Instructions for use, installation, and connection Gas Built in Hob RB3311SGBS RB3312SGBS RB3311DGBS RB3311MGBS RB3311NGBS RB6313SGBST RB6323SGBST RB6314SGBS RB6313DGBST RB6313MGBST RB7312SGBS RB7313SGBST RB7323SGBST RB7314SGBS RB7315SGBS RB7313DGBST RB7312MGBS RB7313MGBST RB7312NGBS RB9312SGBS RB9313SGBST RB9314SGBS RB9315SGBS RB9312DGBS RB9213DGBST RB9314DGBS RB9315DGBS RB9312MGBS RB9313MGBST RB9312NGBS RB9313NGBSU 1
Contents 1. Important Warnings... 3 2. Safety Instructions... 4 3. Line up... 6 4. Components and Parts name... 7 5. Installation... 8 6. Operating Instructions... 12 7. Maintenance... 13 8. Trouble Shootings... 17 9. Technical Specifications... 18 Thankyou very much for purchasing Rinnai Gas Built in Hob. More than 90 years of history of introducing high qualified Japandesigned appliances throughout the world. Every time you use Rinnai appliances, Rinnai believes you can feel comfort by its safety and quality. In order to maximize the performance and to maintain your Rinnai builtin hob in the best condition, please follow the instruction carefully. Please visit www.rinnai.com for further inquires 2
1. Important Warnings Before installing and using of Rinnai appliances, carefully read and follow the supplied instructions. The manufacturer is not responsible for any damages caused by incorrect installation and use. This instruction shall always be kept with the appliance for future reference and pass them on to possible new owners of the appliance. 1.1 General The appliance and its accessible parts become hot during use. Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. Never try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket. The appliance is not intended to be operated by means of an external timer or separate remote control system. Do not store items on the cooking surfaces. Do not use a steam cleaner to clean the appliance. 1.2 Children and vulnerable people WARNING! Risk of suffocation, injury or permanent disability. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are supervised by an adult or a person who is responsible for their safety. Never let children play with the appliance. Keep all packaging material out of the reach from children. Keep children and pets away from the appliance when it operates or when it cools down. Never let children clean and maintenance without supervision. 3
2. Safety Instructions 2.1 Installation WARNING! Only a qualified person must install this appliance. Remove all the packaging. Never install or use a damaged appliance. The minimum distance shall be kept from the other appliances and units as instructed. Always wear safety gloves and be careful when you move the appliances. Protect the bottom of the appliance from any steam and moisture. Preventing from the appliance to fall, never install the appliance adjacent to a door or under a window. Sufficient spaces are needs for air circulation when the appliance is installed above drawers. Gas connection All gas connections must be made by a qualified person. Confirm sufficient air circulation around the appliance. Always connect the appliance according to the latest installation regulations. 2.2 Use WARNING! Risk of burns. CAUTION: The use of a gas cooking appliance results in the production of heat, moisture and products of combustion in the room in which it is installed. Ensure that the kitchen is well ventilated especially when the appliance is in use : keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood). CAUTION : This appliances is for cooking purposes only. It must not be used for other purposes, for example room heating. This appliance is intended for use in household. Never change the specification of this appliance. Do not let the appliance stay unattended during operation. Ensure the cooking zone to off after cooking. WARNING! Risk of fire or explosion. Fats and oil when heated can release flammable vapors. Keep flames or heated objects away from fats and oils when you cook with them. The vapors of hot oil releases may cause spontaneous combustion. Used oil may cause fire at a lower temperature. Never place flammable products or items near or on the appliance. WARNING! Risk of damage to the appliance. Do not place and keep hot cookware on the control panel. Do not ignite the flames with empty cookware or without cookware. Be careful not to let objects or cookware fall on the appliance. The glass top plate can be damaged. Do not place aluminum foil on the appliance. Never use unstable cookware with the incorrect shape and diameter larger than the dimensions of the burners. Make sure the flame does not go out when you quickly turn the knob from the maximum to the minimum position. 4
Make sure cookware is centrally positioned on the pan supports and do not stick out over edges of the cooking surface. Only apply the accessories supplied by manufacturer. Never install a flame diffuser on the burner. 2.3 Care and Cleaning WARNING! Risk of damage to the appliance. Clean regularly the appliance to prevent the deterioration of the surface material. Do not use steam to clean the appliance. Never use the dishwasher to clean the burners in the dishwasher. Clean the appliance with a moist soft cloth, and only use neutral detergents. Never use abrasive products, abrasive cleaning pads, solvents or metal objects. CAUTION: In case of hotplate glass breakage: Shut immediately off all burners and any electrical heating element and isolate the appliance from the power supply. Do not touch the appliance surface, Do not use the appliance 2.4 Caution for the tempered glass Never use oversized cooking utensils or overload the cooking appliances. Do not remove the pan support and enclose the burner with a wok stand as this will concentrate and deflect the heat onto the gas hob. Do not place the builtin hob pan over the pan support side as it can cause tumbling. Use only a wok support supplied or recommended by the manufacture of the appliance. Do not place anything, e.g., flame tamer, asbestos mat between pan and support as serious damage to appliance may result. 2.5 Disposal WARNING! Risk of injury or suffocation. Please contact your near municipal authority for detailed information on the disposal of appliance. 5
3. Line up 30cm Models Top Plate Dimension ; 310 mm 520 mm CutOut Hole Dimension ; 268 mm 490 mm R0 mm ~ R50 mm RB3311NGBS RB3311MGBS RB3311DGBS RB3311SGBS RB3312SGBS Inner Flame Mega Double 60cm Models Top Plate Dimension ; 620 mm 520 mm CutOut Hole Dimension ; 560 mm 480 mm R0 mm ~ R50 mm RB6313MGBST RB6313DGBST RB6313SGBST RB6323SGBST Mega Double RB6314SGBS 75cm Models Top Plate Dimension ; 770 mm 520 mm CutOut Hole Dimension ; 725 mm 480 mm R0 mm ~ R50 mm RB7312NGBS Inner Flame RB7312MGBS RB7313MGBST RB7313DGBST Mega RB7313SGBST RB7323SGBST Mega Double RB7314SGBS RB7315SGBS RB7312SGBS 90cm Models Top Plate Dimension ; 880 mm 520 mm CutOut Hole Dimension ; 830 mm 470 mm R0 mm ~ R100 mm 6 RB9312NGBS RB9313NGBSU RB9312MGBS RB9313MGBST Inner Flame Inner Flame Mega Mega RB9312DGBS RB9313DGBST RB9314DGBS RB9315DGBS Double Double Double Double RB9312SGBS RB9313SGBST RB9314SGBS RB9315SGBS
4. Components and Parts name Rinnai Original Burner Series Inner Flame Series Mega Series Double Series Series Parts Names Pan Support H Drip Pan Burner Cover H Inner Flame Series Pan Support S Burner Cover S Drip Pan S Pan Support Mega Series Burner Head S Burner Head H Burner cover Drip Pan Drip Pan Seal Packing Burner S Top Burner HS Knob Casing Tempered Glass Top Plate Double Series Knob Casing Series Tempered Glass Top Plate Pan Support H Pan Support Center Pan Support S Pan Support H Burner Head Burner Head H Burner Body H Burner Head S Burner Body S Small Burner Cap Burner Body S Burner Cover S Burner Cap Burner Cap H Burner Body H Burner Cover H Knob Casing Tempered Glass Top Plate Knob Casing Tempered Glass Top Plate 7
5. Installation Kitchen worktop cutout dimensions Model Cut out hole dimension (mm) 30 cm RB3311SGBS RB3312SGBS RB3311DGBS RB3311MGBS RB3311NGBS 268 x 490 R0~R50 R0~R50 268 65 490 600 (MIN) 60 cm RB6313SGBST RB6323SGBST RB6314SGBS RB6313DGBST RB6313MGBST 560 x 480 R0~R50 R0~R50 560 65 480 600 (MIN) 75 cm RB7312SGBS RB7313SGBST RB7323SGBST RB7314SGBS RB7315SGBS RB7313DGBST RB7312MGBS RB7313MGBST RB7312NGBS 725 x 480 R0~R50 R0~R50 725 65 480 600 (MIN) 90 cm RB9312SGBS RB9313SGBST RB9314SGBS RB9315SGBS RB9312DGBS RB9213DGBST RB9314DGBS RB9315DGBS RB9312MGBS RB9313MGBST RB9312NGBS RB9313NGBSU 830 x 470 R0~R100 R0~R100 830 65 470 600 (MIN) 8
WARNING! * Install the builtin hob in a well ventilated room and keep it away from any combustible or flammable objects such as paper or oil. * Place the builtin hob on a stable and level surface. * If the builtin hob is to be installed close to combustible objects (such as wooden walls, wooden shelves), it should be installed at least 15 cm from the side walls. Even if the combustible material is protected by stainless steel sheet, a clearance of 15 cm must be maintained too. If the surrounding material is fireproof, 15 cm clearance is not required. The clearance between the appliance and above combustible shelves or the ceiling must be at least 100 cm. * (For Mega burner series only) If the oven is installed underneath of hob, it is mandatory to install the separator in between. The separator must be made out of incombustible material (eg. metal or plywood). 150 (min) 1000 (min) 150 (min) 150 (min) If the separator is placed underneath of the hob, its distance shall be recommended to be kept more than 150mm away from the surface of kitchen worktop. Please refer to below diagram. 150 Adjust screw position as bench cut out size. Confirm that four screws are secured firmly into the casing. Table Casing Screw 9
Set the battery properly as instructed. Model Ignition Battery Size RB3311SGBS C (1.5V 1) Battery holder location Front RB3312SGBS C (1.5V 1) 30 cm RB3311DGBS C (1.5V 1) RB3311MGBS C (1.5V 1) RB3311NGBS C (1.5V 1) C (1.5V 1) RB6313SGBST C (1.5V 1) Front Front 60 cm RB6323SGBST C (1.5V 1) RB6314SGBS D (1.5V 2) RB6313DGBST C (1.5V 1) RB6313MGBST C (1.5V 1) C (1.5V 1) D (1.5V 2) RB7312SGBS C (1.5V 1) RB7313SGBST C (1.5V 1) RB7323SGBST C (1.5V 1) Front Front RB7314SGBS D (1.5V 2) 75 cm RB7315SGBS D (1.5V 2) RB7313DGBST C (1.5V 1) RB7312MGBS C (1.5V 1) RB7313MGBST C (1.5V 1) RB7312NGBS C (1.5V 1) RB9312SGBS C (1.5V 1) RB9313SGBST C (1.5V 1) RB9314SGBS D (1.5V 2) C (1.5V 1) D (1.5V 2) RB9315SGBS D (1.5V 2) RB9312DGBS C (1.5V 1) Front Front 90 cm RB9213DGBST C (1.5V 1) RB9314DGBS D (1.5V 2) RB9315DGBS D (1.5V 2) RB9312MGBS C (1.5V 1) C (1.5V 1) D (1.5V 2) RB9313MGBST C (1.5V 1) RB9312NGBS C (1.5V 1) RB9313NGBSU C (1.5V 1) 10
Set the pan support properly as instructed. * Set pan support to top plate. Inner Flame Series H, S Mega Series H Burner S Burner Double Series H, S Series H, S H Burner S Burner H Burner S Burner Installation of Gas Hose Certified rubber hose for builtin hob must be applied. The rubber hose must no be bent during installation and must be at appropriate length (less than 2 m). During installation, make sure that the rubber hose must not touch the body and bottom part of the builtin hob. Set the securing ring over the rubber hose and connect to the gas inlet rear side of the builtin hob till the red marked line. Secure the position of rubber hose by tightening securing ring. The installation of gas hose must be performed by a qualified installer according to the relevant standards (For LP Gas). Red marked line Gas inlet Rubber hose Securing ring Important Once installation is complete, check the perfect seal of every pipe fitting, using a soapy solution, never a flame. 11
6. Operating Instructions Ignition 1. Press the control knob for about 3 mm and turn to the left (counter clockwise) to the (MAX) position. 2 In the event of the burner flames being accidentally extinguished, turn off the burner control and do not attempt to reignite the burner for at least 1 min. If the burner has not lit up after 15 seconds, stop operating the builtin hob and open the compartment door and/or wait for at least 1 minute before attempting to ignite the burner again. 3. The flame can be controlled between (MAX) and (MIN) position, please adjust the flame slowly. 4. Do not clean the top of the sensor with a hard brush, as it may damage the sensor. Max Position Min Position Flame Extinguishing 1. After the usage, turn the control knob right (clockwise) to the original position and the flame will be extinguished. 2. After extinguishing of the flame, do not touch the conductive parts of the builtin hob as they may remain at high temperature. 3. There might be a slight hissing sounds after the extinguishing of the flame. 4. If the builtin hob is not in use, turn off the main gas supply in order to avoid gas leakage or unnecessary accidents. How to Handle Safety Device 1. If the flame is extinguish during operation, the flame failure safety device will automatically cut off the gas within second. If you notice that the flame has been extinguished, please turn the knob to position and do not attempt reignite the burner at least 1 minute. 12
7. Maintenance How to Change Battery 1. If the battery ran out, open the cabinet door and change it correctly. The location of the battery is described in Page 10. Battery box is located at bottom of builtin hob. Open the cabinet door and change the battery. * Set battery correctly with care. How to set Drip Pan Inner Flame Series * Set Burner Cover properly as instructed. * Set drip pan into burner correctly, without gap. Burner Cover Gap Pin Drip Pan Mega Series * Set the drip pan properly as instructed. Drip Pan Pin Gap 13
* Set Burner Head H on Top Burner Body HS properly. The Pin of Burner Head H shall be located onto the on Top Burner Body HS. Set Burner Head S on the Top Burner Body HS properly. Pin Pin Burner Head H Burner Head S Top Burner Body HS Gap Gap Double Series H, S * Install Burner Body H to Burner Base H properly. The on Burner Body H shall be properly located onto the Pin of Burner Base H. * Install Burner Head H to Burner Body H properly. The on Burner Body H shall be properly located onto the Pin of Burner Head H. * Install Burner Head to Burner Body H properly. The on Burner Body H shall be properly located onto the Pin of Burner Head. Burner Body H Burner Head Burner Head H Pin Pin Pin Burner Body H Burner Base H 14
* Install Burner Body S to Burner Base S properly. The on Burner Base S shall be properly located onto the Guide Pin of Burner Body S. * Set Burner Head S on Burner Body S. Guide Pin Burner Body S Burner Head S Pin Burner Base S * Set Burner Head on Burner Body H properly without gap as below illustration. Gap Gap Burner Head Burner Body H Gap 15
Series H, S * Set burner Body H on burner base H. Be careful to align guide pin of burner body with slot of burner base. * Install Burner Cap H and Burner Cap properly onto Burner Body H. Guide Pin Burner Cap Burner Body H Burner Cap H Burner Base H * Install Burner Body S to Burner Base S properly. The on Burner Base S shall be properly located onto the Guide Pin of Burner Body S. * Set Small Burner Cap on Burner Body S. Burner Body S Guide Pin Small Burner Cap Burner Body S Burner Base S * Set burner cap on burner body properly without gap as below illustration. Burner Cap Gap Gap Burner Body Gap 16
8. Trouble Shootings FAULT CAUSE REMEDY 1. No Ignition Spark electrode is wet, especially in high humidity season. Dry the electrode with clean tissue or dry cloth. 2. Flame cannot be held. Incorrect turning of gas control knob. Push and turn the gas control knob anticlockwise until a click sound is heard. Hold for a few seconds until flame is ignited. 3. No main flame. Gas regulator has been turned off. Open gas regulator completely. 4. Yellow flame. Accumulated grease and dirt on the burner. Wash the burner in warm water with detergent. Leave it to dry, then place it back in the correct position. 5. Unstable flame. Incorrect location of burner head. Refit burner head into burner ring. 17
9. Technical Specifications Model Net Weight Overall Dimension Cut out hole size (mm) Ignition Battery Size Respective gas consumption (kw) Type of High Medium small all gas Gas Connecting Tube RB3311SGBS 6.8 310 x 520 x 130 3.7 3.7 30 cm RB3312SGBS 8.1 310 x 520 x 130 3.2 1.6 4.7 RB3311DGBS 7.8 310 x 520 x 136 268 x 490 R0~R50 C (1.5V 1) 4.2 4.2 RB3311MGBS 8.2 310 x 520 x 127 5.0 5.0 RB3311NGBS 7.1 310 x 520 x 112 3.5 3.5 RB6313SGBST 14.2 620 x 520 x 130 C (1.5V 1) 3.7 1.6 x 2 6.8 60 cm RB6323SGBST 14.6 620 x 520 x 130 C (1.5V 1) 3.7 3.2 1.6 8.2 560 x 480 RB6314SGBS 16.0 620 x 520 x 130 D (1.5V 2) 3.2 x 2 1.6 x 2 9.3 R0~R50 RB6313DGBST 15.4 620 x 520 x 136 C (1.5V 1) 4.2 1.5 x 2 7.2 RB6313MGBST 15.8 620 x 520 x 127 C (1.5V 1) 5.0 1.5 x 2 8.0 RB7312SGBS 16.4 770 x 520 x 130 C (1.5V 1) 3.7 x 2 7.2 RB7313SGBST 17.2 770 x 520 x 130 C (1.5V 1) 3.7 1.6 x 2 6.8 RB7323SGBST 17.4 770 x 520 x 130 C (1.5V 1) 3.7 3.4 1.6 8.5 75 cm RB7314SGBS 18.8 770 x 520 x 130 D (1.5V 2) 3.4 x 2 1.6 x 2 9.7 RB7315SGBS 20.0 770 x 520 x 130 725 x 480 R0~R50 D (1.5V 2) 3.4 x 2 1.6 x 3 11.0 RB7313DGBST 18.0 770 x 520 x 136 C (1.5V 1) 4.2 1.5 x 2 7.2 RB7312MGBS 18.9 770 x 520 x 127 C (1.5V 1) 5.0 x 2 9.9 L.P.G (30 mbar) ø 9.5 mm gas specific rubber hose RB7313MGBST 18.6 770 x 520 x 127 C (1.5V 1) 5.0 1.5 x 2 8.0 RB7312NGBS 16.9 770 x 520 x 112 C (1.5V 1) 3.5 x 2 6.8 RB9312SGBS 17.3 880 x 520 x 130 C (1.5V 1) 3.7 x 2 7.2 RB9313SGBST 17.7 880 x 520 x 130 C (1.5V 1) 3.7 x 2 1.6 8.7 RB9314SGBS 19.8 880 x 520 x 130 D (1.5V 2) 3.7 x 2 1.6 x 2 10.3 RB9315SGBS 21.0 880 x 520 x 130 D (1.5V 2) 3.7 x 2 1.6 x 3 11.5 RB9312DGBS 18.8 880 x 520 x 136 C (1.5V 1) 4.2 x 2 7.9 90 cm RB9213DGBST 20.1 880 x 520 x 136 830 x 470 C (1.5V 1) 4.2 x 2 1.5 9.4 RB9314DGBS 21.5 880 x 520 x 136 R0~R100 D (1.5V 2) 4.2 x 2 1.5 x 2 10.7 RB9315DGBS 22.8 880 x 520 x 136 D (1.5V 2) 4.2 x 2 1.5 x 3 12.2 RB9312MGBS 19.6 880 x 520 x 127 C (1.5V 1) 5.0 x 2 9.9 RB9313MGBST 20.6 880 x 520 x 127 C (1.5V 1) 5.0 4.2 1.5 10.4 RB9312NGBS 17.7 880 x 520 x 112 C (1.5V 1) 3.5 x 2 6.8 RB9313NGBSU 19.2 880 x 520 x 112 C (1.5V 1) 3.5 2.9 1.5 7.8 18
19
http://www.rinnai.com 20