Homeowners Guide. Bath Whirlpool C K-856-AH

Homeowners Guide Bath Whirlpool K-856-AH M product numbers are for Mexico (i.e. K-12345M) Los números de productos seguidos de M corresponden a México (Ej. K-12345M) Français, page Français-1 Español, página Español-1 1023275-5-C

Important Information INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING: When using electrical products, basic precautions should always be followed, including the following: DANGER: Risk of personal injury. To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times. WARNING: Risk of personal injury. To avoid injury, exercise care when entering or exiting the whirlpool. WARNING: Risk of electric shock. Do not permit electric appliances (such as a hair dryer, lamp, telephone, radio, or television) within 5 (1.5 m) of this whirlpool. WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6 F (37 C). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include: (a) failure to perceive heat, (b) failure to recognize the need to exit the bath, (c) unawareness of impending hazard, (d) fetal damage in pregnant women, (e) physical inability to exit the bath, and (f) unconsciousness resulting in the danger of drowning. WARNING: Risk of hyperthermia. People using medications and/or having an adverse medical history should consult a physician before using a whirlpool equipped with a heater. WARNING: Risk of scalding. Do not allow the water temperature in the whirlpool to exceed 104 F (40 C). The heater will automatically maintain the water temperature when the whirlpool is running, as long as the water temperature does not exceed 104 F (40 C). The heater will disengage at higher temperatures. An equipment grounding terminal is provided in the field wiring compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply panel with a conductor equivalent in size to the circuit conductors supplying this whirlpool. A pressure wire connector is provided on the exterior of the pump or control within this unit to permit connection of a bonding conductor between this unit and all other exposed metal in the vicinity, as needed to comply with local requirements. Use this whirlpool only for its intended purpose as described in this guide. Do not use attachments not recommended by the manufacturer. Never drop or insert any object into any opening. Keep small objects such as bath toys and bathing accessories out of the whirlpool while the unit is running. Do not operate this unit without the guard (cover) over the suction fitting. The whirlpool must be connected only to a supply circuit that is protected by a Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD). Such a GFCI or RCD should be provided by the installer and should be tested on a routine basis. To test the GFCI or RCD, press the test button. The GFCI or RCD should interrupt power. Press the reset button. Power should be restored. If the GFCI or RCD fails to operate in this manner, the GFCI or RCD is defective. If the GFCI or RCD interrupts power to the bath without the test button being pressed, a ground current is flowing, indicating the possibility of an 1023275-5-C 2 Kohler Co.

Important Information (cont.) electric shock. Do not use this whirlpool bath. Disconnect the whirlpool and have the problem corrected by a qualified service representative before using. Flush your whirlpool system twice a month or more depending upon usage, as described in the Flush System section of this guide. Repeated use of personal care products containing oils can damage plastic whirlpool components. Do not use heavy, vegetable-based shampoos or bath oils. Whirlpool hydro-massage action can cause even a small amount of bubble bath, bath soap, shampoo, or bath oil to foam excessively. For this reason, please don t use these products during whirlpool operation. FCC Compliance FCC ID : N82-KOHLER001 Canada ID : 4554A-KOHLER001 Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning (Part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Table of Contents Important Information... 2 FCC Compliance... 3 Thank You For Choosing Kohler Company... 3 Your Kohler Whirlpool... 4 Lighted User Keypad... 5 Operation... 6 Remote Control... 8 Flush System... 9 Care and Cleaning... 9 Warranty... 9 Warranty... 10 Warranty... 10 Service the Effervescent Ports... 12 Troubleshooting... 13 Service Parts... 16 Thank You For Choosing Kohler Company Thank you for choosing Kohler Co. Your Kohler Co. product reflects the true passion for design, craftsmanship, artistry, and innovation Kohler Co. stands for. We are confident its dependability and beauty will surpass your highest expectations, satisfying you for years to come. All information in this guide is based upon the latest product information available at the time of publication. At Kohler Co. we strive to fulfill our mission of improving the level of gracious living for each person who is touched by our products and services. We reserve the right to make changes in product characteristics, packaging, or availability at any time without notice. Please take a few minutes to review this guide. Pay special attention to the care and cleaning instructions. Kohler Co. 3 1023275-5-C

Your Kohler Whirlpool Your new whirlpool is designed to stimulate, invigorate, and energize your body with comforting hydro-massage therapy. The whirlpool consists of the following components: Remote Control - Places the whirlpool functions at your fingertips to further enhance your bathing experience. The functions of the remote control are identical to the lighted user keypad. Pump Motor - Provides quiet, variable speed power to circulate the water. Adjustable Jets - Positioned to optimize their hydro-massage effect, the jets allow you to adjust the air and water flow and control the flow direction as you desire. Heater - Automatically helps maintain a 104 F (40 C) water temperature, turns on when the whirlpool is operating, and turns off when the pump motor is turned off. Using the lighted user keypad, the heater may be turned off at any time while the pump is operating. Effervescence - Eight effervescent ports emit thousands of champagne-like bubbles which provides a relaxing, soothing experience. Chromatherapy - Promotes relaxation and delivers a full spectrum of color. Chromatherapy may be used with all modes of operation, even when the pump is not operating. Lighted User Keypad - Located within easy reach, allows you to turn the whirlpool on and off. It also allows you to access all the whirlpool modes and regulate the water flow or pulse speed. 1023275-5-C 4 Kohler Co.

Flexjet Flow Mode Activates Mode Selected Rotate outer ring to access desired mode. Power On/Off Chromatherapy - Specific Color Increases Flow or Pulse Indicator Bar Effervescence Mode Decreases Flow or Pulse Chromatherapy Cycle Heater On/Off Lighted User Keypad Available modes will be illuminated in blue. Active modes will be illuminated in green. Power Turns the whirlpool pump on and off. Icons illuminated in blue indicate available modes/features. Modes which are operating will be illuminated in green. Outer Ring Rotate the outer ring to the desired mode. The selected mode will flash blue. OK Activates the desired mode. Flexjet Flow When illuminated, the adjustable jet water flow can be adjusted by pressing the up or Mode down arrow. Up Arrow Increases the water flow when the Flexjet flow mode is active. Indicator Bar Displays the water flow volume in the Flexjet flow mode. Effervescence Ports activate to provide a gentle, soothing bubbling action. The Flexjet mode will Mode automatically turn off when this mode is activated. Down Arrow Decreases the water flow when the Flexjet flow mode is active. Chromatherapy Chromatherapy lights will automatically and continuously cycle through the eight colors: Cycle white, violet, indigo blue, aqua blue, green, yellow, orange, and red. One cycle through all eight colors takes approximately one minute. Heater Automatically engages when the power icon is selected. Rotate the outer ring until the heater mode is flashing, then press OK to turn the heater off. Press OK again to turn the heater back on. Chromatherapy - Specific Color Press OK to activate, then use the up or down arrow to reach the desired color. Press OK while the chromatherapy cycle is active to turn off the chromatherapy lights. Kohler Co. 5 1023275-5-C

Fill with water at least 2" (5.1 cm) above the highest jet. Turn the jet trim ring clockwise to decrease the flow. Position the jet nozzles to direct the water flow as desired. Turn the jet trim ring counterclockwise to increase the flow. Operation NOTE: If the whirlpool is not operating properly, consult the Troubleshooting section of this guide before calling a qualified service representative. Whirlpool Turn the jet trim fully counterclockwise. Position the jet nozzles so they face down toward the basin. NOTICE: Do not allow the water temperature in the whirlpool to exceed 104 F (40 C). The heater will automatically maintain the water temperature when the whirlpool is running, as long as the water temperature does not exceed 104 F (40 C). The heater will disengage at higher temperatures. Close the drain, then fill the whirlpool to a level at least 2 (5.1 cm) above the highest jet. Using your hand, test the water temperature for comfort and safety. Carefully enter the bath. Press the power icon to turn on the whirlpool pump and heater. Water will flow at medium volume. Press the up or down arrow icons to increase or decrease the water flow. The indicator bar will display the water flow volume. Adjust the jets for optimum air/water mixture. Turn the jet trim clockwise to reduce the flow or counterclockwise to increase the flow. If desired, position the jet nozzles to direct the water flow to maximize your hydro-massage experience. If desired, turn the heater off by pressing the heater icon. Press the button a second time to turn the heater back on. Press the power icon a second time to turn off the whirlpool pump and heater. NOTE: The pump and heater will automatically stop after approximately 20 minutes of continuous operation. If desired, press the power icon to reactivate the pump and heater. Carefully exit the bath, then open the drain to empty the whirlpool. Effervescence Rotate the outer ring until the effervescence icon is flashing, then press OK to activate the effervescence ports. The water flow volume will remain as previously set. Press OK while the effervescence mode is flashing to turn off the effervescence ports. Chromatherapy NOTE: The chromatherapy modes may be used with all modes of operation, even when the pump is not operating. 1023275-5-C 6 Kohler Co.

Operation (cont.) Rotate the outer ring to select the chromatherapy mode, then press OK to activate the chromatherapy lights. Press OK while the chromatherapy mode is active to turn off the chromatherapy lights. Rotate the outer ring to select chromatherapy specific color selection, then press OK. Use the up or down arrow to reach the desired color. Press OK while the chromatherapy specific color selection is active to turn off the chromatherapy lights. Kohler Co. 7 1023275-5-C

Power Activates Mode Selected Increases Flow or Pulse Mode Selector Decreases Flow or Pulse Remote Control Operate The remote control, which functions are identical to the user keypad, places the whirlpool functions at your fingertips to further enhance your bathing experience. The remote control is waterproof, so it may be used in the bath and will float in the water. Power Mode Selector OK Up Arrow Down Arrow Turn the whirlpool or heater on and off. Functions in the same way as the outer ring on the user keypad. When pressed, one of the modes will flash on the user keypad. When pressed again, the next mode in clockwise order will flash. When the desired mode is flashing, press OK to activate it. Activates the desired mode. Increases the water flow or pulse. Decreases the water flow or pulse. Program NOTE: Programming of the remote control is normally not required. However, programming the remote control to the user keypad may be necessary if: (1) more than one device in or near the vicinity of your home uses a remote control or (2) you replace your remote control or pump control. Turn the whirlpool power on. Turn off all modes of operation. Wait approximately one minute until the keypad darkens completely (sleep mode). On the user keypad, press the up arrow, down arrow, and the OK button simultaneously. The bottom LED on the user keypad indicator bar will begin flashing. While the bottom LED is flashing, press the OK button on the user keypad. A light sequence will illuminate up and down the indicator bar. While the light sequence is active, press any button on the remote control. The program will download and the user keypad will darken. The user keypad will now respond only to this remote control. Batteries Unscrew the end cap of the remote control, as shown. Insert two AAA batteries. Securely tighten the end cap, making sure the end cap contacts the seal. 1023275-5-C 8 Kohler Co.

Flush System NOTE: Flush your whirlpool system twice a month or more, depending upon usage. Turn the jet trim rings fully clockwise to remove air induction. Fill the whirlpool with warm water to a level at least 2 (5.1 cm) above the highest jets, or leave water in the whirlpool after using. Add 2 teaspoons (10 ml) of a low-foaming, powder automatic dishwasher detergent and 20 ounces (590 ml) of household bleach (5% - 6% sodium hypochlorite) to the water. Run the whirlpool for 5 to 10 minutes. Turn off the whirlpool and drain. If desired, rinse the bath surfaces with water. Rinse the surfaces of the jets, faucet, handrails, and drain, and wipe them dry with a soft cloth. Care and Cleaning For best results, keep the following in mind when caring for your KOHLER product: Always test your cleaning solution on an inconspicuous area before applying to the entire surface. Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and dry any overspray that lands on nearby surfaces. Do not allow cleaners to soak on surfaces. Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring pad to clean surfaces. The ideal cleaning technique is to rinse thoroughly and blot dry any water from the surface after each use. Use a soft nylon brush on Safeguard slip-resistant surfaces. Be sure to use a water-soluble cleaner (dissolves 100% in water). For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care & Cleaning information, call 1-800-456-4537. Warranty ONE-YEAR LIMITED WARRANTY KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year from date of installation. Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not responsible for removal or installation costs. Use of in-tank toilet cleaners will void the warranty. To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com in Mexico. IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state/province to state/province. This is Kohler Co. s exclusive written warranty. Kohler Co. 9 1023275-5-C

Warranty Kohler Co. warrants the cast iron components of products manufactured after February 10, 2000, to be free of defects in material and workmanship during normal residential use for as long as the original consumer purchaser owns his or her home. Gloss reduction, scratching, staining and alkaline etching of the finish over time due to use, cleaning practices or water or atmospheric conditions, are not manufacturing defects but are indicative of normal wear and tear. This warranty applies only for KOHLER Cast Iron products installed in the United States of America, Canada or Mexico (North America). If a defect is found in normal residential use, Kohler Co. will, at its election, repair, replace or make appropriate adjustment. Damage caused by accident, misuse, or abuse is not covered by this warranty. Improper care and cleaning will void the warranty. Proof of purchase (original sales receipt) must be provided to Kohler Co. with all warranty claims. Kohler Co. is not responsible for labor charges, installation, or other incidental or consequential costs. In no event shall the liability of Kohler Co. exceed the purchase price of the product. If the cast iron product is used commercially or is installed outside of North America, Kohler Co. warrants the cast iron product to be free from defects in material and workmanship for one (1) year from the date the product is installed, with all other terms of this warranty applying except duration. All other components other than the enameled cast iron carry Kohler Co. s one-year limited warranty unless otherwise specified. If you believe that you have a warranty claim, contact Kohler Co., either through your Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing: Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA. Please be sure to provide all pertinent information regarding your claim, including a complete description of the problem, the product, model number, color, finish, the date the product was purchased and from whom the product was purchased. Also include your original invoice. For other information, or to obtain the name and address of the service and repair facility nearest you call 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com in Mexico. Kohler Co. and/or seller are providing this warranty in lieu of all other warranties, expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Kohler Co. and/or seller disclaims any liability for special, incidental or consequential damages. Some states/provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives the consumer specific legal rights. You may also have other rights, which vary, from state/province to state/province. This warranty is to the original consumer purchaser only, and excludes product damage due to installation error, product abuse, or product misuse, whether performed by a contractor, service company or the consumer. This is Kohler Co. s exclusive written warranty. Warranty KOHLER CO. It is recommended that at the time of purchase, you verify that all accessories and components are complete in this package. This Kohler product is warranted to be free of defects in material and workmanship for one (1) year from the date of purchase as shown on the invoice or receipt. 1. Kohler Co. will only service its commercialized products through its authorized distributors. 2. To obtain warranty service, please present the invoice and corresponding warranty. 3. Through its authorized distributors, Kohler Co. promises to repair the defective product or provide a new replacement or an equivalent model (in those cases that the model has been discontinued) when the product is beyond repair, without any charge to the consumer. 4. The time of repair will not exceed six (6) weeks commencing on the date the product is received. 5. It is recommended that the consumer save the invoice or receipt as additional protection, as it may substitute the warranty in the case that there is a discrepancy in the validity of the warranty. 1023275-5-C 10 Kohler Co.

Warranty (cont.) EXCEPTIONS AND RESTRICTIONS The Warranty will not be valid in the following cases: 1. When the product is not operated in accordance with the instructions concerning use and operation set forth in the owner s manual or installation instructions, and when the recommendations and warnings included are not observed. 2. When the product has been modified or dismantled partially or totally; or has been used in a negligent fashion and as a consequence has suffered damages attributable to the consumer, individual, or hardware not authorized by Kohler Co. 3. This warranty does not cover the damages as a result of disaster such as fire or acts of God, including flooding, earthquake, or electric storms, etc. To obtain a list of distributors in your area where you can exercise your rights under this warranty, please call 001-800-456-4537. KOHLER CO., KOHLER, WI 53044 U.S.A. IMPORTER: INTERNACIONAL DE CERÁMICA, S.A.B. DE C.V. AV. CARLOS PACHECO NO. 7200 CHIHUAHUA, CHIH., MEXICO C.P. 31060 TEL: 52 (14) 29-11-11 Kohler Co. 11 1023275-5-C

Housing Flange Removal Tool Flange Whirlpool Service the Effervescent Ports NOTICE: This section is for general aid only. A Kohler Authorized Service Representative or qualified electrician should correct any electrical problems. For warranty service, contact your dealer or wholesale distributor. Remove the Port Insert the flange removal tool (provided) into the opening of the port. Place your thumb against the whirlpool wall while firmly grasping the flange removal tool. Pull the flange removal tool until the flange pulls free from the housing. Reinstall the Port NOTE: Do not use force when reinstalling the port. Carefully insert the flange into the housing, then lightly push and rotate the flange until it snaps into position. Verify the port is installed correctly. Remove and reinstall, if necessary. 1023275-5-C 12 Kohler Co.

Remove the Jets Insert the tool hook as shown and pull the jet out of the housing. The jet should be facing up when this is done. Reinstall the Jets Housing Inspect and lubricate the O-ring. Slide the O-ring onto the first shoulder of the jet. Insert the jet into the housing, and lightly push and rotate until it snaps in position. Troubleshooting NOTICE: This section is for general aid only. A Kohler Authorized Service Representative or qualified electrician should correct any electrical problems. For warranty service, contact your dealer or wholesale distributor. Remove the Jets Position the ball nozzle of the jet facing up. This will ensure the jet tool will not slip off. Position the jet tool (provided) with the hook facing up. Insert the jet tool into the opening of the jet and hook the inside top of the nozzle. Place your thumb against the whirlpool wall while firmly grasping the jet tool. Steadily pull the jet tool until the jet assembly pulls free from the housing. Be careful not to lose the O-ring. Reinstall the Jets NOTE: To allow easy rotation and proper operation of the jet, the O-ring must be: (1) correctly positioned, (2) lubricated, and (3) in good condition. Install the O-ring onto the first shoulder of the jet. Using the silicone lube packet (provided), lubricate the O-ring to prevent noisy operation of the jet. Carefully insert the jet into the housing, then lightly push and rotate the jet until it snaps into position. Do not force the jet. Verify the jet is installed correctly. The jet should turn smoothly both clockwise and counterclockwise. Remove and reinstall, if necessary. Troubleshooting Table User Keypad and Pump Symptoms Probable Causes Recommended Action 1. User keypad does A. No power to control. A. Check wiring and connect power. not illuminate when B. GFCI or RCD tripped. B. Reset GFCI or RCD. power button is pressed or outer ring C. Wiring harness from user C. Check wiring for proper connections. is rotated. keypad to control is loose, Replace wiring harness if necessary. disconnected or damaged. D. User keypad does not work. D. Replace user keypad. E. Control does not work. E. Replace control. Kohler Co. 13 1023275-5-C

Troubleshooting (cont.) User Keypad and Pump Symptoms Probable Causes Recommended Action 2. Motor starts, but all jets are not A. Jet is closed. A. Rotate jet trim counterclockwise to open. functioning. B. Jet not installed correctly. B. Reinstall jet; check for O-ring damage. C. Jets are blocked. C. Remove blockage. 3. User keypad is illuminated, but does not respond to buttons or outer ring. 4. User keypad indicator bar keeps scanning at power-up. 5. User keypad is illuminated, but pump will not start. 6. Motor runs but pump will not prime (cavitates). 7. Pump stops before 18 minutes. 8. Pump does not automatically stop after 22 minutes. 9. Pump will not turn off when the power button on user keypad is pressed. 10. Pump operates but variable speed feature does not work. 11. Bath water cools while pump is operating. A. Control program is locked. A. Reset GFCI or RCD. B. Wiring harness from user keypad to control is loose, B. Check wiring for proper connections. Replace wiring harness if necessary. disconnected or damaged. C. User keypad does not work. C. Replace user keypad. D. Control does not work. D. Replace control. A. Control program is locked. A. Reset GFCI or RCD. B. Wiring harness from user keypad to control is loose, disconnected or damaged. B. Check wiring for proper connections. Replace wiring harness if necessary. C. User keypad does not work. C. Replace user keypad. D. Control does not work. D. Replace control. A. Power cord from pump to A. Check wiring for proper connections. control is loose, disconnected or damaged. B. Pump does not work. B. Replace pump. C. Control does not work. C. Replace control. A. Pump is shimmed too high. A. Lower pump/control to subfloor level. B. Small air leak at pump inlet. B. Securely tighten nut(s) on intake side of pump. C. Motor/pump does not work. C. Replace motor/pump. D. Control does not work. D. Replace control. A. GFCI or RCD tripped. A. Identify source of fault, and correct. Reset GFCI or RCD. B. Suction is blocked. B. Remove obstruction. C. Jets are blocked. C. Remove blockage. D. Motor overheated and protection D. Check for blockage at suction and/or device activated. jets. Remove blockage and allow motor to cool. A. 20-minute timer inadvertently A. See service manual. disabled. A. User keypad does not work. A. Replace user keypad. B. Control does not work. B. Replace control. A. Motor/pump does not work. A. Replace motor/pump. B. Control does not work. B. Replace control. A. Water temperature above 104 F A. Allow bath water to cool. (40 C). B. Heater is turned off on user B. Turn heater on. keypad. C. Wiring from heater to control is loose, disconnected or damaged. C. Check wiring for proper connections. D. Heater does not work. D. Replace heater. E. Control does not work. E. Replace control. 1023275-5-C 14 Kohler Co.

Troubleshooting (cont.) User Keypad and Pump Symptoms Probable Causes Recommended Action 12. Noisy operation. A. Pump banding straps have not been cut. A. Cut pump banding straps with tin snips. B. Dry or dislodged jet O-ring (squeal). B. Remove jet, replace and lubricate O-ring, and reinstall jet. Effervescent Ports Symptoms Probable Causes Recommended Action 1. Effervescent ports do not A. Whirlpool pump is not A. Turn on pump. work. operating. B. Butterfly valve does not work. B. Replace butterfly valve. C. Pump does not work. C. Refer to the service manual to troubleshoot the system. Refer to installer/dealer. D. Control does not work. D. Replace control. 2. Effervescent ports do not A. Air intake on suction line is A. Remove blockage. bubble. blocked. B. Water flow is too low. B. Increase water flow. Chromatherapy Lights Symptoms Probable Causes Recommended Action 1. Chromatherapy lights do not work. A. Loose, disconnected or damaged wiring/connections. A. Check wiring for proper connections. Replace wiring if necessary. B. Control does not work. B. Replace control. Remote Control Symptoms Probable Causes Recommended Action 1. Remote control does not A. Batteries improperly installed or A. Replace batteries. work. dead. B. Antenna on wiring harness is B. Replace wiring harness. damaged. C. Remote control not programmed correctly. C. See homeowners guide or service manual. D. Remote control does not work. D. Replace remote control. E. Control does not work. E. Replace control. Kohler Co. 15 1023275-5-C

93841 Screw 1019933 Chromatherapy Lights 1010618 Elbow 1012821 Light Housing 93836 (1/2") 93837 (3/4") 93838 (1") 93839 (1-1/4") 94853 (1-1/2") Tube (w/couplings) 1003065 Suction Flange Removal Tool 96708 Flange 73518 Plug 93685 Housing 91967 Check Valve 1023292 Cap 1015008 Wire Harness 1015017 Plug/Wire Assembly 65054** Screw 65226** Suction Cover Plug 65886 (Acrylic and FRP) 60050 (Cast Iron) Gasket 96895** (Colored Finishes) 65061** (Metal Finishes) Cover Effervescence Ports 93315 Gasket 1001878 Housing 93552** Flange Cap 1035480** Flange 96744 Flange Removal Tool **Finish/color code must be specified when ordering Service Parts 1023275-5-C 16 Kohler Co.

1003065 Suction Flange Removal Tool 73518 Plug 93685 Housing 96708 Flange 65054** Screw 65226** Suction Cover Plug 65886 (Acrylic and FRP) 60050 (Cast Iron) Gasket 96895** (Colored Finishes) 65061** (Metal Finishes) Cover 93836 (1/2") 93837 (3/4") 93838 (1") 93839 (1-1/4") 94853 (1-1/2") Tube (w/couplings) 91967 Check Valve 1086350 Flange Removal Wrench 67665 Plug 34353 O-Ring 30739 Jet Tool 1045715-P Silicone Lube Packet 67429 Flange 67889 Jet Housing 65885 (Acrylic and FRP) 67668 (Cast Iron) Gasket Single Jet For Whirlpools With 5 or Less Jets 88532** (Colored Finishes) 88531** (Metal Finishes) Jet Single Jet For Whirlpools With 6 or More Jets 88530** (Colored Finishes) 88529** (Metal Finishes) Jet **Finish/color code must be specified when ordering. Kohler Co. 17 1023275-5-C

67065 Ground Lug 61776 Lock Washer 60320 Screw 60320 Screw 1033678 Screw 93892-A Electrical Box 67065 61776 Lock Washer Ground Lug 1001794 Locknut 1018964 Bracket 61845-K Copper Grounding Wire 94821 O-Ring 1080774 Union Assy 93893 Cover 93003 Strain Relief 1019433 Carriage Bolt 1080775 Pump Tee 94821 O-Ring To Tee Heater 90153 Locknut 1016953 Pump 1016954 Motor 1010548 Volute 1010673 Seal 1010676 Cover 1010677 Screw 1013755 Impeller 1019719 Connector 1012855 Nut 94821 O-Ring To In-line Heater 1010675 O-Ring 1019444-A [3/4" (1.9 cm)] 1019444-B [1-3/4" (4.4 cm)] 1019444-C [2" (5.1 cm)] 1019444-D [1-1/2" (3.8 cm)] 1019444-E [1" (2.5 cm)] 1019444-F [1-1/4" (3.2 cm)] 1019444-G [2-1/4" (5.7 cm)] 1019444-H [2-1/2" (6.4 cm)] 1019444-J [2-3/4" (7 cm)] 1019444-K [3" (7.6 cm)] 1019444-L [1/2" (1.3 cm)] 1019444-M [1/4" (6 mm)] Spacer 1019446-A [1-3/4" (4.4 cm)] 1019446-B [2-3/4" (7 cm)] 1019446-C [3" (7.6 cm)] 1019446-D [2-1/2" (6.4 cm)] 1019446-E [2" (5.1 cm)] 1019446-F [2-1/4" (5.7 cm)] 1019446-G [3-1/4" (8.3 cm)] 1019446-H [3-1/2" (8.9 cm)] 1019446-J [3-3/4" (9.5 cm)] 1019446-K [4" (10.2 cm)] 1019446-L [1-1/2" (3.8 cm)] 1019446-M [1-1/4" (3.2 cm)] Stud 1018660 (One Outlet) 1018662(Two Outlets) Control Outlet 1019447-A [1/4" (6 mm)] 1019447-B [1/2" (1.3 cm)] 1019447-C [3/4" (1.9 cm)] Isolation Mount **Finish/color code must be specified when ordering. 1023275-5-C 18 Kohler Co.

1022408 In-line Heater 1032545 Housing 1012653 Adapter 1012916 Nut w/screws 94821 O-Ring 1012653 Adapter 94821 O-Ring 1011679 Gasket 1012977 Adapter 1018710 Tee Heater 1012916 Nut with Screws 94821 O-Ring 94821 O-Ring 1012977 Adapter 1011679 Gasket **Finish/color code must be specified when ordering. Kohler Co. 19 1023275-5-C

1020677 Gasket 1023381 Wrench 1013453 Spring 65157 Nut Carefully study decal and cover detail below for proper service part identification. 1013452** Dial Trim 91639 O-Ring 1013499 Housing 1020678-A Cover/Circuit Board (w/wrench) 1020678-B Cover/Circuit Board (w/wrench) 91639 O-Ring 91639 O-Ring 1020678-C Cover/Circuit Board (w/wrench) 1013497-A Decal 1020678-D Cover/Circuit Board (w/wrench) 1013497-B Decal 1020678-E Cover/Circuit Board (w/wrench) 1013497-C Decal 91639 O-Ring 1020678-M Cover/Circuit Board (w/wrench) 1013497-D Decal 91639 O-Ring 1020678-N Cover/Circuit Board (w/wrench) 1013497-E Decal 91639 O-Ring 1020678-P Cover/Circuit Board (w/wrench) 1013497-M Decal 91639 O-Ring 1013497-N Decal 91639 O-Ring 1013497-P Decal 91639 O-Ring **Finish/color code must be specified when ordering. 1023275-5-C 20 Kohler Co.

1013822-A** Remote w/stand 1013464-A Decal 1023091** Cap 1013471** Stand 1022253-A** Remote 1013822-B** Remote w/stand 1013464-B Decal 1023091** Cap 1022253-B** Remote 1013471** Stand **Finish/color code must be specified when ordering. Kohler Co. 21 1023275-5-C

Guide du propriétaire Baignoire à hydromassage Renseignements importants CONSIGNES RELATIVES AUX RISQUES D INCENDIE, D ÉLECTROCUTION OU DE BLESSURES CORPORELLES LIRE ET SUIVRE TOUTES LES INSTRUCTIONS CONSERVER CES INSTRUCTIONS AVERTISSEMENT : Lors de l utilisation des produits électriques, des précautions de base doivent toujours être observées, incluant ce qui suit : DANGER : Risque de blessures corporelles. Afin de réduire les risques de blessures, ne jamais permettre à un enfant d utiliser cet appareil sans surveillance. AVERTISSEMENT : Risque de blessures corporelles. Pour éviter les blessures corporelles, entrer et sortir avec précaution de la baignoire à hydromassage. AVERTISSEMENT : Risque d électrocution. Ne pas raccorder d appareils électriques (tels que sèche-cheveux, lampe, téléphone, radio ou télévisions) dans les 5 (1,5 m) de cette baignoire à hydromassage. AVERTISSEMENT : La consommation d alcool, de drogues ou de médicaments peuvent augmenter considérablement le risque fatal d hyperthermie. Une immersion prolongée dans l eau chaude peut provoquer l hyperthermie. L hyperthermie a lieu lorsque la température corporelle interne atteint plusieurs degrés au dessus de la température normale de 98,6 F (37 C). Les symptômes d hyperthermie comprennent la hausse de la température corporelle, l étourdissement, la léthargie, la somnolence et l évanouissement. Les effets de l hyperthermie comprennent: (a) défaut de percevoir la chaleur, (b) défaut de s apercevoir du besoin de sortir de la baignoire, (c) incapacité de reconnaître le danger, (d) dommages au foetus dans le cas des femmes enceintes, (e) incapacité physique de sortir de la baignoire et (f) inconscience et danger conséquent de noyade. AVERTISSEMENT : Risque d hyperthermie. Les personnes sous médicaments ou qui sont en observation médicale doivent consulter leur médecin avant d utiliser des baignoires à hydromassage équipées de chauffe-eau. AVERTISSEMENT : Risque de brûlures. Ne pas laisser la température de la baignoire à hydromassage excéder 104 F (40 C). Un chauffe-eau maintient automatiquement la température d eau quand la baignoire à hydromassage est en marche, et tant que la température d eau ne dépasse pas 104 F (40 C). Le chauffe-eau s arrêtera aux températures plus hautes. Une borne de mise à la terre est incluse dans le boîtier du câblage. Afin de réduire les risques d électrocution, ce terminal doit être raccordé à la borne de mise à la terre du panneau du service électrique, avec un câble ayant le même calibre que celui du circuit de contrôle qui alimente cet équipement. Un connecteur à pression par câble est prévu à l extérieur de la pompe ou de la commande de cet appareil afin de permettre la connexion entre l appareil et toutes autres surfaces de métal avoisinantes, tel que requis par les normes locales. Kohler Co. Français-1 1023275-5-C

Renseignements importants (cont.) Utiliser cette baignoire à hydromassage uniquement pour un usage tel que décrit dans ce guide. Ne pas utiliser des fixations non recommandées par le fabricant. Ne jamais faire tomber ou insérer d objet quelconque dans les ouvertures. Ne pas laisser de petits objets tels que des jouets ou accessoires pour le bain dans la baignoire à hydromassage lorsqu elle est en marche. Ne pas utiliser cet appareil sans ses protecteurs (couvercles) sur ses raccords d aspiration. La baignoire à hydromassage doit être raccordée uniquement à une prise de terre, protégée par un disjoncteur différentiel (GFCI) ou un appareil de courant résiduel (RCD). De tels disjoncteurs GFCI ou RCD devraient être fournis par l installateur et vérifiés régulièrement. Appuyer sur le bouton de test pour tester les disjoncteurs GFCI ou RCD. Le GFCI ou RCD devraient couper le courant. Appuyer sur le bouton de ré-initialisation. L alimentation devrait être restituée. Si les disjoncteurs GFCI or RCD ne fonctionnent pas de cette façon, l un ou l autre est défectueux. Si les disjoncteurs GFCI ou RCD stoppent l alimentation électrique à la baignoire sans que le bouton test ne soit utilisé, il y a donc un court circuit indiquant la possibilité de choc électrique. Ne pas utiliser pas cette baignoire à hydromassage. Débrancher la baignoire à hydromassage et la faire réviser par un technicien qualifié avant son utilisation. Purger le système d hydromassage deux fois par mois ou plus souvent selon la fréquence d usage, tel que décrit dans la section «Purger le système» de ce guide. L utilisation répétée de produits d hygiène et de beauté contenant des huiles peut endommager les revêtements en plastique des composants de la baignoire à hydromassage. Ne pas utiliser de shampoings ou d huiles de bains à bases végétales. L action de la baignoire à hydromassage peut considérablement faire mousser une quantité de produit moussant, même très petite, de savon, de shampoing ou d huile pour le bain. Pour cette raison, nous vous conseillons de ne pas utiliser ces produits dans votre baignoire à hydromassage. Conforme FCC FCC ID: N82-KOHLER001 Canada ID: 4554A-KOHLER001 Déclaration de conformité (Partie 15.19) Cet appareil est conforme avec la Partie 15 de la réglementation FCC et RSS-210 Canada Industrie. L appareil est soumis aux deux conditions d exploitation suivantes : 1. Cet appareil ne devrait pas causer d interférences dangereuses, et 2. Cet appareil doit recevoir les toutes interférences reçues, ainsi que celles qui pourraient causer des opérations non désirées. Danger (Partie 15.21) Tous changements ou modifications non expressément approuvés par la partie responsable garantissant la conformité, pourrait annuler le droit à l opérateur d utiliser l équipement. Kohler Co. Français-2 1023275-5-C

Sommaire Renseignements importants... 1 Conforme FCC... 2 Merci d avoir choisi la compagnie Kohler... 3 Votre baignoire à hydromassage Kohler... 3 Clavier de l utilisateur illuminé... 4 Opération... 5 Télécommande... 7 Système de chasse... 8 Entretien et nettoyage... 8 Garantie... 8 Garantie... 9 Entretenir les ports effervescents... 10 Dépannage... 11 Pièces de rechange... 15 Merci d avoir choisi la compagnie Kohler Merci d avoir choisi Kohler Co. Vos produits Kohler Co. sont l expression d une vraie passion pour la conception, le travail soigné, le caractère artistique et l innovation représentés par Kohler Co. Nous sommes confiants que sa fiabilité et beauté surpasseront vos exigences les plus élevées, vous satisfaisant pendant les années à venir. Toute information contenue dans ce guide est basée sur l information la plus récente du produit disponible au moment de la publication. Chez Kohler Co, nous aspirons à remplir notre mission d améliorer le niveau d un mode de vie agréable pour chaque personne affectée par nos produits et services. Nous nous réservons le droit d apporter des modifications aux caractéristiques, aux emballages et à la disponibilité des produits à tout moment, et ce sans préavis. Veuillez prendre s il vous plaît quelques minutes pour étudier ce guide. Prêter une attention toute particulière aux instructions d entretien et de nettoyage. Votre baignoire à hydromassage Kohler Votre nouvelle baignoire à hydromassage est conçue pour relaxer, stimuler, revigorer et tonifier votre corps. La baignoire à hydromassage consiste en les éléments suivants: Télécommande - Toutes les fonctions de la baignoire à hydromassage sont à portée de main, afin d améliorer d avantage votre expérience de bain. Les fonctions de la télécommande sont identiques à celles du clavier de l utilisateur illuminé. Moteur de pompe - Fournit une alimentation à vitesse variable et non bruyante pour faire circuler l eau. Jets réglables - Positionnés de manière stratégique pour optimiser l effet d hydromassage, ils permettent d ajuster le débit d air et d eau, ainsi que de contrôler la direction du jet selon le désir. Chauffe-eau - Aide automatiquement à maintenir une température d eau de 40 C (104 F), se met en marche lorsque la baignoire à hydromassage fonctionne et s arrête lorsque le moteur de la pompe est arrêté. Utiliser le clavier de l utilisateur illuminé pour arrêter le chauffe-eau n importe quand pendant que la pompe fonctionne. Effervescence - Huit ports effervescents émettent des milliers de bulles du style bulles de Champagne qui offrent une expérience relaxante et apaisante. Chromathérapie - Encourage la relaxation et fournit un spectre complet de couleur. La chromathérapie peut être utilisée avec tous les modes d opération, même lorsque la pompe n est pas en marche. Clavier illuminé de l utilisateur - Simple d accès, il vous permet de démarrer ou d arrêter la baignoire à hydromassage. Il vous permet aussi d accéder à tous les modes de la baignoire à hydromassage et au réglage du débit d eau ou de la puissance d impulsion. 1023275-5-C Français-3 Kohler Co.

Mode débit Flexjet Active le mode sélectionné Tourner la bague extérieure pour accéder au mode désiré. Marche/arrêt Chromathérapie - Couleur spécifique Augmente le débit ou d'impulsion Barre d'indication Mode effervescence Diminue le débit ou l'impulsion Cycle chromathérapie Chauffeau marche/arrêt Clavier de l utilisateur illuminé Les modes disponibles sont allumés en bleu. Les modes actifs seront illuminés en vert. Alimentation Met les pompes de la baignoire à hydromassage en marche et arrêt. Les symboles illuminés en bleu indiquent la disponibilité des modes/fonctions. Les modes en opération seront illuminés en vert. Anneau extérieur Tourner la bague extérieure pour accéder au mode désiré. Le mode sélectionné clignotera (en bleu). OK Active le mode désiré. Mode débit jets Lorsqu il est illuminé, le débit d eau réglable du jet peut être ajusté en appuyant sur les de type Flexjet flèches haut et bas. Flèche haut Augmente le débit d eau quand le mode Flexjet est actif. Barre indicatrice Indique le volume du débit d eau sous le mode Flexjet. Mode Les ports effervescence s activent pour créer une action douce, relaxante à bulles d air. Le effervescence mode Flexjet s arrête automatiquement quand ce mode est activé. Flèche bas Augmente le débit de l eau quand le mode Flexjet est actif. Cycle de Les lumières de chromathérapie s illumineront automatiquement et de manière continue à chromathérapie travers un cycle de huit couleurs: blanc, violet, bleu indigo, aigue-marine, verte, jaune, orange et rouge. Un cycle des huit couleurs dure à peu près une minute. Chauffe-eau S active automatiquement lorsque la baignoire à hydromassage est mise en service. Pivoter la bague extérieure jusqu à que le mode débit clignote et appuyer sur OK. Appuyer encore une fois sur «OK» pour remettre le chauffe-eau en fonction. Chromathérapie - Couleur spécifique Appuyer sur OK pour l activer, puis utiliser les flèches vers le haut ou vers bas pour obtenir la couleur désirée. Appuyer sur OK quand le cycle de chromathérapie est activé pour éteindre les lumières de chromathérapie. Kohler Co. Français-4 1023275-5-C

Remplir d'eau au-moins à 2" (5,1 cm) au-dessus du jet le plus élevé. Tourner la bague du jet vers la droite pour diminuer le débit. Orienter les jets pour diriger le débit d'eau en position désirée. Tourner la bague du jet vers la gauche pour augmenter le débit d'eau. Opération REMARQUE : Si la baignoire à hydromassage ne fonctionne pas correctement, consulter la section «Dépannage» de ce guide avant d appeler un représentant en service qualifié. Baignoire à hydromassage Tourner complètement la bague du jet vers la gauche. Orienter les buses des jets vers le fond du bassin. AVIS : Ne pas laisser la température de la baignoire à hydromassage excéder 104 F (40 C). Un chauffe-eau maintient automatiquement la température d eau quand la baignoire à hydromassage est en marche, et tant que la température d eau ne dépasse pas 104 F (40 C). Le chauffe-eau s arrêtera aux températures plus hautes. Fermer le drain, puis remplir la baignoire à hydromassage à un niveau d au moins 2 (5,1 cm) au-dessus du jet le plus élevé. Utiliser votre main pour tester la température de l eau pour le confort et la sécurité. Entrer dans la baignoire avec précaution. Appuyer sur l icône de marche pour démarrer la pompe et le chauffe-eau de la baignoire à hydromassage. Le débit d eau aura un volume moyen. Presser les flèches haut/bas pour augmenter ou diminuer le volume de débit d eau. La barre indicatrice affiche le volume du débit d eau. Ajuster les jets pour un mélange optimal de l eau et de l air. Tourner la bague du jet vers la droite pour réduire le débit, ou vers la gauche l augmenter. Le cas échéant, orienter les jets pour diriger le débit d eau vers la direction désirée pour optimiser l action d hydromassage. Si désiré, éteindre le chauffe-eau en appuyant sur le bouton chauffage. Appuyer une deuxième fois sur le bouton pour redémarrer le chauffe-eau. Presser l icône de démarrage une deuxième fois pour arrêter la pompe et le chauffe-eau. REMARQUE : Votre pompe et le chauffe-eau s arrête automatiquement après environ 20 minutes de fonctionnement. Si désiré, appuyer sur l icône de démarrage pour réactiver la pompe et le chauffe-eau. Sortir doucement de la baignoire à hydromassage, et ouvrir le drain pour la vider. Effervescence Pivoter la bague extérieure jusqu à ce que l icône d effervescence clignote et appuyer sur «OK» pour activer les ports d effervescence. Le volume du débit d eau reste tel qu il a été réglé précédemment. Appuyer sur «OK» pendant que le mode effervescence clignote pour arrêter les ports d effervescence. Chromathérapie 1023275-5-C Français-5 Kohler Co.

Opération (cont.) REMARQUE : Les modes de chromathérapie peuvent être utilisés avec tous les modes d opération, même lorsque la pompe n est pas en marche. Tourner la bague extérieure pour sélectionner ce mode et appuyer sur «OK» pour activer les lumières de chromathérapie. Appuyer sur «OK» quand le mode Chromathérapie est actif pour éteindre les lumières. Tourner la bague extérieure pour sélectionner des couleurs particulières, puis appuyer sur «OK». Utiliser les flèches haut/bas pour atteindre la couleur désirée. Appuyer sur «OK» quand la sélection de couleur est active pour éteindre les lumières. Kohler Co. Français-6 1023275-5-C

Alimentation Active le mode sélectionné Augmente le débit ou la pulsation Sélection de mode Diminue le débit ou la pulsation Télécommande Fonctionnement La télécommande, dont les fonctions sont identiques à celle du clavier de l utilisateur, place les fonctions du bain à hydromassage à portée de main pour améliorer encore davantage votre expérience. La télécommande étanche est conçue pour être utilisée dans le bain, et elle flotte sur l eau. Alimentation Sélecteur Mode OK Flèche haut Flèche bas Met la baignoire à hydromassage ou le chauffe-eau en marche et les arrête. Fonctionne de la même manière que la bague extérieure sur le clavier de l utilisateur. Lorsque l on appuie, l un des modes clignote sur le clavier de l utilisateur. Si on appuie à nouveau, le mode suivant, dans le sens des aiguilles d une montre, clignote. Quand le mode désiré clignote, presser sur OK pour l activer. Active le mode désiré. Augmente le débit d eau ou l impulsion. Réduit le débit d eau ou l impulsion. Programmation REMARQUE : La programmation de la télécommande n est normalement pas requise. Il sera cependant nécessaire de programmer la télécommande par rapport au clavier de l utilisateur dans les cas suivants : (1) plus d un appareil se trouvant dans la maison ou à proximité utilise une télécommande (2) la télécommande ou la commande de la pompe est remplacée. Mettre en marche la baignoire à hydromassage. Arrêter tous les modes d opération. Attendre approximativement une minute jusqu à ce que le clavier soit complètement assombrit. (mode veille) Presser sur la flèche vers le haut du clavier, flèche vers la bas et le OK simultanément. La LED inférieure de la barre d indication du clavier de l utilisateur commence à clignoter. Quand la LED inférieure clignote, appuyer sur le bouton «OK» du clavier de l utilisateur. Une séquence de lumières s illuminera de haut en bas de la barre d indication. Pendant que la séquence de lampes est active, appuyer sur n importe quel bouton de la télécommande. Le programme se téléchargera et le clavier deviendra s assombrira. Le clavier sera maintenant compatible avec cette télécommande. Piles Dévisser le couvercle d extrémité de la télécommande, tel qu indiqué. Insérer deux piles AAA. Bien serrer le couvercle d extrémité, en s assurant que celui-ci est en contact avec le joint. 1023275-5-C Français-7 Kohler Co.