Atlas HO M&StL Decorated RS1 Detailing Project
|
|
- Barnard Bradford
- 5 years ago
- Views:
Transcription
1 Atlas HO M&StL Decorated RS1 Detailing Project There are a several modifications needed to give the Atlas factory decorated units true M&StL personality. I will go through the most noticeable modifications in photos and text. Feel free to do only the steps you are comfortable with. What are the most noticeable additions needed to give this model M&StL personality? Obviously the steam bell, marker lights and unique cab all-weather windows are the most noticeable. Not so obvious is the relocation of the hood top front exhaust vent walkway, the awning over the engineer s side air intake vent, and square cab vent. We ll start this detailing project with the hood front top exhaust vent. When the railroad installed the steam engine bells it was apparent that the walkways protecting the louvers would have to be moved. They were repositioned from the center to along the engineer s side of the opening. Figure 1 On the older Atlas RS1s the walkway was pressed in place and will snap off. On the newer offerings the walkways are glued in place and will need to be cut off. Use a Xacto knife with a #17 blade to chisel off the walkway. Do both ends, and then slide the blade in under the sides to cut the pegs under the grating portion of the walkway. Fill and sand the four places in the hood where the walkway was attached.
2 Figure 2 This photo shows where the attachment pegs are located. Figure 3 With the walkway removed there is now a depression in the center of the louvers. File off all the louvers until you have a flat surface. There is a convex protrusion across the front of the vent frame. This is there to aid in molding and can be filed off if desired to make the entire vent housing square.
3 Figure 4 Figure 5 These two photos show a flat surface for adding new louvers and the walkway glued to the outer edge of the vent. The mounting legs at the corners of the grating will need to be snipped to the correct length. I did not remove the extra material from the front of the vent housing. If I had I would have had to shorten the walkway.
4 Figure 6 The louver opening perimeter frame is made of.010x.030 styrene strip. The rounded front of the housing is quite obvious in this photo. Figure 7 10 pieces of.010x.030 styrene strip were used to represent the open louvers.
5 Figure 8 Holes were drilled into the sides of the sand hatches and the marker lights added. Cal-Scale # Marker Lites, Loco & Tender Figure 9 A 1/16 hole was drilled in the hood and the bell was added. The 1/16 hole is too large. I used gel type ACC to affix the bell, the larger hole allows for adjustment to center the bell and the gel type ACC filled the voids. Bell is by Cal-Scale #BE-328 Bell w/anti rotation top bar
6 Figure 10 The model has a round cab vent; the M&StL units had square vents. Use a narrow file to remove the round cab vent. Replace with a piece of styrene. I used.040x.156 strip cut square (.156x.156x.040 ). My vent looks a bit too tall. Maybe.020 or.030 thick styrene strip might look better. Figure 11
7 Figure 12 I painted my vent with Polly Scale SP lettering gray with a drop of Polly Scale ATSF blue added. Figure 13 The side intake louvers opened when the engine coolant reached a certain temperature. A canvas cover was placed over the engineer s side louver opening to aid in better temperature control during winter months. The canvas sheet slid on a rod that ran across the top of the opening (like a shower curtain). To protect the canvas and rod an awning was fabricated over the top of the rod. I simulated an awning with.015x.060 styrene strip. Two short pieces were glued to the ends at an angle.
8 Figure 14 Spur nippers were used to snip off the small end pieces even with the long awning section. Figure 15 The awning has been glued in place and covered with a piece of decal stripe. The awnings were painted to match each particular unit. Consult photos if you are modeling a different unit for the correct color.
9 Figure 16 The M&StL designed a unique side window extension to protect their crewmen during inclement weather. We call them all-weather windows or something similar. These windows could be disassembled during the summer months. The window box ends were left attached to the cab sides and could be used as wind deflectors while running at mainline speeds. Etched brass all-weather windows in HO scale can be purchased from Joe Binish. Follow the bending instructions included. These will need to be painted to match the particular unit you re modeling. I painted mine with the gray/blue mix mentioned previously, and a mix of Polly Scale ATSF blue with a few drops of Badger Accuflex C&NW dark green and a dab of Polly Scale SP lettering gray. These were colors I had on hand. Try as you will, I can guarantee you will not match the manufacturers paint. Just try to get close. I used yellow decal stripping from my decal scrap box. The windows were airbrushed with Floquil Flat Finish to seal the decal stripes. The clear finish darkened the blue and gray paint. Paint mixes for anything requiring clear coats should be mixed lighter than the color you want to match to compensate for the darkening effect of the clear coats.
10 Figure 17 Engineer s cab window. Figure 18 Firemen s cab window.
11 Figure 19 Figure 20 I used flush cutting pliers to remove most of the bell casting attached to the model s underframe. A motor tool would do a better job. The bare metal was painted with Floquil Grimy black.
12 Figure 21 Figure 22 The prototype units had a small plow under the coupler and between the foot boards. I simulated these with a portion of an EMD pilot part available for Proto 2000 GP, SD models. I also replaced the stock couplers with Kadee.
13 Figure 23 Finished model, engineer s side. I added the rolled up canvas that was used to cover the intake louvers during cold weather. I rolled a single ply of facial tissue around a small diameter wire, painted it with Polly-Scale Earth, pinched the roll with tweezers near the top and bottom to give it the appearance of being tied, removed the wire, and laid the canvas roll on the closed louvers. The wet paint glued the roll in place. The model was weathered by airbrushing with Floquil Grime, Grimy Black, and Mud. Scalecoat Engine Black was used to simulate fuel and oil residue. I added the jewels to the marker lights last. Figure 24 Finished model fireman s side
14 There is a long list of details that could still be added to these models to enhance their appearance even more. The details that I added give the model that unique M&StL appearance that is so appealing to all of us. Clark Propst M&StL detail inspiration from Louis Cleason PDF file by Tom Wencl
Jay Kershaw Models Coolum (Moreton Mill's B-B DH) in 7mm Scale
Jay Kershaw Models Coolum (Moreton Mill's B-B DH) in 7mm Scale Introduction Jay wrote about his use of 'scrapbook' paper punches for modelling in Narrow Gauge Down Under (NGDU 38: July 2010, pp 28-9).
More informationFLEX KEY ASSEMBLY. ..._ o RAFTER ARM TUBE MAIN ARM TUBE CAP NUT CLAW HINGE
ZIP DEE Inc. 96 Crossen Ave. Elk Grove Village, IL 60007(847)437-0980 (800)338-2378 HEAD CASTING AWNING RAIL FLEX KEY ASSEMBLY..._ o GM1 Installation Instruction GMC Motorhome RAFTER ARM TUBE MAIN ARM
More informationHow to Build Your Own Flour Mill and Sifter
Prototype and plans developed by Hugo Gervais Custom Fabrication, North Hero, VT Materials List: How to Build Your Own Flour Mill and Sifter Quantity Materials 4 2 X 2 X 26 3 / 16 Square tubing 1 2 X 2
More informationInstallation manual. Awning. V480 Cannes
Installation manual Awning V480 Cannes Installation manual awning V480 Cannes Content 1. Awning * 2. Wall supports 3. Extra support(s) (with an awning bigger than 350 cm) 4. Mounting plates (optional)
More informationINSTALLATION INSTRUCTIONS for automatic awnings
Custom made Awnings and Blinds Item No 0756 INSTALLATION INSTRUCTIONS for automatic awnings AUTOMATIC AWNING IMPORTANT INFORMATION BEFORE INSTALLING YOUR AUTOMATIC AWNING Updated 08/09/15 AN AWNING INSTALLATION
More informationSolera Power Awning OEM INSTALLATION MANUAL
Solera Power Awning OEM INSTALLATION MANUAL TABLE OF CONTENTS System Information 2 Safety 2 Prior To Installation 2 Resources Required 2 Awning Rail Installation (If Needed) 3 Installation 3 Awning Installation
More informationSun awning V225 Porto
Installation manual Sun awning V225 Porto semi-cassette Content package 1. Sun awning * 2. Control a. Manual control: crank handle b. Electrical: switch + plug c. Remote controlled: remote control + plug
More informationSOLHARO ASSEMBLY & INSTALLATION INSTRUCT IONS
A. Introduction: SOLHARO ASSEMBLY & INSTALLATION INSTRUCT IONS Rev. 01/30/2012 The Solharo is an external, retractable, tensioned sun shading system designed to fit over a sunroom or wood pergola. The
More informationSolera Power Awning w/ LED Lights OEM INSTALLATION MANUAL
Solera Power wning w/ LED Lights OEM INSTLLTION MNUL TBLE OF CONTENTS Safety 2 Prior to Installation 2 Resources Required 2 wning Installation 3 wning Rail Installation (If Needed) 3 wning Support rm Installation
More informationFyre-Stones Set C Installation Instructions (sku )
Items Required ¼ Crushed Glass (see page 14 for quantities): -- Platinum (94500580) -- Reflective Bronze (94500581) -- Cobalt (94500582) Compatibility 33 DVI DVL GSR NB with Dancing-Fyre Burner 864 HO
More informationAssembling A Pennine Awning: A Pictorial Guide Below is a step by step pictorial guide to setting up a Pennine awning. This guide is based on the older, heavy duty awning poles, and the smaller awning
More informationOtter Pro X-Over Lodge Installation and Set-Up Instructions
Otter Pro X-Over Lodge Installation and Set-Up Instructions Otter Pro X-Over Lodge Fits Magnum Otter II & Pro Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro X-Over Lodge
More informationNotes, Parts List & Drawings
Biomass Chopper/Cutter Notes, Parts List & Drawings Page 1 of 16 The Easy BioChop biomass chopper/cutter was designed to cut both wet and dry biomass and to accomplish a number of goals. The objectives
More informationInstallation Instructions for the Rolltec Physique XL Awning
Installation Instructions for the Rolltec Physique XL Awning Questions? Call Rolltec at 1-800-667-0474 General Tool Requirements Table of Contents Available installation brackets Side dimensions of various
More informationLITE Spear Awning Instructions
LITE Spear Awning Instructions IMPORTANT NOTE: Please take a few minutes to become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and
More informationOWNER'S MANUAL FREEDOM AWNINGS
OWNER'S MANUAL FREEDOM AWNINGS RV PATIO, WINDOW AND OTD AWNINGS Freedom Patio Awning Freedom Window and OtD Awnings Special Note: This manual provides a basic description of the product and the standard
More informationOtter Pro XT Cabin Installation and Set-Up Instructions
Otter Pro XT Cabin Installation and Set-Up Instructions Otter Pro XT Cabin Fits Medium Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro XT Thermal Cabin
More informationBUILDING A BANNER STAND & STANDARD
BUILDING A BANNER STAND & STANDARD These instructions are for a simple, inexpensive, and portable banner stand and standard. More attractive stands can be made from hardwoods. The taller the banner, the
More informationTuf-Lite and Tuf-Lite II Fans 6000M Series Hub
Tuf-Lite and Tuf-Lite II Fans 6000M Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 32.8 or 10 Meter Diameter Hudson Tuf-Lite and Tuf-Lite II fan blades Hudson Tuf-Lite (black) fan blades
More information10 Economy Popup Tent
10 Economy Popup Tent ZM-TNT-ECO-3MX3M The Zoom Tent is great for outdoor fairs, exhibitions, sporting events and arenas, concerts, festivals and more. Strong, solid, stable, wind-resistant & durable.
More informationStructural Mullion System
Structural Mullion System Installation Instructions DNA Part Number 10300085 This system is designed to allow for larger window combinations. It is not intended to replace structural members in a building.
More informationCONVEX Awning Instructions
CONVEX Awning Instructions IMPORTANT NOTE: Please take a few minutes to become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and will
More informationOWNER'S MANUAL CAMPOUT TABLE OF CONTENTS
OWNER'S MANUAL CAMPOUT RV Before operating the awning, carefully review the Owner's Manual. The manual contains important safety information, detailed operating instructions, common maintenance procedures
More informationRT INTERNATIONAL CATALOGUE TOOLS FOR EVERY APPLICATION LEADERS IN THE FIELD OF JEWELLERY TOOLS AND EQUIPMENTS
RT INTERNATIONAL LEADERS IN THE FIELD OF JEWELLERY TOOLS AND EQUIPMENTS CATALOGUE TOOLS FOR EVERY APPLICATION SINCE 2010 13 ABOUT US Established in the year 2010, Our pursuit of getting outstanding recognition
More informationSolera Classic Awning OEM INSTALLATION MANUAL
Solera Classic Awning OEM INSTALLATION MANUAL TABLE OF CONTENTS System and Safety Information 2 Preparation 3 Resources Required 3 Installation 3 Installing the Awning Rail (If Necessary) 3 Assembling
More informationPIONEER LITE PATIO AWNING OWNER'S MANUAL
A Manual Crank Operated Awning RV OWNER'S MANUAL TABLE OF CONTENTS Introduction... 2 Operating the Awning... 3 To Open the Awning:... 3 Adjusting the Pitch... 4 Rain Release Setting... 4 Setting the Arms
More information* * KR54-F, KR9854 & KR9954 Installation Instructions. Read All Warnings Before Starting Installation! Index:
*941061-00* 941061-00 Keyed Removable Mullion KR54-F, KR9854 & KR9954 Installation Instructions CLASSIFIED CLASSIFIED C Read All Warnings Before Starting Installation! Index: General Information ----------------
More informationL&W ENGINEERING INC.
L&W ENGINEERING INC. 2012-2013 107 INDUSTRIAL PARKWAY MIDDLEBURY, IN 46540 PHONE (574) 825-5351 FAX (574) 825-1006 WWW.LW-ENG.COM Pipe Hangers Welcome to L&W Engineering. Your quality source for fabricated
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationADVANCE RESERVATION FORM 1224 Boston Ave Phone: (303) Longmont, CO 80501
ADVANCE RESERVATION FORM 1224 Boston Ave Phone: (303) 772-1901 Longmont, CO 80501 Fax: (303) 772-8534 Sales: (800) 472-2530 SEPTEMBER 2015 Customer: Telephone #: Dealer#: Other: Contact: - HO Scale GP16
More informationRead all instructions and warnings before using this fireplace. WARNING
Frame User Manual 1 Operating Manual Thank you for purchasing this Signi Fires product. Signi Fires is very safety conscious, we have taken every care in designing, manufacturing and assembling your Signi
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS KR54, KR1654, & KR4954 Keyed Removable Mullion NOT FOR USE ON ELECTRIC OR FIRE RATED MULLIONS. This kit includes the following parts: (Not to scale) WARNING Remove key, reinstall,
More informationHonda Ridgeline Installation Instructions
Honda Ridgeline Installation Instructions READ THIS... If you read these instructions from beginning to end before starting you will probably not need to look at them again during the installation, but
More informationFEATURES & BENEFITS OF THE TOW PRO LITE :
To Protect & Preserve PRODUCT MANUAL & FITTING GUIDE tow pro lite TYPE: SEMI - FIT EACH TOW PRO LITE COMES WITH THE FOLLOWING : 16 side securing straps & buckles (8 either side) 1 HITCH STRAP & buckles
More informationOtter XT 650 Cabin Installation and Set-Up Instructions
Otter XT 650 Cabin Installation and Set-Up Instructions Otter XT 650 Cabin Fits Medium Otter Wild Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Otter XT 650 Cabin 200891 2 1
More informationUNIVERSAL PANEL & EASY PLUMB KIT
1 x 550mm Radius Curved Panel UNIVERSL PNEL & ESY PLUMB KIT To be read in conjunction with the Shower Tray installation instructions CONTENTS 2 x 1200mm Universal Straight Panels 6 x Hexagon Leg Sets 16
More informationWv410 window. Installation Instructions
Wv410 window Installation Instructions Part NO. Y007 February 2014 TABLE OF CONTENTS SECTION PAGE I. Product Description and Limitations..........3 II. General Statements and Definitions........3 III.
More information250 SERIES 1" STRUCTURAL TUBE MULLION ASSEMBLY INSTRUCTIONS
2014 Pella Corporation Part Number: V985711 250 SERIES 1" STRUCTURAL TUBE MULLION ASSEMBLY INSTRUCTIONS Be sure to thoroughly read and understand all the steps before beginning the mullion assembly process.
More informationTall Cabinet Drawer Keyless Double Lock Installation [ xx]
Tall Cabinet Drawer Keyless Double Lock Installation [002-97-xx] Note This install can be used for any Tall Cabinet Double Drawer Keyless Lock installation. The assembly process will be the same. The will
More informationOtter Pro XT 1200 Cottage Installation and Set-Up Instructions
Otter Pro XT 1200 Cottage Installation and Set-Up Instructions Otter Pro XT 1200 Cottage Fits Small Ultra-Wide Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete
More informationArchitectural Manual. Thermally Improved Aluminum Series Windows & Patio Doors
Architectural Manual Thermally Improved Aluminum Series Windows & Patio Doors Instructions on how to use this manual: This document has been designed for easy navigation and to quickly click to the section
More informationSolera Family and Screen Room. Installation and Owner s Manual (For Aftermarket Applications) Table of Contents
Solera Family and Solera Family and Installation and Owner s Manual (For Aftermarket Applications) Table of Contents Introduction 2 Preparation 2 Resources Required 2 Installation 3 Install Upper Brackets
More informationINSTRUCTIONS INSTALLATION UNIVERSAL SERIES PATIO AWNING HARDWARE , , ,
RECORD THIS INFORMATION FOR FUTURE REFERENCE: Model Number Serial Number Hardware Model Number Hardware Serial Number Date Purchased Retailer / Qualified Installer INSTALLATION INSTRUCTIONS UNIVERSAL SERIES
More informationASSEMBLY & CARE INSTRUCTIONS
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 3 9 Part No. FT3711 - on road FT3923 - off road OPTIONAL SUNROOM Wall and floor kit Part No. FT3723 - on road FT39 - off road OPTIONAL SPARE ROOM Roof,
More informationTuf-Lite III Fans 4000KW Series Hub
Tuf-Lite III Fans 4000KW Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 11 through 20 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HATCH KIT Application 201 PILOT Publications No. VERSION 1 Issue Date 201 PARTS LIST Stake bag Tent bag 13 Stakes 4 Guide ropes Tent 2 Awning pole caps 2 Tie straps
More informationHARD DOOR UPGRADE KIT
RV Accessories OWNER'S MANUAL HARD DOOR UPGRADE KIT FOR ADD-A-ROOM & BREEZEWAY SCREEN ROOMS THIS MANUAL SUPPLEMENTS THE ADD-A-ROOM INSTRUCTIONS TABLE OF CONTENTS First Time Assembly... 2 Assembling the
More informationFood Prep. Mixing Bowls. Colanders. Fryer Baskets. Fryer Basket. Heavy weight stainless steel bowls. Item # Description Pk
Food Prep Mixing Bowls Heavy weight stainless steel bowls. Item # Description Pk 4900 3 4 qt 12 4901 1 1 2 qt 12 4903 3 qt 12 4904 4 qt 12 4905 5 qt 12 4908 8 qt 12 4913 13 qt 12 4916 16 qt 12 4920 20
More informationOtter XT Cabin Installation and Set-Up Instructions
Otter XT Cabin Installation and Set-Up Instructions Otter XT Cabin Fits Medium Otter Wild Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Otter XT Cabin 200962 2 1 PARTS LIST
More information635 Wilmer Ave. Orlando, Fl Ph Fx
Where Function And Elegance Meet Under The Sun 635 Wilmer Ave. Orlando, Fl. 32808 Ph. 407.898.6001 Fx. 407.852.1313 www.theawningfactory.com info@theawningfactory.com DEDICATION For over 30 years, The
More informationASSEMBLY & CARE INSTRUCTIONS. 7 x4 TRAILER TENT SERIES 4 9. OPTIONAL SUNROOM Wall and floor kit. OPTIONAL SPARE ROOM Roof, wall and floor kit
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 9 Part No. TM709 OPTIONAL SUNROOM Wall and floor kit Part No. TM723 OPTIONAL SPARE ROOM Roof, wall and floor kit Part No. TM76 Please keep these instructions
More information* * 4023 KR. Step 1 Prepare the Keyed Removable Unit. Not for use on electric or fire rated removable mullions
condition. *64009-00* 64009-00 Keyed Removable Mullions 403 KR Installation Instructions Not for use on electric or fire rated removable mullions This kit includes the following parts: (Not to scale) 5/6
More informationGerjak Dear Customer, You will find below information that includes: Is the caravan rail in order? Is everything in place?
Gerjak Dear Customer, We would like to wish you much pleasure with your new Gerjak product. We very much appreciate that you have chosen our product! Following are some hints and tips to give you pleasure
More informationModel. Oasis Automatic and Manual RV Door Awning System INSTALLATION & OPERATING INSTRUCTIONS
Oasis Automatic and Manual RV Door Awning System USA SERVICE OFFICE Dometic Corp. 509 So. Poplar St. LaGrange, IN 46761 260-463-4858 CANADA Dometic Dist. 866 Langs Dr. Cambridge, Ontario CANADA N3H 2N7
More informationINSTALLATION INSTRUCTIONS FOR BALCO, INC. FLOOR MATS FM2R-(A, C, D) W/O FRAME 4V
2626 South Sheridan PO Box 17249 Wichita, Kansas 67217 Phone: (316) 945-9328 Fax: (316) 945-0789 INSTALLATION INSTRUCTIONS FOR BALCO, INC. FLOOR MATS FM2R-(A, C, D) W/O FRAME 4V 2012, Balco, Inc. INSTALLATION
More informationFILTERED FAN PACKAGES
FILTERED FAN PACKAGES PLASTIC & METAL FILTERED FANS EFFICIENT, QUITE BALL BEARING MOTORS NEMA TYPE 1 AND 3R ALL KITS INCLUDE GASKETS, HARDWARE, AND TEMPLATE UL LISTED Plastic FILTER FAN PACKAGES Injection
More informationINSTALLATION INSTRUCTIONS for vertical awnings
Custom made Awnings and Blinds Item No 0759 INSTALLATION INSTRUCTIONS for vertical awnings IMPORTANT INFORMATION BEFORE INSTALLING YOUR Updated 08/09/15 AN AWNING INSTALLATION IS A HOME IMPROVEMENT PROJECT
More informationCable Marking Systems FLEXIMARK
Cable Marking Systems FLEXIMARK 9 595 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (6) 588-90-Outside Local Area: (800) 258-90-www.stevenengineering.com
More informationIMPORTANT! HAVING PROBLEMS? INSTALLATION QUESTIONS? NEED PARTS? TROUBLESHOOTING? PLEASE DON T RETURN THIS PRODUCT TO THE STORE CONTACT US FIRST
Owners Manual For Retractable Awning SKU# 443-0875 Model# 30100 IMPORTANT! HAVING PROLEMS? INSTALLATION QUESTIONS? NEE PARTS? TROULESHOOTING? PLEASE ON T RETURN THIS PROUT TO THE STORE ONTAT US FIRST ecko
More informationSILENT MODEL WAR WINGS
A Stinson 0-49 tows an army glider, not full scale, just models. The glider is shown below SILENT MODEL WAR WINGS Building a high efficiency model of Uncle Sam's latest training glider by EARL STAHL THE
More informationINSTALLATION INSTRUCTIONS AND OWNER'S MANUAL AWNINGS. For trailers & motor homes with straight sides TOOLS REQUIRED
AWNINGS INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL For trailers & motor homes with straight sides TOOLS REQUIRED 1/4" electric drill Ratchet handle kit 3/8" & 7/16" socket No. 1 and No. 2 screwdriver
More informationInstallation Instructions for the Rolltec Adalia X3M Extenda Awning
Installation Instructions for the Rolltec Adalia X3M Extenda Awning Questions? Call Rolltec at 1-800-667-0474 General Tool Requirements Table of Contents Available installation brackets Side dimensions
More informationF a l l P r o t e c t i o n E x p e r t s. Subject: Buckle Specifications and Operations
Technical Bulletin Subject: Buckle Specifications and Operations DBI/SALA uses four types of buckles in full body harnesses, body belts and other fall protection equipment: parachute buckles, pass through
More informationInstallation manual. Drop-arm awning. V120 Napoli
Installation manual Drop-arm awning V120 Napoli Installation manual drop-arm awning V120 Napoli Content 1. Drop-arm awning * 2. Control a. Manual control: crank handle b. Manual control: strap coiler
More informationADDED PROTECTION FOR SLIDE-OUT ROOMS. Installation. Introduction... 2 Product Overview...2 Component Checklist...3
CAREFREE SIDEOUT KOVER II RV Installation ADDED PROTECTION FOR SLIDE-OUT ROOMS TABLE OF CONTENTS SOKII Shown with Full Case Option Introduction... 2 Product Overview...2 Component Checklist...3 Installation...
More informationPIONEER LITE PATIO AWNING
A Manual Crank Operated Awning RV OWNER'S MANUAL Before operating the awning, carefully review the Owner's Manual. The manual contains important safety information, detailed operating instructions, common
More informationB.R. CONFLAT A. WW 02
B.R. CONFLAT A. WW 02 History. B.R. produced no fewer than six main types of conflat wagons between 1951 and 1958, with the most numerous being the conflat A, for which six different diagrams were issued.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HATCH KIT Application 2014 CR-V Publications No. AII 50018 Issue Date JULY 2013 Put this information in the glove box with the vehicle owner s manual PARTS LIST 4 Guide
More informationTherme storage water heater. Table of contents. Symbols used. Symbols used Symbol indicates a possible hazard. Installation instructions
Therme storage water heater Table of contents Symbols used... 8 Installation instructions Water supply... 9 Choice of location... 9 Installation of the Therme... 9 Fitting the draining and venting valve...
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HATCH KIT Application 2009 ELEMENT Publications No. AII 41008 Issue Date DEC 2008 PARTS LIST Tent bag 13 Stakes 4 Guide ropes Tent 2 Awning pole caps Gear loft 2 Tie
More informationTuf-Lite and Tuf-Lite II Fans 6000 Series Hub
Tuf-Lite and Tuf-Lite II Fans 6000 Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 32 and 33 Diameter Hudson Tuf-Lite and Tuf-Lite II fan blades Hudson Tuf-Lite (black) fan blades are made
More informationCompass Home 8' x 8' No Tools Gazebo with Awning and Anchor Bags Assembly Instruction for Gazebo (no tools required)
Compass Home 8' x 8' No Tools Gazebo with Awning and Anchor Bags Assembly Instruction for Gazebo (no tools required) CAUTION: Read all instructions before assembly. Failure to do so may result in faulty
More informationHUNTCO SITE FURNISHINGS. Double Bike Locker Assembly Instructions HUNTCO SITE FURNISHINGS
Double Bike Locker Assembly Instructions Includes instructions for both handle styles. Padlock Handle with U Lock Box and Keyed Pop Out T Handle SITE FURNISHINGS SITE FURNISHINGS and architectural site
More informationPrimrose Awnings Full Cassette Manual & Electric Instructions
Primrose Awnings Full Cassette Manual & Electric Instructions Contents for Full Cassette Awning 1 x Remote control receiver box 2 x Remote hand-held zappers 1 x 5 metre cable 1 x Template sticker **The
More informationOPERATOR INSTRUCTION MANUAL INCLUDING REPAIR PARTS FOR MODULAR GENERAL PURPOSE TENT SYSTEM (MGPTS) TYPE I
OPERATOR INSTRUCTION MANUAL INCLUDING REPAIR PARTS FOR MODULAR GENERAL PURPOSE TENT SYSTEM (MGPTS) TYPE I Johnson Outdoors Gear, Inc. Eureka! branded tent products 625 Conklin Road Binghamton, NY 13903
More informationSYSTIMAX RoloSplice Multiple Splice Organizer Installation
SYSTIMAX RoloSplice Multiple Splice Organizer Installation General This instruction sheet provides procedures for installing the SYSTIMAX RoloSplice, multiple splice organizer management system and is
More informationTuf-Lite II Fans 7000 Series Hub
Tuf-Lite II Fans Series Hub INSTALLATION MANUAL Hudson Tuf-Lite II fan blades Adjustable Pitch Fan Assembly 34 & 3 Diameter Hudson Tuf-Lite II (white, prev. blue***) fan blades are made from fiberglass
More informationInstallation manual. Drop-arm awning. V124 Calpe
Installation manual Drop-arm awning V124 Calpe Installation manual Drop-arm awning V124 Calpe Content 1. Drop-arm awning * 2. Wall supports 3. Control a. Manual control: crank handle b. Electrical control:
More information[tips & tricks for modelmakers] Plate 4 Decks. Required tools
Plate 4 Decks 2 4 18 3 Required tools 13 12 25 11 25 1 24 6 7 15 14 21 22 26 19 17 5 22 25 17 25 10 27 20 19 26 21 9 8 1 Gun locks 1 Do not cut the small link from the lock to the fret as it provides good
More information80070 TOP MOUNT CAMPER SHELL and TRANSIT CONNECT RACK TMCS_3:1
ASSEMBLY INSTRUCTIONS for : 80070 TOP MOUNT CAMPER SHELL and TRANSIT CONNECT RACK TMCS_3:1 (916) 638-8703 (800) 343-7486 11261 Trade Center Drive Rancho Cordova, CA 95742 www.kargomaster.com Transit ASSEMBLY
More informationTWO PERSON WALL MOUNT
ONE TIER TWO TIER THREE TIER FOUR TIER FIVE TIER SIX TIER 16 PERSON TWO PERSON WALL MOUNT Specifications Body: Entire unit (bottom, sides, top, back, and shelves) constructed of mild cold rolled 24 ga.
More informationWhen moving the frame don t force anything! Move the leg to allow the brace to go over the rod.
THE IDLER Assembly and Care Instructions General notes Please read these instructions in their entirety before constructing your Idler Construction Before you begin constructing your Idler consider where
More informationREAD AND SAVE THESE INSTRUCTIONS! EasyAwn Dome Awning Installation
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Dome Awning Installation
More informationInstructions for turning a pair of 2012 Large Rolie Bags into Tank Panniers. This is a "Do it yourself " Kit.
Instructions for turning a pair of 2012 Large Rolie Bags into Tank Panniers. This is a "Do it yourself " Kit. ***The Large Rolie bags function best when full as they have no stiffeners****************
More informationMEMO DEALER LETTER JUNE-2015
1224 Boston Ave Longmont, CO 80501 Phone: (303) 772-1901 Fax: (303) 772-8534 E-Mail: intermountain@intermountain-railway.com Web Site: www.intermountain-railway.com TO: INTERMOUNTAIN RAILWAY COMPANY DEALERS
More informationBLOWLAMP NEWS BN 100 SEPTEMBER 2017
THE DARLTON STORY By Arthur McNamara and Mal Mutimer The Darlton blowlamp was manufactured in Australia by the Prymace Engineering Company Pty Ltd of Sydney between 1944 and 1947 and then by Commonwealth
More informationSuggested tools: Flat head screw driver, power drill, ¼ drill bit, 24 level, and a tape measure. HARDWARE LIST (2) FUEL CANISTER HOLDER
SOUTHERN ENTERPRISES INC. This product has been engineered for easy installation and is constructed for durability. Please take the time to read through and follow these assembly instructions. YOU CAN
More informationModel STEEL-VISION Perforated Curved or Flat Slats Rolling Service Door
Model STEEL-VISION Perforated Curved or Flat Slats Rolling Service Door NOTE: For specifications, architects must choose from a variety of options. The standard choice will be shown first in plain text
More informationAwning Windows Premium Atlantic Vinyl
TABLE OF CONTENTS Specifications... 2-2 QuickSpecGuide... 2-3 Elevations/Sizes: 1/4 Scale FullAwning... 2-4 GlazingOptions: 3 Scale... 2-6 Grille Patterns... 2-7 SectionDetails: 6 Scale... 2-8 JELD-WEN
More informationAssembly and Installation Instructions
U.S. patent number 8,708,369 part number 4750 for Blue Ox tow bars with Blue Ox brackets, Demco tow bars with Demco brackets, and all motorhome-mounted ROADMASTER tow bars Assembly and Installation Instructions
More informationJOINING MULLION (DIRECT MULL) ASSEMBLY INSTRUCTIONS FOR 3-WAY OR 4-WAY JOINTS FOR IMPERVIA AWNING, CASEMENT AND LARGE AWNING
2014 Pella Corporation JOINING MULLION (DIRECT MULL) ASSEMBLY INSTRUCTIONS FOR 3-WAY OR 4-WAY JOINTS FOR IMPERVIA AWNING, CASEMENT AND LARGE AWNING For Additional Mullion Assembly Information; Visit www.installpella.com/mullions,
More informationTCWS54 SEE THRU DIAMOND BURNER INSTALLATION KIT INSTRUCTIONS
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationTIN KNOCKER TK NO. 30 CLEAT BENDER INSTRUCTIONS & PARTS DIAGRAM. TK No. 30 CLEAT BENDER
1 TIN KNOCKER TK NO. 30 CLEAT BENDER INSTRUCTIONS & PARTS DIAGRAM TK No. 30 CLEAT BENDER Sheet Metal Equipment Sales Inc. Dean P. O'Connell, President Green Bay, Wisconsin Phone - (920)-662-9966 Fax -
More informationTrinket Box. Kit Inventory
Kit Inventory Trinket Box o Top Panel o Bottom Panel o Two (2) End and two (2) Side Box Pieces o Two (2) End and two (2) Side Lid Pieces o Right Latch Holder & Left Latch Holder o Two (2) Lock Bar Guides
More informationOWNER'S MANUAL CAMPOUT TABLE OF CONTENTS
OWNER'S MANUAL CAMPOUT RV Before operating the awning, carefully review the Owner's Manual. The manual contains important safety information, detailed operating instructions, common maintenance procedures
More informationUser s Manual Trampoline 8
User s Manual Trampoline 8 Model! WARNING Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Maximum user weight 17 lbs. ASSEMBLY IMPORTANT
More informationAssembly and Installation Instructions
U.S. patent number 8,708,369 part number 4750 for Blue Ox tow bars with Blue Ox brackets, Demco tow bars with Demco brackets, and all motorhome-mounted ROADMASTER tow bars Assembly and Installation Instructions
More informationRoller Bar End Cap (w/round Drive Shaft) Replacement Instructions for Vista and Motorized Awnings * Helpers needed *
RETRACTABLE AWNINGS For Technical Support visit us at www.sunsetter.com/ownerscorner or Call Toll Free 800-670-7071 Fax 877-224-4944 Roller Bar End Cap (w/round Drive Shaft) Replacement Instructions for
More informationWall Tent Set Up & Care Instructions
Wall Tent Set Up & Care Instructions Congratulations on the purchase of your new Colorado Tent! Your Wall Tent frame includes color coded poles for easy set up. Wall (Side) Poles: Red Roof / Rafter Poles:
More informationCHALET BURNER KIT TC42.NG01
CHALET BURNER KIT TC42.NG01 PACKAGE CONTENTS: BURNER ASSEMBLY PART # TC42.908501 LOG GRATE PART # TC42.9081 TC42 LOGS PART # 5098.31061 EMBER MATERIAL PART # 5096.981.B HARDWARE PACKAGE PART # TC36.NGHDWR
More information