4-11 Rev. 12 Aug/11 Tool and Equipment List 4-12 Rev. 15 Dec/13 Tool and Equipment List 4-13 Rev. 19 Nov/16 Tool and Equipment List 4-14 Rev. 13 Jul/12 Tool and Equipment List 4-15 Rev. 18 Feb/16 Tool and Equipment List 4-16 Rev. 19 Nov/16 Tool and Equipment List 4-17 thru 4-21 Rev. 12 Aug/11 Tool and Equipment List 4-22 and 4-23 Rev. 20 Apr/17 Tool and Equipment List 4-24 Rev. 15 Dec/13 Tool and Equipment List 4-25 Tool and Equipment List 4-26 Rev. 17 Dec/14 Tool and Equipment List 4-27 and 4-28 Rev. 12 Aug/11 Tool and Equipment List 4-29 Rev. 18 Feb/16 Tool and Equipment List 4-30 Rev. 12 Aug/11 Tool and Equipment List 4-31 Rev. 15 Dec/13 Tool and Equipment List 4-32 thru 4-35 Rev. 12 Aug/11 Tool and Equipment List 4-36 Rev. 18 Feb/16 Tool and Equipment List 4-37 Rev. 14 Jun/13 Tool and Equipment List 4-38 Rev. 15 Dec/13 Tool and Equipment List 4-39 Rev. 20 Apr/17 Tool and Equipment List 4-40 and 4-41 Rev. 12 Aug/11 Tool and Equipment List 4-42 Rev. 18 Feb/16 Tool and Equipment List 4-42.1 and 4-42.2 Tool and Equipment List 4-43 Rev. 18 Feb/16 Tool and Equipment List 4-44 thru 4-57 Rev. 12 Aug/11 Tool and Equipment List 4-58 Rev. 15 Dec/13 Tool and Equipment List 4-59 and 4-60 Rev. 12 Aug/11 Tool and Equipment List 4-61 and 4-62 Rev. 15 Dec/13 Tool and Equipment List 4-63 and 4-64 Rev. 12 Aug/11 LIST OF EFFECTIVE PAGES 61-00-65 Page 2
LIST OF EFFECTIVE PAGES Chapter Page Revision Level Date Tool and Equipment List 4-65 Rev. 15 Dec/13 Tool and Equipment List 4-66 thru 4-69 Rev. 12 Aug/11 Tool and Equipment List 4-70 and 4-71 Rev. 15 Dec/13 Tool and Equipment List 4-72 thru 4-74 Rev. 12 Aug/11 Tool and Equipment List 4-75 Rev. 17 Dec/14 Tool and Equipment List 4-76 thru 4-78 Rev. 12 Aug/11 Tool and Equipment List 4-79 Rev. 18 Feb/16 Tool and Equipment List 4-80 Rev. 12 Aug/11 Tool and Equipment List 4-81 Rev. 15 Dec/13 Tool and Equipment List 4-82 Rev. 18 Feb/16 Tool and Equipment List 4-82.1 and 4.82.2 Rev. 18 Feb/16 Tool and Equipment List 4-83 and 4-84 Rev. 12 Aug/11 Tool and Equipment List 4-85 thru 4-87 Rev. 20 Apr/17 Tool and Equipment List 4-88 and 4-89 Rev. 19 Nov/16 Tool and Equipment List 4-90 Rev. 20 Apr/17 Tool and Equipment List 4-91 Rev. 15 Dec/13 Tool and Equipment List 4-92 thru 4-94 Rev. 12 Aug/11 Tool and Equipment List 4-95 Rev. 18 Feb/16 Tool and Equipment List 4-96 thru 4-98 Rev. 12 Aug/11 Tool and Equipment List 4-99 Tool and Equipment List 4-100 Rev. 15 Dec/13 Tool and Equipment List 4-101 and 4-102 Rev. 19 Nov/16 Tool and Equipment List 4-103 Rev. 16 Apr/14 Tool and Equipment List 4-104 and 4-105 Rev. 12 Aug/11 Tool and Equipment List 4-106 Rev. 19 Nov/16 Tool and Equipment List 4-107 Rev. 12 Aug/11 Tool and Equipment List 4-108 Rev. 19 Nov/16 Tool and Equipment List 4-108.1 and 108.2 Rev. 19 Nov/16 Tool and Equipment List 4-109 Rev. 19 Nov/16 Tool and Equipment List 4-110 and 4-111 Rev. 12 Aug/11 Tool and Equipment List 4-112 Rev. 18 Feb/16 LIST OF EFFECTIVE PAGES 61-00-65 Page 3
LIST OF EFFECTIVE PAGES Chapter Page Revision Level Date Tool and Equipment List 4-113 Rev. 12 Aug/11 Tool and Equipment List 4-114 Rev. 18 Feb/16 Tool and Equipment List 4-115 and 4-116 Rev. 12 Aug/11 Tool and Equipment List 4-117 and 4-118 Rev. 15 Dec/13 Tool and Equipment List 4-119 Rev. 20 Apr/17 Tool and Equipment List 4-120 and 4-121 Rev. 12 Aug/11 Tool and Equipment List 4-122 Rev. 16 Apr/14 Tool and Equipment List 4-123 and 4-124 Rev. 12 Aug/11 Tool and Equipment List 4-125 Rev. 15 Dec/13 Tool and Equipment List 4-126 and 4-127 Rev. 12 Aug/11 Tool and Equipment List 4-128 Rev. 15 Dec/13 Tool and Equipment List 4-129 Rev. 12 Aug/11 Tool and Equipment List 4-130 and 4-131 Rev. 18 Feb/16 Tool and Equipment List 4-132 and 4-133 Rev. 12 Aug/11 Tool and Equipment List 4-134 and 4-135 Rev. 17 Dec/14 Tool and Equipment List 4-136 Rev. 13 Jul/12 Tool and Equipment List 4-137 thru 4-139 Rev. 14 Jun/13 Tool and Equipment List 4-140 Rev. 19 Nov/16 Tool and Equipment List 4-141 thru 4-143 Rev. 14 Jun/13 Tool and Equipment List 4-144 thru 4-146 Rev. 15 Dec/13 Tool and Equipment List 4-147 Rev. 19 Nov/16 Tool and Equipment List 4-148 Rev. 16 Apr/14 Tool and Equipment List 4-149 Rev. 15 Dec/13 Tool and Equipment List 4-150 Rev. 18 Feb/16 Tool and Equipment List 4-151 and 4-152 Rev. 16 Apr/14 Tool and Equipment List 4-153 Rev. 17 Dec/14 Tool and Equipment List 4-154 thru 4-156 Rev. 18 Feb/16 Tool and Equipment List 4-157 Tool and Equipment List 4-158 Rev. 19 Nov/16 Tool and Equipment List 4-159 and 4-160 Rev. 20 Apr/17 LIST OF EFFECTIVE PAGES 61-00-65 Page 4
TE NUMBER PART NUMBER DESCRIPTION VENDOR PAGE TE139-2 AST-2805-2 Torque Wrench Adaptor HP 4-2 TE140 BST-2963 Spinner Support Plate Wrench HP OBS TE141 BST-3044 Clamp Wrench HP 4-50,4-92 TE142 BST-2813 Clamp Nut Wrench HP 4-17 TE143 BST-3032 Open End Wrench HP 4-46 TE144 SC046 Piston Nut Wrench SO 4-25 TE144-1 SC058 Piston Nut Wrench SO 4-25 TE145 n/a Superseded by TE144-1 n/a n/a TE146 BST-2910 Shaft Nut Wrench HP 4-15 TE147 79651407K Vacuum Oil 54996-252 VR 4-1 TE148 BT-461 Spanner Wrench HP 4-62 TE149 AST-2814 Torque Wrench Adaptor HP 4-3 TE150 BST-2860 Torque Wrench HP 4-21 TE151 AST-2915 Torque Wrench Adaptor OBS TE152 AST-2917 Torque Wrench Adaptor HP 4-6 TE153 BST-2921 Torque Wrench Adaptor HP 4-27 TE154 AST-2953 Torque Wrench Adaptor HP 4-7 TE155 AST-2877-1 Torque Wrench Adaptor HP 4-6,4-94 TE156 796540702 Vacuum Hose YA-6407-02 CP 4-1 TE157 BST-10005 Beta Switch Tester HP 4-61,4-92 TE158 79651009A Vacuum Gauge 1009A JC 4-1 TE159 BST-10007 Threaded Headless Pins HP 4-62,4-92 TE160 7965639221 Vacuum Fitting YA-6392-21 CP 4-1 TE161 BST-2974 Erosion Shield Bonding Clamp HP 4-38 TE162 BST-2974-1 Erosion Shield Bonding Clamp HP 4-38 TE163 BST-2974-2 Erosion Shield Bonding Clamp HP 4-38 TE164 BST-2974-3 Erosion Shield Bonding Clamp HP 4-38 TE165 BST-2974-4 Erosion Shield Bonding Clamp HP 4-38 TE166 GTMU121 Universal Socket, 12 Point, 3/8 inch, 1/4 Drive SO 4-92 TE167 n/a n/a n/a n/a TE168 BST-2974-7 Erosion Shield Bonding Clamp HP 4-38 TE169 n/a n/a n/a n/a TE170 n/a n/a n/a n/a TE171 BST-2975 Fit Check Tool HP 4-39 TE172 BST-2975-1 Fit Check Tool HP 4-39 TE173 BST-2975-2 Fit Check Tool HP 4-39 TE174 BST-2975-3 Fit Check Tool HP 4-39 TE175 BST-2975-4 Fit Check Tool HP 4-39 TE176 APS351 Adjustable Spanner Wrench, 1/8 Pin SO 4-92 TE177 BST-2975-6 Fit Check Tool HP 4-39 TE178 BST-2975-7 Fit Check Tool HP 4-39 TOOL AND EQUIPMENT INDEX 61-00-65 Page 2-5
TE NUMBER PART NUMBER DESCRIPTION VENDOR PAGE TE179 n/a n/a n/a n/a TE180 BST-2975-9 Fit Check Tool HP 4-39 TE181 BST-2966 Spinner Support Plate Ream Fixture HP 4-38 TE182 BST-2966-3 Spinner Support Plate Ream Fixture HP 4-38 TE183 BST-2966-4 Spinner Support Plate Ream Fixture HP 4-38 TE184 BST-2966-5 Spinner Support Plate Ream Fixture HP 4-38 TE185 BST-3055 PCU Bearing Installation Tool HP 4-53,4-92 TE186 BST-3055-1 PCU Bearing Installation Tool HP 4-53,4-92 TE187 CST-3000 Initial Erosion Shield Sample Program Kit HP 4-90 TE188 CST-3000-1 Initial Erosion Shield Sample Program Kit HP 4-90 TE189 CST-3000-2 Initial Erosion Shield Sample Program Kit HP 4-90 TE190 CST-3000-3 Initial Erosion Shield Sample Program Kit HP 4-90 TE191 CST-3000-4 Initial Erosion Shield Sample Program Kit HP 4-90 TE192 GFC48A Crowfoot Wrench, Open End with Side Lock Hole, 1 1/2 inch, 3/8 Drive SO 4-92 TE193 CST-3000-6 Initial Erosion Shield Sample Program Kit HP 4-90 TE194 CST-3000-7 Initial Erosion Shield Sample Program Kit HP 4-90 TE195 n/a n/a n/a n/a TE196 CST-3000-9 Initial Erosion Shield Sample Program Kit HP 4-90 TE197 n/a n/a n/a n/a TE198 n/a n/a n/a n/a TE199 n/a n/a n/a n/a TE200 n/a n/a n/a n/a TE201 n/a n/a n/a n/a TE202 GFS161 Deep Well Socket, 12 Point, 1/2 inch, 3/8 Drive SO 4-92 TE203 n/a n/a n/a n/a TE204 n/a n/a n/a n/a TE205 n/a n/a n/a n/a TE206 n/a n/a n/a n/a TE207 BT-1465-1 Floating Reamer HP 4-67 TE207-1 BT-1465-3 Floating Reamer HP 4-67 TE208 BT-1465-2 Floating Reamer HP 4-67 TE208-1 BT-1465-4 Floating Reamer HP 4-67 TE209 n/a n/a n/a n/a TE210 n/a n/a n/a n/a TE211 n/a n/a n/a n/a TE212 n/a n/a n/a n/a TE213 n/a n/a n/a n/a TE214 GFC012 Crowfoot Wrench, Open End, 3/8 in SO 4-94,4-92 TE215 n/a n/a n/a n/a TOOL AND EQUIPMENT INDEX 61-00-65 Page 2-6 Rev. 12 Aug/11
TE NUMBER PART NUMBER DESCRIPTION VENDOR PAGE TE627 BST-2855 Spring Assembly Tool HP 4-159 TE628 BST-2850-1 Threaded Rod HP 4-159 TE629 BST-3004-42A Template HP 4-42.1 TE630 BST-3004-42B Template HP 4-42.1 TE631 CST-3000-42 Erosion Shield Sample Program Kit HP 4-90 TE632 BST-2975-29 Fit Check Tool HP 4-39 TE633 BST-3000-29 Initial Erosion Shield Sample Program Kit HP 4-90 TE634 106964 Assembly Low Pitch Spacer HP 4-160 TE635 BST-2869-1 Spacer HP 4-157 TOOL AND EQUIPMENT INDEX 61-00-65 Page 2-19
(This page is intentionally blank.) TOOL AND EQUIPMENT INDEX 61-00-65 Page 2-20
Piston Nut Wrench Part Number TE Number Description SC046 (SO) TE144 Wrench to tighten A-880-1 Piston Nut on a steel hub turbine propeller. Customer procured. SC058 (SO) TE144-1 Wrench to remove A-880-2A Piston Nut on a steel (Supersedes TE145) hub turbine propeller. Customer procured. Supersedes: B-842, B-842-1, BST-2911, BST-3911-1 APS-205 TOOL AND EQUIPMENT LIST 61-00-65 Page 4-25
Building Buck Components Part Number: BST-2912 (TE125) Building Buck Components, includes items 1 through 9 listed below Item Number Part Number Description 1... BST-2912+ (TE125-1) Spindle Base; Supersedes: B-843-2 (Includes TE85) 2... BST-2912-1 (TE124) Flanged Hub Spindle (Includes TE4) Supersedes: BST-2812 3... BST-2912-2 (TE122) #20 Spline Spindle; not shown 4... BST-2912-3 (TE123) #30 Spline Spindle; not shown 5... BST-2912-4 (TE4) Adapter Ring; Permits mounting of N flange propellers 6... BST-2912-9 (TE2) Adapter; Permits mounting of A flange single acting propellers 7... BST-2912-11 (TE85) Stop Pin; not shown 8... BST-2912-12 (TE127) Mid Pitch Stop; Supersedes: BT-2162; not shown 9... BST-2912-13 (TE327) Blade Angle Stop for -5 Propellers; not shown Also available as necessary (not a part of BST-2912 (TE125): BST-2912-10 (TE80) C Flange Spindle; allow mounting of C flange HD-E6C-3 propeller; not shown BST-2912-17 (TE433) A Flange Spindle; allow mounting of A flange HC-E5A-2 propeller; not shown BST-2912-19 (TE536) H, T, Q, and G Flange Spindle; allow mounting of H, T, Q, and G flange propellers; shown on page 4-148 of this manual BST-2912-22 (TE550) F Flange Bantam Adapter Ring; shown on page 4-153 of this manual Description: Spindle mounts to propeller assembly table CST-2901(-) (TE129) to permit pressurizing of propeller to change pitch. Also permits rotating of the propeller. Obsolete: BST-2912-8 (TE1) Adapter; Allow mounting of C flange single acting propellers; not shown BST-2912-4 Adapter Ring BST-2912-9 Adapter BST-2912-1 Flanged Hub Spindle APS-546 BST-2912+ Spindle Base TOOL AND EQUIPMENT LIST 61-00-65 Page 4-26 Rev. 17 Dec/14
Template (Con't.) Part Number: BST-3004-23A (TE525) 30 inch station of ( )79(A/B)06 BST-3004-23B (TE526) 36 inch station of ( )79(A/B)06 BST-3004-24A (TE527) 30 inch station of ( )76(A/B)01-2 BST-3004-24B (TE528) 36 inch station of ( )76(A/B)01-2 BST-3004-25A (TE529) 30 inch station of ( )75(A/B)01-2 BST-3004-25B (TE530) 36 inch station of ( )75(A/B)01-2 BST-3004-28A (TE563) 24 inch station of NC10245 & NC10320( ) BST-3004-28B (TE564) 42 inch station of NC10245 & NC10320( ) BST-3004-30A (TE571) 24 inch station of 108MH92 BST-3004-30B (TE572) 48 inch station of 108MH92 BST-3004-35A (TE565) 24 inch station of 78D01 BST-3004-35B (TE566) 36 inch station of 78D01 BST-3004-38A (TE596) 24 inch station of 76C03( ) BST-3004-38B (TE597) 36 inch station of 76C03( ) BST-3004-40A (TE621) 30 inch station of ( )NC10904 & ( )NC10905 BST-3004-40B (TE622) 48 inch station of ( )NC10904 & ( )NC10905 BST-3004-41B (TE613) 30 inch station of 76C03( ) BST-3004-42A (TE629) 24 inch station of C79C03-7 BST-3004-42B (TE630) 30 inch station of C79C03-7 Description: Tool to check stations of composite blades. BST-3004 TOOL AND EQUIPMENT LIST 61-00-65 Page 4-42.1
(This page is intentionally blank.) TOOL AND EQUIPMENT LIST 61-00-65 Page 4-42.2
Propeller Assembly Table Part Number: CST-2901-( ) (TE129) Description: Table used to assemble/disassemble propellers. Can order complete propeller assembly table or contact Hartzell Propeller Inc. for information to fabricate. The CST-2901 includes the propeller assembly table and the items listed in the chart below. NOTE: Propeller Assembly Table (Full Size Shown) Pressure gauges included with this propeller assembly table TE129 are subject to calibration drift during shipping because of vibration, shock, etc., and must be re-calibrated by the customer on arrival at the final destination. Qty Item HPI Part No. Description 1 CST-2901 (TE129) Propeller Assembly Table Full Size 1 CST-2901-1 (TE129) Propeller Assembly Table Short 1 CST-2901-2 (TE129) Propeller Assembly Table Full Size W/ Spindle Base, Anti-Rotation Pin 1 CST-2901-3 (TE129) Propeller Assembly Table Short W/ Spindle Base, Anti-Rotation Pin 1 CST-2901-4 (TE129) Propeller Assembly Table Full Size W/ Building Buck Components 1 CST-2901-5 (TE129) Propeller Assembly Table Short W/ Building Buck Components 1 1 1 1 CST-2901+1 Base, Full Size 1 1 1 2 CST-2901-1+1 Base, Short 2 2 2 2 2 2 3 106947 Blade Decal, HPI Oval 2 2 2 2 2 2 4 CST-2901+3 Hanger 1 1 5 BST-2912 (TE125) Building Buck Components (1) (1) 6 BST-2912-12 (TE127) Mid Pitch Adapter (1) (1) 7 BST-2912-1 (TE124) Flanged Hub Spindle (1) (1) 8 BST-2912-4 (TE4) Adapter Ring"N" Flange (1) (1) 9 BST-2912-9 (TE2) "A" Flange Adaptor"C" Flange Adaptor (1) (1) 10 BST-2912-10 (TE80) "C" Flange Adaptor (1) (1) 1 1 11 BST-2912+ (TE125-1) Spindle Base (1) (1) 12 BST-2912-13 (TE327) -5 Blade Angle Stop (1) (1) 1 1 13 BST-2912-11 (TE85) Anti Rotation Pin (1) (1) 14 BST-2912-2 (TE122) #20 Spline Spindle (1) (1) 15 BST-2912-3 (TE123) #30 Spine Spindle 1 1 1 1 1 1 16 CST-2901+5 Pneumatics Anti-rotation Pin Spindle Base TOOL AND EQUIPMENT LIST 61-00-65 Page 4-99
Blade Bearing Press Part Number: DST-2934 (TE93) Description: Press to install the inboard split bearing races and retaining rings onto single shoulder blades. The press also installs the needle roller bearings inside Y, D, and E shank blade bores. Locator Plate NOTE: Does not include the hydraulic power unit. Reference Ball Size Use with Bearing Part Number DST-2934+1 3/8" C-792-( ) D-7745-( ) DST-2934+2 1/2" A-2202-( ) C-7438-( ) C-7075-( ) C-2882-( ) (This space is intentionally blank.) TOOL AND EQUIPMENT LIST 61-00-65 Page 4-100 Rev. 15 Dec/13
C-shank Rolling Conversion Kit Part Number: 106542 (TE594) Description: The C-shank Rolling Conversion Kit is an assembly to convert the Hartzell Propeller Inc. Rolling Machine to roll the Raptor C-shank blades. Part Number Description Quantity 104811 (TE503) Blank, Spacer 1 BST-2869-1 (TE635) Spacer 1 DT-1724+171 (TE598) Base 1 DT-1724+172 (TE599) Ring, Clamp 1 DT-1724+173 (TE600) Pin, Locator 1 Spacer Blank 104811 (TE503) Base DT-1724+171 (TE598) Clamp Ring DT-1724+172 (TE599) Spacer BST-2869-1 (TE635) Locator Pin DT-1724+173 (TE600) TPI-JM-000011 TOOL AND EQUIPMENT LIST 61-00-65 Page 4-157
Shot Peen Masking Tools Part Number: Mask DST-5855+72 (TE601) Mask DST-5855+73 (TE602) Description: Masking tools for the Raptor C-shank. Mask DST-5855+72 (TE601) Mask DST-5855+73 (TE602) TPI--DST-5855+72, TPI--DST-5855+73 Piston Ring Clamp Kit Part Number: 106513 (TE616) For removing the piston ring from piston units C-497 and C-497-1. Description: The piston ring clamp kit includes tools and parts to remove the piston ring from piston units C-497 and C-497-1. The kit contains the following: Hartzell P/N Description Qty 106294 (TE617) Clamp, Ring, Piston 1 106295 (TE618) Base, Clamp 1 106296 (TE619) Washer, Clamp 1 106294 (TE617) 106295 (TE618) 106296 (TE619) TPI--106513 TOOL AND EQUIPMENT LIST 61-00-65 Page 4-158 Rev. 19 Nov/16