Compass Home 8' x 8' No Tools Gazebo with Awning and Anchor Bags Assembly Instruction for Gazebo (no tools required)

Size: px

Start display at page:

Download "Compass Home 8' x 8' No Tools Gazebo with Awning and Anchor Bags Assembly Instruction for Gazebo (no tools required)"

Buddy Newton
5 years ago
Views:

1 Compass Home 8' x 8' No Tools Gazebo with Awning and Anchor Bags Assembly Instruction for Gazebo (no tools required) CAUTION: Read all instructions before assembly. Failure to do so may result in faulty assembly and potential injury. Two people are recommended for assembly of the gazebo. Read all the instructions before assembly and use of this gazebo. 1. Select ideal location to avoid moving item after assembly. 2. Do not use knife in order to prevent scratching the surface. 3. Use caution during assembly especially when lifting heavy or bulky parts. Do not allow bystanders into work area. 4. Check all parts. Before assembling, make sure that you have all parts described in the parts list. 5. Keep children away. Children are prohibited in the work area during assembly. 6. It is also highly recommended to remove the gazebo top during inclement or stormy weather. 7. NOT RECOMMENDED for use during stormy conditions. Damage can occur to your gazebo and put you and others in potential danger. 8. Always use the provided stakes to secure your gazebo to the ground unless you set up on concrete or asphalt. 9. Do not use your gazebo for permanent shelter, it was designed for temporary use only. 10. Do not allow any one to climb on the gazebo. CLEANING & CARE: Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. ATTENTION: To avoid damage, remove the cover during bad weather, e.g. during high winds or heavy rains. 1 year warranty Test Rite International Co., Ltd. warrants the original purchaser that this Gazebo shall be free of defects in material or workmanship for a period of 1-year from the original date of purchase. In the event of a defect in material or workmanship of this product within 1-year from the original date of purchase, the purchaser may contact American Customer Service at for replacement parts. This warranty covers defects in manufacturing discovered while using the product as recommended by the manufacturer.the warranty does not cover loss or theft, nor does coverage extend to damage caused by misuse; abuse; unauthorized repair or alteration; incidental or alteration; incidental or consequential damages; accident; natural disaster or other circumstances not directly attributable or material defects.

2 PARTS LIST NO. PART DESCRIPTION DIAGRAM Q TY 1 Roof Support 4 2 Roof Support Extension 4 3 Short bar 4 4 Right lintel 4 5 Left lintel 4 6 Upper post 4 7 Lower post 4 8 Center Connector 1 9 Upper lintel connector 4 10 Lower lintel connector 4 11 Awning right tube 1 12 Awning left tube 1 13 Awning Support tube 2 14 Hook 4 15 Stake 8 16 Small Canopy 1 17 Canopy 1 18 Awning Fabric 1 19 Anchor Bag 4

3 Assembly Steps: Step 1: Insert the right lintel (4) into the hole of the upper post(6) and slide into the slot, then insert the left lintel (5) into the upper post(6) and slide into the slot. Repeat this step for all four sets. Insert the Roof Support Extension(2) into the hole of the upper post (6). You will hear a "click" when the button is pushed in place and the tube is fixed in the post. Repeat this step for all four sets. Step 2: Attach the right lintel (4) to the left lintel (5) with upper and Lower lintel connector (9 & 10). Make sure the bracket on the upper lintel is facing up. Repeat this step for all four sets, refer to the diagram below. Step 3: Attach roof support (1) and short Bar (3) to the center connector (8). Insert the roof support (1) into the roof support extension (2) that was previously assembled in step 1. Insert short bar (3) into the upper lintel connector (9),slide the pin(14) throught and insert the clip into the hole.

4 Step 4: Insert the awning left tube (12) into the upper post (6). Repeat to assemble the right tube (11). To easily align the joint on the awning tube (11 & 12) and upper post (6), make sure the awning tube (11 & 12) is parallel with the upper post (6). The long bar on the awning tube (11/12) will attach to the top bracket of the upper post (6) and the short bar will attach to the bottom bracket. Step 5: Make sure large canopy slides under the small canopy section to create the two tier look. Stretch the small canopy cover (16) over the top small bars of each roof support (1) to form the small top section of the gazebo. Stretch the large canopy cover (17) to the four corners of the roof support extensions (2) and end of short bars (3) to form the main top of the gazebo. Step 6: Once the canopy section is secured, insert the upper post (6) into the lower post (7) by sliding the stud in the upper post (6) into the groove in the Lower post (7) and turn the lower post (7) counter-clockwise to lock. Next, add the awning fabric(18) onto the awning frame by inserting the awning support tubes (13) into the sleeves of the awning fabric (18), slide the outer most support tube onto outer most peg located on each awning tube. Next, slide the inner support tube to inner peg located on each awning tube, snap buttons along awning tubes (12 & 11) and gazebo frame. Fix the gazebo to the ground by inserting the stake(15) into the hole of the base of the pole post (7). If you wish to make the gazebo more secure, or have on a hard surface where stakes cannot be used, fix the anchor bags filled with sand to each gazebo. Now your gazebo is ready for use. Put sand into the bag,close up the bag,then put the sandbag around the post and fasten.

6 Option steps: 1: The awning tube is adjustable. If only half an awning is required, simply press the pin lock on the awning tube (11/12) and push the lower side into upper. If full awning is required, pull out each the tube gradually until both push buttons lock. 2: The awning tubes (11/12) are moveable, and can assemble on any side you want. To create a side wall with the awning, simply press in both push buttons on the awning tubes (11/12) closest to the gazebo posts and slide the awning down until flush with gazebo posts. Secure the wall to the gazebo by attaching each long strap located on each side of the awning to the posts of the gazebo. The full drawing below is for your reference.

LM601 Landmark Permanent Blind

LM601 Landmark Permanent Blind Get parts online at www.huntriversedge.com P/N: 26742 REV1: 01/13/17 2017 RETI All Rights Reserved INTRODUCTION Landmark Permanent Blinds are engineered with you the hunter