LLumar PrecisionCut 4

Transcription

1 LLumar PrecisionCut 4 Dated Created mbl Updated: Issue: What are the plotter condition settings for different film types? Description/Cause: Customer s requesting the plotter condition settings for their plotter. Resolution: 1. According to what type of plotter you have the condition settings will need to be as follows: RX and Jaguar Plotter Condition Settings This plotter has been tested and conditions pre-set. Due to differences in films the pressure points may need adjusting ±5 point. CONDITIONS BLADE TYPE FORCE SPEED OFFSET Condition 1 Solar Control Films oz-50 gf 11.81ips 30cm/s.275 Condition 2 NRM (White Frost) oz-80gf 11.81ips-30cm/s 0 Condition 3 PPF oz-115gf 11.81ips-30cm/s 0 (Paint Protection) Condition 4 4-mil Safety oz-140gf 11.81ips-30cm/s 0 For best results in cutting solar control film, CPFilms recommends using the 25-degree blade ( ). Graphtec FC8000, FC7000, FC5100 and FC2100 This plotter has been tested and conditions pre-set. Due to differences in films the pressure points may need adjusting ±2 point. Conditions BLADE HOLDER USED BLADE USED FORCE SPEED QUALITY KNIFE Condition 1 Solar Controlled Film Blue Tip Win Tint 25º Cb09Ux -5

2 Condition 2 NRM PS2 (White Frost) Condition 3 PPF Condition 4 4 mil Safety Blue Tip Win Tint 45º CB09Ux 0 Blue Tip PPF 45º CB09Ux 0 Blue Tip PPF 45º CB09Ux 0 Condition 5 Anti Graffiti 6 mil Safety Condition 6 7 mil Safety Condition 7 8 mil Safety Condition 8 11 mil Safety Red Tip Safety Film Red Tip Safety Film Red Tip Safety Film Red Tip Safety Film 60º CB15U- K30X 0 60º CB15U- K30X 0 60º CB15U- K30X 0 60º CB15U-K30X 0 For best results in cutting solar control film, CPFilms recommends using the 25-degree blade ( ). Roland GX/CX-300/400/500 Plotter Conditions This plotter has been tested and pressure settings set. Due to differences in films the pressure points may need adjusting ±1 point. Conditions Condition 1 Solar Controlled Film Condition 2 PPF BLADE HOLDER USED Blue Tip Win Tint Blue Tip Win Tint BLADE USED FORCE SPEED QUALITY OFFSET 25º º Ux 0 For best results in cutting solar control film, CPFilms recommends using the 25-degree blade ( ).

3 CE-5000 and CE-2000 Plotter Conditions Due to differences in films, the pressure points may need adjusting ±2 points. Conditions BLADE HOLDER BLADE USED FORCE SPEED QUALITY KNIFE Condition 1 Solar Control Films Condition 2 NRM PS2 (White Frost) Blue Tip Win Tint Blue Tip Win Tint 25º Cb09Ux -5 45º CB09Ux 0 For best results in cutting solar control film, CPFilms recommends using the 25-degree blade ( ). SUMMA Condition Settings Tangential Knife Blade Adjustment When the knife depth is set correctly, test patterns will cut through the window film allowing the test cut to be removed from the backing. The blade should leave visible, slight scratches in the surface of the media backing (the film liner), but should never cut through it. Always keep in mind that if the blade force is set correctly (following the settings listed below for different film products), the operator may extend the blade slightly to ensure complete cutting through the film to the liner (see the User s Manual, pages 1-30). If the blade is cutting through the film in some areas but not others, do NOT adjust the blade force. Rather, increase the blade depth very slightly to ensure more uniform depth cutting across the film width. If problems persist, call Tech Support for assistance. Nose Piece Holders There are three different types of Nose Piece Holders: The Standard, Drag, and Sandblast. For best results, use only the Nose Piece Holder for the Drag and Tangential blade. The Standard and Sandblast Nose Piece Holders have bearings located at the base of the Nose Piece that can scratch the film while in use. TANGENTIAL PEN DRAG BLADE BLADE HOLDER HOLDER HOLDER

4 NOSE PIECE USED FOR DRAG AND TANGENTIAL KNIFE BLADE HOLDER (NO BEARINGS) NOSE PIECE FOR STANDARD KNIFE. HAS BEARINGS THAT CONTACT THE FILM (SEE PAGES 1-9 OF USER S MANUAL). NOSE PIECE FORE SANDBLAST KNIFE. HAS BEARINGS THAT CONTACT THE FILM (SEE PAGES 1-9 OF USER S MANUAL). PLOTTER SETTINGS FOR SUMMA SUMMA Configurations for Different Film Types CONFIGURATION for LA 20gr Knife Tip set 0.45

5 Tangential Knife Recut set 5 Cutmedia_set 0 Up_Accerlation Load Down_Accerleration Sheet Mode CONFIGURATION for ATR 40gr Knife Tip set 0.45 Tangential Blade

6 Recut set 5 Cutmedia_set 0 Load Sheet Mode

7 CONFIGURATION for PPF 80gr Knife Tip set 0.45 Sheet Mode ON HP-GL Recut set 5 Cutmedia_set 10 Tangential Blade Load CONFIGURATION for NRM 85gr Knife Tip set 0.45

8 Sheet Mode ON HP-GL/2 Tangential Blade Recut set 5 Cutmedia_set 0 Load CONFIGURATION for 4 MIL Knife Tip set gr

9 Sheet Mode ON Tangential Blade Recut set 5 Cutmedia_set 0 Load CONFIGURATION for 6 MIL 250gr Knife Tip set 0.45

10 Tangential Blade ON Recut set 5 Cutmedia_set 0 Load Sheet Mode CONFIGURATION for 7 MIL 375gr Knife Tip set 0.45 Tangential blade

11 ON Recut set 5 Cutmedia_set 0 Load Sheet Mode CONFIGURATION for 8 MIL 550gr HP-GL/2 Knife Tip set 0.60 Tangential Blade Ink Pen Pressure 80gr

12 Load Sheet Mode ON Recut set 5 Cutmedia_set 0 O

13