510-0001 AND ON CITATION PERFORMANCE CALCULATOR (CPCalc) COPYRIGHT 2007 CESSNA AIRCRAFT COMPANY WICHITA, KANSAS, USA 11 APRIL 2007 U.S. S3-1
CITATION PERFORMANCE CALCULATOR (CPCalc) Use the Log of Effective Pages to determine the current status of this supplement. Pages affected by the current revision are indicated by an asterisk (*) preceding the page number. Supplement Status Date Original 11 April 2007 LOG OF EFFECTIVE PAGES Page Number Page Status Revision Number Configuration Code S3-1 thru S3-8 Original 0 S3-AA S3-2 U.S. Configuration S3-AA
SERVICE BULLETIN CONFIGURATION LIST The following is a list of Service Bulletins that are applicable to the operation of the airplane, and have been incorporated into this supplement. This list contains only those Service Bulletins that are currently active. Number Title Airplane Serial Effectivity Revision Incorporated Incorporated in Airplane Configuration S3-AA U.S. S3-3
AIRPLANE CONFIGURATION CODES The following is a list of airplane configuration codes which appear at the bottom of each page of this supplement to the basic FAA Approved Airplane Flight Manual. The codes indicate page effectivity by serial number. This list contains only the configurations which have been incorporated into this supplement. Configuration Code S3-AA Effectivity by Serial Number Airplanes 510-0001 thru -0004 Incorporating SL510-99-01 and Airplanes 510-0005 and On using the Citation Performance Calculator (CPCalc). S3-4 U.S. Configuration S3-AA
CITATION PERFORMANCE CALCULATOR (CPCALC) INTRODUCTION This supplement is part of, and must be placed in, the basic FAA Approved Airplane Flight Manual for Airplanes 510-0001 and On using performance information from the Citation Performance Calculator (CPCalc). The information contained herein supplements the information of the basic FAA Approved Airplane Flight Manual. For limitations, procedures and performance information not contained in this supplement, consult the basic FAA Approved Airplane Flight Manual. OPERATING LIMITATIONS GENERAL 1. The software version displayed on the main startup screen of the CPCalc must match the software version that corresponds with the applicable AFM revision as shown in the following table: OPERATIONAL APPROVALS The CPCalc provides FAA approved Section IV Takeoff and Landing performance information and provides Section VII Wet Takeoff and Landing performance information. 1. The CPCalc is approved for use as an alternative source to the takeoff and landing data presented in Section IV of the basic FAA Approved Airplane Flight Manual. 2. The CPCalc and AFM are each equally valid sources of performance data; however, the operator must use speed and distance data from only one of these sources. 3. Inputs with decimal values must be entered into CPCalc using the current decimal separator symbol selected in the Windows operating system regional control panel options. No other separator symbols are allowed as input values. OPERATING PROCEDURES The operating procedures are the same as the basic FAA Approved Flight Manual except as follows: EMERGENCY PROCEDURES No change. ABNORMAL PROCEDURES No change. NORMAL PROCEDURES No change. CPCalc Software Version AFM Revision Temporary Changes 1.X 4 None Configuration S3-AA U.S. S3-5
PERFORMANCE WARNING THE CPCALC PERFORMANCE THAT IS SHOWN IS FOR THOSE CONDITIONS AS SPECIFIED. ANY DEVIATION FROM THESE CONDITIONS WILL RESULT IN DIFFERENT PERFORMANCE. THERE CAN BE COMBINATIONS OF CONDITIONS (WEIGHT, ALTITUDE AND TEMPERATURE) THAT COULD RESULT IN PERFORMANCE OTHER THAN THAT WHICH WOULD NORMALLY BE EXPECTED: E.G., AS WEIGHT GETS LIGHTER, REQUIRED DISTANCES ARE LONGER. DEFINITIONS Climb Gradient Surface: Imaginary surface located 35 feet above the end of the available runway and inclined at a required gradient. NET TAKEOFF FLIGHT PATH METHODS The airplane is flown to Level Off Altitude per the Gross Takeoff Flight Path. Level Off Altitude is the sum of Airport Barometric Altitude and Takeoff Climb Increment. The Takeoff Climb Increment is based on Gross Takeoff Flight Path which is associated with Net Takeoff Flight Path meeting the requirements of one of the three methods the user specifies. CPCalc provides the level off altitude and the horizontal distances along the net takeoff flight path. The net takeoff flight path is used to plan obstacle clearance. CPCalc will reduce the gross weight, if necessary, to meet specific flight path performance requirements. CPCalc provides three methods for the user to specify net takeoff flight path performance. 1. The net takeoff flight path will level off at a fixed height 1500 feet above the takeoff surface. Figure S3-1 (Continued Next Page) S3-6 U.S. Configuration S3-AA
PERFORMANCE (Continued) 2. The net takeoff flight path may continue the 2 nd segment climb beyond 1500 feet to clear an obstacle located anywhere along the path by at least 35 feet. Figure S3-2 3. The net takeoff flight path may continue the 2 nd segment climb beyond 1500 feet until the aircraft reaches an assigned level off altitude. The net takeoff flight path is prevented from penetrating a defined climb gradient surface. Figure S3-3 Configuration S3-AA U.S. S3-7
DESCRIPTION SOFTWARE PROCEDURES The CPCalc software provides help with detailed information on how to use the CPCalc for calculating Takeoff and Landing performance information. 1. Operational landing distance factor requirements may be set under the menu selection Tools Options, or the keyboard shortcut CTRL+O. 2. Climb Gradient calculator is available under the menu selection Tools Climb Gradient Calculator, or the keyboard shortcut CTRL+G. 3. Help is available under the menu selection Help Contents. For help specific to the screen shown, press the F1 key. 4. The calculated performance data may be printed to a connected printer by selecting the Print All Takeoff or Print All Landing buttons on the appropriate output tabs. 5. Additional condition information is available from each output tab by selecting the Additional Conditions button or the keyboard shortcut Alt+C. SOFTWARE INFORMATION 1. The CPCalc software has been demonstrated to function with the following Microsoft Windows operating system versions: Microsoft Windows 98 SP1, 98SE, or ME Windows NT 4.0 SP4, SP6 Windows 2000 SP3 Windows XP SP1,SP2 Windows Vista 2. The CPCalc software has been demonstrated to work with the following personal computer processors: Pentium II Pentium III Pentium 4 Intel AMD K6 Athlon XP 3. It is recommended that CPCalc be installed on a system that meets the following system requirements: Microsoft Windows operating system (98, ME, NT, 2000, XP, Vista). Minimum CPU 300 MHz, recommended CPU 600 MHz or better (Intel or AMD ). Minimum memory 64 MB, recommended memory 128 MB or higher. 30 MB free disk space for installation. Desktop, laptop, or tablet PC with CD-ROM drive for installation. Input device (keyboard/mouse/pen). Display that supports a resolution of 800 x 600 at 96 DPI or, 1024 x 768 at 120 DPI. Administrative rights to install programs. Microsoft Data Access Components (MDAC) Version 2.5 or higher (included on installation CD). S3-8 U.S. Configuration S3-AA