INTERNATIONAL STANDARD NORME INTERNATIONALE

Size: px
Start display at page:

Download "INTERNATIONAL STANDARD NORME INTERNATIONALE"

Transcription

1 IEC Edition INTERNATIONAL STANDARD NORME INTERNATIONALE Optical fibres Part 1-44: Measurement methods and test procedures Cut-off wavelength Fibres optiques Partie 1-44: Méthodes de mesure et procédures d'essai Longueur d onde de coupure INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE PRICE CODE CODE PRIX S ICS ISBN Registered trademark of the International Electrotechnical Commission Marque déposée de la Commission Electrotechnique Internationale

2 IEC:2011 CONTENTS FOREWORD Scope Normative references Background Overview of methods Mapping functions Reference test method Apparatus Light source Modulation Launch optics Support and positioning apparatus Cladding mode stripper Deployment mandrel General Cable cut-off wavelength, Method A Cable cut-off wavelength, Method B Fibre cut-off wavelength, Method C Detection optics Detector assembly and signal detection electronics Sampling and specimens Specimen length Specimen end face Procedure Positioning of specimen in apparatus General requirements for all methods Deployment requirements for each method Measurement of output power Overview Bend-reference technique Multimode-reference technique Calculations Bend-reference technique Multimode-reference technique Curve-fitting technique for improved precision (optional) General Step 1, define the upper-wavelength region Step 2, characterize the attenuation curve Step 3, determine the upper wavelength of the transition region Step 4, determine the lower wavelength of the transition region Step 5, characterize the transition region with the theoretical model Step 6, compute the cut-off wavelength, λ c Results Report the following information with each measurement: The following information shall be available upon request:... 17

3 IEC: Specification information Annex A (normative) Requirements specific to method A Cable cut-off wavelength, λ cc, using uncabled fibre Annex B (normative) Requirements specific to method B Cable cut-off wavelength, λ cc, using cabled fibre Annex C (normative) Requirements specific to method C Fibre cut-off wavelength, λ c Bibliography Figure 1 Deployment configuration for cable cut-off wavelength, method A... 9 Figure 2 Deployment configuration for cable cut-off wavelength, method B Figure 3 Default configuration to measure λ c Figure 4 Deployment configurations for fibre cut-off measurement Figure 5 Cut-off wavelength using the bend-reference technique Figure 6 Cut-off wavelength using the multimode-reference technique... 13

4 IEC:2011 INTERNATIONAL ELECTROTECHNICAL COMMISSION OPTICAL FIBRES Part 1-44: Measurement methods and test procedures Cut-off wavelength FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as IEC Publication(s) ). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC has been prepared by subcommittee 86A: Fibres and cables, of IEC technical committee 86: Fibre optics. This second edition cancels and replaces the first edition published in This edition constitutes a technical revision. The main change with respect to the previous edition is the withdrawal of Annex D. Annexes A, B and C form an integral part of this standard. This standard should be read in conjunction with IEC

5 IEC: This bilingual edition corresponds to the monolingual English version, published in The text of this standard is based on the following documents: FDIS 86A/1369/FDIS Report on voting 86A/1385/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC x series, published under the general title Optical fibres Measurement methods and test procedures, can be found on the IEC website The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under " in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended.

6 IEC:2011 OPTICAL FIBRES Part 1-44: Measurement methods and test procedures Cut-off wavelength 1 Scope This part of IEC establishes uniform requirements for measuring the cut-off wavelength of single-mode optical fibre, thereby assisting in the inspection of fibres and cables for commercial purposes. This standard gives the methods for measuring the cut-off wavelength of fibre and cable There are two methods for measuring cable cut-off wavelength, λ cc : Method A: using uncabled fibre; Method B: using cabled fibre. There is only one method (Method C) for measuring fibre cut-off wavelength, λ c. The test method in this standard describes procedures for determining the cut-off wavelength of a sample fibre in either an uncabled condition (λ c ) or in a cable (λ cc ). Three default configurations are given here: any different configuration will be given in a detail specification. These procedures apply to all category B and C fibre types (see Normative references). All methods require a reference measurement. There are two reference-scan techniques, either or both of which may be used with all methods: bend-reference technique; multimode-reference technique using category A1 multimode fibre. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC , Optical fibres Part 1-1: Measurement methods and test procedures General and guidance IEC , Optical fibres Part 1-40: Measurement methods and test procedures Attenuation

7 CEI:2011 SOMMAIRE AVANT-PROPOS Domaine d application Références normatives Contexte Vue d'ensemble des méthodes Fonctions de cartographie Méthode d'essai de référence Appareillage Source lumineuse Modulation Dispositif optique d'injection Appareillage de maintien et de positionnement Extracteur des modes de gaine Mandrin de déploiement Généralités Longueur d'onde de coupure de câble, Méthode A Longueur d'onde de coupure de câble, Méthode B Longueur d'onde de coupure de fibre, Méthode C Dispositif optique de détection Ensemble détecteur et dispositif électronique de détection des signaux Echantillonnage et spécimens Longueur du spécimen Face d'extrémité du spécimen Procédure Positionnement du spécimen dans l'appareillage Exigences générales pour toutes les méthodes Exigences spécifiques au déploiement pour chaque méthode Mesure de la puissance de sortie Aperçu Technique de la fibre de référence courbée Technique de la fibre de référence multimodale Calculs Technique de la fibre de référence courbée Technique de la fibre de référence multimodale Technique d'ajustement de courbe pour augmenter la précision (optionnel) Généralités Etape 1, définir la zone des longueurs d'ondes supérieures Etape 2, caractériser la courbe d affaiblissement Etape 3, déterminer la plus grande longueur d'onde de la zone de transition Etape 4, déterminer la plus petite longueur d'onde de la zone de transition Etape 5, caractériser la zone de transition à l'aide du modèle théorique Etape 6, calcul de la longueur d'onde de coupure, λ c Résultats... 40

8 CEI: Relever les informations suivantes pour chaque mesure: Les informations suivantes doivent être disponibles sur demande: Informations à mentionner dans la spécification Annexe A (normative) Exigences spécifiques à la méthode A Longueur d'onde de coupure de câble, λ cc, en utilisant la fibre non câblée Annexe B (normative) Exigences spécifiques à la méthode B Longueur d'onde de coupure de câble, λ cc, en utilisant la fibre câblée Annexe C (normative) Exigences spécifiques à la méthode C Longueur d'onde de coupure de fibre, λ c Bibliographie Figure 1 Configuration relative au déploiement pour la mesure de la longueur d'onde de coupure de câble, méthode A Figure 2 Configuration relative au déploiement pour la mesure de la longueur d'onde de coupure de câble, méthode B Figure 3 Configuration par défaut pour mesurer λ c Figure 4 Configurations de déploiement pour la mesure de la longueur d'onde de coupure de la fibre Figure 5 Longueur d'onde de coupure par la technique de la fibre de référence courbée Figure 6 Longueur d'onde de coupure par la technique de la fibre de référence multimodale... 35

9 CEI:2011 COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE FIBRES OPTIQUES Partie 1-44: Méthodes de mesure et procédures d'essai Longueur d onde de coupure AVANT-PROPOS 1) La Commission Electrotechnique Internationale (CEI) est une organisation mondiale de normalisation composée de l'ensemble des comités électrotechniques nationaux (Comités nationaux de la CEI). La CEI a pour objet de favoriser la coopération internationale pour toutes les questions de normalisation dans les domaines de l'électricité et de l'électronique. A cet effet, la CEI entre autres activités publie des Normes internationales, des Spécifications techniques, des Rapports techniques, des Spécifications accessibles au public (PAS) et des Guides (ci-après dénommés "Publication(s) de la CEI"). Leur élaboration est confiée à des comités d'études, aux travaux desquels tout Comité national intéressé par le sujet traité peut participer. Les organisations internationales, gouvernementales et non gouvernementales, en liaison avec la CEI, participent également aux travaux. La CEI collabore étroitement avec l'organisation Internationale de Normalisation (ISO), selon des conditions fixées par accord entre les deux organisations. 2) Les décisions ou accords officiels de la CEI concernant les questions techniques représentent, dans la mesure du possible, un accord international sur les sujets étudiés, étant donné que les Comités nationaux de la CEI intéressés sont représentés dans chaque comité d études. 3) Les Publications de la CEI se présentent sous la forme de recommandations internationales et sont agréées comme telles par les Comités nationaux de la CEI. Tous les efforts raisonnables sont entrepris afin que la CEI s'assure de l'exactitude du contenu technique de ses publications; la CEI ne peut pas être tenue responsable de l'éventuelle mauvaise utilisation ou interprétation qui en est faite par un quelconque utilisateur final. 4) Dans le but d'encourager l'uniformité internationale, les Comités nationaux de la CEI s'engagent, dans toute la mesure possible, à appliquer de façon transparente les Publications de la CEI dans leurs publications nationales et régionales. Toutes divergences entre toutes Publications de la CEI et toutes publications nationales ou régionales correspondantes doivent être indiquées en termes clairs dans ces dernières. 5) La CEI elle-même ne fournit aucune attestation de conformité. Des organismes de certification indépendants fournissent des services d'évaluation de conformité et, dans certains secteurs, accèdent aux marques de conformité de la CEI. La CEI n'est responsable d'aucun des services effectués par les organismes de certification indépendants. 6) Tous les utilisateurs doivent s'assurer qu'ils sont en possession de la dernière édition de cette publication. 7) Aucune responsabilité ne doit être imputée à la CEI, à ses administrateurs, employés, auxiliaires ou mandataires, y compris ses experts particuliers et les membres de ses comités d'études et des Comités nationaux de la CEI, pour tout préjudice causé en cas de dommages corporels et matériels, ou de tout autre dommage de quelque nature que ce soit, directe ou indirecte, ou pour supporter les coûts (y compris les frais de justice) et les dépenses découlant de la publication ou de l'utilisation de cette Publication de la CEI ou de toute autre Publication de la CEI, ou au crédit qui lui est accordé. 8) L'attention est attirée sur les références normatives citées dans cette publication. L'utilisation de publications référencées est obligatoire pour une application correcte de la présente publication. 9) L attention est attirée sur le fait que certains des éléments de la présente Publication de la CEI peuvent faire l objet de droits de brevet. La CEI ne saurait être tenue pour responsable de ne pas avoir identifié de tels droits de brevets et de ne pas avoir signalé leur existence. La Norme internationale CEI a été établie par le sous-comité 86A: Fibres et câbles, du comité d'études 86 de la CEI: Fibres optiques. Cette deuxième édition annule et remplace la première édition parue en Elle constitue une révision technique. La principale modification par rapport à l édition précédente consiste en la suppression de l Annexe D. Les Annexes A, B et C font partie intégrante de la présente norme. Il convient de lire la présente norme conjointement avec la CEI

10 CEI: La présente version bilingue correspond à la version anglaise monolingue publiée en Le texte anglais de cette norme est issu des documents 86A/1369/FDIS et 86A/1385/RVD. Le rapport de vote 86A/1385/RVD donne toute information ayant abouti à l approbation de cette norme. La version française de cette norme n a pas été soumise au vote. Cette publication a été rédigée selon les Directives ISO/CEI, Partie 2. Une liste de toutes les parties de la série CEI x, publiées sous le titre général Fibres optiques Méthodes de mesure et procédures d essai, est disponible sur le site internet de la CEI. Le comité a décidé que le contenu de cette publication ne sera pas modifié avant la date de stabilité indiquée sur le site web de la CEI sous " dans les données relatives à la publication recherchée. A cette date, la publication sera reconduite, supprimée, remplacée par une édition révisée, ou amendée.

11 CEI:2011 FIBRES OPTIQUES Partie 1-44: Méthodes de mesure et procédures d'essai Longueur d onde de coupure 1 Domaine d application La présente partie de la CEI établit des exigences uniformes pour mesurer la longueur d'onde de coupure des fibres optiques unimodales, contribuant ainsi au contrôle des fibres et câbles dans des relations commerciales. La présente norme donne les méthodes de mesure de la longueur d onde de coupure de fibre et de câble. Il existe deux méthodes pour mesurer la longueur d'onde de coupure de câble, λ cc : Méthode A: en utilisant la fibre non câblée; Méthode B: en utilisant la fibre câblée. Il n'existe qu'une méthode (Méthode C) pour mesurer la longueur d'onde de coupure de fibre, λ c. La méthode d essai de la présente norme décrit les procédures pour déterminer la longueur d'onde de coupure d'un échantillon de fibre soit à l'état non câblée (λ c ), soit dans un câble (λ cc ). Trois configurations par défaut sont données ici: toute configuration différente sera indiquée dans la spécification particulière. Ces procédures s appliquent à tous les types de fibres de catégories B et C (voir Références normatives). Toutes les méthodes prescrivent une mesure de référence. Il y a deux techniques d exploration de référence, l'une et/ou l'autre peuvent être utilisées avec toutes les méthodes: technique de la fibre de référence courbée; technique de la fibre de référence multimodale utilisant la fibre multimodale de catégorie A1. 2 Références normatives Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les références datées, seule l édition citée s applique. Pour les références non datées, la dernière édition du document de référence s'applique (y compris les éventuels amendements). IEC , Optical fibres Part 1-1: Measurement methods and test procedures General and guidance (disponible uniquement en anglais) CEI : Fibres optiques Partie 1-40: Méthodes de mesure et procédures d essai Affaiblissement

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61314-1-1 Edition 3.0 2011-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Fibre optic fan-outs Part 1-1: Blank detail specification Dispositifs

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60811-504 Edition 1.0 2012-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric and optical fibre cables Test methods for non-metallic materials Part 504: Mechanical tests Bending tests at low temperature

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60811-508 Edition 1.0 2012-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric and optical fibre cables Test methods for non-metallic materials Part 508: Mechanical tests Pressure test at high

More information

TECHNICAL SPECIFICATION SPÉCIFICATION TECHNIQUE

TECHNICAL SPECIFICATION SPÉCIFICATION TECHNIQUE IEC/TS 62282-1 Edition 2.0 2010-04 TECHNICAL SPECIFICATION SPÉCIFICATION TECHNIQUE Fuel cell technologies Part 1: Terminology Technologies des piles à combustible Partie 1: Terminologie INTERNATIONAL ELECTROTECHNICAL

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61935-2-20 Edition 1.0 2008-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Testing of balanced communication cabling in accordance with ISO/IEC 11801 Part 2-20: Patch cords and work area cords Blank

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60811-501 Edition 1.0 2012-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric and optical fibre cables Test methods for non-metallic materials Part 501: Mechanical tests Tests for determining

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60811-401 Edition 1.0 2012-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric and optical fibre cables Test methods for non-metallic materials Part 401: Miscellaneous tests Thermal ageing methods

More information

TECHNICAL REPORT RAPPORT TECHNIQUE

TECHNICAL REPORT RAPPORT TECHNIQUE TECHNICAL REPORT RAPPORT TECHNIQUE IEC/TR 61508-0 Edition 1.0 2005-01 Functional safety of electrical/electronic/programmable electronic safety-related systems Part 0: Functional safety and IEC 61508 Sécurité

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 62568 Edition 1.0 2015-07 colour inside Overhead lines Method for fatigue testing of conductors Lignes aériennes Méthode d'essai de fatigue des conducteurs

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 62137-1-2 Edition 1.0 2007-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Surface mounting technology Environmental and endurance test methods for surface mount solder joint Part 1-2: Shear strength

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60216-3 Edition 2.0 2006-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Electrical insulating materials Thermal endurance properties Part 3: Instructions for calculating thermal endurance characteristics

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61169-35 Edition 1.0 2011-07 INTERNATIONAL STANDARD NORME INTERNATIONALE colour inside Radio-frequency connectors Part 35: Sectional specification for 2,92 series RF connectors Connecteurs pour fréquences

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60749-21 Edition 2.0 2011-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Semiconductor devices Mechanical and climatic test methods Part 21: Solderability Dispositifs à semiconducteur Méthodes d essai

More information

TECHNICAL SPECIFICATION SPÉCIFICATION TECHNIQUE

TECHNICAL SPECIFICATION SPÉCIFICATION TECHNIQUE IEC/TS 62282-1 Edition 3.0 2013-11 TECHNICAL SPECIFICATION SPÉCIFICATION TECHNIQUE Fuel cell technologies Part 1: Terminology Technologies des piles à combustible Partie 1: Terminologie INTERNATIONAL ELECTROTECHNICAL

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60745-2-1 Edition 2.1 2008-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Hand-held motor-operated electric tools Safety Outils électroportatifs à moteur Sécurité Partie 2-1: Règles particulières pour

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60086-3 INTERNATIONAL STANDARD NORME INTERNATIONALE Edition 3.0 2011-01 Primary batteries Part 3: Watch batteries Piles électriques Partie 3: Piles pour montres INTERNATIONAL ELECTROTECHNICAL COMMISSION

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60127-2 Edition 2.2 2010-08 Miniature fuses Part 2: Cartridge fuse-links Coupe-circuit miniatures Partie 2: Cartouches INTERNATIONAL ELECTROTECHNICAL COMMISSION

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 62056-9-7 Edition 1.0 2013-04 INTERNATIONAL STANDARD NORME INTERNATIONALE colour inside Electricity metering data exchange The DLMS/COSEM suite Part 9-7: Communication profile for TCP-UDP/IP networks

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61439-5 Edition 1.0 2010-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Low-voltage switchgear and controlgear assemblies Part 5: Assemblies for power distribution in public networks Ensembles d'appareillage

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60754-2 Edition 2.0 2011-11 INTERNATIONAL STANDARD NORME INTERNATIONALE GROUP SAFETY PUBLICATION PUBLICATION GROUPÉE DE SÉCURITÉ Test on gases evolved during combustion of materials from cables Part

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 62031 Edition 1.1 2012-10 colour inside LED modules for general lighting Safety specifications Modules de DEL pour éclairage général Spécifications de sécurité

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC CEI 60846-2 First edition Première édition 2007-07 Radiation protection instrumentation Ambient and/or directional dose equivalent (rate) meters and/or monitors

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60502-4 Edition 2.0 2005-02 Power cables with extruded insulation and their accessories for rated voltages from 1 kv (U m = 1,2 kv) up to 30 kv (U m = 36

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60947-7-2 Edition 3.0 2009-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Low-voltage switchgear and controlgear Part 7-2: Ancillary equipment Protective conductor terminal blocks for copper conductors

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60050-351 Edition 4.0 2013-11 INTERNATIONAL STANDARD NORME INTERNATIONALE HORIZONTAL STANDARD NORME HORIZONTALE International electrotechnical vocabulary Part 351: Control technology Vocabulaire électrotechnique

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61730-2 Edition 1.1 2012-11 colour inside Photovoltaic (PV) module safety qualification Part 2: Requirements for testing Qualification pour la sûreté de

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 62337 Edition 2.0 2012-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Commissioning of electrical, instrumentation and control systems in the process industry Specific phases and milestones Mise en

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 62625-2 Edition 1.0 2016-01 colour inside Electronic railway equipment On board driving data recording system Part 2: Conformity testing Matériel électronique

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61076-4-113 Edition 1.0 2002-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Connectors for electronic equipment Printed board connectors Part 4-113: Detail specification for two-part connectors having

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60507 Edition 3.0 2013-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems Essais sous pollution artificielle

More information

PUBLICLY AVAILABLE SPECIFICATION PRE-STANDARD

PUBLICLY AVAILABLE SPECIFICATION PRE-STANDARD IEC/PAS 62396-5 PUBLICLY AVAILABLE SPECIFICATION PRE-STANDARD Edition 1.0 2007-09 Process management for avionics Atmospheric radiation effects Part 5: Guidelines for assessing thermal neutron fluxes and

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61784-5-16 Edition 1.0 2013-09 INTERNATIONAL STANDARD NORME INTERNATIONALE colour inside Industrial communication networks Profiles Part 5-16: Installation of fieldbuses Installation profiles for CPF

More information

CONSOLIDATED VERSION VERSION CONSOLIDÉE

CONSOLIDATED VERSION VERSION CONSOLIDÉE CONSOLIDATED VERSION VERSION CONSOLIDÉE IEC 62554 Edition 1.1 2017-10 colour inside Sample preparation for measurement of mercury level in fluorescent lamps Préparation des échantillons en vue de la mesure

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60730-2-9 Edition 3.0 2008-06 Automatic electrical controls for household and similar use Part 2-9: Particular requirements for temperature sensing controls

More information

CONSOLIDATED VERSION VERSION CONSOLIDÉE

CONSOLIDATED VERSION VERSION CONSOLIDÉE CONSOLIDATED VERSION VERSION CONSOLIDÉE IEC 60311 Edition 4.2 2009-06 colour inside Electric irons for household or similar use Methods for measuring performance Fers à repasser électriques pour usage

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61970-552 Edition 2.0 2016-09 colour inside Energy management system application program interface (EMS-API) Part 552: CIMXML Model exchange format Interface

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60599 Edition 3.0 2015-09 Mineral oil-filled electrical equipment in service Guidance on the interpretation of dissolved and free gases analysis Matériels

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60358-1 Edition 1.0 2012-06 INTERNATIONAL STANDARD NORME INTERNATIONALE colour inside Coupling capacitors and capacitor dividers Part 1: General rules Condensateurs de couplage et diviseurs capacitifs

More information

INTERNATIONAL STANDARD

INTERNATIONAL STANDARD INTERNATIONAL STANDARD IEC 62396-1 Edition 1.0 2012-05 colour inside Process management for avionics Atmospheric radiation effects Part 1: Accommodation of atmospheric radiation effects via single event

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 62264-2 Edition 2.0 2013-06 INTERNATIONAL STANDARD NORME INTERNATIONALE colour inside Enterprise-control system integration Part 2: Objects and attributes for enterprise-control system integration

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 62271-204 Edition 1.0 2011-07 High-voltage switchgear and controlgear Part 204: Rigid gas-insulated transmission lines for rated voltage above 52 kv Appareillage

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61508-4 Edition 1.0 1998-12 BASIC SAFETY PUBLICATION PUBLICATION FONDAMENTALE DE SÉCURITÉ Functional safety of electrical/electronic/programmable electronic

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60335-2-56 INTERNATIONAL STANDARD NORME INTERNATIONALE Edition 3.1 2008-07 Household and similar electrical appliances Safety Part 2-56: Particular requirements for projectors and similar appliances

More information

CONSOLIDATED VERSION VERSION CONSOLIDÉE

CONSOLIDATED VERSION VERSION CONSOLIDÉE CONSOLIDATED VERSION VERSION CONSOLIDÉE IEC 60601-2-41 Edition 2.1 2013-10 colour inside Medical electrical equipment Part 2-41: Particular requirements for the basic safety and essential performance of

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 62364 Edition 1.0 2013-06 INTERNATIONAL STANDARD NORME INTERNATIONALE colour inside Hydraulic machines Guide for dealing with hydro-abrasive erosion in Kaplan, Francis, and Pelton turbines Machines

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC/IEEE 62704-3 Edition 1.0 2017-10 colour inside Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communications

More information

Dangerous Goods Handling and Règlement sur la manutention et le transport

Dangerous Goods Handling and Règlement sur la manutention et le transport THE DANGEROUS GOODS HANDLING AND TRANSPORTATION ACT (C.C.S.M. c. D12) LOI SUR LA MANUTENTION ET LE TRANSPORT DES MARCHANDISES DANGEREUSES (c. D12 de la C.P.L.M.) Dangerous Goods Handling and Règlement

More information

HOLA SAFETY RING PLAN

HOLA SAFETY RING PLAN FRENCH VERSION ON PAGE 3 HOLA SAFETY RING PLAN PRICE: $50.00 per person EFFECTIVE FEBRUARY 01, 2019 The Hola Safety Ring Plan allows you to cancel your trip with a refund up to 3 days before departure

More information

ISO INTERNATIONAL STANDARD. Non-invasive sphygmomanometers Part 1: Requirements and test methods for non-automated measurement type

ISO INTERNATIONAL STANDARD. Non-invasive sphygmomanometers Part 1: Requirements and test methods for non-automated measurement type INTERNATIONAL STANDARD ISO 81060-1 First edition 2007-12-01 Non-invasive sphygmomanometers Part 1: Requirements and test methods for non-automated measurement type Sphygmomanomètres non invasifs Partie

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61158-4-24 Edition 1.0 2014-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial communication networks Fieldbus specifications Part 4-24: Data-link layer protocol specification Type 24 elements

More information

GUIDE D INSTALLATION PVC CELLULAIRE

GUIDE D INSTALLATION PVC CELLULAIRE GUIDE D INSTALLATION PVC CELLULAIRE 7 5 3 4 1 2 6 8 NOTES IMPORTANTES Travailler toujours de gauche à droite, de bas en haut. Utiliser des vis en acier inoxidable #8 x 1.5 (3,8 cm) à tous les 16 /40,64

More information

SCADE for AIRBUS critical avionics systems

SCADE for AIRBUS critical avionics systems SCADE Users Conference October 2009 Presented by Jean-Charles DALBIN Airbus Operations SAS SCADE for AIRBUS critical avionics systems Scade Users Conference 2009 Agenda Airbus Context SCADE use Automatic

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61784-5-2 Edition 3.0 2013-09 INTERNATIONAL STANDARD NORME INTERNATIONALE colour inside Industrial communication networks Profiles Part 5-2: Installation of fieldbuses Installation profiles for CPF

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60947-2 Edition 4.2 2013-01 colour inside Low-voltage switchgear and controlgear Part 2: Circuit-breakers Appareillage à basse tension Partie 2: Disjoncteurs

More information

PRE-RELEASE VERSION (FDIS)

PRE-RELEASE VERSION (FDIS) IEC 61375-2-6 Edition 1.0 2018-02 PRE-RELEASE VERSION (FDIS) colour inside Electronic railway equipment Train communication network (TCN) Part 2-6: On-board to ground communication Matériel électronique

More information

INTERNATIONAL STANDARD NORME INTERNATIONALE

INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 60076-1 Edition 2.1 2000-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Power transformers Part 1: General Transformateurs de puissance Partie 1: Généralités INTERNATIONAL ELECTROTECHNICAL COMMISSION

More information

Roll Up 28. Ref A. DE Anleitung FR Notice ES Manual PT Instruções PL Instrukcja RU Руководство CS Návod

Roll Up 28. Ref A. DE Anleitung FR Notice ES Manual PT Instruções PL Instrukcja RU Руководство CS Návod Roll Up 28 WT Ref. 5122117A DE Anleitung FR Notice ES Manual PT Instruções PL Instrukcja RU Руководство CS Návod Copyright 2013 Somfy SAS. All rights reserved - V1-02/2013 1 Sommaire 1. Informations préalables

More information

TECHNICAL SPECIFICATION

TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION IEC TS 62396-1 First edition 2006-03 Process management for avionics Atmospheric radiation effects Part 1: Accommodation of atmospheric radiation effects via single event effects

More information

1. Configurez votre Stick Up Cam Wired dans l application Ring.

1. Configurez votre Stick Up Cam Wired dans l application Ring. Stick Up Cam Wired 1. Configurez votre Stick Up Cam Wired dans l application Ring. Téléchargez l application Ring. L application vous guide dans la configuration et l utilisation de votre Stick Up Cam

More information

This document is a preview generated by EVS

This document is a preview generated by EVS EESTI STANDARD EVS-EN 61558-2-9:2003 Jõutrafode, elektri edastusseadmete ja muude taoliste toodete ohutus. Osa 2-9: Erinõuded III klassi hõõglampkäsivalgustite trafodele Safety of power transformers, power

More information

This document is a preview generated by EVS

This document is a preview generated by EVS INTERNATIONAL STANDARD ISO 5912 Fourth edition 2011-10-01 Camping tents Tentes de camping Reference number ISO 5912:2011(E) ISO 2011 ISO 2011 COPYRIGHT PROTECTED DOCUMENT All rights reserved. Unless otherwise

More information

I lf:,jo ~ S-o 3S9~75"97. ARRETE NO. Z lOZ. BY-LAW NO. Z lOZ. A by-law amending Zoning By-Law Z of the Town of Shediac

I lf:,jo ~ S-o 3S9~7597. ARRETE NO. Z lOZ. BY-LAW NO. Z lOZ. A by-law amending Zoning By-Law Z of the Town of Shediac BY-LAW NO. Z-14-44-lOZ A by-law amending Zoning By-Law Z-14-44 of the Town of Shediac WHEREAS the Council of the Town of Shediac has determined that it is in the public interest to amend the Zoning By

More information

ISO INTERNATIONAL STANDARD. Protective clothing Aprons, trousers and vests protecting against cuts and stabs by hand knives

ISO INTERNATIONAL STANDARD. Protective clothing Aprons, trousers and vests protecting against cuts and stabs by hand knives INTERNATIONAL STANDARD ISO 13998 First edition 2003-01-15 Protective clothing Aprons, trousers and vests protecting against cuts and stabs by hand knives Vêtements de protection Tabliers, pantalons et

More information

BANQUE DE DONNEES MINIERES DU GROUPE DES ETATS ACP

BANQUE DE DONNEES MINIERES DU GROUPE DES ETATS ACP BANQUE DE DONNEES MINIERES DU GROUPE DES ETATS ACP 4 de la base de données Toutes les informations sont stockées dans une base de données et peuvent être mises à jour. Le présent site Internet n est pas

More information

INTERNATIONAL STANDARD

INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 5912 Fourth edition 2011-10-01 Camping tents Tentes de camping Reference number ISO 5912:2011(E) ISO 2011 ISO 2011 COPYRIGHT PROTECTED DOCUMENT All rights reserved. Unless otherwise

More information

Index. RainBlade 1970

Index. RainBlade 1970 Interior glazed, full rainscreen design with bull nose profile Vitrer de l'intérieur avec écran pare pluie et profilé avec un nez Index Primary components Composantes principales Thermal Simulation chart

More information

GENE-AUTO Status of new Airbus case Studies

GENE-AUTO Status of new Airbus case Studies GENEAUTO 9/29/2009 Presented by Jean-Charles DALBIN Airbus Operations SAS & Laurent DUFFAU Airbus Operations SAS GENE-AUTO Status of new Airbus case Studies Airbus Operation SAS - GENEAUTO Status on Airbus

More information

ISO Rubber and plastics hoses and hose assemblies Vocabulary. Tuyaux et flexibles en caoutchouc et en plastique Vocabulaire

ISO Rubber and plastics hoses and hose assemblies Vocabulary. Tuyaux et flexibles en caoutchouc et en plastique Vocabulaire Provläsningsexemplar / Preview INTERNATIONAL STANDARD NORME INTERNATIONALE ISO 8330 Third edition Troisième édition 2014-08-15 Rubber and plastics hoses and hose assemblies Vocabulary Tuyaux et flexibles

More information

I We reserve the right to modify or attar Instructions. No modification or

I We reserve the right to modify or attar Instructions. No modification or INSTALLATION INSTRUCTION VLFS3265 Floor Stand TV Mobile Cart For TV panels: 32"-65" Maximum load capacity: 100 lbs/ 45.5 kg AV shelf max load: 10 lbs/ 4.5 kg Video tray max load: 10 lbs/ 4.5 kg VESA: 100x100-600x400mm

More information

Développement d Application & interface Web-BDD

Développement d Application & interface Web-BDD Développement d Application & interface Web-BDD - Final Internship Defense - Master2 Computer Sciences Dpt. Mathematics & Computer Sciences Univeristy of La Réunion 23 juin 2015 1 / 25 Toward the university

More information

Programmation Mobile Android Master CCI

Programmation Mobile Android Master CCI Programmation Mobile Android Master CCI Bertrand Estellon Aix-Marseille Université March 23, 2015 Bertrand Estellon (AMU) Android Master CCI March 23, 2015 1 / 266 Les fragments Un fragment : représente

More information

Index. TerraPorte 7600 & accessable

Index. TerraPorte 7600 & accessable TerraPorte 7600 & accessable Out-Swing / Ouverture Extérieure Thermally broken frame with superior air / water performance. Rain screen design and multi-point locking ideal for residential and condominium

More information

Le Tour Du Monde En 80 Jours (French Edition) By Jules Verne

Le Tour Du Monde En 80 Jours (French Edition) By Jules Verne Le Tour Du Monde En 80 Jours (French Edition) By Jules Verne Le Tour du monde en 80 jours. Couverture En vérité, ne ferait-on pas, pour moins que cela, le tour du monde? Le texte amazon.fr Voir la by VERNE

More information

RT2N Thermostat compact

RT2N Thermostat compact aractéristiques Excellente répétabilité Réglage de l'écart pour la régulation orrection de l'écart pour le contrôle et l'alarme Résistant à la surpression accidentelle Léger pplications Équipement de sécurité

More information

SOUTH AFRICAN NATIONAL STANDARD

SOUTH AFRICAN NATIONAL STANDARD ISBN 978-0-626-25095-9 IEC 60601-2-52:2009 SOUTH AFRICAN NATIONAL STANDARD Medical electrical equipment Part 2-52: Particular requirements for the basic safety and essential performance of medical beds

More information

1. Information générale 1. General information

1. Information générale 1. General information Rapport d'activités des CN 2012 2012 Activity Report of NCs RÉSUMÉ SUMMARY Article / Question Item / Question Svp, écrivez votre texte ici Please, enter your text here 1. Information générale 1. General

More information

Thermographie, pourquoi l utiliser?

Thermographie, pourquoi l utiliser? Thermographie, pourquoi l utiliser? Manny Alsaid FLIR Systems Jacques Wagner MultiPro Plus = 3,600 Thermomètre IR Thermometre IR La zone de mesure Distance au cible Ce quoi l infrarouge? Voir la réalité

More information

ThermaWall XTRM2600 Unitized Curtain Wall

ThermaWall XTRM2600 Unitized Curtain Wall ThermaWall XTRM2600 Unitized Curtain Wall Unitized thermally broken curtain wall - Capped and SSG, 2 1/2" (63.5mm) and 3" (76.2mm) profile widths, various system depths. Mur-rideau à bris thermique unitisé

More information

1. CANADA DAY 2012 PARKING LOT PARTIES IN THE BYWARD MARKET FÊTE DU CANADA 2012 CÉLÉBRATIONS TENUES DANS LE PARC DE STATIONNEMENT DU MARCHÉ BY

1. CANADA DAY 2012 PARKING LOT PARTIES IN THE BYWARD MARKET FÊTE DU CANADA 2012 CÉLÉBRATIONS TENUES DANS LE PARC DE STATIONNEMENT DU MARCHÉ BY 1 COMITÉ DES TRANSPORTS 1. CANADA DAY 2012 PARKING LOT PARTIES IN THE BYWARD MARKET FÊTE DU CANADA 2012 CÉLÉBRATIONS TENUES DANS LE PARC DE STATIONNEMENT DU MARCHÉ BY COMMITTEE RECOMMENDATIONS That Council

More information

Rapport d'activités des CN 2006 Activity Report Form 2006

Rapport d'activités des CN 2006 Activity Report Form 2006 Rapport d'activités des CN 2006 Activity Report Form 2006 RÉSUMÉ SUMMARY Article / Question Item / Question Svp, écrivez votre texte ici Please, enter your text here 1. Information générale 1. General

More information

ISO/IEC INTERNATIONAL STANDARD NORME INTERNATIONALE. Information technology Openedi reference model

ISO/IEC INTERNATIONAL STANDARD NORME INTERNATIONALE. Information technology Openedi reference model INTERNATIONAL STANDARD NORME INTERNATIONALE ISO/IEC 14662 Third edition Troisième édition 2010-02-15 Information technology Openedi reference model Technologies de l'information Modèle de référence EDI-ouvert

More information

Manuel des statuts et règlements du Comité de liaison UMCE.

Manuel des statuts et règlements du Comité de liaison UMCE. Manuel des statuts et règlements du UMCE. Révisé le 22 juin 2016 TABLES DES MATIÈRES Chapitre 1 Préambule..... 1 Chapitre 2 DÉFINITIONS..... 1 2.01 Employé....... 1.01 Catégories d emplois à l UMCE......

More information

Part 1: Oil-based fluid applications

Part 1: Oil-based fluid applications SVENSK STANDARD SS-ISO 1436-1 Fastställd 2001-09-28 Utgåva 1 Slang och slangledningar av gummi Hydraulslang med flätad stålarmering Krav Del 1: För oljebaserade vätskor Rubber hoses and hose assemblies

More information

VISALE PROCEDURE. How to apply for a visa with "visale.fr"? Mars 2019

VISALE PROCEDURE. How to apply for a visa with visale.fr? Mars 2019 VISALE PROCEDURE How to apply for a visa with "visale.fr"? Mars 2019 INFOS: o VISALE is free. o You must subscribe to VISALE if you are between 18 and 30 years old. o VISALE is open to foreign students

More information

Charter and Governance Framework of the International Land Coalition

Charter and Governance Framework of the International Land Coalition Charter and Governance Framework of the International Land Coalition Charte et Cadre de Gouvernance de la Coalition internationale pour l accès à la terre Carta y Marco Rector de la Coalición Internacional

More information

Rapport d'activités des CN 2007 Activity Report Form 2007

Rapport d'activités des CN 2007 Activity Report Form 2007 Rapport d'activités des CN 2007 Activity Report Form 2007 RÉSUMÉ SUMMARY Article / Question Item / Question Svp, écrivez votre texte ici Please, enter your text here 1. Information générale 1. General

More information

ISO Graphical symbols Safety colours and safety signs Registered safety signs AMENDMENT 1

ISO Graphical symbols Safety colours and safety signs Registered safety signs AMENDMENT 1 INTERNATIONAL STANDARD ISO 7010 Second edition 2011-06-01 AMENDMENT 1 2012-04-15 Graphical symbols Safety colours and safety signs Registered safety signs AMENDMENT 1 Symboles graphiques Couleurs de sécurité

More information

RAPPORT DE TEST DE / TEST REPPORT BY. 01-mars-12. BOYER Marc. Date MODELE / MODEL DIAMIR MARQUE / MANUFACTORY NERVURES

RAPPORT DE TEST DE / TEST REPPORT BY. 01-mars-12. BOYER Marc. Date MODELE / MODEL DIAMIR MARQUE / MANUFACTORY NERVURES RPPORT DE TEST DE / TEST REPPORT BY BOYER Marc Date 01-mars-12 MRQUE / MNUFCTORY NERVURES MODELE / MODEL DIMIR Procédure Poids min / min PTV 70 kg TILLE /SIZE S HRNIS SUP IR weight EVO XC2 TYPE abs VENTRLE

More information

ESPACE DES ONG / NGO SPACE 39 e session de la Conférence générale / 39 th session of the General Conference

ESPACE DES ONG / NGO SPACE 39 e session de la Conférence générale / 39 th session of the General Conference ESPACE DES ONG / NGO SPACE 39 e session de la Conférence générale / 39 th session of the General Conference Programme provisoire des activités / Preliminary Programme of Activities (ce programme est sujet

More information

THE WORLD IS YOURS. Formations linguistiques & interculturelles

THE WORLD IS YOURS. Formations linguistiques & interculturelles THE WORLD IS YOURS Formations linguistiques & interculturelles 11 langues, plus de 160 cultures et de nombreuses thématiques managériales dans nos centres tout confort, au cœur de l Europe Un apprentissage

More information

Kakinada (Cocanada) bay (Andhra Pradesh-E India)

Kakinada (Cocanada) bay (Andhra Pradesh-E India) Sea - Seek Ebook Sailing guide / Guide nautique Kakinada (Cocanada) bay (Andhra Pradesh-E India) Indian Ocean - Bay of Bengal - East Coast of India November 2018 http://www.sea-seek.com November 2018 Kakinada

More information

STANDING COMMITTEE ON THE FOOD CHAIN AND ANIMAL HEALTH Section Animal Health and Welfare

STANDING COMMITTEE ON THE FOOD CHAIN AND ANIMAL HEALTH Section Animal Health and Welfare STANDING COMMITTEE ON THE FOOD CHAIN AND ANIMAL HEALTH Section Animal Health and Welfare COMITÉ PERMANENT DE LA CHAÎNE ALIMENTAIRE ET DE LA SANTÉ ANIMALE Section Santé Animale et Bien-être des animaux

More information

00 Page du titre Frontpage Contenu du dossier List of drawings. 02 Localisation du site Site location. Implantation. 04 Vue en plan Top view

00 Page du titre Frontpage Contenu du dossier List of drawings. 02 Localisation du site Site location. Implantation. 04 Vue en plan Top view 00 Page du titre Frontpage Contenu du dossier List of drawings 0 Note technique faisabilite Technical note feasability 02 Localisation du site Site location 03a Implantation Implantation 04 Vue en plan

More information

INS #Shaper IL525013N WARNING WARNING WARNING WARNING WARNING

INS #Shaper IL525013N WARNING WARNING WARNING WARNING WARNING IL525013N INS #Shaper Make Certain Power is OFF before starting installation or attempting any maintenance. Risk of Fire/Electric Shock. If not qualified, consult an electrician. Risk of Electric Shock

More information

ISO INTERNATIONAL STANDARD. Non-invasive sphygmomanometers Part 2: Clinical validation of automated measurement type

ISO INTERNATIONAL STANDARD. Non-invasive sphygmomanometers Part 2: Clinical validation of automated measurement type INTERNATIONAL STANDARD ISO 81060-2 First edition 2009-05-01 Non-invasive sphygmomanometers Part 2: Clinical validation of automated measurement type Sphygmomanomètres non invasifs Partie 2: Validation

More information

Organisation de Coopération et de Développement Économiques Organisation for Economic Co-operation and Development

Organisation de Coopération et de Développement Économiques Organisation for Economic Co-operation and Development Non classifié/unclassified EXD/CSD/W(2017)13 EXD/CSD/W(2017)13 Non classifié/unclassified Organisation de Coopération et de Développement Économiques Organisation for Economic Co-operation and Development

More information

Index. TerraPorte 7600 & accessable

Index. TerraPorte 7600 & accessable TerraPorte 7600 & accessable Out-Swing / Ouverture Extérieure Thermally broken frame with superior air / water performance. Rain screen design and multi-point locking ideal for residential and condominium

More information

WELCOME TO ALL OUR VOLVO S AMATEURS FRIENDS

WELCOME TO ALL OUR VOLVO S AMATEURS FRIENDS WELCOME TO ALL OUR VOLVO S AMATEURS FRIENDS For the first time since its creation, this 9th IVM will take place in France. Through this opportunity the Volvo Club of France who is getting settling this

More information

CONVOCATION The Westin Zagreb Krsnjavoga 1 Zagreb, CROATIA : (385) (1) : (385) (1)

CONVOCATION The Westin Zagreb Krsnjavoga 1 Zagreb, CROATIA : (385) (1) : (385) (1) CONVOCATION Your Federation is called to participate to the Annual General Congress of the ESF, at : Votre Fédération est appelée à participer au Congrès Général Annuel de l ESF, à : The Westin Zagreb

More information