ORDIC FIBERGLASS, INC.

Nordic Fiberglass, Inc. Product Catalog 2013 Single & Three Phase Transformer Box Pads Single & Three Phase Sectionalizing Cabinets Hand Holes, Secondary & Meter Pedestals, & More... ORDIC FIBERGLASS, INC. Quality Products for the Electric Utility Industry P.O. Box 27 Warren, MN 56762 Tel: 218-745-5095 Fax: 218-745-4990 www.nordicfiberglass.com

This Page is intended to be blank

Table of Contents Page Table of Contents 3 Warranty 4 Box Pads, 1 Phase Transformer 5 Box Pads, 3 Phase Transformer 6 Box Pads, Air-Insulated Switchgear, Oil-Filled Switchgear 7 Box Pads, Air-Insulated Switchgear with an Access Panel 8 Box Pads, Transformer-Meter-Switch 9 Cabinets, 1 Phase Sectionalizing 11 Cabinets, 2 Phase Sectionalizing 16 Cabinets, 3 Phase Sectionalizing 18 Cabinet Extensions 25 Cabinets, Deferral 26 Cabinets, Sub-Surface Sectionalizing 27 Cabinets, Vacuum Switch 28 Covers, Ground Sleeve 29 Extenders and Adapters 30 Flexi-Flags, Curb, and Cabinet Markers 31 Ground Sleeves, 1 & 3 Phase Sectionalizing 32 Ground Sleeves, Traffi c 33 Hardware & Miscellaneous Accessories 34 Hill Holders 36 Pedestals, Hand Holes 37 Pedestals, Joint Trench 39 Pedestals, Looping 40 Pedestals, Meter 41 Pedestals, Secondary 43 Pedestals, Tap 47 This Page is intended to be blank 50 Page 3

Warranty WARRANTY THE FOLLOWING WARRANTY APPLIES TO ALL FIBERGLASS PRODUCTS SHIPPED AFTER MARCH 1, 1999 Nordic Fiberglass, Inc. warrants all of its products to be free of defects in materials and workmanship for a period of three years from date of purchase when used under normal conditions and for the purpose for which it was designed. In addition, Nordic Fiberglass, Inc. warrants its FIBERGLASS products for a period of thirty years against failure due to loss of strength through degradation when used under normal environmental conditions. Acts of God are excluded. Purchaser s sole remedy for any defect shall be the repair or replacement of the product. Whether the defect is remedied by repair or replacement shall be the decision of Nordic Fiberglass, Inc. and shall constitute the complete fulfi llment of Nordic Fiberglass obligation under this warranty. All expenses related to removal and transportation incurred by the owner of the product in delivering the product to Nordic Fiberglass, Inc. for repair or reinstallation of the repaired or replaced product shall be the responsibility of the product owner. This warranty is expressly in lieu of any other express or implied warranties and Nordic Fiberglass, Inc. makes no other express or implied warranty, including any implied warranty of fi tness or merchant ability. In no case shall Nordic Fiberglass, Inc. be liable for consequential, special or indirect damages resulting from breach of this warranty. Page 4

Box Pads for Single Phase Transformers Box Pads, 1 Phase Transformer CBP-37-43-15A-MG-22x24 GS-37-43-32A-CE-2-MG-26x32 TP-42-42-5-MG-12x20 Installed CBP unit CBP with Transformer CBP units (compression box pad) are manufactured of SMC (Sheet Molding Compound). SMC is a thermosetting compound which is pre-mixed with pigments that are molded into the fiberglass and cannot peel. Fire retardant and UV additives are permanently molded in throughout the laminate. GS units are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using 18 oz. woven roving glass reinforcement for great strength. Munsell green surface coat is applied for superior weather-ability. Accommodates typical single phase transformers ranging from 25kVA up to 167 kva ratings. Optional tie-down brackets are available to hold the transformer in place. Bottom flange provides a stable footing for installation. Benefits: Molded in ribs resist sidewall ground pressures to help prevent sidewall deflection. No costly forms to set up, no cement needs to be poured, the fiberglass box pads reduce installation time by being built ready to go. Box Pads for Single Phase Transformers CBP-37-43-15A-MG-22x24 CBP-37-43-15B-MG-20x20 CBP-37-43-15C-MG-21x12 CBP-37-43-15F-MG-25.5x30 CBP-37-43-24A-MG-22x24 CBP-37-43-24B-MG-20x20 CBP-37-43-24C-MG-21x12 CBP-37-43-24F-MG-26x30 GS-24-37-25-MG-16x24 GS-25-40-18-MG-15.5x11.5 GS-25-40-24-MG-14x10 GS-28-28-15-MG-20x20 GS-34-30-25-MG-22x18 GS-34-34-15A-MG-22x24 GS-34-34-15B-MG-20x20 GS-36-26-24-MG-24x12 GS-36-36-15-MG-22x22 GS-36-36-18-MG-24x24 GS-36-36-24-MG-25x25 GS-36-36-32-MG-25x25 GS-37-43-32A-CE-2-MG-26x32 GS-37-43-32B-CE-2-MG-20x20 GS-37-43-32C-CE-2-MG-22x24 GS-37-43-42A-MG-26x32 GS-37-43-48-MG-25x31 GS-37-46-15A-MG-22x24 GS-37-48-32A-CE-2-MG-26x31 GS-37-52-15-MG-23x24 GS-42-42-18-MG-25x25 GS-42-42-32-MG-25x25 GS-42-48-16-MG-26x12 GS-42-48-18-MG-25x25 GS-42-48-24-MG-26x12 GS-42-48-32C-MG-22x24 GS-42-48-32-MG-26x12 TP-42-42-5B-MG-28x13 TP-42-42-5-MG-12x20 TP-48-48-5-MG-25x13 Page 5

Box Pads, 3 Phase Transformer Box Pads for Three Phase Transformers GS-69-47-36RT-MG-56x16 GS-69-47-18RT-MG-56x16 TP-66-72-5-MG-18x42 3 Phase Box Pad Installation 3 Phase Box Pad Installation RT series box pads for three-phase transformers are available in various heights. Designed for strength without excessive weight. They are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using 18 ounce woven roving glass reinforcement. Multiple layers of chopped and woven roving glass encapsulate plywood and 2x6 s, providing a rigid surface for the transformer oil tank. On the 36 box pads, the 2x4 is encapsulated around the box pad perimeter halfway up the sidewall and vertical ribs are molded into the bottom half on all four sides. The height of the box pads allows for excellent cable training and cable mobility for most three-phase transformers. The box pads are spacious enough to accommodate looping of extra cable. Benefits: No costly forms to set up, no cement needs to be poured, the fiberglass box pads reduce installation time by being built ready to go. In case of elbow failure, the extra looped cable enables the lineperson to use the extra slack for installing a new elbow. Box Pads for Three Phase Transformers GS-111-44-36RT-3O-MG-20x11 GS-67-59-18RT-MG-52x18 GS-72-62-17RT-MG-58X18 GS-84-66-36RT-MG-64x18 GS-111-44-36RT-MG-93x11 GS-67-59-36RT-MG-52x18 GS-72-62-30RT-MG-58X18 GS-86-78-18RT-2X-MG-74x22 GS-47-47-20RT-MG-40x13 GS-67-69-18RT-MG-58x24 GS-72-72-20RT-MG-60x25 GS-86-78-36RT-2X-MG-74x22 GS-54-44-32RT-MG-41x15 GS-67-69-30RT-MG-58x24 GS-72-72-36RT-MG-60x25 TP-48-64-5-MG-12x30 GS-54-52-15RT-MG-41x15 GS-69-47-18RT-MG-56x16 GS-75-47-36RT-MG-58x16 TP-48-72-5-MG-18x42 GS-60-47-36RT-MG-48x15 GS-69-47-36RT-MG-56x16 GS-75-69-18RT-MG-58x18 TP-66-72-5-MG-18x42 GS-65-44-20RT-MG-56x15 GS-69-65-18RT-MG-56x16 GS-75-69-36RT-MG-58x18 TP-72-72-10-MG-60x18 GS-65-44-36RT-MG-56x15 GS-69-65-36RT-MG-56x16 GS-80-54-18RT-MG-60x18 GS-65-56-18RT-MG-56x16 GS-72-56-17RT-MG-58x18 GS-80-54-36RT-MG-60x18 GS-65-56-36RT-MG-56x16 GS-72-56-30RT-MG-58x18 GS-84-66-20RT-MG-64x18 Please be sure to send Nordic Fiberglass a footprint and weight of the transformer in order to determine the appropriate top opening and box pad reinforcement. Page 6

Box Pads, Air-Insulated Switchgear, Oil-Filled Switchgear ORDIC FIBERGLASS, INC. Box Pads for Air-Insulated & Oil-Filled Switchgear GS-75-73-36-MG-67x62 GS-75-73-36-MG-67x62 GS-75-73-36RT-2O-MG Installed box pad Actual installation Nordic box pads for switchgear are available in various sizes. They are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using 18 ounce woven roving glass reinforcement. Munsell green surface coat is applied for superior weatherability and protection from ultraviolet light. These box pads are designed with steps built into the sidewalls for greater vertical strength and resistance to deflection in a buried position. The steps are reinforced with 2x4 s, which are completely encapsulated in additional layers of chopped glass and woven roving glass. Vertical ribs are molded in below the steps for added strength. The RT-2O series of box pads have extra reinforcements to accommodate oil-filled switchgear. These box pads are designed with two top openings to meet the openings of the switch base. A footprint of the switch is required to ensure proper placement of the openings. Bottom flange provides a stable footing for installation. Benefits: Molded in ribs resist sidewall ground pressures to help prevent sidewall deflection. No costly forms to set up, no cement needs to be poured, the fiberglass box pads reduce installation time by being built ready to go. Box Pads for Air-Insulated & Oil-Filled Switchgear GS-106-74-36-SCV-MG-86x12 GS-106-74-48-MG-96.5x62 GS-118-74-36-SCV-MG-96.5x15 GS-124-74-36-MG-114.5x62 GS-125-61-48R-MG-24x47-77.5x20 GS-150-61-48R-MG-24x47-95x20-GSC GS-50-30-20-MG-28x22 GS-50-40-32-MG-41x31 GS-50-50-54-MG-42x42 GS-54-32-26-MG-46x24 GS-54-44-15-MG-42x32 GS-54-44-32-MG-42.5x31 GS-55-37-36-MG-43x25 GS-56-56-20-MG-44x44 GS-57-44-32-MG-47x34 GS-64-37-36-MG-56x29.5 GS-65-44-36-MG-54.5x36 GS-65-44-36-SCV-MG-12x33 GS-65-56-36-MG-50x40 GS-67-61-36-MG-59x51 GS-67-61-48-MG-59x51 GS-69-47-36-MG-61x39 GS-69-65-18-MG-58x51 GS-69-65-36-MG-58x51 GS-72-40-36-MG-52x28 GS-75-45-18-MG-61x31.5 GS-75-45-36-MG-61x31.5 GS-75-48-36-MG-61x31.5 GS-75-69-36-MG-65x59 GS-75-69-36-SCV-MG-58x12 GS-75-73-20-MG-67x62 GS-75-73-36-MG-67x62 GS-77-69-18-MG-66x58 GS-77-69-36-MG-66x58 GS-80-36-36-MG-72x30 GS-80-54-18A-MG-71.5x45.5 GS-80-54-36A-MG-71.5x45.5 GS-80-54-36B-MG-62x34 GS-84-66-36-MG-65x51 GS-84-66-36-SCV-MG-64x12 GS-86-78-18-MG-70.5x63 GS-86-78-36-MG-70.5x63 GS-86-84-36 2 PIECE-MG-73x76 GS-89-84-36 2 PIECE-MG-73x76 GS-96-54-36-MG-86x44 GS-96-67-48-MG-59x51-59x24-GSC GS-75-47-36RT-2O-MG GS-75-73-36RT-2O-MG GS-86-78-36RT-2O-MG Page 7

Box Pads, Air-Insulated Switchgear with an Access Panel ORDIC FIBERGLASS, INC. Box Pads for Air-Insulated Switchgear with an Access Panel Designed to accommodate various models of airfilled switchgear. GS-96-67-48-MG-59x51-59x24-GSC is designed to accommodate S&C PMH-6 thru PMH-19 air-filled switchgear in the 15kV base size. GS-125-61-48R-MG-24x47-77.5x20-GSC and GS- 150-61-48R-MG-24x47-95x20-GSC box pads are designed to accommodate large G&W air-filled switchgear. Nordic Fiberglass requires a footprint of your airfilled switchgear to determine the correct box pad for your application. Access panel allows entry into the box pad in order to feed underground cables to the switch. Cover is secured with four penta-head bolts, two of these are inside a metal security case for added protection and padlocking. Cover includes the lettering, WARNING! ELECTRIC HAZARD ENTRY PROHIBITED Cover has down-turned lips around three sides of the cover s perimeter for extra security. GS-96-67-48-MG-59x51-59x24-GSC Benefits: Access panel allows a lineperson to enter the box pad and pull cable up to the terminals. In case of an electrical fault or blown elbow, the extra room inside the interior of the box pad allows the lineperson to enter and repair the fault or damaged elbow. GS-125-61-48R-MG-24x47-77.5x20-GSC GS-150-61-48R-MG-24x47-95x20-GSC Page 8

Transformer/Meter/Switch Box Pad Box Pads, Transformer-Meter-Switch GS-37-39-15-MP-MG-22x22 GS-37-39-15-MP-MG-22x22 installed GS-37-39-24-MP-MG-22x22 GS-37-39-15-SP-MG-22x22 Meter Pedestal/Box Pad GS-37-39-15-MP-MG-22x22 & GS-37-39-24-MP-MG-22x22 Box pads available in 15 and 24 heights accommodate single phase transformers ranging from 25kVA up to 167kVA. Provides a raceway between the transformer and the meter. In case of an elbow failure, the extra cable slack in the box pad s cavity allows the lineperson to quickly attach a new elbow and restore service. Install up to 2 meter enclosures on the outside walls of the MPP meter pedestal. Up to three secondary connectors can be installed on the inside walls of the MPP unit. Large expansive door on the MPP meter pedestal allows easy access inside the pedestal. Penta-head bolt and provisions for pad locking on the MPP give it a double security feature. This meter & box pad CAN T convert to a secondary pedestal/box pad combination. (See part number below) Meter and box pad are shipped separately, assembly is required. Secondary Pedestal/Box Pad GS-37-39-15-SP-MG-22x22 15 high box pad accommodates single phase transformers ranging from 25kVA up to 167kVA. Provides a raceway between the transformer and the secondary pedestal. Accommodates free standing connectors. Accommodates Nordic s connector bracket with optional 350 or 600MCM connectors. Shown without cover Connector bracket sold and shipped separately, assembly is required. Can be converted to a meter pedestal configuration. (Please contact the factory for details) Page 9

Transformer/Meter/Switch Box Pad GS-37-52-15-TMS-MG GS-72-40-18-TMS-MG GS-37-52-15-TMS-MG with single phase transformer & meter GS-80-36-36-2O-MG-TS GS-80-36-36-2O-MG-TS with secondary tap pedestal bolted to adapter and a single phase transformer. GS-37-52-15-TMS-MG & GS-72-40-18-TMS-MG One complete unit designed for a single phase transformer and one meter/switch. Box pad allows for extra looping of primary and secondary cables. In case of an elbow failure, the extra cable slack allows the lineperson to quickly attach a new elbow and restore service. Provides a raceway between the transformer and meter. Alternative Energy Uses: Facilities using supplemental energy system (wind energy) can switch and meter their power with their own energy provider. Allows for Net Metering of an energy generator (wind turbine). Cost effective for alternative energy generating utility customers and businesses. Nordic Box Pads provide the platform for harvesting alternative energy sources. GS-80-36-36-2O-MG-TS Two 22 x 24 top openings accommodates two pieces of electrical equipment at the same time. Provides a raceway between the transformer and enclosure. 80 long x 36 wide top surface area enables a wide variety of equipment to be installed on this TMS box pad. Install Nordic single phase cabinets, single phase transformers, or other various pieces of equipment below: Single phase transformer and GSC-36-36-MG cover. Single phase sectionalizing cabinet and single phase transformer. Single phase transformer and GSA-36-36-MG-25x10 adapter plate. Secondary tap pedestal bolted to GSA-36-36-MG-25x10 adapter plate and sing phase transformer. Page 10

Cabinets, 1 Phase Sectionalizing 15/25kV 200Amp Single Phase Sectionalizing Cabinets Rust free fiberglass construction and stainless steel hardware. The exterior Munsell green coating which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze pentahead bolt provides double locking. Stainless steel self locking cam arm holds lid open. Optional copper grounding is available. Typically installed as a one piece unit, the customer can unbolt the cabinet from the ground sleeve thus enabling the ground sleeve to be installed during construction without subjecting the cabinet to accidental damage. After construction is over, the cabinet can be installed on the ground sleeve. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. ND-22022 Series: Two-piece design: Cabinet is produced of SMC, (Sheet Molding Compound). Ground sleeve is produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. Hot-dipped galvanized MP-125 mounting plate accommodates a 2, 3, or 4 pt., 15/25 kv, 200/600Amp junction with U-straps, except Cooper 35kV. Does not accommodate 200A taps off of the 600A junction. Below parking allows for stand-offs or feed throughs to be installed. ND-23222 Series: Two-piece design: Cabinet and ground sleeve are produced of fi reretardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. Hot-dipped galvanized MP-112 mounting plate accommodates a 2, 3, or 4 pt., 15/25 kv, 200/600Amp junction with U-straps, except Cooper 35kV. In-line parking allows for stand-offs or feed throughs to be installed. ND-2202248-MG-125-X-X ND-2322248-MG-112-X-X 15/25kV 200Amp Single Phase Sectionalizing Cabinets Parking Width Cabinet Height Hot Stick Operating ND-2202248-MG-125-X-X Below 21 21 48 22 ND-2322248-MG-112-X-X In-Line 32.5 32.5 48 20.5 Recommended Burial Finish grade approximately 6 below locking system. Page 11

15/25/35kV 600Amp Single Phase Sectionalizing Cabinet ND-322864-MG-PA38-X-X Rust free fiberglass construction and stainless steel hardware. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Optional copper grounding is available. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. One-piece design, ground sleeve is part of the cabinet. Aluminum PA/PB 38 mounting plate accommodates a single 15/25/35kV 200/600Amp junction with U-straps, (accommodates 200A taps), including Cooper 35kV 200A/600A junctions. The sliding rail on the PA38 or PB38 allows for stand-offs or feed throughs to be installed on the stainless steel parking stands either above or below. Benefits: Pulling elbows with a hot stick is made easier with the adjustable 12-20 mounting bracket found on the PA or PB38 mounting plates. Rotational lid rotates on pivot bolts creating a lower center of gravity that reduces the force required to open the cabinet. The wide open lid allows cable pulling equipment to be used inside of the cabinet with no interference. Hot-stick operators have open access to elbows with no lid interference from the top, front, or sides. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND-322864-MG-PA38-X-X 15/25/35kV 600Amp Single Phase Sectionalizing Cabinet Parking Width Cabinet Height Hot Stick Operating ND-322864-MG-PA38-X-X Above 38 29.5 64 25.5 Recommended Burial Finish grade approximately 6 below locking system. Page 12

15/25kV 200Amp GS Mount Single Phase Sectionalizing Cabinets ND-301830-MG-102A-X-X & ND-301830H-MG-102A-X-X Series Rust free fiberglass construction and stainless steel hardware. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand layup using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze pentahead bolt provides double locking. Optional copper grounding is available. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. Two-piece design: ND-301830-MG-102A-X-X & ND-301830H-MG-102A-X-X require a ground sleeve. Cabinet and ground sleeve are shipped separately and require assembly upon receipt (hardware included). Optional Ground Sleeves: CGS-30-18-18-MG-21x10 GS-30-18-24-MG-20x9 GS-30-18-30-MG-21x10 Hot-dipped galvanized MP-102A mounting plate (also available in stainless steel) accommodates a 2, 3, or 4 pt., 15/25 kv, 200/600Amp junction with U-straps, except Cooper 35kV. In-line parking allows for stand-offs or feed throughs to be installed. Does not accommodate 200A taps off of the 600A junction. ND-301830-MG-102A-X-X includes a lid, this lid is attached to the top fl ange of the cabinet with an interlocking stainless steel channel. ND-301830H-MG-102A-X-X has a (H) hinged lid, includes a self locking stainless steel cam arm which holds the lid open. 15/25kV 200Amp Pad or GS Mount Cabinets Parking Width Cabinet Height Hot Stick Operating ND-301830-MG-102A-X-X In-Line 30 19.5 31 19 ND-301830H-MG-102A-X-X In-Line 30 19.5 31 19 Recommended Burial GS Required ND-301830-MG-102A-X-X 102A X ND-301830H-MG-102A-X-X H-Hinged Page 13

15/25kV 200Amp Pad Mount & Direct Bury Sectionalizing Cabinets Rust free fiberglass construction and stainless steel hardware. One-piece design, ground sleeve is part of the cabinet. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. Hot-dipped galvanized MP-101 mounting plate (also available in stainless steel) accommodates a 2, 3, or 4 pt., 15/25 kv, 200/600Amp junction with U-straps, except Cooper 35k. Below parking allows for stand-offs or feed throughs to be installed. Does not accommodate 200A taps off of the 600A junction. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Stainless steel self locking cam arm holds lid open. Stainless steel continuous hinge connects the lid to the cabinet. Optional copper grounding is available. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. ND-120-MG-101-X-X: ND-120-MG-101-X-X is used for pad-mount installations. Cabinet anchor brackets (4x) are shipped attached to the mounting plate for pad mounting. Concrete anchoring hardware is not included. ND-130-MG-101-X-X & ND-150-MG-101-X-X: ND-130 and ND-150 cabinets are used for direct bury installations. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND-120-MG-101-X-X ND-130-MG-101-X-X 15/25kV 200Amp Pad & Single Sectionalizing Cabinets (Direct Bury) Parking Width Cabinet Height Hot Stick Operating Recommended Burial ND-120-MG-101-X-X Below 23.5 25.5 35 22 Pad Mount ND-130-MG-101-X-X ND-150-MG-101-X-X Below Below 24 23.5 24.5 25.5 37.5 50 20.5 22 Finish grade approximately 6 below locking system. ND-150-MG-101-X-X Page 14

15/25kV 200Amp Single Phase Sectionalizing Cabinets ND-3624 Series: Rust free fiberglass construction. One-piece design, ground sleeve is part of the cabinet. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. Hot-dipped galvanized MP-110 mounting plate accommodates a 2, 3, or 4 pt., 15/25 kv, 200/600Amp junction with U-straps, except Cooper 35kV. In-line parking to allow for stand-offs or feed throughs to be installed. Does not accommodate 200A taps off of the 600A junction. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Optional copper grounding is available. ND-362436-MG-110 X-X can be used for pad-mount or direct bury installations. Concrete anchoring hardware is not included. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. Benefits: Rotational lid rotates on pivot bolts creating a lower center of gravity that reduces the force required to open the cabinet. The wide open lid allows cable pulling equipment to be used inside of the cabinet with no interference. Hot-stick operators have open access to elbows with no lid interference from the top, front, or sides. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND-362436-MG-110-X-X ND-362442-MG-110-X-X ND-362454-MG-110-X-X 15/25kV 200Amp Single Phase Sectionalizing Cabinets Parking Width Cabinet Height Hot Stick Operating Recommended Burial ND-362436-MG-110-X-X In-Line 36.5 23 36.5 23 Pad ND-362442-MG-110-X-X ND-362454-MG-110-X-X In-Line In-Line 36.5 36.5 23 23 42.5 55 23 23 Finish grade approximately 6 below locking system. Page 15

Cabinets, 2 Phase Sectionalizing 15/25kV 200Amp Two Phase Sectionalizing Cabinets ND-3624 Series: Rust free fiberglass construction and stainless steel hardware. One-piece design, the ground sleeve is part of the cabinet. Cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. Two hot-dipped galvanized MP-101 mounting plates (also available in stainless steel) accommodate up to two, 2, 3, or 4 pt., 15/25 kv, 200/600Amp junctions with U-straps, except Cooper 35kV. Does not accommodate 200A taps off of the 600A junction. The two MP-101 mounting plates allows for stand-offs or feed throughs to be installed below the junction. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Optional copper grounding is available. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. Benefits: Rotational lid rotates on pivot bolts creating a lower center of gravity that reduces the force required to open the cabinet. The wide open lid allows cable pulling equipment to be used inside of the cabinet with little interference. Hot-stick operators have open access to elbows with no lid interference from the top, front, or sides. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND-362436-MG-2101-X-X 2101 XX ND-362442-MG-2101-X-X ND-362454-MG-2101-X-X 15/25kV 200Amp Two Phase Sectionalizing Cabinets Parking Width Cabinet Height Hot Stick Operating ND-362436-MG-2101-X-X Below 36.5 23 36.5 23 ND-362442-MG-2101-X-X Below 36.5 23 42.5 23 ND-362454-MG-2101-X-X Below 36.5 23 55 23 Recommended Burial Finish grade approximately 6 below locking system. Page 16

15/25kV 200Amp Two Phase Sectionalizing Cabinets ND-2422850-MG-2125-X-X: Rust free fiberglass construction and stainless steel hardware. Two-piece design: Cabinet and ground sleeve are produced of fireretardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. Two hot-dipped galvanized MP-125 mounting plates (also available in stainless steel) accommodate up to two, 2, 3, or 4 pt., 15/25 kv, 200/600Amp junctions with U-straps, except Cooper 35kV. Does not accommodate 200A taps off of the 600A junctions. The two MP-125 mounting plates allows for stand-offs or feed throughs to be installed below the junction. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Stainless steel self locking cam arm holds lid open. Optional copper grounding is available. Typically installed as a one piece unit, the customer can unbolt the cabinet from the ground sleeve thus enabling the ground sleeve to be installed during construction without subjecting the cabinet to accidental damage. After construction is over, the cabinet can be installed on the ground sleeve. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. Benefits: The wide open lid allows cable pulling equipment to be used inside of the cabinet with little interference. Hot-stick operators have open access to elbows with no lid interference from the top, front, or sides. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND-2422850-MG-2125-X-X 15/25kV 200Amp Two Phase Sectionalizing Cabinet Parking Width Cabinet Height Hot Stick Operating ND-2422850-MG-2125-X-X Below 42 28.5 50 25.5 Recommended Burial Finish grade approximately 6 below locking system. Page 17

Cabinets, 3 Phase Sectionalizing 15kV 200Amp Three Phase Sectionalizing Cabinets Rust free fi berglass construction. Nordic cabinets are produced of fi re-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Stainless steel continuous hinge connects the lid to the cabinet. One stainless steel self locking cam arm and prop arm hold the lid open. Optional copper grounding is available. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. ND-315-MG-2A5A-X-X: One-piece design for the ND-315, ground sleeve is part of the cabinet. Hot-dipped galvanized MP-2A5A mounting plate (also available in stainless steel) accommodates up to three 2, 3 or 4 pt., 15kV 200A loadbreak junctions with U-straps. In-line parking allows for parking stand-offs or 2 pt. feedthroughs on either side of the mounting plate. ND-2315-MG-2A5A-X-X: Two-piece design for the ND-2315. It can also be used for pad-mount applications without the ground sleeve. Hot-dipped galvanized MP-2A5A mounting plate (also available in stainless steel) accommodates up to three 2, 3 or 4 pt., 15kV 200A loadbreak junctions with U-straps. In-line parking allows for parking stand-offs or 2 pt. feedthroughs on either side of the mounting plate. Benefits: The cabinet s eyebolts allow the lineperson to simply hook-up the direct burial cabinet, position it over the cables, and place it in the excavated area. ND-315-MG-2A5A-X-X 15kV 200Amp Three Phase Sectionalizing Cabinets Parking Width Cabinet Height Hot Stick Operating Recommended Burial ND-315-MG-2A5A-X-X In-Line 70.5 17.5 48 15.5 Finish grade approximately ND-2315-MG-2A5A-X-X In-Line 70.5 17.5 53 15.5 6 below locking system. ND-2315-MG-2A5A-X-X Page 18

15/25kV 200Amp Three Phase Sectionalizing Cabinets Rust free fi berglass construction. One-piece design, ground sleeve is part of the cabinet. Nordic cabinets are produced of fi re retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Optional copper grounding is available. One stainless steel self locking cam arm and prop arm hold the lid open. Stainless steel continuous hinge connects the lid to the cabinet. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. ND-250-MG-101-X-X: ND-250-MG-101-X-X is used for pad-mount installations. Cabinet anchor brackets (4x) are shipped attached to the mounting plate for pad mounting. Concrete anchoring hardware is not included. ND-330-MG-101-X-X, ND-350-MG-101-X-X, ND-360-MG-101-X-X: Hot-dipped galvanized MP-101 mounting plate (also availabe instainless steel) accommodates up to three 2, 3, or 4 pt., 15/25kV 200A loadbreak junctions with U-straps, except Cooper 35kV. Does not accommodate 200A taps off of the 600A junctions. (Includes ND-250) Below parking on the MP-101 allows for parking stand-offs or 2 pt. feedthroughs on either side of the mounting plate. Benefits: The cabinet s eyebolts allow the lineperson to simply hook-up the direct burial cabinet, position it over the cables, and place it in the excavated area. 15/25kV 200Amp Three Phase Sectionalizing Cabinets Parking Width Cabinet Height Hot Stick Operating Recommended ed Burial ND-330-MG-101-X-X Below 53.5 26.5 36 19 Finish grade ND-350-MG-101-X-X Below 53.5 26 48 23 approximately 6 below locking ND-360-MG-101-X-X Below 53.5 26 54 23 system. ND-250-MG-101-X-X Below 53.5 26 34.5 23 Pad-Mount ND-250-MG-101-X-X ND-330-MG-101-X-X X ND-350-MG-101-X-X X ND-360-MG-101-X-X Page 19

15/25/35kV 600Amp Three Phase Sectionalizing Cabinets ND-430-MG-101-X-X, ND-450-MG-101-X-X Rust free fi berglass construction. One-piece design for the ND-430 and ND-450, ground sleeve is part of the cabinet. Nordic cabinets are produced of fi re-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Optional copper grounding is available. Two stainless steel self locking cam arms hold the lid open. Stainless steel continuous hinge connects the lid to the cabinet. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. Hot-dipped galvanized MP-101 mounting plate,(also available in stainless steel) accommodates up to three 2, 3 or 4 pt., 15/25/35kV 200A and 600A loadbreak junctions with U-straps, except for Cooper 35kV. Optional hot-dipped galvanized MP-10135 mounting plate, (also available in stainless steel) accommodates up to three 2, 3, or 4 pt., 35kV 600Amp deadbreak junctions with U-straps from Cooper. Accommodates 200A taps off of the 600A junctions. Below parking allows for stand-offs or feed throughs to be installed. ND-450 has an optional 18 or 36 high extension for extra cable bending radius. Benefits: The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area for a simple installation. ND-430-MG-101X-X 15/25/35kV 600Amp Three Phase Sectionalizing Cabinets Parking Width Cabinet Height Hot Stick Operating Recommended Burial ND-430-MG-101-X-X Below 68.5 29.5 53 25.5 Finish grade approximately ND-450-MG-101-X-X Below 68.5 29.5 64.5 29 6 below locking system. ND-450-MG-101X-X Page 20

15/25kV 200Amp Three Phase Roto-Cab Sectionalizing Cabinets ND-5524 Series Rust free fi berglass construction. One-piece design for the ND-5224 Series cabinets, ground sleeve is part of the cabinet. Nordic cabinets are produced of fi re-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Optional copper grounding is available. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. Hot-dipped galvanized MP-101 mounting plate accommodate up to three 2, 3 or 4 pt., 15/25kV 200/600A loadbreak junctions with U-straps. Does not accommodate 200A taps off of the 600A junctions. MP-101 below parking allows for stand-offs or feed throughs to be installed. MP-152, PA58, PB58 mounting plates accommodate up to three 2, 3 or 4 pt., 15/25kV 200A loadbreak junctions with U-straps. The sliding rail on the 152 and PA58 allows for stand-offs or feed throughs to be installed on the stainless steel above parking stands, or the below parking stands on the PB58. Benefits: The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area for a simple installation. ND-552436-MG-152-X-X ND-552436-MG-101-X-X ND-552436-MG-PA58-X-X X ND-552442-MG-101-X-X ND-552442-MG-152-X-X & ND-552442-MG-PA58-X-X X 15/25kV 200Amp Three Phase Sectionalizing Cabinets Parking Width Cabinet Height Hot Stick Operating Recommended Burial ND-552436-MG-101-X-X Below 55.5 23 36 23.5 ND-552436-MG-152-X-X Above 55.5 23 36 23.5 ND-552436-MG-PA58-X-X Above 55.5 23 36 21.5 ND-552442-MG-101-X-X Below 55.5 23 42 23.5 ND-552442-MG-152-X-X Below 55.5 23 42 23.5 ND-552442-MG-PA58-X-X Above 55.5 23 42 23.5 ND-552454-MG-101-X-X Below 55.5 23 54 23.5 ND-552454-MG-152-X-X Above 55.5 23 54 23.5 ND-552454-MG-PA58-X-X Above 55.5 23 54 21.5 Finish grade approximately 6 below locking system. ND-552454-MG-101-X-X ND-552454-MG-152-X-X & ND-552454-MG-PA58-X-X X Page 21

15/25kV 200 and 15/25/35kV 600Amp Three Phase Roto-Cab Sectionalizing Cabinets Rust free fiberglass construction. Two-piece design for the ND-2562448 and ND-2722850. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Optional copper grounding is available. Two stainless steel self locking cam arms hold the lid open. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. ND-2562448-MG-101-X-X & ND-2562448-MG-152-X-X: Hot-dipped galvanized MP-101 & MP-152 mounting plates accommodates up to three 2, 3, or 4 pt., 15/25kV 200A loadbreak junctions with U-straps. Does not accommodate 200A taps off the 600A junctions. MP-101 below parking allows for stand-offs or feed throughs to be installed. MP-152 above parking allows for stand-offs or feed throughs to be installed. MP-152 plate can be rotated horizontally for easy junction installation. ND-2722850: Hot-dipped galvanized MP-168 mounting plate accommodates up to three 2, 3, or 4 pt., 15/25/35kV 200A loadbreak junctions. It also accommodates 200A taps off of the 600A junctions. MP-168 above parking allows for stand-offs or feed throughs to be installed. MP-168 mounting plate can be rotated horizontally for easy junction installation. Benefits: The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. Two-Piece 15/25kV 200Amp Three Phase Sectionalizing Cabinets Parking Width Cabinet Height Hot Stick Operating ND-2562448-MG-101-X-X Below 56 24 48 25 ND-2562448-MG-152-X-X Above 56 24 48 24 Two-Piece 15/25/35kV 600Amp Three Phase Sectionalizing Cabinets ND-2722850-MG-168-X-X Above 72 28 50 28 Recommended Burial Finish grade approximately 6 below locking system. ND-2562448-MG-101-X-X ND-2562448-MG-152-X-X ND-2722850-MG-168-X-X Page 22

15/25/35kV 600Amp Three Phase Roto-Cab Sectionalizing Cabinets Rust free fi berglass construction. One-piece design, ground sleeve is part of the cabinet. Nordic cabinets are produced of fi re-retardant resin and a combination of chopped glass spray-up and hand layup using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Optional copper grounding is available. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. ND-6830 Series: Aluminum PA71 or PB71 mounting plate accommodates up to three 2, 3 or 4 pt., 15/25/35 kv 200A or 600A junctions with U-straps (accommodates 200A taps), including Cooper 35 kv 200A/600A junctions. Accommodates 200A taps off of the 600A junctions. The sliding rail on the PA71 or PB71 allows for stand-offs or feed throughs to be installed on the stainless steel parking stands either above (PA71) or below (PB71). ND-683054 has an optional 18 or 36 high extension for extra cable bending radius. Benefits: The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND-683042-MG-PA71-X-X 15/25/35kV 600Amp Three Phase Sectionalizing Cabinets Parking Width Cabinet Height Hot Stick Operating Recommended Burial ND-683042-MG-PA71-X-X Above 68.5 30 42 26.5 Finish grade approximately ND-683054-MG-PA71-X-X Above 68.5 30 53.5 26.5 6 below locking system. ND-683054-MG-PA71-X-X Page 23

ND-325 (Standard) & (Multi-Point Junction Cabinet) Rust free fiberglass construction and stainless steel hardware. One-piece design, ground sleeve is part of the cabinet. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Optional copper grounding is available. Two stainless steel self locking cam arms hold the lid open. Stainless steel continuous hinge connects the lid to the cabinet. Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard. Standard: ND-325-MG-2C5A-X-X: ND-325-MG-2C5A-X-X Hot-dipped galvanized MP-2C5A mounting plate in the ND-325, (also availabe in stainless steel) accommodates up to three 2, 3, or 4 pt., 15/25kV 200A loadbreak junctions with U-straps. Does not accommodate 200A taps off of the 600A junctions. In-line parking on the MP-2C5A allows for parking stand-offs or 2 pt. feedthroughs on either side of the mounting plate. Multi-Point: ND-325-MG-S102CX-X-X, ND-325-MG-X-X-X Accommodates a variety of 5 and 6 way 15/25/35kV multiple point junctions with 4 interface spacing from a variety of manufacturers including Elastimold, Hubbell, G&W, and Cooper linear junctions. (Check out our website for junction accommodations) ND-325-MG-S102CX-6252B-W3B Junctions without parking stands can either be mounted to a mounting plate or mounted to the cabinet s fiberglass mounting board with their own mounting bracket. Multi-Point junctions allow for different configurations of 200A and 600A interfaces for either load or dead break elbows. Does not accommodate 200A taps off of the 600A junctions. Benefits: The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND-325 Cabinet Mounting Plate Parking Stands Mounting Board Width Hot Stick Operating Cabinet Height ND-325-MG-2C5A-X-X 2C5A In-Line 85 22 48 ND-325-MG-S102CX-X-X S102CX Below 85 22 48 ND-325-MG-X-X-X Based on Junction Below 85 22 48 ND-325-MG-X-53594-W3B Page 24

Cabinet Extensions Cabinet Extensions Used extensively in wind farm applications where large diameter cable needs a large expansive area for bending and cable training. Cabinet extensions extend the height of the cabinet to allow for more cable bending radius. The extensions allow for extra cable looping. In case of an elbow failure, the damaged elbow and cable can be removed and the extra slack can be used to attach a new elbow. 18 or 36 high cabinet extensions are available for most of Nordic s three phase sectionalizing cabinets. Greater anchoring stability is obtained with an extension. Cabinets and extensions bolt to the bottom sides of the cabinets, (cabinets and extensions shipped separately). Bolting hardware included with the extensions. ND-450-MG-101-X-X ND-450-MG-18EXT ND-450-MG-101-X-X ND-450-MG-36EXT ND-450-MG-101-X-X mounted to ND-450-MG-36EXT ND-450-MG-101-X-X mounted to ND-450-MG-18EXT 18 or 36 high cabinet extensions are available for most of our three phase sectionalizing cabinets. Allows for extra cable training and greater anchoring stability. Base Width Base Burial Per Pallet ND-325-MG-18EXT 18 H Ext. for ND-325 123 56 18 12 ND-350-MG-18EXT 18 H Ext. for ND-350 87 60 18 8 ND-350-MG-36EXT 36 H Ext. for ND-350 93.5 66.5 36 8 ND-403264-MG-18EXT 18 H Ext. for ND-403264 73.5 64.5 18 7 ND-403264-MG-36EXT 36 H Ext. for ND-403264 81.5 72.5 36 7 ND-450-MG-18EXT 18 H Ext. for ND-450 101.5 61.5 18 12 ND-450-MG-36EXT 36 H Ext. for ND-450 114 72 36 8 ND-552454-MG-18EXT 18 H Ext. for ND-552454 91 65 18 13 ND-552454-MG-36EXT 36 H Ext. for ND-552454 96.5 70.5 36 8 ND-683054-MG-18EXT 18 H Ext. for ND-683054 101.5 61.5 18 12 ND-683054-MG-36EXT 36 H Ext. for ND-683054 114 72 36 8 Page 25

Cabinets, Deferral ORDIC FIBERGLASS, INC. Transformer Deferral Cabinets ND-202224-MG-125-X-X Cabinet is produced of SMC, (Sheet Molded Compound). Hot-dipped galvanized MP-125 mounting plate accommodates up to two, 2, 3, or 4 pt., 15/25 kv, 200/600Amp junctions with U-straps, except Cooper 35kV. Does not accommodate 200A taps off of the 600A junction. Install it on any CBP A series or GS-37-43 A series box pads. Stainless steel cabinet bolting hardware is included with the cabinet. ND-202224 cabinet weighs only 65 lbs., so one person can install it. When transformer is ready to be installed, remove the ND-202224 cabinet and install the transformer. Either store the ND-202224 or install it for another deferral application thereby saving money on buying a new transformer. ND-202224-MG-125-X-X attached to CBP-37-43-15A-MG-22x24 Other deferral cabinets listed below: ND-28-MG-103-X-X ND-37-MG-102C-X-X & ND-37H-MG-102C-X-X ND-250-MG-101-X-X ND-301830-MG-102A-X-X ND-38-MG-S108-X-X Single Phase 15/25/kV 200Amp Deferral Cabinets GS-Ground Sleeve Parking Page 26 Width Cabinet Height Hot Stick Operating Recommended Burial ND-202224-MG-125-X-X Below 21 21 24 22 ND-28-MG-103-X-X (GS w/22 x24 openings) In-Line 25 29 22 29 Finish grade ND-37-MG-102C-X-X (GS w/22 x24 openings) In-Line 37 29.5 22 29.5 approximately ND-37H-MG-102C-X-X (H=Hinged) In-Line 37 29.5 22 29.5 6 below locking system ND-301830-MG-102A-X-X In-Line 30 19.5 30.5 19 with ground Single Phase 15/25/35kV 600Amp Deferral Cabinets ND-38-MG-S108-X-X (GS w/26 x32 openings) In-Line 37.5 37.5 23 37 sleeve. Three Phase 15/25kV 200Amp Deferral Cabinets ND-250-MG-101-X-X Below 53.5 26 34.5 23 Pad-Mount

Cabinets, Sub-Surface Sectionalizing 15/25kV 200Amp Sub-Surface Sectionalizing Cabinets Rust free fiberglass construction and stainless steel hardware. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. These box pads are heavy duty 1/4 thick, produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using 18 ounce woven roving glass reinforcement. The SSMP-103 mounting plate has in-line parking to allow for stand-offs or feed throughs to be installed. Optional copper grounding is available. The covers have a 2 down-turned lip around the outer perimeter for added security. Single-Phase The GSLBJ-363632-MG-S103-X-X is designed for sectionalizing or deferral with subsequent installation of a single-phase transformer. Stainless steel SSMP-103 mounting plate accommodates all 15/25kV, 200/600A junctions with U-straps, except Cooper 35 kv. Does not accommodate 200A taps off of the 600A junctions. Four brass penta-head recesses are installed, with four 3/8 x 1 1/2 stainless steel penta-head bolts included, for securing the cover to the box pad. Three-Phase GSLBJ-803636-MG-S103-X-X will accommodate three 2, 3, or 4-point 15/25kV, 200A junctions with U-straps. The GSLBJ-805436-MG-S103-X-X will accommodate three 2, 3, or 4-point 15kV or 25kV 200/600A loadbreak junctions with U-straps, except Cooper 35kV. GSLBJ-805436-MG-S103-X-X will accommodate 200A taps off of the 600A junctions. Six brass penta-head recesses are installed, with six 3/8 x 1 1/2 stainless steel penta-head bolts included, for securing the cover to the box pad. 15/25kV 200Amp Single Phase Sectionalizing Cabinets Parking Accommodates 2-4 pt. 15/25kV 200Amp LBJ s Mounting Board Width Hot Stick Operating Height Mounting Board Angle GSLBJ-363632-MG-S103-X-X In-Line Yes 23.5 30 32 30 GSLBJ-803636-MG-S103-X-X In-Line Yes 72 28 36 20 GSLBJ-805436-MG-S103-X-X In-Line Yes 72 45 36 20 GSLBJ-363632-MG-S103-X-X GSLBJ-803636-MG-S103-X-X GSLBJ-805436-MG-S103-X-X Page 27

Cabinets, Vacuum Switch Vacuum Interrupter Switch Cabinets Rust free fiberglass construction and stainless steel hardware. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double locking. Cabinet with interrupter gives the customer an option for line fault protection. Optional copper grounding is available. ND-3624 Series Strong strut bracket supports horizontally mounted interrupter switches. Stationary bracket accommodates Elastimold bolt patterns. (Brackets do not include interrupter mounting hardware) Cabinet extensions are available in 18 or 36 heights for more cable bending radius for the ND-362454-MG-UNI2-X-X model. ND-362436-MG-UNI2-X-X ND-362442-MG-UNI2-X-X ND-362454-MG-UNI2-X-X ND-403264-MG-UNI4-X-X Strong strut bracket supports interrupter switches in either single (vertical or horizontal) or three phase vertical mount applications. Adjustable brackets in the ND-403264-MG-UNI4-X-X gives instant bracket adaptability to Elastimold or G&W bolt patterns. (Brackets do not include interrupter mounting hardware) Cabinet extensions are available in 18 or 36 heights for more cable bending radius. ND-683054-MG-UNI4-X-X Strong strut bracket supports three phase interrupter switches in vertical mount applications. Strut bracket system has 4 vertically adjustable horizontal brackets that accommodate a variety of manufacturer s vacuum switch interrupter s bolt patterns. (Brackets do not include interrupter mounting hardware) Cabinet extensions are available in 18 or 36 heights for more cable bending radius. ND-683054-MG-UNI4-X-X ND-403264-MG-UNI4-X-X Page 28

Covers, Ground Sleeve Covers for Ground Sleeves Standard Covers Rust free fiberglass construction and stainless steel hardware. The exterior is applied with a Munsell green gel-coat (not applicable to the GSC-37-43-MG cover), which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack. The standard cover is fabricated of one layer of 1/2 plywood encapsulated in fiberglass, using fireretardant resin and chopped glass and 18 ounce woven roving reinforcement. The word ELECTRIC can be printed on the cover for an additional charge. Covers are available for all box pads and ground sleeves. Four brass penta-head recesses are installed for securing the cover to the box pad. Covers come with four 3/8 x 1 1/2 stainless steel penta-head bolts. For larger sized covers, two layers of 1/2 plywood are standard, as are six to eight penta-head recesses and bolts. For retrofitting to box pads or ground sleeves that were not furnished with inserts, Nordic can provide stainless steel 3/8 and 1/2 floating nut inserts for installing the cover. GSC-37-43-MG UV stabilizers are contained in the resin to provide protection from ultraviolet light attack. The top of the cover is a textured non-skid diamond tread surface, which provides a safe operating platform in all types of weather. The GSC-37-43 covers are produced by a process known as cold pressed molding. Molded-in penta-head cups in the cover match the CBP s & GS-37-43 Series insert patterns for installation, bolting hardware included with each cover. Standard Cover GSC-75-72-MG GSC-37-43-MG Cover The word WARNING ELECTRIC is imprinted on every GSC-37-43 cover. Four brass penta-head recesses are installed for securing the cover to the box pad. For larger covers, six to eight penta-head recesses and bolts are installed. Page 29

Extenders and Adapters Extenders and Adapters Extenders Have a damaged box pad or a change in grade level? Ground sleeve extenders work great where you can shut off the power, excavate around the damaged sleeve, and install a ground sleeve extender over it. If the grade line has come up over the years, these units extend the ground sleeve up another 4 above grade The GSE-4A-MG-22x24 and GSE-4F-MG-26x30 go over box pads with a 37 x 43 top surface. Covers up a damaged box pad and raises it up 4 at the same time. Adapters GSA-37-43-MG-21x10 The GSA-37-43-MG-21x10 adapter is designed to fit on the GSLBJ-37-43-32C-CE-2-MG-22x24. This unit also accommodates the ND-301830 in either a single phase cabinet or tap pedestal. Because of its smaller top opening this adapter also accommodates single phase metal sectionalizing cabinets. Adapters GSA-36-36-MG-25x10 The GSA-36-36-MG-25x10 provides an adapter for the GS-80-36-36-2O-MG-TS. With the adapter mounted to the box pad, the ND-301830-MG-102A-X-X can be mounted to the adapter. The ND-301830-MG-102A-X-X can be used as a single phase sectionalizing cabinet. The ND-301830-MG-102A-X-X can also be used as a secondary tap pedestal called the ND-301830-MG-X-L750350P-X. Other metal single phase sectionalizing cabinets can be mounted to the GSA-36-36-MG-25x10. Replacement Ground Sleeve/Transformer Pads RGS-30-18-18-MG-21x10, RGS-61-18-18-MG-55x10, RGS-37-43- 10-MG-24x30, and RTP-42.5-45.5-7-MG-22x24. These replacement ground sleeves can be installed directly over rusted metal ground sleeves or after removal of the damaged sleeves. Front partition is removable for electrical cables to slide through during installation without disconnecting the power. The two-piece units are joined by driving 3/8 stainless steel bolts into the floating nut assemblies on the sides and flange of the sleeve. GSE-4A-MG-22x24 GS-37-43-32C-CE-2-MG- 22x24 with GSE-4A-MG-22x24 GSA-37-43-MG-21x10 GSLBJ-37-43-32C-CE- 2-MG-22x24 with the GSA-37-43-MG-21x10 mounted to it. GSA-36-36-MG-25x10 GS-80-36-36-2O-MG-TS with GSA-36-36-MG-25x10 mounted to it on the right side RGS-30-18-18-MG-21x10 GS-37-43-32C-CE-2-MG- 22x24 GSE-4F-MG-26x30 GSLBJ-37-43-32C-CE-2- MG-22x24 GSLBJ-37-43-32C-CE- 2-MG-22x24 with the GSA- 37-43-MG-21x10 and the ND-301830-MG-102A-X-X mounted to it GS-80-36-36-2O-MG-TS GS-80-36-36-2O-MG-TS with GSA-36-36-MG-25x10 & ND-301830-MG-102A-X-X. RGS-61-18-18-MG-55x10 RGS-37-43-10-MG-24x30 RTP-42.5-45.5-7-MG-22x24 Page 30

Flexi-Flags, Curb, and Cabinet Markers Hydrant Flexi-Flags, Curb Markers, and Cabinet Markers Wound galvanized spring steel is a tough material for all types of weather. The one-piece staff, coil spring or looped end is 53 or 72 tall. The HDPE flag provides approximately 20 square inches of surface area. Economical, easy to install, lasts for years. FF-1L and FF-2L Looped Hydrant Flexi-Flags Flag has a looped end. Simply remove the hydrant s housing cover and install the flag s loop over the threaded coupling, reinstall the cover with the flag. FF-1L - 53 High FF-2L - 72 High FF-1L installed FF-1 and FF-2 Hydrant Flexi-Flags The Flexi-Flag is field tested with staff, bracket, and spring made of wound galvanized spring steel, topped with an orange HDPE flag. FF-1-53 Hydrant Marker FF-2-72 Hydrant Marker CM-1 and CM-2 Curb Marker Flexi-Flags The Flexi-Flag is field tested with staff, bracket, and spring made of wound galvanized spring steel, topped with an orange HDPE flag. Snow removal personnel also benefit from seeing the brightly colored flag and avoid hitting a hydrant or curb with their snowplows. CM-1-53 Curb Marker CM-2-72 Curb Marker FF-1 installed FF-1C and FF-2C Cabinet Marker Flexi-Flags The Flexi-Flag is field tested with staff, bracket, and spring made of wound galvanized spring steel, topped with an orange HDPE flag. The Nordic Cabinet Marker helps to identify the location of cabinets and pedestals hidden by snow, brush, weed growth, or in crop fields. FF-1C - 53 Cabinet Marker FF-2C - 72 Cabinet Marker CM-1 installed FF-1C installed Page 31

Ground Sleeves for Single & Three Phase Enclosures Ground Sleeves, 1 & 3 Phase Sectionalizing CGS-30-18-18-MG-21x10 GS-30-18-30-MG-21x10 GS-61-18-18M-MG-55x10 Installed GS-61-18-18M-MG-55x10 Rust free and very little maintenance is required. CGS (compression ground sleeve) is manufactured of SMC (Sheet Molding Compound). SMC is a thermosetting compound which is pre-mixed with pigments that are molded into the fiberglass and cannot peel. Fire retardant and UV additives are permanently molded in throughout the laminate. GS units are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using 18 ounce woven roving glass reinforcement for a 1/4 nominal fiberglass thickness for great strength. M-Medium weight units have 3/16 nominal fiberglass thickness. Units can be pre-drilled to accommodate sectionalizing cabinets. Munsell green gel-coat is used for superior weather-ability. Labor saver; most units can be easily lifted by one person and installed the same day. Single and Three Phase Ground Sleeves CGS-30-18-18-MG-21x10 GS-31-19-18M-MG-22x13.5 GS-49-15-18M-MG-40.5x10.5 GS-67-23-30-MG-57x18 GS-10-12-18-MG-6x8 GS-31-23-18M-MG-22x18 GS-49-15-30-MG-40x10 GS-67-24-24M-MG-60x14 GS-18-18-18M-MG-9x9 GS-31-23-30-MG-22x17.5 GS-49-18-18M-MG-38x10.5 GS-70-18-18-MG-64x12.5 GS-19-10-18M-MG-15x6 GS-32-12-24-MG-24x4 GS-49-23-18M-MG-39.5x17 GS-71-25-24-MG-61.5x12.5 GS-24-22-18M-MG-17x16 GS-32-16-18M-MG-24x9 GS-49-23-30-MG-40x17.5 GS-72-25-48-MG-63x17 GS-24-22-30-MG-16x17.5 GS-32-16-30-MG-26x12 GS-61-15-18M-MG-53x11 GS-78-20-18-MG-72x14 GS-24-24-30-MG-16x16 GS-34-25-24-MG-26x17 GS-61-15-30-MG-52x10 GS-78-24-36-MG-70x16 GS-25-15-18M-MG-16x10 GS-35-20-18M-MG-25x11.5 GS-61-18-18M-MG-55x10 GS-85-23-18-MG-75x17 GS-25-19-18M-MG-19x13 GS-35-35-30-MG-27x27 GS-61-18-26-MG-55x10 GS-85-23-30-MG-73x16 GS-26-15-18M-MG-19x8 GS-36-24-24-MG-31x19 GS-61-18-30-MG-54x11 GS-96-27-30-MG-89.5x21 GS-26-18-18M-MG-17x9 GS-36-26-18M-MG-30x20 GS-61-20-18M-MG-55x10 GS-27-20-18M-MG-17.5x11.5 GS-37-23-18M-MG-28x18 GS-61-37-15-MG-52x32 GS-27-20-26-MG-18x12 GS-37-23-30-MG-27.5x17 GS-64-18-18M-MG-56.5x10.5 GS-30-18-24-MG-20x9 GS-38-20-18M-MG-30x12 GS-64-18-30-MG-56x13 GS-30-18-30-MG-21x10 GS-44-18-18M-MG-37x9.5 GS-64-20-18M-MG-57.5x12.5 GS-30-20-18M-MG-21x10 GS-44-26-24-MG-37x20 GS-64-20-30-MG-55x10 GS-30-20-30-MG-23.5x13 GS-44-44-18M-MG-32x32 GS-65-20-18M-MG-58x12 GS-31-10-36M-MG-27x6 GS-44-44-36-MG-34x34 GS-67-23-18M-MG-58x16.5 Page 32

Ground Sleeves, Traffi c ORDIC FIBERGLASS, INC. Ground Sleeves for Traffic Equipment GST-24-22-18-GR-17x16 GST-30-18-24-GR-24x13 GST-90-60-5-MG-20x10.5 These ground sleeves are produced of fire retardant resin and a combination of chopped glass spray-up and hand lay-up using 18 oz. woven roving glass reinforcement. The exterior is applied with a Mist Gray (Concrete Color) gel-coat, which contains UV stabilizer for superior weatherability. Stainless Steel floating nut inserts can be installed to match traffic control bolting patterns for an additional cost. The GST-90-48-5-MG-20x10.5 and GST-90-60-5 each feature a large walking surface for workers to step on and get out of the dewy grass or mud. Other gel-coat colors available. Please see our Cabinet Cross Reference Chart below. Common traffic signal cabinets are listed with the Nordic ground sleeve that will accommodate it. Cabinet Cross Reference Chart Cabinet Type W D Nordic Product 330 22 18 GST-24-22-18-GR-17x16 332 24 30 GST-36-24-24-GR-22x9 334 24 30 GST-36-24-24-GR-22x9 337 20 17 GST-24-22-18-GR-17x16 345 24 30 GST-36-24-24-GR-22x9 333SD 44 29 GST-50-30-20-GR-28x22 336A 24 20, 22 GST-24-22-18-GR-17x16 336S 24 20, 22 GST-24-22-18-GR-17x16 G 25 16 GST-30-18-24-GR-24x13 M 30 17 GST-30-18-24-GR-24x13 M36 36 17 GST-36-24-24-GR-22x9 P38 38 26 GST-44-26-24-GR-20x12 P44 44 26 GST-44-26-24-GR-20x12 P44 Super 59 26 GST-71-26-24-GR-55x12.5 R38 38 26 GST-44-26-24-GR-20x12 R44 44 26 GST-44-26-24-GR-20x12 Nordic Product L W H Opening GST-24-22-18-GR-17x16 24 22 18 17 x 16 GST-24-22-24-GR-17x16 24 22 24 17 x 16 GST-25-25-24-GR-12x12 25 25 24 12 x 12 GST-30-18-18-GR-24x13 30 18 18 24 x 13 GST-30-18-24-GR-24x13 30 18 24 24 x 13 GST-36-24-18-GR-22x9 36 24 18 22 x 9 GST-36-24-24-GR-22x9 36 24 24 22 x 9 GST-44-26-18-GR-20x12 44 26 18 20 x 12 GST-44-26-24-GR-20x12 44 26 24 20 x 12 GST-50-30-20-GR-28x22 50 30 20 28 x 22 GST-71-26-24-GR-55x12.5 71 26 24 55 x 12.5 GST-90-48-5-MG-20x10.5 90 48 5 20 x 10.5 GST-90-60-5-MG-20x10.5 90 60 5 20 x 10.5 Page 33

Hardware & Miscellaneous Accessories Hardware AB-2 Anchor bracket is designed to tie down transformers or switchgear. Enables various box pad insert patterns to accommodate more sizes of equipment. Manufactured of 3/8 thick carbon steel, hot-dipped galvanized. Comes with one 3/8 stainless steel bolt, one flat washer, and one lock washer. Measures 1 1/2 x 6 1/4. Bend in the bracket raises it 1/4 from the pad. Slot in the AB-2 bracket is 1/2 wide x 4 1/2 long. Can be factory installed on your box pad or shipped separately. Cable Entrance w/hardware Black plastic cover can be installed inside a secondary pedestal for a cable entrance cover. Maximum cable hole dimension is 2 OD. Includes mounting hardware. CAS-1 Hot-dipped galvanized steel cabinet anchors allow the customer to bolt a Nordic fiberglass sectionalizing cabinet to a cement pad. (CAS-1, 4 anchors) PH-1 (Penta-Head Wrench) Heavy duty chrome plated. Easy to use. Use it on transformers, switchgear, and other enclosures with penta-head bolt locking. Long lasting construction FN-Floating Nut Assemblies If you don t have access to the hex nut, this is the perfect way to tighten down almost anything. The square brass nut (FN-38=3/8 sq. nut, FN-12=1/2 sq. nut) is held by a stainless steel nut retainer and covered with a SST flat plate. Two #10 bolts with lock washers and #10 nuts can be installed almost anywhere. FN-38 FN-12 FN-38 & FN-12 Floating Nut Assemblies Nordic Repair Kits NRK-2 repair kit gives the customer the necessary materials to patch up a small fiberglass tear or puncture. NRK-3 Repair Kit covers up a damaged box pad corner. Includes fiberglass corner, silicone paintable clear caulk, and bolt kit. NRK-2 Repair Kit NRK-3 Page 34

Hardware Transformer Deferral Brackets TDB-2 can be installed in back corner of the GS-37-43-32A-CE-2 or the GS-37-43-32C-CE-2 box pads. The TDB-2-C15 can be installed in the back corner of the 15 high CBP A top opening units. TDB-2-C24 can be installed in the back corner of the 24 high CBP A top opening units. TDB-3 can be installed in back corner of the GS-37-43-32A-CE-2 or the GS-37-43-32C-CE-2 box pads. When the transformer is installed, the bracket and the box pad cover can be used in another temporary installation. Savings will be realized by delaying the investment in a transformer until it is needed. Also, savings will be made by not having to invest in or excavate a looping pedestal for a temporary looping arrangement. TDB-2 TDB-2-C15 TDB-2-C24 TDB-3 Penta-Head Bolts 304 Stainless steel penta-head bolts available in a variety of diameters and lengths. (Actual sizes not shown) PH-4 PH-6 PH-7 PH-8 Penta-Head Bolt (Stainless Steel) Dia. Thread Length Description PH-4 3/8 16 UNC 1.405 Washer and Point PH-6 1/2 13 UNC 1.50 No Washer or Point PH-7 3/8 16 UNC 1.75 Washer and Point PH-8 1/2 13 UNC 1.75 No Washer or Point Page 35

Hill Holders ORDIC FIBERGLASS, INC. Hill Holders Hill Holders Heavy duty 1/4 thick hill holders are produced of fire retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which contributes greatly to their strength. The exterior is applied with a Munsell green gel-coat which contains UV stabilizer in addition to pigments and polyester resin for superior weatherability. The exterior has a textured gel-coated finish and the interior has a smooth gel-coated finish. The NHH-32-46-52 and NHH-32-54-52- MG have two horizontal ribs on the back side for added strength. The 2 flange around the entire perimeter provides stability. NHH-16-46-52-MG NHH-32-46-52-MG NHH-20-54-52-MG NHH-32-54-52-MG B A C Hill Holder A Back Height B Back Width C Side Extensions NHH-16-46-52-MG 16 46.5 52 NHH-20-54-52-MG 20 54 52 NHH-32-46-52-MG 32.5 46.5 52.5 NHH-32-54-52-MG 32.5 54 52 Installed NHH-32-54-52-MG Page 36

Hand Holes, Plastic and Fiberglass Pedestals, Hand Holes PHH-161912-MG PHH2-161912-MG PHH-161918-MG PHH2-161918-MG PHH-212115-MG PHH2-212115-MG Plastic Hand Holes Plastic hand holes are made from copolymer polypropylene and designed for flush burial. The Munsell green pigment is blended throughout the material, which contains UV stabilizer for weather-ability. Units include a flat cover. ELECTRIC is imprinted on standard cover. GSHH-ground sleeve hand hole, HHC-hand hole cover, HHC2-hand hole PHH Lock PHH2 Lock cover with double lock, PHH-plastic hand hole, PHH2-plastic hand hole with double lock. Fiberglass Hand Holes These ground sleeves are produced of fire retardant resin and a combination of chopped glass spray-up and hand layup using 18 oz. woven roving glass reinforcement for a 1/4 fiberglass nominal thickness throughout the part. The exterior is covered with a Munsell Green gel-coat, which contains UV stabilizer for superior weather-ability. M-Medium Weight, 3/16 thick nominal fiberglass thickness. Nordic Products L x W x H Opening Description GSHH-25-16-16M-MG-21x12 25 x 16 x 16 21 x 12 Base with fl at cover GSHH-25-19-18-MG-19x13 25 x 19 x 18 19 x 13 Base with fl at cover GSHH-30-18-18-MG-24x12 30 x 18 x 18 24 x 12 Base with fl at cover GSHH-37-23-18-MG-31x17 37 x 23 x 18 31 x 17 Base with fl at cover HHC-1619-MG 16 x 19 N-A Flat cover only HHC-2121-MG 21 x 21 N-A Flat cover only HHC2-1619-MG 16 x 19 N-A Flat cover only, 2 Lock HHC2-2121-MG 21 x 21 N-A Flat cover only, 2 Lock PHH-161912-MG 16 x 19 x 12 12 x 16 Base with fl at cover PHH-212115-MG 21 x 21 x 15 18 x 18 Base with fl at cover PHH-161918-MG 16 x 19 x 18 12 x 16 Base with fl at cover PHH2-161912-MG 16 x 19 x 12 12 x 16 Base with fl at cover, 2 Lock PHH2-161918-MG 16 x 19 x 18 12 x 16 Base with fl at cover, 2 Lock PHH2-212115-MG 21 x 21 x 15 18 x 18 Base with fl at cover, 2 Lock GSHH-25-16-16M-MG-21x12 HHC-1619-MG HHC2-1619-MG HHC2-2121-MG HHC-2121-MG Page 37

Hand Holes, Below Grade Secondary Pedestals P-65-LID-MG P-60-MG P60MG (Inner & Outer Bell w/lid) P-63-MG (Inner Bell w/lid) P65MG P-65-MG (Outer Bell w/lid) P-60-Outer Bell P-60 Series The P-60 and P-65 pedestals are produced of compression-molded fiberglass. The green pigment is permanently molded into the fiberglass and cannot peel. Will not rust or corrode and resists ultraviolet attack. The word Electric Service is embossed on the lid s top. Units are 15 high, 14 diameter. P-60 employs the air bell principle for maintaining watertight compartment for cable splices. Continuous submersion tests have shown that the P-60, under six feet of water, allows only 2.3 inches of water to rise in the enclosure. A single lock on the P-60/65 reduces service and inspection time. The P-60 pedestal provides safe, enduring bell type housing for splices in underground cables. The P-60 is composed of two close-fitting pieces, the P-63 and outer shell. The unit is light enough for one person to complete the installation job in one trip to the site. P-60 can be flush-mounted at ground surface, partially or fully buried, or surface-mounted. P-65 is a pedestal with a lid and outer sleeve. P-63-MG (Cover and inner bell replacement for P-60-MG, both cover and inner bell are one piece) Pedestals Dimension Height Locking System P-60-MG, inner & outer bell with lid 14 Dia. 16.5 w/lid Tamper Proof Single Lock P-63-MG, inner bell with lid 14 Dia. 15 P-65-MG, outer bell with lid 14 Dia. 16.5 w/lid Page 38

Pedestals, Joint Trench ORDIC FIBERGLASS, INC. Pedestals, Joint Trench JTP-150-2-MG Joint Trench Pedestals JTP-190-1-MG Joint trench pedestals provide pedestals for secondary wiring, telephone, TV cable, and fiber optics together to one service area. These pedestals are combinations of the PRMC and P-50 Series pedestals. Various configurations are available. The attractive exterior and orderly arrangement of these pedestals will be greatly appreciated by homeowners. A variety of combinations are available to suit each application. The communications and cable television pedestals are secured to the electric pedestal with a fiberglass channel. The flange around the bottom perimeter of the base of the electric pedestal or stake provides excellent stability. JTPR-55-2 Joint Trench Pedestal Electrical Pedestal Cable or Communications Pedestal Qty (s) Transformer Pad Overall Height with Pedestal Standard Stake Optional Stakes JTP-150-1-MG PRMC-150 1-PR-50 None 30 None None JTP-150-2-MG PRMC-150 2-PR-50 s None 30 None None JTP-190-1-MG PRMC-190 1-PR-50 None 36 None None JTP-190-2-MG PRMC-190 2-PR-50 s None 36 None None JTPR-55-2-MG PR-55 1-PR-55 None 42 P-52 Yes Page 39

Pedestals, Looping ORDIC FIBERGLASS, INC. Looping Pedestals Looping Pedestals Rigid fiberglass construction using fire retardant resin and a combination of chopped glass spray-up and hand layup using woven roving for high strength. The exterior is with a UV stabilized Munsell green gel-coat for superior weather-ability and protection from ultraviolet light. Non-conductive and non-corrosive. LP-77-MG Designed for looping 15kV primary cable at points where future plans call for installation of additional equipment. Dimensions are 30 long x 8 deep x 30 high with a 5 flange around the bottom perimeter for excellent stability. LP-88-MG Designed for looping 25kV primary cable at points where future plans call for installation of additional equipment. Dimensions are 53 long x 23 deep x 47 high with a 5 flange around the bottom perimeter for excellent stability. LP-77-MG LP-88-MG Page 40

Pedestals, Meter ORDIC FIBERGLASS, INC. Meter Pedestals, Plastic MPP-141480-MG-X Rust free materials and stainless steel hardware. Linear Low Density Polyethylene Material is UV stabilized (Munsell Green Color). Trailer Parks, RV Campgrounds, and townhouses now have a plastic pedestal that can accommodate up to three meters or other pieces of equipment. Easy to drill through the plastic pedestal for quick meter installations. Install up to 3 Meters or other equipment. 14 x 14 x 80 tall with a 14 x 38 meter mounting surface on 3 sides. Meters not included. Service entrance door is made of a high density polyethylene material with a smooth finish. Includes a stainless steel penta-head bolt for locking (pad-lockable). Large 11 x 31 Front Opening. Make it a secondary pedestal by ordering 3 lay-in 6 port 350 MCM connectors installed inside. (MPP-141480-MG-L6350) Abundant access inside the pedestal. Lightweight, only 35 lbs. The corrugated base provides strength against sidewall ground pressures. The bottom of the base is flanged to prevent twisting when buried. Recommended burial depth 30. MPP-141480-MG-X MG Large service entrance door (11 x 31 ) is secured with a stainless steel penta-head bolt fastened to an encased brass nut on the interior frame. A stainless steel cup goes around the penta-head bolt for added security. The cup has a hole in it for pad-locking. MPP-141480-MG-L6350 Page 41

Meter Pedestals, Fiberglass MP/R-85-MG Rust free SMC and stainless steel hardware. This series is manufactured of compression-molded fiberglass (SMC). Fire retardant and UV additives are permanently molded in throughout the laminate. 88 tall pedestal will accommodate most surface-type meter mounts and service entrance equipment. 64 above grade allows for easy meter reading. Pigment is permanently molded into the fiberglass and the fiberglass does not peel, providing a maintenance free pedestal for many years. Fiberglass pedestals resist fertilizers, salt air, and ultraviolet attack. The back of the pedestal in removable for convenient cable training. Standard color is munsell green. Stakes are available for added stability when installed. Recessed penta-head locking is an option. MP-85 or MPR-85 (does not include meter, enclosure or conduit.) MPR-85-MG front side or fl at side is the surface area for mounting a meter to. Recommended burial depth 24. MP-85-MG (Hasp Lock) MPR-85-MG (Hasp & Penta-Head Lock) MP-85-MG (Hasp Lock) MPR-85-MG (Hasp & Penta-Head Lock) Nordic Meter Pedestal Dimension Height Above Ground Below Ground Locking System MPP-141480-MG 14 x 14 80 50 30 Penta-Head Bolt MPP-141480-MG-L6350 14 x 14 80 50 30 Penta-Head Bolt MP-85-MG 8 x 8 88 64 24 Hasp MPR-85-MG 8 x 8 88 64 24 Hasp and Penta-Head Page 42

Pedestals, Secondary ORDIC FIBERGLASS, INC. Pedestals, Plastic PSP-151530-MG-L6350 or PSP-151530-MG-L6600 Rust free materials and stainless steel hardware. Copolymer polypropylene pedestals are manufactured by an injection molding process with UV stabilized material. Polypropylene pedestals resist fertilizers, salt air, and ultraviolet attack. The green pigment is permanently molded into the copolymer polypropylene and can-not peel or rust. WARNING, ELECTRIC, is molded into the pedestal top for easy identification. cover has room for labels in the front. The top is secured to the base by a flange molded into the rear of the pedestal top and a penta-head bolt and hasp on the front. Accommodates three 6 port 350MCM or 600MCM connectors. Clear plastic covers included when connectors are ordered. Optional cable entrance cover available. All locking hardware is stainless steel. PSPF Series & PSPS Series Rust free materials and stainless steel hardware. PSP-151530-MG-CE Linear low density polyethylene material is UV stabilized. ELECTRIC is molded into the pedestal top for easy identification. There is an 8 x 10 label area molded in. Accommodates three or four 6 port 350 or 500 MCM connectors. Clear plastic covers included when connectors are ordered. All locking hardware is stainless steel. Suggested burial depth up to the molded in GROUND LINE. Molded step design resists deflection when buried. Optional cable entrance cover available. PSPF-101538-MG-CE PSPF Series has a flared bottom design allows for ample cable training, increased stability in a variety of soil conditions, and pedestal stacking. PSP-151530-MG-L6350 PSP-151530-MG-L6600 PSPF-101538-MG-L6350 PSPS-101544-MG-X Base Suggested Pedestals Height Lid Height Burial Connectors PSP-151530-MG-L6350 30 15 x 15 x 15 15 12 3 Lay-in, 6 port, 350MCM PSP-151530-MG-L6600 30 15 x 15 x 15 15 12 3 Lay-in, 6 port, 600MCM PSPF-101538-MG-X 38 10 x 15 x 17 35.5 16 None PSPF-101538-MG-L6350 38 10 x 15 x 17 35.5 16 3 Lay-in, 6 port, 350MCM PSPF-101538-MG-4L6350 38 10 x 15 x 17 35.5 16 4 Lay-in, 6 port, 350MCM PSPF-101538-MG-6500 38 10 x 15 x 17 35.5 16 3, 6 port, 500MCM PSPF-101538-MG-46500 38 10 x 15 x 17 35.5 16 4, 6 port, 500MCM PSPS-101544-MG-X 44 10 x 15 x 22 35.5 16 X-None, however, available with connectors like the PSPF Series Page 43 11/13

Pedestals, PSP Series Rust free materials and stainless steel hardware. Copolymer polypropylene pedestals are manufactured by an injection molding process with UV stabilized material. Polypropylene pedestals resist fertilizers, salt air, and ultraviolet attack. The green pigment is permanently molded into the copolymer polypropylene and can-not peel or rust. WARNING, ELECTRIC, is molded into the pedestal top for easy identification. cover has room for labels in the front. The top is secured to the base by a flange molded into the rear of the pedestal top and a penta-head bolt and hasp on the front. Optional cable entrance cover available. Ribs and steps are molded into the pedestal for rigidity. This design resists deflection in a buried position and ensures the base and lid a unified connection after servicing. Suggested Pedestals Lock Height Base Height Burial PSP-151530-MG Horizontal 30 15 12 PSP-91330-MG Horizontal 30 12 9 PSP-91336-MG Horizontal 36 18 15 PSPB-161912/18-MG Base Only 12-18 PSPB-212115-MG Base Only 15 PSPT-151515-MG Only 15 PSPT-91318-MG Only 18 Pedestals convertible to Hand Holes PSPX-151530-MG Vertical 30 15 12 PSPX2-151530-MG Double 30 15 12 PSPXB-212115-MG Base Only 15 PSPXT-151515-MG Only 15 PSPX-91330/36-MG Vertical 30-36 12-18 9-15 PSPX2-91330/36-MG Double 30-36 12-18 9-15 PSPXB-161912-18-MG Base Only 12-18 PSPXT-91318-MG Only 18 PSPX domed pedestals are convertible to hand holes. The vertical locking mechanism bolts to the base fl ange. The domed cover can be removed and a fl at cover (HHC-2121 or HHC-1619), can be attached to the base. HHC2-2121 and HHC2-1619 can be used as covers for the PSPX2 pedestals, PSPXTplastic secondary pedestal convertible top, X-convertible, T-, PSPXB-plastic secondary pedestal convertible base, B-Base, PSPX-plastic secondary pedestal convertible to a hand hole. PSP-151530-MG PSP-91330-MG PSPX-91330-MG PSPX2-91330-MG PSP-91336-MG PSP-91330-MG-CE PSP Lock PSPX Lock PSPX2 Lock PSPX-151530-MG PSPX-91336-MG PSPX2-151530-MG PSPX2-91336-MG Cable Entrance Cover: Black plastic cover can be installed inside a secondary pedestal for a cable entrance cover. Maximum cable hole dimension is 2 OD. Includes mounting hardware. PSP Lock: Horizontal lock; pentahead bolt enters a plastic receiver in base to hold in place. Hasp is riveted to base. Hasp tab has hole for pad locking lid to base. PSPX Lock: Vertical single locking mechanism bolts to the base fl ange. PSPX2 Lock: Vertical double locking with a bit on the lid and base to allow pad-lock shaft to slide through for padlocking. 11/13 Page 44

Pedestals, P-50 Series Rust free SMC and stainless steel hardware. The P-50 and P-55 Series are manufactured of compression molded fiberglass (SMC). Fire retardant and UV additives are permanently molded in throughout the laminate. Pigment is permanently molded into the fiberglass and the fiberglass does not peel, providing a maintenance free pedestal for many years. Fiberglass pedestals resist fertilizers, salt air, and ultraviolet attack. Available in Munsell Green color. Two sizes of Nordic pedestals, for installation with anchoring devices, are available for above ground housing of cable splices. The top section is removable for easy access to cables. Stakes are available for added stability when installed. Recessed penta-head locking is an option. P-50-MG P-50-P-MG PR-50-MG P-55-MG P-55-P-MG PR-55-MG Installed PR-50 Installed PR-55 Hasp Lock Penta Head Lock Hasp & Penta Head Lock Pedestal Dimension Height Above Ground Below Ground Locking System P-50-MG 8 x 8 44 24 20 Hasp P-50-P-MG 8 x 8 44 24 20 Penta-Head PR-50-MG 8 x 8 44 24 20 Hasp & Penta-Head P-55-MG 8 x 8 44 34 10 Hasp P-55-P-MG 8 x 8 44 34 10 Penta-Head PR-55-MG 8 x 8 44 34 10 Hasp & Penta-Head PR-50-P-51-MG P-50-MG-P-52 P-50-MG-P-53 Stakes Description Dimension P-51 Fiberglass Anchor 19 x 2 x 2 P-52 Galvanized Steel Stake 48 Long P-53 Galvanized Steel Stake 60 Long P-54 Galvanized Steel Stake 72 Long Page 45 11/13

Pedestals, PRMC Series Rust free SMC and stainless steel hardware. PRMC series is manufactured of compression-molded fiberglass (SMC). Fire retardant and UV additives are permanently molded in throughout the laminate. Pigment is permanently molded into the fiberglass and the fiberglass does not peel, providing a maintenance free pedestal for many years. Fiberglass pedestals resist fertilizers, salt air, and ultraviolet attack. Available in Munsell Green color. Stainless steel and aluminum hardware provide long term protection against rust. ELECTRIC is molded in raised lettering on the top lid. A 3 flange around the perimeter provides stability when buried. Optional cable entrance cover available. P-109 locking assembly for safety. PRMC-150-MG Cable Entrance Cover: PRMC-160-MG PRMC-170-MG PRMC-190-MG Black plastic cover can be installed inside a secondary pedestal for a cable entrance cover. Maximum cable hole dimension is 2 OD. Includes mounting hardware. PRMC-150-MG-CE Pedestal Height Cover Dimensions Lid Height Base Height Above Ground Below Ground Locking System PRMC-150-MG 30 9 x 14 x 18 18 12 21 9 P-109 PRMC-160-MG 24 9 x 14 x 12 12 12 15 9 P-109 PRMC-170-MG 30 9 x 14 x 12 12 18 15 15 P-109 PRMC-190-MG 36 9 x 14 x 18 18 18 21 15 P-109 11/13 Page 46

Pedestals, Tap Pedestals, Tap ND-301830-MG-X-L750350P-X Rust free fiberglass construction and stainless steel hardware. This secondary pedestal accommodates up to three connectors with each connector accommodating one large 750MCM feeder cable, six 350MCM secondary taps, and two street lighting taps. ND-301830-MG-X-L750350P-X has a removable lid for easy access for hooking up secondary wires to the connectors. The 750MCM feeder cable accommodates a wire range of 750MCM maximum to 1Ø minimum. The 350MCM secondary tap accommodates a wire range of 350MCM maximum to No. 10 wire minimum. No part of the connector comes in contact with the shell of the pedestal for safety. The connector provided has a lay in type set screw assembly that provides for easy cable connection in the field. Electrical utilities will be able to use less elbows, less primary cable, and reduce labor associated with installing elbows onto the primary cable in the transformer. Benefits can also be realized by reducing the number of single phase transformers to provide power to apartment complexes, retirement communities and other installations of a similar nature. The ND-301830-MG-X-L750350P-X does not include the ground sleeve. Available ground sleeves include: CGS-30-18-18-MG-21x10 GS-30-18-24-MG-20x9 GS-30-18-30-MG-21x10 Width Cabinet Height Recommended Burial Tap Pedestal ND-301830-MG-X-L750350P-X 30 19.5 31 GS Required Page 47

Pedestals, Tap ND-3624 Series Rust free fiberglass construction and stainless steel hardware. Convex base shape and step design resist sidewall deflection when installed. Pedestals accommodate up to 3 or 4 connectors. Each fiberglass angle accommodates one heavy duty 10 or 12 port 750MCM connector each with a rubber insulating boot. Conductor wire range is 750MCM down to 1/0. No part of the connector comes in contact with the shell of the pedestal for safety. Connectors are manufactured from high strength 6061-T6 aluminum alloy to provide premium electrical and mechanical performance. Suitable for use with either copper or aluminum conductors. Clear Plated, each covered with a rubber insulating boot Rated for 600 Volts, connector meets or exceeds ANSI C119.4 Class A specifications. 3 or 4 fiberglass L-brackets are bolted to a fiberglass U-channel mounted in the cabinet s interior for a rigid mounting assembly. Connectors are evenly distributed approximately six inches between each other for room to work safely. The ND-362436 Series pedestals can be direct buried or pad mounted. The pedestal s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the wires, and place it in the excavated area. Rotational lid rotates on pivot bolts creating a lower center of gravity that reduces the force required to open the pedestal. Save by buying fewer transformers, elbows, primary cable and labor. ND-362436-MG-3HDB-10750-X Cabinet Base Base Max. Burial Tap Pedestal Width Height Width ND-362436-MG-3HDB-X-X 36.5 36.5 55 42 Finish grade ND-362436-MG-4HDB-X-X 36.5 36.5 55 42 approximately 6 below ND-362442-MG-3HDB-X-X 36.5 42.5 59 46 locking ND-362442-MG-4HDB-X-X 36.5 42.5 59 46 systerm. ND-362454-MG-3HDB-X-X 36.5 55 64.5 51.5 ND-362454-MG-4HDB-X-X 36.5 55 64.5 51.5 ND-362436-MG-4HDB-12750-X Page 48

Pedestals, Tap ND-403264-MG-4HDB-24750-X Rust free fiberglass construction and stainless steel hardware. Convex base shape and step design resist sidewall deflection when installed. Each of the 4 fiberglass arms accommodates one heavy duty 24 port 750MCM connector insulated by a rubber boot. Conductor wire range is 750MCM down to 1/0. Connectors are manufactured from high strength 6061-T6 aluminum alloy to provide premium electrical and mechanical performance. Suitable for use with either copper or aluminum conductors. Clear Plated, each covered with a rubber insulating boot Rated for 600 Volts Connector meets or exceeds ANSI C119.4 Class A specifications. No part of the connector comes in contact with the shell of the pedestal for safety. Adjustable sturdy strut system can be moved vertically for a safe working position. Connector brackets can be moved horizontally to where you want them. Fiberglass arms provide high dielectric insulating properties. The ND-403264 pedestals can be direct buried or pad-mounted. The pedestal s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the wires, and place it in the excavated area. Rotational lid rotates on pivot bolts creating a lower center of gravity that reduces the force required to open the pedestal. Save by buying fewer transformers, elbows, primary cable and labor. Need more cable bending radius? Ask for an 18 (ND-403264-MG-18EXT) or 36 high extension (ND-403264-MG-36EXT) that can bolt to the bottom of the pedestal. Tap Pedestal Width Cabinet Height Base Width Base Max. Burial ND-403264-MG-4HDB-24750-X 39.5 63.5 64.5 51.5 18 ND-403264-MG-4HDB-X-X 39.5 63.5 64.5 51.5 18 ND-403264-MG-4HDB-24750-X ND-403264-MG-18EXT Page 49

This Page is intended to be blank Page 50

PRODUCT CATALOG 2013 Page 51