glass system technology 7
460
PANC OLTS Page 462 ROUND PULL HANDLE WTH LOCK Page 469 ROUND-SQUARE FLAT Page 473 MADE OF GLASS Page 476 STEEL Page 477 RASS OR ALUMNUM Page 480 HANDLES FOR POCKET SLDNG DOORS Page 486 HANDLES FOR SLDNG DOORS Page 487 RASS KNOS Page 491 KNOS WTH GLASS Page 493 461
PANC OLTS 462
PANC OLTS PANC OLT For panic exits it is mandatory to install systems complying with EN 1125, dedicated to systems for panic exits with devices operated by horizontal bars (traditional panic bolts and touch-bars). Devices mainly installed in rooms with public and personnel not trained for emergency procedures: cinemas, theatres, sport facilities, etc. seo Serrature has obtained the certificate of conformity with standard EN 1125:1997 + A1 :2001 number AA0003 from the Warrington Certification Limited nstitute (WCL), in order to apply the CE marking on the panic bolts, mandatory since 01/04/2003. CLASSFCATON PRNTED ON THE PRODUCT N ORDER TO DETERMNE THE APPROPRATE FEATURES FOR EACH APPLCATON. Not suitable for fire/smoke doors 3 7 6 0 1 4 2 2 A Suitable for fire/smoke doors 3 7 6 1 1 4 2 2 A Category of use Cyclical duration Door mass Fire resistance Safety for people Resistance to corrosion Safety for things ar protrusion Type of bar operation Category of use. There is a single category which envisages a very frequent use of the panic bolt by people who do not pay much attention and an accident or misuse may occur. Cyclical duration. There are two categories: grade 6 = 100.000 cycles grade 7 = 200.000 cycles Door mass. There are two categories: grade 5 = up to Kg 100, grade 6 = up to Kg 200. Fire resistance. There are two categories: grade 0 = not suitable for fire/smoke doors grade 1 = suitable for fire/smoke doors. Safety for people. There is a single category that represents the maximum achievable grade resulting from the fact that panic bolts must ensure people s safety. Resistance to corrosion. There are two categories which comply with standard UN EN1670 : 2007 grade 3 = high resistance, grade 4 = very high resistance. Safety for things. There is a single category that represents the minimum achievable degree resulting from the fact that the safety of things must be considered secondary to that of people. ar protrusion. There are two categories: grade 1 = protrusion of the bar up to mm 150 (normal) grade 2 = protrusion of the bar up to mm 100 (reduced) Type of bar operation. There are 2 categories: A = panic bolt operated by a push bar = panic bolt operated by a contact bar (Push-ar). For further details consult standard EN1125:97+ A1:2001 463
PANC OLTS The panic bolts field of application is defined by standard EN 1125 as shown below Maximum Door Width 1300 mm Maximum Door Height 2500 mm Maximum Door Weight 200 kg Operating Temperature Limits -20 C + 100 C n the event the door dimensions exceed the values indicated above, the door does no longer falls within the field of application established by standard EN 1125 and therefore the product certification is no longer valid. For doors with a mass up to 200 kg, maximum height up to 3200 mm, width up to 1500 mm, SEO declares that the performance of the handle bar are the same as those requested by the standard. Note The useful length of the bar (dimension X), must be as close as possible to the useful width (dimension Y) of the door for which it is recommended. n any case never less than 60% (see figure). For the door mass, the limit field of application remains the maximum one specified by the standard. X Y PANC OLT Material: PVD finish = internal mechanism made of AS 304 stainless steel and casing made of aluminium with PVD treatment Grey finish = internal mechanism made of galvanised steel and casing made of painted aluminium Features: panic bolt featuring material and technical solutions that allow compliance with the strictest standard requirements, among which CE marking according to directive 89/106/CEE; and voluntary product certification released by CM, as required by standard UN EN 1125. Version equipped with side latch, self-locking with exclusion option. The panic bolt may be combined in a pair with HGH/LOW bolts with rods type OLT - Art. MAP113 The bar can be shortened according to the instructions manual included in the Kit. Glass thickness with screws supplied 10/15 mm. Finish: PVD satin-finished steel, painted grey. Reversible hand Art. Description Dimensions Q.ty MAP101 Side latch + Levers + Casings L max 1285 x H 145 x D 95 mm 1 Set MAP103 Oval horizontal bar made of stainless steel L max 1130 mm 1 Pc 464 >>> PRCE LST REFERENCE PAGE 82 >>>
PANC OLTS HANDLE Material: PVD finish = internal mechanism made of galvanised steel and casing made of aluminium with PVD treatment Grey finish = internal mechanism made of galvanised steel and casing made of painted aluminium Features: handle equipped with plaque and interchangeable European cylinder, equipped with 3 keys. Finish: PVD satin-finished steel, painted grey. Art. Dimensions Q.ty MAP105 L 118 x H 124.5 x D 67.5 mm 1 Pc ELECTRCAL STRKNG PLATE Material: PVD finish = internal mechanism made of galvanised steel and casing made of aluminium with PVD treatment Grey finish = internal mechanism made of galvanised steel and casing made of painted aluminium Features: electrical striking plate. Art. MAP123 comes with the electrical striking plate in GREY FNSH ONLY; for the PVD SATN-FNSHED STEEL FNSH, order Art. MAP125 separately Finish: PVD satin-finished steel, painted grey. Art. Description Dimensions Q.ty MAP123 Electrical striking plate grey only L 38 x H 133 x D 47 mm - Electrical striking plate D = 10 mm from wall 1 Pc MAP125 Casing finish pvd satin-finished steel for electrical striking plate 1 Pc GLASS KT FOR WTHOUT EXTERNAL CONTROL Material: zamak Features: kit for mounting the panic bolt (Art. MAP101) onto glass panels, without external control (handle). Finish: PVD satin-finished steel Art. Dimensions Q.ty MAP107 H 145 x 37 mm 1 Set GLASS KT FOR WTHOUT EXTERNAL CONTROL RGHT/LEFT Material: zamak Features: kit for mounting the panic bolt (Art. MAP101) onto glass panels, with external control (handle) for right (Art. MAP109) and left external opening (Art. MAP111). Finish: PVD satin-finished steel External right Push door External left You are here You are here Art. Opening Q.ty MAP109 External right 1 Set MAP111 External left 1 Set >>> PRCE LST REFERENCE PAGE 82 >>> 465
PANC OLTS PAR OF OLTS FOR HGH/LOW CLOSNG TYPE OLT Material: aluminium casings with PVD treatment Features: bolts for high/low closing type OLT to be combined with the panic bolt (Art. MAP101) The olt system (patented) is extremely resistant to external attacks: in fact it rejects tampering (the rods are self-locking and the tips, with 14 mm diameter, are rotary and cut resistant) with high resistance to breakage. Finish: PVD satin-finished steel, painted grey. Safety and easy installation. The pins are independent, self-locking, resistant to breakage and adjustable. Self-closing system. During opening the rods stay retracted. During closing they lock when in contact with the pin receiver. Hidden floor pin receiver with dust proof system. ART. MAP127/93 Art. Dimensions Q.ty MAP113 Up to H = 2200 mm 1 Set MAP114 from H = 2200 to H = 3200 mm 1 Set GLASS KT FOR SUPPLEMENTARY LATCHES OLT Material: zamak Features: kit for installing supplementary latchestype OLT (Art. MAP113 / MAP114) Finish: PVD satin-finished steel Art. Dimensions Q.ty MAP115 H = 2200 mm 1 Set MAP116 H = 3200 mm 1 Set GLASS KT FOR SDE PN RECEVER Material: zamak Features: kit for the panic bolt side latch striking plate (Art. MAP101) Finish: PVD satin-finished steel Art. MAP117 GLASS KT FOR ADJUSTALE UPPER PN RECEVER OLT Material: zamak Features: kit for mounting the OLT upper adjustable pin receiver in presence of transom Finish: PVD satin-finished steel Art. MAP119 KT FOR STLL OPEN FUNCTON To be inserted in the ASE and OLT handle bar support to inhibit the striking plate and use the free door. Art. MAP121 Q.ty 1 Set Q.ty 1 Set Q.ty 1 Set 466 >>> PRCE LST REFERENCE PAGE 82 >>>
PANC OLTS A GLASS DRLLNG DAGRAM (internal view examples) FANLGHT FANLGHT E OLT SDE OLT SDE PULL HANDLE SDE SNGLE DOOR 3200 max D DOULE DOOR 3200 max H F D C 1030 1030 G 1300 max 1300 max 1300 max A 24 29 24 12 FANLGHT 12 min 6 R7.5 30 6 29 29 Ø15 24.5 R7.5 54 119 C 29 24 12 12 45 48 D 119 Ø15 E 48 36 min 6 12 79 24 12 24 12 F 119 Ø15 30 R7.5 R7.5 Ø15 6 79 29 29 Ø15 24.5 54 Ø15 R7.5 R7.5 119 G min 6 45 48 24 79 12 12 H Ø15 35min Ø15 119 24 12 A1 E1 29 79 12 min 6 48 39 min 6 12 min 6 48 39 39 48 48 39 X 39+X min 6 35min 12 12 24 48 36 R7.5 Ø15 R7.5 min 6 Ø15 FANLGHT 12 ARCHTRAVE ARCHTRAVE ARCHTRAVE SECTON ARCHTRAVE SECTON WTH STOP 24 24 12 FLES DWG AVALALE 467
PANC OLTS EXPLODED VEW Application Diagram (Art.) MAP-ase MAP-A MAP- MAP-C MAP-E MAP-F MAP-G MAP101 MAP101 OLT MAP101 OLT MAP101 OLT MAP101 OLT MAP101 OLT MAP101 OLT MAP103 MAP103 MAP103 MAP103 MAP103 MAP101 MAP101 MAP119 MAP117 MAP117 2 x MAP103 2 x MAP103 MAP119 MAP117 MAP117 MAP119 up to h=2200 mm MAP113 MAP113 MAP113 MAP113 MAP113 MAP113 MAP115 MAP115 MAP115 MAP115 MAP115 MAP115 from h=2200 to h=3200 mm MAP114 MAP114 MAP114 MAP114 MAP114 MAP114 MAP116 MAP116 MAP116 MAP116 MAP116 MAP116 without external control MAP107 MAP107 MAP107 MAP107 MAP107 2 x MAP107 2 x MAP107 with external control MAP105 MAP105 MAP105 MAP105 MAP105 MAP105 MAP105 MAP109 / 111 MAP109 / 111 MAP109 / 111 MAP109 / 111 MAP109 / 111 MAP109 / 111 MAP109 / 111 468 >>> PRCE LST REFERENCE PAGE 82/83 >>>
HANDLE AR 469
ROUND HANDLE AR WTH LOCK FOR GLASS DOORS ROUND SECTON Ø35 mm MADE OF AS 316L STANLESS STEEL WTH LOCK Material: AS 316 L steel Features: tubular pull handles with a patented closing system, with an unlocking cylinder on the side opposite to the latch. This allows to use the product in those particular circumstances that require a certain degree of safety. Complete with: 3 cylinder keys Fixing kit: standard Suitable for panes of variable thickness from 8 to 18 mm Standard finish: satin-finished steel - on request: polished 67 300 Ø35 Ø25 1125 75 MSG1280 Lock only 1125 67 300 Ø17 Ø35 75 GLASS HOLE 1125 75 MSG1250 Lock plus unlocking device 37 Ø16 1.5 Ø34 56.5 Ø22 Art. Diameter Length Holes centre-to-centre Q.ty MSG1280 Ø35 mm 1500 mm see diagram 1 Pair MSG1250 Ø35 mm 1500 mm see diagram 1 Pair 470 >>> PRCE LST REFERENCE PAGE 84 >>>
ROUND HANDLE AR WTH LOCK FOR GLASS DOORS PAR OF WTH PRVACY LOCK WTH ROUND SECTON Ø25 MADE OF AS 304 STEEL Material: AS 304 stainless steel Features: handle bar with lock placed on the upper end of the pipe that is closed by pressing the cylinder with the key inserted (available with different keys only). Thanks to a special internal device one prevents the cylinder from closing without its relevant key inserted. n the request one must specify if the handle bar must be equipped with a lock either on the inside or outside. Suitable for panes of variable thickness from 8 to 19 mm, the special connection is made in such a way to prevent being disassembled from the outside. Finish: satin-finished steel. on request: polished dust socket Finish: satin finish nickel. A Art. Dimensions Q.ty GARDASPL D Ø19 mm C 40 mm A Ø25 4 mm 1 Pc Art. Dimensions Pin Holes Q.ty ZSS1400 Double handle bar section Ø25 mm x length 1400 mm 572 A 128 54.5 mm Ø8 x 15 mm Ø18/20 mm 1 Pair ZMMS1400 Single handle bar section Ø25 mm x length 1400 mm 572 A 128 54.5 mm Ø8 x 15 mm Ø18/20 mm 1 Pc >>> PRCE LST REFERENCE PAGE 84 >>> 471
ROUND FOR GLASS DOORS MADE TO MEASURE PAR OF WTH ROUND SECTON Ø25 MADE OF AS 304 STEEL Material: AS 304 stainless steel Features: pull handles for glass doors with Ø25 mm round section suitable for panes of variable thickness from 8 to 19 mm. Special connection made in such a way to ease installation and prevent being disassembled from the outside. n the 1400 and 2000 mm long versions, the glass fixing connections are 3. Finish: satin-finished steel On request: polished and length made to measure A Art. Dimensions Holes Q.ty ZMT500 Section Ø25 mm x length 500 mm 300 54.5 mm Ø18/20 mm 1 Pair ZMT800 Section Ø25 mm x length 800 mm 400 54.5 mm Ø18/20 mm 1 Pair ZMT1400 Section Ø25 mm x length 1400 mm 572 A 128 54.5 mm Ø18/20 mm 1 Pair ZMT2000 Section Ø25 mm x length 2,000 mm 797 A 203 54.5 mm Ø18/20 mm 1 Pair ZMT/A Section Ø25 mm x length ON REQUEST Ø18/20 mm 1 Pair SNGLE HANDLE AR WTH ROUND SECTON Ø25 MADE OF AS 304 STEEL Material: AS 304 stainless steel Features: handle bar for glass doors with Ø25 mm round section, suitable for panes of variable thickness from 8 to 19 mm. Fixing via a flat head screw with 4 dead holes in the head. n the 1400 and 2000 mm long versions, the glass fixing connections are 3. Finish: satin-finished steel; mill finish for the screws On request: polished and length made to measure N.. UV bonding possible using Art. ZUV (Page 475) A Art. Dimensions Holes Q.ty ZST500 Section Ø25 mm x length 500 mm 300 54.5 mm Ø18/20 mm 1 Pc ZST800 Section Ø25 mm x length 800 mm 400 54.5 mm Ø18/20 mm 1 Pc ZST1400 Section Ø25 mm x length 1400 mm 572 A 128 54.5 mm Ø18/20 mm 1 Pc ZST2000 Section Ø25 mm x length 2,000 mm 797 A 203 54.5 mm Ø18/20 mm 1 Pc ZST/A Section Ø25 mm x longueur ON REQUEST Ø18/20 mm 1 Pc 472 >>> PRCE LST REFERENCE PAGE 84 >>>
SQUARE FOR GLASS DOORS MADE TO MEASURE PAR OF WTH SQUARE SECTON Ø25 MADE OF AS 304 STEEL Material: AS 304 stainless steel Features: pull handles for glass doors with 25 x 25 mm square section suitable for panes of variable thickness from 8 to 19 mm. Special connection made in such a way to ease installation and prevent being disassembled from the outside. n the 1400 mm long version, the glass fixing connections are 3. Finish: satin-finished steel On request: polished and length made to measure A Art. Dimensions Holes Q.ty ZQUA500 Section 25x25 mm x length 500 mm 300 54.5 mm Ø18/20 mm 1 Pair ZQUA800 Section 25x25 mm x length 800 mm 400 54.5 mm Ø18/20 mm 1 Pair ZQUA1400 Section 25x25 mm x length 1400 mm 572 A 128 54.5 mm Ø18/20 mm 1 Pair ZQUA/A Section 25x25 mm x longueur ON REQUEST Ø18/20 mm 1 Pair SNGLE HANDLE AR WTH SQUARE SECTON 25x25 MADE OF AS 304 STEEL Material: AS 304 stainless steel Features: handle bar for glass doors with 25 x 25 mm square tubular section, suitable for panes of variable thickness from 8 to 19 mm. Fixing via a flat head screw with 4 dead holes in the head. Finish: satin-finished steel; mill finish for the screws On request: polished and length made to measure N.. UV bonding possible using Art. ZUV (Page 475) A Art. Dimensions Holes Q.ty ZSQ500 Section 25x25 mm x length 500 mm 300 54.5 mm Ø18/20 mm 1 Pc ZSQ800 Section 25x25 mm x length 800 mm 400 54.5 mm Ø18/20 mm 1 Pc ZSQ1400 Section 25x25 mm x length 1400 mm 572 A 128 54.5 mm Ø18/20 mm 1 Pc ZSQ/A Section 25x25 mm x longueur ON REQUEST Ø18/20 mm 1 Pc >>> PRCE LST REFERENCE PAGE 84 >>> 473
FLAT FOR GLASS DOORS MADE TO MEASURE PAR OF FLAT SECTON 35x10 MADE OF STEEL AS 304 Material: AS 304 stainless steel Features: pull handles for glass doors with 35x10 mm flat solid section, suitable for panes of variable thickness from 8 to 19 mm. Special connection made in such a way to ease installation and prevent being disassembled from the outside Finish: satin-finished steel On request: polished steel and length made to measure Art. Dimensions Holes Q.ty ZP500 Section 35x10 mm x length 500 mm 300 54.5 mm Ø18/20 mm 1 Pair ZP800 Section 35x10 mm x length 800 mm 400 54.5 mm Ø18/20 mm 1 Pair ZP/A Section 35x10 mm x longueur ON REQUEST Ø18/20 mm 1 Pair SNGLE HANDLE AR WTH FLAT SECTON 35x10 MADE OF AS 304 STEEL Material: AS 304 stainless steel Features: handle bar for glass doors with 35x10 mm flat solid section, round section Ø25 mm, suitable for panes of variable thickness from 8 to 19 mm. Fixing via a flat head screw with 4 dead holes in the head. Finish: satin-finished steel; mill finish for the screws On request: polished steel and length made to measure N.. UV bonding possible using Art. ZUV (Page 475) Art. Dimensions Holes Q.ty ZSP500 Section 35x10 mm x length 500 mm 300 54.5 mm Ø18/20 mm 1 Pc ZSP800 Section 35x10 mm x length 800 mm 400 54.5 mm Ø18/20 mm 1 Pc ZSP/A Section 35x10 mm x longueur ON REQUEST Ø18/20 mm 1 Pc 474 >>> PRCE LST REFERENCE PAGE 85 >>>
HANDLE AR ATTACCHMENT FOR SNGLE (Series: ZST / ZSQ / ZSP) FOR UV RAYS APPLCATON Material: AS 304 stainless steel Accessory Ø35 for pull handles to be applied without drilling the glass, via UV ray glue bonding. t is recommended to glue the supports with the handle bar models already mounted Colour: mill finish D C A Art. Dimensions Q.ty ZUV A Ø35 mm 27.5 mm C 4.5 mm D Ø14.5 mm 1 Pc FLAT FXNG FOR PAR Material: AS 304 stainless steel Finish: stainless steel S = 8/27 mm 5 38 Ø35 Ø22.5 M6 Ø15 1 M12 4 M6 Example with Art. COFS15 Example with Art. ORC25 Art Dimensions Holes Q.ty ZATT Ø35 x 43+43 mm Ø18 mm 1 Pc >>> PRCE LST REFERENCE PAGE 85 >>> 475
MADE OF GLASS PAR OF GLASS ROUND SECTON Ø25 Material: optical glass glued onto AS 304 stainless steel connections Features: optical glass pull handles for glass doors with Ø25 mm round section length 500 / 800 / 1400 mm suitable for panes of variable thickness from 6 to 12 mm. Special connection made in such a way to ease installation and prevent being disassembled from the outside. n the 1400 mm long version, the glass fixing connections are 3. Glass finish: satin-finished or transparent - Connection finish: satin-finished steel A Art. Dimensions Holes Q.ty SH500 Section Ø25 mm x length 500 mm 300 52 mm Ø13 mm 1 Pair SH800 Section Ø25 mm x length 800 mm 400 52 mm Ø13 mm 1 Pair SH1400 Section Ø25 mm x length 1400 mm 572 A 128 52 mm Ø13 mm 1 Pair 476 >>> PRCE LST REFERENCE PAGE 85 >>>
HANDLE AR 477
A STEEL PAR OF HANDLES 300 mm x Ø16 / Ø20 mm Material: AS 304 steel Features: pull handles for glass doors with round section for glass up to 12 mm. For greater thicknesses simply replace the internal countersunk screws. Finish: polished steel or satin-finished steel C S Art. Dimensions Holes Glass Q.ty MN1620 C Ø16 mm A 300 mm 200 mm minimum Ø12 mm S 6/12 mm 1 Pair MN2020 C Ø20 mm A 300 mm 200 mm minimum Ø12 mm S 6/12 mm 1 Pair PAR OF ROUND Ø25 MADE OF STEEL Material: AS 304 stainless steel Features: pull handles for glass doors with Ø25 mm round section suitable for panes of variable thickness from 6 to 12 mm. Finish: polished steel or satin-finished steel C S A Art. Dimensions Holes Glass Q.ty MN25300 C Ø25 mm A 300 mm 200 mm minimum Ø12 mm S 6/12 mm 1 Pair MN25400 C Ø25 mm A 400 mm 250 mm minimum Ø12 mm S 6/12 mm 1 Pair MN25500 C Ø25 mm A 500 mm 300 mm minimum Ø14 mm S 6/12 mm 1 Pair MN25800 C Ø25 mm A 800 mm 400 mm minimum Ø14 mm S 6/12 mm 1 Pair 478 >>> PRCE LST REFERENCE PAGE 85 >>>
A STEEL PAR OF ROUND Ø25 mm MADE OF STEEL Material: AS 304 stainless steel Features: pull handles for glass doors with round section for glass up to 12 mm. For greater thicknesses simply replace the internal countersunk screws. Finish: polished steel or satin-finished steel C S Art. Dimensions Holes Glass Q.ty MN25850 C Ø25 mm A 850 mm 650 mm minimum Ø12 mm S 6/12 mm 1 Pair MN251200 C Ø25 mm A 1200 mm 1040 mm minimum Ø12 mm S 6/12 mm 1 Pair PAR OF ROUND Ø25 mm MADE OF STEEL WTH SDE GRP Material: AS 304 stainless steel Features: pull handles for glass doors with Ø25 mm round section AND SDE GRP suitable for panes of variable thickness from 10 to 12 mm. Finish: polished steel or satin-finished steel Art. Dimensions Glass Holes Q.ty MN32800 Section Ø25 mm x length 800 mm 400 72.5 mm 10/12 Ø14 mm 1 Pair >>> PRCE LST REFERENCE PAGE 85/86 >>> 479
RASS OR ALUMNUM PAR OF HANDLES Ø14 MM Material: brass or aluminium Features: extruded brass or aluminium, depending on the type of finish. Connection formed by 2 cylindrical connectors, to which the handles will be fixed. An M5 threaded bar allows to fix the handles to any thickness. Suitable, as well as for fixing on glass, also on sliding systems with aluminium profile. Contact surface on the structure Ø13 mm. n the case of a larger hole, it is recommended to use the washer to increase the support surface Art. PM4. Grip distance: 20 mm Glass: 6 / 8 mm - 10 / 12 mm with Art. PM4 Finish: chrome, satin finish nickel, matt aluminium Application example on EKU profile Art PM4 Description 4 Washers for increasing the support surface Dimensions Ø18 / Ø13.2x3 mm Q.ty 1 Set Finish: polished chrome, satin nickel finish Art. Dimensions Glass hole Hole on metal Q.ty PM1 Ø14 mm Height 460 mm Centre-to-centre 320 mm minimum 6 mm Ø5.5 mm 1 Pair PM2 Ø14 mm Height 310 mm Centre-to-centre 224 mm minimum 6 mm Ø5.5 mm 1 Pair PM3 Ø14 mm Height 200 mm Centre-to-centre 128 mm minimum 6 mm Ø5.5 mm 1 Pair 480 >>> PRCE LST REFERENCE PAGE 86 >>>
ALUMNUM 15x15mm HANDLE ARS Material: aluminum Features: 2 connectors fix the handles. An M4 threaded bar allows the handles to work on any thickness. They are also suitable for sliding systems with aluminum profiles. Grip distance: 23mm Glass: 6/12mm Finish: Matt aluminum, polished, satin steel L A LM320 LM224 LM128 Art. Dimensions Glass hole Glass Q.ty LM320 15 x15 mm L 460 mm A 320 mm 23 mm Ø 12 mm 6 / 12 mm 1 Pair LM224 15 x15 mm L 310 mm A 224 mm 23 mm Ø 12 mm 6 / 12 mm 1 Pair LM128 15 x15 mm L 200 mm A 128 mm 23 mm Ø 12 mm 6 / 12 mm 1 Pair >>> PRCE LST REFERENCE PAGE 86 >>> 481
ZNC ALLOY HANDLE 1340 Material: zinc alloy Features: pair of handles with fixing screws M5 Grip distance: 40 mm Center-to-center holes: 380 mm Finish: chrome, stainless steel effect 50 M5 S 50 20 Ø10 50 50 400 380 10 40 40 10 380 380 20 M5 20 Ø10 Art. Dimensions Holes Glass Q.ty PMAN1340 L 400 x H 50 x 20 mm Ø 10 mm 6/10 mm 1 Pair 482 >>> PRCE LST REFERENCE PAGE 86 >>>
ALUMNUM HANDLE 404 FOR SLDNG SYSTEMS WTH VH FXNG Material: aluminum Features: no drilling, welding or extra finishing required. Excellent sealing proprieties with vibration absorption and compensation of various expansion coefficients of the materials - it maintains its endurance unaltered - UV and chemical detergent resistant - t reduces assembling costs since does not require professionals. Finish: Matt aluminum, polished aluminum Ø 15 20 27.5 35 Art. Dimensions Q.ty MAN404V160 L 230 x P 27,5 mm 1 Pc MAN404V320 L 380 x P 27,5 mm 1 Pc MAN404V448 L 530 x P 27,5 mm 1 Pc >>> PRCE LST REFERENCE PAGE 87 >>> 483
ALUMNUM HANDLE 408 FOR SLDNG SYSTEMS WTH VH FXNG Material: aluminum Features: no drilling, welding or extra finishing required. Excellent sealing proprieties with vibration absorption and compensation of various expansion coefficients of the materials - it maintains its endurance unaltered - UV and chemical detergent resistant - t reduces assembling costs since does not require professionals. Finish: Matt aluminum, polished aluminum 17.5 9 Art. Dimensions Q.ty MAN408V160 L 260 x P 17,5 mm 1 Pc MAN408V320 L 410 x P 17,5 mm 1 Pc MAN408V448 L 560 x P 17,5 mm 1 Pc SURFACES PREPARATON n order to obtain a perfect bonding, it is important for the area where the handle will be connected, to be cleaned with the included wipe, than let it dry at room temperature (minimum 21 C maximum 38C). Epthane or alcohol and water can be used as cleaning solvents. Once you have peeled off the protective film, apply a firm pressure between the handle and the support. 90% of the tightness is reached after one day, with a definite adjustment after 72 hours. n order to increase the bonding in wet areas it is necessary to heat the room at 70 C per about an hour. Clean with detergent dry with wipe peeled the protective film and apply apply firm pressure 484 >>> PRCE LST REFERENCE PAGE 87 >>>
HANDLES FOR SLDNG DOORS 485
HANDLES FOR POCKET SLDNG DOORS HANDLES FOR POCKET SLDNG DOORS Material: brass Features: cast brass body, mechanically processed remaining parts. New square handle design for pocket sliding doors, with hook mechanism to facilitate opening. Finish: chrome, imitation satin steel, imitation matt aluminium 58 R11 100 Ø22 64 78 86 58 Ø22 R11 76 Art. Dimensions Glass Q.ty MSC7 H 100 mm L 76 mm 8/10 mm 1 Pc HANDLES FOR SLDNG DOORS Material: brass Features: cast brass body, mechanically processed remaining parts. New square handle design for sliding doors. Finish: chrome, imitation satin steel, imitation matt aluminium 58 R11 100 Ø22 64 78 86 58 Ø22 R11 76 Art. Dimensions Glass Q.ty MSC5 H 100 mm L 76 mm 8/10 mm 1 Pc 486 >>> PRCE LST REFERENCE PAGE 87 >>>
HANDLES FOR SLDNG DOORS HANDLES FOR SLDNG SYSTEMS 6036 Material: Aluminum Features: Aluminum Ø 60 mm pair of handles. A Ø 38 mm hole is necessary for the mounting. Finish: Matt aluminum, polished aluminum, stainless steel effect aluminum 10 Ø42 Ø60 Art. Dimensions Glass Glass hole Q.ty MAL6036 Ø 60 mm 8/10/12 mm Ø 38 mm 1 Pair HANDLES FOR SLDNG SYSTEMS 6050 Material: Aluminum Features: Aluminum Ø 60 mm pair of handles. A Ø 51 mm hole is necessary for the mounting. Finish: Matt aluminum, polished aluminum, stainless steel effect aluminum 7 Ø50 Ø60 Art. Dimensions Glass Glass hole Q.ty MAL6050 Ø 60 mm 8/10/12 mm Ø 51 mm 1 Pair >>> PRCE LST REFERENCE PAGE 87 >>> 487
HANDLES FOR SLDNG DOORS PAR OF ROUND HANDLES Ø60 Material: AS 304 steel Features: pair of handles made of AS 304 stainless steel with Ø60 mm round section, with a hidden central component required for mounting the glass Glass thickness: 8/12 mm Ring grip: 10 mm Finish: mill finish Optional: 2 gaskets Art. GT235 made of die-cut PVC to replace those present if needed Art. Dimensions Hole Q.ty MAT60 Ø60 mm Height 12 mm Grip 10 mm Ø14 mm 1 Pair PAR OF SQUARE HANDLES 60x60 Material: AS 304 steel Features: pair of handles made of AS 304 stainless steel with 60x60 mm square section, with a hidden central component required for mounting the glass and OR to facilitate alignment Glass thickness: 8/12 mm Ring grip: 10 mm Finish: mill finish Art. Dimensions Hole Q.ty MAQ60 60x60 mm Height 12 mm Grip 10 mm Ø14 mm 1 Pair 488 >>> PRCE LST REFERENCE PAGE 87 >>>
PAR OF ROUND HANDLES Ø40 Material: AS 304 steel Features: pair of handles made of AS 304 stainless steel with Ø40 mm round section and gaskets supplied Glass thickness: 8/12 mm Ring grip: 6 mm Finish: mill finish HANDLES FOR SLDNG DOORS Art. Dimensions Hole Q.ty MAT40 Ø40 mm Height 8 mm Grip 6 mm Ø30 mm 1 Pair PAR OF SQUARE HANDLES 40x40 Material: AS 304 steel Features: pair of handles made of AS 304 stainless steel with square section, 40 mm side and OR gaskets to facilitate alignment Glass thickness: 8/12 mm Ring grip: 6 mm Finish: mill finish Art. Dimensions Hole Q.ty MAQ40 40x40 mm Height 8 mm Grip 6 mm Ø30 mm 1 Pair ROUND HANDLE Ø40 SNGLE Material: AS 304 steel Features: handle made of AS 304 stainless steel with Ø40 mm round section, which can be applied to the glass via UV bonding or with glues suitable for metal and glass bonding Ring grip: 6 mm Finish: mill finish Art. Dimensions Q.ty MAUVT40 Ø40 mm Height 8 mm Grip 6 mm 1 Pc SQUARE HANDLE 40x40 SNGLE Material: AS 304 steel Features: handle made of AS 304 stainless steel with 40 mm square section, which can be applied to the glass via UV bonding or with glues suitable for metal and glass bonding Ring grip: 6 mm Finish: mill finish Art. Dimensions Pack MAUVQ40 40x40 mm Height 8 mm Grip 6 mm 1 Pc >>> PRCE LST REFERENCE PAGE 87/88 >>> 489
HANDLES FOR SLDNG DOORS HANDLE 83 Material : AS 304 stainless steel Finish: polished steel, satin steel 7 Ø63 Ø38 50 S MAT8314 MAT8320 Art. Dimensions Hole Glass Q.ty MAT8314 Ø 63 mm - OPEN Ø 50 mm 6/10 mm 1 Pc MAT8320 Ø 63 mm - CLOSE Ø 50 mm 6/10 mm 1 Pc ROUND HANDLE WTH GRP Material: brass Features: pair of Ø60 mm handles with grip. Finish: polished chrome, satin nickel finish Art. Dimensions Glass hole Q.ty MSC9 Ø 60 mm Ø 50 mm 1 Pair RNGS FOR SLDNG DOORS 60 Material: brass Open or closed version nternal grip Ø38 mm Finish: chrome, gold, matt nickel Ø55 mm Art. Dimensions Glass hole Glass Q.ty MAN60A Ø 60x10 ins. Ø38 mm - OPEN Ø 55 mm 8/12 mm 1 Pc MAN60C Ø 60x10 ins. Ø38 mm - CLOSE Ø 55 mm 8/12 mm 1 Pc 490 >>> PRCE LST REFERENCE PAGE 88 >>>
RASS KNOS PAR OF RASS KNOS Ø45x35 mm Material: brass, solid bar processing Finish: chrome, satin nickel finish S 36 Ø38.5 Ø45 3.25 Ø8 Art Dimensions Minimum hole Glass Q.ty POM4535 2 x Ø45 x 35 mm 8 mm 8/19 1 Pair PAR OF CYLNDRCAL RASS KNOS Ø35 X 50 mm Material: brass, solid bar processing Finish: chrome, gold, satin nickel finish S 51 Ø35 2 Ø10 Art. Overall dimensions For glass Minimum hole Q.ty VETCL35 2 x Ø35 x 50 mm x M8 8/12 mm 10 mm 1 Pair >>> PRCE LST REFERENCE PAGE 88 >>> 491
RASS KNOS PAR OF KNOS FOR DOORS SERES 180 Material: brass - Features: pair of knobs Ø70 or 50 to be applied, as well as on the glass, via the special kit included in the pack of each knob, even on wooden doors. Suitable for all glass thicknesses Finish: chrome, matt nickel, P.V.D. gold S A Ø18 Ø 7 Ø6 Accessory for mounting a pair (supplied) Art. Dimensions Hole Q.ty POM18070 Section dimensions Ø70 mm A 100 mm Ø6 mm minimum 1 Pair POM18050 Section dimensions Ø50 mm A 74 mm Ø6 mm minimum 1 Pair PAR OF KNOS FOR DOORS SERES 181 Material: brass - Features: pair of knobs Ø75 or 50 to be applied, as well as on the glass, via the special kit included in the pack of each knob, even on wooden doors. Suitable for all glass thicknesses Finish: chrome, matt nickel, P.V.D. gold S A Ø18 Ø 7 Ø6 Accessory for mounting a pair (supplied) Art. Dimensions Hole Q.ty POM18170 Section dimensions Ø75 mm A 70 mm Ø6 mm minimum 1 Pair POM18150 Section dimensions Ø50 mm A 55 mm Ø6 mm minimum 1 Pair 492 >>> PRCE LST REFERENCE PAGE 88/89 >>>
KNOS WTH GLASS COMPRESSED KNOS Ø75 FOR GLASS DOORS Material: glass glued onto brass base Glass colour: satin-finished ase finish: chrome, gold, satin-finished nickel Art. Overall knob dimensions ase For glass Hole Q.ty POM75 Ø75 x 55 mm x M8 Ø30 mm 8/12 mm minimum 10 mm 1 Pair KNOS Ø65 FOR GLASS DOORS Material: glass glued onto brass base Glass colour: transparent with bubbles, transparent, satin-finished, transparent coloured and satin-finished coloured ase finish: chrome, gold, satin nickel finish Art. Overall knob dimensions ase For glass Hole Q.ty POM65 Ø65 x 88 mm x M8 Ø30 mm 8/12 mm minimum 10 mm 1 Pair KNOS SERES ARUS 905 Ø40/55 mm Material: glass glued onto brass base Glass colour: transparent, satin-finished ase finish: chrome, gold Art. Overall dimensions ase Hole Q.ty POM90540 Ø40 x 57 mm x M4 Ø29 mm minimum 5 mm 1 Pc POM90555 Ø55 x 78 mm x M6 Ø41 mm minimum 7 mm 1 Pc >>> PRCE LST REFERENCE PAGE 89 >>> 493