42-YP Series. Serie 42-YP Série 42-YP. Single Control Lavatory Faucet Grifo Monomando para el Baño Mitigeur de Robinet pour Lavabo

Transcription

1 42-YP Series Serie 42-YP Série 42-YP Single Control Lavatory Faucet Grifo Monomando para el Baño Mitigeur de Robinet pour Lavabo EO6852C Copyright 2005, Price Pfi ster, Inc. A COMPANY

2 Thank you for purchasing this Price Pfister product. All Price Pfister products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions. If you have any questions regarding this product, call Pfaucet ( ) 1 BEFORE PROCEEDING FAUCET INSTALLATION WARNING: Read all the instructions completely before proceeding. Price Pfister recommends calling a professional if you are uncertain about installing this product! 5 This product should be installed in accordance with all local and state plumbing and building codes. 5B 2 5A 5C 5D 2 SHUT OFF WATER SUPPLY Locate water supply inlets and shut off the water supply valves. These are usually found under the sink or near the water meter. If you are replacing an existing faucet, remove the old faucet from the sink and clean the sink surface thoroughly. 5E 3 5 INSTALLING FAUCET WITH SINGLE HOLE MOUNTING Ensure that Base Plate (5C) is pressed onto Base Ring (5A 5 ). Place a bead of 5A plumber s putty in the groove along the bottom outer edge of Base Plate (5C). Assemble Base Plate and Base Ring to Faucet Body (5B). From above sink, insert Threaded Shank (5D) and Flexible Tubing (5E) through hole on sink. 3 TOOLS RECOMMENDED Plumber's putty Slotted screwdriver Philips head screwdriver Pliers Adjustable wrench Flashlight Cloth PTFE Plumber's Tape Your installation may require new supply lines and / or shut-off valves or other additional tools. 4 A 6 C B 6C D 6D E 6B F 6A K G J H 4 CHECKING THE CONTENTS OF THE BOX Upon opening the box, check to ensure that all of the following items are included. A Faucet D Base Plate G Metal Washer K Pop-up Assembly B Lift Rod E Deckplate H Long Nut C Base Ring F Putty Plate J Adapters If any of these items are missing, please contact Price Pfister Consumer Service at Pfaucet ( ). 6E 2 6 INSTALLING FAUCET WITH DECKPLATE Ensure that the Plastic Putty Plate (6A) is pressed on the Deckplate (6B). Place a bead of plumber s putty in the groove along the outer edge of the Putty Plate (6A). Assemble Deckplate (6B) and Putty Plate (6A) to Faucet Body (6C). With the handle and spout facing forward, carefully install the Faucet Supply Hoses (6D) through the center hole of sink (6E). 6E 6E).

3 7 DRAIN BODY INSTALLATION 7E 7A 10 10F 7D 7B 10A 7C 10D 10E 7 SECURING FAUCET From underneath sink, secure Faucet Body (7A) by placing Metal Washer (7B) and threading Long Nut ( 7 /16 Hex.) (7C) onto Mounting Post (7D). Make sure that the bumps on Metal Washer (7B) are facing up. Tighten loosely, make sure Handle (7E) swings equally in both directions. Firmly hand tighten Long Nut (7C). Secure Long Nut (7C) not to exceed a 1/4 turn. Caution: Do not over tighten! 8 8E 10 POP-UP PREPARATION Remove Flange (10A) from the Drain Body (10B). Remove Locknut (10C), Friction Washer (10D), Rubber Washer (10E) and Stopper (10F) from Flange (10A) C 10B 8B 8C 11A 8A 8A 11B 11C 8D 11D 8 WATER SUPPLY CONNECTIONS If needed, thread the ½ NPSM Adapters (8A) into the ⅝ Nuts (8B). Tighten using wrenches on both the Adapters and the Nuts. Connect water Supply Lines (8D) to Faucet Inlets (8C). Hot water supply line goes to hot inlet fitting indicated by Red Tag (8E). (Supply lines not included). Follow manufacturer s instructions when installing supply lines. 9 9A 11F 11G 11E 11H 9 POP-UP ROD CONNECTION Insert Lift Rod (9A) into hole at the back of Faucet Body (9B). Gently, slide Lift Rod (9A) down the hole in Faucet Body (9B). 9B 3 11 POP-UP INSTALLATION The Flange (11A) can be installed with or without Rubber Seal (11B). If Flange (11A) is installed without Rubber Seal, apply a small bead of plumber s putty underneath the Flange (11A) and around Drain Opening (11C). Insert Flange (11A) into Drain Opening (11C). From underneath, slide Rubber Washer (11D) and Friction Washer (11E) onto the bottom of Flange (11A). Thread Locknut (11F) until Rubber Washer (11D) seats securely inside Drain Opening (11C). Remove excess plumber s putty. Wrap PTFE plumber s tape to the bottom external threads of Flange (11A) according to manufacturer s instructions. Thread Drain Body (11G) to bottom of Flange (11A) and adjust so that the Ball Rod Opening (11H) faces the rear.

4 12 12E 14 14F 14G 12C 12A 12F 12B 14B 14E 12D 14D 14C 12 BALL ROD PREPARATION Unscrew Nut (12A) from the Drain Body (12B) and retain one Packing Ring (12C) inside the Ball Rod Opening (12D). Take off the Spring Clip (12E) from the Ball Rod (12F). 14A 14A 14B 14C 14 POP-UP ROD LINKAGE & ADJUSTMENT Place one end of Spring Clip (14A) onto the end of Ball Rod (14B). Insert the Ball Rod (14B) through a hole of Strap (14C). Connect the other end of Spring Clip (14A) to Ball rod (14B). Insert bottom of Lift Rod (14D) into the hole on top of Strap (14C). Adjust the Lift Rod (14D) height by tightening the Thumb Screw (14E) on the Strap (14C) or by placing the Ball Rod (14B) on another hole of Strap (14C). Be sure to leave enough space between Lift Rod Knob (14F) and Faucet Body (14G) when Lift Rod is down A 13C 15 UNIT START UP Turn on hot and cold water supplies, and check for leaks above and below the sink. 13B FAUCET FUNCTION 13G 13F 13D 13D 13E 16 OPEN 13H 16A HOT COLD 16A 13 POP-UP BALL ROD INSTALLATION Drop the Stopper (13A 13 ) into Drain Body (13B) with the Off-Set (13C) facing 13A the rear. Place Nut (13G) and the other Packing Ring (13H) onto Ball Rod (13D). Insert the Ball Rod (13D) into the Ball Rod Opening (13E) through the Stopper Hole (13F) and secure with Nut (13G) VALVE FUNCTION By lifting the Lever Handle (16A) up, the valve will be activated allowing water to flow. The water flow will increase by continuing to lift up the Lever Handle (16A). By rotating the Lever Handle counter-clockwise, the water temperature will decrease to cold flow only. By rotating the Lever Handle clockwise, the water temperature will increased to hot flow only.

5 17 MAINTENANCE & CARE 18 18A 17B 17A 18B 18C 17 HANDLE REMOVAL Using a 3 /32 Allen wrench, loosen Set Screw (17A) and remove Handle (17B). 18 CARTRIDGE REPLACEMENT Turn off water supplies and relieve pressure before working on your faucet. Remove handle (see figure 17). Remove the Dome Cap (18A8 ) by unscrewing counterclockwise. Using pliers, unscrew the retainer ring (18B). Carefully remove the Cartridge (18C) by pulling it straight up and out. Reassemble valve by reversing steps. CAUTION: Maintenance DISASSEMBLY 1. Replacement parts may be available at the store where you purchased your faucet. 2. When replacement parts are not available, please write or call Price Pfister Consumer Service. 3. Always turn off water and relieve pressure before working on your faucet. NOTE: Trim Care Cleaning Instructions: For all Handles and decorative fi nishes, use only a soft damp cloth to clean and shine. Use of polish, detergents, abrasive cleaners, organic solvents or acid may cause damage. Use of other than a soft damp cloth will nullify our warranty! Special Trim: Trim products which contain Porcelain or other similar substance are not acceptable for public areas or Commercial use. Installation of Said Trim is at Users Risk! PFAUCET ( ) For Toll-Free Pfaucet information call PFAUCET ( ) or visit ster.com Installation Support Care and Warranty Information

6 42-YP * * * * * * * * Letter Designates Finish La Letra Indica el Terminado La Lettre Designe La Fini A Polished Chrome Cromo Pulido Chrome Poli E Rustic Pewter Peltre Rústico Étain Rustique J PVD Brushed Nickel PVD Niquel Cepillado PVD Nickel Brosse U Rustic Bronze Bronce Rústico Bronze Rustique Z Oil Rubbed Bronze Bronce Frotado Con Aceite Bronze Huilé A DaVinci Lake Forest, CA Phone: Pfaucet ster.com COMPANY